Merge tag 'omap-for-v4.3/legacy-v2-signed' of...

Merge tag 'omap-for-v4.3/legacy-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup

Merge "drop few more legacy boards for v4.3" from Tony Lindgren:

Drop more omap3 legacy board-*.c files for v4.3. This time we're
dropping the board files for omap3logic and omap3pandora.

The reason for dropping these now rather than later is that now
we can simply revert the patches in case of unexpected issues as
we are not dropping any platform data at this point.

This leaves us with only the following board-*.c files:

BOARD                   REASON NEEDED
board-ldp.c             Still used in RMKs boot test system
board-rx51-*.c          Needs /proc/atags support for user space

Once we have the n900 legacy user space issues sorted out for
/proc/atags and system_rev, we can drop the remaining two
board-*.c files. And then one merge window after that we can
drop the legacy booting support assuming no unexpected issues
are found.

* tag 'omap-for-v4.3/legacy-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: Remove legacy booting support for Pandora
  ARM: OMAP2+: Remove legacy booting support for LogicPD Torpedo
Signed-off-by: Olof Johansson <olof@lixom.net>

arch/arm/mach-omap2/Kconfig

@@ -177,26 +177,6 @@ config MACH_OMAP_LDP
 	default y
 	select OMAP_PACKAGE_CBB
 
-config MACH_OMAP3530_LV_SOM
-	bool "OMAP3 Logic 3530 LV SOM board"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CBB
-	help
-	 Support for the LogicPD OMAP3530 SOM Development kit
-	 for full description please see the products webpage at
-	 http://www.logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap35x-development-kit
-
-config MACH_OMAP3_TORPEDO
-	bool "OMAP3 Logic 35x Torpedo board"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CBB
-	help
-	 Support for the LogicPD OMAP35x Torpedo Development kit
-	 for full description please see the products webpage at
-	 http://www.logicpd.com/products/development-kits/zoom-omap35x-torpedo-development-kit
-
 config MACH_OMAP3517EVM
 	bool "OMAP3517/ AM3517 EVM board"
 	depends on ARCH_OMAP3

arch/arm/mach-omap2/Makefile

@@ -243,9 +243,6 @@ obj-$(CONFIG_SOC_OMAP2420)		+= msdi.o
 # Specific board support
 obj-$(CONFIG_MACH_OMAP_GENERIC)		+= board-generic.o pdata-quirks.o
 obj-$(CONFIG_MACH_OMAP_LDP)		+= board-ldp.o
-obj-$(CONFIG_MACH_OMAP3530_LV_SOM)      += board-omap3logic.o
-obj-$(CONFIG_MACH_OMAP3_TORPEDO)        += board-omap3logic.o
-obj-$(CONFIG_MACH_OMAP3_PANDORA)	+= board-omap3pandora.o
 obj-$(CONFIG_MACH_NOKIA_N8X0)		+= board-n8x0.o
 obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51.o sdram-nokia.o
 obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51-peripherals.o

arch/arm/mach-omap2/board-omap3logic.c

-/*
- * linux/arch/arm/mach-omap2/board-omap3logic.c
- *
- * Copyright (C) 2010 Li-Pro.Net
- * Stephan Linz <linz@li-pro.net>
- *
- * Copyright (C) 2010-2012 Logic Product Development, Inc.
- * Peter Barada <peter.barada@logicpd.com>
- * Ashwin BIhari <ashwin.bihari@logicpd.com>
- *
- * Modified from Beagle, EVM, and RX51
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/gpio.h>
-
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-
-#include <linux/i2c/twl.h>
-#include <linux/mmc/host.h>
-#include <linux/usb/phy.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "mux.h"
-#include "hsmmc.h"
-#include "control.h"
-#include "common-board-devices.h"
-#include "gpmc.h"
-#include "gpmc-smsc911x.h"
-
-#define OMAP3LOGIC_SMSC911X_CS			1
-
-#define OMAP3530_LV_SOM_MMC_GPIO_CD		110
-#define OMAP3530_LV_SOM_MMC_GPIO_WP		126
-#define OMAP3530_LV_SOM_SMSC911X_GPIO_IRQ	152
-
-#define OMAP3_TORPEDO_MMC_GPIO_CD		127
-#define OMAP3_TORPEDO_SMSC911X_GPIO_IRQ		129
-
-static struct regulator_consumer_supply omap3logic_vmmc1_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data omap3logic_vmmc1 = {
-	.constraints = {
-		.name			= "VMMC1",
-		.min_uV			= 1850000,
-		.max_uV			= 3150000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies  = ARRAY_SIZE(omap3logic_vmmc1_supply),
-	.consumer_supplies      = omap3logic_vmmc1_supply,
-};
-
-static struct twl4030_gpio_platform_data omap3logic_gpio_data = {
-	.use_leds	= true,
-	.pullups	= BIT(1),
-	.pulldowns	= BIT(2)  | BIT(6)  | BIT(7)  | BIT(8)
-			| BIT(13) | BIT(15) | BIT(16) | BIT(17),
-};
-
-static struct twl4030_usb_data omap3logic_usb_data = {
-	.usb_mode	= T2_USB_MODE_ULPI,
-};
-
-
-static struct twl4030_platform_data omap3logic_twldata = {
-	/* platform_data for children goes here */
-	.gpio		= &omap3logic_gpio_data,
-	.vmmc1		= &omap3logic_vmmc1,
-	.usb		= &omap3logic_usb_data,
-};
-
-static int __init omap3logic_i2c_init(void)
-{
-	omap3_pmic_init("twl4030", &omap3logic_twldata);
-	return 0;
-}
-
-static struct omap2_hsmmc_info __initdata board_mmc_info[] = {
-	{
-		.name		= "external",
-		.mmc		= 1,
-		.caps		= MMC_CAP_4_BIT_DATA,
-		.gpio_cd	= -EINVAL,
-		.gpio_wp	= -EINVAL,
-	},
-	{}      /* Terminator */
-};
-
-static void __init board_mmc_init(void)
-{
-	if (machine_is_omap3530_lv_som()) {
-		/* OMAP3530 LV SOM board */
-		board_mmc_info[0].gpio_cd = OMAP3530_LV_SOM_MMC_GPIO_CD;
-		board_mmc_info[0].gpio_wp = OMAP3530_LV_SOM_MMC_GPIO_WP;
-		omap_mux_init_signal("gpio_110", OMAP_PIN_OUTPUT);
-		omap_mux_init_signal("gpio_126", OMAP_PIN_OUTPUT);
-	} else if (machine_is_omap3_torpedo()) {
-		/* OMAP3 Torpedo board */
-		board_mmc_info[0].gpio_cd = OMAP3_TORPEDO_MMC_GPIO_CD;
-		omap_mux_init_signal("gpio_127", OMAP_PIN_OUTPUT);
-	} else {
-		/* unsupported board */
-		printk(KERN_ERR "%s(): unknown machine type\n", __func__);
-		return;
-	}
-
-	omap_hsmmc_init(board_mmc_info);
-}
-
-static struct omap_smsc911x_platform_data __initdata board_smsc911x_data = {
-	.cs             = OMAP3LOGIC_SMSC911X_CS,
-	.gpio_irq       = -EINVAL,
-	.gpio_reset     = -EINVAL,
-};
-
-/* TODO/FIXME (comment by Peter Barada, LogicPD):
- * Fix the PBIAS voltage for Torpedo MMC1 pins that
- * are used for other needs (IRQs, etc).            */
-static void omap3torpedo_fix_pbias_voltage(void)
-{
-	u16 control_pbias_offset = OMAP343X_CONTROL_PBIAS_LITE;
-	u32 reg;
-
-	if (machine_is_omap3_torpedo())
-	{
-		/* Set the bias for the pin */
-		reg = omap_ctrl_readl(control_pbias_offset);
-
-		reg &= ~OMAP343X_PBIASLITEPWRDNZ1;
-		omap_ctrl_writel(reg, control_pbias_offset);
-
-		/* 100ms delay required for PBIAS configuration */
-		msleep(100);
-
-		reg |= OMAP343X_PBIASLITEVMODE1;
-		reg |= OMAP343X_PBIASLITEPWRDNZ1;
-		omap_ctrl_writel(reg | 0x300, control_pbias_offset);
-	}
-}
-
-static inline void __init board_smsc911x_init(void)
-{
-	if (machine_is_omap3530_lv_som()) {
-		/* OMAP3530 LV SOM board */
-		board_smsc911x_data.gpio_irq =
-					OMAP3530_LV_SOM_SMSC911X_GPIO_IRQ;
-		omap_mux_init_signal("gpio_152", OMAP_PIN_INPUT);
-	} else if (machine_is_omap3_torpedo()) {
-		/* OMAP3 Torpedo board */
-		board_smsc911x_data.gpio_irq = OMAP3_TORPEDO_SMSC911X_GPIO_IRQ;
-		omap_mux_init_signal("gpio_129", OMAP_PIN_INPUT);
-	} else {
-		/* unsupported board */
-		printk(KERN_ERR "%s(): unknown machine type\n", __func__);
-		return;
-	}
-
-	gpmc_smsc911x_init(&board_smsc911x_data);
-}
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
-	/* mUSB */
-	OMAP3_MUX(HSUSB0_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_STP, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(HSUSB0_DIR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_NXT, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static struct regulator_consumer_supply dummy_supplies[] = {
-	REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
-	REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-static void __init omap3logic_init(void)
-{
-	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
-	omap3torpedo_fix_pbias_voltage();
-	omap3logic_i2c_init();
-	omap_serial_init();
-	omap_sdrc_init(NULL, NULL);
-	board_mmc_init();
-	board_smsc911x_init();
-
-	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
-	usb_musb_init(NULL);
-
-	/* Ensure SDRC pins are mux'd for self-refresh */
-	omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
-	omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
-}
-
-MACHINE_START(OMAP3_TORPEDO, "Logic OMAP3 Torpedo board")
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap3_map_io,
-	.init_early	= omap35xx_init_early,
-	.init_irq	= omap3_init_irq,
-	.init_machine	= omap3logic_init,
-	.init_late	= omap35xx_init_late,
-	.init_time	= omap3_sync32k_timer_init,
-	.restart	= omap3xxx_restart,
-MACHINE_END
-
-MACHINE_START(OMAP3530_LV_SOM, "OMAP Logic 3530 LV SOM board")
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap3_map_io,
-	.init_early	= omap35xx_init_early,
-	.init_irq	= omap3_init_irq,
-	.init_machine	= omap3logic_init,
-	.init_late	= omap35xx_init_late,
-	.init_time	= omap3_sync32k_timer_init,
-	.restart	= omap3xxx_restart,
-MACHINE_END