Commit 7484c727 authored by Linus Walleij's avatar Linus Walleij

ARM: realview: delete the RealView board files

The device tree boot is now feature-complete and fully working,
so remove all the RealView board files. Move the remaining
realview_cpu_die() function frome "core.h" to the new "hotplug.h"
and leave just a minimal device tree core.
Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
parent 29b4817d
...@@ -4,16 +4,6 @@ ...@@ -4,16 +4,6 @@
ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include \ ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include \
-I$(srctree)/arch/arm/plat-versatile/include -I$(srctree)/arch/arm/plat-versatile/include
obj-y := core.o
obj-$(CONFIG_REALVIEW_DT) += realview-dt.o obj-$(CONFIG_REALVIEW_DT) += realview-dt.o
obj-$(CONFIG_SMP) += platsmp-dt.o obj-$(CONFIG_SMP) += platsmp-dt.o
ifdef CONFIG_ATAGS
obj-$(CONFIG_MACH_REALVIEW_EB) += realview_eb.o
obj-$(CONFIG_MACH_REALVIEW_PB11MP) += realview_pb11mp.o
obj-$(CONFIG_MACH_REALVIEW_PB1176) += realview_pb1176.o
obj-$(CONFIG_MACH_REALVIEW_PBA8) += realview_pba8.o
obj-$(CONFIG_MACH_REALVIEW_PBX) += realview_pbx.o
obj-$(CONFIG_SMP) += platsmp.o
endif
obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
/*
* Copyright (C) 2007 ARM Limited
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
* MA 02110-1301, USA.
*/
#ifndef __ASM_ARCH_BOARD_EB_H
#define __ASM_ARCH_BOARD_EB_H
#include "platform.h"
/*
* RealView EB + ARM11MPCore peripheral addresses
*/
#define REALVIEW_EB_UART0_BASE 0x10009000 /* UART 0 */
#define REALVIEW_EB_UART1_BASE 0x1000A000 /* UART 1 */
#define REALVIEW_EB_UART2_BASE 0x1000B000 /* UART 2 */
#define REALVIEW_EB_UART3_BASE 0x1000C000 /* UART 3 */
#define REALVIEW_EB_SSP_BASE 0x1000D000 /* Synchronous Serial Port */
#define REALVIEW_EB_WATCHDOG_BASE 0x10010000 /* watchdog interface */
#define REALVIEW_EB_TIMER0_1_BASE 0x10011000 /* Timer 0 and 1 */
#define REALVIEW_EB_TIMER2_3_BASE 0x10012000 /* Timer 2 and 3 */
#define REALVIEW_EB_GPIO0_BASE 0x10013000 /* GPIO port 0 */
#define REALVIEW_EB_RTC_BASE 0x10017000 /* Real Time Clock */
#define REALVIEW_EB_CLCD_BASE 0x10020000 /* CLCD */
#define REALVIEW_EB_GIC_CPU_BASE 0x10040000 /* Generic interrupt controller CPU interface */
#define REALVIEW_EB_GIC_DIST_BASE 0x10041000 /* Generic interrupt controller distributor */
#define REALVIEW_EB_SMC_BASE 0x10080000 /* Static memory controller */
#define REALVIEW_EB_FLASH_BASE 0x40000000
#define REALVIEW_EB_FLASH_SIZE SZ_64M
#define REALVIEW_EB_ETH_BASE 0x4E000000 /* Ethernet */
#define REALVIEW_EB_USB_BASE 0x4F000000 /* USB */
#ifdef CONFIG_REALVIEW_EB_ARM11MP_REVB
#define REALVIEW_EB11MP_PRIV_MEM_BASE 0x10100000
#define REALVIEW_EB11MP_L220_BASE 0x10102000 /* L220 registers */
#define REALVIEW_EB11MP_SYS_PLD_CTRL1 0xD8 /* Register offset for MPCore sysctl */
#else
#define REALVIEW_EB11MP_PRIV_MEM_BASE 0x1F000000
#define REALVIEW_EB11MP_L220_BASE 0x1F002000 /* L220 registers */
#define REALVIEW_EB11MP_SYS_PLD_CTRL1 0x74 /* Register offset for MPCore sysctl */
#endif
#define REALVIEW_EB11MP_PRIV_MEM_SIZE SZ_8K
#define REALVIEW_EB11MP_PRIV_MEM_OFF(x) (REALVIEW_EB11MP_PRIV_MEM_BASE + (x))
#define REALVIEW_EB11MP_SCU_BASE REALVIEW_EB11MP_PRIV_MEM_OFF(0) /* SCU registers */
#define REALVIEW_EB11MP_GIC_CPU_BASE REALVIEW_EB11MP_PRIV_MEM_OFF(0x0100) /* Generic interrupt controller CPU interface */
#define REALVIEW_EB11MP_TWD_BASE REALVIEW_EB11MP_PRIV_MEM_OFF(0x0600)
#define REALVIEW_EB11MP_GIC_DIST_BASE REALVIEW_EB11MP_PRIV_MEM_OFF(0x1000) /* Generic interrupt controller distributor */
/*
* Core tile identification (REALVIEW_SYS_PROCID)
*/
#define REALVIEW_EB_PROC_MASK 0xFF000000
#define REALVIEW_EB_PROC_ARM7TDMI 0x00000000
#define REALVIEW_EB_PROC_ARM9 0x02000000
#define REALVIEW_EB_PROC_ARM11 0x04000000
#define REALVIEW_EB_PROC_ARM11MP 0x06000000
#define REALVIEW_EB_PROC_A9MP 0x0C000000
#define check_eb_proc(proc_type) \
((readl(__io_address(REALVIEW_SYS_PROCID)) & REALVIEW_EB_PROC_MASK) \
== proc_type)
#ifdef CONFIG_REALVIEW_EB_ARM11MP
#define core_tile_eb11mp() check_eb_proc(REALVIEW_EB_PROC_ARM11MP)
#else
#define core_tile_eb11mp() 0
#endif
#ifdef CONFIG_REALVIEW_EB_A9MP
#define core_tile_a9mp() check_eb_proc(REALVIEW_EB_PROC_A9MP)
#else
#define core_tile_a9mp() 0
#endif
#define machine_is_realview_eb_mp() \
(machine_is_realview_eb() && (core_tile_eb11mp() || core_tile_a9mp()))
#endif /* __ASM_ARCH_BOARD_EB_H */
/*
* Copyright (C) 2008 ARM Limited
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
* MA 02110-1301, USA.
*/
#ifndef __ASM_ARCH_BOARD_PB1176_H
#define __ASM_ARCH_BOARD_PB1176_H
#include "platform.h"
/*
* Peripheral addresses
*/
#define REALVIEW_PB1176_UART4_BASE 0x10009000 /* UART 4 */
#define REALVIEW_PB1176_SCTL_BASE 0x10100000 /* System controller */
#define REALVIEW_PB1176_SMC_BASE 0x10111000 /* SMC */
#define REALVIEW_PB1176_DMC_BASE 0x10109000 /* DMC configuration */
#define REALVIEW_PB1176_SDRAM67_BASE 0x70000000 /* SDRAM banks 6 and 7 */
#define REALVIEW_PB1176_FLASH_BASE 0x30000000
#define REALVIEW_PB1176_FLASH_SIZE SZ_64M
#define REALVIEW_PB1176_SEC_FLASH_BASE 0x3C000000 /* Secure flash */
#define REALVIEW_PB1176_SEC_FLASH_SIZE SZ_64M
#define REALVIEW_PB1176_TIMER0_1_BASE 0x10104000 /* Timer 0 and 1 */
#define REALVIEW_PB1176_TIMER2_3_BASE 0x10105000 /* Timer 2 and 3 */
#define REALVIEW_PB1176_TIMER4_5_BASE 0x10106000 /* Timer 4 and 5 */
#define REALVIEW_PB1176_WATCHDOG_BASE 0x10107000 /* watchdog interface */
#define REALVIEW_PB1176_RTC_BASE 0x10108000 /* Real Time Clock */
#define REALVIEW_PB1176_GPIO0_BASE 0x1010A000 /* GPIO port 0 */
#define REALVIEW_PB1176_SSP_BASE 0x1010B000 /* Synchronous Serial Port */
#define REALVIEW_PB1176_UART0_BASE 0x1010C000 /* UART 0 */
#define REALVIEW_PB1176_UART1_BASE 0x1010D000 /* UART 1 */
#define REALVIEW_PB1176_UART2_BASE 0x1010E000 /* UART 2 */
#define REALVIEW_PB1176_UART3_BASE 0x1010F000 /* UART 3 */
#define REALVIEW_PB1176_CLCD_BASE 0x10112000 /* CLCD */
#define REALVIEW_PB1176_ETH_BASE 0x3A000000 /* Ethernet */
#define REALVIEW_PB1176_USB_BASE 0x3B000000 /* USB */
/*
* PCI regions
*/
#define REALVIEW_PB1176_PCI_BASE 0x60000000 /* PCI self config */
#define REALVIEW_PB1176_PCI_CFG_BASE 0x61000000 /* PCI config */
#define REALVIEW_PB1176_PCI_IO_BASE0 0x62000000 /* PCI IO region */
#define REALVIEW_PB1176_PCI_MEM_BASE0 0x63000000 /* Memory region 1 */
#define REALVIEW_PB1176_PCI_MEM_BASE1 0x64000000 /* Memory region 2 */
#define REALVIEW_PB1176_PCI_MEM_BASE2 0x68000000 /* Memory region 3 */
#define REALVIEW_PB1176_PCI_BASE_SIZE 0x01000000 /* 16MB */
#define REALVIEW_PB1176_PCI_CFG_BASE_SIZE 0x01000000 /* 16MB */
#define REALVIEW_PB1176_PCI_IO_BASE0_SIZE 0x01000000 /* 16MB */
#define REALVIEW_PB1176_PCI_MEM_BASE0_SIZE 0x01000000 /* 16MB */
#define REALVIEW_PB1176_PCI_MEM_BASE1_SIZE 0x04000000 /* 64MB */
#define REALVIEW_PB1176_PCI_MEM_BASE2_SIZE 0x08000000 /* 128MB */
#define REALVIEW_DC1176_GIC_CPU_BASE 0x10120000 /* GIC CPU interface, on devchip */
#define REALVIEW_DC1176_GIC_DIST_BASE 0x10121000 /* GIC distributor, on devchip */
#define REALVIEW_DC1176_ROM_BASE 0x10200000 /* 16KiB NRAM preudo-ROM, on devchip */
#define REALVIEW_PB1176_GIC_CPU_BASE 0x10040000 /* GIC CPU interface, on FPGA */
#define REALVIEW_PB1176_GIC_DIST_BASE 0x10041000 /* GIC distributor, on FPGA */
#define REALVIEW_PB1176_L220_BASE 0x10110000 /* L220 registers */
/*
* Control register SYS_RESETCTL Bit 8 is set to 1 to force a soft reset
*/
#define REALVIEW_PB1176_SYS_SOFT_RESET 0x0100
#endif /* __ASM_ARCH_BOARD_PB1176_H */
/*
* Copyright (C) 2008 ARM Limited
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
* MA 02110-1301, USA.
*/
#ifndef __ASM_ARCH_BOARD_PB11MP_H
#define __ASM_ARCH_BOARD_PB11MP_H
#include "platform.h"
/*
* Peripheral addresses
*/
#define REALVIEW_PB11MP_UART0_BASE 0x10009000 /* UART 0 */
#define REALVIEW_PB11MP_UART1_BASE 0x1000A000 /* UART 1 */
#define REALVIEW_PB11MP_UART2_BASE 0x1000B000 /* UART 2 */
#define REALVIEW_PB11MP_UART3_BASE 0x1000C000 /* UART 3 */
#define REALVIEW_PB11MP_SSP_BASE 0x1000D000 /* Synchronous Serial Port */
#define REALVIEW_PB11MP_WATCHDOG0_BASE 0x1000F000 /* Watchdog 0 */
#define REALVIEW_PB11MP_WATCHDOG_BASE 0x10010000 /* watchdog interface */
#define REALVIEW_PB11MP_TIMER0_1_BASE 0x10011000 /* Timer 0 and 1 */
#define REALVIEW_PB11MP_TIMER2_3_BASE 0x10012000 /* Timer 2 and 3 */
#define REALVIEW_PB11MP_GPIO0_BASE 0x10013000 /* GPIO port 0 */
#define REALVIEW_PB11MP_RTC_BASE 0x10017000 /* Real Time Clock */
#define REALVIEW_PB11MP_TIMER4_5_BASE 0x10018000 /* Timer 4/5 */
#define REALVIEW_PB11MP_TIMER6_7_BASE 0x10019000 /* Timer 6/7 */
#define REALVIEW_PB11MP_SCTL_BASE 0x1001A000 /* System Controller */
#define REALVIEW_PB11MP_CLCD_BASE 0x10020000 /* CLCD */
#define REALVIEW_PB11MP_ONB_SRAM_BASE 0x10060000 /* On-board SRAM */
#define REALVIEW_PB11MP_DMC_BASE 0x100E0000 /* DMC configuration */
#define REALVIEW_PB11MP_SMC_BASE 0x100E1000 /* SMC configuration */
#define REALVIEW_PB11MP_CAN_BASE 0x100E2000 /* CAN bus */
#define REALVIEW_PB11MP_CF_BASE 0x18000000 /* Compact flash */
#define REALVIEW_PB11MP_CF_MEM_BASE 0x18003000 /* SMC for Compact flash */
#define REALVIEW_PB11MP_GIC_CPU_BASE 0x1E000000 /* Generic interrupt controller CPU interface */
#define REALVIEW_PB11MP_FLASH0_BASE 0x40000000
#define REALVIEW_PB11MP_FLASH0_SIZE SZ_64M
#define REALVIEW_PB11MP_FLASH1_BASE 0x44000000
#define REALVIEW_PB11MP_FLASH1_SIZE SZ_64M
#define REALVIEW_PB11MP_ETH_BASE 0x4E000000 /* Ethernet */
#define REALVIEW_PB11MP_USB_BASE 0x4F000000 /* USB */
#define REALVIEW_PB11MP_GIC_DIST_BASE 0x1E001000 /* Generic interrupt controller distributor */
#define REALVIEW_PB11MP_LT_BASE 0xC0000000 /* Logic Tile expansion */
#define REALVIEW_PB11MP_SDRAM6_BASE 0x70000000 /* SDRAM bank 6 256MB */
#define REALVIEW_PB11MP_SDRAM7_BASE 0x80000000 /* SDRAM bank 7 256MB */
#define REALVIEW_PB11MP_SYS_PLD_CTRL1 0x74
/*
* PB11MPCore PCI regions
*/
#define REALVIEW_PB11MP_PCI_BASE 0x90040000 /* PCI-X Unit base */
#define REALVIEW_PB11MP_PCI_IO_BASE 0x90050000 /* IO Region on AHB */
#define REALVIEW_PB11MP_PCI_MEM_BASE 0xA0000000 /* MEM Region on AHB */
#define REALVIEW_PB11MP_PCI_BASE_SIZE 0x10000 /* 16 Kb */
#define REALVIEW_PB11MP_PCI_IO_SIZE 0x1000 /* 4 Kb */
#define REALVIEW_PB11MP_PCI_MEM_SIZE 0x20000000 /* 512 MB */
/*
* Testchip peripheral and fpga gic regions
*/
#define REALVIEW_TC11MP_PRIV_MEM_BASE 0x1F000000
#define REALVIEW_TC11MP_PRIV_MEM_SIZE SZ_8K
#define REALVIEW_TC11MP_SCU_BASE 0x1F000000 /* IRQ, Test chip */
#define REALVIEW_TC11MP_GIC_CPU_BASE 0x1F000100 /* Test chip interrupt controller CPU interface */
#define REALVIEW_TC11MP_TWD_BASE 0x1F000600
#define REALVIEW_TC11MP_GIC_DIST_BASE 0x1F001000 /* Test chip interrupt controller distributor */
#define REALVIEW_TC11MP_L220_BASE 0x1F002000 /* L220 registers */
/*
* Values for REALVIEW_SYS_RESET_CTRL
*/
#define REALVIEW_PB11MP_SYS_CTRL_RESET_CONFIGCLR 0x01
#define REALVIEW_PB11MP_SYS_CTRL_RESET_CONFIGINIT 0x02
#define REALVIEW_PB11MP_SYS_CTRL_RESET_DLLRESET 0x03
#define REALVIEW_PB11MP_SYS_CTRL_RESET_PLLRESET 0x04
#define REALVIEW_PB11MP_SYS_CTRL_RESET_POR 0x05
#define REALVIEW_PB11MP_SYS_CTRL_RESET_DoC 0x06
#define REALVIEW_PB11MP_SYS_CTRL_LED (1 << 0)
#endif /* __ASM_ARCH_BOARD_PB11MP_H */
/*
* Copyright (C) 2008 ARM Limited
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
* MA 02110-1301, USA.
*/
#ifndef __ASM_ARCH_BOARD_PBA8_H
#define __ASM_ARCH_BOARD_PBA8_H
#include "platform.h"
/*
* Peripheral addresses
*/
#define REALVIEW_PBA8_UART0_BASE 0x10009000 /* UART 0 */
#define REALVIEW_PBA8_UART1_BASE 0x1000A000 /* UART 1 */
#define REALVIEW_PBA8_UART2_BASE 0x1000B000 /* UART 2 */
#define REALVIEW_PBA8_UART3_BASE 0x1000C000 /* UART 3 */
#define REALVIEW_PBA8_SSP_BASE 0x1000D000 /* Synchronous Serial Port */
#define REALVIEW_PBA8_WATCHDOG0_BASE 0x1000F000 /* Watchdog 0 */
#define REALVIEW_PBA8_WATCHDOG_BASE 0x10010000 /* watchdog interface */
#define REALVIEW_PBA8_TIMER0_1_BASE 0x10011000 /* Timer 0 and 1 */
#define REALVIEW_PBA8_TIMER2_3_BASE 0x10012000 /* Timer 2 and 3 */
#define REALVIEW_PBA8_GPIO0_BASE 0x10013000 /* GPIO port 0 */
#define REALVIEW_PBA8_RTC_BASE 0x10017000 /* Real Time Clock */
#define REALVIEW_PBA8_TIMER4_5_BASE 0x10018000 /* Timer 4/5 */
#define REALVIEW_PBA8_TIMER6_7_BASE 0x10019000 /* Timer 6/7 */
#define REALVIEW_PBA8_SCTL_BASE 0x1001A000 /* System Controller */
#define REALVIEW_PBA8_CLCD_BASE 0x10020000 /* CLCD */
#define REALVIEW_PBA8_ONB_SRAM_BASE 0x10060000 /* On-board SRAM */
#define REALVIEW_PBA8_DMC_BASE 0x100E0000 /* DMC configuration */
#define REALVIEW_PBA8_SMC_BASE 0x100E1000 /* SMC configuration */
#define REALVIEW_PBA8_CAN_BASE 0x100E2000 /* CAN bus */
#define REALVIEW_PBA8_GIC_CPU_BASE 0x1E000000 /* Generic interrupt controller CPU interface */
#define REALVIEW_PBA8_FLASH0_BASE 0x40000000
#define REALVIEW_PBA8_FLASH0_SIZE SZ_64M
#define REALVIEW_PBA8_FLASH1_BASE 0x44000000
#define REALVIEW_PBA8_FLASH1_SIZE SZ_64M
#define REALVIEW_PBA8_ETH_BASE 0x4E000000 /* Ethernet */
#define REALVIEW_PBA8_USB_BASE 0x4F000000 /* USB */
#define REALVIEW_PBA8_GIC_DIST_BASE 0x1E001000 /* Generic interrupt controller distributor */
#define REALVIEW_PBA8_LT_BASE 0xC0000000 /* Logic Tile expansion */
#define REALVIEW_PBA8_SDRAM6_BASE 0x70000000 /* SDRAM bank 6 256MB */
#define REALVIEW_PBA8_SDRAM7_BASE 0x80000000 /* SDRAM bank 7 256MB */
#define REALVIEW_PBA8_SYS_PLD_CTRL1 0x74
/*
* PBA8 PCI regions
*/
#define REALVIEW_PBA8_PCI_BASE 0x90040000 /* PCI-X Unit base */
#define REALVIEW_PBA8_PCI_IO_BASE 0x90050000 /* IO Region on AHB */
#define REALVIEW_PBA8_PCI_MEM_BASE 0xA0000000 /* MEM Region on AHB */
#define REALVIEW_PBA8_PCI_BASE_SIZE 0x10000 /* 16 Kb */
#define REALVIEW_PBA8_PCI_IO_SIZE 0x1000 /* 4 Kb */
#define REALVIEW_PBA8_PCI_MEM_SIZE 0x20000000 /* 512 MB */
#endif /* __ASM_ARCH_BOARD_PBA8_H */
/*
* Copyright (C) 2009 ARM Limited
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#ifndef __ASM_ARCH_BOARD_PBX_H
#define __ASM_ARCH_BOARD_PBX_H
#include "platform.h"
/*
* Peripheral addresses
*/
#define REALVIEW_PBX_UART0_BASE 0x10009000 /* UART 0 */
#define REALVIEW_PBX_UART1_BASE 0x1000A000 /* UART 1 */
#define REALVIEW_PBX_UART2_BASE 0x1000B000 /* UART 2 */
#define REALVIEW_PBX_UART3_BASE 0x1000C000 /* UART 3 */
#define REALVIEW_PBX_SSP_BASE 0x1000D000 /* Synchronous Serial Port */
#define REALVIEW_PBX_WATCHDOG0_BASE 0x1000F000 /* Watchdog 0 */
#define REALVIEW_PBX_WATCHDOG_BASE 0x10010000 /* watchdog interface */
#define REALVIEW_PBX_TIMER0_1_BASE 0x10011000 /* Timer 0 and 1 */
#define REALVIEW_PBX_TIMER2_3_BASE 0x10012000 /* Timer 2 and 3 */
#define REALVIEW_PBX_GPIO0_BASE 0x10013000 /* GPIO port 0 */
#define REALVIEW_PBX_RTC_BASE 0x10017000 /* Real Time Clock */
#define REALVIEW_PBX_TIMER4_5_BASE 0x10018000 /* Timer 4/5 */
#define REALVIEW_PBX_TIMER6_7_BASE 0x10019000 /* Timer 6/7 */
#define REALVIEW_PBX_SCTL_BASE 0x1001A000 /* System Controller */
#define REALVIEW_PBX_CLCD_BASE 0x10020000 /* CLCD */
#define REALVIEW_PBX_ONB_SRAM_BASE 0x10060000 /* On-board SRAM */
#define REALVIEW_PBX_DMC_BASE 0x100E0000 /* DMC configuration */
#define REALVIEW_PBX_SMC_BASE 0x100E1000 /* SMC configuration */
#define REALVIEW_PBX_CAN_BASE 0x100E2000 /* CAN bus */
#define REALVIEW_PBX_GIC_CPU_BASE 0x1E000000 /* Generic interrupt controller CPU interface */
#define REALVIEW_PBX_FLASH0_BASE 0x40000000
#define REALVIEW_PBX_FLASH0_SIZE SZ_64M
#define REALVIEW_PBX_FLASH1_BASE 0x44000000
#define REALVIEW_PBX_FLASH1_SIZE SZ_64M
#define REALVIEW_PBX_ETH_BASE 0x4E000000 /* Ethernet */
#define REALVIEW_PBX_USB_BASE 0x4F000000 /* USB */
#define REALVIEW_PBX_GIC_DIST_BASE 0x1E001000 /* Generic interrupt controller distributor */
#define REALVIEW_PBX_LT_BASE 0xC0000000 /* Logic Tile expansion */
#define REALVIEW_PBX_SDRAM6_BASE 0x70000000 /* SDRAM bank 6 256MB */
#define REALVIEW_PBX_SDRAM7_BASE 0x80000000 /* SDRAM bank 7 256MB */
/*
* Tile-specific addresses
*/
#define REALVIEW_PBX_TILE_SCU_BASE 0x1F000000 /* SCU registers */
#define REALVIEW_PBX_TILE_GIC_CPU_BASE 0x1F000100 /* Private Generic interrupt controller CPU interface */
#define REALVIEW_PBX_TILE_TWD_BASE 0x1F000600
#define REALVIEW_PBX_TILE_TWD_PERCPU_BASE 0x1F000700
#define REALVIEW_PBX_TILE_TWD_SIZE 0x00000100
#define REALVIEW_PBX_TILE_GIC_DIST_BASE 0x1F001000 /* Private Generic interrupt controller distributor */
#define REALVIEW_PBX_TILE_L220_BASE 0x1F002000 /* L220 registers */
#define REALVIEW_PBX_SYS_PLD_CTRL1 0x74
/*
* PBX PCI regions
*/
#define REALVIEW_PBX_PCI_BASE 0x90040000 /* PCI-X Unit base */
#define REALVIEW_PBX_PCI_IO_BASE 0x90050000 /* IO Region on AHB */
#define REALVIEW_PBX_PCI_MEM_BASE 0xA0000000 /* MEM Region on AHB */
#define REALVIEW_PBX_PCI_BASE_SIZE 0x10000 /* 16 Kb */
#define REALVIEW_PBX_PCI_IO_SIZE 0x1000 /* 4 Kb */
#define REALVIEW_PBX_PCI_MEM_SIZE 0x20000000 /* 512 MB */
/*
* Core tile identification (REALVIEW_SYS_PROCID)
*/
#define REALVIEW_PBX_PROC_MASK 0xFF000000
#define REALVIEW_PBX_PROC_ARM7TDMI 0x00000000
#define REALVIEW_PBX_PROC_ARM9 0x02000000
#define REALVIEW_PBX_PROC_ARM11 0x04000000
#define REALVIEW_PBX_PROC_ARM11MP 0x06000000
#define REALVIEW_PBX_PROC_A9MP 0x0C000000
#define REALVIEW_PBX_PROC_A8 0x0E000000
#define check_pbx_proc(proc_type) \
((readl(__io_address(REALVIEW_SYS_PROCID)) & REALVIEW_PBX_PROC_MASK) \
== proc_type)
#ifdef CONFIG_MACH_REALVIEW_PBX
#define core_tile_pbx11mp() check_pbx_proc(REALVIEW_PBX_PROC_ARM11MP)
#define core_tile_pbxa9mp() check_pbx_proc(REALVIEW_PBX_PROC_A9MP)
#define core_tile_pbxa8() check_pbx_proc(REALVIEW_PBX_PROC_A8)
#else
#define core_tile_pbx11mp() 0
#define core_tile_pbxa9mp() 0
#define core_tile_pbxa8() 0
#endif
#endif /* __ASM_ARCH_BOARD_PBX_H */
/*
* linux/arch/arm/mach-realview/core.c
*
* Copyright (C) 1999 - 2003 ARM Limited
* Copyright (C) 2000 Deep Blue Solutions Ltd
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
#include <linux/device.h>
#include <linux/interrupt.h>
#include <linux/amba/bus.h>
#include <linux/amba/clcd.h>
#include <linux/platform_data/video-clcd-versatile.h>
#include <linux/io.h>
#include <linux/smsc911x.h>
#include <linux/smc91x.h>
#include <linux/ata_platform.h>
#include <linux/amba/mmci.h>
#include <linux/gfp.h>
#include <linux/mtd/physmap.h>
#include <linux/memblock.h>
#include <clocksource/timer-sp804.h>
#include "hardware.h"
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/hardware/icst.h>
#include <asm/mach/arch.h>
#include <asm/mach/irq.h>
#include <asm/mach/map.h>
#include "platform.h"
#include <plat/sched_clock.h>
#include "core.h"
#define REALVIEW_FLASHCTRL (__io_address(REALVIEW_SYS_BASE) + REALVIEW_SYS_FLASH_OFFSET)
static void realview_flash_set_vpp(struct platform_device *pdev, int on)
{
u32 val;
val = __raw_readl(REALVIEW_FLASHCTRL);
if (on)
val |= REALVIEW_FLASHPROG_FLVPPEN;
else
val &= ~REALVIEW_FLASHPROG_FLVPPEN;
__raw_writel(val, REALVIEW_FLASHCTRL);
}
static struct physmap_flash_data realview_flash_data = {
.width = 4,
.set_vpp = realview_flash_set_vpp,
};
struct platform_device realview_flash_device = {
.name = "physmap-flash",
.id = 0,
.dev = {
.platform_data = &realview_flash_data,
},
};
int realview_flash_register(struct resource *res, u32 num)
{
realview_flash_device.resource = res;
realview_flash_device.num_resources = num;
return platform_device_register(&realview_flash_device);
}
static struct smsc911x_platform_config smsc911x_config = {
.flags = SMSC911X_USE_32BIT,
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_HIGH,
.irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL,
.phy_interface = PHY_INTERFACE_MODE_MII,
};
static struct smc91x_platdata smc91x_platdata = {
.flags = SMC91X_USE_32BIT | SMC91X_NOWAIT,
};
static struct platform_device realview_eth_device = {
.name = "smsc911x",
.id = 0,
.num_resources = 2,
};
int realview_eth_register(const char *name, struct resource *res)
{
if (name)
realview_eth_device.name = name;
realview_eth_device.resource = res;
if (strcmp(realview_eth_device.name, "smsc911x") == 0)
realview_eth_device.dev.platform_data = &smsc911x_config;
else
realview_eth_device.dev.platform_data = &smc91x_platdata;
return platform_device_register(&realview_eth_device);
}
struct platform_device realview_usb_device = {
.name = "isp1760",
.num_resources = 2,
};
int realview_usb_register(struct resource *res)
{
realview_usb_device.resource = res;
return platform_device_register(&realview_usb_device);
}
static struct pata_platform_info pata_platform_data = {
.ioport_shift = 1,
};
static struct resource pata_resources[] = {
[0] = {
.start = REALVIEW_CF_BASE,
.end = REALVIEW_CF_BASE + 0xff,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = REALVIEW_CF_BASE + 0x100,
.end = REALVIEW_CF_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
},
};
struct platform_device realview_cf_device = {
.name = "pata_platform",
.id = -1,
.num_resources = ARRAY_SIZE(pata_resources),
.resource = pata_resources,
.dev = {
.platform_data = &pata_platform_data,
},
};
static struct resource realview_leds_resources[] = {
{
.start = REALVIEW_SYS_BASE + REALVIEW_SYS_LED_OFFSET,
.end = REALVIEW_SYS_BASE + REALVIEW_SYS_LED_OFFSET + 4,
.flags = IORESOURCE_MEM,
},
};
struct platform_device realview_leds_device = {
.name = "versatile-leds",
.id = -1,
.num_resources = ARRAY_SIZE(realview_leds_resources),
.resource = realview_leds_resources,
};
static struct resource realview_i2c_resource = {
.start = REALVIEW_I2C_BASE,
.end = REALVIEW_I2C_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
};
struct platform_device realview_i2c_device = {
.name = "versatile-i2c",
.id = 0,
.num_resources = 1,
.resource = &realview_i2c_resource,
};
static struct i2c_board_info realview_i2c_board_info[] = {
{
I2C_BOARD_INFO("ds1338", 0xd0 >> 1),
},
};
static int __init realview_i2c_init(void)
{
return i2c_register_board_info(0, realview_i2c_board_info,
ARRAY_SIZE(realview_i2c_board_info));
}
arch_initcall(realview_i2c_init);
#define REALVIEW_SYSMCI (__io_address(REALVIEW_SYS_BASE) + REALVIEW_SYS_MCI_OFFSET)
/*
* This is only used if GPIOLIB support is disabled
*/
static unsigned int realview_mmc_status(struct device *dev)
{
struct amba_device *adev = container_of(dev, struct amba_device, dev);
u32 mask;
if (machine_is_realview_pb1176()) {
static bool inserted = false;
/*
* The PB1176 does not have the status register,
* assume it is inserted at startup, then invert
* for each call so card insertion/removal will
* be detected anyway. This will not be called if
* GPIO on PL061 is active, which is the proper
* way to do this on the PB1176.
*/
inserted = !inserted;
return inserted ? 0 : 1;
}
if (adev->res.start == REALVIEW_MMCI0_BASE)
mask = 1;
else
mask = 2;
return readl(REALVIEW_SYSMCI) & mask;
}
struct mmci_platform_data realview_mmc0_plat_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.status = realview_mmc_status,
.gpio_wp = 17,
.gpio_cd = 16,
.cd_invert = true,
};
struct mmci_platform_data realview_mmc1_plat_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.status = realview_mmc_status,
.gpio_wp = 19,
.gpio_cd = 18,
.cd_invert = true,
};
void __init realview_init_early(void)
{
void __iomem *sys = __io_address(REALVIEW_SYS_BASE);
versatile_sched_clock_init(sys + REALVIEW_SYS_24MHz_OFFSET, 24000000);
}
/*
* CLCD support.
*/
#define SYS_CLCD_NLCDIOON (1 << 2)
#define SYS_CLCD_VDDPOSSWITCH (1 << 3)
#define SYS_CLCD_PWR3V5SWITCH (1 << 4)
#define SYS_CLCD_ID_MASK (0x1f << 8)
#define SYS_CLCD_ID_SANYO_3_8 (0x00 << 8)
#define SYS_CLCD_ID_UNKNOWN_8_4 (0x01 << 8)
#define SYS_CLCD_ID_EPSON_2_2 (0x02 << 8)
#define SYS_CLCD_ID_SANYO_2_5 (0x07 << 8)
#define SYS_CLCD_ID_VGA (0x1f << 8)
/*
* Disable all display connectors on the interface module.
*/
static void realview_clcd_disable(struct clcd_fb *fb)
{
void __iomem *sys_clcd = __io_address(REALVIEW_SYS_BASE) + REALVIEW_SYS_CLCD_OFFSET;
u32 val;
val = readl(sys_clcd);
val &= ~SYS_CLCD_NLCDIOON | SYS_CLCD_PWR3V5SWITCH;
writel(val, sys_clcd);
}
/*
* Enable the relevant connector on the interface module.
*/
static void realview_clcd_enable(struct clcd_fb *fb)
{
void __iomem *sys_clcd = __io_address(REALVIEW_SYS_BASE) + REALVIEW_SYS_CLCD_OFFSET;
u32 val;
/*
* Enable the PSUs
*/
val = readl(sys_clcd);
val |= SYS_CLCD_NLCDIOON | SYS_CLCD_PWR3V5SWITCH;
writel(val, sys_clcd);
}
/*
* Detect which LCD panel is connected, and return the appropriate
* clcd_panel structure. Note: we do not have any information on
* the required timings for the 8.4in panel, so we presently assume
* VGA timings.
*/
static int realview_clcd_setup(struct clcd_fb *fb)
{
void __iomem *sys_clcd = __io_address(REALVIEW_SYS_BASE) + REALVIEW_SYS_CLCD_OFFSET;
const char *panel_name, *vga_panel_name;
unsigned long framesize;
u32 val;
if (machine_is_realview_eb()) {
/* VGA, 16bpp */
framesize = 640 * 480 * 2;
vga_panel_name = "VGA";
} else {
/* XVGA, 16bpp */
framesize = 1024 * 768 * 2;
vga_panel_name = "XVGA";
}
val = readl(sys_clcd) & SYS_CLCD_ID_MASK;
if (val == SYS_CLCD_ID_SANYO_3_8)
panel_name = "Sanyo TM38QV67A02A";
else if (val == SYS_CLCD_ID_SANYO_2_5)
panel_name = "Sanyo QVGA Portrait";
else if (val == SYS_CLCD_ID_EPSON_2_2)
panel_name = "Epson L2F50113T00";
else if (val == SYS_CLCD_ID_VGA)
panel_name = vga_panel_name;
else {
pr_err("CLCD: unknown LCD panel ID 0x%08x, using VGA\n", val);
panel_name = vga_panel_name;
}
fb->panel = versatile_clcd_get_panel(panel_name);
if (!fb->panel)
return -EINVAL;
return versatile_clcd_setup_dma(fb, framesize);
}
struct clcd_board clcd_plat_data = {
.name = "RealView",
.caps = CLCD_CAP_ALL,
.check = clcdfb_check,
.decode = clcdfb_decode,
.disable = realview_clcd_disable,
.enable = realview_clcd_enable,
.setup = realview_clcd_setup,
.mmap = versatile_clcd_mmap_dma,
.remove = versatile_clcd_remove_dma,
};
/*
* Where is the timer (VA)?
*/
void __iomem *timer0_va_base;
void __iomem *timer1_va_base;
void __iomem *timer2_va_base;
void __iomem *timer3_va_base;
/*
* Set up the clock source and clock events devices
*/
void __init realview_timer_init(unsigned int timer_irq)
{
u32 val;
/*
* set clock frequency:
* REALVIEW_REFCLK is 32KHz
* REALVIEW_TIMCLK is 1MHz
*/
val = readl(__io_address(REALVIEW_SCTL_BASE));
writel((REALVIEW_TIMCLK << REALVIEW_TIMER1_EnSel) |
(REALVIEW_TIMCLK << REALVIEW_TIMER2_EnSel) |
(REALVIEW_TIMCLK << REALVIEW_TIMER3_EnSel) |
(REALVIEW_TIMCLK << REALVIEW_TIMER4_EnSel) | val,
__io_address(REALVIEW_SCTL_BASE));
/*
* Initialise to a known state (all timers off)
*/
sp804_timer_disable(timer0_va_base);
sp804_timer_disable(timer1_va_base);
sp804_timer_disable(timer2_va_base);
sp804_timer_disable(timer3_va_base);
sp804_clocksource_init(timer3_va_base, "timer3");
sp804_clockevents_init(timer0_va_base, timer_irq, "timer0");
}
/*
* Setup the memory banks.
*/
void realview_fixup(struct tag *tags, char **from)
{
/*
* Most RealView platforms have 512MB contiguous RAM at 0x70000000.
* Half of this is mirrored at 0.
*/
#ifdef CONFIG_REALVIEW_HIGH_PHYS_OFFSET
memblock_add(0x70000000, SZ_512M);
#else
memblock_add(0, SZ_256M);
#endif
}
/*
* Copyright (C) 2004 ARM Limited
* Copyright (C) 2000 Deep Blue Solutions Ltd
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#ifndef __ASM_ARCH_REALVIEW_H
#define __ASM_ARCH_REALVIEW_H
#include <linux/amba/bus.h>
#include <linux/io.h>
#include <asm/setup.h>
#define APB_DEVICE(name, busid, base, plat) \
static AMBA_APB_DEVICE(name, busid, 0, REALVIEW_##base##_BASE, base##_IRQ, plat)
#define AHB_DEVICE(name, busid, base, plat) \
static AMBA_AHB_DEVICE(name, busid, 0, REALVIEW_##base##_BASE, base##_IRQ, plat)
struct machine_desc;
extern struct platform_device realview_flash_device;
extern struct platform_device realview_cf_device;
extern struct platform_device realview_leds_device;
extern struct platform_device realview_i2c_device;
extern struct mmci_platform_data realview_mmc0_plat_data;
extern struct mmci_platform_data realview_mmc1_plat_data;
extern struct clcd_board clcd_plat_data;
extern void __iomem *timer0_va_base;
extern void __iomem *timer1_va_base;
extern void __iomem *timer2_va_base;
extern void __iomem *timer3_va_base;
extern void realview_timer_init(unsigned int timer_irq);
extern int realview_flash_register(struct resource *res, u32 num);
extern int realview_eth_register(const char *name, struct resource *res);
extern int realview_usb_register(struct resource *res);
extern void realview_init_early(void);
extern void realview_fixup(struct tag *tags, char **from);
extern const struct smp_operations realview_smp_ops;
extern void realview_cpu_die(unsigned int cpu);
#endif
/*
* This file contains the hardware definitions of the RealView boards.
*
* Copyright (C) 2003 ARM Limited.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#ifndef __ASM_ARCH_HARDWARE_H
#define __ASM_ARCH_HARDWARE_H
#include <asm/sizes.h>
/* macro to get at IO space when running virtually */
#ifdef CONFIG_MMU
/*
* Statically mapped addresses:
*
* 10xx xxxx -> fbxx xxxx
* 1exx xxxx -> fdxx xxxx
* 1fxx xxxx -> fexx xxxx
*/
#define IO_ADDRESS(x) (((x) & 0x03ffffff) + 0xfb000000)
#else
#define IO_ADDRESS(x) (x)
#endif
#define __io_address(n) IOMEM(IO_ADDRESS(n))
#endif
void realview_cpu_die(unsigned int cpu);
/*
* Copyright (C) 2007 ARM Limited
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
* MA 02110-1301, USA.
*/
#ifndef __MACH_IRQS_EB_H
#define __MACH_IRQS_EB_H
#define IRQ_LOCALTIMER 29
#define IRQ_EB_GIC_START 32
/*
* RealView EB interrupt sources
*/
#define IRQ_EB_WDOG (IRQ_EB_GIC_START + 0) /* Watchdog timer */
#define IRQ_EB_SOFT (IRQ_EB_GIC_START + 1) /* Software interrupt */
#define IRQ_EB_COMMRx (IRQ_EB_GIC_START + 2) /* Debug Comm Rx interrupt */
#define IRQ_EB_COMMTx (IRQ_EB_GIC_START + 3) /* Debug Comm Tx interrupt */
#define IRQ_EB_TIMER0_1 (IRQ_EB_GIC_START + 4) /* Timer 0 and 1 */
#define IRQ_EB_TIMER2_3 (IRQ_EB_GIC_START + 5) /* Timer 2 and 3 */
#define IRQ_EB_GPIO0 (IRQ_EB_GIC_START + 6) /* GPIO 0 */
#define IRQ_EB_GPIO1 (IRQ_EB_GIC_START + 7) /* GPIO 1 */
#define IRQ_EB_GPIO2 (IRQ_EB_GIC_START + 8) /* GPIO 2 */
/* 9 reserved */
#define IRQ_EB_RTC (IRQ_EB_GIC_START + 10) /* Real Time Clock */
#define IRQ_EB_SSP (IRQ_EB_GIC_START + 11) /* Synchronous Serial Port */
#define IRQ_EB_UART0 (IRQ_EB_GIC_START + 12) /* UART 0 on development chip */
#define IRQ_EB_UART1 (IRQ_EB_GIC_START + 13) /* UART 1 on development chip */
#define IRQ_EB_UART2 (IRQ_EB_GIC_START + 14) /* UART 2 on development chip */
#define IRQ_EB_UART3 (IRQ_EB_GIC_START + 15) /* UART 3 on development chip */
#define IRQ_EB_SCI (IRQ_EB_GIC_START + 16) /* Smart Card Interface */
#define IRQ_EB_MMCI0A (IRQ_EB_GIC_START + 17) /* Multimedia Card 0A */
#define IRQ_EB_MMCI0B (IRQ_EB_GIC_START + 18) /* Multimedia Card 0B */
#define IRQ_EB_AACI (IRQ_EB_GIC_START + 19) /* Audio Codec */
#define IRQ_EB_KMI0 (IRQ_EB_GIC_START + 20) /* Keyboard/Mouse port 0 */
#define IRQ_EB_KMI1 (IRQ_EB_GIC_START + 21) /* Keyboard/Mouse port 1 */
#define IRQ_EB_CHARLCD (IRQ_EB_GIC_START + 22) /* Character LCD */
#define IRQ_EB_CLCD (IRQ_EB_GIC_START + 23) /* CLCD controller */
#define IRQ_EB_DMA (IRQ_EB_GIC_START + 24) /* DMA controller */
#define IRQ_EB_PWRFAIL (IRQ_EB_GIC_START + 25) /* Power failure */
#define IRQ_EB_PISMO (IRQ_EB_GIC_START + 26) /* PISMO interface */
#define IRQ_EB_DoC (IRQ_EB_GIC_START + 27) /* Disk on Chip memory controller */
#define IRQ_EB_ETH (IRQ_EB_GIC_START + 28) /* Ethernet controller */
#define IRQ_EB_USB (IRQ_EB_GIC_START + 29) /* USB controller */
#define IRQ_EB_TSPEN (IRQ_EB_GIC_START + 30) /* Touchscreen pen */
#define IRQ_EB_TSKPAD (IRQ_EB_GIC_START + 31) /* Touchscreen keypad */
/*
* RealView EB + ARM11MPCore interrupt sources (primary GIC on the core tile)
*/
#define IRQ_EB11MP_AACI (IRQ_EB_GIC_START + 0)
#define IRQ_EB11MP_TIMER0_1 (IRQ_EB_GIC_START + 1)
#define IRQ_EB11MP_TIMER2_3 (IRQ_EB_GIC_START + 2)
#define IRQ_EB11MP_USB (IRQ_EB_GIC_START + 3)
#define IRQ_EB11MP_UART0 (IRQ_EB_GIC_START + 4)
#define IRQ_EB11MP_UART1 (IRQ_EB_GIC_START + 5)
#define IRQ_EB11MP_RTC (IRQ_EB_GIC_START + 6)
#define IRQ_EB11MP_KMI0 (IRQ_EB_GIC_START + 7)
#define IRQ_EB11MP_KMI1 (IRQ_EB_GIC_START + 8)
#define IRQ_EB11MP_ETH (IRQ_EB_GIC_START + 9)
#define IRQ_EB11MP_EB_IRQ1 (IRQ_EB_GIC_START + 10) /* main GIC */
#define IRQ_EB11MP_EB_IRQ2 (IRQ_EB_GIC_START + 11) /* tile GIC */
#define IRQ_EB11MP_EB_FIQ1 (IRQ_EB_GIC_START + 12) /* main GIC */
#define IRQ_EB11MP_EB_FIQ2 (IRQ_EB_GIC_START + 13) /* tile GIC */
#define IRQ_EB11MP_MMCI0A (IRQ_EB_GIC_START + 14)
#define IRQ_EB11MP_MMCI0B (IRQ_EB_GIC_START + 15)
#define IRQ_EB11MP_PMU_CPU0 (IRQ_EB_GIC_START + 17)
#define IRQ_EB11MP_PMU_CPU1 (IRQ_EB_GIC_START + 18)
#define IRQ_EB11MP_PMU_CPU2 (IRQ_EB_GIC_START + 19)
#define IRQ_EB11MP_PMU_CPU3 (IRQ_EB_GIC_START + 20)
#define IRQ_EB11MP_PMU_SCU0 (IRQ_EB_GIC_START + 21)
#define IRQ_EB11MP_PMU_SCU1 (IRQ_EB_GIC_START + 22)
#define IRQ_EB11MP_PMU_SCU2 (IRQ_EB_GIC_START + 23)
#define IRQ_EB11MP_PMU_SCU3 (IRQ_EB_GIC_START + 24)
#define IRQ_EB11MP_PMU_SCU4 (IRQ_EB_GIC_START + 25)
#define IRQ_EB11MP_PMU_SCU5 (IRQ_EB_GIC_START + 26)
#define IRQ_EB11MP_PMU_SCU6 (IRQ_EB_GIC_START + 27)
#define IRQ_EB11MP_PMU_SCU7 (IRQ_EB_GIC_START + 28)
#define IRQ_EB11MP_L220_EVENT (IRQ_EB_GIC_START + 29)
#define IRQ_EB11MP_L220_SLAVE (IRQ_EB_GIC_START + 30)
#define IRQ_EB11MP_L220_DECODE (IRQ_EB_GIC_START + 31)
/*
* The 11MPcore tile leaves the following unconnected.
*/
#define IRQ_EB11MP_UART2 0
#define IRQ_EB11MP_UART3 0
#define IRQ_EB11MP_CLCD 0
#define IRQ_EB11MP_DMA 0
#define IRQ_EB11MP_WDOG 0
#define IRQ_EB11MP_GPIO0 0
#define IRQ_EB11MP_GPIO1 0
#define IRQ_EB11MP_GPIO2 0
#define IRQ_EB11MP_SCI 0
#define IRQ_EB11MP_SSP 0
#define NR_GIC_EB11MP 2
#endif /* __MACH_IRQS_EB_H */
/*
* Copyright (C) 2008 ARM Limited
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
* MA 02110-1301, USA.
*/
#ifndef __MACH_IRQS_PB1176_H
#define __MACH_IRQS_PB1176_H
#define IRQ_DC1176_GIC_START 32
#define IRQ_PB1176_GIC_START 64
/*
* ARM1176 DevChip interrupt sources (primary GIC)
*/
#define IRQ_DC1176_WATCHDOG (IRQ_DC1176_GIC_START + 0) /* Watchdog timer */
#define IRQ_DC1176_SOFTINT (IRQ_DC1176_GIC_START + 1) /* Software interrupt */
#define IRQ_DC1176_COMMRx (IRQ_DC1176_GIC_START + 2) /* Debug Comm Rx interrupt */
#define IRQ_DC1176_COMMTx (IRQ_DC1176_GIC_START + 3) /* Debug Comm Tx interrupt */
#define IRQ_DC1176_CORE_PMU (IRQ_DC1176_GIC_START + 7) /* Core PMU interrupt */
#define IRQ_DC1176_TIMER0 (IRQ_DC1176_GIC_START + 8) /* Timer 0 */
#define IRQ_DC1176_TIMER1 (IRQ_DC1176_GIC_START + 9) /* Timer 1 */
#define IRQ_DC1176_TIMER2 (IRQ_DC1176_GIC_START + 10) /* Timer 2 */
#define IRQ_DC1176_APC (IRQ_DC1176_GIC_START + 11)
#define IRQ_DC1176_IEC (IRQ_DC1176_GIC_START + 12)
#define IRQ_DC1176_L2CC (IRQ_DC1176_GIC_START + 13)
#define IRQ_DC1176_RTC (IRQ_DC1176_GIC_START + 14)
#define IRQ_DC1176_CLCD (IRQ_DC1176_GIC_START + 15) /* CLCD controller */
#define IRQ_DC1176_GPIO0 (IRQ_DC1176_GIC_START + 16)
#define IRQ_DC1176_SSP (IRQ_DC1176_GIC_START + 17) /* SSP port */
#define IRQ_DC1176_UART0 (IRQ_DC1176_GIC_START + 18) /* UART 0 on development chip */
#define IRQ_DC1176_UART1 (IRQ_DC1176_GIC_START + 19) /* UART 1 on development chip */
#define IRQ_DC1176_UART2 (IRQ_DC1176_GIC_START + 20) /* UART 2 on development chip */
#define IRQ_DC1176_UART3 (IRQ_DC1176_GIC_START + 21) /* UART 3 on development chip */
#define IRQ_DC1176_PB_IRQ2 (IRQ_DC1176_GIC_START + 30) /* tile GIC */
#define IRQ_DC1176_PB_IRQ1 (IRQ_DC1176_GIC_START + 31) /* main GIC */
/*
* RealView PB1176 interrupt sources (secondary GIC)
*/
#define IRQ_PB1176_MMCI0A (IRQ_PB1176_GIC_START + 1) /* Multimedia Card 0A */
#define IRQ_PB1176_MMCI0B (IRQ_PB1176_GIC_START + 2) /* Multimedia Card 0A */
#define IRQ_PB1176_KMI0 (IRQ_PB1176_GIC_START + 3) /* Keyboard/Mouse port 0 */
#define IRQ_PB1176_KMI1 (IRQ_PB1176_GIC_START + 4) /* Keyboard/Mouse port 1 */
#define IRQ_PB1176_SCI (IRQ_PB1176_GIC_START + 5)
#define IRQ_PB1176_UART4 (IRQ_PB1176_GIC_START + 6) /* UART 4 on baseboard */
#define IRQ_PB1176_CHARLCD (IRQ_PB1176_GIC_START + 7) /* Character LCD */
#define IRQ_PB1176_GPIO1 (IRQ_PB1176_GIC_START + 8)
#define IRQ_PB1176_GPIO2 (IRQ_PB1176_GIC_START + 9)
#define IRQ_PB1176_ETH (IRQ_PB1176_GIC_START + 10) /* Ethernet controller */
#define IRQ_PB1176_USB (IRQ_PB1176_GIC_START + 11) /* USB controller */
#define IRQ_PB1176_PISMO (IRQ_PB1176_GIC_START + 16)
#define IRQ_PB1176_AACI (IRQ_PB1176_GIC_START + 19) /* Audio Codec */
#define IRQ_PB1176_TIMER0_1 (IRQ_PB1176_GIC_START + 22)
#define IRQ_PB1176_TIMER2_3 (IRQ_PB1176_GIC_START + 23)
#define IRQ_PB1176_DMAC (IRQ_PB1176_GIC_START + 24) /* DMA controller */
#define IRQ_PB1176_RTC (IRQ_PB1176_GIC_START + 25) /* Real Time Clock */
#define IRQ_PB1176_SCTL -1
#endif /* __MACH_IRQS_PB1176_H */
/*
* Copyright (C) 2008 ARM Limited
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
* MA 02110-1301, USA.
*/
#ifndef __MACH_IRQS_PB11MP_H
#define __MACH_IRQS_PB11MP_H
#define IRQ_LOCALTIMER 29
#define IRQ_TC11MP_GIC_START 32
#define IRQ_PB11MP_GIC_START 64
/*
* ARM11MPCore test chip interrupt sources (primary GIC on the test chip)
*/
#define IRQ_TC11MP_AACI (IRQ_TC11MP_GIC_START + 0)
#define IRQ_TC11MP_TIMER0_1 (IRQ_TC11MP_GIC_START + 1)
#define IRQ_TC11MP_TIMER2_3 (IRQ_TC11MP_GIC_START + 2)
#define IRQ_TC11MP_USB (IRQ_TC11MP_GIC_START + 3)
#define IRQ_TC11MP_UART0 (IRQ_TC11MP_GIC_START + 4)
#define IRQ_TC11MP_UART1 (IRQ_TC11MP_GIC_START + 5)
#define IRQ_TC11MP_RTC (IRQ_TC11MP_GIC_START + 6)
#define IRQ_TC11MP_KMI0 (IRQ_TC11MP_GIC_START + 7)
#define IRQ_TC11MP_KMI1 (IRQ_TC11MP_GIC_START + 8)
#define IRQ_TC11MP_ETH (IRQ_TC11MP_GIC_START + 9)
#define IRQ_TC11MP_PB_IRQ1 (IRQ_TC11MP_GIC_START + 10) /* main GIC */
#define IRQ_TC11MP_PB_IRQ2 (IRQ_TC11MP_GIC_START + 11) /* tile GIC */
#define IRQ_TC11MP_PB_FIQ1 (IRQ_TC11MP_GIC_START + 12) /* main GIC */
#define IRQ_TC11MP_PB_FIQ2 (IRQ_TC11MP_GIC_START + 13) /* tile GIC */
#define IRQ_TC11MP_MMCI0A (IRQ_TC11MP_GIC_START + 14)
#define IRQ_TC11MP_MMCI0B (IRQ_TC11MP_GIC_START + 15)
#define IRQ_TC11MP_PMU_CPU0 (IRQ_TC11MP_GIC_START + 17)
#define IRQ_TC11MP_PMU_CPU1 (IRQ_TC11MP_GIC_START + 18)
#define IRQ_TC11MP_PMU_CPU2 (IRQ_TC11MP_GIC_START + 19)
#define IRQ_TC11MP_PMU_CPU3 (IRQ_TC11MP_GIC_START + 20)
#define IRQ_TC11MP_PMU_SCU0 (IRQ_TC11MP_GIC_START + 21)
#define IRQ_TC11MP_PMU_SCU1 (IRQ_TC11MP_GIC_START + 22)
#define IRQ_TC11MP_PMU_SCU2 (IRQ_TC11MP_GIC_START + 23)
#define IRQ_TC11MP_PMU_SCU3 (IRQ_TC11MP_GIC_START + 24)
#define IRQ_TC11MP_PMU_SCU4 (IRQ_TC11MP_GIC_START + 25)
#define IRQ_TC11MP_PMU_SCU5 (IRQ_TC11MP_GIC_START + 26)
#define IRQ_TC11MP_PMU_SCU6 (IRQ_TC11MP_GIC_START + 27)
#define IRQ_TC11MP_PMU_SCU7 (IRQ_TC11MP_GIC_START + 28)
#define IRQ_TC11MP_L220_EVENT (IRQ_TC11MP_GIC_START + 29)
#define IRQ_TC11MP_L220_SLAVE (IRQ_TC11MP_GIC_START + 30)
#define IRQ_TC11MP_L220_DECODE (IRQ_TC11MP_GIC_START + 31)
/*
* RealView PB11MPCore GIC interrupt sources (secondary GIC on the board)
*/
#define IRQ_PB11MP_WATCHDOG (IRQ_PB11MP_GIC_START + 0) /* Watchdog timer */
#define IRQ_PB11MP_SOFT (IRQ_PB11MP_GIC_START + 1) /* Software interrupt */
#define IRQ_PB11MP_COMMRx (IRQ_PB11MP_GIC_START + 2) /* Debug Comm Rx interrupt */
#define IRQ_PB11MP_COMMTx (IRQ_PB11MP_GIC_START + 3) /* Debug Comm Tx interrupt */
#define IRQ_PB11MP_GPIO0 (IRQ_PB11MP_GIC_START + 6) /* GPIO 0 */
#define IRQ_PB11MP_GPIO1 (IRQ_PB11MP_GIC_START + 7) /* GPIO 1 */
#define IRQ_PB11MP_GPIO2 (IRQ_PB11MP_GIC_START + 8) /* GPIO 2 */
/* 9 reserved */
#define IRQ_PB11MP_RTC_GIC1 (IRQ_PB11MP_GIC_START + 10) /* Real Time Clock */
#define IRQ_PB11MP_SSP (IRQ_PB11MP_GIC_START + 11) /* Synchronous Serial Port */
#define IRQ_PB11MP_UART0_GIC1 (IRQ_PB11MP_GIC_START + 12) /* UART 0 on development chip */
#define IRQ_PB11MP_UART1_GIC1 (IRQ_PB11MP_GIC_START + 13) /* UART 1 on development chip */
#define IRQ_PB11MP_UART2 (IRQ_PB11MP_GIC_START + 14) /* UART 2 on development chip */
#define IRQ_PB11MP_UART3 (IRQ_PB11MP_GIC_START + 15) /* UART 3 on development chip */
#define IRQ_PB11MP_SCI (IRQ_PB11MP_GIC_START + 16) /* Smart Card Interface */
#define IRQ_PB11MP_MMCI0A_GIC1 (IRQ_PB11MP_GIC_START + 17) /* Multimedia Card 0A */
#define IRQ_PB11MP_MMCI0B_GIC1 (IRQ_PB11MP_GIC_START + 18) /* Multimedia Card 0B */
#define IRQ_PB11MP_AACI_GIC1 (IRQ_PB11MP_GIC_START + 19) /* Audio Codec */
#define IRQ_PB11MP_KMI0_GIC1 (IRQ_PB11MP_GIC_START + 20) /* Keyboard/Mouse port 0 */
#define IRQ_PB11MP_KMI1_GIC1 (IRQ_PB11MP_GIC_START + 21) /* Keyboard/Mouse port 1 */
#define IRQ_PB11MP_CHARLCD (IRQ_PB11MP_GIC_START + 22) /* Character LCD */
#define IRQ_PB11MP_CLCD (IRQ_PB11MP_GIC_START + 23) /* CLCD controller */
#define IRQ_PB11MP_DMAC (IRQ_PB11MP_GIC_START + 24) /* DMA controller */
#define IRQ_PB11MP_PWRFAIL (IRQ_PB11MP_GIC_START + 25) /* Power failure */
#define IRQ_PB11MP_PISMO (IRQ_PB11MP_GIC_START + 26) /* PISMO interface */
#define IRQ_PB11MP_DoC (IRQ_PB11MP_GIC_START + 27) /* Disk on Chip memory controller */
#define IRQ_PB11MP_ETH_GIC1 (IRQ_PB11MP_GIC_START + 28) /* Ethernet controller */
#define IRQ_PB11MP_USB_GIC1 (IRQ_PB11MP_GIC_START + 29) /* USB controller */
#define IRQ_PB11MP_TSPEN (IRQ_PB11MP_GIC_START + 30) /* Touchscreen pen */
#define IRQ_PB11MP_TSKPAD (IRQ_PB11MP_GIC_START + 31) /* Touchscreen keypad */
#endif /* __MACH_IRQS_PB11MP_H */
/*
* Copyright (C) 2008 ARM Limited
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
* MA 02110-1301, USA.
*/
#ifndef __MACH_IRQS_PBA8_H
#define __MACH_IRQS_PBA8_H
#define IRQ_PBA8_GIC_START 32
/*
* PB-A8 on-board gic irq sources
*/
#define IRQ_PBA8_WATCHDOG (IRQ_PBA8_GIC_START + 0) /* Watchdog timer */
#define IRQ_PBA8_SOFT (IRQ_PBA8_GIC_START + 1) /* Software interrupt */
#define IRQ_PBA8_COMMRx (IRQ_PBA8_GIC_START + 2) /* Debug Comm Rx interrupt */
#define IRQ_PBA8_COMMTx (IRQ_PBA8_GIC_START + 3) /* Debug Comm Tx interrupt */
#define IRQ_PBA8_TIMER0_1 (IRQ_PBA8_GIC_START + 4) /* Timer 0/1 (default timer) */
#define IRQ_PBA8_TIMER2_3 (IRQ_PBA8_GIC_START + 5) /* Timer 2/3 */
#define IRQ_PBA8_GPIO0 (IRQ_PBA8_GIC_START + 6) /* GPIO 0 */
#define IRQ_PBA8_GPIO1 (IRQ_PBA8_GIC_START + 7) /* GPIO 1 */
#define IRQ_PBA8_GPIO2 (IRQ_PBA8_GIC_START + 8) /* GPIO 2 */
/* 9 reserved */
#define IRQ_PBA8_RTC (IRQ_PBA8_GIC_START + 10) /* Real Time Clock */
#define IRQ_PBA8_SSP (IRQ_PBA8_GIC_START + 11) /* Synchronous Serial Port */
#define IRQ_PBA8_UART0 (IRQ_PBA8_GIC_START + 12) /* UART 0 on development chip */
#define IRQ_PBA8_UART1 (IRQ_PBA8_GIC_START + 13) /* UART 1 on development chip */
#define IRQ_PBA8_UART2 (IRQ_PBA8_GIC_START + 14) /* UART 2 on development chip */
#define IRQ_PBA8_UART3 (IRQ_PBA8_GIC_START + 15) /* UART 3 on development chip */
#define IRQ_PBA8_SCI (IRQ_PBA8_GIC_START + 16) /* Smart Card Interface */
#define IRQ_PBA8_MMCI0A (IRQ_PBA8_GIC_START + 17) /* Multimedia Card 0A */
#define IRQ_PBA8_MMCI0B (IRQ_PBA8_GIC_START + 18) /* Multimedia Card 0B */
#define IRQ_PBA8_AACI (IRQ_PBA8_GIC_START + 19) /* Audio Codec */
#define IRQ_PBA8_KMI0 (IRQ_PBA8_GIC_START + 20) /* Keyboard/Mouse port 0 */
#define IRQ_PBA8_KMI1 (IRQ_PBA8_GIC_START + 21) /* Keyboard/Mouse port 1 */
#define IRQ_PBA8_CHARLCD (IRQ_PBA8_GIC_START + 22) /* Character LCD */
#define IRQ_PBA8_CLCD (IRQ_PBA8_GIC_START + 23) /* CLCD controller */
#define IRQ_PBA8_DMAC (IRQ_PBA8_GIC_START + 24) /* DMA controller */
#define IRQ_PBA8_PWRFAIL (IRQ_PBA8_GIC_START + 25) /* Power failure */
#define IRQ_PBA8_PISMO (IRQ_PBA8_GIC_START + 26) /* PISMO interface */
#define IRQ_PBA8_DoC (IRQ_PBA8_GIC_START + 27) /* Disk on Chip memory controller */
#define IRQ_PBA8_ETH (IRQ_PBA8_GIC_START + 28) /* Ethernet controller */
#define IRQ_PBA8_USB (IRQ_PBA8_GIC_START + 29) /* USB controller */
#define IRQ_PBA8_TSPEN (IRQ_PBA8_GIC_START + 30) /* Touchscreen pen */
#define IRQ_PBA8_TSKPAD (IRQ_PBA8_GIC_START + 31) /* Touchscreen keypad */
#define IRQ_PBA8_PMU (IRQ_PBA8_GIC_START + 47) /* Cortex-A8 PMU */
/* ... */
#define IRQ_PBA8_PCI0 (IRQ_PBA8_GIC_START + 50)
#define IRQ_PBA8_PCI1 (IRQ_PBA8_GIC_START + 51)
#define IRQ_PBA8_PCI2 (IRQ_PBA8_GIC_START + 52)
#define IRQ_PBA8_PCI3 (IRQ_PBA8_GIC_START + 53)
#define IRQ_PBA8_SMC -1
#define IRQ_PBA8_SCTL -1
#endif /* __MACH_IRQS_PBA8_H */
/*
* Copyright (C) 2009 ARM Limited
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#ifndef __MACH_IRQS_PBX_H
#define __MACH_IRQS_PBX_H
#define IRQ_LOCALTIMER 29
#define IRQ_PBX_GIC_START 32
/*
* PBX on-board gic irq sources
*/
#define IRQ_PBX_WATCHDOG (IRQ_PBX_GIC_START + 0) /* Watchdog timer */
#define IRQ_PBX_SOFT (IRQ_PBX_GIC_START + 1) /* Software interrupt */
#define IRQ_PBX_COMMRx (IRQ_PBX_GIC_START + 2) /* Debug Comm Rx interrupt */
#define IRQ_PBX_COMMTx (IRQ_PBX_GIC_START + 3) /* Debug Comm Tx interrupt */
#define IRQ_PBX_TIMER0_1 (IRQ_PBX_GIC_START + 4) /* Timer 0/1 (default timer) */
#define IRQ_PBX_TIMER2_3 (IRQ_PBX_GIC_START + 5) /* Timer 2/3 */
#define IRQ_PBX_GPIO0 (IRQ_PBX_GIC_START + 6) /* GPIO 0 */
#define IRQ_PBX_GPIO1 (IRQ_PBX_GIC_START + 7) /* GPIO 1 */
#define IRQ_PBX_GPIO2 (IRQ_PBX_GIC_START + 8) /* GPIO 2 */
/* 9 reserved */
#define IRQ_PBX_RTC (IRQ_PBX_GIC_START + 10) /* Real Time Clock */
#define IRQ_PBX_SSP (IRQ_PBX_GIC_START + 11) /* Synchronous Serial Port */
#define IRQ_PBX_UART0 (IRQ_PBX_GIC_START + 12) /* UART 0 on development chip */
#define IRQ_PBX_UART1 (IRQ_PBX_GIC_START + 13) /* UART 1 on development chip */
#define IRQ_PBX_UART2 (IRQ_PBX_GIC_START + 14) /* UART 2 on development chip */
#define IRQ_PBX_UART3 (IRQ_PBX_GIC_START + 15) /* UART 3 on development chip */
#define IRQ_PBX_SCI (IRQ_PBX_GIC_START + 16) /* Smart Card Interface */
#define IRQ_PBX_MMCI0A (IRQ_PBX_GIC_START + 17) /* Multimedia Card 0A */
#define IRQ_PBX_MMCI0B (IRQ_PBX_GIC_START + 18) /* Multimedia Card 0B */
#define IRQ_PBX_AACI (IRQ_PBX_GIC_START + 19) /* Audio Codec */
#define IRQ_PBX_KMI0 (IRQ_PBX_GIC_START + 20) /* Keyboard/Mouse port 0 */
#define IRQ_PBX_KMI1 (IRQ_PBX_GIC_START + 21) /* Keyboard/Mouse port 1 */
#define IRQ_PBX_CHARLCD (IRQ_PBX_GIC_START + 22) /* Character LCD */
#define IRQ_PBX_CLCD (IRQ_PBX_GIC_START + 23) /* CLCD controller */
#define IRQ_PBX_DMAC (IRQ_PBX_GIC_START + 24) /* DMA controller */
#define IRQ_PBX_PWRFAIL (IRQ_PBX_GIC_START + 25) /* Power failure */
#define IRQ_PBX_PISMO (IRQ_PBX_GIC_START + 26) /* PISMO interface */
#define IRQ_PBX_DoC (IRQ_PBX_GIC_START + 27) /* Disk on Chip memory controller */
#define IRQ_PBX_ETH (IRQ_PBX_GIC_START + 28) /* Ethernet controller */
#define IRQ_PBX_USB (IRQ_PBX_GIC_START + 29) /* USB controller */
#define IRQ_PBX_TSPEN (IRQ_PBX_GIC_START + 30) /* Touchscreen pen */
#define IRQ_PBX_TSKPAD (IRQ_PBX_GIC_START + 31) /* Touchscreen keypad */
#define IRQ_PBX_PMU_SCU0 (IRQ_PBX_GIC_START + 32) /* SCU PMU Interrupts (11mp) */
#define IRQ_PBX_PMU_SCU1 (IRQ_PBX_GIC_START + 33)
#define IRQ_PBX_PMU_SCU2 (IRQ_PBX_GIC_START + 34)
#define IRQ_PBX_PMU_SCU3 (IRQ_PBX_GIC_START + 35)
#define IRQ_PBX_PMU_SCU4 (IRQ_PBX_GIC_START + 36)
#define IRQ_PBX_PMU_SCU5 (IRQ_PBX_GIC_START + 37)
#define IRQ_PBX_PMU_SCU6 (IRQ_PBX_GIC_START + 38)
#define IRQ_PBX_PMU_SCU7 (IRQ_PBX_GIC_START + 39)
#define IRQ_PBX_WATCHDOG1 (IRQ_PBX_GIC_START + 40) /* Watchdog1 timer */
#define IRQ_PBX_TIMER4_5 (IRQ_PBX_GIC_START + 41) /* Timer 0/1 (default timer) */
#define IRQ_PBX_TIMER6_7 (IRQ_PBX_GIC_START + 42) /* Timer 2/3 */
/* ... */
#define IRQ_PBX_PMU_CPU0 (IRQ_PBX_GIC_START + 44) /* CPU PMU Interrupts */
#define IRQ_PBX_PMU_CPU1 (IRQ_PBX_GIC_START + 45)
#define IRQ_PBX_PMU_CPU2 (IRQ_PBX_GIC_START + 46)
#define IRQ_PBX_PMU_CPU3 (IRQ_PBX_GIC_START + 47)
/* ... */
#define IRQ_PBX_PCI0 (IRQ_PBX_GIC_START + 50)
#define IRQ_PBX_PCI1 (IRQ_PBX_GIC_START + 51)
#define IRQ_PBX_PCI2 (IRQ_PBX_GIC_START + 52)
#define IRQ_PBX_PCI3 (IRQ_PBX_GIC_START + 53)
#define IRQ_PBX_SMC -1
#define IRQ_PBX_SCTL -1
#endif /* __MACH_IRQS_PBX_H */
/*
* Copyright (c) ARM Limited 2003. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#ifndef __ASM_ARCH_PLATFORM_H
#define __ASM_ARCH_PLATFORM_H
/*
* Memory definitions
*/
#define REALVIEW_BOOT_ROM_LO 0x30000000 /* DoC Base (64Mb)...*/
#define REALVIEW_BOOT_ROM_HI 0x30000000
#define REALVIEW_BOOT_ROM_BASE REALVIEW_BOOT_ROM_HI /* Normal position */
#define REALVIEW_BOOT_ROM_SIZE SZ_64M
#define REALVIEW_SSRAM_BASE /* REALVIEW_SSMC_BASE ? */
#define REALVIEW_SSRAM_SIZE SZ_2M
/*
* SDRAM
*/
#define REALVIEW_SDRAM_BASE 0x00000000
/*
* Logic expansion modules
*
*/
/* ------------------------------------------------------------------------
* RealView Registers
* ------------------------------------------------------------------------
*
*/
#define REALVIEW_SYS_ID_OFFSET 0x00
#define REALVIEW_SYS_SW_OFFSET 0x04
#define REALVIEW_SYS_LED_OFFSET 0x08
#define REALVIEW_SYS_OSC0_OFFSET 0x0C
#define REALVIEW_SYS_OSC1_OFFSET 0x10
#define REALVIEW_SYS_OSC2_OFFSET 0x14
#define REALVIEW_SYS_OSC3_OFFSET 0x18
#define REALVIEW_SYS_OSC4_OFFSET 0x1C /* OSC1 for RealView/AB */
#define REALVIEW_SYS_LOCK_OFFSET 0x20
#define REALVIEW_SYS_100HZ_OFFSET 0x24
#define REALVIEW_SYS_CFGDATA1_OFFSET 0x28
#define REALVIEW_SYS_CFGDATA2_OFFSET 0x2C
#define REALVIEW_SYS_FLAGS_OFFSET 0x30
#define REALVIEW_SYS_FLAGSSET_OFFSET 0x30
#define REALVIEW_SYS_FLAGSCLR_OFFSET 0x34
#define REALVIEW_SYS_NVFLAGS_OFFSET 0x38
#define REALVIEW_SYS_NVFLAGSSET_OFFSET 0x38
#define REALVIEW_SYS_NVFLAGSCLR_OFFSET 0x3C
#define REALVIEW_SYS_RESETCTL_OFFSET 0x40
#define REALVIEW_SYS_PCICTL_OFFSET 0x44
#define REALVIEW_SYS_MCI_OFFSET 0x48
#define REALVIEW_SYS_FLASH_OFFSET 0x4C
#define REALVIEW_SYS_CLCD_OFFSET 0x50
#define REALVIEW_SYS_CLCDSER_OFFSET 0x54
#define REALVIEW_SYS_BOOTCS_OFFSET 0x58
#define REALVIEW_SYS_24MHz_OFFSET 0x5C
#define REALVIEW_SYS_MISC_OFFSET 0x60
#define REALVIEW_SYS_IOSEL_OFFSET 0x70
#define REALVIEW_SYS_PROCID_OFFSET 0x84
#define REALVIEW_SYS_TEST_OSC0_OFFSET 0xC0
#define REALVIEW_SYS_TEST_OSC1_OFFSET 0xC4
#define REALVIEW_SYS_TEST_OSC2_OFFSET 0xC8
#define REALVIEW_SYS_TEST_OSC3_OFFSET 0xCC
#define REALVIEW_SYS_TEST_OSC4_OFFSET 0xD0
#define REALVIEW_SYS_BASE 0x10000000
#define REALVIEW_SYS_ID (REALVIEW_SYS_BASE + REALVIEW_SYS_ID_OFFSET)
#define REALVIEW_SYS_SW (REALVIEW_SYS_BASE + REALVIEW_SYS_SW_OFFSET)
#define REALVIEW_SYS_LED (REALVIEW_SYS_BASE + REALVIEW_SYS_LED_OFFSET)
#define REALVIEW_SYS_OSC0 (REALVIEW_SYS_BASE + REALVIEW_SYS_OSC0_OFFSET)
#define REALVIEW_SYS_OSC1 (REALVIEW_SYS_BASE + REALVIEW_SYS_OSC1_OFFSET)
#define REALVIEW_SYS_LOCK (REALVIEW_SYS_BASE + REALVIEW_SYS_LOCK_OFFSET)
#define REALVIEW_SYS_100HZ (REALVIEW_SYS_BASE + REALVIEW_SYS_100HZ_OFFSET)
#define REALVIEW_SYS_CFGDATA1 (REALVIEW_SYS_BASE + REALVIEW_SYS_CFGDATA1_OFFSET)
#define REALVIEW_SYS_CFGDATA2 (REALVIEW_SYS_BASE + REALVIEW_SYS_CFGDATA2_OFFSET)
#define REALVIEW_SYS_FLAGS (REALVIEW_SYS_BASE + REALVIEW_SYS_FLAGS_OFFSET)
#define REALVIEW_SYS_FLAGSSET (REALVIEW_SYS_BASE + REALVIEW_SYS_FLAGSSET_OFFSET)
#define REALVIEW_SYS_FLAGSCLR (REALVIEW_SYS_BASE + REALVIEW_SYS_FLAGSCLR_OFFSET)
#define REALVIEW_SYS_NVFLAGS (REALVIEW_SYS_BASE + REALVIEW_SYS_NVFLAGS_OFFSET)
#define REALVIEW_SYS_NVFLAGSSET (REALVIEW_SYS_BASE + REALVIEW_SYS_NVFLAGSSET_OFFSET)
#define REALVIEW_SYS_NVFLAGSCLR (REALVIEW_SYS_BASE + REALVIEW_SYS_NVFLAGSCLR_OFFSET)
#define REALVIEW_SYS_RESETCTL (REALVIEW_SYS_BASE + REALVIEW_SYS_RESETCTL_OFFSET)
#define REALVIEW_SYS_PCICTL (REALVIEW_SYS_BASE + REALVIEW_SYS_PCICTL_OFFSET)
#define REALVIEW_SYS_MCI (REALVIEW_SYS_BASE + REALVIEW_SYS_MCI_OFFSET)
#define REALVIEW_SYS_FLASH (REALVIEW_SYS_BASE + REALVIEW_SYS_FLASH_OFFSET)
#define REALVIEW_SYS_CLCD (REALVIEW_SYS_BASE + REALVIEW_SYS_CLCD_OFFSET)
#define REALVIEW_SYS_CLCDSER (REALVIEW_SYS_BASE + REALVIEW_SYS_CLCDSER_OFFSET)
#define REALVIEW_SYS_BOOTCS (REALVIEW_SYS_BASE + REALVIEW_SYS_BOOTCS_OFFSET)
#define REALVIEW_SYS_24MHz (REALVIEW_SYS_BASE + REALVIEW_SYS_24MHz_OFFSET)
#define REALVIEW_SYS_MISC (REALVIEW_SYS_BASE + REALVIEW_SYS_MISC_OFFSET)
#define REALVIEW_SYS_IOSEL (REALVIEW_SYS_BASE + REALVIEW_SYS_IOSEL_OFFSET)
#define REALVIEW_SYS_PROCID (REALVIEW_SYS_BASE + REALVIEW_SYS_PROCID_OFFSET)
#define REALVIEW_SYS_TEST_OSC0 (REALVIEW_SYS_BASE + REALVIEW_SYS_TEST_OSC0_OFFSET)
#define REALVIEW_SYS_TEST_OSC1 (REALVIEW_SYS_BASE + REALVIEW_SYS_TEST_OSC1_OFFSET)
#define REALVIEW_SYS_TEST_OSC2 (REALVIEW_SYS_BASE + REALVIEW_SYS_TEST_OSC2_OFFSET)
#define REALVIEW_SYS_TEST_OSC3 (REALVIEW_SYS_BASE + REALVIEW_SYS_TEST_OSC3_OFFSET)
#define REALVIEW_SYS_TEST_OSC4 (REALVIEW_SYS_BASE + REALVIEW_SYS_TEST_OSC4_OFFSET)
/* ------------------------------------------------------------------------
* RealView control registers
* ------------------------------------------------------------------------
*/
/*
* REALVIEW_IDFIELD
*
* 31:24 = manufacturer (0x41 = ARM)
* 23:16 = architecture (0x08 = AHB system bus, ASB processor bus)
* 15:12 = FPGA (0x3 = XVC600 or XVC600E)
* 11:4 = build value
* 3:0 = revision number (0x1 = rev B (AHB))
*/
/*
* REALVIEW_SYS_LOCK
* control access to SYS_OSCx, SYS_CFGDATAx, SYS_RESETCTL,
* SYS_CLD, SYS_BOOTCS
*/
#define REALVIEW_SYS_LOCK_LOCKED (1 << 16)
#define REALVIEW_SYS_LOCK_VAL 0xA05F /* Enable write access */
/*
* REALVIEW_SYS_FLASH
*/
#define REALVIEW_FLASHPROG_FLVPPEN (1 << 0) /* Enable writing to flash */
/*
* REALVIEW_INTREG
* - used to acknowledge and control MMCI and UART interrupts
*/
#define REALVIEW_INTREG_WPROT 0x00 /* MMC protection status (no interrupt generated) */
#define REALVIEW_INTREG_RI0 0x01 /* Ring indicator UART0 is asserted, */
#define REALVIEW_INTREG_CARDIN 0x08 /* MMCI card in detect */
/* write 1 to acknowledge and clear */
#define REALVIEW_INTREG_RI1 0x02 /* Ring indicator UART1 is asserted, */
#define REALVIEW_INTREG_CARDINSERT 0x03 /* Signal insertion of MMC card */
/*
* RealView common peripheral addresses
*/
#define REALVIEW_SCTL_BASE 0x10001000 /* System controller */
#define REALVIEW_I2C_BASE 0x10002000 /* I2C control */
#define REALVIEW_AACI_BASE 0x10004000 /* Audio */
#define REALVIEW_MMCI0_BASE 0x10005000 /* MMC interface */
#define REALVIEW_KMI0_BASE 0x10006000 /* KMI interface */
#define REALVIEW_KMI1_BASE 0x10007000 /* KMI 2nd interface */
#define REALVIEW_CHAR_LCD_BASE 0x10008000 /* Character LCD */
#define REALVIEW_SCI_BASE 0x1000E000 /* Smart card controller */
#define REALVIEW_GPIO1_BASE 0x10014000 /* GPIO port 1 */
#define REALVIEW_GPIO2_BASE 0x10015000 /* GPIO port 2 */
#define REALVIEW_DMC_BASE 0x10018000 /* DMC configuration */
#define REALVIEW_DMAC_BASE 0x10030000 /* DMA controller */
/* PCI space */
#define REALVIEW_PCI_BASE 0x41000000 /* PCI Interface */
#define REALVIEW_PCI_CFG_BASE 0x42000000
#define REALVIEW_PCI_MEM_BASE0 0x44000000
#define REALVIEW_PCI_MEM_BASE1 0x50000000
#define REALVIEW_PCI_MEM_BASE2 0x60000000
/* Sizes of above maps */
#define REALVIEW_PCI_BASE_SIZE 0x01000000
#define REALVIEW_PCI_CFG_BASE_SIZE 0x02000000
#define REALVIEW_PCI_MEM_BASE0_SIZE 0x0c000000 /* 32Mb */
#define REALVIEW_PCI_MEM_BASE1_SIZE 0x10000000 /* 256Mb */
#define REALVIEW_PCI_MEM_BASE2_SIZE 0x10000000 /* 256Mb */
#define REALVIEW_SDRAM67_BASE 0x70000000 /* SDRAM banks 6 and 7 */
#define REALVIEW_LT_BASE 0x80000000 /* Logic Tile expansion */
/*
* CompactFlash
*/
#define REALVIEW_CF_BASE 0x18000000 /* CompactFlash */
#define REALVIEW_CF_MEM_BASE 0x18003000 /* SMC for CompactFlash */
/*
* Disk on Chip
*/
#define REALVIEW_DOC_BASE 0x2C000000
#define REALVIEW_DOC_SIZE (16 << 20)
#define REALVIEW_DOC_PAGE_SIZE 512
#define REALVIEW_DOC_TOTAL_PAGES (DOC_SIZE / PAGE_SIZE)
#define ERASE_UNIT_PAGES 32
#define START_PAGE 0x80
/*
* LED settings, bits [7:0]
*/
#define REALVIEW_SYS_LED0 (1 << 0)
#define REALVIEW_SYS_LED1 (1 << 1)
#define REALVIEW_SYS_LED2 (1 << 2)
#define REALVIEW_SYS_LED3 (1 << 3)
#define REALVIEW_SYS_LED4 (1 << 4)
#define REALVIEW_SYS_LED5 (1 << 5)
#define REALVIEW_SYS_LED6 (1 << 6)
#define REALVIEW_SYS_LED7 (1 << 7)
#define ALL_LEDS 0xFF
#define LED_BANK REALVIEW_SYS_LED
/*
* Control registers
*/
#define REALVIEW_IDFIELD_OFFSET 0x0 /* RealView build information */
#define REALVIEW_FLASHPROG_OFFSET 0x4 /* Flash devices */
#define REALVIEW_INTREG_OFFSET 0x8 /* Interrupt control */
#define REALVIEW_DECODE_OFFSET 0xC /* Fitted logic modules */
/*
* System controller bit assignment
*/
#define REALVIEW_REFCLK 0
#define REALVIEW_TIMCLK 1
#define REALVIEW_TIMER1_EnSel 15
#define REALVIEW_TIMER2_EnSel 17
#define REALVIEW_TIMER3_EnSel 19
#define REALVIEW_TIMER4_EnSel 21
#define REALVIEW_CSR_BASE 0x10000000
#define REALVIEW_CSR_SIZE 0x10000000
#endif /* __ASM_ARCH_PLATFORM_H */
...@@ -17,8 +17,7 @@ ...@@ -17,8 +17,7 @@
#include <asm/smp_scu.h> #include <asm/smp_scu.h>
#include <plat/platsmp.h> #include <plat/platsmp.h>
#include "hotplug.h"
#include "core.h"
#define REALVIEW_SYS_FLAGSSET_OFFSET 0x30 #define REALVIEW_SYS_FLAGSSET_OFFSET 0x30
......
/*
* linux/arch/arm/mach-realview/platsmp.c
*
* Copyright (C) 2002 ARM Ltd.
* All Rights Reserved
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/init.h>
#include <linux/errno.h>
#include <linux/smp.h>
#include <linux/io.h>
#include "hardware.h"
#include <asm/mach-types.h>
#include <asm/smp_scu.h>
#include "board-eb.h"
#include "board-pb11mp.h"
#include "board-pbx.h"
#include <plat/platsmp.h>
#include "core.h"
static void __iomem *scu_base_addr(void)
{
if (machine_is_realview_eb_mp())
return __io_address(REALVIEW_EB11MP_SCU_BASE);
else if (machine_is_realview_pb11mp())
return __io_address(REALVIEW_TC11MP_SCU_BASE);
else if (machine_is_realview_pbx() &&
(core_tile_pbx11mp() || core_tile_pbxa9mp()))
return __io_address(REALVIEW_PBX_TILE_SCU_BASE);
else
return (void __iomem *)0;
}
/*
* Initialise the CPU possible map early - this describes the CPUs
* which may be present or become present in the system.
*/
static void __init realview_smp_init_cpus(void)
{
void __iomem *scu_base = scu_base_addr();
unsigned int i, ncores;
ncores = scu_base ? scu_get_core_count(scu_base) : 1;
/* sanity check */
if (ncores > nr_cpu_ids) {
pr_warn("SMP: %u cores greater than maximum (%u), clipping\n",
ncores, nr_cpu_ids);
ncores = nr_cpu_ids;
}
for (i = 0; i < ncores; i++)
set_cpu_possible(i, true);
}
static void __init realview_smp_prepare_cpus(unsigned int max_cpus)
{
scu_enable(scu_base_addr());
/*
* Write the address of secondary startup into the
* system-wide flags register. The BootMonitor waits
* until it receives a soft interrupt, and then the
* secondary CPU branches to this address.
*/
__raw_writel(virt_to_phys(versatile_secondary_startup),
__io_address(REALVIEW_SYS_FLAGSSET));
}
const struct smp_operations realview_smp_ops __initconst = {
.smp_init_cpus = realview_smp_init_cpus,
.smp_prepare_cpus = realview_smp_prepare_cpus,
.smp_secondary_init = versatile_secondary_init,
.smp_boot_secondary = versatile_boot_secondary,
#ifdef CONFIG_HOTPLUG_CPU
.cpu_die = realview_cpu_die,
#endif
};
/*
* linux/arch/arm/mach-realview/realview_eb.c
*
* Copyright (C) 2004 ARM Limited
* Copyright (C) 2000 Deep Blue Solutions Ltd
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/device.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl061.h>
#include <linux/amba/mmci.h>
#include <linux/amba/pl022.h>
#include <linux/io.h>
#include <linux/irqchip/arm-gic.h>
#include <linux/platform_data/clk-realview.h>
#include <linux/reboot.h>
#include "hardware.h"
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/pgtable.h>
#include <asm/hardware/cache-l2x0.h>
#include <asm/smp_twd.h>
#include <asm/system_info.h>
#include <asm/outercache.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/time.h>
#include "board-eb.h"
#include "irqs-eb.h"
#include "core.h"
static struct map_desc realview_eb_io_desc[] __initdata = {
{
.virtual = IO_ADDRESS(REALVIEW_SYS_BASE),
.pfn = __phys_to_pfn(REALVIEW_SYS_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_EB_GIC_CPU_BASE),
.pfn = __phys_to_pfn(REALVIEW_EB_GIC_CPU_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_EB_GIC_DIST_BASE),
.pfn = __phys_to_pfn(REALVIEW_EB_GIC_DIST_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_SCTL_BASE),
.pfn = __phys_to_pfn(REALVIEW_SCTL_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_EB_TIMER0_1_BASE),
.pfn = __phys_to_pfn(REALVIEW_EB_TIMER0_1_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_EB_TIMER2_3_BASE),
.pfn = __phys_to_pfn(REALVIEW_EB_TIMER2_3_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
},
#ifdef CONFIG_DEBUG_LL
{
.virtual = IO_ADDRESS(REALVIEW_EB_UART0_BASE),
.pfn = __phys_to_pfn(REALVIEW_EB_UART0_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}
#endif
};
static struct map_desc realview_eb11mp_io_desc[] __initdata = {
{
.virtual = IO_ADDRESS(REALVIEW_EB11MP_PRIV_MEM_BASE),
.pfn = __phys_to_pfn(REALVIEW_EB11MP_PRIV_MEM_BASE),
.length = REALVIEW_EB11MP_PRIV_MEM_SIZE,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_EB11MP_L220_BASE),
.pfn = __phys_to_pfn(REALVIEW_EB11MP_L220_BASE),
.length = SZ_8K,
.type = MT_DEVICE,
}
};
static void __init realview_eb_map_io(void)
{
iotable_init(realview_eb_io_desc, ARRAY_SIZE(realview_eb_io_desc));
if (core_tile_eb11mp() || core_tile_a9mp())
iotable_init(realview_eb11mp_io_desc, ARRAY_SIZE(realview_eb11mp_io_desc));
}
static struct pl061_platform_data gpio0_plat_data = {
.gpio_base = 0,
};
static struct pl061_platform_data gpio1_plat_data = {
.gpio_base = 8,
};
static struct pl061_platform_data gpio2_plat_data = {
.gpio_base = 16,
};
static struct pl022_ssp_controller ssp0_plat_data = {
.bus_id = 0,
.enable_dma = 0,
.num_chipselect = 1,
};
/*
* RealView EB AMBA devices
*/
/*
* These devices are connected via the core APB bridge
*/
#define GPIO2_IRQ { IRQ_EB_GPIO2 }
#define GPIO3_IRQ { IRQ_EB_GPIO3 }
#define AACI_IRQ { IRQ_EB_AACI }
#define MMCI0_IRQ { IRQ_EB_MMCI0A, IRQ_EB_MMCI0B }
#define KMI0_IRQ { IRQ_EB_KMI0 }
#define KMI1_IRQ { IRQ_EB_KMI1 }
/*
* These devices are connected directly to the multi-layer AHB switch
*/
#define EB_SMC_IRQ { }
#define MPMC_IRQ { }
#define EB_CLCD_IRQ { IRQ_EB_CLCD }
#define DMAC_IRQ { IRQ_EB_DMA }
/*
* These devices are connected via the core APB bridge
*/
#define SCTL_IRQ { }
#define EB_WATCHDOG_IRQ { IRQ_EB_WDOG }
#define EB_GPIO0_IRQ { IRQ_EB_GPIO0 }
#define GPIO1_IRQ { IRQ_EB_GPIO1 }
#define EB_RTC_IRQ { IRQ_EB_RTC }
/*
* These devices are connected via the DMA APB bridge
*/
#define SCI_IRQ { IRQ_EB_SCI }
#define EB_UART0_IRQ { IRQ_EB_UART0 }
#define EB_UART1_IRQ { IRQ_EB_UART1 }
#define EB_UART2_IRQ { IRQ_EB_UART2 }
#define EB_UART3_IRQ { IRQ_EB_UART3 }
#define EB_SSP_IRQ { IRQ_EB_SSP }
/* FPGA Primecells */
APB_DEVICE(aaci, "fpga:aaci", AACI, NULL);
APB_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
APB_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
APB_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
APB_DEVICE(uart3, "fpga:uart3", EB_UART3, NULL);
/* DevChip Primecells */
AHB_DEVICE(smc, "dev:smc", EB_SMC, NULL);
AHB_DEVICE(clcd, "dev:clcd", EB_CLCD, &clcd_plat_data);
AHB_DEVICE(dmac, "dev:dmac", DMAC, NULL);
AHB_DEVICE(sctl, "dev:sctl", SCTL, NULL);
APB_DEVICE(wdog, "dev:wdog", EB_WATCHDOG, NULL);
APB_DEVICE(gpio0, "dev:gpio0", EB_GPIO0, &gpio0_plat_data);
APB_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
APB_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
APB_DEVICE(rtc, "dev:rtc", EB_RTC, NULL);
APB_DEVICE(sci0, "dev:sci0", SCI, NULL);
APB_DEVICE(uart0, "dev:uart0", EB_UART0, NULL);
APB_DEVICE(uart1, "dev:uart1", EB_UART1, NULL);
APB_DEVICE(uart2, "dev:uart2", EB_UART2, NULL);
APB_DEVICE(ssp0, "dev:ssp0", EB_SSP, &ssp0_plat_data);
static struct amba_device *amba_devs[] __initdata = {
&dmac_device,
&uart0_device,
&uart1_device,
&uart2_device,
&uart3_device,
&smc_device,
&clcd_device,
&sctl_device,
&wdog_device,
&gpio0_device,
&gpio1_device,
&gpio2_device,
&rtc_device,
&sci0_device,
&ssp0_device,
&aaci_device,
&mmc0_device,
&kmi0_device,
&kmi1_device,
};
/*
* RealView EB platform devices
*/
static struct resource realview_eb_flash_resource = {
.start = REALVIEW_EB_FLASH_BASE,
.end = REALVIEW_EB_FLASH_BASE + REALVIEW_EB_FLASH_SIZE - 1,
.flags = IORESOURCE_MEM,
};
static struct resource realview_eb_eth_resources[] = {
[0] = {
.start = REALVIEW_EB_ETH_BASE,
.end = REALVIEW_EB_ETH_BASE + SZ_64K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = IRQ_EB_ETH,
.end = IRQ_EB_ETH,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
},
};
/*
* Detect and register the correct Ethernet device. RealView/EB rev D
* platforms use the newer SMSC LAN9118 Ethernet chip
*/
static int eth_device_register(void)
{
void __iomem *eth_addr = ioremap(REALVIEW_EB_ETH_BASE, SZ_4K);
const char *name = NULL;
u32 idrev;
if (!eth_addr)
return -ENOMEM;
idrev = readl(eth_addr + 0x50);
if ((idrev & 0xFFFF0000) != 0x01180000)
/* SMSC LAN9118 not present, use LAN91C111 instead */
name = "smc91x";
iounmap(eth_addr);
return realview_eth_register(name, realview_eb_eth_resources);
}
static struct resource realview_eb_isp1761_resources[] = {
[0] = {
.start = REALVIEW_EB_USB_BASE,
.end = REALVIEW_EB_USB_BASE + SZ_128K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = IRQ_EB_USB,
.end = IRQ_EB_USB,
.flags = IORESOURCE_IRQ,
},
};
static struct resource pmu_resources[] = {
[0] = {
.start = IRQ_EB11MP_PMU_CPU0,
.end = IRQ_EB11MP_PMU_CPU0,
.flags = IORESOURCE_IRQ,
},
[1] = {
.start = IRQ_EB11MP_PMU_CPU1,
.end = IRQ_EB11MP_PMU_CPU1,
.flags = IORESOURCE_IRQ,
},
[2] = {
.start = IRQ_EB11MP_PMU_CPU2,
.end = IRQ_EB11MP_PMU_CPU2,
.flags = IORESOURCE_IRQ,
},
[3] = {
.start = IRQ_EB11MP_PMU_CPU3,
.end = IRQ_EB11MP_PMU_CPU3,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device pmu_device = {
.id = -1,
.num_resources = ARRAY_SIZE(pmu_resources),
.resource = pmu_resources,
};
static struct resource char_lcd_resources[] = {
{
.start = REALVIEW_CHAR_LCD_BASE,
.end = (REALVIEW_CHAR_LCD_BASE + SZ_4K - 1),
.flags = IORESOURCE_MEM,
},
{
.start = IRQ_EB_CHARLCD,
.end = IRQ_EB_CHARLCD,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device char_lcd_device = {
.name = "arm-charlcd",
.id = -1,
.num_resources = ARRAY_SIZE(char_lcd_resources),
.resource = char_lcd_resources,
};
static void __init gic_init_irq(void)
{
if (core_tile_eb11mp() || core_tile_a9mp()) {
unsigned int pldctrl;
/* new irq mode */
writel(0x0000a05f, __io_address(REALVIEW_SYS_LOCK));
pldctrl = readl(__io_address(REALVIEW_SYS_BASE) + REALVIEW_EB11MP_SYS_PLD_CTRL1);
pldctrl |= 0x00800000;
writel(pldctrl, __io_address(REALVIEW_SYS_BASE) + REALVIEW_EB11MP_SYS_PLD_CTRL1);
writel(0x00000000, __io_address(REALVIEW_SYS_LOCK));
/* core tile GIC, primary */
gic_init(0, 29, __io_address(REALVIEW_EB11MP_GIC_DIST_BASE),
__io_address(REALVIEW_EB11MP_GIC_CPU_BASE));
#ifndef CONFIG_REALVIEW_EB_ARM11MP_REVB
/* board GIC, secondary */
gic_init(1, 96, __io_address(REALVIEW_EB_GIC_DIST_BASE),
__io_address(REALVIEW_EB_GIC_CPU_BASE));
gic_cascade_irq(1, IRQ_EB11MP_EB_IRQ1);
#endif
} else {
/* board GIC, primary */
gic_init(0, 29, __io_address(REALVIEW_EB_GIC_DIST_BASE),
__io_address(REALVIEW_EB_GIC_CPU_BASE));
}
}
/*
* Fix up the IRQ numbers for the RealView EB/ARM11MPCore tile
*/
static void realview_eb11mp_fixup(void)
{
/* AMBA devices */
dmac_device.irq[0] = IRQ_EB11MP_DMA;
uart0_device.irq[0] = IRQ_EB11MP_UART0;
uart1_device.irq[0] = IRQ_EB11MP_UART1;
uart2_device.irq[0] = IRQ_EB11MP_UART2;
uart3_device.irq[0] = IRQ_EB11MP_UART3;
clcd_device.irq[0] = IRQ_EB11MP_CLCD;
wdog_device.irq[0] = IRQ_EB11MP_WDOG;
gpio0_device.irq[0] = IRQ_EB11MP_GPIO0;
gpio1_device.irq[0] = IRQ_EB11MP_GPIO1;
gpio2_device.irq[0] = IRQ_EB11MP_GPIO2;
rtc_device.irq[0] = IRQ_EB11MP_RTC;
sci0_device.irq[0] = IRQ_EB11MP_SCI;
ssp0_device.irq[0] = IRQ_EB11MP_SSP;
aaci_device.irq[0] = IRQ_EB11MP_AACI;
mmc0_device.irq[0] = IRQ_EB11MP_MMCI0A;
mmc0_device.irq[1] = IRQ_EB11MP_MMCI0B;
kmi0_device.irq[0] = IRQ_EB11MP_KMI0;
kmi1_device.irq[0] = IRQ_EB11MP_KMI1;
/* platform devices */
realview_eb_eth_resources[1].start = IRQ_EB11MP_ETH;
realview_eb_eth_resources[1].end = IRQ_EB11MP_ETH;
realview_eb_isp1761_resources[1].start = IRQ_EB11MP_USB;
realview_eb_isp1761_resources[1].end = IRQ_EB11MP_USB;
}
#ifdef CONFIG_HAVE_ARM_TWD
static DEFINE_TWD_LOCAL_TIMER(twd_local_timer,
REALVIEW_EB11MP_TWD_BASE,
IRQ_LOCALTIMER);
static void __init realview_eb_twd_init(void)
{
if (core_tile_eb11mp() || core_tile_a9mp()) {
int err = twd_local_timer_register(&twd_local_timer);
if (err)
pr_err("twd_local_timer_register failed %d\n", err);
}
}
#else
#define realview_eb_twd_init() do { } while(0)
#endif
static void __init realview_eb_timer_init(void)
{
unsigned int timer_irq;
timer0_va_base = __io_address(REALVIEW_EB_TIMER0_1_BASE);
timer1_va_base = __io_address(REALVIEW_EB_TIMER0_1_BASE) + 0x20;
timer2_va_base = __io_address(REALVIEW_EB_TIMER2_3_BASE);
timer3_va_base = __io_address(REALVIEW_EB_TIMER2_3_BASE) + 0x20;
if (core_tile_eb11mp() || core_tile_a9mp())
timer_irq = IRQ_EB11MP_TIMER0_1;
else
timer_irq = IRQ_EB_TIMER0_1;
realview_clk_init(__io_address(REALVIEW_SYS_BASE), false);
realview_timer_init(timer_irq);
realview_eb_twd_init();
}
static void realview_eb_restart(enum reboot_mode mode, const char *cmd)
{
void __iomem *reset_ctrl = __io_address(REALVIEW_SYS_RESETCTL);
void __iomem *lock_ctrl = __io_address(REALVIEW_SYS_LOCK);
/*
* To reset, we hit the on-board reset register
* in the system FPGA
*/
__raw_writel(REALVIEW_SYS_LOCK_VAL, lock_ctrl);
if (core_tile_eb11mp())
__raw_writel(0x0008, reset_ctrl);
dsb();
}
static void __init realview_eb_init(void)
{
int i;
if (core_tile_eb11mp() || core_tile_a9mp()) {
realview_eb11mp_fixup();
#ifdef CONFIG_CACHE_L2X0
/*
* The PL220 needs to be manually configured as the hardware
* doesn't report the correct sizes.
* 1MB (128KB/way), 8-way associativity, event monitor and
* parity enabled, ignore share bit, no force write allocate
* Bits: .... ...0 0111 1001 0000 .... .... ....
*/
l2x0_init(__io_address(REALVIEW_EB11MP_L220_BASE), 0x00790000, 0xfe000fff);
/*
* due to a bug in the l220 cache controller, we must not call
* the sync function. stub it out here instead!
*/
outer_cache.sync = NULL;
#endif
pmu_device.name = core_tile_a9mp() ? "armv7-pmu" : "armv6-pmu";
platform_device_register(&pmu_device);
}
realview_flash_register(&realview_eb_flash_resource, 1);
platform_device_register(&realview_i2c_device);
platform_device_register(&char_lcd_device);
platform_device_register(&realview_leds_device);
eth_device_register();
realview_usb_register(realview_eb_isp1761_resources);
for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
struct amba_device *d = amba_devs[i];
amba_device_register(d, &iomem_resource);
}
}
MACHINE_START(REALVIEW_EB, "ARM-RealView EB")
/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
.atag_offset = 0x100,
.smp = smp_ops(realview_smp_ops),
.fixup = realview_fixup,
.map_io = realview_eb_map_io,
.init_early = realview_init_early,
.init_irq = gic_init_irq,
.init_time = realview_eb_timer_init,
.init_machine = realview_eb_init,
#ifdef CONFIG_ZONE_DMA
.dma_zone_size = SZ_256M,
#endif
.restart = realview_eb_restart,
MACHINE_END
/*
* linux/arch/arm/mach-realview/realview_pb1176.c
*
* Copyright (C) 2008 ARM Limited
* Copyright (C) 2000 Deep Blue Solutions Ltd
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/device.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl061.h>
#include <linux/amba/mmci.h>
#include <linux/amba/pl022.h>
#include <linux/mtd/physmap.h>
#include <linux/mtd/partitions.h>
#include <linux/io.h>
#include <linux/irqchip/arm-gic.h>
#include <linux/platform_data/clk-realview.h>
#include <linux/reboot.h>
#include <linux/memblock.h>
#include "hardware.h"
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/pgtable.h>
#include <asm/hardware/cache-l2x0.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
#include <asm/mach/time.h>
#include "board-pb1176.h"
#include "irqs-pb1176.h"
#include "core.h"
static struct map_desc realview_pb1176_io_desc[] __initdata = {
{
.virtual = IO_ADDRESS(REALVIEW_SYS_BASE),
.pfn = __phys_to_pfn(REALVIEW_SYS_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_PB1176_GIC_CPU_BASE),
.pfn = __phys_to_pfn(REALVIEW_PB1176_GIC_CPU_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_PB1176_GIC_DIST_BASE),
.pfn = __phys_to_pfn(REALVIEW_PB1176_GIC_DIST_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_DC1176_GIC_CPU_BASE),
.pfn = __phys_to_pfn(REALVIEW_DC1176_GIC_CPU_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_DC1176_GIC_DIST_BASE),
.pfn = __phys_to_pfn(REALVIEW_DC1176_GIC_DIST_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_SCTL_BASE),
.pfn = __phys_to_pfn(REALVIEW_SCTL_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_PB1176_TIMER0_1_BASE),
.pfn = __phys_to_pfn(REALVIEW_PB1176_TIMER0_1_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_PB1176_TIMER2_3_BASE),
.pfn = __phys_to_pfn(REALVIEW_PB1176_TIMER2_3_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_PB1176_L220_BASE),
.pfn = __phys_to_pfn(REALVIEW_PB1176_L220_BASE),
.length = SZ_8K,
.type = MT_DEVICE,
},
#ifdef CONFIG_DEBUG_LL
{
.virtual = IO_ADDRESS(REALVIEW_PB1176_UART0_BASE),
.pfn = __phys_to_pfn(REALVIEW_PB1176_UART0_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
},
#endif
};
static void __init realview_pb1176_map_io(void)
{
iotable_init(realview_pb1176_io_desc, ARRAY_SIZE(realview_pb1176_io_desc));
}
static struct pl061_platform_data gpio0_plat_data = {
.gpio_base = 0,
};
static struct pl061_platform_data gpio1_plat_data = {
.gpio_base = 8,
};
static struct pl061_platform_data gpio2_plat_data = {
.gpio_base = 16,
};
static struct pl022_ssp_controller ssp0_plat_data = {
.bus_id = 0,
.enable_dma = 0,
.num_chipselect = 1,
};
/*
* RealView PB1176 AMBA devices
*/
#define GPIO2_IRQ { IRQ_PB1176_GPIO2 }
#define GPIO3_IRQ { IRQ_PB1176_GPIO3 }
#define AACI_IRQ { IRQ_PB1176_AACI }
#define MMCI0_IRQ { IRQ_PB1176_MMCI0A, IRQ_PB1176_MMCI0B }
#define KMI0_IRQ { IRQ_PB1176_KMI0 }
#define KMI1_IRQ { IRQ_PB1176_KMI1 }
#define PB1176_SMC_IRQ { }
#define MPMC_IRQ { }
#define PB1176_CLCD_IRQ { IRQ_DC1176_CLCD }
#define SCTL_IRQ { }
#define PB1176_WATCHDOG_IRQ { IRQ_DC1176_WATCHDOG }
#define PB1176_GPIO0_IRQ { IRQ_DC1176_GPIO0 }
#define GPIO1_IRQ { IRQ_PB1176_GPIO1 }
#define PB1176_RTC_IRQ { IRQ_DC1176_RTC }
#define SCI_IRQ { IRQ_PB1176_SCI }
#define PB1176_UART0_IRQ { IRQ_DC1176_UART0 }
#define PB1176_UART1_IRQ { IRQ_DC1176_UART1 }
#define PB1176_UART2_IRQ { IRQ_DC1176_UART2 }
#define PB1176_UART3_IRQ { IRQ_DC1176_UART3 }
#define PB1176_UART4_IRQ { IRQ_PB1176_UART4 }
#define PB1176_SSP_IRQ { IRQ_DC1176_SSP }
/* FPGA Primecells */
APB_DEVICE(aaci, "fpga:aaci", AACI, NULL);
APB_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
APB_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
APB_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
APB_DEVICE(uart4, "fpga:uart4", PB1176_UART4, NULL);
/* DevChip Primecells */
AHB_DEVICE(smc, "dev:smc", PB1176_SMC, NULL);
AHB_DEVICE(sctl, "dev:sctl", SCTL, NULL);
APB_DEVICE(wdog, "dev:wdog", PB1176_WATCHDOG, NULL);
APB_DEVICE(gpio0, "dev:gpio0", PB1176_GPIO0, &gpio0_plat_data);
APB_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
APB_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
APB_DEVICE(rtc, "dev:rtc", PB1176_RTC, NULL);
APB_DEVICE(sci0, "dev:sci0", SCI, NULL);
APB_DEVICE(uart0, "dev:uart0", PB1176_UART0, NULL);
APB_DEVICE(uart1, "dev:uart1", PB1176_UART1, NULL);
APB_DEVICE(uart2, "dev:uart2", PB1176_UART2, NULL);
APB_DEVICE(uart3, "dev:uart3", PB1176_UART3, NULL);
APB_DEVICE(ssp0, "dev:ssp0", PB1176_SSP, &ssp0_plat_data);
AHB_DEVICE(clcd, "dev:clcd", PB1176_CLCD, &clcd_plat_data);
static struct amba_device *amba_devs[] __initdata = {
&uart0_device,
&uart1_device,
&uart2_device,
&uart3_device,
&uart4_device,
&smc_device,
&clcd_device,
&sctl_device,
&wdog_device,
&gpio0_device,
&gpio1_device,
&gpio2_device,
&rtc_device,
&sci0_device,
&ssp0_device,
&aaci_device,
&mmc0_device,
&kmi0_device,
&kmi1_device,
};
/*
* RealView PB1176 platform devices
*/
static struct resource realview_pb1176_flash_resources[] = {
{
.start = REALVIEW_PB1176_FLASH_BASE,
.end = REALVIEW_PB1176_FLASH_BASE + REALVIEW_PB1176_FLASH_SIZE - 1,
.flags = IORESOURCE_MEM,
},
#ifdef CONFIG_REALVIEW_PB1176_SECURE_FLASH
{
.start = REALVIEW_PB1176_SEC_FLASH_BASE,
.end = REALVIEW_PB1176_SEC_FLASH_BASE + REALVIEW_PB1176_SEC_FLASH_SIZE - 1,
.flags = IORESOURCE_MEM,
},
#endif
};
static struct physmap_flash_data pb1176_rom_pdata = {
.probe_type = "map_rom",
.width = 4,
.nr_parts = 0,
};
static struct resource pb1176_rom_resources[] = {
/*
* This exposes the PB1176 DevChip ROM as an MTD ROM mapping.
* The reference manual states that this is actually a pseudo-ROM
* programmed in NVRAM.
*/
{
.start = REALVIEW_DC1176_ROM_BASE,
.end = REALVIEW_DC1176_ROM_BASE + SZ_16K - 1,
.flags = IORESOURCE_MEM,
}
};
static struct platform_device pb1176_rom_device = {
.name = "physmap-flash",
.id = -1,
.num_resources = ARRAY_SIZE(pb1176_rom_resources),
.resource = pb1176_rom_resources,
.dev = {
.platform_data = &pb1176_rom_pdata,
},
};
static struct resource realview_pb1176_smsc911x_resources[] = {
[0] = {
.start = REALVIEW_PB1176_ETH_BASE,
.end = REALVIEW_PB1176_ETH_BASE + SZ_64K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = IRQ_PB1176_ETH,
.end = IRQ_PB1176_ETH,
.flags = IORESOURCE_IRQ,
},
};
static struct resource realview_pb1176_isp1761_resources[] = {
[0] = {
.start = REALVIEW_PB1176_USB_BASE,
.end = REALVIEW_PB1176_USB_BASE + SZ_128K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = IRQ_PB1176_USB,
.end = IRQ_PB1176_USB,
.flags = IORESOURCE_IRQ,
},
};
static struct resource pmu_resource = {
.start = IRQ_DC1176_CORE_PMU,
.end = IRQ_DC1176_CORE_PMU,
.flags = IORESOURCE_IRQ,
};
static struct platform_device pmu_device = {
.name = "armv6-pmu",
.id = -1,
.num_resources = 1,
.resource = &pmu_resource,
};
static struct resource char_lcd_resources[] = {
{
.start = REALVIEW_CHAR_LCD_BASE,
.end = (REALVIEW_CHAR_LCD_BASE + SZ_4K - 1),
.flags = IORESOURCE_MEM,
},
{
.start = IRQ_PB1176_CHARLCD,
.end = IRQ_PB1176_CHARLCD,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device char_lcd_device = {
.name = "arm-charlcd",
.id = -1,
.num_resources = ARRAY_SIZE(char_lcd_resources),
.resource = char_lcd_resources,
};
static void __init gic_init_irq(void)
{
/* ARM1176 DevChip GIC, primary */
gic_init(0, IRQ_DC1176_GIC_START,
__io_address(REALVIEW_DC1176_GIC_DIST_BASE),
__io_address(REALVIEW_DC1176_GIC_CPU_BASE));
/* board GIC, secondary */
gic_init(1, IRQ_PB1176_GIC_START,
__io_address(REALVIEW_PB1176_GIC_DIST_BASE),
__io_address(REALVIEW_PB1176_GIC_CPU_BASE));
gic_cascade_irq(1, IRQ_DC1176_PB_IRQ1);
}
static void __init realview_pb1176_timer_init(void)
{
timer0_va_base = __io_address(REALVIEW_PB1176_TIMER0_1_BASE);
timer1_va_base = __io_address(REALVIEW_PB1176_TIMER0_1_BASE) + 0x20;
timer2_va_base = __io_address(REALVIEW_PB1176_TIMER2_3_BASE);
timer3_va_base = __io_address(REALVIEW_PB1176_TIMER2_3_BASE) + 0x20;
realview_clk_init(__io_address(REALVIEW_SYS_BASE), true);
realview_timer_init(IRQ_DC1176_TIMER0);
}
static void realview_pb1176_restart(enum reboot_mode mode, const char *cmd)
{
void __iomem *reset_ctrl = __io_address(REALVIEW_SYS_RESETCTL);
void __iomem *lock_ctrl = __io_address(REALVIEW_SYS_LOCK);
__raw_writel(REALVIEW_SYS_LOCK_VAL, lock_ctrl);
__raw_writel(REALVIEW_PB1176_SYS_SOFT_RESET, reset_ctrl);
dsb();
}
static void realview_pb1176_fixup(struct tag *tags, char **from)
{
/*
* RealView PB1176 only has 128MB of RAM mapped at 0.
*/
memblock_add(0, SZ_128M);
}
static void __init realview_pb1176_init(void)
{
int i;
#ifdef CONFIG_CACHE_L2X0
/*
* The PL220 needs to be manually configured as the hardware
* doesn't report the correct sizes.
* 128kB (16kB/way), 8-way associativity, event monitor and
* parity enabled, ignore share bit, no force write allocate
* Bits: .... ...0 0111 0011 0000 .... .... ....
*/
l2x0_init(__io_address(REALVIEW_PB1176_L220_BASE), 0x00730000, 0xfe000fff);
#endif
realview_flash_register(realview_pb1176_flash_resources,
ARRAY_SIZE(realview_pb1176_flash_resources));
platform_device_register(&pb1176_rom_device);
realview_eth_register(NULL, realview_pb1176_smsc911x_resources);
platform_device_register(&realview_i2c_device);
realview_usb_register(realview_pb1176_isp1761_resources);
platform_device_register(&pmu_device);
platform_device_register(&char_lcd_device);
platform_device_register(&realview_leds_device);
for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
struct amba_device *d = amba_devs[i];
amba_device_register(d, &iomem_resource);
}
}
MACHINE_START(REALVIEW_PB1176, "ARM-RealView PB1176")
/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
.atag_offset = 0x100,
.fixup = realview_pb1176_fixup,
.map_io = realview_pb1176_map_io,
.init_early = realview_init_early,
.init_irq = gic_init_irq,
.init_time = realview_pb1176_timer_init,
.init_machine = realview_pb1176_init,
#ifdef CONFIG_ZONE_DMA
.dma_zone_size = SZ_256M,
#endif
.restart = realview_pb1176_restart,
MACHINE_END
/*
* linux/arch/arm/mach-realview/realview_pb11mp.c
*
* Copyright (C) 2008 ARM Limited
* Copyright (C) 2000 Deep Blue Solutions Ltd
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/device.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl061.h>
#include <linux/amba/mmci.h>
#include <linux/amba/pl022.h>
#include <linux/io.h>
#include <linux/irqchip/arm-gic.h>
#include <linux/platform_data/clk-realview.h>
#include <linux/reboot.h>
#include "hardware.h"
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/pgtable.h>
#include <asm/hardware/cache-l2x0.h>
#include <asm/smp_twd.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
#include <asm/mach/time.h>
#include <asm/outercache.h>
#include "board-pb11mp.h"
#include "irqs-pb11mp.h"
#include "core.h"
static struct map_desc realview_pb11mp_io_desc[] __initdata = {
{
.virtual = IO_ADDRESS(REALVIEW_SYS_BASE),
.pfn = __phys_to_pfn(REALVIEW_SYS_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_PB11MP_GIC_CPU_BASE),
.pfn = __phys_to_pfn(REALVIEW_PB11MP_GIC_CPU_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_PB11MP_GIC_DIST_BASE),
.pfn = __phys_to_pfn(REALVIEW_PB11MP_GIC_DIST_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, { /* Maps the SCU, GIC CPU interface, TWD, GIC DIST */
.virtual = IO_ADDRESS(REALVIEW_TC11MP_PRIV_MEM_BASE),
.pfn = __phys_to_pfn(REALVIEW_TC11MP_PRIV_MEM_BASE),
.length = REALVIEW_TC11MP_PRIV_MEM_SIZE,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_SCTL_BASE),
.pfn = __phys_to_pfn(REALVIEW_SCTL_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_PB11MP_TIMER0_1_BASE),
.pfn = __phys_to_pfn(REALVIEW_PB11MP_TIMER0_1_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_PB11MP_TIMER2_3_BASE),
.pfn = __phys_to_pfn(REALVIEW_PB11MP_TIMER2_3_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_TC11MP_L220_BASE),
.pfn = __phys_to_pfn(REALVIEW_TC11MP_L220_BASE),
.length = SZ_8K,
.type = MT_DEVICE,
},
#ifdef CONFIG_DEBUG_LL
{
.virtual = IO_ADDRESS(REALVIEW_PB11MP_UART0_BASE),
.pfn = __phys_to_pfn(REALVIEW_PB11MP_UART0_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
},
#endif
};
static void __init realview_pb11mp_map_io(void)
{
iotable_init(realview_pb11mp_io_desc, ARRAY_SIZE(realview_pb11mp_io_desc));
}
static struct pl061_platform_data gpio0_plat_data = {
.gpio_base = 0,
};
static struct pl061_platform_data gpio1_plat_data = {
.gpio_base = 8,
};
static struct pl061_platform_data gpio2_plat_data = {
.gpio_base = 16,
};
static struct pl022_ssp_controller ssp0_plat_data = {
.bus_id = 0,
.enable_dma = 0,
.num_chipselect = 1,
};
/*
* RealView PB11MPCore AMBA devices
*/
#define GPIO2_IRQ { IRQ_PB11MP_GPIO2 }
#define GPIO3_IRQ { IRQ_PB11MP_GPIO3 }
#define AACI_IRQ { IRQ_TC11MP_AACI }
#define MMCI0_IRQ { IRQ_TC11MP_MMCI0A, IRQ_TC11MP_MMCI0B }
#define KMI0_IRQ { IRQ_TC11MP_KMI0 }
#define KMI1_IRQ { IRQ_TC11MP_KMI1 }
#define PB11MP_SMC_IRQ { }
#define MPMC_IRQ { }
#define PB11MP_CLCD_IRQ { IRQ_PB11MP_CLCD }
#define DMAC_IRQ { IRQ_PB11MP_DMAC }
#define SCTL_IRQ { }
#define PB11MP_WATCHDOG_IRQ { IRQ_PB11MP_WATCHDOG }
#define PB11MP_GPIO0_IRQ { IRQ_PB11MP_GPIO0 }
#define GPIO1_IRQ { IRQ_PB11MP_GPIO1 }
#define PB11MP_RTC_IRQ { IRQ_TC11MP_RTC }
#define SCI_IRQ { IRQ_PB11MP_SCI }
#define PB11MP_UART0_IRQ { IRQ_TC11MP_UART0 }
#define PB11MP_UART1_IRQ { IRQ_TC11MP_UART1 }
#define PB11MP_UART2_IRQ { IRQ_PB11MP_UART2 }
#define PB11MP_UART3_IRQ { IRQ_PB11MP_UART3 }
#define PB11MP_SSP_IRQ { IRQ_PB11MP_SSP }
/* FPGA Primecells */
APB_DEVICE(aaci, "fpga:aaci", AACI, NULL);
APB_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
APB_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
APB_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
APB_DEVICE(uart3, "fpga:uart3", PB11MP_UART3, NULL);
/* DevChip Primecells */
AHB_DEVICE(smc, "dev:smc", PB11MP_SMC, NULL);
AHB_DEVICE(sctl, "dev:sctl", SCTL, NULL);
APB_DEVICE(wdog, "dev:wdog", PB11MP_WATCHDOG, NULL);
APB_DEVICE(gpio0, "dev:gpio0", PB11MP_GPIO0, &gpio0_plat_data);
APB_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
APB_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
APB_DEVICE(rtc, "dev:rtc", PB11MP_RTC, NULL);
APB_DEVICE(sci0, "dev:sci0", SCI, NULL);
APB_DEVICE(uart0, "dev:uart0", PB11MP_UART0, NULL);
APB_DEVICE(uart1, "dev:uart1", PB11MP_UART1, NULL);
APB_DEVICE(uart2, "dev:uart2", PB11MP_UART2, NULL);
APB_DEVICE(ssp0, "dev:ssp0", PB11MP_SSP, &ssp0_plat_data);
/* Primecells on the NEC ISSP chip */
AHB_DEVICE(clcd, "issp:clcd", PB11MP_CLCD, &clcd_plat_data);
AHB_DEVICE(dmac, "issp:dmac", DMAC, NULL);
static struct amba_device *amba_devs[] __initdata = {
&dmac_device,
&uart0_device,
&uart1_device,
&uart2_device,
&uart3_device,
&smc_device,
&clcd_device,
&sctl_device,
&wdog_device,
&gpio0_device,
&gpio1_device,
&gpio2_device,
&rtc_device,
&sci0_device,
&ssp0_device,
&aaci_device,
&mmc0_device,
&kmi0_device,
&kmi1_device,
};
/*
* RealView PB11MPCore platform devices
*/
static struct resource realview_pb11mp_flash_resource[] = {
[0] = {
.start = REALVIEW_PB11MP_FLASH0_BASE,
.end = REALVIEW_PB11MP_FLASH0_BASE + REALVIEW_PB11MP_FLASH0_SIZE - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = REALVIEW_PB11MP_FLASH1_BASE,
.end = REALVIEW_PB11MP_FLASH1_BASE + REALVIEW_PB11MP_FLASH1_SIZE - 1,
.flags = IORESOURCE_MEM,
},
};
static struct resource realview_pb11mp_smsc911x_resources[] = {
[0] = {
.start = REALVIEW_PB11MP_ETH_BASE,
.end = REALVIEW_PB11MP_ETH_BASE + SZ_64K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = IRQ_TC11MP_ETH,
.end = IRQ_TC11MP_ETH,
.flags = IORESOURCE_IRQ,
},
};
static struct resource realview_pb11mp_isp1761_resources[] = {
[0] = {
.start = REALVIEW_PB11MP_USB_BASE,
.end = REALVIEW_PB11MP_USB_BASE + SZ_128K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = IRQ_TC11MP_USB,
.end = IRQ_TC11MP_USB,
.flags = IORESOURCE_IRQ,
},
};
static struct resource pmu_resources[] = {
[0] = {
.start = IRQ_TC11MP_PMU_CPU0,
.end = IRQ_TC11MP_PMU_CPU0,
.flags = IORESOURCE_IRQ,
},
[1] = {
.start = IRQ_TC11MP_PMU_CPU1,
.end = IRQ_TC11MP_PMU_CPU1,
.flags = IORESOURCE_IRQ,
},
[2] = {
.start = IRQ_TC11MP_PMU_CPU2,
.end = IRQ_TC11MP_PMU_CPU2,
.flags = IORESOURCE_IRQ,
},
[3] = {
.start = IRQ_TC11MP_PMU_CPU3,
.end = IRQ_TC11MP_PMU_CPU3,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device pmu_device = {
.name = "armv6-pmu",
.id = -1,
.num_resources = ARRAY_SIZE(pmu_resources),
.resource = pmu_resources,
};
static void __init gic_init_irq(void)
{
unsigned int pldctrl;
/* new irq mode with no DCC */
writel(0x0000a05f, __io_address(REALVIEW_SYS_LOCK));
pldctrl = readl(__io_address(REALVIEW_SYS_BASE) + REALVIEW_PB11MP_SYS_PLD_CTRL1);
pldctrl |= 2 << 22;
writel(pldctrl, __io_address(REALVIEW_SYS_BASE) + REALVIEW_PB11MP_SYS_PLD_CTRL1);
writel(0x00000000, __io_address(REALVIEW_SYS_LOCK));
/* ARM11MPCore test chip GIC, primary */
gic_init(0, 29, __io_address(REALVIEW_TC11MP_GIC_DIST_BASE),
__io_address(REALVIEW_TC11MP_GIC_CPU_BASE));
/* board GIC, secondary */
gic_init(1, IRQ_PB11MP_GIC_START,
__io_address(REALVIEW_PB11MP_GIC_DIST_BASE),
__io_address(REALVIEW_PB11MP_GIC_CPU_BASE));
gic_cascade_irq(1, IRQ_TC11MP_PB_IRQ1);
}
#ifdef CONFIG_HAVE_ARM_TWD
static DEFINE_TWD_LOCAL_TIMER(twd_local_timer,
REALVIEW_TC11MP_TWD_BASE,
IRQ_LOCALTIMER);
static void __init realview_pb11mp_twd_init(void)
{
int err = twd_local_timer_register(&twd_local_timer);
if (err)
pr_err("twd_local_timer_register failed %d\n", err);
}
#else
#define realview_pb11mp_twd_init() do {} while(0)
#endif
static void __init realview_pb11mp_timer_init(void)
{
timer0_va_base = __io_address(REALVIEW_PB11MP_TIMER0_1_BASE);
timer1_va_base = __io_address(REALVIEW_PB11MP_TIMER0_1_BASE) + 0x20;
timer2_va_base = __io_address(REALVIEW_PB11MP_TIMER2_3_BASE);
timer3_va_base = __io_address(REALVIEW_PB11MP_TIMER2_3_BASE) + 0x20;
realview_clk_init(__io_address(REALVIEW_SYS_BASE), false);
realview_timer_init(IRQ_TC11MP_TIMER0_1);
realview_pb11mp_twd_init();
}
static void realview_pb11mp_restart(enum reboot_mode mode, const char *cmd)
{
void __iomem *reset_ctrl = __io_address(REALVIEW_SYS_RESETCTL);
void __iomem *lock_ctrl = __io_address(REALVIEW_SYS_LOCK);
/*
* To reset, we hit the on-board reset register
* in the system FPGA
*/
__raw_writel(REALVIEW_SYS_LOCK_VAL, lock_ctrl);
__raw_writel(0x0000, reset_ctrl);
__raw_writel(0x0004, reset_ctrl);
dsb();
}
static void __init realview_pb11mp_init(void)
{
int i;
#ifdef CONFIG_CACHE_L2X0
/*
* The PL220 needs to be manually configured as the hardware
* doesn't report the correct sizes.
* 1MB (128KB/way), 8-way associativity, event monitor and
* parity enabled, ignore share bit, no force write allocate
* Bits: .... ...0 0111 1001 0000 .... .... ....
*/
l2x0_init(__io_address(REALVIEW_TC11MP_L220_BASE), 0x00790000, 0xfe000fff);
/*
* due to a bug in the l220 cache controller, we must not call
* the sync function. stub it out here instead!
*/
outer_cache.sync = NULL;
#endif
realview_flash_register(realview_pb11mp_flash_resource,
ARRAY_SIZE(realview_pb11mp_flash_resource));
realview_eth_register(NULL, realview_pb11mp_smsc911x_resources);
platform_device_register(&realview_i2c_device);
platform_device_register(&realview_cf_device);
platform_device_register(&realview_leds_device);
realview_usb_register(realview_pb11mp_isp1761_resources);
platform_device_register(&pmu_device);
for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
struct amba_device *d = amba_devs[i];
amba_device_register(d, &iomem_resource);
}
}
MACHINE_START(REALVIEW_PB11MP, "ARM-RealView PB11MPCore")
/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
.atag_offset = 0x100,
.smp = smp_ops(realview_smp_ops),
.fixup = realview_fixup,
.map_io = realview_pb11mp_map_io,
.init_early = realview_init_early,
.init_irq = gic_init_irq,
.init_time = realview_pb11mp_timer_init,
.init_machine = realview_pb11mp_init,
#ifdef CONFIG_ZONE_DMA
.dma_zone_size = SZ_256M,
#endif
.restart = realview_pb11mp_restart,
MACHINE_END
/*
* linux/arch/arm/mach-realview/realview_pba8.c
*
* Copyright (C) 2008 ARM Limited
* Copyright (C) 2000 Deep Blue Solutions Ltd
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/device.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl061.h>
#include <linux/amba/mmci.h>
#include <linux/amba/pl022.h>
#include <linux/io.h>
#include <linux/irqchip/arm-gic.h>
#include <linux/platform_data/clk-realview.h>
#include <linux/reboot.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/pgtable.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/time.h>
#include "hardware.h"
#include "board-pba8.h"
#include "irqs-pba8.h"
#include "core.h"
static struct map_desc realview_pba8_io_desc[] __initdata = {
{
.virtual = IO_ADDRESS(REALVIEW_SYS_BASE),
.pfn = __phys_to_pfn(REALVIEW_SYS_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_PBA8_GIC_CPU_BASE),
.pfn = __phys_to_pfn(REALVIEW_PBA8_GIC_CPU_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_PBA8_GIC_DIST_BASE),
.pfn = __phys_to_pfn(REALVIEW_PBA8_GIC_DIST_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_SCTL_BASE),
.pfn = __phys_to_pfn(REALVIEW_SCTL_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_PBA8_TIMER0_1_BASE),
.pfn = __phys_to_pfn(REALVIEW_PBA8_TIMER0_1_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_PBA8_TIMER2_3_BASE),
.pfn = __phys_to_pfn(REALVIEW_PBA8_TIMER2_3_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
},
#ifdef CONFIG_DEBUG_LL
{
.virtual = IO_ADDRESS(REALVIEW_PBA8_UART0_BASE),
.pfn = __phys_to_pfn(REALVIEW_PBA8_UART0_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
},
#endif
};
static void __init realview_pba8_map_io(void)
{
iotable_init(realview_pba8_io_desc, ARRAY_SIZE(realview_pba8_io_desc));
}
static struct pl061_platform_data gpio0_plat_data = {
.gpio_base = 0,
};
static struct pl061_platform_data gpio1_plat_data = {
.gpio_base = 8,
};
static struct pl061_platform_data gpio2_plat_data = {
.gpio_base = 16,
};
static struct pl022_ssp_controller ssp0_plat_data = {
.bus_id = 0,
.enable_dma = 0,
.num_chipselect = 1,
};
/*
* RealView PBA8Core AMBA devices
*/
#define GPIO2_IRQ { IRQ_PBA8_GPIO2 }
#define GPIO3_IRQ { IRQ_PBA8_GPIO3 }
#define AACI_IRQ { IRQ_PBA8_AACI }
#define MMCI0_IRQ { IRQ_PBA8_MMCI0A, IRQ_PBA8_MMCI0B }
#define KMI0_IRQ { IRQ_PBA8_KMI0 }
#define KMI1_IRQ { IRQ_PBA8_KMI1 }
#define PBA8_SMC_IRQ { }
#define MPMC_IRQ { }
#define PBA8_CLCD_IRQ { IRQ_PBA8_CLCD }
#define DMAC_IRQ { IRQ_PBA8_DMAC }
#define SCTL_IRQ { }
#define PBA8_WATCHDOG_IRQ { IRQ_PBA8_WATCHDOG }
#define PBA8_GPIO0_IRQ { IRQ_PBA8_GPIO0 }
#define GPIO1_IRQ { IRQ_PBA8_GPIO1 }
#define PBA8_RTC_IRQ { IRQ_PBA8_RTC }
#define SCI_IRQ { IRQ_PBA8_SCI }
#define PBA8_UART0_IRQ { IRQ_PBA8_UART0 }
#define PBA8_UART1_IRQ { IRQ_PBA8_UART1 }
#define PBA8_UART2_IRQ { IRQ_PBA8_UART2 }
#define PBA8_UART3_IRQ { IRQ_PBA8_UART3 }
#define PBA8_SSP_IRQ { IRQ_PBA8_SSP }
/* FPGA Primecells */
APB_DEVICE(aaci, "fpga:aaci", AACI, NULL);
APB_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
APB_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
APB_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
APB_DEVICE(uart3, "fpga:uart3", PBA8_UART3, NULL);
/* DevChip Primecells */
AHB_DEVICE(smc, "dev:smc", PBA8_SMC, NULL);
AHB_DEVICE(sctl, "dev:sctl", SCTL, NULL);
APB_DEVICE(wdog, "dev:wdog", PBA8_WATCHDOG, NULL);
APB_DEVICE(gpio0, "dev:gpio0", PBA8_GPIO0, &gpio0_plat_data);
APB_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
APB_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
APB_DEVICE(rtc, "dev:rtc", PBA8_RTC, NULL);
APB_DEVICE(sci0, "dev:sci0", SCI, NULL);
APB_DEVICE(uart0, "dev:uart0", PBA8_UART0, NULL);
APB_DEVICE(uart1, "dev:uart1", PBA8_UART1, NULL);
APB_DEVICE(uart2, "dev:uart2", PBA8_UART2, NULL);
APB_DEVICE(ssp0, "dev:ssp0", PBA8_SSP, &ssp0_plat_data);
/* Primecells on the NEC ISSP chip */
AHB_DEVICE(clcd, "issp:clcd", PBA8_CLCD, &clcd_plat_data);
AHB_DEVICE(dmac, "issp:dmac", DMAC, NULL);
static struct amba_device *amba_devs[] __initdata = {
&dmac_device,
&uart0_device,
&uart1_device,
&uart2_device,
&uart3_device,
&smc_device,
&clcd_device,
&sctl_device,
&wdog_device,
&gpio0_device,
&gpio1_device,
&gpio2_device,
&rtc_device,
&sci0_device,
&ssp0_device,
&aaci_device,
&mmc0_device,
&kmi0_device,
&kmi1_device,
};
/*
* RealView PB-A8 platform devices
*/
static struct resource realview_pba8_flash_resource[] = {
[0] = {
.start = REALVIEW_PBA8_FLASH0_BASE,
.end = REALVIEW_PBA8_FLASH0_BASE + REALVIEW_PBA8_FLASH0_SIZE - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = REALVIEW_PBA8_FLASH1_BASE,
.end = REALVIEW_PBA8_FLASH1_BASE + REALVIEW_PBA8_FLASH1_SIZE - 1,
.flags = IORESOURCE_MEM,
},
};
static struct resource realview_pba8_smsc911x_resources[] = {
[0] = {
.start = REALVIEW_PBA8_ETH_BASE,
.end = REALVIEW_PBA8_ETH_BASE + SZ_64K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = IRQ_PBA8_ETH,
.end = IRQ_PBA8_ETH,
.flags = IORESOURCE_IRQ,
},
};
static struct resource realview_pba8_isp1761_resources[] = {
[0] = {
.start = REALVIEW_PBA8_USB_BASE,
.end = REALVIEW_PBA8_USB_BASE + SZ_128K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = IRQ_PBA8_USB,
.end = IRQ_PBA8_USB,
.flags = IORESOURCE_IRQ,
},
};
static struct resource pmu_resource = {
.start = IRQ_PBA8_PMU,
.end = IRQ_PBA8_PMU,
.flags = IORESOURCE_IRQ,
};
static struct platform_device pmu_device = {
.name = "armv7-pmu",
.id = -1,
.num_resources = 1,
.resource = &pmu_resource,
};
static void __init gic_init_irq(void)
{
/* ARM PB-A8 on-board GIC */
gic_init(0, IRQ_PBA8_GIC_START,
__io_address(REALVIEW_PBA8_GIC_DIST_BASE),
__io_address(REALVIEW_PBA8_GIC_CPU_BASE));
}
static void __init realview_pba8_timer_init(void)
{
timer0_va_base = __io_address(REALVIEW_PBA8_TIMER0_1_BASE);
timer1_va_base = __io_address(REALVIEW_PBA8_TIMER0_1_BASE) + 0x20;
timer2_va_base = __io_address(REALVIEW_PBA8_TIMER2_3_BASE);
timer3_va_base = __io_address(REALVIEW_PBA8_TIMER2_3_BASE) + 0x20;
realview_clk_init(__io_address(REALVIEW_SYS_BASE), false);
realview_timer_init(IRQ_PBA8_TIMER0_1);
}
static void realview_pba8_restart(enum reboot_mode mode, const char *cmd)
{
void __iomem *reset_ctrl = __io_address(REALVIEW_SYS_RESETCTL);
void __iomem *lock_ctrl = __io_address(REALVIEW_SYS_LOCK);
/*
* To reset, we hit the on-board reset register
* in the system FPGA
*/
__raw_writel(REALVIEW_SYS_LOCK_VAL, lock_ctrl);
__raw_writel(0x0000, reset_ctrl);
__raw_writel(0x0004, reset_ctrl);
dsb();
}
static void __init realview_pba8_init(void)
{
int i;
realview_flash_register(realview_pba8_flash_resource,
ARRAY_SIZE(realview_pba8_flash_resource));
realview_eth_register(NULL, realview_pba8_smsc911x_resources);
platform_device_register(&realview_i2c_device);
platform_device_register(&realview_cf_device);
platform_device_register(&realview_leds_device);
realview_usb_register(realview_pba8_isp1761_resources);
platform_device_register(&pmu_device);
for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
struct amba_device *d = amba_devs[i];
amba_device_register(d, &iomem_resource);
}
}
MACHINE_START(REALVIEW_PBA8, "ARM-RealView PB-A8")
/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
.atag_offset = 0x100,
.fixup = realview_fixup,
.map_io = realview_pba8_map_io,
.init_early = realview_init_early,
.init_irq = gic_init_irq,
.init_time = realview_pba8_timer_init,
.init_machine = realview_pba8_init,
#ifdef CONFIG_ZONE_DMA
.dma_zone_size = SZ_256M,
#endif
.restart = realview_pba8_restart,
MACHINE_END
/*
* arch/arm/mach-realview/realview_pbx.c
*
* Copyright (C) 2009 ARM Limited
* Copyright (C) 2000 Deep Blue Solutions Ltd
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/device.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl061.h>
#include <linux/amba/mmci.h>
#include <linux/amba/pl022.h>
#include <linux/io.h>
#include <linux/irqchip/arm-gic.h>
#include <linux/platform_data/clk-realview.h>
#include <linux/reboot.h>
#include <linux/memblock.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/smp_twd.h>
#include <asm/pgtable.h>
#include <asm/hardware/cache-l2x0.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/time.h>
#include "hardware.h"
#include "board-pbx.h"
#include "irqs-pbx.h"
#include "core.h"
static struct map_desc realview_pbx_io_desc[] __initdata = {
{
.virtual = IO_ADDRESS(REALVIEW_SYS_BASE),
.pfn = __phys_to_pfn(REALVIEW_SYS_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_PBX_GIC_CPU_BASE),
.pfn = __phys_to_pfn(REALVIEW_PBX_GIC_CPU_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_PBX_GIC_DIST_BASE),
.pfn = __phys_to_pfn(REALVIEW_PBX_GIC_DIST_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_SCTL_BASE),
.pfn = __phys_to_pfn(REALVIEW_SCTL_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_PBX_TIMER0_1_BASE),
.pfn = __phys_to_pfn(REALVIEW_PBX_TIMER0_1_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_PBX_TIMER2_3_BASE),
.pfn = __phys_to_pfn(REALVIEW_PBX_TIMER2_3_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
},
#ifdef CONFIG_DEBUG_LL
{
.virtual = IO_ADDRESS(REALVIEW_PBX_UART0_BASE),
.pfn = __phys_to_pfn(REALVIEW_PBX_UART0_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
},
#endif
};
static struct map_desc realview_local_io_desc[] __initdata = {
{
.virtual = IO_ADDRESS(REALVIEW_PBX_TILE_SCU_BASE),
.pfn = __phys_to_pfn(REALVIEW_PBX_TILE_SCU_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_PBX_TILE_GIC_DIST_BASE),
.pfn = __phys_to_pfn(REALVIEW_PBX_TILE_GIC_DIST_BASE),
.length = SZ_4K,
.type = MT_DEVICE,
}, {
.virtual = IO_ADDRESS(REALVIEW_PBX_TILE_L220_BASE),
.pfn = __phys_to_pfn(REALVIEW_PBX_TILE_L220_BASE),
.length = SZ_8K,
.type = MT_DEVICE,
}
};
static void __init realview_pbx_map_io(void)
{
iotable_init(realview_pbx_io_desc, ARRAY_SIZE(realview_pbx_io_desc));
if (core_tile_pbx11mp() || core_tile_pbxa9mp())
iotable_init(realview_local_io_desc, ARRAY_SIZE(realview_local_io_desc));
}
static struct pl061_platform_data gpio0_plat_data = {
.gpio_base = 0,
};
static struct pl061_platform_data gpio1_plat_data = {
.gpio_base = 8,
};
static struct pl061_platform_data gpio2_plat_data = {
.gpio_base = 16,
};
static struct pl022_ssp_controller ssp0_plat_data = {
.bus_id = 0,
.enable_dma = 0,
.num_chipselect = 1,
};
/*
* RealView PBXCore AMBA devices
*/
#define GPIO2_IRQ { IRQ_PBX_GPIO2 }
#define GPIO3_IRQ { IRQ_PBX_GPIO3 }
#define AACI_IRQ { IRQ_PBX_AACI }
#define MMCI0_IRQ { IRQ_PBX_MMCI0A, IRQ_PBX_MMCI0B }
#define KMI0_IRQ { IRQ_PBX_KMI0 }
#define KMI1_IRQ { IRQ_PBX_KMI1 }
#define PBX_SMC_IRQ { }
#define MPMC_IRQ { }
#define PBX_CLCD_IRQ { IRQ_PBX_CLCD }
#define DMAC_IRQ { IRQ_PBX_DMAC }
#define SCTL_IRQ { }
#define PBX_WATCHDOG_IRQ { IRQ_PBX_WATCHDOG }
#define PBX_GPIO0_IRQ { IRQ_PBX_GPIO0 }
#define GPIO1_IRQ { IRQ_PBX_GPIO1 }
#define PBX_RTC_IRQ { IRQ_PBX_RTC }
#define SCI_IRQ { IRQ_PBX_SCI }
#define PBX_UART0_IRQ { IRQ_PBX_UART0 }
#define PBX_UART1_IRQ { IRQ_PBX_UART1 }
#define PBX_UART2_IRQ { IRQ_PBX_UART2 }
#define PBX_UART3_IRQ { IRQ_PBX_UART3 }
#define PBX_SSP_IRQ { IRQ_PBX_SSP }
/* FPGA Primecells */
APB_DEVICE(aaci, "fpga:aaci", AACI, NULL);
APB_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
APB_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
APB_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
APB_DEVICE(uart3, "fpga:uart3", PBX_UART3, NULL);
/* DevChip Primecells */
AHB_DEVICE(smc, "dev:smc", PBX_SMC, NULL);
AHB_DEVICE(sctl, "dev:sctl", SCTL, NULL);
APB_DEVICE(wdog, "dev:wdog", PBX_WATCHDOG, NULL);
APB_DEVICE(gpio0, "dev:gpio0", PBX_GPIO0, &gpio0_plat_data);
APB_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
APB_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
APB_DEVICE(rtc, "dev:rtc", PBX_RTC, NULL);
APB_DEVICE(sci0, "dev:sci0", SCI, NULL);
APB_DEVICE(uart0, "dev:uart0", PBX_UART0, NULL);
APB_DEVICE(uart1, "dev:uart1", PBX_UART1, NULL);
APB_DEVICE(uart2, "dev:uart2", PBX_UART2, NULL);
APB_DEVICE(ssp0, "dev:ssp0", PBX_SSP, &ssp0_plat_data);
/* Primecells on the NEC ISSP chip */
AHB_DEVICE(clcd, "issp:clcd", PBX_CLCD, &clcd_plat_data);
AHB_DEVICE(dmac, "issp:dmac", DMAC, NULL);
static struct amba_device *amba_devs[] __initdata = {
&dmac_device,
&uart0_device,
&uart1_device,
&uart2_device,
&uart3_device,
&smc_device,
&clcd_device,
&sctl_device,
&wdog_device,
&gpio0_device,
&gpio1_device,
&gpio2_device,
&rtc_device,
&sci0_device,
&ssp0_device,
&aaci_device,
&mmc0_device,
&kmi0_device,
&kmi1_device,
};
/*
* RealView PB-X platform devices
*/
static struct resource realview_pbx_flash_resources[] = {
[0] = {
.start = REALVIEW_PBX_FLASH0_BASE,
.end = REALVIEW_PBX_FLASH0_BASE + REALVIEW_PBX_FLASH0_SIZE - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = REALVIEW_PBX_FLASH1_BASE,
.end = REALVIEW_PBX_FLASH1_BASE + REALVIEW_PBX_FLASH1_SIZE - 1,
.flags = IORESOURCE_MEM,
},
};
static struct resource realview_pbx_smsc911x_resources[] = {
[0] = {
.start = REALVIEW_PBX_ETH_BASE,
.end = REALVIEW_PBX_ETH_BASE + SZ_64K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = IRQ_PBX_ETH,
.end = IRQ_PBX_ETH,
.flags = IORESOURCE_IRQ,
},
};
static struct resource realview_pbx_isp1761_resources[] = {
[0] = {
.start = REALVIEW_PBX_USB_BASE,
.end = REALVIEW_PBX_USB_BASE + SZ_128K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = IRQ_PBX_USB,
.end = IRQ_PBX_USB,
.flags = IORESOURCE_IRQ,
},
};
#ifdef CONFIG_CACHE_L2X0
static struct resource pmu_resources[] = {
[0] = {
.start = IRQ_PBX_PMU_CPU0,
.end = IRQ_PBX_PMU_CPU0,
.flags = IORESOURCE_IRQ,
},
[1] = {
.start = IRQ_PBX_PMU_CPU1,
.end = IRQ_PBX_PMU_CPU1,
.flags = IORESOURCE_IRQ,
},
[2] = {
.start = IRQ_PBX_PMU_CPU2,
.end = IRQ_PBX_PMU_CPU2,
.flags = IORESOURCE_IRQ,
},
[3] = {
.start = IRQ_PBX_PMU_CPU3,
.end = IRQ_PBX_PMU_CPU3,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device pmu_device = {
.name = "armv7-pmu",
.id = -1,
.num_resources = ARRAY_SIZE(pmu_resources),
.resource = pmu_resources,
};
#endif
static void __init gic_init_irq(void)
{
/* ARM PBX on-board GIC */
if (core_tile_pbx11mp() || core_tile_pbxa9mp()) {
gic_init(0, 29, __io_address(REALVIEW_PBX_TILE_GIC_DIST_BASE),
__io_address(REALVIEW_PBX_TILE_GIC_CPU_BASE));
} else {
gic_init(0, IRQ_PBX_GIC_START,
__io_address(REALVIEW_PBX_GIC_DIST_BASE),
__io_address(REALVIEW_PBX_GIC_CPU_BASE));
}
}
#ifdef CONFIG_HAVE_ARM_TWD
static DEFINE_TWD_LOCAL_TIMER(twd_local_timer,
REALVIEW_PBX_TILE_TWD_BASE,
IRQ_LOCALTIMER);
static void __init realview_pbx_twd_init(void)
{
int err = twd_local_timer_register(&twd_local_timer);
if (err)
pr_err("twd_local_timer_register failed %d\n", err);
}
#else
#define realview_pbx_twd_init() do { } while(0)
#endif
static void __init realview_pbx_timer_init(void)
{
timer0_va_base = __io_address(REALVIEW_PBX_TIMER0_1_BASE);
timer1_va_base = __io_address(REALVIEW_PBX_TIMER0_1_BASE) + 0x20;
timer2_va_base = __io_address(REALVIEW_PBX_TIMER2_3_BASE);
timer3_va_base = __io_address(REALVIEW_PBX_TIMER2_3_BASE) + 0x20;
realview_clk_init(__io_address(REALVIEW_SYS_BASE), false);
realview_timer_init(IRQ_PBX_TIMER0_1);
realview_pbx_twd_init();
}
static void realview_pbx_fixup(struct tag *tags, char **from)
{
#ifdef CONFIG_SPARSEMEM
/*
* Memory configuration with SPARSEMEM enabled on RealView PBX (see
* asm/mach/memory.h for more information).
*/
memblock_add(0, SZ_256M);
memblock_add(0x20000000, SZ_512M);
memblock_add(0x80000000, SZ_256M);
#else
realview_fixup(tags, from);
#endif
}
static void realview_pbx_restart(enum reboot_mode mode, const char *cmd)
{
void __iomem *reset_ctrl = __io_address(REALVIEW_SYS_RESETCTL);
void __iomem *lock_ctrl = __io_address(REALVIEW_SYS_LOCK);
/*
* To reset, we hit the on-board reset register
* in the system FPGA
*/
__raw_writel(REALVIEW_SYS_LOCK_VAL, lock_ctrl);
__raw_writel(0x00F0, reset_ctrl);
__raw_writel(0x00F4, reset_ctrl);
dsb();
}
static void __init realview_pbx_init(void)
{
int i;
#ifdef CONFIG_CACHE_L2X0
if (core_tile_pbxa9mp()) {
void __iomem *l2x0_base =
__io_address(REALVIEW_PBX_TILE_L220_BASE);
/* set RAM latencies to 1 cycle for eASIC */
writel(0, l2x0_base + L310_TAG_LATENCY_CTRL);
writel(0, l2x0_base + L310_DATA_LATENCY_CTRL);
/* 16KB way size, 8-way associativity, parity disabled
* Bits: .. 0 0 0 0 1 00 1 0 1 001 0 000 0 .... .... .... */
l2x0_init(l2x0_base, 0x02520000, 0xc0000fff);
platform_device_register(&pmu_device);
}
#endif
realview_flash_register(realview_pbx_flash_resources,
ARRAY_SIZE(realview_pbx_flash_resources));
realview_eth_register(NULL, realview_pbx_smsc911x_resources);
platform_device_register(&realview_i2c_device);
platform_device_register(&realview_cf_device);
platform_device_register(&realview_leds_device);
realview_usb_register(realview_pbx_isp1761_resources);
for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
struct amba_device *d = amba_devs[i];
amba_device_register(d, &iomem_resource);
}
}
MACHINE_START(REALVIEW_PBX, "ARM-RealView PBX")
/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
.atag_offset = 0x100,
.smp = smp_ops(realview_smp_ops),
.fixup = realview_pbx_fixup,
.map_io = realview_pbx_map_io,
.init_early = realview_init_early,
.init_irq = gic_init_irq,
.init_time = realview_pbx_timer_init,
.init_machine = realview_pbx_init,
#ifdef CONFIG_ZONE_DMA
.dma_zone_size = SZ_256M,
#endif
.restart = realview_pbx_restart,
MACHINE_END
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment