e1000e: Feature Enable PHY Ultra Low Power Mode (ULP)

ULP is a power saving feature that reduces the power consumption of the
PHY when a cable is not connected.

ULP is gated on the following conditions:
1) The hardware must support ULP.  Currently this is only I218
   devices from Intel
2) ULP is initiated by the driver, so, no driver results in no ULP.
3) ULP's implementation utilizes Runtime Power Management to toggle its
   execution.  ULP is enabled/disabled based on the state of Runtime PM.
4) ULP is not active when wake-on-unicast, multicast or broadcast is active
   as these features are mutually-exclusive.

Since the PHY is in an unavailable state while ULP is active, any access
of the PHY registers will fail.  This is resolved by utilizing kernel
calls that cause the device to exit Runtime PM (e.g. pm_runtime_get_sync)
and then, after PHY access is complete,  allow the device to resume
Runtime PM (e.g. pm_runtime_put_sync).

Under certain conditions, toggling the LANPHYPC is necessary to disable
ULP mode.  Break out existing code to toggle LANPHYPC to a new function
to avoid code duplication.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

drivers/net/ethernet/intel/e1000e/defines.h

@@ -30,6 +30,8 @@
 /* Wake Up Control */
 #define E1000_WUC_APME		0x00000001	/* APM Enable */
 #define E1000_WUC_PME_EN	0x00000002	/* PME Enable */
+#define E1000_WUC_PME_STATUS	0x00000004	/* PME Status */
+#define E1000_WUC_APMPME	0x00000008	/* Assert PME on APM Wakeup */
 #define E1000_WUC_PHY_WAKE	0x00000100	/* if PHY supports wakeup */
 
 /* Wake Up Filter Control */

drivers/net/ethernet/intel/e1000e/hw.h

@@ -648,12 +648,20 @@ struct e1000_shadow_ram {
 
 #define E1000_ICH8_SHADOW_RAM_WORDS		2048
 
+/* I218 PHY Ultra Low Power (ULP) states */
+enum e1000_ulp_state {
+	e1000_ulp_state_unknown,
+	e1000_ulp_state_off,
+	e1000_ulp_state_on,
+};
+
 struct e1000_dev_spec_ich8lan {
 	bool kmrn_lock_loss_workaround_enabled;
 	struct e1000_shadow_ram shadow_ram[E1000_ICH8_SHADOW_RAM_WORDS];
 	bool nvm_k1_enabled;
 	bool eee_disable;
 	u16 eee_lp_ability;
+	enum e1000_ulp_state ulp_state;
 };
 
 struct e1000_hw {

drivers/net/ethernet/intel/e1000e/ich8lan.h

@@ -58,11 +58,16 @@
 
 #define E1000_FWSM_WLOCK_MAC_MASK	0x0380
 #define E1000_FWSM_WLOCK_MAC_SHIFT	7
+#define E1000_FWSM_ULP_CFG_DONE		0x00000400	/* Low power cfg done */
 
 /* Shared Receive Address Registers */
 #define E1000_SHRAL_PCH_LPT(_i)		(0x05408 + ((_i) * 8))
 #define E1000_SHRAH_PCH_LPT(_i)		(0x0540C + ((_i) * 8))
 
+#define E1000_H2ME		0x05B50	/* Host to ME */
+#define E1000_H2ME_ULP		0x00000800	/* ULP Indication Bit */
+#define E1000_H2ME_ENFORCE_SETTINGS	0x00001000	/* Enforce Settings */
+
 #define ID_LED_DEFAULT_ICH8LAN	((ID_LED_DEF1_DEF2 << 12) | \
 				 (ID_LED_OFF1_OFF2 <<  8) | \
 				 (ID_LED_OFF1_ON2  <<  4) | \
@@ -75,6 +80,9 @@
 
 #define E1000_ICH8_LAN_INIT_TIMEOUT	1500
 
+/* FEXT register bit definition */
+#define E1000_FEXT_PHY_CABLE_DISCONNECTED	0x00000004
+
 #define E1000_FEXTNVM_SW_CONFIG		1
 #define E1000_FEXTNVM_SW_CONFIG_ICH8M	(1 << 27)	/* different on ICH8M */
 
@@ -88,6 +96,8 @@
 #define E1000_FEXTNVM6_REQ_PLL_CLK	0x00000100
 #define E1000_FEXTNVM6_ENABLE_K1_ENTRY_CONDITION	0x00000200
 
+#define E1000_FEXTNVM7_DISABLE_SMB_PERST	0x00000020
+
 #define PCIE_ICH8_SNOOP_ALL	PCIE_NO_SNOOP_ALL
 
 #define E1000_ICH_RAR_ENTRIES	7
@@ -154,6 +164,16 @@
 #define CV_SMB_CTRL		PHY_REG(769, 23)
 #define CV_SMB_CTRL_FORCE_SMBUS	0x0001
 
+/* I218 Ultra Low Power Configuration 1 Register */
+#define I218_ULP_CONFIG1		PHY_REG(779, 16)
+#define I218_ULP_CONFIG1_START		0x0001	/* Start auto ULP config */
+#define I218_ULP_CONFIG1_IND		0x0004	/* Pwr up from ULP indication */
+#define I218_ULP_CONFIG1_STICKY_ULP	0x0010	/* Set sticky ULP mode */
+#define I218_ULP_CONFIG1_INBAND_EXIT	0x0020	/* Inband on ULP exit */
+#define I218_ULP_CONFIG1_WOL_HOST	0x0040	/* WoL Host on ULP exit */
+#define I218_ULP_CONFIG1_RESET_TO_SMBUS	0x0100	/* Reset to SMBus mode */
+#define I218_ULP_CONFIG1_DISABLE_SMB_PERST	0x1000	/* Disable on PERST# */
+
 /* SMBus Address Phy Register */
 #define HV_SMB_ADDR		PHY_REG(768, 26)
 #define HV_SMB_ADDR_MASK	0x007F
@@ -188,6 +208,7 @@
 /* PHY Power Management Control */
 #define HV_PM_CTRL		PHY_REG(770, 17)
 #define HV_PM_CTRL_PLL_STOP_IN_K1_GIGA	0x100
+#define HV_PM_CTRL_K1_ENABLE		0x4000
 
 #define SW_FLAG_TIMEOUT		1000	/* SW Semaphore flag timeout in ms */
 
@@ -262,4 +283,5 @@ s32 e1000_lv_jumbo_workaround_ich8lan(struct e1000_hw *hw, bool enable);
 s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data);
 s32 e1000_write_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 data);
 s32 e1000_set_eee_pchlan(struct e1000_hw *hw);
+s32 e1000_enable_ulp_lpt_lp(struct e1000_hw *hw, bool to_sx);
 #endif /* _E1000E_ICH8LAN_H_ */

drivers/net/ethernet/intel/e1000e/netdev.c

@@ -5856,7 +5856,7 @@ static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
 static int e1000_init_phy_wakeup(struct e1000_adapter *adapter, u32 wufc)
 {
 	struct e1000_hw *hw = &adapter->hw;
-	u32 i, mac_reg;
+	u32 i, mac_reg, wuc;
 	u16 phy_reg, wuc_enable;
 	int retval;
 
@@ -5903,13 +5903,18 @@ static int e1000_init_phy_wakeup(struct e1000_adapter *adapter, u32 wufc)
 		phy_reg |= BM_RCTL_RFCE;
 	hw->phy.ops.write_reg_page(&adapter->hw, BM_RCTL, phy_reg);
 
+	wuc = E1000_WUC_PME_EN;
+	if (wufc & (E1000_WUFC_MAG | E1000_WUFC_LNKC))
+		wuc |= E1000_WUC_APME;
+
 	/* enable PHY wakeup in MAC register */
 	ew32(WUFC, wufc);
-	ew32(WUC, E1000_WUC_PHY_WAKE | E1000_WUC_PME_EN);
+	ew32(WUC, (E1000_WUC_PHY_WAKE | E1000_WUC_APMPME |
+		   E1000_WUC_PME_STATUS | wuc));
 
 	/* configure and enable PHY wakeup in PHY registers */
 	hw->phy.ops.write_reg_page(&adapter->hw, BM_WUFC, wufc);
-	hw->phy.ops.write_reg_page(&adapter->hw, BM_WUC, E1000_WUC_PME_EN);
+	hw->phy.ops.write_reg_page(&adapter->hw, BM_WUC, wuc);
 
 	/* activate PHY wakeup */
 	wuc_enable |= BM_WUC_ENABLE_BIT | BM_WUC_HOST_WU_BIT;
@@ -6012,8 +6017,19 @@ static int __e1000_shutdown(struct pci_dev *pdev, bool runtime)
 		e1000_power_down_phy(adapter);
 	}
 
-	if (adapter->hw.phy.type == e1000_phy_igp_3)
+	if (adapter->hw.phy.type == e1000_phy_igp_3) {
 		e1000e_igp3_phy_powerdown_workaround_ich8lan(&adapter->hw);
+	} else if (hw->mac.type == e1000_pch_lpt) {
+		if (!(wufc & (E1000_WUFC_EX | E1000_WUFC_MC | E1000_WUFC_BC)))
+			/* ULP does not support wake from unicast, multicast
+			 * or broadcast.
+			 */
+			retval = e1000_enable_ulp_lpt_lp(hw, !runtime);
+
+		if (retval)
+			return retval;
+	}
+
 
 	/* Release control of h/w to f/w.  If f/w is AMT enabled, this
 	 * would have already happened in close and is redundant.

drivers/net/ethernet/intel/e1000e/regs.h

@@ -32,6 +32,7 @@
 #define E1000_SCTL	0x00024	/* SerDes Control - RW */
 #define E1000_FCAL	0x00028	/* Flow Control Address Low - RW */
 #define E1000_FCAH	0x0002C	/* Flow Control Address High -RW */
+#define E1000_FEXT	0x0002C	/* Future Extended - RW */
 #define E1000_FEXTNVM	0x00028	/* Future Extended NVM - RW */
 #define E1000_FEXTNVM3	0x0003C	/* Future Extended NVM 3 - RW */
 #define E1000_FEXTNVM4	0x00024	/* Future Extended NVM 4 - RW */