Commit 9af197a8 authored by Florian Fainelli's avatar Florian Fainelli Committed by David S. Miller

net: dsa: bcm_sf2: implement GPHY power down

Implement the power on/off recommended procedure for the Single GPHY we
have on our Starfighter 2 switch. In order to make sure we get proper
LED link/activity signaling during suspend, switch the link indication
from the Switch/MAC to the PHY.

Finally, since the GPHY needs to be reset to be put in low power mode,
we will loose any context applied to it: workarounds, EEE etc.. so we
need to call phy_init_hw() to get our fixups re-applied successfully.
Signed-off-by: default avatarFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent b083668c
......@@ -238,17 +238,28 @@ static void bcm_sf2_gphy_enable_set(struct dsa_switch *ds, bool enable)
struct bcm_sf2_priv *priv = ds_to_priv(ds);
u32 reg;
if (!enable)
return;
reg = reg_readl(priv, REG_SPHY_CNTRL);
if (enable) {
reg |= PHY_RESET;
reg &= ~(EXT_PWR_DOWN | IDDQ_BIAS);
reg &= ~(EXT_PWR_DOWN | IDDQ_BIAS | CK25_DIS);
reg_writel(priv, reg, REG_SPHY_CNTRL);
udelay(21);
reg = reg_readl(priv, REG_SPHY_CNTRL);
reg &= ~PHY_RESET;
} else {
reg |= EXT_PWR_DOWN | IDDQ_BIAS | PHY_RESET;
reg_writel(priv, reg, REG_SPHY_CNTRL);
mdelay(1);
reg |= CK25_DIS;
}
reg_writel(priv, reg, REG_SPHY_CNTRL);
/* Use PHY-driven LED signaling */
if (!enable) {
reg = reg_readl(priv, REG_LED_CNTRL(0));
reg |= SPDLNK_SRC_SEL;
reg_writel(priv, reg, REG_LED_CNTRL(0));
}
}
static int bcm_sf2_port_setup(struct dsa_switch *ds, int port,
......@@ -266,6 +277,24 @@ static int bcm_sf2_port_setup(struct dsa_switch *ds, int port,
/* Clear the Rx and Tx disable bits and set to no spanning tree */
core_writel(priv, 0, CORE_G_PCTL_PORT(port));
/* Re-enable the GPHY and re-apply workarounds */
if (port == 0 && priv->hw_params.num_gphy == 1) {
bcm_sf2_gphy_enable_set(ds, true);
if (phy) {
/* if phy_stop() has been called before, phy
* will be in halted state, and phy_start()
* will call resume.
*
* the resume path does not configure back
* autoneg settings, and since we hard reset
* the phy manually here, we need to reset the
* state machine also.
*/
phy->state = PHY_READY;
phy_init_hw(phy);
}
}
/* Enable port 7 interrupts to get notified */
if (port == 7)
intrl2_1_mask_clear(priv, P_IRQ_MASK(P7_IRQ_OFF));
......@@ -299,6 +328,9 @@ static void bcm_sf2_port_disable(struct dsa_switch *ds, int port,
intrl2_1_writel(priv, P_IRQ_MASK(P7_IRQ_OFF), INTRL2_CPU_CLEAR);
}
if (port == 0 && priv->hw_params.num_gphy == 1)
bcm_sf2_gphy_enable_set(ds, false);
if (dsa_is_cpu_port(ds, port))
off = CORE_IMP_CTL;
else
......
......@@ -61,6 +61,10 @@
#define LPI_COUNT_SHIFT 9
#define LPI_COUNT_MASK 0x3F
#define REG_LED_CNTRL_BASE 0x90
#define REG_LED_CNTRL(x) (REG_LED_CNTRL_BASE + (x) * 4)
#define SPDLNK_SRC_SEL (1 << 24)
/* Register set relative to 'INTRL2_0' and 'INTRL2_1' */
#define INTRL2_CPU_STATUS 0x00
#define INTRL2_CPU_SET 0x04
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment