Commit 797149d0 authored by David S. Miller's avatar David S. Miller

Merge branch 'stmmac-DMA-burst'

Niklas Cassel says:

====================
net: stmmac: make DMA programmable burst length more configurable

Make DMA programmable burst length more configurable in the stmmac driver.

This is done by adding support for independent pbl for tx/rx through DT.
More fine grained tuning of pbl is possible thanks to a DT property saying
that we should NOT multiply pbl values by x8/x4 in hardware.

All new DT properties are optional, and created in a way that it will not
affect any existing DT configurations.

Changes since V1:
Created cover-letter.
Rebased patch set against next-20161205, since conflicting patches to
stmmac_platform.c has been merged since V1.

Changes since V2:
Moved default value initialization of pbl to stmmac_platform.c
and added a check for pbl != 0 in stmmac_main.c,
to catch a possble pbl == 0 from pci glue.
====================
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parents 3f0dd6b7 4022d039
......@@ -34,7 +34,13 @@ Optional properties:
platforms.
- tx-fifo-depth: See ethernet.txt file in the same directory
- rx-fifo-depth: See ethernet.txt file in the same directory
- snps,pbl Programmable Burst Length
- snps,pbl Programmable Burst Length (tx and rx)
- snps,txpbl Tx Programmable Burst Length. Only for GMAC and newer.
If set, DMA tx will use this value rather than snps,pbl.
- snps,rxpbl Rx Programmable Burst Length. Only for GMAC and newer.
If set, DMA rx will use this value rather than snps,pbl.
- snps,no-pbl-x8 Don't multiply the pbl/txpbl/rxpbl values by 8.
For core rev < 3.50, don't multiply the values by 4.
- snps,aal Address-Aligned Beats
- snps,fixed-burst Program the DMA to use the fixed burst mode
- snps,mixed-burst Program the DMA to use the mixed burst mode
......
......@@ -152,8 +152,10 @@ Where:
o dma_cfg: internal DMA parameters
o pbl: the Programmable Burst Length is maximum number of beats to
be transferred in one DMA transaction.
GMAC also enables the 4xPBL by default.
o fixed_burst/mixed_burst/burst_len
GMAC also enables the 4xPBL by default. (8xPBL for GMAC 3.50 and newer)
o txpbl/rxpbl: GMAC and newer supports independent DMA pbl for tx/rx.
o pblx8: Enable 8xPBL (4xPBL for core rev < 3.50). Enabled by default.
o fixed_burst/mixed_burst/aal
o clk_csr: fixed CSR Clock range selection.
o has_gmac: uses the GMAC core.
o enh_desc: if sets the MAC will use the enhanced descriptor structure.
......@@ -205,16 +207,24 @@ tuned according to the HW capabilities.
struct stmmac_dma_cfg {
int pbl;
int txpbl;
int rxpbl;
bool pblx8;
int fixed_burst;
int burst_len_supported;
int mixed_burst;
bool aal;
};
Where:
o pbl: Programmable Burst Length
o pbl: Programmable Burst Length (tx and rx)
o txpbl: Transmit Programmable Burst Length. Only for GMAC and newer.
If set, DMA tx will use this value rather than pbl.
o rxpbl: Receive Programmable Burst Length. Only for GMAC and newer.
If set, DMA rx will use this value rather than pbl.
o pblx8: Enable 8xPBL (4xPBL for core rev < 3.50). Enabled by default.
o fixed_burst: program the DMA to use the fixed burst mode
o burst_len: this is the value we put in the register
supported values are provided as macros in
linux/stmmac.h header file.
o mixed_burst: program the DMA to use the mixed burst mode
o aal: Address-Aligned Beats
---
......
......@@ -412,8 +412,8 @@ extern const struct stmmac_desc_ops ndesc_ops;
struct stmmac_dma_ops {
/* DMA core initialization */
int (*reset)(void __iomem *ioaddr);
void (*init)(void __iomem *ioaddr, int pbl, int fb, int mb,
int aal, u32 dma_tx, u32 dma_rx, int atds);
void (*init)(void __iomem *ioaddr, struct stmmac_dma_cfg *dma_cfg,
u32 dma_tx, u32 dma_rx, int atds);
/* Configure the AXI Bus Mode Register */
void (*axi)(void __iomem *ioaddr, struct stmmac_axi *axi);
/* Dump DMA registers */
......
......@@ -225,7 +225,7 @@ enum rx_tx_priority_ratio {
#define DMA_BUS_MODE_FB 0x00010000 /* Fixed burst */
#define DMA_BUS_MODE_MB 0x04000000 /* Mixed burst */
#define DMA_BUS_MODE_RPBL_MASK 0x003e0000 /* Rx-Programmable Burst Len */
#define DMA_BUS_MODE_RPBL_MASK 0x007e0000 /* Rx-Programmable Burst Len */
#define DMA_BUS_MODE_RPBL_SHIFT 17
#define DMA_BUS_MODE_USP 0x00800000
#define DMA_BUS_MODE_MAXPBL 0x01000000
......
......@@ -84,37 +84,39 @@ static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi)
writel(value, ioaddr + DMA_AXI_BUS_MODE);
}
static void dwmac1000_dma_init(void __iomem *ioaddr, int pbl, int fb, int mb,
int aal, u32 dma_tx, u32 dma_rx, int atds)
static void dwmac1000_dma_init(void __iomem *ioaddr,
struct stmmac_dma_cfg *dma_cfg,
u32 dma_tx, u32 dma_rx, int atds)
{
u32 value = readl(ioaddr + DMA_BUS_MODE);
int txpbl = dma_cfg->txpbl ?: dma_cfg->pbl;
int rxpbl = dma_cfg->rxpbl ?: dma_cfg->pbl;
/*
* Set the DMA PBL (Programmable Burst Length) mode.
*
* Note: before stmmac core 3.50 this mode bit was 4xPBL, and
* post 3.5 mode bit acts as 8*PBL.
*
* This configuration doesn't take care about the Separate PBL
* so only the bits: 13-8 are programmed with the PBL passed from the
* platform.
*/
if (dma_cfg->pblx8)
value |= DMA_BUS_MODE_MAXPBL;
value &= ~DMA_BUS_MODE_PBL_MASK;
value |= (pbl << DMA_BUS_MODE_PBL_SHIFT);
value |= DMA_BUS_MODE_USP;
value &= ~(DMA_BUS_MODE_PBL_MASK | DMA_BUS_MODE_RPBL_MASK);
value |= (txpbl << DMA_BUS_MODE_PBL_SHIFT);
value |= (rxpbl << DMA_BUS_MODE_RPBL_SHIFT);
/* Set the Fixed burst mode */
if (fb)
if (dma_cfg->fixed_burst)
value |= DMA_BUS_MODE_FB;
/* Mixed Burst has no effect when fb is set */
if (mb)
if (dma_cfg->mixed_burst)
value |= DMA_BUS_MODE_MB;
if (atds)
value |= DMA_BUS_MODE_ATDS;
if (aal)
if (dma_cfg->aal)
value |= DMA_BUS_MODE_AAL;
writel(value, ioaddr + DMA_BUS_MODE);
......
......@@ -32,11 +32,12 @@
#include "dwmac100.h"
#include "dwmac_dma.h"
static void dwmac100_dma_init(void __iomem *ioaddr, int pbl, int fb, int mb,
int aal, u32 dma_tx, u32 dma_rx, int atds)
static void dwmac100_dma_init(void __iomem *ioaddr,
struct stmmac_dma_cfg *dma_cfg,
u32 dma_tx, u32 dma_rx, int atds)
{
/* Enable Application Access by writing to DMA CSR0 */
writel(DMA_BUS_MODE_DEFAULT | (pbl << DMA_BUS_MODE_PBL_SHIFT),
writel(DMA_BUS_MODE_DEFAULT | (dma_cfg->pbl << DMA_BUS_MODE_PBL_SHIFT),
ioaddr + DMA_BUS_MODE);
/* Mask interrupts by writing to CSR7 */
......
......@@ -71,25 +71,29 @@ static void dwmac4_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi)
writel(value, ioaddr + DMA_SYS_BUS_MODE);
}
static void dwmac4_dma_init_channel(void __iomem *ioaddr, int pbl,
static void dwmac4_dma_init_channel(void __iomem *ioaddr,
struct stmmac_dma_cfg *dma_cfg,
u32 dma_tx_phy, u32 dma_rx_phy,
u32 channel)
{
u32 value;
int txpbl = dma_cfg->txpbl ?: dma_cfg->pbl;
int rxpbl = dma_cfg->rxpbl ?: dma_cfg->pbl;
/* set PBL for each channels. Currently we affect same configuration
* on each channel
*/
value = readl(ioaddr + DMA_CHAN_CONTROL(channel));
if (dma_cfg->pblx8)
value = value | DMA_BUS_MODE_PBL;
writel(value, ioaddr + DMA_CHAN_CONTROL(channel));
value = readl(ioaddr + DMA_CHAN_TX_CONTROL(channel));
value = value | (pbl << DMA_BUS_MODE_PBL_SHIFT);
value = value | (txpbl << DMA_BUS_MODE_PBL_SHIFT);
writel(value, ioaddr + DMA_CHAN_TX_CONTROL(channel));
value = readl(ioaddr + DMA_CHAN_RX_CONTROL(channel));
value = value | (pbl << DMA_BUS_MODE_RPBL_SHIFT);
value = value | (rxpbl << DMA_BUS_MODE_RPBL_SHIFT);
writel(value, ioaddr + DMA_CHAN_RX_CONTROL(channel));
/* Mask interrupts by writing to CSR7 */
......@@ -99,27 +103,28 @@ static void dwmac4_dma_init_channel(void __iomem *ioaddr, int pbl,
writel(dma_rx_phy, ioaddr + DMA_CHAN_RX_BASE_ADDR(channel));
}
static void dwmac4_dma_init(void __iomem *ioaddr, int pbl, int fb, int mb,
int aal, u32 dma_tx, u32 dma_rx, int atds)
static void dwmac4_dma_init(void __iomem *ioaddr,
struct stmmac_dma_cfg *dma_cfg,
u32 dma_tx, u32 dma_rx, int atds)
{
u32 value = readl(ioaddr + DMA_SYS_BUS_MODE);
int i;
/* Set the Fixed burst mode */
if (fb)
if (dma_cfg->fixed_burst)
value |= DMA_SYS_BUS_FB;
/* Mixed Burst has no effect when fb is set */
if (mb)
if (dma_cfg->mixed_burst)
value |= DMA_SYS_BUS_MB;
if (aal)
if (dma_cfg->aal)
value |= DMA_SYS_BUS_AAL;
writel(value, ioaddr + DMA_SYS_BUS_MODE);
for (i = 0; i < DMA_CHANNEL_NB_MAX; i++)
dwmac4_dma_init_channel(ioaddr, pbl, dma_tx, dma_rx, i);
dwmac4_dma_init_channel(ioaddr, dma_cfg, dma_tx, dma_rx, i);
}
static void _dwmac4_dump_dma_regs(void __iomem *ioaddr, u32 channel)
......
......@@ -1578,16 +1578,12 @@ static void stmmac_check_ether_addr(struct stmmac_priv *priv)
*/
static int stmmac_init_dma_engine(struct stmmac_priv *priv)
{
int pbl = DEFAULT_DMA_PBL, fixed_burst = 0, aal = 0;
int mixed_burst = 0;
int atds = 0;
int ret = 0;
if (priv->plat->dma_cfg) {
pbl = priv->plat->dma_cfg->pbl;
fixed_burst = priv->plat->dma_cfg->fixed_burst;
mixed_burst = priv->plat->dma_cfg->mixed_burst;
aal = priv->plat->dma_cfg->aal;
if (!priv->plat->dma_cfg || !priv->plat->dma_cfg->pbl) {
dev_err(priv->device, "Invalid DMA configuration\n");
return -EINVAL;
}
if (priv->extend_desc && (priv->mode == STMMAC_RING_MODE))
......@@ -1599,8 +1595,8 @@ static int stmmac_init_dma_engine(struct stmmac_priv *priv)
return ret;
}
priv->hw->dma->init(priv->ioaddr, pbl, fixed_burst, mixed_burst,
aal, priv->dma_tx_phy, priv->dma_rx_phy, atds);
priv->hw->dma->init(priv->ioaddr, priv->plat->dma_cfg,
priv->dma_tx_phy, priv->dma_rx_phy, atds);
if (priv->synopsys_id >= DWMAC_CORE_4_00) {
priv->rx_tail_addr = priv->dma_rx_phy +
......
......@@ -81,6 +81,7 @@ static void stmmac_default_data(struct plat_stmmacenet_data *plat)
plat->mdio_bus_data->phy_mask = 0;
plat->dma_cfg->pbl = 32;
plat->dma_cfg->pblx8 = true;
/* TODO: AXI */
/* Set default value for multicast hash bins */
......@@ -115,6 +116,7 @@ static int quark_default_data(struct plat_stmmacenet_data *plat,
plat->mdio_bus_data->phy_mask = 0;
plat->dma_cfg->pbl = 16;
plat->dma_cfg->pblx8 = true;
plat->dma_cfg->fixed_burst = 1;
/* AXI (TODO) */
......
......@@ -304,7 +304,6 @@ stmmac_probe_config_dt(struct platform_device *pdev, const char **mac)
plat->force_sf_dma_mode = 1;
}
if (of_find_property(np, "snps,pbl", NULL)) {
dma_cfg = devm_kzalloc(&pdev->dev, sizeof(*dma_cfg),
GFP_KERNEL);
if (!dma_cfg) {
......@@ -312,13 +311,18 @@ stmmac_probe_config_dt(struct platform_device *pdev, const char **mac)
return ERR_PTR(-ENOMEM);
}
plat->dma_cfg = dma_cfg;
of_property_read_u32(np, "snps,pbl", &dma_cfg->pbl);
if (!dma_cfg->pbl)
dma_cfg->pbl = DEFAULT_DMA_PBL;
of_property_read_u32(np, "snps,txpbl", &dma_cfg->txpbl);
of_property_read_u32(np, "snps,rxpbl", &dma_cfg->rxpbl);
dma_cfg->pblx8 = !of_property_read_bool(np, "snps,no-pbl-x8");
dma_cfg->aal = of_property_read_bool(np, "snps,aal");
dma_cfg->fixed_burst =
of_property_read_bool(np, "snps,fixed-burst");
dma_cfg->mixed_burst =
of_property_read_bool(np, "snps,mixed-burst");
}
dma_cfg->fixed_burst = of_property_read_bool(np, "snps,fixed-burst");
dma_cfg->mixed_burst = of_property_read_bool(np, "snps,mixed-burst");
plat->force_thresh_dma_mode = of_property_read_bool(np, "snps,force_thresh_dma_mode");
if (plat->force_thresh_dma_mode) {
plat->force_sf_dma_mode = 0;
......
......@@ -88,6 +88,9 @@ struct stmmac_mdio_bus_data {
struct stmmac_dma_cfg {
int pbl;
int txpbl;
int rxpbl;
bool pblx8;
int fixed_burst;
int mixed_burst;
bool aal;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment