Blackfin: bf527-ezkit: add support for V2.1 boards

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

arch/blackfin/Kconfig

@@ -349,7 +349,7 @@ config MEM_MT48LC8M32B2B5_7
 
 config MEM_MT48LC32M16A2TG_75
 	bool
-	depends on (BFIN527_EZKIT || BFIN532_IP0X || BLACKSTAMP)
+	depends on (BFIN527_EZKIT || BFIN527_EZKIT_V2 || BFIN532_IP0X || BLACKSTAMP)
 	default y
 
 config MEM_MT48LC32M8A2_75
@@ -448,7 +448,7 @@ config VCO_MULT
 	range 1 64
 	default "22" if BFIN533_EZKIT
 	default "45" if BFIN533_STAMP
-	default "20" if (BFIN537_STAMP || BFIN527_EZKIT || BFIN548_EZKIT || BFIN548_BLUETECHNIX_CM || BFIN538_EZKIT)
+	default "20" if (BFIN537_STAMP || BFIN527_EZKIT || BFIN527_EZKIT_V2 || BFIN548_EZKIT || BFIN548_BLUETECHNIX_CM || BFIN538_EZKIT)
 	default "22" if BFIN533_BLUETECHNIX_CM
 	default "20" if (BFIN537_BLUETECHNIX_CM_E || BFIN537_BLUETECHNIX_CM_U || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM)
 	default "20" if BFIN561_EZKIT

arch/blackfin/mach-bf527/boards/Kconfig

@@ -9,6 +9,11 @@ config BFIN527_EZKIT
 	help
 	  BF527-EZKIT-LITE board support.
 
+config BFIN527_EZKIT_V2
+	bool "BF527-EZKIT-V2"
+	help
+	  BF527-EZKIT-LITE V2.1+ board support.
+
 config BFIN527_BLUETECHNIX_CM
 	bool "Bluetechnix CM-BF527"
 	help

arch/blackfin/mach-bf527/boards/Makefile

@@ -3,5 +3,6 @@
 #
 
 obj-$(CONFIG_BFIN527_EZKIT)            += ezkit.o
+obj-$(CONFIG_BFIN527_EZKIT_V2)         += ezkit.o
 obj-$(CONFIG_BFIN527_BLUETECHNIX_CM)   += cm_bf527.o
 obj-$(CONFIG_BFIN526_EZBRD)            += ezbrd.o

arch/blackfin/mach-bf527/boards/ezkit.c

@@ -18,6 +18,8 @@
 #include <linux/interrupt.h>
 #include <linux/usb/sl811.h>
 #include <linux/usb/musb.h>
+#include <linux/leds.h>
+#include <linux/input.h>
 #include <asm/dma.h>
 #include <asm/bfin5xx_spi.h>
 #include <asm/reboot.h>
@@ -29,7 +31,11 @@
 /*
  * Name the Board for the /proc/cpuinfo
  */
+#ifdef CONFIG_BFIN527_EZKIT_V2
+const char bfin_board_name[] = "ADI BF527-EZKIT V2";
+#else
 const char bfin_board_name[] = "ADI BF527-EZKIT";
+#endif
 
 /*
  *  Driver needs to know address, irq and flag pin.
@@ -143,6 +149,32 @@ static struct platform_device bf52x_t350mcqb_device = {
 };
 #endif
 
+#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+#include <asm/bfin-lq035q1.h>
+
+static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
+	.mode = LQ035_NORM | LQ035_RGB | LQ035_RL | LQ035_TB,
+};
+
+static struct resource bfin_lq035q1_resources[] = {
+	{
+		.start = IRQ_PPI_ERROR,
+		.end = IRQ_PPI_ERROR,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_lq035q1_device = {
+	.name		= "bfin-lq035q1",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(bfin_lq035q1_resources),
+	.resource	= bfin_lq035q1_resources,
+	.dev		= {
+		.platform_data = &bfin_lq035q1_data,
+	},
+};
+#endif
+
 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
 static struct mtd_partition ezkit_partitions[] = {
 	{
@@ -500,16 +532,15 @@ static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
-	 && defined(CONFIG_SND_SOC_WM8731_SPI)
-static struct bfin5xx_spi_chip spi_wm8731_chip_info = {
+#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+static struct bfin5xx_spi_chip spidev_chip_info = {
 	.enable_dma = 0,
-	.bits_per_word = 16,
+	.bits_per_word = 8,
 };
 #endif
 
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
-static struct bfin5xx_spi_chip spidev_chip_info = {
+#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
 	.enable_dma	= 0,
 	.bits_per_word	= 8,
 };
@@ -586,17 +617,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.mode = SPI_CPHA | SPI_CPOL,
 	},
 #endif
-#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
-	 && defined(CONFIG_SND_SOC_WM8731_SPI)
-	{
-		.modalias	= "wm8731",
-		.max_speed_hz	= 3125000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num	= 0,
-		.chip_select    = 5,
-		.controller_data = &spi_wm8731_chip_info,
-		.mode = SPI_MODE_0,
-	},
-#endif
 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 	{
 		.modalias = "spidev",
@@ -606,6 +626,16 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.controller_data = &spidev_chip_info,
 	},
 #endif
+#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+	{
+		.modalias = "bfin-lq035q1-spi",
+		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 7,
+		.controller_data = &lq035q1_spi_chip_info,
+		.mode = SPI_CPHA | SPI_CPOL,
+	},
+#endif
 };
 
 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
@@ -824,6 +854,71 @@ static struct platform_device i2c_bfin_twi_device = {
 };
 #endif
 
+#if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
+#include <linux/mfd/adp5520.h>
+
+	/*
+	 *  ADP5520/5501 LEDs Data
+	 */
+
+static struct led_info adp5520_leds[] = {
+	{
+		.name = "adp5520-led1",
+		.default_trigger = "none",
+		.flags = FLAG_ID_ADP5520_LED1_ADP5501_LED0 | ADP5520_LED_OFFT_600ms,
+	},
+};
+
+static struct adp5520_leds_platform_data adp5520_leds_data = {
+	.num_leds = ARRAY_SIZE(adp5520_leds),
+	.leds = adp5520_leds,
+	.fade_in = ADP5520_FADE_T_600ms,
+	.fade_out = ADP5520_FADE_T_600ms,
+	.led_on_time = ADP5520_LED_ONT_600ms,
+};
+
+	/*
+	 *  ADP5520 Keypad Data
+	 */
+
+static const unsigned short adp5520_keymap[ADP5520_KEYMAPSIZE] = {
+	[ADP5520_KEY(3, 3)]	= KEY_1,
+	[ADP5520_KEY(2, 3)]	= KEY_2,
+	[ADP5520_KEY(1, 3)]	= KEY_3,
+	[ADP5520_KEY(0, 3)]	= KEY_UP,
+	[ADP5520_KEY(3, 2)]	= KEY_4,
+	[ADP5520_KEY(2, 2)]	= KEY_5,
+	[ADP5520_KEY(1, 2)]	= KEY_6,
+	[ADP5520_KEY(0, 2)]	= KEY_DOWN,
+	[ADP5520_KEY(3, 1)]	= KEY_7,
+	[ADP5520_KEY(2, 1)]	= KEY_8,
+	[ADP5520_KEY(1, 1)]	= KEY_9,
+	[ADP5520_KEY(0, 1)]	= KEY_DOT,
+	[ADP5520_KEY(3, 0)]	= KEY_BACKSPACE,
+	[ADP5520_KEY(2, 0)]	= KEY_0,
+	[ADP5520_KEY(1, 0)]	= KEY_HELP,
+	[ADP5520_KEY(0, 0)]	= KEY_ENTER,
+};
+
+static struct adp5520_keys_platform_data adp5520_keys_data = {
+	.rows_en_mask	= ADP5520_ROW_R3 | ADP5520_ROW_R2 | ADP5520_ROW_R1 | ADP5520_ROW_R0,
+	.cols_en_mask	= ADP5520_COL_C3 | ADP5520_COL_C2 | ADP5520_COL_C1 | ADP5520_COL_C0,
+	.keymap		= adp5520_keymap,
+	.keymapsize	= ARRAY_SIZE(adp5520_keymap),
+	.repeat		= 0,
+};
+
+	/*
+	 *  ADP5520/5501 Multifuction Device Init Data
+	 */
+
+static struct adp5520_platform_data adp5520_pdev_data = {
+	.leds = &adp5520_leds_data,
+	.keys = &adp5520_keys_data,
+};
+
+#endif
+
 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 #if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
 	{
@@ -841,6 +936,20 @@ static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 		I2C_BOARD_INFO("bfin-adv7393", 0x2B),
 	},
 #endif
+#if defined(CONFIG_TOUCHSCREEN_AD7879_I2C) || defined(CONFIG_TOUCHSCREEN_AD7879_I2C_MODULE)
+	{
+		I2C_BOARD_INFO("ad7879", 0x2C),
+		.irq = IRQ_PF8,
+		.platform_data = (void *)&bfin_ad7879_ts_info,
+	},
+#endif
+#if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
+	{
+		I2C_BOARD_INFO("pmic-adp5520", 0x32),
+		.irq = IRQ_PF9,
+		.platform_data = (void *)&adp5520_pdev_data,
+	},
+#endif
 };
 
 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
@@ -915,7 +1024,6 @@ static struct platform_device bfin_sport1_uart_device = {
 #endif
 
 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-#include <linux/input.h>
 #include <linux/gpio_keys.h>
 
 static struct gpio_keys_button bfin_gpio_keys_table[] = {
@@ -937,7 +1045,6 @@ static struct platform_device bfin_device_gpiokeys = {
 #endif
 
 #if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
-#include <linux/input.h>
 #include <asm/bfin_rotary.h>
 
 static struct bfin_rotary_platform_data bfin_rotary_data = {
@@ -1043,6 +1150,10 @@ static struct platform_device *stamp_devices[] __initdata = {
 	&bf52x_t350mcqb_device,
 #endif
 
+#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
+	&bfin_lq035q1_device,
+#endif
+
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,