ARM: vexpress: Motherboard RS1 memory map support

This patch adds support for RS1 memory map based Versatile Express
motherboard.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>

arch/arm/boot/dts/vexpress-v2m-rs1.dtsi

+/*
+ * ARM Ltd. Versatile Express
+ *
+ * Motherboard Express uATX
+ * V2M-P1
+ *
+ * HBI-0190D
+ *
+ * RS1 memory map ("ARM Cortex-A Series memory map" in the board's
+ * Technical Reference Manual)
+ *
+ * WARNING! The hardware described in this file is independent from the
+ * original variant (vexpress-v2m.dtsi), but there is a strong
+ * correspondence between the two configurations.
+ *
+ * TAKE CARE WHEN MAINTAINING THIS FILE TO PROPAGATE ANY RELEVANT
+ * CHANGES TO vexpress-v2m.dtsi!
+ */
+
+/ {
+	aliases {
+		arm,v2m_timer = &v2m_timer01;
+	};
+
+	motherboard {
+		compatible = "simple-bus";
+		arm,v2m-memory-map = "rs1";
+		#address-cells = <2>; /* SMB chipselect number and offset */
+		#size-cells = <1>;
+		#interrupt-cells = <1>;
+
+		flash@0,00000000 {
+			compatible = "arm,vexpress-flash", "cfi-flash";
+			reg = <0 0x00000000 0x04000000>,
+			      <4 0x00000000 0x04000000>;
+			bank-width = <4>;
+		};
+
+		psram@1,00000000 {
+			compatible = "arm,vexpress-psram", "mtd-ram";
+			reg = <1 0x00000000 0x02000000>;
+			bank-width = <4>;
+		};
+
+		vram@2,00000000 {
+			compatible = "arm,vexpress-vram";
+			reg = <2 0x00000000 0x00800000>;
+		};
+
+		ethernet@2,02000000 {
+			compatible = "smsc,lan9118", "smsc,lan9115";
+			reg = <2 0x02000000 0x10000>;
+			interrupts = <15>;
+			phy-mode = "mii";
+			reg-io-width = <4>;
+			smsc,irq-active-high;
+			smsc,irq-push-pull;
+		};
+
+		usb@2,03000000 {
+			compatible = "nxp,usb-isp1761";
+			reg = <2 0x03000000 0x20000>;
+			interrupts = <16>;
+			port1-otg;
+		};
+
+		iofpga@3,00000000 {
+			compatible = "arm,amba-bus", "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 3 0 0x200000>;
+
+			sysreg@010000 {
+				compatible = "arm,vexpress-sysreg";
+				reg = <0x010000 0x1000>;
+			};
+
+			sysctl@020000 {
+				compatible = "arm,sp810", "arm,primecell";
+				reg = <0x020000 0x1000>;
+			};
+
+			/* PCI-E I2C bus */
+			v2m_i2c_pcie: i2c@030000 {
+				compatible = "arm,versatile-i2c";
+				reg = <0x030000 0x1000>;
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				pcie-switch@60 {
+					compatible = "idt,89hpes32h8";
+					reg = <0x60>;
+				};
+			};
+
+			aaci@040000 {
+				compatible = "arm,pl041", "arm,primecell";
+				reg = <0x040000 0x1000>;
+				interrupts = <11>;
+			};
+
+			mmci@050000 {
+				compatible = "arm,pl180", "arm,primecell";
+				reg = <0x050000 0x1000>;
+				interrupts = <9 10>;
+			};
+
+			kmi@060000 {
+				compatible = "arm,pl050", "arm,primecell";
+				reg = <0x060000 0x1000>;
+				interrupts = <12>;
+			};
+
+			kmi@070000 {
+				compatible = "arm,pl050", "arm,primecell";
+				reg = <0x070000 0x1000>;
+				interrupts = <13>;
+			};
+
+			v2m_serial0: uart@090000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0x090000 0x1000>;
+				interrupts = <5>;
+			};
+
+			v2m_serial1: uart@0a0000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0x0a0000 0x1000>;
+				interrupts = <6>;
+			};
+
+			v2m_serial2: uart@0b0000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0x0b0000 0x1000>;
+				interrupts = <7>;
+			};
+
+			v2m_serial3: uart@0c0000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0x0c0000 0x1000>;
+				interrupts = <8>;
+			};
+
+			wdt@0f0000 {
+				compatible = "arm,sp805", "arm,primecell";
+				reg = <0x0f0000 0x1000>;
+				interrupts = <0>;
+			};
+
+			v2m_timer01: timer@110000 {
+				compatible = "arm,sp804", "arm,primecell";
+				reg = <0x110000 0x1000>;
+				interrupts = <2>;
+			};
+
+			v2m_timer23: timer@120000 {
+				compatible = "arm,sp804", "arm,primecell";
+				reg = <0x120000 0x1000>;
+			};
+
+			/* DVI I2C bus */
+			v2m_i2c_dvi: i2c@160000 {
+				compatible = "arm,versatile-i2c";
+				reg = <0x160000 0x1000>;
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				dvi-transmitter@39 {
+					compatible = "sil,sii9022-tpi", "sil,sii9022";
+					reg = <0x39>;
+				};
+
+				dvi-transmitter@60 {
+					compatible = "sil,sii9022-cpi", "sil,sii9022";
+					reg = <0x60>;
+				};
+			};
+
+			rtc@170000 {
+				compatible = "arm,pl031", "arm,primecell";
+				reg = <0x170000 0x1000>;
+				interrupts = <4>;
+			};
+
+			compact-flash@1a0000 {
+				compatible = "arm,vexpress-cf", "ata-generic";
+				reg = <0x1a0000 0x100
+				       0x1a0100 0xf00>;
+				reg-shift = <2>;
+			};
+
+			clcd@1f0000 {
+				compatible = "arm,pl111", "arm,primecell";
+				reg = <0x1f0000 0x1000>;
+				interrupts = <14>;
+			};
+		};
+	};
+};

arch/arm/mach-vexpress/include/mach/debug-macro.S

@@ -10,12 +10,34 @@
  * published by the Free Software Foundation.
  */
 
+#define DEBUG_LL_PHYS_BASE		0x10000000
 #define DEBUG_LL_UART_OFFSET		0x00009000
 
+#define DEBUG_LL_PHYS_BASE_RS1		0x1c000000
+#define DEBUG_LL_UART_OFFSET_RS1	0x00090000
+
+#define DEBUG_LL_VIRT_BASE		0xf8000000
+
 		.macro	addruart,rp,rv,tmp
-		mov	\rp, #DEBUG_LL_UART_OFFSET
-		orr	\rv, \rp, #0xf8000000	@ virtual base
-		orr	\rp, \rp, #0x10000000	@ physical base
+
+		@ Make an educated guess regarding the memory map:
+		@ - the original A9 core tile, which has MPCore peripherals
+		@   located at 0x1e000000, should use UART at 0x10009000
+		@ - all other (RS1 complaint) tiles use UART mapped
+		@   at 0x1c090000
+		mrc	p15, 4, \tmp, c15, c0, 0
+		cmp	\tmp, #0x1e000000
+
+		@ Original memory map
+		moveq	\rp, #DEBUG_LL_UART_OFFSET
+		orreq	\rv, \rp, #DEBUG_LL_VIRT_BASE
+		orreq	\rp, \rp, #DEBUG_LL_PHYS_BASE
+
+		@ RS1 memory map
+		movne	\rp, #DEBUG_LL_UART_OFFSET_RS1
+		orrne	\rv, \rp, #DEBUG_LL_VIRT_BASE
+		orrne	\rp, \rp, #DEBUG_LL_PHYS_BASE_RS1
+
 		.endm
 
 #include <asm/hardware/debug-pl01x.S>

arch/arm/mach-vexpress/include/mach/uncompress.h

@@ -22,7 +22,27 @@
 #define AMBA_UART_CR(base)	(*(volatile unsigned char *)((base) + 0x30))
 #define AMBA_UART_FR(base)	(*(volatile unsigned char *)((base) + 0x18))
 
-#define get_uart_base()	(0x10000000 + 0x00009000)
+#define UART_BASE	0x10009000
+#define UART_BASE_RS1	0x1c090000
+
+static unsigned long get_uart_base(void)
+{
+	unsigned long mpcore_periph;
+
+	/*
+	 * Make an educated guess regarding the memory map:
+	 * - the original A9 core tile, which has MPCore peripherals
+	 *   located at 0x1e000000, should use UART at 0x10009000
+	 * - all other (RS1 complaint) tiles use UART mapped
+	 *   at 0x1c090000
+	 */
+	asm("mrc p15, 4, %0, c15, c0, 0" : "=r" (mpcore_periph));
+
+	if (mpcore_periph == 0x1e000000)
+		return UART_BASE;
+	else
+		return UART_BASE_RS1;
+}
 
 /*
  * This does not append a newline

arch/arm/mach-vexpress/v2m.c

@@ -486,8 +486,35 @@ MACHINE_END
 
 #if defined(CONFIG_ARCH_VEXPRESS_DT)
 
+static struct map_desc v2m_rs1_io_desc __initdata = {
+	.virtual	= V2M_PERIPH,
+	.pfn		= __phys_to_pfn(0x1c000000),
+	.length		= SZ_2M,
+	.type		= MT_DEVICE,
+};
+
+static int __init v2m_dt_scan_memory_map(unsigned long node, const char *uname,
+		int depth, void *data)
+{
+	const char **map = data;
+
+	if (strcmp(uname, "motherboard") != 0)
+		return 0;
+
+	*map = of_get_flat_dt_prop(node, "arm,v2m-memory-map", NULL);
+
+	return 1;
+}
+
 void __init v2m_dt_map_io(void)
 {
+	const char *map = NULL;
+
+	of_scan_flat_dt(v2m_dt_scan_memory_map, &map);
+
+	if (map && strcmp(map, "rs1") == 0)
+		iotable_init(&v2m_rs1_io_desc, 1);
+	else
 		iotable_init(v2m_io_desc, ARRAY_SIZE(v2m_io_desc));
 
 #if defined(CONFIG_SMP)
@@ -535,6 +562,35 @@ static struct clk_lookup v2m_dt_lookups[] = {
 		.dev_id		= "1001f000.clcd",
 		.clk		= &osc1_clk,
 	},
+	/* RS1 memory map */
+	{	/* PL180 MMCI */
+		.dev_id		= "mb:mmci", /* 1c050000.mmci */
+		.clk		= &osc2_clk,
+	}, {	/* PL050 KMI0 */
+		.dev_id		= "1c060000.kmi",
+		.clk		= &osc2_clk,
+	}, {	/* PL050 KMI1 */
+		.dev_id		= "1c070000.kmi",
+		.clk		= &osc2_clk,
+	}, {	/* PL011 UART0 */
+		.dev_id		= "1c090000.uart",
+		.clk		= &osc2_clk,
+	}, {	/* PL011 UART1 */
+		.dev_id		= "1c0a0000.uart",
+		.clk		= &osc2_clk,
+	}, {	/* PL011 UART2 */
+		.dev_id		= "1c0b0000.uart",
+		.clk		= &osc2_clk,
+	}, {	/* PL011 UART3 */
+		.dev_id		= "1c0c0000.uart",
+		.clk		= &osc2_clk,
+	}, {	/* SP805 WDT */
+		.dev_id		= "1c0f0000.wdt",
+		.clk		= &v2m_ref_clk,
+	}, {	/* PL111 CLCD */
+		.dev_id		= "1c1f0000.clcd",
+		.clk		= &osc1_clk,
+	},
 };
 
 void __init v2m_dt_init_early(void)
@@ -597,6 +653,10 @@ static struct of_dev_auxdata v2m_dt_auxdata_lookup[] __initdata = {
 	OF_DEV_AUXDATA("arm,vexpress-flash", V2M_NOR0, "physmap-flash",
 			&v2m_flash_data),
 	OF_DEV_AUXDATA("arm,primecell", V2M_MMCI, "mb:mmci", &v2m_mmci_data),
+	/* RS1 memory map */
+	OF_DEV_AUXDATA("arm,vexpress-flash", 0x08000000, "physmap-flash",
+			&v2m_flash_data),
+	OF_DEV_AUXDATA("arm,primecell", 0x1c050000, "mb:mmci", &v2m_mmci_data),
 	{}
 };