Merge tag 'omap-for-v4.7-dts-fixes1' of...

Merge tag 'omap-for-v4.7-dts-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

DTS fixes for omaps for v4.7 merge window for issues noted
with patches in Linux next:

- Fix omap5 and am57xx-idk input voltages to fix micro-sd
  probing at least for some omap5-uevm configurations

- Fix unhandled fault for igepv5 audio

- Fix UART wakeirqs for omap5 by removing WAKUP_EN flags,
  those are managed by the wakeirq and can currently confuse
  the wakeirqs as there is no handler necessarily registered

- Fix LDO7 source for igepv5

Also included are few minor changes not strictly fixes
are good to have merged:

- Fix HP T410 boot time warnings for eMMC and disable the
  unused MMC interfaces while at it

- Add dra7 gpmc dma channel

- Add igep00x0 SD card detect and write protect GPIOs

* tag 'omap-for-v4.7-dts-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: igep0020: Add SD card write-protect pin.
  ARM: dts: igep00x0: Add SD card-detect.
  ARM: dts: am57xx-idk-common: Fix input supply names
  ARM: dts: dra7: Add gpmc dma channel
  ARM: dts: disable mmc by default and enable when needed for dm814x
  ARM: dts: Add non-removable to hsmmc on hp-t410
  ARM: dts: Fix ldo7 source for HDMI on igepv5
  ARM: dts: Fix uart wakeirq on omap5 by removing WAKEUP_EN for omaps
  ARM: dts: Fix igepv5 audiopwon-gpio
  ARM: dts: omap5-board-common: Describe the voltage supply mapping accurately
Signed-off-by: Olof Johansson <olof@lixom.net>

arch/arm/boot/dts/am57xx-idk-common.dtsi

@@ -60,10 +60,26 @@ tps659038: tps659038@58 {
 
 		tps659038_pmic {
 			compatible = "ti,tps659038-pmic";
+
+			smps12-in-supply = <&vmain>;
+			smps3-in-supply = <&vmain>;
+			smps45-in-supply = <&vmain>;
+			smps6-in-supply = <&vmain>;
+			smps7-in-supply = <&vmain>;
+			smps8-in-supply = <&vmain>;
+			smps9-in-supply = <&vmain>;
+			ldo1-in-supply = <&vmain>;
+			ldo2-in-supply = <&vmain>;
+			ldo3-in-supply = <&vmain>;
+			ldo4-in-supply = <&vmain>;
+			ldo9-in-supply = <&vmain>;
+			ldoln-in-supply = <&vmain>;
+			ldousb-in-supply = <&vmain>;
+			ldortc-in-supply = <&vmain>;
+
 			regulators {
 				smps12_reg: smps12 {
 					/* VDD_MPU */
-					vin-supply = <&vmain>;
 					regulator-name = "smps12";
 					regulator-min-microvolt = <850000>;
 					regulator-max-microvolt = <1250000>;
@@ -73,7 +89,6 @@ smps12_reg: smps12 {
 
 				smps3_reg: smps3 {
 					/* VDD_DDR EMIF1 EMIF2 */
-					vin-supply = <&vmain>;
 					regulator-name = "smps3";
 					regulator-min-microvolt = <1350000>;
 					regulator-max-microvolt = <1350000>;
@@ -84,7 +99,6 @@ smps3_reg: smps3 {
 				smps45_reg: smps45 {
 					/* VDD_DSPEVE on AM572 */
 					/* VDD_IVA + VDD_DSP on AM571 */
-					vin-supply = <&vmain>;
 					regulator-name = "smps45";
 					regulator-min-microvolt = <850000>;
 					regulator-max-microvolt = <1250000>;
@@ -94,7 +108,6 @@ smps45_reg: smps45 {
 
 				smps6_reg: smps6 {
 					/* VDD_GPU */
-					vin-supply = <&vmain>;
 					regulator-name = "smps6";
 					regulator-min-microvolt = <850000>;
 					regulator-max-microvolt = <1250000>;
@@ -104,7 +117,6 @@ smps6_reg: smps6 {
 
 				smps7_reg: smps7 {
 					/* VDD_CORE */
-					vin-supply = <&vmain>;
 					regulator-name = "smps7";
 					regulator-min-microvolt = <850000>;
 					regulator-max-microvolt = <1150000>;
@@ -115,13 +127,11 @@ smps7_reg: smps7 {
 				smps8_reg: smps8 {
 					/* 5728 - VDD_IVAHD */
 					/* 5718 - N.C. test point */
-					vin-supply = <&vmain>;
 					regulator-name = "smps8";
 				};
 
 				smps9_reg: smps9 {
 					/* VDD_3_3D */
-					vin-supply = <&vmain>;
 					regulator-name = "smps9";
 					regulator-min-microvolt = <3300000>;
 					regulator-max-microvolt = <3300000>;
@@ -132,7 +142,6 @@ smps9_reg: smps9 {
 				ldo1_reg: ldo1 {
 					/* VDDSHV8 - VSDMMC  */
 					/* NOTE: on rev 1.3a, data supply */
-					vin-supply = <&vmain>;
 					regulator-name = "ldo1";
 					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <3300000>;
@@ -142,7 +151,6 @@ ldo1_reg: ldo1 {
 
 				ldo2_reg: ldo2 {
 					/* VDDSH18V */
-					vin-supply = <&vmain>;
 					regulator-name = "ldo2";
 					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <1800000>;
@@ -152,7 +160,6 @@ ldo2_reg: ldo2 {
 
 				ldo3_reg: ldo3 {
 					/* R1.3a 572x V1_8PHY_LDO3: USB, SATA */
-					vin-supply = <&vmain>;
 					regulator-name = "ldo3";
 					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <1800000>;
@@ -162,7 +169,6 @@ ldo3_reg: ldo3 {
 
 				ldo4_reg: ldo4 {
 					/* R1.3a 572x V1_8PHY_LDO4: PCIE, HDMI*/
-					vin-supply = <&vmain>;
 					regulator-name = "ldo4";
 					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <1800000>;
@@ -174,7 +180,6 @@ ldo4_reg: ldo4 {
 
 				ldo9_reg: ldo9 {
 					/* VDD_RTC  */
-					vin-supply = <&vmain>;
 					regulator-name = "ldo9";
 					regulator-min-microvolt = <840000>;
 					regulator-max-microvolt = <1160000>;
@@ -184,7 +189,6 @@ ldo9_reg: ldo9 {
 
 				ldoln_reg: ldoln {
 					/* VDDA_1V8_PLL */
-					vin-supply = <&vmain>;
 					regulator-name = "ldoln";
 					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <1800000>;
@@ -194,7 +198,6 @@ ldoln_reg: ldoln {
 
 				ldousb_reg: ldousb {
 					/* VDDA_3V_USB: VDDA_USBHS33 */
-					vin-supply = <&vmain>;
 					regulator-name = "ldousb";
 					regulator-min-microvolt = <3300000>;
 					regulator-max-microvolt = <3300000>;
@@ -204,7 +207,6 @@ ldousb_reg: ldousb {
 
 				ldortc_reg: ldortc {
 					/* VDDA_RTC  */
-					vin-supply = <&vmain>;
 					regulator-name = "ldortc";
 					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <1800000>;

arch/arm/boot/dts/dm8148-evm.dts

@@ -93,6 +93,10 @@ partition@0x780000 {
 	};
 };
 
+&mmc1 {
+        status = "disabled";
+};
+
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&sd1_pins>;
@@ -101,6 +105,10 @@ &mmc2 {
 	cd-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
 };
 
+&mmc3 {
+        status = "disabled";
+};
+
 &pincntl {
 	sd1_pins: pinmux_sd1_pins {
 		pinctrl-single,pins = <

arch/arm/boot/dts/dm8148-t410.dts

@@ -45,6 +45,14 @@ &cpsw_emac1 {
 	phy-mode = "rgmii";
 };
 
+&mmc1 {
+	status = "disabled";
+};
+
+&mmc2 {
+	status = "disabled";
+};
+
 &mmc3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&sd2_pins>;
@@ -53,6 +61,7 @@ &mmc3 {
 	dmas = <&edma_xbar 8 0 1	/* use SDTXEVT1 instead of MCASP0TX */
 		&edma_xbar 9 0 2>;	/* use SDRXEVT1 instead of MCASP0RX */
 	dma-names = "tx", "rx";
+	non-removable;
 };
 
 &pincntl {

arch/arm/boot/dts/dra7.dtsi

@@ -1451,6 +1451,8 @@ gpmc: gpmc@50000000 {
 			ti,hwmods = "gpmc";
 			reg = <0x50000000 0x37c>;      /* device IO registers */
 			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&edma_xbar 4 0>;
+			dma-names = "rxtx";
 			gpmc,num-cs = <8>;
 			gpmc,num-waitpins = <2>;
 			#address-cells = <2>;

arch/arm/boot/dts/omap3-evm-37xx.dts

@@ -85,7 +85,7 @@ mmc2_pins: pinmux_mmc2_pins {
 			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
 			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
 			OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat0.sdmmc2_dat0 */
-			OMAP3_CORE1_IOPAD(0x215e, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
+			OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
 			OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2.sdmmc2_dat2 */
 			OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3.sdmmc2_dat3 */
 		>;

arch/arm/boot/dts/omap3-igep.dtsi

@@ -188,6 +188,7 @@ &mmc1 {
 	vmmc-supply = <&vmmc1>;
 	vmmc_aux-supply = <&vsim>;
 	bus-width = <4>;
+	cd-gpios = <&twl_gpio 0 GPIO_ACTIVE_LOW>;
 };
 
 &mmc3 {

arch/arm/boot/dts/omap3-igep0020-common.dtsi

@@ -194,6 +194,12 @@ OMAP3630_CORE2_IOPAD(0x25f6, PIN_OUTPUT | MUX_MODE4) /* etk_d13.gpio_27 */
 			OMAP3630_CORE2_IOPAD(0x25f8, PIN_OUTPUT | MUX_MODE4) /* etk_d14.gpio_28 */
 		>;
 	};
+
+	mmc1_wp_pins: pinmux_mmc1_cd_pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT | MUX_MODE4)   /* etk_d15.gpio_29 */
+		>;
+	};
 };
 
 &i2c3 {
@@ -250,3 +256,8 @@ dpi_out: endpoint {
 		};
 	};
 };
+
+&mmc1 {
+	pinctrl-0 = <&mmc1_pins &mmc1_wp_pins>;
+	wp-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;	/* gpio_29 */
+};

arch/arm/boot/dts/omap3-n900.dts

@@ -288,7 +288,7 @@ ssi_pins: pinmux_ssi {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT_PULLUP | MUX_MODE1)	/* ssi1_rdy_tx */
 			OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE1)		/* ssi1_flag_tx */
-			OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* ssi1_wake_tx (cawake) */
+			OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | MUX_MODE4)		/* ssi1_wake_tx (cawake) */
 			OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE1)		/* ssi1_dat_tx */
 			OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT | MUX_MODE1)		/* ssi1_dat_rx */
 			OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE1)		/* ssi1_flag_rx */
@@ -300,7 +300,7 @@ OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | MUX_MODE1)		/* ssi1_wake */
 	modem_pins: pinmux_modem {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE4)		/* gpio 70 => cmt_apeslpx */
-			OMAP3_CORE1_IOPAD(0x20e0, PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* gpio 72 => ape_rst_rq */
+			OMAP3_CORE1_IOPAD(0x20e0, PIN_INPUT | MUX_MODE4)		/* gpio 72 => ape_rst_rq */
 			OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE4)		/* gpio 73 => cmt_rst_rq */
 			OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE4)		/* gpio 74 => cmt_en */
 			OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE4)		/* gpio 75 => cmt_rst */

arch/arm/boot/dts/omap3-n950-n9.dtsi

@@ -97,7 +97,7 @@ ssi_pins: pinmux_ssi_pins {
 			OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE1)            /* ssi1_dat_tx */
 			OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE1)            /* ssi1_flag_tx */
 			OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT_PULLUP | MUX_MODE1)      /* ssi1_rdy_tx */
-			OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* ssi1_wake_tx (cawake) */
+			OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | MUX_MODE4)	/* ssi1_wake_tx (cawake) */
 			OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT | MUX_MODE1)             /* ssi1_dat_rx */
 			OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE1)             /* ssi1_flag_rx */
 			OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | MUX_MODE1)            /* ssi1_rdy_rx */
@@ -110,7 +110,7 @@ ssi_pins_idle: pinmux_ssi_pins_idle {
 			OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE7)            /* ssi1_dat_tx */
 			OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE7)            /* ssi1_flag_tx */
 			OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT_PULLDOWN | MUX_MODE7)    /* ssi1_rdy_tx */
-			OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* ssi1_wake_tx (cawake) */
+			OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | MUX_MODE4)	/* ssi1_wake_tx (cawake) */
 			OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT | MUX_MODE7)             /* ssi1_dat_rx */
 			OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE7)             /* ssi1_flag_rx */
 			OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | MUX_MODE4)            /* ssi1_rdy_rx */
@@ -120,7 +120,7 @@ OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | MUX_MODE7)            /* ssi1_wake */
 
 	modem_pins1: pinmux_modem_core1_pins {
 		pinctrl-single,pins = <
-			OMAP3_CORE1_IOPAD(0x207a, PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* gpio_34 (ape_rst_rq) */
+			OMAP3_CORE1_IOPAD(0x207a, PIN_INPUT | MUX_MODE4)	/* gpio_34 (ape_rst_rq) */
 			OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE4)            /* gpio_88 (cmt_rst_rq) */
 			OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE4)            /* gpio_93 (cmt_apeslpx) */
 		>;

arch/arm/boot/dts/omap3-zoom3.dts

@@ -98,7 +98,7 @@ uart2_pins: pinmux_uart2_pins {
 		pinctrl-single,pins = <
                         OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart2_cts.uart2_cts */
                         OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0)		/* uart2_rts.uart2_rts */
-                        OMAP3_CORE1_IOPAD(0x217a, WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */
+                        OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0)		/* uart2_rx.uart2_rx */
                         OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0)		/* uart2_tx.uart2_tx */
 		>;
 	};
@@ -107,7 +107,7 @@ uart3_pins: pinmux_uart3_pins {
 		pinctrl-single,pins = <
                         OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* uart3_cts_rctx.uart3_cts_rctx */
                         OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE0)		/* uart3_rts_sd.uart3_rts_sd */
-                        OMAP3_CORE1_IOPAD(0x219e, WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
+                        OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0)		/* uart3_rx_irrx.uart3_rx_irrx */
                         OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)		/* uart3_tx_irtx.uart3_tx_irtx */
 		>;
 	};
@@ -125,7 +125,7 @@ mmc3_2_pins: pinmux_mmc3_2_pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_clk.sdmmc3_clk */
 			OMAP3630_CORE2_IOPAD(0x25e4, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d4.sdmmc3_dat0 */
-			OMAP3630_CORE2_IOPAD(0x25e6, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d5.sdmmc3_dat1 */
+			OMAP3630_CORE2_IOPAD(0x25e6, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d5.sdmmc3_dat1 */
 			OMAP3630_CORE2_IOPAD(0x25e8, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d6.sdmmc3_dat2 */
 			OMAP3630_CORE2_IOPAD(0x25e2, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d3.sdmmc3_dat3 */
 		>;

arch/arm/boot/dts/omap5-board-common.dtsi

@@ -14,6 +14,29 @@ aliases {
 		display0 = &hdmi0;
 	};
 
+	vmain: fixedregulator-vmain {
+		compatible = "regulator-fixed";
+		regulator-name = "vmain";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vsys_cobra: fixedregulator-vsys_cobra {
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_cobra";
+		vin-supply = <&vmain>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vdds_1v8_main: fixedregulator-vdds_1v8_main {
+		compatible = "regulator-fixed";
+		regulator-name = "vdds_1v8_main";
+		vin-supply = <&smps7_reg>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
 	vmmcsd_fixed: fixedregulator-mmcsd {
 		compatible = "regulator-fixed";
 		regulator-name = "vmmcsd_fixed";
@@ -309,7 +332,7 @@ OMAP5_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */
 
 	wlcore_irq_pin: pinmux_wlcore_irq_pin {
 		pinctrl-single,pins = <
-			OMAP5_IOPAD(0x40, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE6)	/* llia_wakereqin.gpio1_wk14 */
+			OMAP5_IOPAD(0x40, PIN_INPUT_PULLUP | MUX_MODE6)	/* llia_wakereqin.gpio1_wk14 */
 		>;
 	};
 };
@@ -409,6 +432,26 @@ palmas_pmic {
 
 			ti,ldo6-vibrator;
 
+			smps123-in-supply = <&vsys_cobra>;
+			smps45-in-supply = <&vsys_cobra>;
+			smps6-in-supply = <&vsys_cobra>;
+			smps7-in-supply = <&vsys_cobra>;
+			smps8-in-supply = <&vsys_cobra>;
+			smps9-in-supply = <&vsys_cobra>;
+			smps10_out2-in-supply = <&vsys_cobra>;
+			smps10_out1-in-supply = <&vsys_cobra>;
+			ldo1-in-supply = <&vsys_cobra>;
+			ldo2-in-supply = <&vsys_cobra>;
+			ldo3-in-supply = <&vdds_1v8_main>;
+			ldo4-in-supply = <&vdds_1v8_main>;
+			ldo5-in-supply = <&vsys_cobra>;
+			ldo6-in-supply = <&vdds_1v8_main>;
+			ldo7-in-supply = <&vsys_cobra>;
+			ldo8-in-supply = <&vsys_cobra>;
+			ldo9-in-supply = <&vmmcsd_fixed>;
+			ldoln-in-supply = <&vsys_cobra>;
+			ldousb-in-supply = <&vsys_cobra>;
+
 			regulators {
 				smps123_reg: smps123 {
 					/* VDD_OPP_MPU */
@@ -600,7 +643,8 @@ twl6040: twl@4b {
 		pinctrl-0 = <&twl6040_pins>;
 
 		interrupts = <GIC_SPI 119 IRQ_TYPE_NONE>; /* IRQ_SYS_2N cascaded to gic */
-		ti,audpwron-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>;  /* gpio line 141 */
+
+		/* audpwron gpio defined in the board specific dts */
 
 		vio-supply = <&smps7_reg>;
 		v2v1-supply = <&smps9_reg>;

arch/arm/boot/dts/omap5-igep0050.dts

@@ -35,6 +35,22 @@ tca6416: tca6416@21 {
 	};
 };
 
+/* LDO4 is VPP1 - ball AD9 */
+&ldo4_reg {
+	regulator-min-microvolt = <2000000>;
+	regulator-max-microvolt = <2000000>;
+};
+
+/*
+ * LDO7 is used for HDMI: VDDA_DSIPORTA - ball AA33, VDDA_DSIPORTC - ball AE33,
+ * VDDA_HDMI - ball AN25
+ */
+&ldo7_reg {
+	status = "okay";
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+};
+
 &omap5_pmx_core {
 	i2c4_pins: pinmux_i2c4_pins {
 		pinctrl-single,pins = <
@@ -52,3 +68,13 @@ &tpd12s015 {
 		<&gpio7 3 0>;		/* 195, SDA */
 };
 
+&twl6040 {
+	ti,audpwron-gpio = <&gpio5 16 GPIO_ACTIVE_HIGH>;  /* gpio line 144 */
+};
+
+&twl6040_pins {
+	pinctrl-single,pins = <
+		OMAP5_IOPAD(0x1c4, PIN_OUTPUT | MUX_MODE6)	/* mcspi1_somi.gpio5_144 */
+		OMAP5_IOPAD(0x1ca, PIN_OUTPUT | MUX_MODE6)	/* perslimbus2_clock.gpio5_145 */
+	>;
+};

arch/arm/boot/dts/omap5-uevm.dts

@@ -51,3 +51,13 @@ &tpd12s015 {
 		<&gpio9 1 GPIO_ACTIVE_HIGH>,	/* TCA6424A P00, LS OE */
 		<&gpio7 1 GPIO_ACTIVE_HIGH>;	/* GPIO 193, HPD */
 };
+
+&twl6040 {
+	ti,audpwron-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>;  /* gpio line 141 */
+};
+
+&twl6040_pins {
+	pinctrl-single,pins = <
+		OMAP5_IOPAD(0x1be, PIN_OUTPUT | MUX_MODE6)	/* mcspi1_somi.gpio5_141 */
+	>;
+};