dt-bindings: pinctrl: mediatek,mt6779-pinctrl: Add MT6797

Combine MT6797 pin controller document into MT6779 one. reg and
reg-names property constraints are set using conditionals.
A conditional is also used to make interrupt-related properties
required on the MT6779 pin controller only, since the MT6797
controller doesn't support interrupts (or not yet, at least).
drive-strength and slew-rate properties which weren't described
in the MT6779 document before are brought in from the MT6797 one.
Both pin controllers share a common driver core so they should
both support these properties.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221028153505.23741-5-y.oudjana@protonmail.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml

@@ -8,6 +8,7 @@ title: Mediatek MT6779 Pin Controller
 
 maintainers:
   - Andy Teng <andy.teng@mediatek.com>
+  - Sean Wang <sean.wang@kernel.org>
 
 description:
   The MediaTek pin controller on MT6779 is used to control pin
@@ -15,23 +16,14 @@ description:
 
 properties:
   compatible:
-    const: mediatek,mt6779-pinctrl
+    enum:
+      - mediatek,mt6779-pinctrl
+      - mediatek,mt6797-pinctrl
 
   reg:
-    minItems: 9
-    maxItems: 9
+    description: Physical addresses for GPIO base(s) and EINT registers.
 
-  reg-names:
-    items:
-      - const: "gpio"
-      - const: "iocfg_rm"
-      - const: "iocfg_br"
-      - const: "iocfg_lm"
-      - const: "iocfg_lb"
-      - const: "iocfg_rt"
-      - const: "iocfg_lt"
-      - const: "iocfg_tl"
-      - const: "eint"
+  reg-names: true
 
   gpio-controller: true
 
@@ -58,17 +50,64 @@ properties:
   "#interrupt-cells":
     const: 2
 
-allOf:
-  - $ref: "pinctrl.yaml#"
-
 required:
   - compatible
   - reg
   - reg-names
   - gpio-controller
   - "#gpio-cells"
-  - interrupt-controller
+
+allOf:
+  - $ref: "pinctrl.yaml#"
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: mediatek,mt6779-pinctrl
+    then:
+      properties:
+        reg:
+          minItems: 9
+          maxItems: 9
+
+        reg-names:
+          items:
+            - const: gpio
+            - const: iocfg_rm
+            - const: iocfg_br
+            - const: iocfg_lm
+            - const: iocfg_lb
+            - const: iocfg_rt
+            - const: iocfg_lt
+            - const: iocfg_tl
+            - const: eint
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: mediatek,mt6797-pinctrl
+    then:
+      properties:
+        reg:
+          minItems: 5
+          maxItems: 5
+
+        reg-names:
+          items:
+            - const: gpio
+            - const: iocfgl
+            - const: iocfgb
+            - const: iocfgr
+            - const: iocfgt
+  - if:
+      properties:
+        reg-names:
+          contains:
+            const: eint
+    then:
+      required:
         - interrupts
+        - interrupt-controller
         - "#interrupt-cells"
 
 patternProperties:
@@ -111,6 +150,12 @@ patternProperties:
 
           input-schmitt-disable: true
 
+          drive-strength:
+            enum: [2, 4, 8, 12, 16]
+
+          slew-rate:
+            enum: [0, 1]
+
           mediatek,pull-up-adv:
             description: |
               Pull up setings for 2 pull resistors, R0 and R1. User can

Documentation/devicetree/bindings/pinctrl/mediatek,mt6797-pinctrl.yaml

-# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
-%YAML 1.2
----
-$id: http://devicetree.org/schemas/pinctrl/mediatek,mt6797-pinctrl.yaml#
-$schema: http://devicetree.org/meta-schemas/core.yaml#
-
-title: Mediatek MT6797 Pin Controller
-
-maintainers:
-  - Sean Wang <sean.wang@kernel.org>
-
-description: |+
-  The MediaTek's MT6797 Pin controller is used to control SoC pins.
-
-properties:
-  compatible:
-    const: mediatek,mt6797-pinctrl
-
-  reg:
-    minItems: 5
-    maxItems: 5
-
-  reg-names:
-    items:
-      - const: gpio
-      - const: iocfgl
-      - const: iocfgb
-      - const: iocfgr
-      - const: iocfgt
-
-  gpio-controller: true
-
-  "#gpio-cells":
-    const: 2
-    description: |
-      Number of cells in GPIO specifier. Since the generic GPIO
-      binding is used, the amount of cells must be specified as 2. See the below
-      mentioned gpio binding representation for description of particular cells.
-
-  interrupt-controller: true
-
-  interrupts:
-    maxItems: 1
-
-  "#interrupt-cells":
-    const: 2
-
-allOf:
-  - $ref: "pinctrl.yaml#"
-
-required:
-  - compatible
-  - reg
-  - reg-names
-  - gpio-controller
-  - "#gpio-cells"
-
-patternProperties:
-  '-[0-9]+$':
-    type: object
-    additionalProperties: false
-    patternProperties:
-      'pins':
-        type: object
-        additionalProperties: false
-        description: |
-          A pinctrl node should contain at least one subnodes representing the
-          pinctrl groups available on the machine. Each subnode will list the
-          pins it needs, and how they should be configured, with regard to muxer
-          configuration, pullups, drive strength, input enable/disable and input
-          schmitt.
-        $ref: "/schemas/pinctrl/pincfg-node.yaml"
-
-        properties:
-          pinmux:
-            description:
-              integer array, represents gpio pin number and mux setting.
-              Supported pin number and mux varies for different SoCs, and are
-              defined as macros in <soc>-pinfunc.h directly.
-
-          bias-disable: true
-
-          bias-pull-up: true
-
-          bias-pull-down: true
-
-          input-enable: true
-
-          input-disable: true
-
-          output-enable: true
-
-          output-low: true
-
-          output-high: true
-
-          input-schmitt-enable: true
-
-          input-schmitt-disable: true
-
-          drive-strength:
-            enum: [2, 4, 8, 12, 16]
-
-          slew-rate:
-            enum: [0, 1]
-
-          mediatek,pull-up-adv:
-            description: |
-              Pull up setings for 2 pull resistors, R0 and R1. User can
-              configure those special pins. Valid arguments are described as below:
-              0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
-              1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
-              2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
-              3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
-            $ref: /schemas/types.yaml#/definitions/uint32
-            enum: [0, 1, 2, 3]
-
-          mediatek,pull-down-adv:
-            description: |
-              Pull down settings for 2 pull resistors, R0 and R1. User can
-              configure those special pins. Valid arguments are described as below:
-              0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
-              1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
-              2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
-              3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
-            $ref: /schemas/types.yaml#/definitions/uint32
-            enum: [0, 1, 2, 3]
-
-          mediatek,tdsel:
-            description: |
-              An integer describing the steps for output level shifter duty
-              cycle when asserted (high pulse width adjustment). Valid arguments
-              are from 0 to 15.
-            $ref: /schemas/types.yaml#/definitions/uint32
-
-          mediatek,rdsel:
-            description: |
-              An integer describing the steps for input level shifter duty cycle
-              when asserted (high pulse width adjustment). Valid arguments are
-              from 0 to 63.
-            $ref: /schemas/types.yaml#/definitions/uint32
-
-        required:
-          - pinmux
-
-additionalProperties: false
-
-examples:
-  - |
-    #include <dt-bindings/interrupt-controller/irq.h>
-    #include <dt-bindings/interrupt-controller/arm-gic.h>
-    #include <dt-bindings/pinctrl/mt6797-pinfunc.h>
-
-    soc {
-        #address-cells = <2>;
-        #size-cells = <2>;
-
-        pio: pinctrl@10005000 {
-            compatible = "mediatek,mt6797-pinctrl";
-            reg = <0 0x10005000 0 0x1000>,
-                  <0 0x10002000 0 0x400>,
-                  <0 0x10002400 0 0x400>,
-                  <0 0x10002800 0 0x400>,
-                  <0 0x10002C00 0 0x400>;
-            reg-names = "gpio", "iocfgl", "iocfgb", "iocfgr", "iocfgt";
-            gpio-controller;
-            #gpio-cells = <2>;
-
-            uart_pins_a: uart-0 {
-                pins1 {
-                    pinmux = <MT6797_GPIO232__FUNC_URXD1>,
-                            <MT6797_GPIO233__FUNC_UTXD1>;
-                };
-            };
-        };
-    };

MAINTAINERS

@@ -16284,7 +16284,7 @@ M:	Sean Wang <sean.wang@kernel.org>
 L:	linux-mediatek@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 F:	Documentation/devicetree/bindings/pinctrl/mediatek,mt65xx-pinctrl.yaml
-F:	Documentation/devicetree/bindings/pinctrl/mediatek,mt6797-pinctrl.yaml
+F:	Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml
 F:	Documentation/devicetree/bindings/pinctrl/mediatek,mt7622-pinctrl.yaml
 F:	Documentation/devicetree/bindings/pinctrl/mediatek,mt8183-pinctrl.yaml
 F:	drivers/pinctrl/mediatek/