igb: New PHY_ID for i354 device

This patch changes PHY_ID for i354 device, now using M88E1543
instead of M88E1545.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

drivers/net/ethernet/intel/igb/e1000_82575.c

@@ -176,7 +176,7 @@ static s32 igb_init_phy_params_82575(struct e1000_hw *hw)
 
 	/* Verify phy id and set remaining function pointers */
 	switch (phy->id) {
-	case M88E1545_E_PHY_ID:
+	case M88E1543_E_PHY_ID:
 	case I347AT4_E_PHY_ID:
 	case M88E1112_E_PHY_ID:
 	case M88E1111_I_PHY_ID:
@@ -1448,7 +1448,7 @@ static s32 igb_setup_copper_link_82575(struct e1000_hw *hw)
 		switch (hw->phy.id) {
 		case I347AT4_E_PHY_ID:
 		case M88E1112_E_PHY_ID:
-		case M88E1545_E_PHY_ID:
+		case M88E1543_E_PHY_ID:
 		case I210_I_PHY_ID:
 			ret_val = igb_copper_link_setup_m88_gen2(hw);
 			break;
@@ -2477,28 +2477,28 @@ s32 igb_set_eee_i354(struct e1000_hw *hw)
 	u16 phy_data;
 
 	if ((hw->phy.media_type != e1000_media_type_copper) ||
-	    (phy->id != M88E1545_E_PHY_ID))
+	    (phy->id != M88E1543_E_PHY_ID))
 		goto out;
 
 	if (!hw->dev_spec._82575.eee_disable) {
 		/* Switch to PHY page 18. */
-		ret_val = phy->ops.write_reg(hw, E1000_M88E1545_PAGE_ADDR, 18);
+		ret_val = phy->ops.write_reg(hw, E1000_M88E1543_PAGE_ADDR, 18);
 		if (ret_val)
 			goto out;
 
-		ret_val = phy->ops.read_reg(hw, E1000_M88E1545_EEE_CTRL_1,
+		ret_val = phy->ops.read_reg(hw, E1000_M88E1543_EEE_CTRL_1,
 					    &phy_data);
 		if (ret_val)
 			goto out;
 
-		phy_data |= E1000_M88E1545_EEE_CTRL_1_MS;
-		ret_val = phy->ops.write_reg(hw, E1000_M88E1545_EEE_CTRL_1,
+		phy_data |= E1000_M88E1543_EEE_CTRL_1_MS;
+		ret_val = phy->ops.write_reg(hw, E1000_M88E1543_EEE_CTRL_1,
 					     phy_data);
 		if (ret_val)
 			goto out;
 
 		/* Return the PHY to page 0. */
-		ret_val = phy->ops.write_reg(hw, E1000_M88E1545_PAGE_ADDR, 0);
+		ret_val = phy->ops.write_reg(hw, E1000_M88E1543_PAGE_ADDR, 0);
 		if (ret_val)
 			goto out;
 
@@ -2549,7 +2549,7 @@ s32 igb_get_eee_status_i354(struct e1000_hw *hw, bool *status)
 
 	/* Check if EEE is supported on this device. */
 	if ((hw->phy.media_type != e1000_media_type_copper) ||
-	    (phy->id != M88E1545_E_PHY_ID))
+	    (phy->id != M88E1543_E_PHY_ID))
 		goto out;
 
 	ret_val = igb_read_xmdio_reg(hw, E1000_PCS_STATUS_ADDR_I354,

drivers/net/ethernet/intel/igb/e1000_defines.h

@@ -787,7 +787,7 @@
 #define I350_I_PHY_ID        0x015403B0
 #define M88_VENDOR           0x0141
 #define I210_I_PHY_ID        0x01410C00
-#define M88E1545_E_PHY_ID    0x01410EA0
+#define M88E1543_E_PHY_ID    0x01410EA0
 
 /* M88E1000 Specific Registers */
 #define M88E1000_PHY_SPEC_CTRL     0x10  /* PHY Specific Control Register */
@@ -909,9 +909,9 @@
 #define E1000_EEE_LP_ADV_DEV_I210    7           /* EEE LP Adv Device */
 #define E1000_EEE_LP_ADV_ADDR_I210   61          /* EEE LP Adv Register */
 #define E1000_MMDAC_FUNC_DATA        0x4000      /* Data, no post increment */
-#define E1000_M88E1545_PAGE_ADDR	0x16       /* Page Offset Register */
-#define E1000_M88E1545_EEE_CTRL_1	0x0
-#define E1000_M88E1545_EEE_CTRL_1_MS	0x0001     /* EEE Master/Slave */
+#define E1000_M88E1543_PAGE_ADDR	0x16       /* Page Offset Register */
+#define E1000_M88E1543_EEE_CTRL_1	0x0
+#define E1000_M88E1543_EEE_CTRL_1_MS	0x0001     /* EEE Master/Slave */
 #define E1000_EEE_ADV_DEV_I354		7
 #define E1000_EEE_ADV_ADDR_I354		60
 #define E1000_EEE_ADV_100_SUPPORTED	(1 << 1)   /* 100BaseTx EEE Supported */

drivers/net/ethernet/intel/igb/e1000_phy.c

@@ -1806,7 +1806,7 @@ s32 igb_get_cable_length_m88_gen2(struct e1000_hw *hw)
 		phy->max_cable_length = phy_data / (is_cm ? 100 : 1);
 		phy->cable_length = phy_data / (is_cm ? 100 : 1);
 		break;
-	case M88E1545_E_PHY_ID:
+	case M88E1543_E_PHY_ID:
 	case I347AT4_E_PHY_ID:
 		/* Remember the original page select and set it to 7 */
 		ret_val = phy->ops.read_reg(hw, I347AT4_PAGE_SELECT,