Merge remote-tracking branches 'regulator/topic/pv88090',...

Merge remote-tracking branches 'regulator/topic/pv88090', 'regulator/topic/qcom-smd', 'regulator/topic/tps6105x', 'regulator/topic/tps65086' and 'regulator/topic/tps65218' into regulator-next

Documentation/devicetree/bindings/regulator/pv88090.txt

+* Powerventure Semiconductor PV88090 Voltage Regulator
+
+Required properties:
+- compatible: "pvs,pv88090".
+- reg: I2C slave address, usually 0x48.
+- interrupts: the interrupt outputs of the controller
+- regulators: A node that houses a sub-node for each regulator within the
+  device. Each sub-node is identified using the node's name, with valid
+  values listed below. The content of each sub-node is defined by the
+  standard binding for regulators; see regulator.txt.
+  BUCK1, BUCK2, BUCK3, LDO1, and LDO2.
+
+Optional properties:
+- Any optional property defined in regulator.txt
+
+Example
+
+	pmic: pv88090@48 {
+		compatible = "pvs,pv88090";
+		reg = <0x48>;
+		interrupt-parent = <&gpio>;
+		interrupts = <24 24>;
+
+		regulators {
+			BUCK1 {
+				regulator-name = "buck1";
+				regulator-min-microvolt = < 600000>;
+				regulator-max-microvolt = <1393750>;
+				regulator-min-microamp 	= < 220000>;
+				regulator-max-microamp 	= <7040000>;
+				regulator-boot-on;
+			};
+
+			BUCK2 {
+				regulator-name = "buck2";
+				regulator-min-microvolt = < 600000>;
+				regulator-max-microvolt = <1393750>;
+				regulator-min-microamp 	= <1496000>;
+				regulator-max-microamp 	= <4189000>;
+			};
+
+			BUCK3 {
+				regulator-name = "buck3";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <1393750>;
+				regulator-min-microamp 	= <1496000>;
+				regulator-max-microamp 	= <4189000>;
+				regulator-boot-on;
+			};
+
+			LDO1 {
+				regulator-name = "ldo1";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <4350000>;
+				regulator-boot-on;
+			};
+
+			LDO2 {
+				regulator-name = "ldo2";
+				regulator-min-microvolt = < 650000>;
+				regulator-max-microvolt = <2225000>;
+				regulator-boot-on;
+			};
+		};
+	};

Documentation/devicetree/bindings/soc/qcom,smd-rpm.txt → Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt

-Qualcomm Resource Power Manager (RPM) over SMD
+QCOM SMD RPM REGULATOR
 
-This driver is used to interface with the Resource Power Manager (RPM) found in
-various Qualcomm platforms. The RPM allows each component in the system to vote
-for state of the system resources, such as clocks, regulators and bus
-frequencies.
+The Qualcomm RPM over SMD regulator is modelled as a subdevice of the RPM.
+Because SMD is used as the communication transport mechanism, the RPM resides as
+a subnode of the SMD.  As such, the SMD-RPM regulator requires that the SMD and
+RPM nodes be present.
 
-- compatible:
-	Usage: required
-	Value type: <string>
-	Definition: must be one of:
-		    "qcom,rpm-msm8974"
+Please refer to Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt for
+information pertaining to the SMD node.
 
-- qcom,smd-channels:
-	Usage: required
-	Value type: <stringlist>
-	Definition: Shared Memory channel used for communication with the RPM
+Please refer to Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt for
+information regarding the RPM node.
 
-= SUBDEVICES
-
-The RPM exposes resources to its subnodes. The below bindings specify the set
-of valid subnodes that can operate on these resources.
-
-== Regulators
+== Regulator
 
 Regulator nodes are identified by their compatible:
 
@@ -30,7 +20,9 @@ Regulator nodes are identified by their compatible:
 	Value type: <string>
 	Definition: must be one of:
 		    "qcom,rpm-pm8841-regulators"
+		    "qcom,rpm-pm8916-regulators"
 		    "qcom,rpm-pm8941-regulators"
+		    "qcom,rpm-pma8084-regulators"
 
 - vdd_s1-supply:
 - vdd_s2-supply:
@@ -45,6 +37,19 @@ Regulator nodes are identified by their compatible:
 	Definition: reference to regulator supplying the input pin, as
 		    described in the data sheet
 
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s3-supply:
+- vdd_s4-supply:
+- vdd_l1_l2_l3-supply:
+- vdd_l4_l5_l6-supply:
+- vdd_l7-supply:
+- vdd_l8_l9_l10_l11_l12_l13_l14_l15_l16_l17_l18-supply:
+	Usage: optional (pm8916 only)
+	Value type: <phandle>
+	Definition: reference to regulator supplying the input pin, as
+		    described in the data sheet
+
 - vdd_s1-supply:
 - vdd_s2-supply:
 - vdd_s3-supply:
@@ -63,6 +68,35 @@ Regulator nodes are identified by their compatible:
 	Definition: reference to regulator supplying the input pin, as
 		    described in the data sheet
 
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s3-supply:
+- vdd_s4-supply:
+- vdd_s5-supply:
+- vdd_s6-supply:
+- vdd_s7-supply:
+- vdd_s8-supply:
+- vdd_s9-supply:
+- vdd_s10-supply:
+- vdd_s11-supply:
+- vdd_s12-supply:
+- vdd_l1_l11-supply:
+- vdd_l2_l3_l4_l27-supply:
+- vdd_l5_l7-supply:
+- vdd_l6_l12_l14_l15_l26-supply:
+- vdd_l8-supply:
+- vdd_l9_l10_l13_l20_l23_l24-supply:
+- vdd_l16_l25-supply:
+- vdd_l17-supply:
+- vdd_l18-supply:
+- vdd_l19-supply:
+- vdd_l21-supply:
+- vdd_l22-supply:
+	Usage: optional (pma8084 only)
+	Value type: <phandle>
+	Definition: reference to regulator supplying the input pin, as
+		    described in the data sheet
+
 The regulator node houses sub-nodes for each regulator within the device. Each
 sub-node is identified using the node's name, with valid values listed for each
 of the pmics below.
@@ -70,11 +104,20 @@ of the pmics below.
 pm8841:
 	s1, s2, s3, s4, s5, s6, s7, s8
 
+pm8916:
+	s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
+	l14, l15, l16, l17, l18
+
 pm8941:
 	s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
 	l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2,
 	lvs3, 5vs1, 5vs2
 
+pma8084:
+	s1, s2, s3, s4, s5, s6, s7, s8, s9, s10, s11, s12, l1, l2, l3, l4, l5,
+	l6, l7, l8, l9, l10, l11, l12, l13, l14, l15, l16, l17, l18, l19, l20,
+	l21, l22, l23, l24, l25, l26, l27, lvs1, lvs2, lvs3, lvs4, 5vs1
+
 The content of each sub-node is defined by the standard binding for regulators -
 see regulator.txt.
 
@@ -114,4 +157,3 @@ see regulator.txt.
 			};
 		};
 	};
-

Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt

+Qualcomm Resource Power Manager (RPM) over SMD
+
+This driver is used to interface with the Resource Power Manager (RPM) found in
+various Qualcomm platforms. The RPM allows each component in the system to vote
+for state of the system resources, such as clocks, regulators and bus
+frequencies.
+
+The SMD information for the RPM edge should be filled out.  See qcom,smd.txt for
+the required edge properties.  All SMD related properties will reside within the
+RPM node itself.
+
+= SUBDEVICES
+
+The RPM exposes resources to its subnodes.  The rpm_requests node must be
+present and this subnode may contain children that designate regulator
+resources.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be one of:
+		    "qcom,rpm-apq8084"
+		    "qcom,rpm-msm8916"
+		    "qcom,rpm-msm8974"
+
+- qcom,smd-channels:
+	Usage: required
+	Value type: <string>
+	Definition: must be "rpm_requests"
+
+Refer to Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt
+for information on the regulator subnodes that can exist under the rpm_requests.
+
+Example:
+
+	soc {
+		apcs: syscon@f9011000 {
+			compatible = "syscon";
+			reg = <0xf9011000 0x1000>;
+		};
+	};
+
+	smd {
+		compatible = "qcom,smd";
+
+		rpm {
+			interrupts = <0 168 1>;
+			qcom,ipc = <&apcs 8 0>;
+			qcom,smd-edge = <15>;
+
+			rpm_requests {
+				compatible = "qcom,rpm-msm8974";
+				qcom,smd-channels = "rpm_requests";
+
+				...
+			};
+		};
+	};

drivers/regulator/Kconfig

@@ -522,6 +522,14 @@ config REGULATOR_PV88060
 	  Say y here to support the voltage regulators and convertors
 	  PV88060
 
+config REGULATOR_PV88090
+	tristate "Powerventure Semiconductor PV88090 regulator"
+	depends on I2C
+	select REGMAP_I2C
+	help
+	  Say y here to support the voltage regulators and convertors
+	  on PV88090
+
 config REGULATOR_PWM
 	tristate "PWM voltage regulator"
 	depends on PWM
@@ -698,6 +706,13 @@ config REGULATOR_TPS6507X
 	  three step-down converters and two general-purpose LDO voltage regulators.
 	  It supports TI's software based Class-2 SmartReflex implementation.
 
+config REGULATOR_TPS65086
+	tristate "TI TPS65086 Power regulators"
+	depends on MFD_TPS65086
+	help
+	  This driver provides support for the voltage regulators on
+	  TI TPS65086 PMICs.
+
 config REGULATOR_TPS65090
 	tristate "TI TPS65090 Power regulator"
 	depends on MFD_TPS65090

drivers/regulator/Makefile

@@ -68,6 +68,7 @@ obj-$(CONFIG_REGULATOR_QCOM_SPMI) += qcom_spmi-regulator.o
 obj-$(CONFIG_REGULATOR_PALMAS) += palmas-regulator.o
 obj-$(CONFIG_REGULATOR_PFUZE100) += pfuze100-regulator.o
 obj-$(CONFIG_REGULATOR_PV88060) += pv88060-regulator.o
+obj-$(CONFIG_REGULATOR_PV88090) += pv88090-regulator.o
 obj-$(CONFIG_REGULATOR_PWM) += pwm-regulator.o
 obj-$(CONFIG_REGULATOR_TPS51632) += tps51632-regulator.o
 obj-$(CONFIG_REGULATOR_PBIAS) += pbias-regulator.o
@@ -87,6 +88,7 @@ obj-$(CONFIG_REGULATOR_TPS6105X) += tps6105x-regulator.o
 obj-$(CONFIG_REGULATOR_TPS62360) += tps62360-regulator.o
 obj-$(CONFIG_REGULATOR_TPS65023) += tps65023-regulator.o
 obj-$(CONFIG_REGULATOR_TPS6507X) += tps6507x-regulator.o
+obj-$(CONFIG_REGULATOR_TPS65086) += tps65086-regulator.o
 obj-$(CONFIG_REGULATOR_TPS65090) += tps65090-regulator.o
 obj-$(CONFIG_REGULATOR_TPS65217) += tps65217-regulator.o
 obj-$(CONFIG_REGULATOR_TPS65218) += tps65218-regulator.o

drivers/regulator/pv88090-regulator.c

+/*
+ * pv88090-regulator.c - Regulator device driver for PV88090
+ * Copyright (C) 2015  Powerventure Semiconductor Ltd.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regmap.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/proc_fs.h>
+#include <linux/uaccess.h>
+#include "pv88090-regulator.h"
+
+#define PV88090_MAX_REGULATORS	5
+
+/* PV88090 REGULATOR IDs */
+enum {
+	/* BUCKs */
+	PV88090_ID_BUCK1,
+	PV88090_ID_BUCK2,
+	PV88090_ID_BUCK3,
+
+	/* LDOs */
+	PV88090_ID_LDO1,
+	PV88090_ID_LDO2,
+};
+
+struct pv88090_regulator {
+	struct regulator_desc desc;
+	/* Current limiting */
+	unsigned	n_current_limits;
+	const int	*current_limits;
+	unsigned int limit_mask;
+	unsigned int conf;
+	unsigned int conf2;
+};
+
+struct pv88090 {
+	struct device *dev;
+	struct regmap *regmap;
+	struct regulator_dev *rdev[PV88090_MAX_REGULATORS];
+};
+
+struct pv88090_buck_voltage {
+	int min_uV;
+	int max_uV;
+	int uV_step;
+};
+
+static const struct regmap_config pv88090_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+};
+
+/* Current limits array (in uA) for BUCK1, BUCK2, BUCK3.
+ *  Entry indexes corresponds to register values.
+ */
+
+static const int pv88090_buck1_limits[] = {
+	 220000,  440000,  660000,  880000, 1100000, 1320000, 1540000, 1760000,
+	1980000, 2200000, 2420000, 2640000, 2860000, 3080000, 3300000, 3520000,
+	3740000, 3960000, 4180000, 4400000, 4620000, 4840000, 5060000, 5280000,
+	5500000, 5720000, 5940000, 6160000, 6380000, 6600000, 6820000, 7040000
+};
+
+static const int pv88090_buck23_limits[] = {
+	1496000, 2393000, 3291000, 4189000
+};
+
+static const struct pv88090_buck_voltage pv88090_buck_vol[3] = {
+	{
+		.min_uV = 600000,
+		.max_uV = 1393750,
+		.uV_step = 6250,
+	},
+
+	{
+		.min_uV = 1400000,
+		.max_uV = 2193750,
+		.uV_step = 6250,
+	},
+	{
+		.min_uV = 1250000,
+		.max_uV = 2837500,
+		.uV_step = 12500,
+	},
+};
+
+static unsigned int pv88090_buck_get_mode(struct regulator_dev *rdev)
+{
+	struct pv88090_regulator *info = rdev_get_drvdata(rdev);
+	unsigned int data;
+	int ret, mode = 0;
+
+	ret = regmap_read(rdev->regmap, info->conf, &data);
+	if (ret < 0)
+		return ret;
+
+	switch (data & PV88090_BUCK1_MODE_MASK) {
+	case PV88090_BUCK_MODE_SYNC:
+		mode = REGULATOR_MODE_FAST;
+		break;
+	case PV88090_BUCK_MODE_AUTO:
+		mode = REGULATOR_MODE_NORMAL;
+		break;
+	case PV88090_BUCK_MODE_SLEEP:
+		mode = REGULATOR_MODE_STANDBY;
+		break;
+	}
+
+	return mode;
+}
+
+static int pv88090_buck_set_mode(struct regulator_dev *rdev,
+					unsigned int mode)
+{
+	struct pv88090_regulator *info = rdev_get_drvdata(rdev);
+	int val = 0;
+
+	switch (mode) {
+	case REGULATOR_MODE_FAST:
+		val = PV88090_BUCK_MODE_SYNC;
+		break;
+	case REGULATOR_MODE_NORMAL:
+		val = PV88090_BUCK_MODE_AUTO;
+		break;
+	case REGULATOR_MODE_STANDBY:
+		val = PV88090_BUCK_MODE_SLEEP;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return regmap_update_bits(rdev->regmap, info->conf,
+					PV88090_BUCK1_MODE_MASK, val);
+}
+
+static int pv88090_set_current_limit(struct regulator_dev *rdev, int min,
+				    int max)
+{
+	struct pv88090_regulator *info = rdev_get_drvdata(rdev);
+	int i;
+
+	/* search for closest to maximum */
+	for (i = info->n_current_limits; i >= 0; i--) {
+		if (min <= info->current_limits[i]
+			&& max >= info->current_limits[i]) {
+			return regmap_update_bits(rdev->regmap,
+				info->conf,
+				info->limit_mask,
+				i << PV88090_BUCK1_ILIM_SHIFT);
+		}
+	}
+
+	return -EINVAL;
+}
+
+static int pv88090_get_current_limit(struct regulator_dev *rdev)
+{
+	struct pv88090_regulator *info = rdev_get_drvdata(rdev);
+	unsigned int data;
+	int ret;
+
+	ret = regmap_read(rdev->regmap, info->conf, &data);
+	if (ret < 0)
+		return ret;
+
+	data = (data & info->limit_mask) >> PV88090_BUCK1_ILIM_SHIFT;
+	return info->current_limits[data];
+}
+
+static struct regulator_ops pv88090_buck_ops = {
+	.get_mode = pv88090_buck_get_mode,
+	.set_mode = pv88090_buck_set_mode,
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.list_voltage = regulator_list_voltage_linear,
+	.set_current_limit = pv88090_set_current_limit,
+	.get_current_limit = pv88090_get_current_limit,
+};
+
+static struct regulator_ops pv88090_ldo_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.list_voltage = regulator_list_voltage_linear,
+};
+
+#define PV88090_BUCK(chip, regl_name, min, step, max, limits_array) \
+{\
+	.desc	=	{\
+		.id = chip##_ID_##regl_name,\
+		.name = __stringify(chip##_##regl_name),\
+		.of_match = of_match_ptr(#regl_name),\
+		.regulators_node = of_match_ptr("regulators"),\
+		.type = REGULATOR_VOLTAGE,\
+		.owner = THIS_MODULE,\
+		.ops = &pv88090_buck_ops,\
+		.min_uV = min, \
+		.uV_step = step, \
+		.n_voltages = ((max) - (min))/(step) + 1, \
+		.enable_reg = PV88090_REG_##regl_name##_CONF0, \
+		.enable_mask = PV88090_##regl_name##_EN, \
+		.vsel_reg = PV88090_REG_##regl_name##_CONF0, \
+		.vsel_mask = PV88090_V##regl_name##_MASK, \
+	},\
+	.current_limits = limits_array, \
+	.n_current_limits = ARRAY_SIZE(limits_array), \
+	.limit_mask = PV88090_##regl_name##_ILIM_MASK, \
+	.conf = PV88090_REG_##regl_name##_CONF1, \
+	.conf2 = PV88090_REG_##regl_name##_CONF2, \
+}
+
+#define PV88090_LDO(chip, regl_name, min, step, max) \
+{\
+	.desc	=	{\
+		.id = chip##_ID_##regl_name,\
+		.name = __stringify(chip##_##regl_name),\
+		.of_match = of_match_ptr(#regl_name),\
+		.regulators_node = of_match_ptr("regulators"),\
+		.type = REGULATOR_VOLTAGE,\
+		.owner = THIS_MODULE,\
+		.ops = &pv88090_ldo_ops,\
+		.min_uV = min, \
+		.uV_step = step, \
+		.n_voltages = ((max) - (min))/(step) + 1, \
+		.enable_reg = PV88090_REG_##regl_name##_CONT, \
+		.enable_mask = PV88090_##regl_name##_EN, \
+		.vsel_reg = PV88090_REG_##regl_name##_CONT, \
+		.vsel_mask = PV88090_V##regl_name##_MASK, \
+	},\
+}
+
+static struct pv88090_regulator pv88090_regulator_info[] = {
+	PV88090_BUCK(PV88090, BUCK1, 600000, 6250, 1393750,
+		pv88090_buck1_limits),
+	PV88090_BUCK(PV88090, BUCK2, 600000, 6250, 1393750,
+		pv88090_buck23_limits),
+	PV88090_BUCK(PV88090, BUCK3, 600000, 6250, 1393750,
+		pv88090_buck23_limits),
+	PV88090_LDO(PV88090, LDO1, 1200000, 50000, 4350000),
+	PV88090_LDO(PV88090, LDO2,  650000, 25000, 2225000),
+};
+
+static irqreturn_t pv88090_irq_handler(int irq, void *data)
+{
+	struct pv88090 *chip = data;
+	int i, reg_val, err, ret = IRQ_NONE;
+
+	err = regmap_read(chip->regmap, PV88090_REG_EVENT_A, &reg_val);
+	if (err < 0)
+		goto error_i2c;
+
+	if (reg_val & PV88090_E_VDD_FLT) {
+		for (i = 0; i < PV88090_MAX_REGULATORS; i++) {
+			if (chip->rdev[i] != NULL) {
+				regulator_notifier_call_chain(chip->rdev[i],
+					REGULATOR_EVENT_UNDER_VOLTAGE,
+					NULL);
+			}
+		}
+
+		err = regmap_update_bits(chip->regmap, PV88090_REG_EVENT_A,
+			PV88090_E_VDD_FLT, PV88090_E_VDD_FLT);
+		if (err < 0)
+			goto error_i2c;
+
+		ret = IRQ_HANDLED;
+	}
+
+	if (reg_val & PV88090_E_OVER_TEMP) {
+		for (i = 0; i < PV88090_MAX_REGULATORS; i++) {
+			if (chip->rdev[i] != NULL) {
+				regulator_notifier_call_chain(chip->rdev[i],
+					REGULATOR_EVENT_OVER_TEMP,
+					NULL);
+			}
+		}
+
+		err = regmap_update_bits(chip->regmap, PV88090_REG_EVENT_A,
+			PV88090_E_OVER_TEMP, PV88090_E_OVER_TEMP);
+		if (err < 0)
+			goto error_i2c;
+
+		ret = IRQ_HANDLED;
+	}
+
+	return ret;
+
+error_i2c:
+	dev_err(chip->dev, "I2C error : %d\n", err);
+	return IRQ_NONE;
+}
+
+/*
+ * I2C driver interface functions
+ */
+static int pv88090_i2c_probe(struct i2c_client *i2c,
+		const struct i2c_device_id *id)
+{
+	struct regulator_init_data *init_data = dev_get_platdata(&i2c->dev);
+	struct pv88090 *chip;
+	struct regulator_config config = { };
+	int error, i, ret = 0;
+	unsigned int conf2, range, index;
+
+	chip = devm_kzalloc(&i2c->dev, sizeof(struct pv88090), GFP_KERNEL);
+	if (!chip)
+		return -ENOMEM;
+
+	chip->dev = &i2c->dev;
+	chip->regmap = devm_regmap_init_i2c(i2c, &pv88090_regmap_config);
+	if (IS_ERR(chip->regmap)) {
+		error = PTR_ERR(chip->regmap);
+		dev_err(chip->dev, "Failed to allocate register map: %d\n",
+			error);
+		return error;
+	}
+
+	i2c_set_clientdata(i2c, chip);
+
+	if (i2c->irq != 0) {
+		ret = regmap_write(chip->regmap, PV88090_REG_MASK_A, 0xFF);
+		if (ret < 0) {
+			dev_err(chip->dev,
+				"Failed to mask A reg: %d\n", ret);
+			return ret;
+		}
+
+		ret = regmap_write(chip->regmap, PV88090_REG_MASK_B, 0xFF);
+		if (ret < 0) {
+			dev_err(chip->dev,
+				"Failed to mask B reg: %d\n", ret);
+			return ret;
+		}
+
+		ret = devm_request_threaded_irq(&i2c->dev, i2c->irq, NULL,
+					pv88090_irq_handler,
+					IRQF_TRIGGER_LOW|IRQF_ONESHOT,
+					"pv88090", chip);
+		if (ret != 0) {
+			dev_err(chip->dev, "Failed to request IRQ: %d\n",
+				i2c->irq);
+			return ret;
+		}
+
+		ret = regmap_update_bits(chip->regmap, PV88090_REG_MASK_A,
+			PV88090_M_VDD_FLT | PV88090_M_OVER_TEMP, 0);
+		if (ret < 0) {
+			dev_err(chip->dev,
+				"Failed to update mask reg: %d\n", ret);
+			return ret;
+		}
+
+	} else {
+		dev_warn(chip->dev, "No IRQ configured\n");
+	}
+
+	config.dev = chip->dev;
+	config.regmap = chip->regmap;
+
+	for (i = 0; i < PV88090_MAX_REGULATORS; i++) {
+		if (init_data)
+			config.init_data = &init_data[i];
+
+		if (i == PV88090_ID_BUCK2 || i == PV88090_ID_BUCK3) {
+			ret = regmap_read(chip->regmap,
+				pv88090_regulator_info[i].conf2, &conf2);
+			if (ret < 0)
+				return ret;
+
+			conf2 = (conf2 >> PV88090_BUCK_VDAC_RANGE_SHIFT) &
+				PV88090_BUCK_VDAC_RANGE_MASK;
+
+			ret = regmap_read(chip->regmap,
+				PV88090_REG_BUCK_FOLD_RANGE, &range);
+			if (ret < 0)
+				return ret;
+
+			range = (range >>
+				 (PV88080_BUCK_VRANGE_GAIN_SHIFT + i - 1)) &
+				PV88080_BUCK_VRANGE_GAIN_MASK;
+			index = ((range << 1) | conf2);
+
+			pv88090_regulator_info[i].desc.min_uV
+				= pv88090_buck_vol[index].min_uV;
+			pv88090_regulator_info[i].desc.uV_step
+				= pv88090_buck_vol[index].uV_step;
+			pv88090_regulator_info[i].desc.n_voltages
+				= ((pv88090_buck_vol[index].max_uV)
+				- (pv88090_buck_vol[index].min_uV))
+				/(pv88090_buck_vol[index].uV_step) + 1;
+		}
+
+		config.driver_data = (void *)&pv88090_regulator_info[i];
+		chip->rdev[i] = devm_regulator_register(chip->dev,
+			&pv88090_regulator_info[i].desc, &config);
+		if (IS_ERR(chip->rdev[i])) {
+			dev_err(chip->dev,
+				"Failed to register PV88090 regulator\n");
+			return PTR_ERR(chip->rdev[i]);
+		}
+	}
+
+	return 0;
+}
+
+static const struct i2c_device_id pv88090_i2c_id[] = {
+	{"pv88090", 0},
+	{},
+};
+MODULE_DEVICE_TABLE(i2c, pv88090_i2c_id);
+
+#ifdef CONFIG_OF
+static const struct of_device_id pv88090_dt_ids[] = {
+	{ .compatible = "pvs,pv88090", .data = &pv88090_i2c_id[0] },
+	{},
+};
+MODULE_DEVICE_TABLE(of, pv88090_dt_ids);
+#endif
+
+static struct i2c_driver pv88090_regulator_driver = {
+	.driver = {
+		.name = "pv88090",
+		.of_match_table = of_match_ptr(pv88090_dt_ids),
+	},
+	.probe = pv88090_i2c_probe,
+	.id_table = pv88090_i2c_id,
+};
+
+module_i2c_driver(pv88090_regulator_driver);
+
+MODULE_AUTHOR("James Ban <James.Ban.opensource@diasemi.com>");
+MODULE_DESCRIPTION("Regulator device driver for Powerventure PV88090");
+MODULE_LICENSE("GPL");

drivers/regulator/pv88090-regulator.h

+/*
+ * pv88090-regulator.h - Regulator definitions for PV88090
+ * Copyright (C) 2015 Powerventure Semiconductor Ltd.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __PV88090_REGISTERS_H__
+#define __PV88090_REGISTERS_H__
+
+/* System Control and Event Registers */
+#define	PV88090_REG_EVENT_A			0x03
+#define	PV88090_REG_MASK_A			0x06
+#define	PV88090_REG_MASK_B			0x07
+
+/* Regulator Registers */
+#define	PV88090_REG_BUCK1_CONF0			0x18
+#define	PV88090_REG_BUCK1_CONF1			0x19
+#define	PV88090_REG_BUCK1_CONF2			0x1a
+#define	PV88090_REG_BUCK2_CONF0			0x1b
+#define	PV88090_REG_BUCK2_CONF1			0x1c
+#define	PV88090_REG_BUCK2_CONF2			0x58
+#define	PV88090_REG_BUCK3_CONF0			0x1d
+#define	PV88090_REG_BUCK3_CONF1			0x1e
+#define	PV88090_REG_BUCK3_CONF2			0x5c
+
+#define	PV88090_REG_LDO1_CONT			0x1f
+#define	PV88090_REG_LDO2_CONT			0x20
+#define	PV88090_REG_LDO3_CONT			0x21
+#define	PV88090_REG_BUCK_FOLD_RANGE			0x61
+
+/* PV88090_REG_EVENT_A (addr=0x03) */
+#define	PV88090_E_VDD_FLT				0x01
+#define	PV88090_E_OVER_TEMP			0x02
+
+/* PV88090_REG_MASK_A (addr=0x06) */
+#define	PV88090_M_VDD_FLT				0x01
+#define	PV88090_M_OVER_TEMP			0x02
+
+/* PV88090_REG_BUCK1_CONF0 (addr=0x18) */
+#define	PV88090_BUCK1_EN				0x80
+#define PV88090_VBUCK1_MASK			0x7F
+/* PV88090_REG_BUCK2_CONF0 (addr=0x1b) */
+#define	PV88090_BUCK2_EN				0x80
+#define PV88090_VBUCK2_MASK			0x7F
+/* PV88090_REG_BUCK3_CONF0 (addr=0x1d) */
+#define	PV88090_BUCK3_EN				0x80
+#define PV88090_VBUCK3_MASK			0x7F
+/* PV88090_REG_LDO1_CONT (addr=0x1f) */
+#define	PV88090_LDO1_EN				0x40
+#define PV88090_VLDO1_MASK			0x3F
+/* PV88090_REG_LDO2_CONT (addr=0x20) */
+#define	PV88090_LDO2_EN				0x40
+#define PV88090_VLDO2_MASK			0x3F
+
+/* PV88090_REG_BUCK1_CONF1 (addr=0x19) */
+#define PV88090_BUCK1_ILIM_SHIFT			2
+#define PV88090_BUCK1_ILIM_MASK			0x7C
+#define PV88090_BUCK1_MODE_MASK			0x03
+
+/* PV88090_REG_BUCK2_CONF1 (addr=0x1c) */
+#define PV88090_BUCK2_ILIM_SHIFT			2
+#define PV88090_BUCK2_ILIM_MASK			0x0C
+#define PV88090_BUCK2_MODE_MASK			0x03
+
+/* PV88090_REG_BUCK3_CONF1 (addr=0x1e) */
+#define PV88090_BUCK3_ILIM_SHIFT			2
+#define PV88090_BUCK3_ILIM_MASK			0x0C
+#define PV88090_BUCK3_MODE_MASK			0x03
+
+#define	PV88090_BUCK_MODE_SLEEP			0x00
+#define	PV88090_BUCK_MODE_AUTO			0x01
+#define	PV88090_BUCK_MODE_SYNC			0x02
+
+/* PV88090_REG_BUCK2_CONF2 (addr=0x58) */
+/* PV88090_REG_BUCK3_CONF2 (addr=0x5c) */
+#define PV88090_BUCK_VDAC_RANGE_SHIFT			7
+#define PV88090_BUCK_VDAC_RANGE_MASK			0x01
+
+#define PV88090_BUCK_VDAC_RANGE_1			0x00
+#define PV88090_BUCK_VDAC_RANGE_2			0x01
+
+/* PV88090_REG_BUCK_FOLD_RANGE (addr=0x61) */
+#define PV88080_BUCK_VRANGE_GAIN_SHIFT			3
+#define PV88080_BUCK_VRANGE_GAIN_MASK			0x01
+
+#define PV88080_BUCK_VRANGE_GAIN_1			0x00
+#define PV88080_BUCK_VRANGE_GAIN_2			0x01
+
+#endif	/* __PV88090_REGISTERS_H__ */

drivers/regulator/qcom_smd-regulator.c

@@ -153,6 +153,49 @@ static const struct regulator_ops rpm_switch_ops = {
 	.is_enabled = rpm_reg_is_enabled,
 };
 
+static const struct regulator_desc pma8084_hfsmps = {
+	.linear_ranges = (struct regulator_linear_range[]) {
+		REGULATOR_LINEAR_RANGE(375000,  0,  95, 12500),
+		REGULATOR_LINEAR_RANGE(1550000, 96, 158, 25000),
+	},
+	.n_linear_ranges = 2,
+	.n_voltages = 159,
+	.ops = &rpm_smps_ldo_ops,
+};
+
+static const struct regulator_desc pma8084_ftsmps = {
+	.linear_ranges = (struct regulator_linear_range[]) {
+		REGULATOR_LINEAR_RANGE(350000,  0, 184, 5000),
+		REGULATOR_LINEAR_RANGE(700000, 185, 339, 10000),
+	},
+	.n_linear_ranges = 2,
+	.n_voltages = 340,
+	.ops = &rpm_smps_ldo_ops,
+};
+
+static const struct regulator_desc pma8084_pldo = {
+	.linear_ranges = (struct regulator_linear_range[]) {
+		REGULATOR_LINEAR_RANGE(750000,  0,  30, 25000),
+		REGULATOR_LINEAR_RANGE(1500000, 31, 99, 50000),
+	},
+	.n_linear_ranges = 2,
+	.n_voltages = 100,
+	.ops = &rpm_smps_ldo_ops,
+};
+
+static const struct regulator_desc pma8084_nldo = {
+	.linear_ranges = (struct regulator_linear_range[]) {
+		REGULATOR_LINEAR_RANGE(750000, 0, 63, 12500),
+	},
+	.n_linear_ranges = 1,
+	.n_voltages = 64,
+	.ops = &rpm_smps_ldo_ops,
+};
+
+static const struct regulator_desc pma8084_switch = {
+	.ops = &rpm_switch_ops,
+};
+
 static const struct regulator_desc pm8x41_hfsmps = {
 	.linear_ranges = (struct regulator_linear_range[]) {
 		REGULATOR_LINEAR_RANGE( 375000,  0,  95, 12500),
@@ -211,6 +254,43 @@ static const struct regulator_desc pm8941_switch = {
 	.ops = &rpm_switch_ops,
 };
 
+static const struct regulator_desc pm8916_pldo = {
+	.linear_ranges = (struct regulator_linear_range[]) {
+		REGULATOR_LINEAR_RANGE(750000, 0, 208, 12500),
+	},
+	.n_linear_ranges = 1,
+	.n_voltages = 209,
+	.ops = &rpm_smps_ldo_ops,
+};
+
+static const struct regulator_desc pm8916_nldo = {
+	.linear_ranges = (struct regulator_linear_range[]) {
+		REGULATOR_LINEAR_RANGE(375000, 0, 93, 12500),
+	},
+	.n_linear_ranges = 1,
+	.n_voltages = 94,
+	.ops = &rpm_smps_ldo_ops,
+};
+
+static const struct regulator_desc pm8916_buck_lvo_smps = {
+	.linear_ranges = (struct regulator_linear_range[]) {
+		REGULATOR_LINEAR_RANGE(375000, 0, 95, 12500),
+		REGULATOR_LINEAR_RANGE(750000, 96, 127, 25000),
+	},
+	.n_linear_ranges = 2,
+	.n_voltages = 128,
+	.ops = &rpm_smps_ldo_ops,
+};
+
+static const struct regulator_desc pm8916_buck_hvo_smps = {
+	.linear_ranges = (struct regulator_linear_range[]) {
+		REGULATOR_LINEAR_RANGE(1550000, 0, 31, 25000),
+	},
+	.n_linear_ranges = 1,
+	.n_voltages = 32,
+	.ops = &rpm_smps_ldo_ops,
+};
+
 struct rpm_regulator_data {
 	const char *name;
 	u32 type;
@@ -231,6 +311,32 @@ static const struct rpm_regulator_data rpm_pm8841_regulators[] = {
 	{}
 };
 
+static const struct rpm_regulator_data rpm_pm8916_regulators[] = {
+	{ "s1", QCOM_SMD_RPM_SMPA, 1, &pm8916_buck_lvo_smps, "vdd_s1" },
+	{ "s2", QCOM_SMD_RPM_SMPA, 2, &pm8916_buck_lvo_smps, "vdd_s2" },
+	{ "s3", QCOM_SMD_RPM_SMPA, 3, &pm8916_buck_lvo_smps, "vdd_s3" },
+	{ "s4", QCOM_SMD_RPM_SMPA, 4, &pm8916_buck_hvo_smps, "vdd_s4" },
+	{ "l1", QCOM_SMD_RPM_LDOA, 1, &pm8916_nldo, "vdd_l1_l2_l3" },
+	{ "l2", QCOM_SMD_RPM_LDOA, 2, &pm8916_nldo, "vdd_l1_l2_l3" },
+	{ "l3", QCOM_SMD_RPM_LDOA, 3, &pm8916_nldo, "vdd_l1_l2_l3" },
+	{ "l4", QCOM_SMD_RPM_LDOA, 4, &pm8916_pldo, "vdd_l4_l5_l6" },
+	{ "l5", QCOM_SMD_RPM_LDOA, 5, &pm8916_pldo, "vdd_l4_l5_l6" },
+	{ "l6", QCOM_SMD_RPM_LDOA, 6, &pm8916_pldo, "vdd_l4_l5_l6" },
+	{ "l7", QCOM_SMD_RPM_LDOA, 7, &pm8916_pldo, "vdd_l7" },
+	{ "l8", QCOM_SMD_RPM_LDOA, 8, &pm8916_pldo, "vdd_l8_l9_l10_l11_l12_l13_l14_l15_l16_l17_l18" },
+	{ "l9", QCOM_SMD_RPM_LDOA, 9, &pm8916_pldo, "vdd_l8_l9_l10_l11_l12_l13_l14_l15_l16_l17_l18" },
+	{ "l10", QCOM_SMD_RPM_LDOA, 10, &pm8916_pldo, "vdd_l8_l9_l10_l11_l12_l13_l14_l15_l16_l17_l18"},
+	{ "l11", QCOM_SMD_RPM_LDOA, 11, &pm8916_pldo, "vdd_l8_l9_l10_l11_l12_l13_l14_l15_l16_l17_l18"},
+	{ "l12", QCOM_SMD_RPM_LDOA, 12, &pm8916_pldo, "vdd_l8_l9_l10_l11_l12_l13_l14_l15_l16_l17_l18"},
+	{ "l13", QCOM_SMD_RPM_LDOA, 13, &pm8916_pldo, "vdd_l8_l9_l10_l11_l12_l13_l14_l15_l16_l17_l18"},
+	{ "l14", QCOM_SMD_RPM_LDOA, 14, &pm8916_pldo, "vdd_l8_l9_l10_l11_l12_l13_l14_l15_l16_l17_l18"},
+	{ "l15", QCOM_SMD_RPM_LDOA, 15, &pm8916_pldo, "vdd_l8_l9_l10_l11_l12_l13_l14_l15_l16_l17_l18"},
+	{ "l16", QCOM_SMD_RPM_LDOA, 16, &pm8916_pldo, "vdd_l8_l9_l10_l11_l12_l13_l14_l15_l16_l17_l18"},
+	{ "l17", QCOM_SMD_RPM_LDOA, 17, &pm8916_pldo, "vdd_l8_l9_l10_l11_l12_l13_l14_l15_l16_l17_l18"},
+	{ "l18", QCOM_SMD_RPM_LDOA, 18, &pm8916_pldo, "vdd_l8_l9_l10_l11_l12_l13_l14_l15_l16_l17_l18"},
+	{}
+};
+
 static const struct rpm_regulator_data rpm_pm8941_regulators[] = {
 	{ "s1", QCOM_SMD_RPM_SMPA, 1, &pm8x41_hfsmps, "vdd_s1" },
 	{ "s2", QCOM_SMD_RPM_SMPA, 2, &pm8x41_hfsmps, "vdd_s2" },
@@ -272,9 +378,62 @@ static const struct rpm_regulator_data rpm_pm8941_regulators[] = {
 	{}
 };
 
+static const struct rpm_regulator_data rpm_pma8084_regulators[] = {
+	{ "s1", QCOM_SMD_RPM_SMPA, 1, &pma8084_ftsmps, "vdd_s1" },
+	{ "s2", QCOM_SMD_RPM_SMPA, 2, &pma8084_ftsmps, "vdd_s2" },
+	{ "s3", QCOM_SMD_RPM_SMPA, 3, &pma8084_hfsmps, "vdd_s3" },
+	{ "s4", QCOM_SMD_RPM_SMPA, 4, &pma8084_hfsmps, "vdd_s4" },
+	{ "s5", QCOM_SMD_RPM_SMPA, 5, &pma8084_hfsmps, "vdd_s5" },
+	{ "s6", QCOM_SMD_RPM_SMPA, 6, &pma8084_ftsmps, "vdd_s6" },
+	{ "s7", QCOM_SMD_RPM_SMPA, 7, &pma8084_ftsmps, "vdd_s7" },
+	{ "s8", QCOM_SMD_RPM_SMPA, 8, &pma8084_ftsmps, "vdd_s8" },
+	{ "s9", QCOM_SMD_RPM_SMPA, 9, &pma8084_ftsmps, "vdd_s9" },
+	{ "s10", QCOM_SMD_RPM_SMPA, 10, &pma8084_ftsmps, "vdd_s10" },
+	{ "s11", QCOM_SMD_RPM_SMPA, 11, &pma8084_ftsmps, "vdd_s11" },
+	{ "s12", QCOM_SMD_RPM_SMPA, 12, &pma8084_ftsmps, "vdd_s12" },
+
+	{ "l1", QCOM_SMD_RPM_LDOA, 1, &pma8084_nldo, "vdd_l1_l11" },
+	{ "l2", QCOM_SMD_RPM_LDOA, 2, &pma8084_nldo, "vdd_l2_l3_l4_l27" },
+	{ "l3", QCOM_SMD_RPM_LDOA, 3, &pma8084_nldo, "vdd_l2_l3_l4_l27" },
+	{ "l4", QCOM_SMD_RPM_LDOA, 4, &pma8084_nldo, "vdd_l2_l3_l4_l27" },
+	{ "l5", QCOM_SMD_RPM_LDOA, 5, &pma8084_pldo, "vdd_l5_l7" },
+	{ "l6", QCOM_SMD_RPM_LDOA, 6, &pma8084_pldo, "vdd_l6_l12_l14_l15_l26" },
+	{ "l7", QCOM_SMD_RPM_LDOA, 7, &pma8084_pldo, "vdd_l5_l7" },
+	{ "l8", QCOM_SMD_RPM_LDOA, 8, &pma8084_pldo, "vdd_l8" },
+	{ "l9", QCOM_SMD_RPM_LDOA, 9, &pma8084_pldo, "vdd_l9_l10_l13_l20_l23_l24" },
+	{ "l10", QCOM_SMD_RPM_LDOA, 10, &pma8084_pldo, "vdd_l9_l10_l13_l20_l23_l24" },
+	{ "l11", QCOM_SMD_RPM_LDOA, 11, &pma8084_nldo, "vdd_l1_l11" },
+	{ "l12", QCOM_SMD_RPM_LDOA, 12, &pma8084_pldo, "vdd_l6_l12_l14_l15_l26" },
+	{ "l13", QCOM_SMD_RPM_LDOA, 13, &pma8084_pldo, "vdd_l9_l10_l13_l20_l23_l24" },
+	{ "l14", QCOM_SMD_RPM_LDOA, 14, &pma8084_pldo, "vdd_l6_l12_l14_l15_l26" },
+	{ "l15", QCOM_SMD_RPM_LDOA, 15, &pma8084_pldo, "vdd_l6_l12_l14_l15_l26" },
+	{ "l16", QCOM_SMD_RPM_LDOA, 16, &pma8084_pldo, "vdd_l16_l25" },
+	{ "l17", QCOM_SMD_RPM_LDOA, 17, &pma8084_pldo, "vdd_l17" },
+	{ "l18", QCOM_SMD_RPM_LDOA, 18, &pma8084_pldo, "vdd_l18" },
+	{ "l19", QCOM_SMD_RPM_LDOA, 19, &pma8084_pldo, "vdd_l19" },
+	{ "l20", QCOM_SMD_RPM_LDOA, 20, &pma8084_pldo, "vdd_l9_l10_l13_l20_l23_l24" },
+	{ "l21", QCOM_SMD_RPM_LDOA, 21, &pma8084_pldo, "vdd_l21" },
+	{ "l22", QCOM_SMD_RPM_LDOA, 22, &pma8084_pldo, "vdd_l22" },
+	{ "l23", QCOM_SMD_RPM_LDOA, 23, &pma8084_pldo, "vdd_l9_l10_l13_l20_l23_l24" },
+	{ "l24", QCOM_SMD_RPM_LDOA, 24, &pma8084_pldo, "vdd_l9_l10_l13_l20_l23_l24" },
+	{ "l25", QCOM_SMD_RPM_LDOA, 25, &pma8084_pldo, "vdd_l16_l25" },
+	{ "l26", QCOM_SMD_RPM_LDOA, 26, &pma8084_pldo, "vdd_l6_l12_l14_l15_l26" },
+	{ "l27", QCOM_SMD_RPM_LDOA, 27, &pma8084_nldo, "vdd_l2_l3_l4_l27" },
+
+	{ "lvs1", QCOM_SMD_RPM_VSA, 1, &pma8084_switch },
+	{ "lvs2", QCOM_SMD_RPM_VSA, 2, &pma8084_switch },
+	{ "lvs3", QCOM_SMD_RPM_VSA, 3, &pma8084_switch },
+	{ "lvs4", QCOM_SMD_RPM_VSA, 4, &pma8084_switch },
+	{ "5vs1", QCOM_SMD_RPM_VSA, 5, &pma8084_switch },
+
+	{}
+};
+
 static const struct of_device_id rpm_of_match[] = {
 	{ .compatible = "qcom,rpm-pm8841-regulators", .data = &rpm_pm8841_regulators },
+	{ .compatible = "qcom,rpm-pm8916-regulators", .data = &rpm_pm8916_regulators },
 	{ .compatible = "qcom,rpm-pm8941-regulators", .data = &rpm_pm8941_regulators },
+	{ .compatible = "qcom,rpm-pma8084-regulators", .data = &rpm_pma8084_regulators },
 	{}
 };
 MODULE_DEVICE_TABLE(of, rpm_of_match);

drivers/regulator/tps6105x-regulator.c

@@ -27,90 +27,12 @@ static const unsigned int tps6105x_voltages[] = {
 	5000000, /* There is an additional 5V */
 };
 
-static int tps6105x_regulator_enable(struct regulator_dev *rdev)
-{
-	struct tps6105x *tps6105x = rdev_get_drvdata(rdev);
-	int ret;
-
-	/* Activate voltage mode */
-	ret = regmap_update_bits(tps6105x->regmap, TPS6105X_REG_0,
-		TPS6105X_REG0_MODE_MASK,
-		TPS6105X_REG0_MODE_VOLTAGE << TPS6105X_REG0_MODE_SHIFT);
-	if (ret)
-		return ret;
-
-	return 0;
-}
-
-static int tps6105x_regulator_disable(struct regulator_dev *rdev)
-{
-	struct tps6105x *tps6105x = rdev_get_drvdata(rdev);
-	int ret;
-
-	/* Set into shutdown mode */
-	ret = regmap_update_bits(tps6105x->regmap, TPS6105X_REG_0,
-		TPS6105X_REG0_MODE_MASK,
-		TPS6105X_REG0_MODE_SHUTDOWN << TPS6105X_REG0_MODE_SHIFT);
-	if (ret)
-		return ret;
-
-	return 0;
-}
-
-static int tps6105x_regulator_is_enabled(struct regulator_dev *rdev)
-{
-	struct tps6105x *tps6105x = rdev_get_drvdata(rdev);
-	unsigned int regval;
-	int ret;
-
-	ret = regmap_read(tps6105x->regmap, TPS6105X_REG_0, &regval);
-	if (ret)
-		return ret;
-	regval &= TPS6105X_REG0_MODE_MASK;
-	regval >>= TPS6105X_REG0_MODE_SHIFT;
-
-	if (regval == TPS6105X_REG0_MODE_VOLTAGE)
-		return 1;
-
-	return 0;
-}
-
-static int tps6105x_regulator_get_voltage_sel(struct regulator_dev *rdev)
-{
-	struct tps6105x *tps6105x = rdev_get_drvdata(rdev);
-	unsigned int regval;
-	int ret;
-
-	ret = regmap_read(tps6105x->regmap, TPS6105X_REG_0, &regval);
-	if (ret)
-		return ret;
-
-	regval &= TPS6105X_REG0_VOLTAGE_MASK;
-	regval >>= TPS6105X_REG0_VOLTAGE_SHIFT;
-	return (int) regval;
-}
-
-static int tps6105x_regulator_set_voltage_sel(struct regulator_dev *rdev,
-					      unsigned selector)
-{
-	struct tps6105x *tps6105x = rdev_get_drvdata(rdev);
-	int ret;
-
-	ret = regmap_update_bits(tps6105x->regmap, TPS6105X_REG_0,
-				    TPS6105X_REG0_VOLTAGE_MASK,
-				    selector << TPS6105X_REG0_VOLTAGE_SHIFT);
-	if (ret)
-		return ret;
-
-	return 0;
-}
-
 static struct regulator_ops tps6105x_regulator_ops = {
-	.enable		= tps6105x_regulator_enable,
-	.disable	= tps6105x_regulator_disable,
-	.is_enabled	= tps6105x_regulator_is_enabled,
-	.get_voltage_sel = tps6105x_regulator_get_voltage_sel,
-	.set_voltage_sel = tps6105x_regulator_set_voltage_sel,
+	.enable		= regulator_enable_regmap,
+	.disable	= regulator_disable_regmap,
+	.is_enabled	= regulator_is_enabled_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
 	.list_voltage	= regulator_list_voltage_table,
 };
 
@@ -122,6 +44,12 @@ static const struct regulator_desc tps6105x_regulator_desc = {
 	.owner		= THIS_MODULE,
 	.n_voltages	= ARRAY_SIZE(tps6105x_voltages),
 	.volt_table	= tps6105x_voltages,
+	.vsel_reg	= TPS6105X_REG_0,
+	.vsel_mask	= TPS6105X_REG0_VOLTAGE_MASK,
+	.enable_reg	= TPS6105X_REG_0,
+	.enable_mask	= TPS6105X_REG0_MODE_MASK,
+	.enable_val	= TPS6105X_REG0_MODE_VOLTAGE <<
+			  TPS6105X_REG0_MODE_SHIFT,
 };
 
 /*
@@ -144,6 +72,7 @@ static int tps6105x_regulator_probe(struct platform_device *pdev)
 	config.dev = &tps6105x->client->dev;
 	config.init_data = pdata->regulator_data;
 	config.driver_data = tps6105x;
+	config.regmap = tps6105x->regmap;
 
 	/* Register regulator with framework */
 	tps6105x->regulator = devm_regulator_register(&pdev->dev,

drivers/regulator/tps65086-regulator.c

+/*
+ * Copyright (C) 2015 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Author: Andrew F. Davis <afd@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether expressed or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License version 2 for more details.
+ *
+ * Based on the TPS65912 driver
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+
+#include <linux/mfd/tps65086.h>
+
+enum tps65086_regulators { BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6, LDOA1,
+	LDOA2, LDOA3, SWA1, SWB1, SWB2, VTT };
+
+#define TPS65086_REGULATOR(_name, _of, _id, _nv, _vr, _vm, _er, _em, _lr, _dr, _dm)	\
+	[_id] = {							\
+		.desc = {						\
+			.name			= _name,		\
+			.of_match		= of_match_ptr(_of),	\
+			.regulators_node	= "regulators",		\
+			.of_parse_cb		= tps65086_of_parse_cb,	\
+			.id			= _id,			\
+			.ops			= &reg_ops,		\
+			.n_voltages		= _nv,			\
+			.type			= REGULATOR_VOLTAGE,	\
+			.owner			= THIS_MODULE,		\
+			.vsel_reg		= _vr,			\
+			.vsel_mask		= _vm,			\
+			.enable_reg		= _er,			\
+			.enable_mask		= _em,			\
+			.volt_table		= NULL,			\
+			.linear_ranges		= _lr,			\
+			.n_linear_ranges	= ARRAY_SIZE(_lr),	\
+		},							\
+		.decay_reg = _dr,					\
+		.decay_mask = _dm,					\
+	}
+
+#define TPS65086_SWITCH(_name, _of, _id, _er, _em)			\
+	[_id] = {							\
+		.desc = {						\
+			.name			= _name,		\
+			.of_match		= of_match_ptr(_of),	\
+			.regulators_node	= "regulators",		\
+			.of_parse_cb		= tps65086_of_parse_cb,	\
+			.id			= _id,			\
+			.ops			= &switch_ops,		\
+			.type			= REGULATOR_VOLTAGE,	\
+			.owner			= THIS_MODULE,		\
+			.enable_reg		= _er,			\
+			.enable_mask		= _em,			\
+		},							\
+	}
+
+struct tps65086_regulator {
+	struct regulator_desc desc;
+	unsigned int decay_reg;
+	unsigned int decay_mask;
+};
+
+static const struct regulator_linear_range tps65086_buck126_10mv_ranges[] = {
+	REGULATOR_LINEAR_RANGE(0, 0x0, 0x0, 0),
+	REGULATOR_LINEAR_RANGE(410000, 0x1, 0x7F, 10000),
+};
+
+static const struct regulator_linear_range tps65086_buck126_25mv_ranges[] = {
+	REGULATOR_LINEAR_RANGE(0, 0x0, 0x0, 0),
+	REGULATOR_LINEAR_RANGE(1000000, 0x1, 0x18, 0),
+	REGULATOR_LINEAR_RANGE(1025000, 0x19, 0x7F, 25000),
+};
+
+static const struct regulator_linear_range tps65086_buck345_ranges[] = {
+	REGULATOR_LINEAR_RANGE(0, 0x0, 0x0, 0),
+	REGULATOR_LINEAR_RANGE(425000, 0x1, 0x7F, 25000),
+};
+
+static const struct regulator_linear_range tps65086_ldoa1_ranges[] = {
+	REGULATOR_LINEAR_RANGE(1350000, 0x0, 0x0, 0),
+	REGULATOR_LINEAR_RANGE(1500000, 0x1, 0x7, 100000),
+	REGULATOR_LINEAR_RANGE(2300000, 0x8, 0xA, 100000),
+	REGULATOR_LINEAR_RANGE(2700000, 0xB, 0xD, 150000),
+	REGULATOR_LINEAR_RANGE(3300000, 0xE, 0xE, 0),
+};
+
+static const struct regulator_linear_range tps65086_ldoa23_ranges[] = {
+	REGULATOR_LINEAR_RANGE(700000, 0x0, 0xD, 50000),
+	REGULATOR_LINEAR_RANGE(1400000, 0xE, 0xF, 100000),
+};
+
+/* Operations permitted on regulators */
+static struct regulator_ops reg_ops = {
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.is_enabled		= regulator_is_enabled_regmap,
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+	.map_voltage		= regulator_map_voltage_linear_range,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.list_voltage		= regulator_list_voltage_linear_range,
+};
+
+/* Operations permitted on load switches */
+static struct regulator_ops switch_ops = {
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.is_enabled		= regulator_is_enabled_regmap,
+};
+
+static int tps65086_of_parse_cb(struct device_node *dev,
+				const struct regulator_desc *desc,
+				struct regulator_config *config);
+
+static struct tps65086_regulator regulators[] = {
+	TPS65086_REGULATOR("BUCK1", "buck1", BUCK1, 0x80, TPS65086_BUCK1CTRL,
+			   BUCK_VID_MASK, TPS65086_BUCK123CTRL, BIT(0),
+			   tps65086_buck126_10mv_ranges, TPS65086_BUCK1CTRL,
+			   BIT(0)),
+	TPS65086_REGULATOR("BUCK2", "buck2", BUCK2, 0x80, TPS65086_BUCK2CTRL,
+			   BUCK_VID_MASK, TPS65086_BUCK123CTRL, BIT(1),
+			   tps65086_buck126_10mv_ranges, TPS65086_BUCK2CTRL,
+			   BIT(0)),
+	TPS65086_REGULATOR("BUCK3", "buck3", BUCK3, 0x80, TPS65086_BUCK3VID,
+			   BUCK_VID_MASK, TPS65086_BUCK123CTRL, BIT(2),
+			   tps65086_buck345_ranges, TPS65086_BUCK3DECAY,
+			   BIT(0)),
+	TPS65086_REGULATOR("BUCK4", "buck4", BUCK4, 0x80, TPS65086_BUCK4VID,
+			   BUCK_VID_MASK, TPS65086_BUCK4CTRL, BIT(0),
+			   tps65086_buck345_ranges, TPS65086_BUCK4VID,
+			   BIT(0)),
+	TPS65086_REGULATOR("BUCK5", "buck5", BUCK5, 0x80, TPS65086_BUCK5VID,
+			   BUCK_VID_MASK, TPS65086_BUCK5CTRL, BIT(0),
+			   tps65086_buck345_ranges, TPS65086_BUCK5CTRL,
+			   BIT(0)),
+	TPS65086_REGULATOR("BUCK6", "buck6", BUCK6, 0x80, TPS65086_BUCK6VID,
+			   BUCK_VID_MASK, TPS65086_BUCK6CTRL, BIT(0),
+			   tps65086_buck126_10mv_ranges, TPS65086_BUCK6CTRL,
+			   BIT(0)),
+	TPS65086_REGULATOR("LDOA1", "ldoa1", LDOA1, 0xF, TPS65086_LDOA1CTRL,
+			   VDOA1_VID_MASK, TPS65086_LDOA1CTRL, BIT(0),
+			   tps65086_ldoa1_ranges, 0, 0),
+	TPS65086_REGULATOR("LDOA2", "ldoa2", LDOA2, 0x10, TPS65086_LDOA2VID,
+			   VDOA23_VID_MASK, TPS65086_LDOA2CTRL, BIT(0),
+			   tps65086_ldoa23_ranges, 0, 0),
+	TPS65086_REGULATOR("LDOA3", "ldoa3", LDOA3, 0x10, TPS65086_LDOA3VID,
+			   VDOA23_VID_MASK, TPS65086_LDOA3CTRL, BIT(0),
+			   tps65086_ldoa23_ranges, 0, 0),
+	TPS65086_SWITCH("SWA1", "swa1", SWA1, TPS65086_SWVTT_EN, BIT(5)),
+	TPS65086_SWITCH("SWB1", "swa2", SWB1, TPS65086_SWVTT_EN, BIT(6)),
+	TPS65086_SWITCH("SWB2", "swa3", SWB2, TPS65086_SWVTT_EN, BIT(7)),
+	TPS65086_SWITCH("VTT", "vtt", VTT, TPS65086_SWVTT_EN, BIT(4)),
+};
+
+static inline bool has_25mv_mode(int id)
+{
+	switch (id) {
+	case BUCK1:
+	case BUCK2:
+	case BUCK6:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static int tps65086_of_parse_cb(struct device_node *dev,
+				const struct regulator_desc *desc,
+				struct regulator_config *config)
+{
+	int ret;
+
+	/* Check for 25mV step mode */
+	if (has_25mv_mode(desc->id) &&
+			of_property_read_bool(config->of_node, "ti,regulator-step-size-25mv")) {
+		regulators[desc->id].desc.linear_ranges =
+				tps65086_buck126_25mv_ranges;
+		regulators[desc->id].desc.n_linear_ranges =
+				ARRAY_SIZE(tps65086_buck126_25mv_ranges);
+	}
+
+	/* Check for decay mode */
+	if (desc->id <= BUCK6 && of_property_read_bool(config->of_node, "ti,regulator-decay")) {
+		ret = regmap_write_bits(config->regmap,
+					regulators[desc->id].decay_reg,
+					regulators[desc->id].decay_mask,
+					regulators[desc->id].decay_mask);
+		if (ret) {
+			dev_err(config->dev, "Error setting decay\n");
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static int tps65086_regulator_probe(struct platform_device *pdev)
+{
+	struct tps65086 *tps = dev_get_drvdata(pdev->dev.parent);
+	struct regulator_config config = { };
+	struct regulator_dev *rdev;
+	int i;
+
+	platform_set_drvdata(pdev, tps);
+
+	config.dev = &pdev->dev;
+	config.dev->of_node = tps->dev->of_node;
+	config.driver_data = tps;
+	config.regmap = tps->regmap;
+
+	for (i = 0; i < ARRAY_SIZE(regulators); i++) {
+		rdev = devm_regulator_register(&pdev->dev, &regulators[i].desc,
+					       &config);
+		if (IS_ERR(rdev)) {
+			dev_err(tps->dev, "failed to register %s regulator\n",
+				pdev->name);
+			return PTR_ERR(rdev);
+		}
+	}
+
+	return 0;
+}
+
+static const struct platform_device_id tps65086_regulator_id_table[] = {
+	{ "tps65086-regulator", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(platform, tps65086_regulator_id_table);
+
+static struct platform_driver tps65086_regulator_driver = {
+	.driver = {
+		.name = "tps65086-regulator",
+	},
+	.probe = tps65086_regulator_probe,
+	.id_table = tps65086_regulator_id_table,
+};
+module_platform_driver(tps65086_regulator_driver);
+
+MODULE_AUTHOR("Andrew F. Davis <afd@ti.com>");
+MODULE_DESCRIPTION("TPS65086 Regulator driver");
+MODULE_LICENSE("GPL v2");

drivers/regulator/tps65218-regulator.c

@@ -27,19 +27,22 @@
 #include <linux/regulator/machine.h>
 #include <linux/mfd/tps65218.h>
 
-enum tps65218_regulators { DCDC1, DCDC2, DCDC3, DCDC4, DCDC5, DCDC6, LDO1 };
+enum tps65218_regulators { DCDC1, DCDC2, DCDC3, DCDC4,
+			   DCDC5, DCDC6, LDO1, LS3 };
 
-#define TPS65218_REGULATOR(_name, _id, _ops, _n, _vr, _vm, _er, _em, \
-			    _lr, _nlr, _delay, _fuv)		\
+#define TPS65218_REGULATOR(_name, _id, _type, _ops, _n, _vr, _vm, _er, _em, \
+			    _cr, _cm, _lr, _nlr, _delay, _fuv)		\
 	{							\
 		.name			= _name,		\
 		.id			= _id,			\
 		.ops			= &_ops,		\
 		.n_voltages		= _n,			\
-		.type			= REGULATOR_VOLTAGE,	\
+		.type			= _type,	\
 		.owner			= THIS_MODULE,		\
 		.vsel_reg		= _vr,			\
 		.vsel_mask		= _vm,			\
+		.csel_reg		= _cr,			\
+		.csel_mask		= _cm,			\
 		.enable_reg		= _er,			\
 		.enable_mask		= _em,			\
 		.volt_table		= NULL,			\
@@ -80,6 +83,7 @@ static struct tps_info tps65218_pmic_regs[] = {
 	TPS65218_INFO(DCDC5, "DCDC5", 1000000, 1000000),
 	TPS65218_INFO(DCDC6, "DCDC6", 1800000, 1800000),
 	TPS65218_INFO(LDO1, "LDO1", 900000, 3400000),
+	TPS65218_INFO(LS3, "LS3", -1, -1),
 };
 
 #define TPS65218_OF_MATCH(comp, label) \
@@ -96,6 +100,7 @@ static const struct of_device_id tps65218_of_match[] = {
 	TPS65218_OF_MATCH("ti,tps65218-dcdc5", tps65218_pmic_regs[DCDC5]),
 	TPS65218_OF_MATCH("ti,tps65218-dcdc6", tps65218_pmic_regs[DCDC6]),
 	TPS65218_OF_MATCH("ti,tps65218-ldo1", tps65218_pmic_regs[LDO1]),
+	TPS65218_OF_MATCH("ti,tps65218-ls3", tps65218_pmic_regs[LS3]),
 	{ }
 };
 MODULE_DEVICE_TABLE(of, tps65218_of_match);
@@ -175,6 +180,68 @@ static struct regulator_ops tps65218_ldo1_dcdc34_ops = {
 	.map_voltage		= regulator_map_voltage_linear_range,
 };
 
+static const int ls3_currents[] = { 100, 200, 500, 1000 };
+
+static int tps65218_pmic_set_input_current_lim(struct regulator_dev *dev,
+					       int lim_uA)
+{
+	unsigned int index = 0;
+	unsigned int num_currents = ARRAY_SIZE(ls3_currents);
+	struct tps65218 *tps = rdev_get_drvdata(dev);
+
+	while (index < num_currents && ls3_currents[index] != lim_uA)
+		index++;
+
+	if (index == num_currents)
+		return -EINVAL;
+
+	return tps65218_set_bits(tps, dev->desc->csel_reg, dev->desc->csel_mask,
+				 index << 2, TPS65218_PROTECT_L1);
+}
+
+static int tps65218_pmic_set_current_limit(struct regulator_dev *dev,
+					   int min_uA, int max_uA)
+{
+	int index = 0;
+	unsigned int num_currents = ARRAY_SIZE(ls3_currents);
+	struct tps65218 *tps = rdev_get_drvdata(dev);
+
+	while (index < num_currents && ls3_currents[index] < max_uA)
+		index++;
+
+	index--;
+
+	if (index < 0 || ls3_currents[index] < min_uA)
+		return -EINVAL;
+
+	return tps65218_set_bits(tps, dev->desc->csel_reg, dev->desc->csel_mask,
+				 index << 2, TPS65218_PROTECT_L1);
+}
+
+static int tps65218_pmic_get_current_limit(struct regulator_dev *dev)
+{
+	int retval;
+	unsigned int index;
+	struct tps65218 *tps = rdev_get_drvdata(dev);
+
+	retval = tps65218_reg_read(tps, dev->desc->csel_reg, &index);
+	if (retval < 0)
+		return retval;
+
+	index = (index & dev->desc->csel_mask) >> 2;
+
+	return ls3_currents[index];
+}
+
+static struct regulator_ops tps65218_ls3_ops = {
+	.is_enabled		= regulator_is_enabled_regmap,
+	.enable			= tps65218_pmic_enable,
+	.disable		= tps65218_pmic_disable,
+	.set_input_current_limit = tps65218_pmic_set_input_current_lim,
+	.set_current_limit	= tps65218_pmic_set_current_limit,
+	.get_current_limit	= tps65218_pmic_get_current_limit,
+};
+
 /* Operations permitted on DCDC5, DCDC6 */
 static struct regulator_ops tps65218_dcdc56_pmic_ops = {
 	.is_enabled		= regulator_is_enabled_regmap,
@@ -183,36 +250,46 @@ static struct regulator_ops tps65218_dcdc56_pmic_ops = {
 };
 
 static const struct regulator_desc regulators[] = {
-	TPS65218_REGULATOR("DCDC1", TPS65218_DCDC_1, tps65218_dcdc12_ops, 64,
-			   TPS65218_REG_CONTROL_DCDC1,
-			   TPS65218_CONTROL_DCDC1_MASK,
-			   TPS65218_REG_ENABLE1, TPS65218_ENABLE1_DC1_EN,
-			   dcdc1_dcdc2_ranges, 2, 4000, 0),
-	TPS65218_REGULATOR("DCDC2", TPS65218_DCDC_2, tps65218_dcdc12_ops, 64,
-			   TPS65218_REG_CONTROL_DCDC2,
-			   TPS65218_CONTROL_DCDC2_MASK,
-			   TPS65218_REG_ENABLE1, TPS65218_ENABLE1_DC2_EN,
-			   dcdc1_dcdc2_ranges, 2, 4000, 0),
-	TPS65218_REGULATOR("DCDC3", TPS65218_DCDC_3, tps65218_ldo1_dcdc34_ops,
-			   64, TPS65218_REG_CONTROL_DCDC3,
+	TPS65218_REGULATOR("DCDC1", TPS65218_DCDC_1, REGULATOR_VOLTAGE,
+			   tps65218_dcdc12_ops, 64, TPS65218_REG_CONTROL_DCDC1,
+			   TPS65218_CONTROL_DCDC1_MASK, TPS65218_REG_ENABLE1,
+			   TPS65218_ENABLE1_DC1_EN, 0, 0, dcdc1_dcdc2_ranges,
+			   2, 4000, 0),
+	TPS65218_REGULATOR("DCDC2", TPS65218_DCDC_2, REGULATOR_VOLTAGE,
+			   tps65218_dcdc12_ops, 64, TPS65218_REG_CONTROL_DCDC2,
+			   TPS65218_CONTROL_DCDC2_MASK, TPS65218_REG_ENABLE1,
+			   TPS65218_ENABLE1_DC2_EN, 0, 0, dcdc1_dcdc2_ranges,
+			   2, 4000, 0),
+	TPS65218_REGULATOR("DCDC3", TPS65218_DCDC_3, REGULATOR_VOLTAGE,
+			   tps65218_ldo1_dcdc34_ops, 64,
+			   TPS65218_REG_CONTROL_DCDC3,
 			   TPS65218_CONTROL_DCDC3_MASK, TPS65218_REG_ENABLE1,
-			   TPS65218_ENABLE1_DC3_EN, ldo1_dcdc3_ranges, 2, 0, 0),
-	TPS65218_REGULATOR("DCDC4", TPS65218_DCDC_4, tps65218_ldo1_dcdc34_ops,
-			   53, TPS65218_REG_CONTROL_DCDC4,
-			   TPS65218_CONTROL_DCDC4_MASK,
-			   TPS65218_REG_ENABLE1, TPS65218_ENABLE1_DC4_EN,
-			   dcdc4_ranges, 2, 0, 0),
-	TPS65218_REGULATOR("DCDC5", TPS65218_DCDC_5, tps65218_dcdc56_pmic_ops,
-			   1, -1, -1, TPS65218_REG_ENABLE1,
-			   TPS65218_ENABLE1_DC5_EN, NULL, 0, 0, 1000000),
-	TPS65218_REGULATOR("DCDC6", TPS65218_DCDC_6, tps65218_dcdc56_pmic_ops,
-			   1, -1, -1, TPS65218_REG_ENABLE1,
-			   TPS65218_ENABLE1_DC6_EN, NULL, 0, 0, 1800000),
-	TPS65218_REGULATOR("LDO1", TPS65218_LDO_1, tps65218_ldo1_dcdc34_ops, 64,
+			   TPS65218_ENABLE1_DC3_EN, 0, 0, ldo1_dcdc3_ranges, 2,
+			   0, 0),
+	TPS65218_REGULATOR("DCDC4", TPS65218_DCDC_4, REGULATOR_VOLTAGE,
+			   tps65218_ldo1_dcdc34_ops, 53,
+			   TPS65218_REG_CONTROL_DCDC4,
+			   TPS65218_CONTROL_DCDC4_MASK, TPS65218_REG_ENABLE1,
+			   TPS65218_ENABLE1_DC4_EN, 0, 0, dcdc4_ranges, 2,
+			   0, 0),
+	TPS65218_REGULATOR("DCDC5", TPS65218_DCDC_5, REGULATOR_VOLTAGE,
+			   tps65218_dcdc56_pmic_ops, 1, -1, -1,
+			   TPS65218_REG_ENABLE1, TPS65218_ENABLE1_DC5_EN, 0, 0,
+			   NULL, 0, 0, 1000000),
+	TPS65218_REGULATOR("DCDC6", TPS65218_DCDC_6, REGULATOR_VOLTAGE,
+			   tps65218_dcdc56_pmic_ops, 1, -1, -1,
+			   TPS65218_REG_ENABLE1, TPS65218_ENABLE1_DC6_EN, 0, 0,
+			   NULL, 0, 0, 1800000),
+	TPS65218_REGULATOR("LDO1", TPS65218_LDO_1, REGULATOR_VOLTAGE,
+			   tps65218_ldo1_dcdc34_ops, 64,
 			   TPS65218_REG_CONTROL_LDO1,
 			   TPS65218_CONTROL_LDO1_MASK, TPS65218_REG_ENABLE2,
-			   TPS65218_ENABLE2_LDO1_EN, ldo1_dcdc3_ranges,
+			   TPS65218_ENABLE2_LDO1_EN, 0, 0, ldo1_dcdc3_ranges,
 			   2, 0, 0),
+	TPS65218_REGULATOR("LS3", TPS65218_LS_3, REGULATOR_CURRENT,
+			   tps65218_ls3_ops, 0, 0, 0, TPS65218_REG_ENABLE2,
+			   TPS65218_ENABLE2_LS3_EN, TPS65218_REG_CONFIG2,
+			   TPS65218_CONFIG2_LS3ILIM_MASK, NULL, 0, 0, 0),
 };
 
 static int tps65218_regulator_probe(struct platform_device *pdev)

include/linux/mfd/tps65218.h

@@ -200,6 +200,8 @@ enum tps65218_regulator_id {
 	TPS65218_DCDC_4,
 	TPS65218_DCDC_5,
 	TPS65218_DCDC_6,
+	/* LS's */
+	TPS65218_LS_3,
 	/* LDOs */
 	TPS65218_LDO_1,
 };
@@ -210,8 +212,11 @@ enum tps65218_regulator_id {
 #define TPS65218_NUM_DCDC		6
 /* Number of LDO voltage regulators available */
 #define TPS65218_NUM_LDO		1
+/* Number of total LS current regulators available */
+#define TPS65218_NUM_LS			1
 /* Number of total regulators available */
-#define TPS65218_NUM_REGULATOR		(TPS65218_NUM_DCDC + TPS65218_NUM_LDO)
+#define TPS65218_NUM_REGULATOR		(TPS65218_NUM_DCDC + TPS65218_NUM_LDO \
+					 + TPS65218_NUM_LS)
 
 /* Define the TPS65218 IRQ numbers */
 enum tps65218_irqs {

include/linux/regulator/driver.h

@@ -302,6 +302,8 @@ struct regulator_desc {
 
 	unsigned int vsel_reg;
 	unsigned int vsel_mask;
+	unsigned int csel_reg;
+	unsigned int csel_mask;
 	unsigned int apply_reg;
 	unsigned int apply_bit;
 	unsigned int enable_reg;