[PATCH] sky2: yukon-ec-u chipset initialization

Add more complete setup code for Yukon EC_U chipset.
Based on matching code in 8.31 code in SysKonnect vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>

drivers/net/sky2.c

@@ -232,7 +232,17 @@ static int sky2_set_power_state(struct sky2_hw *hw, pci_power_t state)
 			if (hw->ports > 1)
 				reg1 |= PCI_Y2_PHY2_COMA;
 		}
+
+		if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
+			pci_write_config_dword(hw->pdev, PCI_DEV_REG3, 0);
+			pci_read_config_dword(hw->pdev, PCI_DEV_REG4, &reg1);
+			reg1 &= P_ASPM_CONTROL_MSK;
+			pci_write_config_dword(hw->pdev, PCI_DEV_REG4, reg1);
+			pci_write_config_dword(hw->pdev, PCI_DEV_REG5, 0);
+		}
+
 		pci_write_config_dword(hw->pdev, PCI_DEV_REG1, reg1);
+
 		break;
 
 	case PCI_D3hot:
@@ -463,6 +473,20 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port)
 		ledover |= PHY_M_LED_MO_RX(MO_LED_OFF);
 	}
 
+	if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev >= 2) {
+		/* apply fixes in PHY AFE */
+		gm_phy_write(hw, port, 22, 255);
+		/* increase differential signal amplitude in 10BASE-T */
+		gm_phy_write(hw, port, 24, 0xaa99);
+		gm_phy_write(hw, port, 23, 0x2011);
+
+		/* fix for IEEE A/B Symmetry failure in 1000BASE-T */
+		gm_phy_write(hw, port, 24, 0xa204);
+		gm_phy_write(hw, port, 23, 0x2002);
+
+		/* set page register to 0 */
+		gm_phy_write(hw, port, 22, 0);
+	} else {
 		gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
 
 		if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) {
@@ -473,6 +497,7 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port)
 		if (ledover)
 			gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
 
+	}
 	/* Enable phy interrupt on auto-negotiation complete (or link up) */
 	if (sky2->autoneg == AUTONEG_ENABLE)
 		gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_COMPL);
@@ -953,6 +978,12 @@ static int sky2_rx_start(struct sky2_port *sky2)
 
 	sky2->rx_put = sky2->rx_next = 0;
 	sky2_qset(hw, rxq);
+
+	if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev >= 2) {
+		/* MAC Rx RAM Read is controlled by hardware */
+		sky2_write32(hw, Q_ADDR(rxq, Q_F), F_M_RX_RAM_DIS);
+	}
+
 	sky2_prefetch_init(hw, rxq, sky2->rx_le_map, RX_LE_SIZE - 1);
 
 	rx_set_checksum(sky2);
@@ -1035,9 +1066,10 @@ static int sky2_up(struct net_device *dev)
 		    RB_RST_SET);
 
 	sky2_qset(hw, txqaddr[port]);
-	if (hw->chip_id == CHIP_ID_YUKON_EC_U)
-		sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), 0x1a0);
 
+	/* Set almost empty threshold */
+	if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev == 1)
+		sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), 0x1a0);
 
 	sky2_prefetch_init(hw, txqaddr[port], sky2->tx_le_map,
 			   TX_RING_SIZE - 1);

drivers/net/sky2.h

@@ -5,14 +5,22 @@
 #define _SKY2_H
 
 /* PCI config registers */
-#define PCI_DEV_REG1	0x40
-#define PCI_DEV_REG2	0x44
-#define PCI_DEV_STATUS  0x7c
-#define PCI_OS_PCI_X    (1<<26)
+enum {
+	PCI_DEV_REG1	= 0x40,
+	PCI_DEV_REG2	= 0x44,
+	PCI_DEV_STATUS  = 0x7c,
+	PCI_DEV_REG3	= 0x80,
+	PCI_DEV_REG4	= 0x84,
+	PCI_DEV_REG5    = 0x88,
+};
 
-#define PEX_LNK_STAT	0xf2
-#define PEX_UNC_ERR_STAT 0x104
-#define PEX_DEV_CTRL	0xe8
+enum {
+	PEX_DEV_CAP	= 0xe4,
+	PEX_DEV_CTRL	= 0xe8,
+	PEX_DEV_STA	= 0xea,
+	PEX_LNK_STAT	= 0xf2,
+	PEX_UNC_ERR_STAT= 0x104,
+};
 
 /* Yukon-2 */
 enum pci_dev_reg_1 {
@@ -37,6 +45,25 @@ enum pci_dev_reg_2 {
 	PCI_USEDATA64	= 1<<0,		/* Use 64Bit Data bus ext */
 };
 
+/*	PCI_OUR_REG_4		32 bit	Our Register 4 (Yukon-ECU only) */
+enum pci_dev_reg_4 {
+					/* (Link Training & Status State Machine) */
+	P_TIMER_VALUE_MSK	= 0xffL<<16,	/* Bit 23..16:	Timer Value Mask */
+					/* (Active State Power Management) */
+	P_FORCE_ASPM_REQUEST	= 1<<15, /* Force ASPM Request (A1 only) */
+	P_ASPM_GPHY_LINK_DOWN	= 1<<14, /* GPHY Link Down (A1 only) */
+	P_ASPM_INT_FIFO_EMPTY	= 1<<13, /* Internal FIFO Empty (A1 only) */
+	P_ASPM_CLKRUN_REQUEST	= 1<<12, /* CLKRUN Request (A1 only) */
+
+	P_ASPM_FORCE_CLKREQ_ENA	= 1<<4,	/* Force CLKREQ Enable (A1b only) */
+	P_ASPM_CLKREQ_PAD_CTL	= 1<<3,	/* CLKREQ PAD Control (A1 only) */
+	P_ASPM_A1_MODE_SELECT	= 1<<2,	/* A1 Mode Select (A1 only) */
+	P_CLK_GATE_PEX_UNIT_ENA	= 1<<1,	/* Enable Gate PEX Unit Clock */
+	P_CLK_GATE_ROOT_COR_ENA	= 1<<0,	/* Enable Gate Root Core Clock */
+	P_ASPM_CONTROL_MSK	= P_FORCE_ASPM_REQUEST | P_ASPM_GPHY_LINK_DOWN
+				  | P_ASPM_CLKRUN_REQUEST | P_ASPM_INT_FIFO_EMPTY,
+};
+
 
 #define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \
 			       PCI_STATUS_SIG_SYSTEM_ERROR | \
@@ -507,6 +534,16 @@ enum {
 };
 #define Q_ADDR(reg, offs) (B8_Q_REGS + (reg) + (offs))
 
+/*	Q_F				32 bit	Flag Register */
+enum {
+	F_ALM_FULL	= 1<<27, /* Rx FIFO: almost full */
+	F_EMPTY		= 1<<27, /* Tx FIFO: empty flag */
+	F_FIFO_EOF	= 1<<26, /* Tag (EOF Flag) bit in FIFO */
+	F_WM_REACHED	= 1<<25, /* Watermark reached */
+	F_M_RX_RAM_DIS	= 1<<24, /* MAC Rx RAM Read Port disable */
+	F_FIFO_LEVEL	= 0x1fL<<16, /* Bit 23..16:	# of Qwords in FIFO */
+	F_WATER_MARK	= 0x0007ffL, /* Bit 10.. 0:	Watermark */
+};
 
 /* Queue Prefetch Unit Offsets, use Y2_QADDR() to address (Yukon-2 only)*/
 enum {
@@ -913,6 +950,8 @@ enum {
 	PHY_MARV_ID1_B2	= 0x0C25, /* Yukon-Plus (PHY 88E1011) */
 	PHY_MARV_ID1_C2	= 0x0CC2, /* Yukon-EC	(PHY 88E1111) */
 	PHY_MARV_ID1_Y2	= 0x0C91, /* Yukon-2	(PHY 88E1112) */
+	PHY_MARV_ID1_FE = 0x0C83, /* Yukon-FE   (PHY 88E3082 Rev.A1) */
+	PHY_MARV_ID1_ECU= 0x0CB0, /* Yukon-ECU  (PHY 88E1149 Rev.B2?) */
 };
 
 /* Advertisement register bits */