Merge tag 'pinctrl-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control bulk updates from Linus Walleij:
 "New drivers:

   - Qualcomm SDM845: this is their new flagship SoC platform which
     seems to be targeted at premium mobile handsets.

   - Renesas R-Car M3-N SoC.

   - Renesas R8A77980 SoC.

   - NXP (ex Freescale) i.MX 6SLL SoC.

   - Mediatek MT2712 SoC.

   - Allwinner H6 SoC.

  Improvements:

   - Uniphier adds a few new functions and pins.

   - Renesas refactorings and additional pin definitions.

   - Improved pin groups for Axis Artpec6.

  Cleanup:

   - Drop the TZ1090 drivers. This platform is no longer maintained and
     is being deleted.

   - Drop ST-Ericsson U8540/U9540 support as this was never
     productified.

   - Overall minor fixes and janitorial"

* tag 'pinctrl-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
  pinctrl: uniphier: add UART hardware flow control pin-mux settings
  pinctrl: sunxi: add support for the Allwinner H6 main pin controller
  pinctrl: sunxi: change irq_bank_base to irq_bank_map
  pinctrl: sunxi: introduce IRQ bank conversion function
  pinctrl: sunxi: refactor irq related register function to have desc
  pinctrl: msm8998: Remove owner assignment from platform_driver
  pinctrl: uniphier: divide I2S and S/PDIF audio out pin-mux group
  pinctrl: uniphier: add PXs2 Audio in/out pin-mux settings
  pinctrl/amd: poll InterruptEnable bits in enable_irq
  pinctrl: ocelot: fix gpio direction
  pinctrl: mtk: fix check warnings.
  pintcrl: mtk: support bias-disable of generic and special pins simultaneously
  pinctrl: add mt2712 pinctrl driver
  pinctrl: pinctrl-single: Fix pcs_request_gpio() when bits_per_mux != 0
  pinctrl: imx: Add pinctrl driver support for imx6sll
  dt-bindings: imx: update pinctrl doc for imx6sll
  pinctrl: intel: Implement intel_gpio_get_direction callback
  pinctrl: stm32: add 'depends on HAS_IOMEM' to fix unmet dependency
  pinctrl: mediatek: mtk-common: use true and false for boolean values
  pinctrl: sunxi: always look for apb block
  ...

Documentation/devicetree/bindings/pinctrl/actions,s900-pinctrl.txt

+Actions Semi S900 Pin Controller
+
+This binding describes the pin controller found in the S900 SoC.
+
+Required Properties:
+
+- compatible:   Should be "actions,s900-pinctrl"
+- reg:          Should contain the register base address and size of
+                the pin controller.
+- clocks:       phandle of the clock feeding the pin controller
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+PIN CONFIGURATION NODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+Pinmux functions are available only for the pin groups while pinconf
+parameters are available for both pin groups and individual pins.
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+Required Properties:
+
+- pins:           An array of strings, each string containing the name of a pin.
+                  These pins are used for selecting the pull control and schmitt
+                  trigger parameters. The following are the list of pins
+                  available:
+
+                  eth_txd0, eth_txd1, eth_txen, eth_rxer, eth_crs_dv,
+                  eth_rxd1, eth_rxd0, eth_ref_clk, eth_mdc, eth_mdio,
+                  sirq0, sirq1, sirq2, i2s_d0, i2s_bclk0, i2s_lrclk0,
+                  i2s_mclk0, i2s_d1, i2s_bclk1, i2s_lrclk1, i2s_mclk1,
+                  pcm1_in, pcm1_clk, pcm1_sync, pcm1_out, eram_a5,
+                  eram_a6, eram_a7, eram_a8, eram_a9, eram_a10, eram_a11,
+                  lvds_oep, lvds_oen, lvds_odp, lvds_odn, lvds_ocp,
+                  lvds_ocn, lvds_obp, lvds_obn, lvds_oap, lvds_oan,
+                  lvds_eep, lvds_een, lvds_edp, lvds_edn, lvds_ecp,
+                  lvds_ecn, lvds_ebp, lvds_ebn, lvds_eap, lvds_ean,
+                  sd0_d0, sd0_d1, sd0_d2, sd0_d3, sd1_d0, sd1_d1,
+                  sd1_d2, sd1_d3, sd0_cmd, sd0_clk, sd1_cmd, sd1_clk,
+                  spi0_sclk, spi0_ss, spi0_miso, spi0_mosi, uart0_rx,
+                  uart0_tx, uart2_rx, uart2_tx, uart2_rtsb, uart2_ctsb,
+                  uart3_rx, uart3_tx, uart3_rtsb, uart3_ctsb, uart4_rx,
+                  uart4_tx, i2c0_sclk, i2c0_sdata, i2c1_sclk, i2c1_sdata,
+                  i2c2_sclk, i2c2_sdata, csi0_dn0, csi0_dp0, csi0_dn1,
+                  csi0_dp1, csi0_cn, csi0_cp, csi0_dn2, csi0_dp2, csi0_dn3,
+                  csi0_dp3, dsi_dp3, dsi_dn3, dsi_dp1, dsi_dn1, dsi_cp,
+                  dsi_cn, dsi_dp0, dsi_dn0, dsi_dp2, dsi_dn2, sensor0_pclk,
+                  csi1_dn0,csi1_dp0,csi1_dn1, csi1_dp1, csi1_cn, csi1_cp,
+                  sensor0_ckout, nand0_d0, nand0_d1, nand0_d2, nand0_d3,
+                  nand0_d4, nand0_d5, nand0_d6, nand0_d7, nand0_dqs,
+                  nand0_dqsn, nand0_ale, nand0_cle, nand0_ceb0, nand0_ceb1,
+                  nand0_ceb2, nand0_ceb3, nand1_d0, nand1_d1, nand1_d2,
+                  nand1_d3, nand1_d4, nand1_d5, nand1_d6, nand1_d7, nand1_dqs,
+                  nand1_dqsn, nand1_ale, nand1_cle, nand1_ceb0, nand1_ceb1,
+                  nand1_ceb2, nand1_ceb3, sgpio0, sgpio1, sgpio2, sgpio3
+
+- groups:         An array of strings, each string containing the name of a pin
+                  group. These pin groups are used for selecting the pinmux
+                  functions.
+
+                  lvds_oxx_uart4_mfp, rmii_mdc_mfp, rmii_mdio_mfp, sirq0_mfp,
+                  sirq1_mfp, rmii_txd0_mfp, rmii_txd1_mfp, rmii_txen_mfp,
+                  rmii_rxer_mfp, rmii_crs_dv_mfp, rmii_rxd1_mfp, rmii_rxd0_mfp,
+                  rmii_ref_clk_mfp, i2s_d0_mfp, i2s_d1_mfp, i2s_lr_m_clk0_mfp,
+                  i2s_bclk0_mfp, i2s_bclk1_mclk1_mfp, pcm1_in_out_mfp,
+                  pcm1_clk_mfp, pcm1_sync_mfp, eram_a5_mfp, eram_a6_mfp,
+                  eram_a7_mfp, eram_a8_mfp, eram_a9_mfp, eram_a10_mfp,
+                  eram_a11_mfp, lvds_oep_odn_mfp, lvds_ocp_obn_mfp,
+                  lvds_oap_oan_mfp, lvds_e_mfp, spi0_sclk_mosi_mfp, spi0_ss_mfp,
+                  spi0_miso_mfp, uart2_rtsb_mfp, uart2_ctsb_mfp, uart3_rtsb_mfp,
+                  uart3_ctsb_mfp, sd0_d0_mfp, sd0_d1_mfp, sd0_d2_d3_mfp,
+                  sd1_d0_d3_mfp, sd0_cmd_mfp, sd0_clk_mfp, sd1_cmd_clk_mfp,
+                  uart0_rx_mfp, nand0_d0_ceb3_mfp, uart0_tx_mfp, i2c0_mfp,
+                  csi0_cn_cp_mfp, csi0_dn0_dp3_mfp, csi1_dn0_cp_mfp,
+                  dsi_dp3_dn1_mfp, dsi_cp_dn0_mfp, dsi_dp2_dn2_mfp,
+                  nand1_d0_ceb1_mfp, nand1_ceb3_mfp, nand1_ceb0_mfp,
+                  csi1_dn0_dp0_mfp, uart4_rx_tx_mfp
+
+
+                  These pin groups are used for selecting the drive strength
+                  parameters.
+
+                  sgpio3_drv, sgpio2_drv, sgpio1_drv, sgpio0_drv,
+                  rmii_tx_d0_d1_drv, rmii_txen_rxer_drv, rmii_crs_dv_drv,
+                  rmii_rx_d1_d0_drv, rmii_ref_clk_drv, rmii_mdc_mdio_drv,
+                  sirq_0_1_drv, sirq2_drv, i2s_d0_d1_drv, i2s_lr_m_clk0_drv,
+                  i2s_blk1_mclk1_drv, pcm1_in_out_drv, lvds_oap_oan_drv,
+                  lvds_oep_odn_drv, lvds_ocp_obn_drv, lvds_e_drv, sd0_d3_d0_drv,
+                  sd1_d3_d0_drv, sd0_sd1_cmd_clk_drv, spi0_sclk_mosi_drv,
+                  spi0_ss_miso_drv, uart0_rx_tx_drv, uart4_rx_tx_drv, uart2_drv,
+                  uart3_drv, i2c0_drv, i2c1_drv, i2c2_drv, sensor0_drv
+
+                  These pin groups are used for selecting the slew rate
+                  parameters.
+
+                  sgpio3_sr, sgpio2_sr, sgpio1_sr, sgpio0_sr, rmii_tx_d0_d1_sr,
+                  rmii_txen_rxer_sr, rmii_crs_dv_sr, rmii_rx_d1_d0_sr,
+                  rmii_ref_clk_sr, rmii_mdc_mdio_sr, sirq_0_1_sr, sirq2_sr,
+                  i2s_do_d1_sr, i2s_lr_m_clk0_sr, i2s_bclk0_mclk1_sr,
+                  pcm1_in_out_sr, sd1_d3_d0_sr, sd0_sd1_clk_cmd_sr,
+                  spi0_sclk_mosi_sr, spi0_ss_miso_sr, uart0_rx_tx_sr,
+                  uart4_rx_tx_sr, uart2_sr, uart3_sr, i2c0_sr, i2c1_sr, i2c2_sr,
+                  sensor0_sr
+
+- function:       An array of strings, each string containing the name of the
+                  pinmux functions. These functions can only be selected by
+                  the corresponding pin groups. The following are the list of
+                  pinmux functions available:
+
+                  eram, eth_rmii, eth_smii, spi0, spi1, spi2, spi3, sens0,
+                  uart0, uart1, uart2, uart3, uart4, uart5, uart6, i2s0, i2s1,
+                  pcm0, pcm1, jtag, pwm0, pwm1, pwm2, pwm3, pwm4, pwm5, sd0,
+                  sd1, sd2, sd3, i2c0, i2c1, i2c2, i2c3, i2c4, i2c5, lvds,
+                  usb30, usb20, gpu, mipi_csi0, mipi_csi1, mipi_dsi, nand0,
+                  nand1, spdif, sirq0, sirq1, sirq2
+
+Optional Properties:
+
+- bias-bus-hold:  No arguments. The specified pins should retain the previous
+                  state value.
+- bias-high-impedance: No arguments. The specified pins should be configured
+                  as high impedance.
+- bias-pull-down: No arguments. The specified pins should be configured as
+                  pull down.
+- bias-pull-up:   No arguments. The specified pins should be configured as
+                  pull up.
+- input-schmitt-enable: No arguments: Enable schmitt trigger for the specified
+                  pins
+- input-schmitt-disable: No arguments: Disable schmitt trigger for the specified
+                  pins
+- slew-rate:      Integer. Sets slew rate for the specified pins.
+                  Valid values are:
+                  <0>  - Slow
+                  <1>  - Fast
+- drive-strength: Integer. Selects the drive strength for the specified
+                  pins in mA.
+                  Valid values are:
+                  <2>
+                  <4>
+                  <8>
+                  <12>
+
+Example:
+
+          pinctrl: pinctrl@e01b0000 {
+                  compatible = "actions,s900-pinctrl";
+                  reg = <0x0 0xe01b0000 0x0 0x1000>;
+                  clocks = <&cmu CLK_GPIO>;
+
+                  uart2-default: uart2-default {
+                          pinmux {
+                                  groups = "lvds_oep_odn_mfp";
+                                  function = "uart2";
+                          };
+                          pinconf {
+                                  groups = "lvds_oep_odn_drv";
+                                  drive-strength = <12>;
+                          };
+                  };
+          };

Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt

@@ -27,6 +27,7 @@ Required properties:
   "allwinner,sun50i-a64-pinctrl"
   "allwinner,sun50i-a64-r-pinctrl"
   "allwinner,sun50i-h5-pinctrl"
+  "allwinner,sun50i-h6-pinctrl"
   "nextthing,gr8-pinctrl"
 
 - reg: Should contain the register physical address and length for the

Documentation/devicetree/bindings/pinctrl/axis,artpec6-pinctrl.txt

@@ -19,8 +19,10 @@ Required subnode-properties:
 	Available functions and groups (function: group0, group1...):
 		gpio: cpuclkoutgrp0, udlclkoutgrp0, i2c1grp0, i2c2grp0,
 		      i2c3grp0, i2s0grp0, i2s1grp0, i2srefclkgrp0, spi0grp0,
-		      spi1grp0, pciedebuggrp0, uart0grp0, uart0grp1, uart1grp0,
-		      uart2grp0, uart2grp1, uart3grp0, uart4grp0, uart5grp0
+		      spi1grp0, pciedebuggrp0, uart0grp0, uart0grp1, uart0grp2,
+		      uart1grp0, uart1grp1, uart2grp0, uart2grp1, uart2grp2,
+		      uart3grp0, uart4grp0, uart4grp1, uart5grp0, uart5grp1,
+		      uart5nocts
 		cpuclkout: cpuclkoutgrp0
 		udlclkout: udlclkoutgrp0
 		i2c1: i2c1grp0
@@ -32,12 +34,12 @@ Required subnode-properties:
 		spi0: spi0grp0
 		spi1: spi1grp0
 		pciedebug: pciedebuggrp0
-		uart0: uart0grp0, uart0grp1
-		uart1: uart1grp0
-		uart2: uart2grp0, uart2grp1
+		uart0: uart0grp0, uart0grp1, uart0grp2
+		uart1: uart1grp0, uart1grp1
+		uart2: uart2grp0, uart2grp1, uart2grp2
 		uart3: uart3grp0
-		uart4: uart4grp0
-		uart5: uart5grp0
+		uart4: uart4grp0, uart4grp1
+		uart5: uart5grp0, uart5grp1, uart5nocts
 		nand: nandgrp0
 		sdio0: sdio0grp0
 		sdio1: sdio1grp0

Documentation/devicetree/bindings/pinctrl/fsl,imx6sll-pinctrl.txt

+* Freescale i.MX6 SLL IOMUX Controller
+
+Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
+and usage.
+
+Required properties:
+- compatible: "fsl,imx6sll-iomuxc"
+- fsl,pins: each entry consists of 6 integers and represents the mux and config
+  setting for one pin.  The first 5 integers <mux_reg conf_reg input_reg mux_val
+  input_val> are specified using a PIN_FUNC_ID macro, which can be found in
+  imx6sll-pinfunc.h under device tree source folder.  The last integer CONFIG is
+  the pad setting value like pull-up on this pin.  Please refer to i.MX6SLL
+  Reference Manual for detailed CONFIG settings.
+
+CONFIG bits definition:
+PAD_CTL_LVE			(1 << 22)
+PAD_CTL_HYS                     (1 << 16)
+PAD_CTL_PUS_100K_DOWN           (0 << 14)
+PAD_CTL_PUS_47K_UP              (1 << 14)
+PAD_CTL_PUS_100K_UP             (2 << 14)
+PAD_CTL_PUS_22K_UP              (3 << 14)
+PAD_CTL_PUE                     (1 << 13)
+PAD_CTL_PKE                     (1 << 12)
+PAD_CTL_ODE                     (1 << 11)
+PAD_CTL_SPEED_LOW               (0 << 6)
+PAD_CTL_SPEED_MED               (1 << 6)
+PAD_CTL_SPEED_HIGH              (3 << 6)
+PAD_CTL_DSE_DISABLE             (0 << 3)
+PAD_CTL_DSE_260ohm              (1 << 3)
+PAD_CTL_DSE_130ohm              (2 << 3)
+PAD_CTL_DSE_87ohm               (3 << 3)
+PAD_CTL_DSE_65ohm               (4 << 3)
+PAD_CTL_DSE_52ohm               (5 << 3)
+PAD_CTL_DSE_43ohm               (6 << 3)
+PAD_CTL_DSE_37ohm               (7 << 3)
+PAD_CTL_SRE_FAST                (1 << 0)
+PAD_CTL_SRE_SLOW                (0 << 0)
+
+Refer to imx6sll-pinfunc.h in device tree source folder for all available
+imx6sll PIN_FUNC_ID.

Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt

-ImgTec TZ1090 PDC pin controller
-
-Required properties:
-- compatible: "img,tz1090-pdc-pinctrl"
-- reg: Should contain the register physical address and length of the
-  SOC_GPIO_CONTROL registers in the PDC register region.
-
-Please refer to pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices, including the meaning of the
-phrase "pin configuration node".
-
-TZ1090-PDC's pin configuration nodes act as a container for an arbitrary number
-of subnodes. Each of these subnodes represents some desired configuration for a
-pin, a group, or a list of pins or groups. This configuration can include the
-mux function to select on those pin(s)/group(s), and various pin configuration
-parameters, such as pull-up, drive strength, etc.
-
-The name of each subnode is not important; all subnodes should be enumerated
-and processed purely based on their content.
-
-Each subnode only affects those parameters that are explicitly listed. In
-other words, a subnode that lists a mux function but no pin configuration
-parameters implies no information about any pin configuration parameters.
-Similarly, a pin subnode that describes a pullup parameter implies no
-information about e.g. the mux function. For this reason, even seemingly boolean
-values are actually tristates in this binding: unspecified, off, or on.
-Unspecified is represented as an absent property, and off/on are represented as
-integer values 0 and 1.
-
-Required subnode-properties:
-- tz1090,pins : An array of strings. Each string contains the name of a pin or
-  group. Valid values for these names are listed below.
-
-Optional subnode-properties:
-- tz1090,function: A string containing the name of the function to mux to the
-  pin or group. Valid values for function names are listed below, including
-  which pingroups can be muxed to them.
-- supported generic pinconfig properties (for further details see
-  Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt):
-  - bias-disable
-  - bias-high-impedance
-  - bias-bus-hold
-  - bias-pull-up
-  - bias-pull-down
-  - input-schmitt-enable
-  - input-schmitt-disable
-  - drive-strength: Integer, control drive strength of pins in mA.
-      2: 2mA
-      4: 4mA
-      8: 8mA
-      12: 12mA
-  - low-power-enable: Flag, power-on-start weak pull-down for invalid power.
-  - low-power-disable: Flag, power-on-start weak pull-down disabled.
-
-Note that many of these properties are only valid for certain specific pins
-or groups. See the TZ1090 TRM for complete details regarding which groups
-support which functionality. The Linux pinctrl driver may also be a useful
-reference.
-
-Valid values for pin and group names are:
-
-  pins:
-
-    These all support bias-high-impediance, bias-pull-up, bias-pull-down, and
-    bias-bus-hold (which can also be provided to any of the groups below to set
-    it for all gpio pins in that group).
-
-    gpio0, gpio1, sys_wake0, sys_wake1, sys_wake2, ir_data, ext_power.
-
-  mux groups:
-
-    These all support function.
-
-    gpio0
-        pins:       gpio0.
-        function:   ir_mod_stable_out.
-    gpio1
-        pins:       gpio1.
-        function:   ir_mod_power_out.
-
-  drive groups:
-
-    These support input-schmitt-enable, input-schmitt-disable,
-    drive-strength, low-power-enable, and low-power-disable.
-
-    pdc
-        pins:   gpio0, gpio1, sys_wake0, sys_wake1, sys_wake2, ir_data,
-                ext_power.
-
-Example:
-
-	pinctrl_pdc: pinctrl@2006500 {
-		#gpio-range-cells = <3>;
-		compatible = "img,tz1090-pdc-pinctrl";
-		reg = <0x02006500 0x100>;
-	};
-
-Example board file extracts:
-
-	&pinctrl_pdc {
-		pinctrl-names = "default";
-		pinctrl-0 = <&syswake_default>;
-
-		syswake_default: syswakes {
-			syswake_cfg {
-				tz1090,pins =	"sys_wake0",
-						"sys_wake1",
-						"sys_wake2";
-				pull-up;
-			};
-		};
-		irmod_default: irmod {
-			gpio0_cfg {
-				tz1090,pins =	"gpio0";
-				tz1090,function = "ir_mod_stable_out";
-			};
-			gpio1_cfg {
-				tz1090,pins =	"gpio1";
-				tz1090,function = "ir_mod_power_out";
-			};
-		};
-	};
-
-	ir: ir@2006200 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&irmod_default>;
-	};

Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt

-ImgTec TZ1090 pin controller
-
-Required properties:
-- compatible: "img,tz1090-pinctrl"
-- reg: Should contain the register physical address and length of the pad
-  configuration registers (CR_PADS_* and CR_IF_CTL0).
-
-Please refer to pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices, including the meaning of the
-phrase "pin configuration node".
-
-TZ1090's pin configuration nodes act as a container for an arbitrary number of
-subnodes. Each of these subnodes represents some desired configuration for a
-pin, a group, or a list of pins or groups. This configuration can include the
-mux function to select on those pin(s)/group(s), and various pin configuration
-parameters, such as pull-up, drive strength, etc.
-
-The name of each subnode is not important; all subnodes should be enumerated
-and processed purely based on their content.
-
-Each subnode only affects those parameters that are explicitly listed. In
-other words, a subnode that lists a mux function but no pin configuration
-parameters implies no information about any pin configuration parameters.
-Similarly, a pin subnode that describes a pullup parameter implies no
-information about e.g. the mux function. For this reason, even seemingly boolean
-values are actually tristates in this binding: unspecified, off, or on.
-Unspecified is represented as an absent property, and off/on are represented as
-integer values 0 and 1.
-
-Required subnode-properties:
-- tz1090,pins : An array of strings. Each string contains the name of a pin or
-  group. Valid values for these names are listed below.
-
-Optional subnode-properties:
-- tz1090,function: A string containing the name of the function to mux to the
-  pin or group. Valid values for function names are listed below, including
-  which pingroups can be muxed to them.
-- supported generic pinconfig properties (for further details see
-  Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt):
-  - bias-disable
-  - bias-high-impedance
-  - bias-bus-hold
-  - bias-pull-up
-  - bias-pull-down
-  - input-schmitt-enable
-  - input-schmitt-disable
-  - drive-strength: Integer, control drive strength of pins in mA.
-      2: 2mA
-      4: 4mA
-      8: 8mA
-      12: 12mA
-
-
-Note that many of these properties are only valid for certain specific pins
-or groups. See the TZ1090 TRM for complete details regarding which groups
-support which functionality. The Linux pinctrl driver may also be a useful
-reference.
-
-Valid values for pin and group names are:
-
-  gpio pins:
-
-    These all support bias-high-impediance, bias-pull-up, bias-pull-down, and
-    bias-bus-hold (which can also be provided to any of the groups below to set
-    it for all pins in that group).
-
-    They also all support the some form of muxing. Any pins which are contained
-    in one of the mux groups (see below) can be muxed only to the functions
-    supported by the mux group. All other pins can be muxed to the "perip"
-    function which enables them with their intended peripheral.
-
-    Different pins in the same mux group cannot be muxed to different functions,
-    however it is possible to mux only a subset of the pins in a mux group to a
-    particular function and leave the remaining pins unmuxed. This is useful if
-    the board connects certain pins in a group to other devices to be controlled
-    by GPIO, and you don't want the usual peripheral to have any control of the
-    pin.
-
-    ant_sel0, ant_sel1, gain0, gain1, gain2, gain3, gain4, gain5, gain6, gain7,
-    i2s_bclk_out, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2, i2s_lrclk_out,
-    i2s_mclk, pa_on, pdm_a, pdm_b, pdm_c, pdm_d, pll_on, rx_hp, rx_on,
-    scb0_sclk, scb0_sdat, scb1_sclk, scb1_sdat, scb2_sclk, scb2_sdat, sdh_cd,
-    sdh_clk_in, sdh_wp, sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, sdio_d3,
-    spi0_cs0, spi0_cs1, spi0_cs2, spi0_din, spi0_dout, spi0_mclk, spi1_cs0,
-    spi1_cs1, spi1_cs2, spi1_din, spi1_dout, spi1_mclk, tft_blank_ls, tft_blue0,
-    tft_blue1, tft_blue2, tft_blue3, tft_blue4, tft_blue5, tft_blue6, tft_blue7,
-    tft_green0, tft_green1, tft_green2, tft_green3, tft_green4, tft_green5,
-    tft_green6, tft_green7, tft_hsync_nr, tft_panelclk, tft_pwrsave, tft_red0,
-    tft_red1, tft_red2, tft_red3, tft_red4, tft_red5, tft_red6, tft_red7,
-    tft_vd12acb, tft_vdden_gd, tft_vsync_ns, tx_on, uart0_cts, uart0_rts,
-    uart0_rxd, uart0_txd, uart1_rxd, uart1_txd.
-
-        bias-high-impediance:  supported.
-        bias-pull-up:          supported.
-        bias-pull-down:        supported.
-        bias-bus-hold:         supported.
-        function:              perip or those supported by pin's mux group.
-
-  other pins:
-
-    These other pins are part of various pin groups below, but can't be
-    controlled as GPIOs. They do however support bias-high-impediance,
-    bias-pull-up, bias-pull-down, and bias-bus-hold (which can also be provided
-    to any of the groups below to set it for all pins in that group).
-
-    clk_out0, clk_out1, tck, tdi, tdo, tms, trst.
-
-        bias-high-impediance:  supported.
-        bias-pull-up:          supported.
-        bias-pull-down:        supported.
-        bias-bus-hold:         supported.
-
-  mux groups:
-
-    These all support function, and some support drive configs.
-
-    afe
-        pins:                  tx_on, rx_on, pll_on, pa_on, rx_hp, ant_sel0,
-                               ant_sel1, gain0, gain1, gain2, gain3, gain4,
-                               gain5, gain6, gain7.
-        function:              afe, ts_out_0.
-        input-schmitt-enable:  supported.
-        input-schmitt-disable: supported.
-        drive-strength:        supported.
-    pdm_d
-        pins:                  pdm_d.
-        function:              pdm_dac, usb_vbus.
-    sdh
-        pins:                  sdh_cd, sdh_wp, sdh_clk_in.
-        function:              sdh, sdio.
-    sdio
-        pins:                  sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2,
-                               sdio_d3.
-        function:              sdio, sdh.
-    spi1_cs2
-        pins:                  spi1_cs2.
-        function:              spi1_cs2, usb_vbus.
-    tft
-        pins:                  tft_red0, tft_red1, tft_red2, tft_red3,
-                               tft_red4, tft_red5, tft_red6, tft_red7,
-                               tft_green0, tft_green1, tft_green2, tft_green3,
-                               tft_green4, tft_green5, tft_green6, tft_green7,
-                               tft_blue0, tft_blue1, tft_blue2, tft_blue3,
-                               tft_blue4, tft_blue5, tft_blue6, tft_blue7,
-                               tft_vdden_gd, tft_panelclk, tft_blank_ls,
-                               tft_vsync_ns, tft_hsync_nr, tft_vd12acb,
-                               tft_pwrsave.
-        function:              tft, ext_dac, not_iqadc_stb, iqdac_stb, ts_out_1,
-                               lcd_trace, phy_ringosc.
-        input-schmitt-enable:  supported.
-        input-schmitt-disable: supported.
-        drive-strength:        supported.
-
-  drive groups:
-
-    These all support input-schmitt-enable, input-schmitt-disable,
-    and drive-strength.
-
-    jtag
-        pins:   tck, trst, tdi, tdo, tms.
-    scb1
-        pins:   scb1_sdat, scb1_sclk.
-    scb2
-        pins:   scb2_sdat, scb2_sclk.
-    spi0
-        pins:   spi0_mclk, spi0_cs0, spi0_cs1, spi0_cs2, spi0_dout, spi0_din.
-    spi1
-        pins:   spi1_mclk, spi1_cs0, spi1_cs1, spi1_cs2, spi1_dout, spi1_din.
-    uart
-        pins:   uart0_txd, uart0_rxd, uart0_rts, uart0_cts,
-                uart1_txd, uart1_rxd.
-    drive_i2s
-        pins:   clk_out1, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2,
-                i2s_lrclk_out, i2s_bclk_out, i2s_mclk.
-    drive_pdm
-        pins:   clk_out0, pdm_b, pdm_a.
-    drive_scb0
-        pins:   scb0_sclk, scb0_sdat, pdm_d, pdm_c.
-    drive_sdio
-        pins:   sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, sdio_d3,
-                sdh_wp, sdh_cd, sdh_clk_in.
-
-  convenience groups:
-
-    These are just convenient groupings of pins and don't support any drive
-    configs.
-
-    uart0
-        pins:   uart0_cts, uart0_rts, uart0_rxd, uart0_txd.
-    uart1
-        pins:   uart1_rxd, uart1_txd.
-    scb0
-        pins:   scb0_sclk, scb0_sdat.
-    i2s
-        pins:   i2s_bclk_out, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2,
-                i2s_lrclk_out, i2s_mclk.
-
-Example:
-
-	pinctrl: pinctrl@2005800 {
-		#gpio-range-cells = <3>;
-		compatible = "img,tz1090-pinctrl";
-		reg = <0x02005800 0xe4>;
-	};
-
-Example board file extract:
-
-	&pinctrl {
-		uart0_default: uart0 {
-			uart0_cfg {
-				tz1090,pins =	"uart0_rxd",
-						"uart0_txd";
-				tz1090,function = "perip";
-			};
-		};
-		tft_default: tft {
-			tft_cfg {
-				tz1090,pins =	"tft";
-				tz1090,function = "tft";
-			};
-		};
-	};
-
-	uart@2004b00 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&uart0_default>;
-	};

Documentation/devicetree/bindings/pinctrl/pinctrl-mcp23s08.txt

@@ -45,6 +45,8 @@ Optional properties:
   - first cell is the pin number
   - second cell is used to specify flags.
 - interrupt-controller: Marks the device node as a interrupt controller.
+- drive-open-drain: Sets the ODR flag in the IOCON register. This configures
+        the IRQ output as open drain active low.
 
 Optional device specific properties:
 - microchip,irq-mirror: Sets the mirror flag in the IOCON register. Devices

Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt

@@ -76,12 +76,12 @@ Examples:
 
 ...
 {
-	syscfg_pctl_a: syscfg_pctl_a@10005000 {
+	syscfg_pctl_a: syscfg-pctl-a@10005000 {
 		compatible = "mediatek,mt8135-pctl-a-syscfg", "syscon";
 		reg = <0 0x10005000 0 0x1000>;
 	};
 
-	syscfg_pctl_b: syscfg_pctl_b@1020c020 {
+	syscfg_pctl_b: syscfg-pctl-b@1020c020 {
 		compatible = "mediatek,mt8135-pctl-b-syscfg", "syscon";
 		reg = <0 0x1020C020 0 0x1000>;
 	};

Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.txt

+Qualcomm SDM845 TLMM block
+
+This binding describes the Top Level Mode Multiplexer block found in the
+SDM845 platform.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be "qcom,sdm845-pinctrl"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: the base address and size of the TLMM register space.
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: should specify the TLMM summary IRQ.
+
+- interrupt-controller:
+	Usage: required
+	Value type: <none>
+	Definition: identifies this node as an interrupt controller
+
+- #interrupt-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 2. Specifying the pin number and flags, as defined
+		    in <dt-bindings/interrupt-controller/irq.h>
+
+- gpio-controller:
+	Usage: required
+	Value type: <none>
+	Definition: identifies this node as a gpio controller
+
+- #gpio-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 2. Specifying the pin number and flags, as defined
+		    in <dt-bindings/gpio/gpio.h>
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+
+PIN CONFIGURATION NODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+	Usage: required
+	Value type: <string-array>
+	Definition: List of gpio pins affected by the properties specified in
+		    this subnode.
+
+		    Valid pins are:
+		      gpio0-gpio149
+		        Supports mux, bias and drive-strength
+
+		      sdc2_clk, sdc2_cmd, sdc2_data
+		        Supports bias and drive-strength
+
+- function:
+	Usage: required
+	Value type: <string>
+	Definition: Specify the alternative function to be configured for the
+		    specified pins. Functions are only valid for gpio pins.
+		    Valid values are:
+
+		    gpio, adsp_ext, agera_pll, atest_char, atest_tsens,
+		    atest_tsens2, atest_usb1, atest_usb10, atest_usb11,
+		    atest_usb12, atest_usb13, atest_usb2, atest_usb20,
+		    atest_usb21, atest_usb22, atest_usb23, audio_ref,
+		    btfm_slimbus, cam_mclk, cci_async, cci_i2c, cci_timer0,
+		    cci_timer1, cci_timer2, cci_timer3, cci_timer4, cri_trng,
+		    cri_trng0, cri_trng1, dbg_out, ddr_bist, ddr_pxi0,
+		    ddr_pxi1, ddr_pxi2, ddr_pxi3, edp_hot, edp_lcd, gcc_gp1,
+		    gcc_gp2, gcc_gp3, jitter_bist, ldo_en, ldo_update,
+		    lpass_slimbus, m_voc, mdp_vsync, mdp_vsync0, mdp_vsync1,
+		    mdp_vsync2, mdp_vsync3, mss_lte, nav_pps, pa_indicator,
+		    pci_e0, pci_e1, phase_flag, pll_bist, pll_bypassnl,
+		    pll_reset, pri_mi2s, pri_mi2s_ws, prng_rosc, qdss_cti,
+		    qdss, qlink_enable, qlink_request, qua_mi2s, qup0, qup1,
+		    qup10, qup11, qup12, qup13, qup14, qup15, qup2, qup3, qup4,
+		    qup5, qup6, qup7, qup8, qup9, qup_l4, qup_l5, qup_l6,
+		    qspi_clk, qspi_cs, qspi_data, sd_write, sdc4_clk, sdc4_cmd,
+		    sdc4_data, sec_mi2s, sp_cmu, spkr_i2s, ter_mi2s, tgu_ch0,
+		    tgu_ch1, tgu_ch2, tgu_ch3, tsense_pwm1, tsense_pwm2,
+		    tsif1_clk, tsif1_data, tsif1_en, tsif1_error, tsif1_sync,
+		    tsif2_clk, tsif2_data, tsif2_en, tsif2_error, tsif2_sync,
+		    uim1_clk, uim1_data, uim1_present, uim1_reset, uim2_clk,
+		    uim2_data, uim2_present, uim2_reset, uim_batt, usb_phy,
+		    vfr_1, vsense_trigger, wlan1_adc0, wlan1_adc1, wlan2_adc0,
+		    wlan2_adc1,
+
+- bias-disable:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as no pull.
+
+- bias-pull-down:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as pull down.
+
+- bias-pull-up:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as pull up.
+
+- output-high:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    high.
+		    Not valid for sdc pins.
+
+- output-low:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    low.
+		    Not valid for sdc pins.
+
+- drive-strength:
+	Usage: optional
+	Value type: <u32>
+	Definition: Selects the drive strength for the specified pins, in mA.
+		    Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
+
+Example:
+
+	tlmm: pinctrl@3400000 {
+		compatible = "qcom,sdm845-pinctrl";
+		reg = <0x03400000 0xc00000>;
+		interrupts = <GIC_SPI 208 0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		qup9_active: qup9-active {
+			mux {
+				pins = "gpio4", "gpio5";
+				function = "qup9";
+			};
+
+			config {
+				pins = "gpio4", "gpio5";
+				drive-strength = <2>;
+				bias-disable;
+			};
+		};
+	};

Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt

@@ -15,7 +15,7 @@ Required Properties:
     - "renesas,pfc-r8a7740": for R8A7740 (R-Mobile A1) compatible pin-controller.
     - "renesas,pfc-r8a7743": for R8A7743 (RZ/G1M) compatible pin-controller.
     - "renesas,pfc-r8a7745": for R8A7745 (RZ/G1E) compatible pin-controller.
-    - "renesas,pfc-r8a7778": for R8A7778 (R-Mobile M1) compatible pin-controller.
+    - "renesas,pfc-r8a7778": for R8A7778 (R-Car M1) compatible pin-controller.
     - "renesas,pfc-r8a7779": for R8A7779 (R-Car H1) compatible pin-controller.
     - "renesas,pfc-r8a7790": for R8A7790 (R-Car H2) compatible pin-controller.
     - "renesas,pfc-r8a7791": for R8A7791 (R-Car M2-W) compatible pin-controller.
@@ -24,7 +24,9 @@ Required Properties:
     - "renesas,pfc-r8a7794": for R8A7794 (R-Car E2) compatible pin-controller.
     - "renesas,pfc-r8a7795": for R8A7795 (R-Car H3) compatible pin-controller.
     - "renesas,pfc-r8a7796": for R8A7796 (R-Car M3-W) compatible pin-controller.
+    - "renesas,pfc-r8a77965": for R8A77965 (R-Car M3-N) compatible pin-controller.
     - "renesas,pfc-r8a77970": for R8A77970 (R-Car V3M) compatible pin-controller.
+    - "renesas,pfc-r8a77980": for R8A77980 (R-Car V3H) compatible pin-controller.
     - "renesas,pfc-r8a77995": for R8A77995 (R-Car D3) compatible pin-controller.
     - "renesas,pfc-sh73a0": for SH73A0 (SH-Mobile AG5) compatible pin-controller.
 

drivers/pinctrl/Kconfig

@@ -244,18 +244,6 @@ config PINCTRL_ST
 	select PINCONF
 	select GPIOLIB_IRQCHIP
 
-config PINCTRL_TZ1090
-	bool "Toumaz Xenif TZ1090 pin control driver"
-	depends on SOC_TZ1090
-	select PINMUX
-	select GENERIC_PINCONF
-
-config PINCTRL_TZ1090_PDC
-	bool "Toumaz Xenif TZ1090 PDC pin control driver"
-	depends on SOC_TZ1090
-	select PINMUX
-	select PINCONF
-
 config PINCTRL_U300
 	bool "U300 pin controller driver"
 	depends on ARCH_U300

drivers/pinctrl/Makefile

@@ -31,8 +31,6 @@ obj-$(CONFIG_PINCTRL_SINGLE)	+= pinctrl-single.o
 obj-$(CONFIG_PINCTRL_SIRF)	+= sirf/
 obj-$(CONFIG_PINCTRL_SX150X)	+= pinctrl-sx150x.o
 obj-$(CONFIG_ARCH_TEGRA)	+= tegra/
-obj-$(CONFIG_PINCTRL_TZ1090)	+= pinctrl-tz1090.o
-obj-$(CONFIG_PINCTRL_TZ1090_PDC)	+= pinctrl-tz1090-pdc.o
 obj-$(CONFIG_PINCTRL_U300)	+= pinctrl-u300.o
 obj-$(CONFIG_PINCTRL_COH901)	+= pinctrl-coh901.o
 obj-$(CONFIG_PINCTRL_XWAY)	+= pinctrl-xway.o

drivers/pinctrl/core.c

@@ -1416,6 +1416,7 @@ int pinctrl_register_mappings(const struct pinctrl_map *maps,
 {
 	return pinctrl_register_map(maps, num_maps, true);
 }
+EXPORT_SYMBOL_GPL(pinctrl_register_mappings);
 
 void pinctrl_unregister_map(const struct pinctrl_map *map)
 {
@@ -1586,6 +1587,7 @@ static int pinctrl_pins_show(struct seq_file *s, void *what)
 
 	return 0;
 }
+DEFINE_SHOW_ATTRIBUTE(pinctrl_pins);
 
 static int pinctrl_groups_show(struct seq_file *s, void *what)
 {
@@ -1631,6 +1633,7 @@ static int pinctrl_groups_show(struct seq_file *s, void *what)
 
 	return 0;
 }
+DEFINE_SHOW_ATTRIBUTE(pinctrl_groups);
 
 static int pinctrl_gpioranges_show(struct seq_file *s, void *what)
 {
@@ -1664,6 +1667,7 @@ static int pinctrl_gpioranges_show(struct seq_file *s, void *what)
 
 	return 0;
 }
+DEFINE_SHOW_ATTRIBUTE(pinctrl_gpioranges);
 
 static int pinctrl_devices_show(struct seq_file *s, void *what)
 {
@@ -1690,6 +1694,7 @@ static int pinctrl_devices_show(struct seq_file *s, void *what)
 
 	return 0;
 }
+DEFINE_SHOW_ATTRIBUTE(pinctrl_devices);
 
 static inline const char *map_type(enum pinctrl_map_type type)
 {
@@ -1743,6 +1748,7 @@ static int pinctrl_maps_show(struct seq_file *s, void *what)
 
 	return 0;
 }
+DEFINE_SHOW_ATTRIBUTE(pinctrl_maps);
 
 static int pinctrl_show(struct seq_file *s, void *what)
 {
@@ -1788,87 +1794,30 @@ static int pinctrl_show(struct seq_file *s, void *what)
 
 	return 0;
 }
-
-static int pinctrl_pins_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, pinctrl_pins_show, inode->i_private);
-}
-
-static int pinctrl_groups_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, pinctrl_groups_show, inode->i_private);
-}
-
-static int pinctrl_gpioranges_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, pinctrl_gpioranges_show, inode->i_private);
-}
-
-static int pinctrl_devices_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, pinctrl_devices_show, NULL);
-}
-
-static int pinctrl_maps_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, pinctrl_maps_show, NULL);
-}
-
-static int pinctrl_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, pinctrl_show, NULL);
-}
-
-static const struct file_operations pinctrl_pins_ops = {
-	.open		= pinctrl_pins_open,
-	.read		= seq_read,
-	.llseek		= seq_lseek,
-	.release	= single_release,
-};
-
-static const struct file_operations pinctrl_groups_ops = {
-	.open		= pinctrl_groups_open,
-	.read		= seq_read,
-	.llseek		= seq_lseek,
-	.release	= single_release,
-};
-
-static const struct file_operations pinctrl_gpioranges_ops = {
-	.open		= pinctrl_gpioranges_open,
-	.read		= seq_read,
-	.llseek		= seq_lseek,
-	.release	= single_release,
-};
-
-static const struct file_operations pinctrl_devices_ops = {
-	.open		= pinctrl_devices_open,
-	.read		= seq_read,
-	.llseek		= seq_lseek,
-	.release	= single_release,
-};
-
-static const struct file_operations pinctrl_maps_ops = {
-	.open		= pinctrl_maps_open,
-	.read		= seq_read,
-	.llseek		= seq_lseek,
-	.release	= single_release,
-};
-
-static const struct file_operations pinctrl_ops = {
-	.open		= pinctrl_open,
-	.read		= seq_read,
-	.llseek		= seq_lseek,
-	.release	= single_release,
-};
+DEFINE_SHOW_ATTRIBUTE(pinctrl);
 
 static struct dentry *debugfs_root;
 
 static void pinctrl_init_device_debugfs(struct pinctrl_dev *pctldev)
 {
 	struct dentry *device_root;
+	const char *debugfs_name;
+
+	if (pctldev->desc->name &&
+			strcmp(dev_name(pctldev->dev), pctldev->desc->name)) {
+		debugfs_name = devm_kasprintf(pctldev->dev, GFP_KERNEL,
+				"%s-%s", dev_name(pctldev->dev),
+				pctldev->desc->name);
+		if (!debugfs_name) {
+			pr_warn("failed to determine debugfs dir name for %s\n",
+				dev_name(pctldev->dev));
+			return;
+		}
+	} else {
+		debugfs_name = dev_name(pctldev->dev);
+	}
 
-	device_root = debugfs_create_dir(dev_name(pctldev->dev),
-					 debugfs_root);
+	device_root = debugfs_create_dir(debugfs_name, debugfs_root);
 	pctldev->device_root = device_root;
 
 	if (IS_ERR(device_root) || !device_root) {
@@ -1877,11 +1826,11 @@ static void pinctrl_init_device_debugfs(struct pinctrl_dev *pctldev)
 		return;
 	}
 	debugfs_create_file("pins", S_IFREG | S_IRUGO,
-			    device_root, pctldev, &pinctrl_pins_ops);
+			    device_root, pctldev, &pinctrl_pins_fops);
 	debugfs_create_file("pingroups", S_IFREG | S_IRUGO,
-			    device_root, pctldev, &pinctrl_groups_ops);
+			    device_root, pctldev, &pinctrl_groups_fops);
 	debugfs_create_file("gpio-ranges", S_IFREG | S_IRUGO,
-			    device_root, pctldev, &pinctrl_gpioranges_ops);
+			    device_root, pctldev, &pinctrl_gpioranges_fops);
 	if (pctldev->desc->pmxops)
 		pinmux_init_device_debugfs(device_root, pctldev);
 	if (pctldev->desc->confops)
@@ -1903,11 +1852,11 @@ static void pinctrl_init_debugfs(void)
 	}
 
 	debugfs_create_file("pinctrl-devices", S_IFREG | S_IRUGO,
-			    debugfs_root, NULL, &pinctrl_devices_ops);
+			    debugfs_root, NULL, &pinctrl_devices_fops);
 	debugfs_create_file("pinctrl-maps", S_IFREG | S_IRUGO,
-			    debugfs_root, NULL, &pinctrl_maps_ops);
+			    debugfs_root, NULL, &pinctrl_maps_fops);
 	debugfs_create_file("pinctrl-handles", S_IFREG | S_IRUGO,
-			    debugfs_root, NULL, &pinctrl_ops);
+			    debugfs_root, NULL, &pinctrl_fops);
 }
 
 #else /* CONFIG_DEBUG_FS */

drivers/pinctrl/devicetree.c

@@ -122,7 +122,9 @@ static int dt_to_map_one_config(struct pinctrl *p,
 			/* OK let's just assume this will appear later then */
 			return -EPROBE_DEFER;
 		}
-		if (!pctldev)
+		/* If we're creating a hog we can use the passed pctldev */
+		if (pctldev && (np_pctldev == p->dev->of_node))
+			break;
 		pctldev = get_pinctrl_dev_from_of_node(np_pctldev);
 		if (pctldev)
 			break;

drivers/pinctrl/freescale/Kconfig

@@ -82,6 +82,13 @@ config PINCTRL_IMX6SL
 	help
 	  Say Y here to enable the imx6sl pinctrl driver
 
+config PINCTRL_IMX6SLL
+	bool "IMX6SLL pinctrl driver"
+	depends on SOC_IMX6SLL
+	select PINCTRL_IMX
+	help
+	  Say Y here to enable the imx6sll pinctrl driver
+
 config PINCTRL_IMX6SX
 	bool "IMX6SX pinctrl driver"
 	depends on SOC_IMX6SX

drivers/pinctrl/freescale/Makefile

@@ -12,6 +12,7 @@ obj-$(CONFIG_PINCTRL_IMX53)	+= pinctrl-imx53.o
 obj-$(CONFIG_PINCTRL_IMX6Q)	+= pinctrl-imx6q.o
 obj-$(CONFIG_PINCTRL_IMX6Q)	+= pinctrl-imx6dl.o
 obj-$(CONFIG_PINCTRL_IMX6SL)	+= pinctrl-imx6sl.o
+obj-$(CONFIG_PINCTRL_IMX6SLL)	+= pinctrl-imx6sll.o
 obj-$(CONFIG_PINCTRL_IMX6SX)	+= pinctrl-imx6sx.o
 obj-$(CONFIG_PINCTRL_IMX6UL)	+= pinctrl-imx6ul.o
 obj-$(CONFIG_PINCTRL_IMX7D)	+= pinctrl-imx7d.o

drivers/pinctrl/intel/pinctrl-intel.c

@@ -788,6 +788,24 @@ static void intel_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
 	raw_spin_unlock_irqrestore(&pctrl->lock, flags);
 }
 
+static int intel_gpio_get_direction(struct gpio_chip *chip, unsigned int offset)
+{
+	struct intel_pinctrl *pctrl = gpiochip_get_data(chip);
+	void __iomem *reg;
+	u32 padcfg0;
+
+	reg = intel_get_padcfg(pctrl, offset, PADCFG0);
+	if (!reg)
+		return -EINVAL;
+
+	padcfg0 = readl(reg);
+
+	if (padcfg0 & PADCFG0_PMODE_MASK)
+		return -EINVAL;
+
+	return !!(padcfg0 & PADCFG0_GPIOTXDIS);
+}
+
 static int intel_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
 {
 	return pinctrl_gpio_direction_input(chip->base + offset);
@@ -804,6 +822,7 @@ static const struct gpio_chip intel_gpio_chip = {
 	.owner = THIS_MODULE,
 	.request = gpiochip_generic_request,
 	.free = gpiochip_generic_free,
+	.get_direction = intel_gpio_get_direction,
 	.direction_input = intel_gpio_direction_input,
 	.direction_output = intel_gpio_direction_output,
 	.get = intel_gpio_get,

drivers/pinctrl/mediatek/Kconfig

@@ -32,6 +32,13 @@ config PINCTRL_MT8127
 	select PINCTRL_MTK
 
 # For ARMv8 SoCs
+config PINCTRL_MT2712
+	bool "MediaTek MT2712 pin control"
+	depends on OF
+	depends on ARM64 || COMPILE_TEST
+	default ARM64 && ARCH_MEDIATEK
+	select PINCTRL_MTK
+
 config PINCTRL_MT7622
 	bool "MediaTek MT7622 pin control"
 	depends on OF

drivers/pinctrl/mediatek/Makefile

@@ -4,6 +4,7 @@ obj-$(CONFIG_PINCTRL_MTK)	+= pinctrl-mtk-common.o
 
 # SoC Drivers
 obj-$(CONFIG_PINCTRL_MT2701)	+= pinctrl-mt2701.o
+obj-$(CONFIG_PINCTRL_MT2712)	+= pinctrl-mt2712.o
 obj-$(CONFIG_PINCTRL_MT8135)	+= pinctrl-mt8135.o
 obj-$(CONFIG_PINCTRL_MT8127)	+= pinctrl-mt8127.o
 obj-$(CONFIG_PINCTRL_MT7622)	+= pinctrl-mt7622.o

drivers/pinctrl/mediatek/pinctrl-mtk-common.c

@@ -293,7 +293,7 @@ static int mtk_pconf_set_pull_select(struct mtk_pinctrl *pctl,
 		unsigned int pin, bool enable, bool isup, unsigned int arg)
 {
 	unsigned int bit;
-	unsigned int reg_pullen, reg_pullsel;
+	unsigned int reg_pullen, reg_pullsel, r1r0;
 	int ret;
 
 	/* Some pins' pull setting are very different,
@@ -301,8 +301,12 @@ static int mtk_pconf_set_pull_select(struct mtk_pinctrl *pctl,
 	 * resistor bit, so we need this special handle.
 	 */
 	if (pctl->devdata->spec_pull_set) {
+		/* For special pins, bias-disable is set by R1R0,
+		 * the parameter should be "MTK_PUPD_SET_R1R0_00".
+		 */
+		r1r0 = enable ? arg : MTK_PUPD_SET_R1R0_00;
 		ret = pctl->devdata->spec_pull_set(mtk_get_regmap(pctl, pin),
-			pin, pctl->devdata->port_align, isup, arg);
+			pin, pctl->devdata->port_align, isup, r1r0);
 		if (!ret)
 			return 0;
 	}
@@ -501,7 +505,7 @@ static int mtk_pctrl_dt_subnode_to_map(struct pinctrl_dev *pctldev,
 	int num_pins, num_funcs, maps_per_pin;
 	unsigned long *configs;
 	unsigned int num_configs;
-	bool has_config = 0;
+	bool has_config = false;
 	int i, err;
 	unsigned reserve = 0;
 	struct mtk_pinctrl_group *grp;
@@ -520,7 +524,7 @@ static int mtk_pctrl_dt_subnode_to_map(struct pinctrl_dev *pctldev,
 		return err;
 
 	if (num_configs)
-		has_config = 1;
+		has_config = true;
 
 	num_pins = pins->length / sizeof(u32);
 	num_funcs = num_pins;

drivers/pinctrl/meson/pinctrl-meson8b.c

@@ -885,9 +885,13 @@ static struct meson_pmx_func meson8b_aobus_functions[] = {
 
 static struct meson_bank meson8b_cbus_banks[] = {
 	/*   name        first          last        irq       pullen   pull     dir      out      in   */
-	BANK("X",    GPIOX_0,		GPIOX_21,   97, 118, 4,  0,  4,  0,  0,  0,  1,  0,  2,  0),
-	BANK("Y",    GPIOY_0,		GPIOY_14,   80,  96, 3,  0,  3,  0,  3,  0,  4,  0,  5,  0),
-	BANK("DV",   GPIODV_9,		GPIODV_29,  59,  79, 0,  0,  0,  0,  7,  0,  8,  0,  9,  0),
+	BANK("X0..11",	 GPIOX_0,	GPIOX_11,   97, 108,  4,  0,   4,  0,   0,  0,   1,  0,   2,  0),
+	BANK("X16..21",	 GPIOX_16,	GPIOX_21,  113, 118,  4, 16,   4, 16,   0, 16,   1, 16,   2, 16),
+	BANK("Y0..1",	 GPIOY_0,	GPIOY_1,    80,  81,  3,  0,   3,  0,   3,  0,   4,  0,   5,  0),
+	BANK("Y3",	 GPIOY_3,	GPIOY_3,    83,  83,  3,  3,   3,  3,   3,  3,   4,  3,   5,  3),
+	BANK("Y6..14",	 GPIOY_6,	GPIOY_14,   86,  94,  3,  6,   3,  6,   3,  6,   4,  6,   5,  6),
+	BANK("DV9",	 GPIODV_9,	GPIODV_9,   59,  59,  0,  9,   0,  9,   7,  9,   8,  9,   9,  9),
+	BANK("DV24..29", GPIODV_24,	GPIODV_29,  74,  79,  0, 24,   0, 24,   7, 24,   8, 24,   9, 24),
 	BANK("H",	 GPIOH_0,	GPIOH_9,    14,  23,  1, 16,   1, 16,   9, 19,  10, 19,  11, 19),
 	BANK("CARD",	 CARD_0,	CARD_6,     43,  49,  2, 20,   2, 20,   0, 22,   1, 22,   2, 22),
 	BANK("BOOT",	 BOOT_0,	BOOT_18,    24,  42,  2,  0,   2,  0,   9,  0,  10,  0,  11,  0),

drivers/pinctrl/nomadik/Kconfig

@@ -11,14 +11,6 @@ config PINCTRL_AB8500
 	bool "AB8500 pin controller driver"
 	depends on PINCTRL_ABX500 && ARCH_U8500
 
-config PINCTRL_AB8540
-	bool "AB8540 pin controller driver"
-	depends on PINCTRL_ABX500 && ARCH_U8500
-
-config PINCTRL_AB9540
-	bool "AB9540 pin controller driver"
-	depends on PINCTRL_ABX500 && ARCH_U8500
-
 config PINCTRL_AB8505
 	bool "AB8505 pin controller driver"
 	depends on PINCTRL_ABX500 && ARCH_U8500
@@ -44,8 +36,4 @@ config PINCTRL_DB8500
 	bool "DB8500 pin controller driver"
 	depends on PINCTRL_NOMADIK && ARCH_U8500
 
-config PINCTRL_DB8540
-	bool "DB8540 pin controller driver"
-	depends on PINCTRL_NOMADIK && ARCH_U8500
-
 endif

drivers/pinctrl/nomadik/Makefile

@@ -2,10 +2,7 @@
 # Nomadik family pin control drivers
 obj-$(CONFIG_PINCTRL_ABX500)	+= pinctrl-abx500.o
 obj-$(CONFIG_PINCTRL_AB8500)	+= pinctrl-ab8500.o
-obj-$(CONFIG_PINCTRL_AB8540)	+= pinctrl-ab8540.o
-obj-$(CONFIG_PINCTRL_AB9540)	+= pinctrl-ab9540.o
 obj-$(CONFIG_PINCTRL_AB8505)	+= pinctrl-ab8505.o
 obj-$(CONFIG_PINCTRL_NOMADIK)	+= pinctrl-nomadik.o
 obj-$(CONFIG_PINCTRL_STN8815)	+= pinctrl-nomadik-stn8815.o
 obj-$(CONFIG_PINCTRL_DB8500)	+= pinctrl-nomadik-db8500.o
-obj-$(CONFIG_PINCTRL_DB8540)	+= pinctrl-nomadik-db8540.o

drivers/pinctrl/nomadik/pinctrl-abx500.h

@@ -4,9 +4,7 @@
 
 /* Package definitions */
 #define PINCTRL_AB8500	0
-#define PINCTRL_AB8540	1
-#define PINCTRL_AB9540	2
-#define PINCTRL_AB8505	3
+#define PINCTRL_AB8505	1
 
 /* pins alternate function */
 enum abx500_pin_func {
@@ -96,17 +94,6 @@ struct alternate_functions {
 	u8 altc_val;
 };
 
-/**
- * struct pullud - specific pull up/down feature
- * @first_pin:		The pin number of the first pins which support
- *			specific pull up/down
- * @last_pin:		The pin number of the last pins
- */
-struct pullud {
-	unsigned first_pin;
-	unsigned last_pin;
-};
-
 #define GPIO_IRQ_CLUSTER(a, b, c)	\
 {					\
 	.start = a,			\
@@ -162,8 +149,6 @@ struct abx500_pinrange {
  * @ngroups:		The number of entries in @groups.
  * @alternate_functions: array describing pins which supports alternate and
  *			how to set it.
- * @pullud:		array describing pins which supports pull up/down
- *			specific registers.
  * @gpio_irq_cluster:	An array of GPIO interrupt capable for this SoC
  * @ngpio_irq_cluster:	The number of GPIO inetrrupt capable for this SoC
  * @irq_gpio_rising_offset: Interrupt offset used as base to compute specific
@@ -184,7 +169,6 @@ struct abx500_pinctrl_soc_data {
 	const struct abx500_pingroup *groups;
 	unsigned ngroups;
 	struct alternate_functions *alternate_functions;
-	struct pullud *pullud;
 	struct abx500_gpio_irq_cluster *gpio_irq_cluster;
 	unsigned ngpio_irq_cluster;
 	int irq_gpio_rising_offset;
@@ -205,32 +189,6 @@ abx500_pinctrl_ab8500_init(struct abx500_pinctrl_soc_data **soc)
 
 #endif
 
-#ifdef CONFIG_PINCTRL_AB8540
-
-void abx500_pinctrl_ab8540_init(struct abx500_pinctrl_soc_data **soc);
-
-#else
-
-static inline void
-abx500_pinctrl_ab8540_init(struct abx500_pinctrl_soc_data **soc)
-{
-}
-
-#endif
-
-#ifdef CONFIG_PINCTRL_AB9540
-
-void abx500_pinctrl_ab9540_init(struct abx500_pinctrl_soc_data **soc);
-
-#else
-
-static inline void
-abx500_pinctrl_ab9540_init(struct abx500_pinctrl_soc_data **soc)
-{
-}
-
-#endif
-
 #ifdef CONFIG_PINCTRL_AB8505
 
 void abx500_pinctrl_ab8505_init(struct abx500_pinctrl_soc_data **soc);