Merge tag 'sunxi-dt-for-4.5' of...

Merge tag 'sunxi-dt-for-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt

Allwinner DT changes for 4.5

Allwinner device-tree related patches for the 4.5 merge window.
  * Support for the H3
  * Addition of the RSB to the relevant devices (sun8i, sun9i)
  * Addition of the Video Engine clocks for the older SoCs (sun4i, sun7i)
  * Addition of the DRAM gates for the older SoCs (sun4i, sun7i)
  * Addition of the audio codec to a bunch of boards
  * New board: ICNova SWAC

* tag 'sunxi-dt-for-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (40 commits)
  ARM: dts: sun7i: Olimex A20-SOM-EVB: Enable mmc3 (baseboard SD socket)
  ARM: dts: sun7i: Olimex A20-SOM-EVB: Add LRADC keys
  ARM: dts: sun9i: cubieboard4: Enable Reduced Serial Bus controller
  ARM: dts: sun9i: cubieboard4: Enable consumer IR receiver
  ARM: dts: sun9i: cubieboard4: Enable LEDs
  ARM: dts: sun7i: Add VE (Video Engine) module clock node
  ARM: dts: sun4i: Add VE (Video Engine) module clock node
  ARM: dts: sun8i: Add Orange Pi Plus support
  ARM: dts: sunxi: Add Allwinner H3 DTSI
  ARM: dts: sun7i: Add DRAM gates
  ARM: dts: sun4i: Add DRAM gates
  ARM: dts: sun9i: Add NMI controller device node
  ARM: dts: sun9i: optimus: Enable Reduced Serial Bus controller
  ARM: dts: sun9i: Add Reduced Serial Bus controller device node to A80 dtsi
  ARM: dts: sun9i: optimus: Enable consumer IR receiver
  ARM: dts: sun9i: Add consumer IR receiver device node and pinmux settings
  ARM: dts: sun9i: optimus: Enable LED3
  ARM: dts: sun9i: Add A80 R_PIO pin controller device node
  ARM: dts: sun9i: Add TODO comments for the main and low power clocks
  ARM: dts: sun9i: Add A80 PRCM clocks and reset control nodes
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

arch/arm/boot/dts/Makefile

@@ -651,6 +651,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
 	sun7i-a20-cubietruck.dtb \
 	sun7i-a20-hummingbird.dtb \
 	sun7i-a20-i12-tvbox.dtb \
+	sun7i-a20-icnova-swac.dtb \
 	sun7i-a20-m3.dtb \
 	sun7i-a20-mk808c.dtb \
 	sun7i-a20-olimex-som-evb.dtb \
@@ -673,7 +674,8 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-a33-ga10h-v1.1.dtb \
 	sun8i-a33-ippo-q8h-v1.2.dtb \
 	sun8i-a33-q8-tablet.dtb \
-	sun8i-a33-sinlinx-sina33.dtb
+	sun8i-a33-sinlinx-sina33.dtb \
+	sun8i-h3-orangepi-plus.dtb
 dtb-$(CONFIG_MACH_SUN9I) += \
 	sun9i-a80-optimus.dtb \
 	sun9i-a80-cubieboard4.dtb

arch/arm/boot/dts/sun4i-a10-gemei-g9.dts

@@ -65,12 +65,19 @@ chosen {
 /*
  * TODO:
  *   2x cameras via CSI
- *   audio
+ *   audio input
  *   AXP battery management
  *   NAND
  *   OTG
  *   Touchscreen - gt801_2plus1 @ i2c adapter 2 @ 0x48
  */
+&codec {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
 
 &ehci0 {
 	status = "okay";
@@ -86,15 +93,13 @@ &i2c0 {
 	status = "okay";
 
 	axp209: pmic@34 {
-		compatible = "x-powers,axp209";
 		reg = <0x34>;
 		interrupts = <0>;
-
-		interrupt-controller;
-		#interrupt-cells = <1>;
 	};
 };
 
+#include "axp209.dtsi"
+
 &i2c1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c1_pins_a>;
@@ -110,7 +115,7 @@ bma250@18 {
 };
 
 &lradc {
-	vref-supply = <&reg_vcc3v0>;
+	vref-supply = <&reg_ldo2>;
 
 	status = "okay";
 
@@ -146,6 +151,31 @@ &mmc0 {
 	status = "okay";
 };
 
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1250000>;
+	regulator-max-microvolt = <1250000>;
+	regulator-name = "vdd-int-dll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
 &reg_usb1_vbus {
 	status = "okay";
 };

arch/arm/boot/dts/sun4i-a10-inet1.dts

@@ -47,6 +47,7 @@
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "iNet-1";
@@ -56,11 +57,25 @@ aliases {
 		serial0 = &uart0;
 	};
 
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&bl_en_pin_inet>;
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
 };
 
+&codec {
+	status = "okay";
+};
+
 &cpu0 {
 	cpu-supply = <&reg_dcdc2>;
 };
@@ -104,6 +119,19 @@ &i2c2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c2_pins_a>;
 	status = "okay";
+
+	ft5x: touchscreen@38 {
+		compatible = "edt,edt-ft5406";
+		reg = <0x38>;
+		interrupt-parent = <&pio>;
+		interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&touchscreen_wake_pin>;
+		wake-gpios = <&pio 1 13 GPIO_ACTIVE_HIGH>; /* PB13 */
+		touchscreen-size-x = <600>;
+		touchscreen-size-y = <1024>;
+		touchscreen-swapped-x-y;
+	};
 };
 
 &lradc {
@@ -151,6 +179,20 @@ &otg_sram {
 };
 
 &pio {
+	bl_en_pin_inet: bl_en_pin@0 {
+		allwinner,pins = "PH7";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
+	touchscreen_wake_pin: touchscreen_wake_pin@0 {
+		allwinner,pins = "PB13";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
 	usb0_id_detect_pin: usb0_id_detect_pin@0 {
 		allwinner,pins = "PH4";
 		allwinner,function = "gpio_in";
@@ -166,6 +208,12 @@ usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
 	};
 };
 
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pins_a>;
+	status = "okay";
+};
+
 &reg_dcdc2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1000000>;

arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts

@@ -59,6 +59,159 @@ aliases {
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	gpio_keys {
+		compatible = "gpio-keys-polled";
+		pinctrl-names = "default";
+		pinctrl-0 = <&key_pins_inet9f>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <20>;
+
+		button@0 {
+			label = "Left Joystick Left";
+			linux,code = <ABS_X>;
+			linux,input-type = <EV_ABS>;
+			linux,input-value = <0xffffffff>; /* -1 */
+			gpios = <&pio 0 6 GPIO_ACTIVE_LOW>; /* PA6 */
+		};
+
+		button@1 {
+			label = "Left Joystick Right";
+			linux,code = <ABS_X>;
+			linux,input-type = <EV_ABS>;
+			linux,input-value = <1>;
+			gpios = <&pio 0 5 GPIO_ACTIVE_LOW>; /* PA5 */
+		};
+
+		button@2 {
+			label = "Left Joystick Up";
+			linux,code = <ABS_Y>;
+			linux,input-type = <EV_ABS>;
+			linux,input-value = <0xffffffff>; /* -1 */
+			gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */
+		};
+
+		button@3 {
+			label = "Left Joystick Down";
+			linux,code = <ABS_Y>;
+			linux,input-type = <EV_ABS>;
+			linux,input-value = <1>;
+			gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
+		};
+
+		button@4 {
+			label = "Right Joystick Left";
+			linux,code = <ABS_Z>;
+			linux,input-type = <EV_ABS>;
+			linux,input-value = <0xffffffff>; /* -1 */
+			gpios = <&pio 0 1 GPIO_ACTIVE_LOW>; /* PA1 */
+		};
+
+		button@5 {
+			label = "Right Joystick Right";
+			linux,code = <ABS_Z>;
+			linux,input-type = <EV_ABS>;
+			linux,input-value = <1>;
+			gpios = <&pio 0 0 GPIO_ACTIVE_LOW>; /* PA0 */
+		};
+
+		button@6 {
+			label = "Right Joystick Up";
+			linux,code = <ABS_RZ>;
+			linux,input-type = <EV_ABS>;
+			linux,input-value = <0xffffffff>; /* -1 */
+			gpios = <&pio 0 3 GPIO_ACTIVE_LOW>; /* PA3 */
+		};
+
+		button@7 {
+			label = "Right Joystick Down";
+			linux,code = <ABS_RZ>;
+			linux,input-type = <EV_ABS>;
+			linux,input-value = <1>;
+			gpios = <&pio 0 4 GPIO_ACTIVE_LOW>; /* PA4 */
+		};
+
+		button@8 {
+			label = "DPad Left";
+			linux,code = <ABS_HAT0X>;
+			linux,input-type = <EV_ABS>;
+			linux,input-value = <0xffffffff>; /* -1 */
+			gpios = <&pio 7 23 GPIO_ACTIVE_LOW>; /* PH23 */
+		};
+
+		button@9 {
+			label = "DPad Right";
+			linux,code = <ABS_HAT0X>;
+			linux,input-type = <EV_ABS>;
+			linux,input-value = <1>;
+			gpios = <&pio 7 24 GPIO_ACTIVE_LOW>; /* PH24 */
+		};
+
+		button@10 {
+			label = "DPad Up";
+			linux,code = <ABS_HAT0Y>;
+			linux,input-type = <EV_ABS>;
+			linux,input-value = <0xffffffff>; /* -1 */
+			gpios = <&pio 7 25 GPIO_ACTIVE_LOW>; /* PH25 */
+		};
+
+		button@11 {
+			label = "DPad Down";
+			linux,code = <ABS_HAT0Y>;
+			linux,input-type = <EV_ABS>;
+			linux,input-value = <1>;
+			gpios = <&pio 7 26 GPIO_ACTIVE_LOW>; /* PH26 */
+		};
+
+		button@12 {
+			label = "Button X";
+			linux,code = <BTN_X>;
+			gpios = <&pio 0 16 GPIO_ACTIVE_LOW>; /* PA16 */
+		};
+
+		button@13 {
+			label = "Button Y";
+			linux,code = <BTN_Y>;
+			gpios = <&pio 0 14 GPIO_ACTIVE_LOW>; /* PA14 */
+		};
+
+		button@14 {
+			label = "Button A";
+			linux,code = <BTN_A>;
+			gpios = <&pio 0 17 GPIO_ACTIVE_LOW>; /* PA17 */
+		};
+
+		button@15 {
+			label = "Button B";
+			linux,code = <BTN_B>;
+			gpios = <&pio 0 15 GPIO_ACTIVE_LOW>; /* PA15 */
+		};
+
+		button@16 {
+			label = "Select Button";
+			linux,code = <BTN_SELECT>;
+			gpios = <&pio 0 11 GPIO_ACTIVE_LOW>; /* PA11 */
+		};
+
+		button@17 {
+			label = "Start Button";
+			linux,code = <BTN_START>;
+			gpios = <&pio 0 12 GPIO_ACTIVE_LOW>; /* PA12 */
+		};
+
+		button@18 {
+			label = "Top Left Button";
+			linux,code = <BTN_TL>;
+			gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 */
+		};
+
+		button@19 {
+			label = "Top Right Button";
+			linux,code = <BTN_TR>;
+			gpios = <&pio 0 13 GPIO_ACTIVE_LOW>; /* PA13 */
+		};
+	};
 };
 
 &cpu0 {
@@ -157,6 +310,17 @@ &otg_sram {
 };
 
 &pio {
+	key_pins_inet9f: key_pins@0 {
+		allwinner,pins = "PA0", "PA1", "PA3", "PA4",
+				 "PA5", "PA6", "PA8", "PA9",
+				 "PA11", "PA12", "PA13",
+				 "PA14", "PA15", "PA16", "PA17",
+				 "PH22", "PH23", "PH24", "PH25", "PH26";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	};
+
 	usb0_id_detect_pin: usb0_id_detect_pin@0 {
 		allwinner,pins = "PH4";
 		allwinner,function = "gpio_in";

arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts

@@ -47,6 +47,7 @@
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "Point of View Protab2-IPS9";
@@ -56,6 +57,16 @@ aliases {
 		serial0 = &uart0;
 	};
 
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&bl_en_pin_protab>;
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+		enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
@@ -93,6 +104,22 @@ &i2c2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c2_pins_a>;
 	status = "okay";
+
+	pixcir_ts@5c {
+		pinctrl-names = "default";
+		pinctrl-0 = <&touchscreen_pins>;
+		compatible = "pixcir,pixcir_tangoc";
+		reg = <0x5c>;
+		interrupt-parent = <&pio>;
+		interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>; /* EINT21 (PH21) */
+		attb-gpio = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* PH21 */
+		enable-gpios = <&pio 0 5 GPIO_ACTIVE_LOW>;
+		wake-gpios = <&pio 1 13 GPIO_ACTIVE_LOW>;
+		touchscreen-size-x = <1024>;
+		touchscreen-size-y = <768>;
+		touchscreen-inverted-x;
+		touchscreen-inverted-y;
+	};
 };
 
 &lradc {
@@ -129,6 +156,20 @@ &otg_sram {
 };
 
 &pio {
+	bl_en_pin_protab: bl_en_pin@0 {
+		allwinner,pins = "PH7";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
+	touchscreen_pins: touchscreen_pins@0 {
+		allwinner,pins = "PA5", "PB13";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
 	usb0_id_detect_pin: usb0_id_detect_pin@0 {
 		allwinner,pins = "PH4";
 		allwinner,function = "gpio_in";
@@ -144,6 +185,12 @@ usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
 	};
 };
 
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pins_a>;
+	status = "okay";
+};
+
 &reg_dcdc2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1000000>;

arch/arm/boot/dts/sun4i-a10.dtsi

@@ -66,7 +66,7 @@ framebuffer@0 {
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_be0-lcd0-hdmi";
 			clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>,
-				 <&ahb_gates 44>;
+				 <&ahb_gates 44>, <&dram_gates 26>;
 			status = "disabled";
 		};
 
@@ -75,7 +75,8 @@ framebuffer@1 {
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_fe0-de_be0-lcd0-hdmi";
 			clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>,
-				 <&ahb_gates 44>, <&ahb_gates 46>;
+				 <&ahb_gates 44>, <&ahb_gates 46>,
+				 <&dram_gates 25>, <&dram_gates 26>;
 			status = "disabled";
 		};
 
@@ -84,7 +85,8 @@ framebuffer@2 {
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_fe0-de_be0-lcd0";
 			clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 44>,
-				 <&ahb_gates 46>;
+				 <&ahb_gates 46>, <&dram_gates 25>,
+				 <&dram_gates 26>;
 			status = "disabled";
 		};
 
@@ -93,7 +95,8 @@ framebuffer@3 {
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_fe0-de_be0-lcd0-tve0";
 			clocks = <&pll5 1>, <&ahb_gates 34>, <&ahb_gates 36>,
-				 <&ahb_gates 44>, <&ahb_gates 46>;
+				 <&ahb_gates 44>, <&ahb_gates 46>,
+				 <&dram_gates 25>, <&dram_gates 26>;
 			status = "disabled";
 		};
 	};
@@ -492,6 +495,40 @@ spi3_clk: clk@01c200d4 {
 			clock-output-names = "spi3";
 		};
 
+		dram_gates: clk@01c20100 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun4i-a10-dram-gates-clk";
+			reg = <0x01c20100 0x4>;
+			clocks = <&pll5 0>;
+			clock-indices = <0>,
+					<1>, <2>,
+					<3>,
+					<4>,
+					<5>, <6>,
+					<15>,
+					<24>, <25>,
+					<26>, <27>,
+					<28>, <29>;
+			clock-output-names = "dram_ve",
+					     "dram_csi0", "dram_csi1",
+					     "dram_ts",
+					     "dram_tvd",
+					     "dram_tve0", "dram_tve1",
+					     "dram_output",
+					     "dram_de_fe1", "dram_de_fe0",
+					     "dram_de_be0", "dram_de_be1",
+					     "dram_de_mp", "dram_ace";
+		};
+
+		ve_clk: clk@01c2013c {
+			#clock-cells = <0>;
+			#reset-cells = <0>;
+			compatible = "allwinner,sun4i-a10-ve-clk";
+			reg = <0x01c2013c 0x4>;
+			clocks = <&pll4>;
+			clock-output-names = "ve";
+		};
+
 		codec_clk: clk@01c20140 {
 			#clock-cells = <0>;
 			compatible = "allwinner,sun4i-a10-codec-clk";

arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts

@@ -86,6 +86,20 @@ &ehci0 {
 	status = "okay";
 };
 
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	axp152: pmic@30 {
+		compatible = "x-powers,axp152";
+		reg = <0x30>;
+		interrupts = <0>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+};
+
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_t004>;

arch/arm/boot/dts/sun5i-a13-utoo-p66.dts

@@ -47,11 +47,21 @@
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "Utoo P66";
 	compatible = "utoo,p66", "allwinner,sun5i-a13";
 
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		/* Note levels of 10 / 20% result in backlight off */
+		brightness-levels = <0 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <6>;
+		/* TODO: backlight uses axp gpio1 as enable pin */
+	};
+
 	i2c_lcd: i2c@0 {
 		/* The lcd panel i2c interface is hooked up via gpios */
 		compatible = "i2c-gpio";
@@ -201,6 +211,12 @@ usb0_vbus_pin_a: usb0_vbus_pin@0 {
 	};
 };
 
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pins>;
+	status = "okay";
+};
+
 &reg_dcdc2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1000000>;

arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts

@@ -113,18 +113,83 @@ &mmc0_pins_a {
 	allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
 };
 
-&reg_usb1_vbus {
-	gpio = <&pio 7 27 GPIO_ACTIVE_HIGH>;
+&p2wi {
 	status = "okay";
+
+	axp22x: pmic@68 {
+		compatible = "x-powers,axp221";
+		reg = <0x68>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
 };
 
-&usb1_vbus_pin_a {
-	allwinner,pins = "PH27";
+#include "axp22x.dtsi"
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <2700000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "avcc";
 };
 
-&usbphy {
-	usb1_vbus-supply = <&reg_usb1_vbus>;
-	status = "okay";
+&reg_dc1sw {
+	regulator-name = "vcc-lcd-usb2";
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+};
+
+&reg_dc5ldo {
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1320000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-3v0";
+};
+
+&reg_dcdc2 {
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1320000>;
+	regulator-name = "vdd-gpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1320000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc4 {
+	regulator-always-on;
+	regulator-min-microvolt = <700000>;
+	regulator-max-microvolt = <1320000>;
+	regulator-name = "vdd-sys-dll";
+};
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dldo1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+/* Voltage source for I2C pullup resistors for I2C Bus 0 */
+&reg_dldo3 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "vddio-csi";
 };
 
 &uart0 {
@@ -132,3 +197,9 @@ &uart0 {
 	pinctrl-0 = <&uart0_pins_a>;
 	status = "okay";
 };
+
+&usbphy {
+	usb1_vbus-supply = <&reg_dldo1>;
+	usb2_vbus-supply = <&reg_dc1sw>;
+	status = "okay";
+};

arch/arm/boot/dts/sun7i-a20-bananapi.dts

@@ -92,6 +92,10 @@ &ahci {
 	status = "okay";
 };
 
+&codec {
+	status = "okay";
+};
+
 &cpu0 {
 	cpu-supply = <&reg_dcdc2>;
 	operating-points = <

arch/arm/boot/dts/sun7i-a20-icnova-swac.dts

+/*
+ * Copyright 2015 Stefan Roese <sr@denx.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	model = "ICnova-A20 SWAC";
+	compatible = "swac,icnova-a20-swac", "incircuit,icnova-a20", "allwinner,sun7i-a20";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&gmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac_pins_mii_a>;
+	phy = <&phy1>;
+	phy-mode = "mii";
+	status = "okay";
+
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_a>;
+	status = "okay";
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 8 5 GPIO_ACTIVE_HIGH>; /* PI5 */
+	cd-inverted;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+#include "axp209.dtsi"
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-int-dll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_usb1_vbus {
+	status = "okay";
+};
+
+&reg_usb2_vbus {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	usb2_vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
+};

arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts

 /*
  * Copyright 2015 - Marcus Cooper <codekipper@gmail.com>
+ * Copyright 2015 - Karsten Merker <merker@debian.org>
  *
  * This file is dual-licensed: you can use it either under the terms
  * of the GPL or the X11 license, at your option. Note that this dual
@@ -45,6 +46,7 @@
 #include "sunxi-common-regulators.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/pinctrl/sun4i-a10.h>
 
@@ -86,6 +88,10 @@ &ehci1 {
 	status = "okay";
 };
 
+&codec {
+	status = "okay";
+};
+
 &gmac {
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac_pins_rgmii_a>;
@@ -110,6 +116,60 @@ axp209: pmic@34 {
 	};
 };
 
+&lradc {
+	vref-supply = <&reg_vcc3v0>;
+	status = "okay";
+
+	button@190 {
+		label = "Volume Up";
+		linux,code = <KEY_VOLUMEUP>;
+		channel = <0>;
+		voltage = <190000>;
+	};
+
+	button@390 {
+		label = "Volume Down";
+		linux,code = <KEY_VOLUMEDOWN>;
+		channel = <0>;
+		voltage = <390000>;
+	};
+
+	button@600 {
+		label = "Menu";
+		linux,code = <KEY_MENU>;
+		channel = <0>;
+		voltage = <600000>;
+	};
+
+	button@800 {
+		label = "Search";
+		linux,code = <KEY_SEARCH>;
+		channel = <0>;
+		voltage = <800000>;
+	};
+
+	button@980 {
+		label = "Home";
+		linux,code = <KEY_HOMEPAGE>;
+		channel = <0>;
+		voltage = <980000>;
+	};
+
+	button@1180 {
+		label = "Esc";
+		linux,code = <KEY_ESC>;
+		channel = <0>;
+		voltage = <1180000>;
+	};
+
+	button@1400 {
+		label = "Enter";
+		linux,code = <KEY_ENTER>;
+		channel = <0>;
+		voltage = <1400000>;
+	};
+};
+
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
@@ -120,6 +180,16 @@ &mmc0 {
 	status = "okay";
 };
 
+&mmc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc3_pins_a>, <&mmc3_cd_pin_olimex_som_evb>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 0 GPIO_ACTIVE_HIGH>; /* PH0 */
+	cd-inverted;
+	status = "okay";
+};
+
 &ohci0 {
 	status = "okay";
 };
@@ -142,6 +212,13 @@ led_pins_olimex_som_evb: led_pins@0 {
 		allwinner,drive = <SUN4I_PINCTRL_20_MA>;
 		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 	};
+
+	mmc3_cd_pin_olimex_som_evb: mmc3_cd_pin@0 {
+		allwinner,pins = "PH0";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	};
 };
 
 &reg_ahci_5v {

arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts

@@ -95,6 +95,10 @@ &ahci {
 	status = "okay";
 };
 
+&codec {
+	status = "okay";
+};
+
 &ehci0 {
 	status = "okay";
 };

arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts

@@ -82,6 +82,10 @@ &ahci {
 	status = "okay";
 };
 
+&codec {
+	status = "okay";
+};
+
 &cpu0 {
 	cpu-supply = <&reg_dcdc2>;
 };

arch/arm/boot/dts/sun7i-a20-pcduino3.dts

@@ -111,6 +111,10 @@ &ahci_pwr_pin_a {
 	allwinner,pins = "PH2";
 };
 
+&codec {
+	status = "okay";
+};
+
 &cpu0 {
 	cpu-supply = <&reg_dcdc2>;
 };

arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts

@@ -62,6 +62,10 @@ chosen {
 	};
 };
 
+&codec {
+	status = "okay";
+};
+
 &cpu0 {
 	cpu-supply = <&reg_dcdc2>;
 };

arch/arm/boot/dts/sun7i-a20.dtsi

@@ -68,7 +68,7 @@ framebuffer@0 {
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_be0-lcd0-hdmi";
 			clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>,
-				 <&ahb_gates 44>;
+				 <&ahb_gates 44>, <&dram_gates 26>;
 			status = "disabled";
 		};
 
@@ -76,7 +76,8 @@ framebuffer@1 {
 			compatible = "allwinner,simple-framebuffer",
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_be0-lcd0";
-			clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 44>;
+			clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 44>,
+				 <&dram_gates 26>;
 			status = "disabled";
 		};
 
@@ -85,7 +86,7 @@ framebuffer@2 {
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_be0-lcd0-tve0";
 			clocks = <&pll5 1>, <&ahb_gates 34>, <&ahb_gates 36>,
-				 <&ahb_gates 44>;
+				 <&ahb_gates 44>, <&dram_gates 26>;
 			status = "disabled";
 		};
 	};
@@ -501,6 +502,40 @@ spi3_clk: clk@01c200d4 {
 			clock-output-names = "spi3";
 		};
 
+		dram_gates: clk@01c20100 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun4i-a10-dram-gates-clk";
+			reg = <0x01c20100 0x4>;
+			clocks = <&pll5 0>;
+			clock-indices = <0>,
+					<1>, <2>,
+					<3>,
+					<4>,
+					<5>, <6>,
+					<15>,
+					<24>, <25>,
+					<26>, <27>,
+					<28>, <29>;
+			clock-output-names = "dram_ve",
+					     "dram_csi0", "dram_csi1",
+					     "dram_ts",
+					     "dram_tvd",
+					     "dram_tve0", "dram_tve1",
+					     "dram_output",
+					     "dram_de_fe1", "dram_de_fe0",
+					     "dram_de_be0", "dram_de_be1",
+					     "dram_de_mp", "dram_ace";
+		};
+
+		ve_clk: clk@01c2013c {
+			#clock-cells = <0>;
+			#reset-cells = <0>;
+			compatible = "allwinner,sun4i-a10-ve-clk";
+			reg = <0x01c2013c 0x4>;
+			clocks = <&pll4>;
+			clock-output-names = "ve";
+		};
+
 		codec_clk: clk@01c20140 {
 			#clock-cells = <0>;
 			compatible = "allwinner,sun4i-a10-codec-clk";

arch/arm/boot/dts/sun8i-a23-a33.dtsi

@@ -56,7 +56,7 @@ chosen {
 		#size-cells = <1>;
 		ranges;
 
-		framebuffer@0 {
+		simplefb_lcd: framebuffer@0 {
 			compatible = "allwinner,simple-framebuffer",
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_be0-lcd0";

arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts

+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	model = "Xunlong Orange Pi Plus";
+	compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	cd-inverted;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};

arch/arm/boot/dts/sun8i-h3.dtsi

+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "skeleton.dtsi"
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <1>;
+		};
+
+		cpu@2 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <2>;
+		};
+
+		cpu@3 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <3>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		osc24M: osc24M_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+			clock-output-names = "osc24M";
+		};
+
+		osc32k: osc32k_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+			clock-output-names = "osc32k";
+		};
+
+		pll1: clk@01c20000 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun8i-a23-pll1-clk";
+			reg = <0x01c20000 0x4>;
+			clocks = <&osc24M>;
+			clock-output-names = "pll1";
+		};
+
+		/* dummy clock until actually implemented */
+		pll5: pll5_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <0>;
+			clock-output-names = "pll5";
+		};
+
+		pll6: clk@01c20028 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun6i-a31-pll6-clk";
+			reg = <0x01c20028 0x4>;
+			clocks = <&osc24M>;
+			clock-output-names = "pll6", "pll6x2";
+		};
+
+		pll6d2: pll6d2_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clock-div = <2>;
+			clock-mult = <1>;
+			clocks = <&pll6 0>;
+			clock-output-names = "pll6d2";
+		};
+
+		/* dummy clock until pll6 can be reused */
+		pll8: pll8_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <1>;
+			clock-output-names = "pll8";
+		};
+
+		cpu: cpu_clk@01c20050 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-cpu-clk";
+			reg = <0x01c20050 0x4>;
+			clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
+			clock-output-names = "cpu";
+		};
+
+		axi: axi_clk@01c20050 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-axi-clk";
+			reg = <0x01c20050 0x4>;
+			clocks = <&cpu>;
+			clock-output-names = "axi";
+		};
+
+		ahb1: ahb1_clk@01c20054 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun6i-a31-ahb1-clk";
+			reg = <0x01c20054 0x4>;
+			clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
+			clock-output-names = "ahb1";
+		};
+
+		ahb2: ahb2_clk@01c2005c {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun8i-h3-ahb2-clk";
+			reg = <0x01c2005c 0x4>;
+			clocks = <&ahb1>, <&pll6d2>;
+			clock-output-names = "ahb2";
+		};
+
+		apb1: apb1_clk@01c20054 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-apb0-clk";
+			reg = <0x01c20054 0x4>;
+			clocks = <&ahb1>;
+			clock-output-names = "apb1";
+		};
+
+		apb2: apb2_clk@01c20058 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-apb1-clk";
+			reg = <0x01c20058 0x4>;
+			clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
+			clock-output-names = "apb2";
+		};
+
+		bus_gates: clk@01c20060 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun8i-h3-bus-gates-clk";
+			reg = <0x01c20060 0x14>;
+			clocks = <&ahb1>, <&ahb2>, <&apb1>, <&apb2>;
+			clock-names = "ahb1", "ahb2", "apb1", "apb2";
+			clock-indices = <5>, <6>, <8>,
+					<9>, <10>, <13>,
+					<14>, <17>, <18>,
+					<19>, <20>,
+					<21>, <23>,
+					<24>, <25>,
+					<26>, <27>,
+					<28>, <29>,
+					<30>, <31>, <32>,
+					<35>, <36>, <37>,
+					<40>, <41>, <43>,
+					<44>, <52>, <53>,
+					<54>, <64>,
+					<65>, <69>, <72>,
+					<76>, <77>, <78>,
+					<96>, <97>, <98>,
+					<112>, <113>,
+					<114>, <115>,
+					<116>, <128>, <135>;
+			clock-output-names = "bus_ce", "bus_dma", "bus_mmc0",
+					     "bus_mmc1", "bus_mmc2", "bus_nand",
+					     "bus_sdram", "bus_gmac", "bus_ts",
+					     "bus_hstimer", "bus_spi0",
+					     "bus_spi1", "bus_otg",
+					     "bus_otg_ehci0", "bus_ehci1",
+					     "bus_ehci2", "bus_ehci3",
+					     "bus_otg_ohci0", "bus_ohci1",
+					     "bus_ohci2", "bus_ohci3", "bus_ve",
+					     "bus_lcd0", "bus_lcd1", "bus_deint",
+					     "bus_csi", "bus_tve", "bus_hdmi",
+					     "bus_de", "bus_gpu", "bus_msgbox",
+					     "bus_spinlock", "bus_codec",
+					     "bus_spdif", "bus_pio", "bus_ths",
+					     "bus_i2s0", "bus_i2s1", "bus_i2s2",
+					     "bus_i2c0", "bus_i2c1", "bus_i2c2",
+					     "bus_uart0", "bus_uart1",
+					     "bus_uart2", "bus_uart3",
+					     "bus_scr", "bus_ephy", "bus_dbg";
+		};
+
+		mmc0_clk: clk@01c20088 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun4i-a10-mmc-clk";
+			reg = <0x01c20088 0x4>;
+			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+			clock-output-names = "mmc0",
+					     "mmc0_output",
+					     "mmc0_sample";
+		};
+
+		mmc1_clk: clk@01c2008c {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun4i-a10-mmc-clk";
+			reg = <0x01c2008c 0x4>;
+			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+			clock-output-names = "mmc1",
+					     "mmc1_output",
+					     "mmc1_sample";
+		};
+
+		mmc2_clk: clk@01c20090 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun4i-a10-mmc-clk";
+			reg = <0x01c20090 0x4>;
+			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+			clock-output-names = "mmc2",
+					     "mmc2_output",
+					     "mmc2_sample";
+		};
+
+		mbus_clk: clk@01c2015c {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun8i-a23-mbus-clk";
+			reg = <0x01c2015c 0x4>;
+			clocks = <&osc24M>, <&pll6 1>, <&pll5>;
+			clock-output-names = "mbus";
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		dma: dma-controller@01c02000 {
+			compatible = "allwinner,sun8i-h3-dma";
+			reg = <0x01c02000 0x1000>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&bus_gates 6>;
+			resets = <&ahb_rst 6>;
+			#dma-cells = <1>;
+		};
+
+		mmc0: mmc@01c0f000 {
+			compatible = "allwinner,sun5i-a13-mmc";
+			reg = <0x01c0f000 0x1000>;
+			clocks = <&bus_gates 8>,
+				 <&mmc0_clk 0>,
+				 <&mmc0_clk 1>,
+				 <&mmc0_clk 2>;
+			clock-names = "ahb",
+				      "mmc",
+				      "output",
+				      "sample";
+			resets = <&ahb_rst 8>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc1: mmc@01c10000 {
+			compatible = "allwinner,sun5i-a13-mmc";
+			reg = <0x01c10000 0x1000>;
+			clocks = <&bus_gates 9>,
+				 <&mmc1_clk 0>,
+				 <&mmc1_clk 1>,
+				 <&mmc1_clk 2>;
+			clock-names = "ahb",
+				      "mmc",
+				      "output",
+				      "sample";
+			resets = <&ahb_rst 9>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc2: mmc@01c11000 {
+			compatible = "allwinner,sun5i-a13-mmc";
+			reg = <0x01c11000 0x1000>;
+			clocks = <&bus_gates 10>,
+				 <&mmc2_clk 0>,
+				 <&mmc2_clk 1>,
+				 <&mmc2_clk 2>;
+			clock-names = "ahb",
+				      "mmc",
+				      "output",
+				      "sample";
+			resets = <&ahb_rst 10>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		pio: pinctrl@01c20800 {
+			compatible = "allwinner,sun8i-h3-pinctrl";
+			reg = <0x01c20800 0x400>;
+			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&bus_gates 69>;
+			gpio-controller;
+			#gpio-cells = <3>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			uart0_pins_a: uart0@0 {
+				allwinner,pins = "PA4", "PA5";
+				allwinner,function = "uart0";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			mmc0_pins_a: mmc0@0 {
+				allwinner,pins = "PF0", "PF1", "PF2", "PF3",
+						 "PF4", "PF5";
+				allwinner,function = "mmc0";
+				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			mmc0_cd_pin: mmc0_cd_pin@0 {
+				allwinner,pins = "PF6";
+				allwinner,function = "gpio_in";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+			};
+
+			mmc1_pins_a: mmc1@0 {
+				allwinner,pins = "PG0", "PG1", "PG2", "PG3",
+						 "PG4", "PG5";
+				allwinner,function = "mmc1";
+				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+		};
+
+		ahb_rst: reset@01c202c0 {
+			#reset-cells = <1>;
+			compatible = "allwinner,sun6i-a31-ahb1-reset";
+			reg = <0x01c202c0 0xc>;
+		};
+
+		apb1_rst: reset@01c202d0 {
+			#reset-cells = <1>;
+			compatible = "allwinner,sun6i-a31-clock-reset";
+			reg = <0x01c202d0 0x4>;
+		};
+
+		apb2_rst: reset@01c202d8 {
+			#reset-cells = <1>;
+			compatible = "allwinner,sun6i-a31-clock-reset";
+			reg = <0x01c202d8 0x4>;
+		};
+
+		timer@01c20c00 {
+			compatible = "allwinner,sun4i-a10-timer";
+			reg = <0x01c20c00 0xa0>;
+			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc24M>;
+		};
+
+		wdt0: watchdog@01c20ca0 {
+			compatible = "allwinner,sun6i-a31-wdt";
+			reg = <0x01c20ca0 0x20>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		uart0: serial@01c28000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28000 0x400>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&bus_gates 112>;
+			resets = <&apb2_rst 16>;
+			dmas = <&dma 6>, <&dma 6>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart1: serial@01c28400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28400 0x400>;
+			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&bus_gates 113>;
+			resets = <&apb2_rst 17>;
+			dmas = <&dma 7>, <&dma 7>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart2: serial@01c28800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28800 0x400>;
+			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&bus_gates 114>;
+			resets = <&apb2_rst 18>;
+			dmas = <&dma 8>, <&dma 8>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart3: serial@01c28c00 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28c00 0x400>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&bus_gates 115>;
+			resets = <&apb2_rst 19>;
+			dmas = <&dma 9>, <&dma 9>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		gic: interrupt-controller@01c81000 {
+			compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+			reg = <0x01c81000 0x1000>,
+			      <0x01c82000 0x1000>,
+			      <0x01c84000 0x2000>,
+			      <0x01c86000 0x2000>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		rtc: rtc@01f00000 {
+			compatible = "allwinner,sun6i-a31-rtc";
+			reg = <0x01f00000 0x54>;
+			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+		};
+	};
+};

arch/arm/boot/dts/sun9i-a80-cubieboard4.dts

@@ -62,9 +62,31 @@ chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins_cubieboard4>;
+
+		green {
+			label = "cubieboard4:green:usr";
+			gpios = <&pio 7 17 GPIO_ACTIVE_HIGH>; /* PH17 */
+		};
+
+		red {
+			label = "cubieboard4:red:usr";
+			gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+		};
+	};
 };
 
 &pio {
+	led_pins_cubieboard4: led-pins@0 {
+		allwinner,pins = "PH6", "PH17";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
 	mmc0_cd_pin_cubieboard4: mmc0_cd_pin@0 {
 		allwinner,pins = "PH18";
 		allwinner,function = "gpio_in";
@@ -92,6 +114,14 @@ &mmc2 {
 	status = "okay";
 };
 
+&r_ir {
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;

arch/arm/boot/dts/sun9i-a80-optimus.dts

@@ -65,7 +65,7 @@ chosen {
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins_optimus>;
+		pinctrl-0 = <&led_pins_optimus>, <&led_r_pins_optimus>;
 
 		/* The LED names match those found on the board */
 
@@ -74,7 +74,10 @@ led2 {
 			gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>;
 		};
 
-		/* led3 is on PM15, in R_PIO */
+		led3 {
+			label = "optimus:led3:usr";
+			gpios = <&r_pio 1 15 GPIO_ACTIVE_HIGH>; /* PM15 */
+		};
 
 		led4 {
 			label = "optimus:led4:usr";
@@ -180,6 +183,23 @@ &reg_usb1_vbus {
 	status = "okay";
 };
 
+&r_ir {
+	status = "okay";
+};
+
+&r_pio {
+	led_r_pins_optimus: led-pins@1 {
+		allwinner,pins = "PM15";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+};
+
+&r_rsb {
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;

arch/arm/boot/dts/sun9i-a80.dtsi

@@ -128,6 +128,17 @@ clocks {
 		 */
 		ranges = <0 0 0 0x20000000>;
 
+		/*
+		 * This clock is actually configurable from the PRCM address
+		 * space. The external 24M oscillator can be turned off, and
+		 * the clock switched to an internal 16M RC oscillator. Under
+		 * normal operation there's no reason to do this, and the
+		 * default is to use the external good one, so just model this
+		 * as a fixed clock. Also it is not entirely clear if the
+		 * osc24M mux in the PRCM affects the entire clock tree, which
+		 * would also throw all the PLL clock rates off, or just the
+		 * downstream clocks in the PRCM.
+		 */
 		osc24M: osc24M_clk {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
@@ -135,6 +146,13 @@ osc24M: osc24M_clk {
 			clock-output-names = "osc24M";
 		};
 
+		/*
+		 * The 32k clock is from an external source, normally the
+		 * AC100 codec/RTC chip. This clock is by default enabled
+		 * and clocked at 32768 Hz, from the oscillator connected
+		 * to the AC100. It is configurable, but no such driver or
+		 * bindings exist yet.
+		 */
 		osc32k: osc32k_clk {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
@@ -164,6 +182,14 @@ usb_phy_clk: clk@00a08004 {
 					     "usb_phy2", "usb_hsic_12M";
 		};
 
+		pll3: clk@06000008 {
+			/* placeholder until implemented */
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-rate = <0>;
+			clock-output-names = "pll3";
+		};
+
 		pll4: clk@0600000c {
 			#clock-cells = <0>;
 			compatible = "allwinner,sun9i-a80-pll4-clk";
@@ -350,6 +376,68 @@ apb1_gates: clk@06000594 {
 					"apb1_uart2", "apb1_uart3",
 					"apb1_uart4", "apb1_uart5";
 		};
+
+		cpus_clk: clk@08001410 {
+			compatible = "allwinner,sun9i-a80-cpus-clk";
+			reg = <0x08001410 0x4>;
+			#clock-cells = <0>;
+			clocks = <&osc32k>, <&osc24M>, <&pll4>, <&pll3>;
+			clock-output-names = "cpus";
+		};
+
+		ahbs: ahbs_clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clock-div = <1>;
+			clock-mult = <1>;
+			clocks = <&cpus_clk>;
+			clock-output-names = "ahbs";
+		};
+
+		apbs: clk@0800141c {
+			compatible = "allwinner,sun8i-a23-apb0-clk";
+			reg = <0x0800141c 0x4>;
+			#clock-cells = <0>;
+			clocks = <&ahbs>;
+			clock-output-names = "apbs";
+		};
+
+		apbs_gates: clk@08001428 {
+			compatible = "allwinner,sun9i-a80-apbs-gates-clk";
+			reg = <0x08001428 0x4>;
+			#clock-cells = <1>;
+			clocks = <&apbs>;
+			clock-indices = <0>, <1>,
+					<2>, <3>,
+					<4>, <5>,
+					<6>, <7>,
+					<12>, <13>,
+					<16>, <17>,
+					<18>, <20>;
+			clock-output-names = "apbs_pio", "apbs_ir",
+					"apbs_timer", "apbs_rsb",
+					"apbs_uart", "apbs_1wire",
+					"apbs_i2c0", "apbs_i2c1",
+					"apbs_ps2_0", "apbs_ps2_1",
+					"apbs_dma", "apbs_i2s0",
+					"apbs_i2s1", "apbs_twd";
+		};
+
+		r_1wire_clk: clk@08001450 {
+			reg = <0x08001450 0x4>;
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-mod0-clk";
+			clocks = <&osc32k>, <&osc24M>;
+			clock-output-names = "r_1wire";
+		};
+
+		r_ir_clk: clk@08001454 {
+			reg = <0x08001454 0x4>;
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-mod0-clk";
+			clocks = <&osc32k>, <&osc24M>;
+			clock-output-names = "r_ir";
+		};
 	};
 
 	soc {
@@ -764,14 +852,83 @@ r_wdt: watchdog@08001000 {
 			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
+		apbs_rst: reset@080014b0 {
+			reg = <0x080014b0 0x4>;
+			compatible = "allwinner,sun6i-a31-clock-reset";
+			#reset-cells = <1>;
+		};
+
+		nmi_intc: interrupt-controller@080015a0 {
+			compatible = "allwinner,sun9i-a80-nmi";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <0x080015a0 0xc>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		r_ir: ir@08002000 {
+			compatible = "allwinner,sun5i-a13-ir";
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&r_ir_pins>;
+			clocks = <&apbs_gates 1>, <&r_ir_clk>;
+			clock-names = "apb", "ir";
+			resets = <&apbs_rst 1>;
+			reg = <0x08002000 0x40>;
+			status = "disabled";
+		};
+
 		r_uart: serial@08002800 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x08002800 0x400>;
 			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&osc24M>;
+			clocks = <&apbs_gates 4>;
+			resets = <&apbs_rst 4>;
+			status = "disabled";
+		};
+
+		r_pio: pinctrl@08002c00 {
+			compatible = "allwinner,sun9i-a80-r-pinctrl";
+			reg = <0x08002c00 0x400>;
+			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&apbs_gates 0>;
+			resets = <&apbs_rst 0>;
+			gpio-controller;
+			interrupt-controller;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#gpio-cells = <3>;
+
+			r_ir_pins: r_ir {
+				allwinner,pins = "PL6";
+				allwinner,function = "s_cir_rx";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			r_rsb_pins: r_rsb {
+				allwinner,pins = "PN0", "PN1";
+				allwinner,function = "s_rsb";
+				allwinner,drive = <SUN4I_PINCTRL_20_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+			};
+		};
+
+		r_rsb: i2c@08003400 {
+			compatible = "allwinner,sun8i-a23-rsb";
+			reg = <0x08003400 0x400>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&apbs_gates 3>;
+			clock-frequency = <3000000>;
+			resets = <&apbs_rst 3>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&r_rsb_pins>;
 			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
 		};
 	};
 };