Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (21 commits)
  ARM: OMAP4: MMC: increase delay for pbias
  arm: omap2plus: move NAND_BLOCK_SIZE out of boards
  omap4: hwmod: Enable the keypad
  omap3: Free Beagle rev gpios when they are read, so others can read them later
  arm: omap3: beagle: Ensure msecure is mux'd to be able to set the RTC
  omap: rx51: Don't power up speaker amplifier at bootup
  omap: rx51: Set regulator V28_A always on
  ARM: OMAP4: MMC: no regulator off during probe for eMMC
  arm: omap2plus: fix ads7846 pendown gpio request
  ARM: OMAP2: Add missing iounmap in omap4430_phy_init
  ARM: omap4: Pass core and wakeup mux tables to omap4_mux_init
  ARM: omap2+: mux: Allow board mux settings to be NULL
  OMAP4: fix return value of omap4_l3_init
  OMAP: iovmm: fix SW flags passed by user
  arch/arm/mach-omap1/dma.c: Invert calls to platform_device_put and platform_device_del
  OMAP2+: mux: fix compilation warnings
  OMAP: SRAM: Fix warning: format '%08lx' expects type 'long unsigned int'
  arm: omap3: cm-t3517: fix section mismatch warning
  OMAP2+: Fix 9 section mismatch(es) warnings from mach-omap2/built-in.o
  ARM: OMAP2: Add missing include of linux/gpio.h
  ...

arch/arm/mach-omap1/dma.c

@@ -284,14 +284,15 @@ static int __init omap1_system_dma_init(void)
 	dma_base = ioremap(res[0].start, resource_size(&res[0]));
 	if (!dma_base) {
 		pr_err("%s: Unable to ioremap\n", __func__);
-		return -ENODEV;
+		ret = -ENODEV;
+		goto exit_device_put;
 	}
 
 	ret = platform_device_add_resources(pdev, res, ARRAY_SIZE(res));
 	if (ret) {
 		dev_err(&pdev->dev, "%s: Unable to add resources for %s%d\n",
 			__func__, pdev->name, pdev->id);
-		goto exit_device_del;
+		goto exit_device_put;
 	}
 
 	p = kzalloc(sizeof(struct omap_system_dma_plat_info), GFP_KERNEL);
@@ -299,7 +300,7 @@ static int __init omap1_system_dma_init(void)
 		dev_err(&pdev->dev, "%s: Unable to allocate 'p' for %s\n",
 			__func__, pdev->name);
 		ret = -ENOMEM;
-		goto exit_device_put;
+		goto exit_device_del;
 	}
 
 	d = kzalloc(sizeof(struct omap_dma_dev_attr), GFP_KERNEL);
@@ -380,10 +381,10 @@ static int __init omap1_system_dma_init(void)
 	kfree(d);
 exit_release_p:
 	kfree(p);
-exit_device_put:
-	platform_device_put(pdev);
 exit_device_del:
 	platform_device_del(pdev);
+exit_device_put:
+	platform_device_put(pdev);
 
 	return ret;
 }

arch/arm/mach-omap2/board-2430sdp.c

@@ -26,13 +26,13 @@
 #include <linux/err.h>
 #include <linux/clk.h>
 #include <linux/io.h>
+#include <linux/gpio.h>
 
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <mach/gpio.h>
 #include <plat/board.h>
 #include <plat/common.h>
 #include <plat/gpmc.h>

arch/arm/mach-omap2/board-3430sdp.c

@@ -622,19 +622,19 @@ static struct omap_device_pad serial3_pads[] __initdata = {
 			 OMAP_MUX_MODE0),
 };
 
-static struct omap_board_data serial1_data = {
+static struct omap_board_data serial1_data __initdata = {
 	.id		= 0,
 	.pads		= serial1_pads,
 	.pads_cnt	= ARRAY_SIZE(serial1_pads),
 };
 
-static struct omap_board_data serial2_data = {
+static struct omap_board_data serial2_data __initdata = {
 	.id		= 1,
 	.pads		= serial2_pads,
 	.pads_cnt	= ARRAY_SIZE(serial2_pads),
 };
 
-static struct omap_board_data serial3_data = {
+static struct omap_board_data serial3_data __initdata = {
 	.id		= 2,
 	.pads		= serial3_pads,
 	.pads_cnt	= ARRAY_SIZE(serial3_pads),

arch/arm/mach-omap2/board-4430sdp.c

@@ -258,7 +258,7 @@ static struct gpio sdp4430_eth_gpios[] __initdata = {
 	{ ETH_KS8851_IRQ,	GPIOF_IN,		"eth_irq"	},
 };
 
-static int omap_ethernet_init(void)
+static int __init omap_ethernet_init(void)
 {
 	int status;
 
@@ -322,6 +322,7 @@ static struct omap2_hsmmc_info mmc[] = {
 		.gpio_wp	= -EINVAL,
 		.nonremovable   = true,
 		.ocr_mask	= MMC_VDD_29_30,
+		.no_off_init	= true,
 	},
 	{
 		.mmc		= 1,
@@ -681,19 +682,19 @@ static struct omap_device_pad serial4_pads[] __initdata = {
 			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
 };
 
-static struct omap_board_data serial2_data = {
+static struct omap_board_data serial2_data __initdata = {
 	.id		= 1,
 	.pads		= serial2_pads,
 	.pads_cnt	= ARRAY_SIZE(serial2_pads),
 };
 
-static struct omap_board_data serial3_data = {
+static struct omap_board_data serial3_data __initdata = {
 	.id		= 2,
 	.pads		= serial3_pads,
 	.pads_cnt	= ARRAY_SIZE(serial3_pads),
 };
 
-static struct omap_board_data serial4_data = {
+static struct omap_board_data serial4_data __initdata = {
 	.id		= 3,
 	.pads		= serial4_pads,
 	.pads_cnt	= ARRAY_SIZE(serial4_pads),
@@ -729,7 +730,7 @@ static void __init omap_4430sdp_init(void)
 
 	if (omap_rev() == OMAP4430_REV_ES1_0)
 		package = OMAP_PACKAGE_CBL;
-	omap4_mux_init(board_mux, package);
+	omap4_mux_init(board_mux, NULL, package);
 
 	omap_board_config = sdp4430_config;
 	omap_board_config_size = ARRAY_SIZE(sdp4430_config);

arch/arm/mach-omap2/board-apollon.c

@@ -27,13 +27,13 @@
 #include <linux/err.h>
 #include <linux/clk.h>
 #include <linux/smc91x.h>
+#include <linux/gpio.h>
 
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/flash.h>
 
-#include <mach/gpio.h>
 #include <plat/led.h>
 #include <plat/usb.h>
 #include <plat/board.h>

arch/arm/mach-omap2/board-cm-t35.c

@@ -63,8 +63,6 @@
 #define SB_T35_SMSC911X_CS	4
 #define SB_T35_SMSC911X_GPIO	65
 
-#define NAND_BLOCK_SIZE		SZ_128K
-
 #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
 #include <linux/smsc911x.h>
 #include <plat/gpmc-smsc911x.h>

arch/arm/mach-omap2/board-cm-t3517.c

@@ -48,6 +48,7 @@
 
 #include "mux.h"
 #include "control.h"
+#include "common-board-devices.h"
 
 #if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
 static struct gpio_led cm_t3517_leds[] = {
@@ -177,7 +178,7 @@ static struct usbhs_omap_board_data cm_t3517_ehci_pdata __initdata = {
 	.reset_gpio_port[2]  = -EINVAL,
 };
 
-static int cm_t3517_init_usbh(void)
+static int __init cm_t3517_init_usbh(void)
 {
 	int err;
 
@@ -203,8 +204,6 @@ static inline int cm_t3517_init_usbh(void)
 #endif
 
 #if defined(CONFIG_MTD_NAND_OMAP2) || defined(CONFIG_MTD_NAND_OMAP2_MODULE)
-#define NAND_BLOCK_SIZE		SZ_128K
-
 static struct mtd_partition cm_t3517_nand_partitions[] = {
 	{
 		.name           = "xloader",

arch/arm/mach-omap2/board-devkit8000.c

@@ -61,8 +61,6 @@
 #include "timer-gp.h"
 #include "common-board-devices.h"
 
-#define NAND_BLOCK_SIZE		SZ_128K
-
 #define OMAP_DM9000_GPIO_IRQ	25
 #define OMAP3_DEVKIT_TS_GPIO	27
 

arch/arm/mach-omap2/board-omap3beagle.c

@@ -54,8 +54,6 @@
 #include "pm.h"
 #include "common-board-devices.h"
 
-#define NAND_BLOCK_SIZE		SZ_128K
-
 /*
  * OMAP3 Beagle revision
  * Run time detection of Beagle revision is done by reading GPIO.
@@ -106,6 +104,9 @@ static void __init omap3_beagle_init_rev(void)
 	beagle_rev = gpio_get_value(171) | (gpio_get_value(172) << 1)
 			| (gpio_get_value(173) << 2);
 
+	gpio_free_array(omap3_beagle_rev_gpios,
+			ARRAY_SIZE(omap3_beagle_rev_gpios));
+
 	switch (beagle_rev) {
 	case 7:
 		printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n");
@@ -579,6 +580,9 @@ static void __init omap3_beagle_init(void)
 	omap_nand_flash_init(NAND_BUSWIDTH_16, omap3beagle_nand_partitions,
 			     ARRAY_SIZE(omap3beagle_nand_partitions));
 
+	/* Ensure msecure is mux'd to be able to set the RTC. */
+	omap_mux_init_signal("sys_drm_msecure", OMAP_PIN_OFF_OUTPUT_HIGH);
+
 	/* Ensure SDRC pins are mux'd for self-refresh */
 	omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
 	omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);

arch/arm/mach-omap2/board-omap3pandora.c

@@ -30,6 +30,7 @@
 #include <linux/leds.h>
 #include <linux/input.h>
 #include <linux/input/matrix_keypad.h>
+#include <linux/gpio.h>
 #include <linux/gpio_keys.h>
 #include <linux/mmc/host.h>
 #include <linux/mmc/card.h>
@@ -41,7 +42,6 @@
 
 #include <plat/board.h>
 #include <plat/common.h>
-#include <mach/gpio.h>
 #include <mach/hardware.h>
 #include <plat/mcspi.h>
 #include <plat/usb.h>
@@ -57,8 +57,6 @@
 #define PANDORA_WIFI_NRESET_GPIO	23
 #define OMAP3_PANDORA_TS_GPIO		94
 
-#define NAND_BLOCK_SIZE			SZ_128K
-
 static struct mtd_partition omap3pandora_nand_partitions[] = {
 	{
 		.name           = "xloader",

arch/arm/mach-omap2/board-omap3touchbook.c

@@ -56,8 +56,6 @@
 
 #include <asm/setup.h>
 
-#define NAND_BLOCK_SIZE		SZ_128K
-
 #define OMAP3_AC_GPIO		136
 #define OMAP3_TS_GPIO		162
 #define TB_BL_PWM_TIMER		9

arch/arm/mach-omap2/board-omap4panda.c

@@ -526,19 +526,19 @@ static struct omap_device_pad serial4_pads[] __initdata = {
 			 OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
 };
 
-static struct omap_board_data serial2_data = {
+static struct omap_board_data serial2_data __initdata = {
 	.id             = 1,
 	.pads           = serial2_pads,
 	.pads_cnt       = ARRAY_SIZE(serial2_pads),
 };
 
-static struct omap_board_data serial3_data = {
+static struct omap_board_data serial3_data __initdata = {
 	.id             = 2,
 	.pads           = serial3_pads,
 	.pads_cnt       = ARRAY_SIZE(serial3_pads),
 };
 
-static struct omap_board_data serial4_data = {
+static struct omap_board_data serial4_data __initdata = {
 	.id             = 3,
 	.pads           = serial4_pads,
 	.pads_cnt       = ARRAY_SIZE(serial4_pads),
@@ -687,7 +687,7 @@ static void __init omap4_panda_init(void)
 
 	if (omap_rev() == OMAP4430_REV_ES1_0)
 		package = OMAP_PACKAGE_CBL;
-	omap4_mux_init(board_mux, package);
+	omap4_mux_init(board_mux, NULL, package);
 
 	if (wl12xx_set_platform_data(&omap_panda_wlan_data))
 		pr_err("error setting wl12xx data\n");

arch/arm/mach-omap2/board-overo.c

@@ -24,6 +24,7 @@
 #include <linux/err.h>
 #include <linux/init.h>
 #include <linux/io.h>
+#include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/platform_device.h>
 #include <linux/i2c/twl.h>
@@ -45,7 +46,6 @@
 #include <plat/common.h>
 #include <video/omapdss.h>
 #include <video/omap-panel-generic-dpi.h>
-#include <mach/gpio.h>
 #include <plat/gpmc.h>
 #include <mach/hardware.h>
 #include <plat/nand.h>
@@ -65,8 +65,6 @@
 #define OVERO_GPIO_USBH_CPEN	168
 #define OVERO_GPIO_USBH_NRESET	183
 
-#define NAND_BLOCK_SIZE SZ_128K
-
 #define OVERO_SMSC911X_CS      5
 #define OVERO_SMSC911X_GPIO    176
 #define OVERO_SMSC911X2_CS     4

arch/arm/mach-omap2/board-rx51-peripherals.c

@@ -488,6 +488,7 @@ static struct regulator_init_data rx51_vmmc2 = {
 		.name			= "V28_A",
 		.min_uV			= 2800000,
 		.max_uV			= 3000000,
+		.always_on		= true, /* due VIO leak to AIC34 VDDs */
 		.apply_uV		= true,
 		.valid_modes_mask	= REGULATOR_MODE_NORMAL
 					| REGULATOR_MODE_STANDBY,
@@ -582,7 +583,7 @@ static int rx51_twlgpio_setup(struct device *dev, unsigned gpio, unsigned n)
 {
 	/* FIXME this gpio setup is just a placeholder for now */
 	gpio_request_one(gpio + 6, GPIOF_OUT_INIT_LOW, "backlight_pwm");
-	gpio_request_one(gpio + 7, GPIOF_OUT_INIT_HIGH, "speaker_en");
+	gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "speaker_en");
 
 	return 0;
 }

arch/arm/mach-omap2/board-zoom-display.c

@@ -26,7 +26,7 @@ static struct gpio zoom_lcd_gpios[] __initdata = {
 	{ LCD_PANEL_QVGA_GPIO,	GPIOF_OUT_INIT_HIGH, "lcd qvga"	 },
 };
 
-static void zoom_lcd_panel_init(void)
+static void __init zoom_lcd_panel_init(void)
 {
 	zoom_lcd_gpios[0].gpio = (omap_rev() > OMAP3430_REV_ES3_0) ?
 			LCD_PANEL_RESET_GPIO_PROD :

arch/arm/mach-omap2/common-board-devices.c

@@ -85,17 +85,17 @@ void __init omap_ads7846_init(int bus_num, int gpio_pendown, int gpio_debounce,
 	struct spi_board_info *spi_bi = &ads7846_spi_board_info;
 	int err;
 
-	err = gpio_request(gpio_pendown, "TS PenDown");
+	if (board_pdata && board_pdata->get_pendown_state) {
+		err = gpio_request_one(gpio_pendown, GPIOF_IN, "TSPenDown");
 		if (err) {
-		pr_err("Could not obtain gpio for TS PenDown: %d\n", err);
+			pr_err("Couldn't obtain gpio for TSPenDown: %d\n", err);
 			return;
 		}
-
-	gpio_direction_input(gpio_pendown);
 		gpio_export(gpio_pendown, 0);
 
 		if (gpio_debounce)
 			gpio_set_debounce(gpio_pendown, gpio_debounce);
+	}
 
 	ads7846_config.gpio_pendown = gpio_pendown;
 

arch/arm/mach-omap2/common-board-devices.h

 #ifndef __OMAP_COMMON_BOARD_DEVICES__
 #define __OMAP_COMMON_BOARD_DEVICES__
 
+#define NAND_BLOCK_SIZE	SZ_128K
+
 struct twl4030_platform_data;
 struct mtd_partition;
 

arch/arm/mach-omap2/devices.c

@@ -97,7 +97,7 @@ static int __init omap4_l3_init(void)
 
 	WARN(IS_ERR(od), "could not build omap_device for %s\n", oh_name);
 
-	return PTR_ERR(od);
+	return IS_ERR(od) ? PTR_ERR(od) : 0;
 }
 postcore_initcall(omap4_l3_init);
 

arch/arm/mach-omap2/hsmmc.c

@@ -145,6 +145,7 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot,
 				 int power_on, int vdd)
 {
 	u32 reg;
+	unsigned long timeout;
 
 	if (power_on) {
 		reg = omap4_ctrl_pad_readl(control_pbias_offset);
@@ -157,9 +158,15 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot,
 			OMAP4_MMC1_PWRDNZ_MASK |
 			OMAP4_USBC1_ICUSB_PWRDNZ_MASK);
 		omap4_ctrl_pad_writel(reg, control_pbias_offset);
-		/* 4 microsec delay for comparator to generate an error*/
-		udelay(4);
+
+		timeout = jiffies + msecs_to_jiffies(5);
+		do {
 			reg = omap4_ctrl_pad_readl(control_pbias_offset);
+			if (!(reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK))
+				break;
+			usleep_range(100, 200);
+		} while (!time_after(jiffies, timeout));
+
 		if (reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK) {
 			pr_err("Pbias Voltage is not same as LDO\n");
 			/* Caution : On VMODE_ERROR Power Down MMC IO */
@@ -331,6 +338,9 @@ static int __init omap_hsmmc_pdata_init(struct omap2_hsmmc_info *c,
 	if (c->no_off)
 		mmc->slots[0].no_off = 1;
 
+	if (c->no_off_init)
+		mmc->slots[0].no_regulator_off_init = c->no_off_init;
+
 	if (c->vcc_aux_disable_is_sleep)
 		mmc->slots[0].vcc_aux_disable_is_sleep = 1;
 

arch/arm/mach-omap2/hsmmc.h

@@ -18,6 +18,7 @@ struct omap2_hsmmc_info {
 	bool	nonremovable;	/* Nonremovable e.g. eMMC */
 	bool	power_saving;	/* Try to sleep or power off when possible */
 	bool	no_off;		/* power_saving and power is not to go off */
+	bool	no_off_init;	/* no power off when not in MMC sleep state */
 	bool	vcc_aux_disable_is_sleep; /* Regulator off remapped to sleep */
 	int	gpio_cd;	/* or -EINVAL */
 	int	gpio_wp;	/* or -EINVAL */

arch/arm/mach-omap2/mux.c

@@ -83,6 +83,9 @@ void omap_mux_write(struct omap_mux_partition *partition, u16 val,
 void omap_mux_write_array(struct omap_mux_partition *partition,
 				 struct omap_board_mux *board_mux)
 {
+	if (!board_mux)
+		return;
+
 	while (board_mux->reg_offset != OMAP_MUX_TERMINATOR) {
 		omap_mux_write(partition, board_mux->value,
 			       board_mux->reg_offset);
@@ -906,7 +909,7 @@ static struct omap_mux *omap_mux_get_by_gpio(
 u16 omap_mux_get_gpio(int gpio)
 {
 	struct omap_mux_partition *partition;
-	struct omap_mux *m;
+	struct omap_mux *m = NULL;
 
 	list_for_each_entry(partition, &mux_partitions, node) {
 		m = omap_mux_get_by_gpio(partition, gpio);

arch/arm/mach-omap2/mux.h

@@ -323,10 +323,12 @@ int omap3_mux_init(struct omap_board_mux *board_mux, int flags);
 
 /**
  * omap4_mux_init() - initialize mux system with board specific set
- * @board_mux:		Board specific mux table
+ * @board_subset:	Board specific mux table
+ * @board_wkup_subset:	Board specific mux table for wakeup instance
  * @flags:		OMAP package type used for the board
  */
-int omap4_mux_init(struct omap_board_mux *board_mux, int flags);
+int omap4_mux_init(struct omap_board_mux *board_subset,
+	struct omap_board_mux *board_wkup_subset, int flags);
 
 /**
  * omap_mux_init - private mux init function, do not call

arch/arm/mach-omap2/mux44xx.c

@@ -1309,7 +1309,8 @@ static struct omap_ball __initdata omap4_wkup_cbl_cbs_ball[] = {
 #define omap4_wkup_cbl_cbs_ball  NULL
 #endif
 
-int __init omap4_mux_init(struct omap_board_mux *board_subset, int flags)
+int __init omap4_mux_init(struct omap_board_mux *board_subset,
+	struct omap_board_mux *board_wkup_subset, int flags)
 {
 	struct omap_ball *package_balls_core;
 	struct omap_ball *package_balls_wkup = omap4_wkup_cbl_cbs_ball;
@@ -1347,7 +1348,7 @@ int __init omap4_mux_init(struct omap_board_mux *board_subset, int flags)
 			    OMAP_MUX_GPIO_IN_MODE3,
 			    OMAP4_CTRL_MODULE_PAD_WKUP_MUX_PBASE,
 			    OMAP4_CTRL_MODULE_PAD_WKUP_MUX_SIZE,
-			    omap4_wkup_muxmodes, NULL, board_subset,
+			    omap4_wkup_muxmodes, NULL, board_wkup_subset,
 			    package_balls_wkup);
 
 	return ret;

arch/arm/mach-omap2/omap_hwmod.c

@@ -1628,7 +1628,7 @@ int omap_hwmod_for_each(int (*fn)(struct omap_hwmod *oh, void *data),
 			void *data)
 {
 	struct omap_hwmod *temp_oh;
-	int ret;
+	int ret = 0;
 
 	if (!fn)
 		return -EINVAL;

arch/arm/mach-omap2/omap_hwmod_44xx_data.c

@@ -5109,7 +5109,7 @@ static __initdata struct omap_hwmod *omap44xx_hwmods[] = {
 	&omap44xx_iva_seq1_hwmod,
 
 	/* kbd class */
-/*	&omap44xx_kbd_hwmod, */
+	&omap44xx_kbd_hwmod,
 
 	/* mailbox class */
 	&omap44xx_mailbox_hwmod,

arch/arm/mach-omap2/omap_phy_internal.c

@@ -56,8 +56,10 @@ int omap4430_phy_init(struct device *dev)
 	/* Power down the phy */
 	__raw_writel(PHY_PD, ctrl_base + CONTROL_DEV_CONF);
 
-	if (!dev)
+	if (!dev) {
+		iounmap(ctrl_base);
 		return 0;
+	}
 
 	phyclk = clk_get(dev, "ocp2scp_usb_phy_ick");
 	if (IS_ERR(phyclk)) {

arch/arm/plat-omap/include/plat/flash.h

@@ -11,6 +11,7 @@
 
 #include <linux/mtd/map.h>
 
+struct platform_device;
 extern void omap1_set_vpp(struct platform_device *pdev, int enable);
 
 #endif

arch/arm/plat-omap/include/plat/iovmm.h

@@ -29,9 +29,6 @@ struct iovm_struct {
  * lower 16 bit is used for h/w and upper 16 bit is for s/w.
  */
 #define IOVMF_SW_SHIFT		16
-#define IOVMF_HW_SIZE		(1 << IOVMF_SW_SHIFT)
-#define IOVMF_HW_MASK		(IOVMF_HW_SIZE - 1)
-#define IOVMF_SW_MASK		(~IOVMF_HW_MASK)UL
 
 /*
  * iovma: h/w flags derived from cam and ram attribute

arch/arm/plat-omap/include/plat/mmc.h

@@ -101,6 +101,9 @@ struct omap_mmc_platform_data {
 		/* If using power_saving and the MMC power is not to go off */
 		unsigned no_off:1;
 
+		/* eMMC does not handle power off when not in sleep state */
+		unsigned no_regulator_off_init:1;
+
 		/* Regulator off remapped to sleep */
 		unsigned vcc_aux_disable_is_sleep:1;
 

arch/arm/plat-omap/iovmm.c

@@ -648,7 +648,6 @@ u32 iommu_vmap(struct iommu *obj, u32 da, const struct sg_table *sgt,
 			return PTR_ERR(va);
 	}
 
-	flags &= IOVMF_HW_MASK;
 	flags |= IOVMF_DISCONT;
 	flags |= IOVMF_MMIO;
 
@@ -706,7 +705,6 @@ u32 iommu_vmalloc(struct iommu *obj, u32 da, size_t bytes, u32 flags)
 	if (!va)
 		return -ENOMEM;
 
-	flags &= IOVMF_HW_MASK;
 	flags |= IOVMF_DISCONT;
 	flags |= IOVMF_ALLOC;
 
@@ -795,7 +793,6 @@ u32 iommu_kmap(struct iommu *obj, u32 da, u32 pa, size_t bytes,
 	if (!va)
 		return -ENOMEM;
 
-	flags &= IOVMF_HW_MASK;
 	flags |= IOVMF_LINEAR;
 	flags |= IOVMF_MMIO;
 
@@ -853,7 +850,6 @@ u32 iommu_kmalloc(struct iommu *obj, u32 da, size_t bytes, u32 flags)
 		return -ENOMEM;
 	pa = virt_to_phys(va);
 
-	flags &= IOVMF_HW_MASK;
 	flags |= IOVMF_LINEAR;
 	flags |= IOVMF_ALLOC;
 

arch/arm/plat-omap/sram.c

@@ -166,7 +166,7 @@ static void __init omap_detect_sram(void)
 		else if (cpu_is_omap1611())
 			omap_sram_size = SZ_256K;
 		else {
-			printk(KERN_ERR "Could not detect SRAM size\n");
+			pr_err("Could not detect SRAM size\n");
 			omap_sram_size = 0x4000;
 		}
 	}
@@ -221,8 +221,8 @@ static void __init omap_map_sram(void)
 	omap_sram_io_desc[0].length = ROUND_DOWN(omap_sram_size, PAGE_SIZE);
 	iotable_init(omap_sram_io_desc, ARRAY_SIZE(omap_sram_io_desc));
 
-	printk(KERN_INFO "SRAM: Mapped pa 0x%08lx to va 0x%08lx size: 0x%lx\n",
-	__pfn_to_phys(omap_sram_io_desc[0].pfn),
+	pr_info("SRAM: Mapped pa 0x%08llx to va 0x%08lx size: 0x%lx\n",
+		(long long) __pfn_to_phys(omap_sram_io_desc[0].pfn),
 		omap_sram_io_desc[0].virtual,
 		omap_sram_io_desc[0].length);
 
@@ -252,7 +252,7 @@ static void __init omap_map_sram(void)
 void *omap_sram_push_address(unsigned long size)
 {
 	if (size > (omap_sram_ceil - (omap_sram_base + SRAM_BOOTLOADER_SZ))) {
-		printk(KERN_ERR "Not enough space in SRAM\n");
+		pr_err("Not enough space in SRAM\n");
 		return NULL;
 	}
 

drivers/mmc/host/omap_hsmmc.c

@@ -435,6 +435,9 @@ static int omap_hsmmc_reg_get(struct omap_hsmmc_host *host)
 		reg = regulator_get(host->dev, "vmmc_aux");
 		host->vcc_aux = IS_ERR(reg) ? NULL : reg;
 
+		/* For eMMC do not power off when not in sleep state */
+		if (mmc_slot(host).no_regulator_off_init)
+			return 0;
 		/*
 		* UGLY HACK:  workaround regulator framework bugs.
 		* When the bootloader leaves a supply active, it's