ath9k: remove ->config_pci_powersave() redundant argument

We always call ->config_pci_powersave() with both restore and power_off
arguments equal to 0 or both equal to 1, so merge them into one
argument.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath/ath9k/ar9002_hw.c

@@ -303,8 +303,7 @@ static void ar9002_hw_init_mode_gain_regs(struct ath_hw *ah)
  * register as the other analog registers.  Hence the 9 writes.
  */
 static void ar9002_hw_configpcipowersave(struct ath_hw *ah,
-					 int restore,
-					 int power_off)
+					 bool power_off)
 {
 	u8 i;
 	u32 val;
@@ -313,7 +312,7 @@ static void ar9002_hw_configpcipowersave(struct ath_hw *ah,
 		return;
 
 	/* Nothing to do on restore for 11N */
-	if (!restore) {
+	if (!power_off /* !restore */) {
 		if (AR_SREV_9280_20_OR_LATER(ah)) {
 			/*
 			 * AR9280 2.0 or later chips use SerDes values from the

drivers/net/wireless/ath/ath9k/ar9003_hw.c

@@ -516,14 +516,13 @@ static void ar9003_hw_init_mode_gain_regs(struct ath_hw *ah)
  * register as the other analog registers.  Hence the 9 writes.
  */
 static void ar9003_hw_configpcipowersave(struct ath_hw *ah,
-					 int restore,
-					 int power_off)
+					 bool power_off)
 {
 	if (ah->is_pciexpress != true || ah->aspm_enabled != true)
 		return;
 
 	/* Nothing to do on restore for 11N */
-	if (!restore) {
+	if (!power_off /* !restore */) {
 		/* set bit 19 to allow forcing of pcie core into L1 state */
 		REG_SET_BIT(ah, AR_PCIE_PM_CTRL, AR_PCIE_PM_CTRL_ENA);
 

drivers/net/wireless/ath/ath9k/hw-ops.h

@@ -22,10 +22,9 @@
 /* Hardware core and driver accessible callbacks */
 
 static inline void ath9k_hw_configpcipowersave(struct ath_hw *ah,
-					       int restore,
-					       int power_off)
+					       bool power_off)
 {
-	ath9k_hw_ops(ah)->config_pci_powersave(ah, restore, power_off);
+	ath9k_hw_ops(ah)->config_pci_powersave(ah, power_off);
 }
 
 static inline void ath9k_hw_rxena(struct ath_hw *ah)

drivers/net/wireless/ath/ath9k/hw.h

@@ -606,8 +606,7 @@ struct ath_hw_private_ops {
  */
 struct ath_hw_ops {
 	void (*config_pci_powersave)(struct ath_hw *ah,
-				     int restore,
-				     int power_off);
+				     bool power_off);
 	void (*rx_enable)(struct ath_hw *ah);
 	void (*set_desc_link)(void *ds, u32 link);
 	bool (*calibrate)(struct ath_hw *ah,

drivers/net/wireless/ath/ath9k/main.c

@@ -888,7 +888,7 @@ static void ath_radio_enable(struct ath_softc *sc, struct ieee80211_hw *hw)
 	spin_lock_bh(&sc->sc_pcu_lock);
 	atomic_set(&ah->intr_ref_cnt, -1);
 
-	ath9k_hw_configpcipowersave(ah, 0, 0);
+	ath9k_hw_configpcipowersave(ah, false);
 
 	if (!ah->curchan)
 		ah->curchan = ath9k_cmn_get_curchannel(sc->hw, ah);
@@ -969,7 +969,7 @@ void ath_radio_disable(struct ath_softc *sc, struct ieee80211_hw *hw)
 
 	ath9k_hw_phy_disable(ah);
 
-	ath9k_hw_configpcipowersave(ah, 1, 1);
+	ath9k_hw_configpcipowersave(ah, true);
 
 	spin_unlock_bh(&sc->sc_pcu_lock);
 	ath9k_ps_restore(sc);
@@ -1069,7 +1069,7 @@ static int ath9k_start(struct ieee80211_hw *hw)
 	init_channel = ath9k_cmn_get_curchannel(hw, ah);
 
 	/* Reset SERDES registers */
-	ath9k_hw_configpcipowersave(ah, 0, 0);
+	ath9k_hw_configpcipowersave(ah, false);
 
 	/*
 	 * The basic interface to setting the hardware in a good

drivers/net/wireless/ath/ath9k/pci.c

@@ -35,6 +35,7 @@ static DEFINE_PCI_DEVICE_TABLE(ath_pci_id_table) = {
 	{ 0 }
 };
 
+
 /* return bus cachesize in 4B word units */
 static void ath_pci_read_cachesize(struct ath_common *common, int *csz)
 {
@@ -137,7 +138,7 @@ static void ath_pci_aspm_init(struct ath_common *common)
 	if (aspm & (PCIE_LINK_STATE_L0S | PCIE_LINK_STATE_L1)) {
 		ah->aspm_enabled = true;
 		/* Initialize PCIe PM and SERDES registers. */
-		ath9k_hw_configpcipowersave(ah, 0, 0);
+		ath9k_hw_configpcipowersave(ah, false);
 	}
 }