e1000: fix whitespace issues and multi-line comments

Fixes whitespace issues, such as lines exceeding 80 chars, needless blank
lines and the use of spaces where tabs are needed.  In addition, fix
multi-line comments to align with the networking standard.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>

drivers/net/ethernet/intel/e1000/e1000.h

@@ -142,7 +142,8 @@ struct e1000_adapter;
 #define E1000_MNG_VLAN_NONE	(-1)
 
 /* wrapper around a pointer to a socket buffer,
- * so a DMA handle can be stored along with the buffer */
+ * so a DMA handle can be stored along with the buffer
+ */
 struct e1000_buffer {
 	struct sk_buff *skb;
 	dma_addr_t dma;

drivers/net/ethernet/intel/e1000/e1000_ethtool.c

@@ -161,8 +161,8 @@ static int e1000_get_settings(struct net_device *netdev,
 		ethtool_cmd_speed_set(ecmd, adapter->link_speed);
 
 		/* unfortunately FULL_DUPLEX != DUPLEX_FULL
-		 *          and HALF_DUPLEX != DUPLEX_HALF */
-
+		 * and HALF_DUPLEX != DUPLEX_HALF
+		 */
 		if (adapter->link_duplex == FULL_DUPLEX)
 			ecmd->duplex = DUPLEX_FULL;
 		else
@@ -179,8 +179,7 @@ static int e1000_get_settings(struct net_device *netdev,
 	if ((hw->media_type == e1000_media_type_copper) &&
 	    netif_carrier_ok(netdev))
 		ecmd->eth_tp_mdix = (!!adapter->phy_info.mdix_mode ?
-							ETH_TP_MDI_X :
-							ETH_TP_MDI);
+				     ETH_TP_MDI_X : ETH_TP_MDI);
 	else
 		ecmd->eth_tp_mdix = ETH_TP_MDI_INVALID;
 
@@ -197,8 +196,7 @@ static int e1000_set_settings(struct net_device *netdev,
 	struct e1000_adapter *adapter = netdev_priv(netdev);
 	struct e1000_hw *hw = &adapter->hw;
 
-	/*
-	 * MDI setting is only allowed when autoneg enabled because
+	/* MDI setting is only allowed when autoneg enabled because
 	 * some hardware doesn't allow MDI setting when speed or
 	 * duplex is forced.
 	 */
@@ -260,8 +258,7 @@ static u32 e1000_get_link(struct net_device *netdev)
 {
 	struct e1000_adapter *adapter = netdev_priv(netdev);
 
-	/*
-	 * If the link is not reported up to netdev, interrupts are disabled,
+	/* If the link is not reported up to netdev, interrupts are disabled,
 	 * and so the physical link state may have changed since we last
 	 * looked. Set get_link_status to make sure that the true link
 	 * state is interrogated, rather than pulling a cached and possibly
@@ -517,15 +514,17 @@ static int e1000_set_eeprom(struct net_device *netdev,
 	ptr = (void *)eeprom_buff;
 
 	if (eeprom->offset & 1) {
-		/* need read/modify/write of first changed EEPROM word */
-		/* only the second byte of the word is being modified */
+		/* need read/modify/write of first changed EEPROM word
+		 * only the second byte of the word is being modified
+		 */
 		ret_val = e1000_read_eeprom(hw, first_word, 1,
 					    &eeprom_buff[0]);
 		ptr++;
 	}
 	if (((eeprom->offset + eeprom->len) & 1) && (ret_val == 0)) {
-		/* need read/modify/write of last changed EEPROM word */
-		/* only the first byte of the word is being modified */
+		/* need read/modify/write of last changed EEPROM word
+		 * only the first byte of the word is being modified
+		 */
 		ret_val = e1000_read_eeprom(hw, last_word, 1,
 		                  &eeprom_buff[last_word - first_word]);
 	}
@@ -606,11 +605,13 @@ static int e1000_set_ringparam(struct net_device *netdev,
 	rx_old = adapter->rx_ring;
 
 	err = -ENOMEM;
-	txdr = kcalloc(adapter->num_tx_queues, sizeof(struct e1000_tx_ring), GFP_KERNEL);
+	txdr = kcalloc(adapter->num_tx_queues, sizeof(struct e1000_tx_ring),
+		       GFP_KERNEL);
 	if (!txdr)
 		goto err_alloc_tx;
 
-	rxdr = kcalloc(adapter->num_rx_queues, sizeof(struct e1000_rx_ring), GFP_KERNEL);
+	rxdr = kcalloc(adapter->num_rx_queues, sizeof(struct e1000_rx_ring),
+		       GFP_KERNEL);
 	if (!rxdr)
 		goto err_alloc_rx;
 
@@ -642,7 +643,8 @@ static int e1000_set_ringparam(struct net_device *netdev,
 			goto err_setup_tx;
 
 		/* save the new, restore the old in order to free it,
-		 * then restore the new back again */
+		 * then restore the new back again
+		 */
 
 		adapter->rx_ring = rx_old;
 		adapter->tx_ring = tx_old;
@@ -784,7 +786,6 @@ static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data)
 	REG_SET_AND_CHECK(TCTL, 0xFFFFFFFF, 0x00000000);
 
 	if (hw->mac_type >= e1000_82543) {
-
 		REG_SET_AND_CHECK(RCTL, before, 0xFFFFFFFF);
 		REG_PATTERN_TEST(RDBAL, 0xFFFFFFF0, 0xFFFFFFFF);
 		REG_PATTERN_TEST(TXCW, 0xC000FFFF, 0x0000FFFF);
@@ -795,14 +796,11 @@ static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data)
 			REG_PATTERN_TEST(RA + (((i << 1) + 1) << 2), 0x8003FFFF,
 			                 0xFFFFFFFF);
 		}
-
 	} else {
-
 		REG_SET_AND_CHECK(RCTL, 0xFFFFFFFF, 0x01FFFFFF);
 		REG_PATTERN_TEST(RDBAL, 0xFFFFF000, 0xFFFFFFFF);
 		REG_PATTERN_TEST(TXCW, 0x0000FFFF, 0x0000FFFF);
 		REG_PATTERN_TEST(TDBAL, 0xFFFFF000, 0xFFFFFFFF);
-
 	}
 
 	value = E1000_MC_TBL_SIZE;
@@ -858,8 +856,9 @@ static int e1000_intr_test(struct e1000_adapter *adapter, u64 *data)
 
 	*data = 0;
 
-	/* NOTE: we don't test MSI interrupts here, yet */
-	/* Hook up test interrupt handler just for this test */
+	/* NOTE: we don't test MSI interrupts here, yet
+	 * Hook up test interrupt handler just for this test
+	 */
 	if (!request_irq(irq, e1000_test_intr, IRQF_PROBE_SHARED, netdev->name,
 			 netdev))
 		shared_int = false;
@@ -1260,7 +1259,8 @@ static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter)
 		ctrl_reg |= E1000_CTRL_ILOS; /* Invert Loss of Signal */
 	else {
 		/* Set the ILOS bit on the fiber Nic is half
-		 * duplex link is detected. */
+		 * duplex link is detected.
+		 */
 		stat_reg = er32(STATUS);
 		if ((stat_reg & E1000_STATUS_FD) == 0)
 			ctrl_reg |= (E1000_CTRL_ILOS | E1000_CTRL_SLU);
@@ -1493,7 +1493,8 @@ static int e1000_link_test(struct e1000_adapter *adapter, u64 *data)
 		hw->serdes_has_link = false;
 
 		/* On some blade server designs, link establishment
-		 * could take as long as 2-3 minutes */
+		 * could take as long as 2-3 minutes
+		 */
 		do {
 			e1000_check_for_link(hw);
 			if (hw->serdes_has_link)
@@ -1545,7 +1546,8 @@ static void e1000_diag_test(struct net_device *netdev,
 		e_info(hw, "offline testing starting\n");
 
 		/* Link test performed before hardware reset so autoneg doesn't
-		 * interfere with test result */
+		 * interfere with test result
+		 */
 		if (e1000_link_test(adapter, &data[4]))
 			eth_test->flags |= ETH_TEST_FL_FAILED;
 
@@ -1639,7 +1641,8 @@ static int e1000_wol_exclusion(struct e1000_adapter *adapter,
 	default:
 		/* dual port cards only support WoL on port A from now on
 		 * unless it was enabled in the eeprom for port B
-		 * so exclude FUNC_1 ports from having WoL enabled */
+		 * so exclude FUNC_1 ports from having WoL enabled
+		 */
 		if (er32(STATUS) & E1000_STATUS_FUNC_1 &&
 		    !adapter->eeprom_wol) {
 			wol->supported = 0;
@@ -1663,7 +1666,8 @@ static void e1000_get_wol(struct net_device *netdev,
 	wol->wolopts = 0;
 
 	/* this function will set ->supported = 0 and return 1 if wol is not
-	 * supported by this hardware */
+	 * supported by this hardware
+	 */
 	if (e1000_wol_exclusion(adapter, wol) ||
 	    !device_can_wakeup(&adapter->pdev->dev))
 		return;
@@ -1859,7 +1863,7 @@ static void e1000_get_strings(struct net_device *netdev, u32 stringset,
 			       ETH_GSTRING_LEN);
 			p += ETH_GSTRING_LEN;
 		}
-/*		BUG_ON(p - data != E1000_STATS_LEN * ETH_GSTRING_LEN); */
+		/* BUG_ON(p - data != E1000_STATS_LEN * ETH_GSTRING_LEN); */
 		break;
 	}
 }

drivers/net/ethernet/intel/e1000/e1000_param.c

@@ -267,7 +267,6 @@ static void e1000_check_copper_options(struct e1000_adapter *adapter);
  * value exists, a default value is used.  The final value is stored
  * in a variable in the adapter structure.
  **/
-
 void e1000_check_options(struct e1000_adapter *adapter)
 {
 	struct e1000_option opt;
@@ -319,7 +318,8 @@ void e1000_check_options(struct e1000_adapter *adapter)
 			.def  = E1000_DEFAULT_RXD,
 			.arg  = { .r = {
 				.min = E1000_MIN_RXD,
-				.max = mac_type < e1000_82544 ? E1000_MAX_RXD : E1000_MAX_82544_RXD
+				.max = mac_type < e1000_82544 ? E1000_MAX_RXD :
+				       E1000_MAX_82544_RXD
 			}}
 		};
 
@@ -488,7 +488,8 @@ void e1000_check_options(struct e1000_adapter *adapter)
 				/* save the setting, because the dynamic bits
 				 * change itr.
 				 * clear the lower two bits because they are
-				 * used as control */
+				 * used as control
+				 */
 				adapter->itr_setting = adapter->itr & ~3;
 				break;
 			}
@@ -533,7 +534,6 @@ void e1000_check_options(struct e1000_adapter *adapter)
  *
  * Handles speed and duplex options on fiber adapters
  **/
-
 static void e1000_check_fiber_options(struct e1000_adapter *adapter)
 {
 	int bd = adapter->bd_number;
@@ -559,7 +559,6 @@ static void e1000_check_fiber_options(struct e1000_adapter *adapter)
  *
  * Handles speed and duplex options on copper adapters
  **/
-
 static void e1000_check_copper_options(struct e1000_adapter *adapter)
 {
 	struct e1000_option opt;