Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

Pull some more input subsystem updates from Dmitry Torokhov:
 "An update to the ALPS driver to support the V8 protocol with
  touchstick, a change for i8042 to skip selftest on many Asus laptops
  which helps to keep their touchpads working after resume, and a couple
  other driver fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: i8042 - skip selftest on ASUS laptops
  Input: melfas_mip4 - add ic_name sysfs attribute
  Input: melfas_mip4 - add maintainer information
  Input: melfas_mip4 - add devicetree binding documentations
  Input: elantech - add Fujitsu Lifebook E556 to force crc_enabled
  Input: synaptics-rmi4 - fix error handling in I2C transport driver
  Input: synaptics-rmi4 - fix error handling in SPI transport driver
  Input: ALPS - add V8 protocol documentation
  Input: ALPS - set DualPoint flag for 74 03 28 devices
  Input: ALPS - allow touchsticks to report pressure
  Input: ALPS - handle 0-pressure 1F events
  Input: ALPS - add touchstick support for SS5 hardware
  Input: elantech - force needed quirks on Fujitsu H760
  Input: elantech - fix Lenovo version typo

Documentation/devicetree/bindings/input/touchscreen/melfas_mip4.txt

+* MELFAS MIP4 Touchscreen
+
+Required properties:
+- compatible: must be "melfas,mip4_ts"
+- reg: I2C slave address of the chip (0x48 or 0x34)
+- interrupt-parent: interrupt controller to which the chip is connected
+- interrupts: interrupt to which the chip is connected
+
+Optional properties:
+- ce-gpios: GPIO connected to the CE (chip enable) pin of the chip
+
+Example:
+	i2c@00000000 {
+		touchscreen: melfas_mip4@48 {
+			compatible = "melfas,mip4_ts";
+			reg = <0x48>;
+			interrupt-parent = <&gpio>;
+			interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+			ce-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+		};
+	};

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -163,6 +163,7 @@ maxim	Maxim Integrated Products
 meas	Measurement Specialties
 mediatek	MediaTek Inc.
 melexis	Melexis N.V.
+melfas	MELFAS Inc.
 merrii	Merrii Technology Co., Ltd.
 micrel	Micrel Inc.
 microchip	Microchip Technology Inc.

Documentation/input/alps.txt

@@ -319,3 +319,60 @@ For touchpad packet, the format is:
                otherwise byte 0 bit 4 must be set and byte 0/4/5 are
                in NEW fmt
  F:         Number of fingers - 3, 0 means 3 fingers, 1 means 4 ...
+
+
+ALPS Absolute Mode - Protocol Version 8
+---------------------------------------
+
+Spoken by SS4 (73 03 14) and SS5 (73 03 28) hardware.
+
+The packet type is given by the APD field, bits 4-5 of byte 3.
+
+Touchpad packet (APD = 0x2):
+
+           b7   b6   b5   b4   b3   b2   b1   b0
+ byte 0:  SWM  SWR  SWL    1    1    0    0   X7
+ byte 1:    0   X6   X5   X4   X3   X2   X1   X0
+ byte 2:    0   Y6   Y5   Y4   Y3   Y2   Y1   Y0
+ byte 3:    0  T&P    1    0    1    0    0   Y7
+ byte 4:    0   Z6   Z5   Z4   Z3   Z2   Z1   Z0
+ byte 5:    0    0    0    0    0    0    0    0
+
+SWM, SWR, SWL: Middle, Right, and Left button states
+
+Touchpad 1 Finger packet (APD = 0x0):
+
+           b7   b6   b5   b4   b3   b2   b1   b0
+ byte 0:  SWM  SWR  SWL    1    1   X2   X1   X0
+ byte 1:   X9   X8   X7    1   X6   X5   X4   X3
+ byte 2:    0  X11  X10  LFB   Y3   Y2   Y1   Y0
+ byte 3:   Y5   Y4    0    0    1 TAPF2 TAPF1 TAPF0
+ byte 4:  Zv7  Y11  Y10    1   Y9   Y8   Y7   Y6
+ byte 5:  Zv6  Zv5  Zv4    0  Zv3  Zv2  Zv1  Zv0
+
+TAPF: ???
+LFB:  ???
+
+Touchpad 2 Finger packet (APD = 0x1):
+
+           b7   b6   b5   b4   b3   b2   b1   b0
+ byte 0:  SWM  SWR  SWL    1    1  AX6  AX5  AX4
+ byte 1: AX11 AX10  AX9  AX8  AX7  AZ1  AY4  AZ0
+ byte 2: AY11 AY10  AY9  CONT AY8  AY7  AY6  AY5
+ byte 3:    0    0    0    1    1  BX6  BX5  BX4
+ byte 4: BX11 BX10  BX9  BX8  BX7  BZ1  BY4  BZ0
+ byte 5: BY11 BY10  BY9    0  BY8  BY7  BY5  BY5
+
+CONT: A 3-or-4 Finger packet is to follow
+
+Touchpad 3-or-4 Finger packet (APD = 0x3):
+
+           b7   b6   b5   b4   b3   b2   b1   b0
+ byte 0:  SWM  SWR  SWL    1    1  AX6  AX5  AX4
+ byte 1: AX11 AX10  AX9  AX8  AX7  AZ1  AY4  AZ0
+ byte 2: AY11 AY10  AY9  OVF  AY8  AY7  AY6  AY5
+ byte 3:    0    0    1    1    1  BX6  BX5  BX4
+ byte 4: BX11 BX10  BX9  BX8  BX7  BZ1  BY4  BZ0
+ byte 5: BY11 BY10  BY9    0  BY8  BY7  BY5  BY5
+
+OVF: 5th finger detected

Documentation/kernel-parameters.txt

@@ -1511,7 +1511,14 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 	i8042.nopnp	[HW] Don't use ACPIPnP / PnPBIOS to discover KBD/AUX
 			     controllers
 	i8042.notimeout	[HW] Ignore timeout condition signalled by controller
-	i8042.reset	[HW] Reset the controller during init and cleanup
+	i8042.reset	[HW] Reset the controller during init, cleanup and
+			     suspend-to-ram transitions, only during s2r
+			     transitions, or never reset
+			Format: { 1 | Y | y | 0 | N | n }
+			1, Y, y: always reset controller
+			0, N, n: don't ever reset controller
+			Default: only on s2r transitions on x86; most other
+			architectures force reset to be always executed
 	i8042.unlock	[HW] Unlock (ignore) the keylock
 	i8042.kbdreset  [HW] Reset device connected to KBD port
 

MAINTAINERS

@@ -7829,6 +7829,13 @@ F:	Documentation/scsi/megaraid.txt
 F:	drivers/scsi/megaraid.*
 F:	drivers/scsi/megaraid/
 
+MELFAS MIP4 TOUCHSCREEN DRIVER
+M:	Sangwon Jee <jeesw@melfas.com>
+W:	http://www.melfas.com
+S:	Supported
+F:	drivers/input/touchscreen/melfas_mip4.c
+F:	Documentation/devicetree/bindings/input/touchscreen/melfas_mip4.txt
+
 MELLANOX ETHERNET DRIVER (mlx4_en)
 M:	Tariq Toukan <tariqt@mellanox.com>
 L:	netdev@vger.kernel.org

drivers/input/mouse/alps.c

@@ -103,6 +103,7 @@ static const struct alps_nibble_commands alps_v6_nibble_commands[] = {
 					   6-byte ALPS packet */
 #define ALPS_STICK_BITS		0x100	/* separate stick button bits */
 #define ALPS_BUTTONPAD		0x200	/* device is a clickpad */
+#define ALPS_DUALPOINT_WITH_PRESSURE	0x400	/* device can report trackpoint pressure */
 
 static const struct alps_model_info alps_model_data[] = {
 	{ { 0x32, 0x02, 0x14 }, 0x00, { ALPS_PROTO_V2, 0xf8, 0xf8, ALPS_PASS | ALPS_DUALPOINT } },	/* Toshiba Salellite Pro M10 */
@@ -1156,15 +1157,28 @@ static unsigned char alps_get_pkt_id_ss4_v2(unsigned char *byte)
 {
 	unsigned char pkt_id = SS4_PACKET_ID_IDLE;
 
+	switch (byte[3] & 0x30) {
+	case 0x00:
 		if (byte[0] == 0x18 && byte[1] == 0x10 && byte[2] == 0x00 &&
-	    (byte[3] & 0x88) == 0x08 && byte[4] == 0x10 && byte[5] == 0x00) {
+		    (byte[3] & 0x88) == 0x08 && byte[4] == 0x10 &&
+		    byte[5] == 0x00) {
 			pkt_id = SS4_PACKET_ID_IDLE;
-	} else if (!(byte[3] & 0x10)) {
+		} else {
 			pkt_id = SS4_PACKET_ID_ONE;
-	} else if (!(byte[3] & 0x20)) {
+		}
+		break;
+	case 0x10:
+		/* two-finger finger positions */
 		pkt_id = SS4_PACKET_ID_TWO;
-	} else {
+		break;
+	case 0x20:
+		/* stick pointer */
+		pkt_id = SS4_PACKET_ID_STICK;
+		break;
+	case 0x30:
+		/* third and fourth finger positions */
 		pkt_id = SS4_PACKET_ID_MULTI;
+		break;
 	}
 
 	return pkt_id;
@@ -1185,7 +1199,13 @@ static int alps_decode_ss4_v2(struct alps_fields *f,
 		f->mt[0].x = SS4_1F_X_V2(p);
 		f->mt[0].y = SS4_1F_Y_V2(p);
 		f->pressure = ((SS4_1F_Z_V2(p)) * 2) & 0x7f;
-		f->fingers = 1;
+		/*
+		 * When a button is held the device will give us events
+		 * with x, y, and pressure of 0. This causes annoying jumps
+		 * if a touch is released while the button is held.
+		 * Handle this by claiming zero contacts.
+		 */
+		f->fingers = f->pressure > 0 ? 1 : 0;
 		f->first_mp = 0;
 		f->is_mp = 0;
 		break;
@@ -1246,17 +1266,41 @@ static int alps_decode_ss4_v2(struct alps_fields *f,
 		}
 		break;
 
+	case SS4_PACKET_ID_STICK:
+		if (!(priv->flags & ALPS_DUALPOINT)) {
+			psmouse_warn(psmouse,
+				     "Rejected trackstick packet from non DualPoint device");
+		} else {
+			int x = (s8)(((p[0] & 1) << 7) | (p[1] & 0x7f));
+			int y = (s8)(((p[3] & 1) << 7) | (p[2] & 0x7f));
+			int pressure = (s8)(p[4] & 0x7f);
+
+			input_report_rel(priv->dev2, REL_X, x);
+			input_report_rel(priv->dev2, REL_Y, -y);
+			input_report_abs(priv->dev2, ABS_PRESSURE, pressure);
+		}
+		break;
+
 	case SS4_PACKET_ID_IDLE:
 	default:
 		memset(f, 0, sizeof(struct alps_fields));
 		break;
 	}
 
+	/* handle buttons */
+	if (pkt_id == SS4_PACKET_ID_STICK) {
+		f->ts_left = !!(SS4_BTN_V2(p) & 0x01);
+		if (!(priv->flags & ALPS_BUTTONPAD)) {
+			f->ts_right = !!(SS4_BTN_V2(p) & 0x02);
+			f->ts_middle = !!(SS4_BTN_V2(p) & 0x04);
+		}
+	} else {
 		f->left = !!(SS4_BTN_V2(p) & 0x01);
 		if (!(priv->flags & ALPS_BUTTONPAD)) {
 			f->right = !!(SS4_BTN_V2(p) & 0x02);
 			f->middle = !!(SS4_BTN_V2(p) & 0x04);
 		}
+	}
 
 	return 0;
 }
@@ -1266,6 +1310,7 @@ static void alps_process_packet_ss4_v2(struct psmouse *psmouse)
 	struct alps_data *priv = psmouse->private;
 	unsigned char *packet = psmouse->packet;
 	struct input_dev *dev = psmouse->dev;
+	struct input_dev *dev2 = priv->dev2;
 	struct alps_fields *f = &priv->f;
 
 	memset(f, 0, sizeof(struct alps_fields));
@@ -1311,6 +1356,13 @@ static void alps_process_packet_ss4_v2(struct psmouse *psmouse)
 
 	input_report_abs(dev, ABS_PRESSURE, f->pressure);
 	input_sync(dev);
+
+	if (priv->flags & ALPS_DUALPOINT) {
+		input_report_key(dev2, BTN_LEFT, f->ts_left);
+		input_report_key(dev2, BTN_RIGHT, f->ts_right);
+		input_report_key(dev2, BTN_MIDDLE, f->ts_middle);
+		input_sync(dev2);
+	}
 }
 
 static bool alps_is_valid_package_ss4_v2(struct psmouse *psmouse)
@@ -2695,6 +2747,10 @@ static int alps_set_protocol(struct psmouse *psmouse,
 		if (alps_set_defaults_ss4_v2(psmouse, priv))
 			return -EIO;
 
+		if (priv->fw_ver[1] == 0x1)
+			priv->flags |= ALPS_DUALPOINT |
+					ALPS_DUALPOINT_WITH_PRESSURE;
+
 		break;
 	}
 
@@ -2767,6 +2823,9 @@ static int alps_identify(struct psmouse *psmouse, struct alps_data *priv)
 		} else if (e7[0] == 0x73 && e7[1] == 0x03 &&
 			   e7[2] == 0x14 && ec[1] == 0x02) {
 			protocol = &alps_v8_protocol_data;
+		} else if (e7[0] == 0x73 && e7[1] == 0x03 &&
+			   e7[2] == 0x28 && ec[1] == 0x01) {
+			protocol = &alps_v8_protocol_data;
 		} else {
 			psmouse_dbg(psmouse,
 				    "Likely not an ALPS touchpad: E7=%3ph, EC=%3ph\n", e7, ec);
@@ -2949,6 +3008,10 @@ int alps_init(struct psmouse *psmouse)
 
 		input_set_capability(dev2, EV_REL, REL_X);
 		input_set_capability(dev2, EV_REL, REL_Y);
+		if (priv->flags & ALPS_DUALPOINT_WITH_PRESSURE) {
+			input_set_capability(dev2, EV_ABS, ABS_PRESSURE);
+			input_set_abs_params(dev2, ABS_PRESSURE, 0, 127, 0, 0);
+		}
 		input_set_capability(dev2, EV_KEY, BTN_LEFT);
 		input_set_capability(dev2, EV_KEY, BTN_RIGHT);
 		input_set_capability(dev2, EV_KEY, BTN_MIDDLE);

drivers/input/mouse/alps.h

@@ -37,12 +37,14 @@
  *  or there's button activities.
  * SS4_PACKET_ID_TWO: There's two or more fingers on touchpad
  * SS4_PACKET_ID_MULTI: There's three or more fingers on touchpad
+ * SS4_PACKET_ID_STICK: A stick pointer packet
 */
 enum SS4_PACKET_ID {
 	SS4_PACKET_ID_IDLE = 0,
 	SS4_PACKET_ID_ONE,
 	SS4_PACKET_ID_TWO,
 	SS4_PACKET_ID_MULTI,
+	SS4_PACKET_ID_STICK,
 };
 
 #define SS4_COUNT_PER_ELECTRODE		256

drivers/input/mouse/elantech.c

@@ -1134,7 +1134,7 @@ static int elantech_get_resolution_v4(struct psmouse *psmouse,
  * System76 Pangolin       0x250f01        ?               2 hw buttons
  * (*) + 3 trackpoint buttons
  * (**) + 0 trackpoint buttons
- * Note: Lenovo L430 and Lenovo L430 have the same fw_version/caps
+ * Note: Lenovo L430 and Lenovo L530 have the same fw_version/caps
  */
 static void elantech_set_buttonpad_prop(struct psmouse *psmouse)
 {
@@ -1159,6 +1159,13 @@ static const struct dmi_system_id elantech_dmi_has_middle_button[] = {
 			DMI_MATCH(DMI_PRODUCT_NAME, "CELSIUS H730"),
 		},
 	},
+	{
+		/* Fujitsu H760 also has a middle button */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "CELSIUS H760"),
+		},
+	},
 #endif
 	{ }
 };
@@ -1503,10 +1510,10 @@ static const struct dmi_system_id elantech_dmi_force_crc_enabled[] = {
 		},
 	},
 	{
-		/* Fujitsu LIFEBOOK E554  does not work with crc_enabled == 0 */
+		/* Fujitsu H760 does not work with crc_enabled == 0 */
 		.matches = {
 			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
-			DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK E554"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "CELSIUS H760"),
 		},
 	},
 	{
@@ -1516,6 +1523,20 @@ static const struct dmi_system_id elantech_dmi_force_crc_enabled[] = {
 			DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK E544"),
 		},
 	},
+	{
+		/* Fujitsu LIFEBOOK E554  does not work with crc_enabled == 0 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK E554"),
+		},
+	},
+	{
+		/* Fujitsu LIFEBOOK E556 does not work with crc_enabled == 0 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK E556"),
+		},
+	},
 	{
 		/* Fujitsu LIFEBOOK U745 does not work with crc_enabled == 0 */
 		.matches = {

drivers/input/rmi4/rmi_i2c.c

@@ -221,6 +221,21 @@ static const struct of_device_id rmi_i2c_of_match[] = {
 MODULE_DEVICE_TABLE(of, rmi_i2c_of_match);
 #endif
 
+static void rmi_i2c_regulator_bulk_disable(void *data)
+{
+	struct rmi_i2c_xport *rmi_i2c = data;
+
+	regulator_bulk_disable(ARRAY_SIZE(rmi_i2c->supplies),
+			       rmi_i2c->supplies);
+}
+
+static void rmi_i2c_unregister_transport(void *data)
+{
+	struct rmi_i2c_xport *rmi_i2c = data;
+
+	rmi_unregister_transport_device(&rmi_i2c->xport);
+}
+
 static int rmi_i2c_probe(struct i2c_client *client,
 			 const struct i2c_device_id *id)
 {
@@ -264,6 +279,12 @@ static int rmi_i2c_probe(struct i2c_client *client,
 	if (retval < 0)
 		return retval;
 
+	retval = devm_add_action_or_reset(&client->dev,
+					  rmi_i2c_regulator_bulk_disable,
+					  rmi_i2c);
+	if (retval)
+		return retval;
+
 	of_property_read_u32(client->dev.of_node, "syna,startup-delay-ms",
 			     &rmi_i2c->startup_delay);
 
@@ -294,6 +315,11 @@ static int rmi_i2c_probe(struct i2c_client *client,
 			client->addr);
 		return retval;
 	}
+	retval = devm_add_action_or_reset(&client->dev,
+					  rmi_i2c_unregister_transport,
+					  rmi_i2c);
+	if (retval)
+		return retval;
 
 	retval = rmi_i2c_init_irq(client);
 	if (retval < 0)
@@ -304,17 +330,6 @@ static int rmi_i2c_probe(struct i2c_client *client,
 	return 0;
 }
 
-static int rmi_i2c_remove(struct i2c_client *client)
-{
-	struct rmi_i2c_xport *rmi_i2c = i2c_get_clientdata(client);
-
-	rmi_unregister_transport_device(&rmi_i2c->xport);
-	regulator_bulk_disable(ARRAY_SIZE(rmi_i2c->supplies),
-			       rmi_i2c->supplies);
-
-	return 0;
-}
-
 #ifdef CONFIG_PM_SLEEP
 static int rmi_i2c_suspend(struct device *dev)
 {
@@ -431,7 +446,6 @@ static struct i2c_driver rmi_i2c_driver = {
 	},
 	.id_table	= rmi_id,
 	.probe		= rmi_i2c_probe,
-	.remove		= rmi_i2c_remove,
 };
 
 module_i2c_driver(rmi_i2c_driver);

drivers/input/rmi4/rmi_spi.c

@@ -396,6 +396,13 @@ static inline int rmi_spi_of_probe(struct spi_device *spi,
 }
 #endif
 
+static void rmi_spi_unregister_transport(void *data)
+{
+	struct rmi_spi_xport *rmi_spi = data;
+
+	rmi_unregister_transport_device(&rmi_spi->xport);
+}
+
 static int rmi_spi_probe(struct spi_device *spi)
 {
 	struct rmi_spi_xport *rmi_spi;
@@ -464,6 +471,11 @@ static int rmi_spi_probe(struct spi_device *spi)
 		dev_err(&spi->dev, "failed to register transport.\n");
 		return retval;
 	}
+	retval = devm_add_action_or_reset(&spi->dev,
+					  rmi_spi_unregister_transport,
+					  rmi_spi);
+	if (retval)
+		return retval;
 
 	retval = rmi_spi_init_irq(spi);
 	if (retval < 0)
@@ -473,15 +485,6 @@ static int rmi_spi_probe(struct spi_device *spi)
 	return 0;
 }
 
-static int rmi_spi_remove(struct spi_device *spi)
-{
-	struct rmi_spi_xport *rmi_spi = spi_get_drvdata(spi);
-
-	rmi_unregister_transport_device(&rmi_spi->xport);
-
-	return 0;
-}
-
 #ifdef CONFIG_PM_SLEEP
 static int rmi_spi_suspend(struct device *dev)
 {
@@ -577,7 +580,6 @@ static struct spi_driver rmi_spi_driver = {
 	},
 	.id_table	= rmi_id,
 	.probe		= rmi_spi_probe,
-	.remove		= rmi_spi_remove,
 };
 
 module_spi_driver(rmi_spi_driver);

drivers/input/serio/i8042-io.h

@@ -81,7 +81,7 @@ static inline int i8042_platform_init(void)
 		return -EBUSY;
 #endif
 
-	i8042_reset = 1;
+	i8042_reset = I8042_RESET_ALWAYS;
 	return 0;
 }
 

drivers/input/serio/i8042-ip22io.h

@@ -61,7 +61,7 @@ static inline int i8042_platform_init(void)
 		return -EBUSY;
 #endif
 
-	i8042_reset = 1;
+	i8042_reset = I8042_RESET_ALWAYS;
 
 	return 0;
 }

drivers/input/serio/i8042-ppcio.h

@@ -44,7 +44,7 @@ static inline void i8042_write_command(int val)
 
 static inline int i8042_platform_init(void)
 {
-	i8042_reset = 1;
+	i8042_reset = I8042_RESET_ALWAYS;
 	return 0;
 }
 

drivers/input/serio/i8042-sparcio.h

@@ -130,7 +130,7 @@ static int __init i8042_platform_init(void)
 		}
 	}
 
-	i8042_reset = 1;
+	i8042_reset = I8042_RESET_ALWAYS;
 
 	return 0;
 }

drivers/input/serio/i8042-unicore32io.h

@@ -61,7 +61,7 @@ static inline int i8042_platform_init(void)
 	if (!request_mem_region(I8042_REGION_START, I8042_REGION_SIZE, "i8042"))
 		return -EBUSY;
 
-	i8042_reset = 1;
+	i8042_reset = I8042_RESET_ALWAYS;
 	return 0;
 }
 

drivers/input/serio/i8042-x86ia64io.h

@@ -510,6 +510,90 @@ static const struct dmi_system_id __initconst i8042_dmi_nomux_table[] = {
 	{ }
 };
 
+/*
+ * On some Asus laptops, just running self tests cause problems.
+ */
+static const struct dmi_system_id i8042_dmi_noselftest_table[] = {
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "A455LD"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "K401LB"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "K501LB"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "K501LX"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "R409L"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "V502LX"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "X302LA"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "X450LCP"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "X450LD"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "X455LAB"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "X455LDB"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "X455LF"),
+		},
+	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Z450LA"),
+		},
+	},
+	{ }
+};
 static const struct dmi_system_id __initconst i8042_dmi_reset_table[] = {
 	{
 		/* MSI Wind U-100 */
@@ -1072,12 +1156,18 @@ static int __init i8042_platform_init(void)
 		return retval;
 
 #if defined(__ia64__)
-        i8042_reset = true;
+        i8042_reset = I8042_RESET_ALWAYS;
 #endif
 
 #ifdef CONFIG_X86
+	/* Honor module parameter when value is not default */
+	if (i8042_reset == I8042_RESET_DEFAULT) {
 		if (dmi_check_system(i8042_dmi_reset_table))
-		i8042_reset = true;
+			i8042_reset = I8042_RESET_ALWAYS;
+
+		if (dmi_check_system(i8042_dmi_noselftest_table))
+			i8042_reset = I8042_RESET_NEVER;
+	}
 
 	if (dmi_check_system(i8042_dmi_noloop_table))
 		i8042_noloop = true;

drivers/input/serio/i8042.c

@@ -48,9 +48,39 @@ static bool i8042_unlock;
 module_param_named(unlock, i8042_unlock, bool, 0);
 MODULE_PARM_DESC(unlock, "Ignore keyboard lock.");
 
-static bool i8042_reset;
-module_param_named(reset, i8042_reset, bool, 0);
-MODULE_PARM_DESC(reset, "Reset controller during init and cleanup.");
+enum i8042_controller_reset_mode {
+	I8042_RESET_NEVER,
+	I8042_RESET_ALWAYS,
+	I8042_RESET_ON_S2RAM,
+#define I8042_RESET_DEFAULT	I8042_RESET_ON_S2RAM
+};
+static enum i8042_controller_reset_mode i8042_reset = I8042_RESET_DEFAULT;
+static int i8042_set_reset(const char *val, const struct kernel_param *kp)
+{
+	enum i8042_controller_reset_mode *arg = kp->arg;
+	int error;
+	bool reset;
+
+	if (val) {
+		error = kstrtobool(val, &reset);
+		if (error)
+			return error;
+	} else {
+		reset = true;
+	}
+
+	*arg = reset ? I8042_RESET_ALWAYS : I8042_RESET_NEVER;
+	return 0;
+}
+
+static const struct kernel_param_ops param_ops_reset_param = {
+	.flags = KERNEL_PARAM_OPS_FL_NOARG,
+	.set = i8042_set_reset,
+};
+#define param_check_reset_param(name, p)	\
+	__param_check(name, p, enum i8042_controller_reset_mode)
+module_param_named(reset, i8042_reset, reset_param, 0);
+MODULE_PARM_DESC(reset, "Reset controller on resume, cleanup or both");
 
 static bool i8042_direct;
 module_param_named(direct, i8042_direct, bool, 0);
@@ -1019,7 +1049,7 @@ static int i8042_controller_init(void)
  * Reset the controller and reset CRT to the original value set by BIOS.
  */
 
-static void i8042_controller_reset(bool force_reset)
+static void i8042_controller_reset(bool s2r_wants_reset)
 {
 	i8042_flush();
 
@@ -1044,8 +1074,10 @@ static void i8042_controller_reset(bool force_reset)
  * Reset the controller if requested.
  */
 
-	if (i8042_reset || force_reset)
+	if (i8042_reset == I8042_RESET_ALWAYS ||
+	    (i8042_reset == I8042_RESET_ON_S2RAM && s2r_wants_reset)) {
 		i8042_controller_selftest();
+	}
 
 /*
  * Restore the original control register setting.
@@ -1110,7 +1142,7 @@ static void i8042_dritek_enable(void)
  * before suspending.
  */
 
-static int i8042_controller_resume(bool force_reset)
+static int i8042_controller_resume(bool s2r_wants_reset)
 {
 	int error;
 
@@ -1118,7 +1150,8 @@ static int i8042_controller_resume(bool force_reset)
 	if (error)
 		return error;
 
-	if (i8042_reset || force_reset) {
+	if (i8042_reset == I8042_RESET_ALWAYS ||
+	    (i8042_reset == I8042_RESET_ON_S2RAM && s2r_wants_reset)) {
 		error = i8042_controller_selftest();
 		if (error)
 			return error;
@@ -1195,7 +1228,7 @@ static int i8042_pm_resume_noirq(struct device *dev)
 
 static int i8042_pm_resume(struct device *dev)
 {
-	bool force_reset;
+	bool want_reset;
 	int i;
 
 	for (i = 0; i < I8042_NUM_PORTS; i++) {
@@ -1218,9 +1251,9 @@ static int i8042_pm_resume(struct device *dev)
 	 * off control to the platform firmware, otherwise we can simply restore
 	 * the mode.
 	 */
-	force_reset = pm_resume_via_firmware();
+	want_reset = pm_resume_via_firmware();
 
-	return i8042_controller_resume(force_reset);
+	return i8042_controller_resume(want_reset);
 }
 
 static int i8042_pm_thaw(struct device *dev)
@@ -1482,7 +1515,7 @@ static int __init i8042_probe(struct platform_device *dev)
 
 	i8042_platform_device = dev;
 
-	if (i8042_reset) {
+	if (i8042_reset == I8042_RESET_ALWAYS) {
 		error = i8042_controller_selftest();
 		if (error)
 			return error;

drivers/input/touchscreen/melfas_mip4.c

@@ -157,6 +157,7 @@ struct mip4_ts {
 
 	char phys[32];
 	char product_name[16];
+	char ic_name[4];
 
 	unsigned int max_x;
 	unsigned int max_y;
@@ -263,6 +264,18 @@ static int mip4_query_device(struct mip4_ts *ts)
 		dev_dbg(&ts->client->dev, "product name: %.*s\n",
 			(int)sizeof(ts->product_name), ts->product_name);
 
+	/* IC name */
+	cmd[0] = MIP4_R0_INFO;
+	cmd[1] = MIP4_R1_INFO_IC_NAME;
+	error = mip4_i2c_xfer(ts, cmd, sizeof(cmd),
+			      ts->ic_name, sizeof(ts->ic_name));
+	if (error)
+		dev_warn(&ts->client->dev,
+			 "Failed to retrieve IC name: %d\n", error);
+	else
+		dev_dbg(&ts->client->dev, "IC name: %.*s\n",
+			(int)sizeof(ts->ic_name), ts->ic_name);
+
 	/* Firmware version */
 	error = mip4_get_fw_version(ts);
 	if (error)
@@ -1335,9 +1348,30 @@ static ssize_t mip4_sysfs_read_hw_version(struct device *dev,
 
 static DEVICE_ATTR(hw_version, S_IRUGO, mip4_sysfs_read_hw_version, NULL);
 
+static ssize_t mip4_sysfs_read_ic_name(struct device *dev,
+					  struct device_attribute *attr,
+					  char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct mip4_ts *ts = i2c_get_clientdata(client);
+	size_t count;
+
+	mutex_lock(&ts->input->mutex);
+
+	count = snprintf(buf, PAGE_SIZE, "%.*s\n",
+			 (int)sizeof(ts->ic_name), ts->ic_name);
+
+	mutex_unlock(&ts->input->mutex);
+
+	return count;
+}
+
+static DEVICE_ATTR(ic_name, S_IRUGO, mip4_sysfs_read_ic_name, NULL);
+
 static struct attribute *mip4_attrs[] = {
 	&dev_attr_fw_version.attr,
 	&dev_attr_hw_version.attr,
+	&dev_attr_ic_name.attr,
 	&dev_attr_update_fw.attr,
 	NULL,
 };
@@ -1538,6 +1572,6 @@ static struct i2c_driver mip4_driver = {
 module_i2c_driver(mip4_driver);
 
 MODULE_DESCRIPTION("MELFAS MIP4 Touchscreen");
-MODULE_VERSION("2016.03.12");
+MODULE_VERSION("2016.09.28");
 MODULE_AUTHOR("Sangwon Jee <jeesw@melfas.com>");
 MODULE_LICENSE("GPL");