Commit 9e5f1b27 authored by Anssi Hannula's avatar Anssi Hannula Committed by Marc Kleine-Budde

can: xilinx_can: add support for Xilinx CAN FD core

Add support for Xilinx CAN FD core.

The major difference from the previously supported cores is that there
are TX mailboxes instead of a TX FIFO and the RX FIFO access method is
different.

We only transmit one frame at a time to prevent the HW from reordering
frames (it uses CAN ID priority order).

Support for CAN FD protocol is not added yet.

v2: Removed unnecessary "rx-mode" DT property and wrapped some long
    lines.
Signed-off-by: default avatarAnssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: default avatarMarc Kleine-Budde <mkl@pengutronix.de>
parent 1598efe5
......@@ -2,7 +2,7 @@
*
* Copyright (C) 2012 - 2014 Xilinx, Inc.
* Copyright (C) 2009 PetaLogix. All rights reserved.
* Copyright (C) 2017 Sandvik Mining and Construction Oy
* Copyright (C) 2017 - 2018 Sandvik Mining and Construction Oy
*
* Description:
* This driver is developed for Axi CAN IP and for Zynq CANPS Controller.
......@@ -51,8 +51,18 @@ enum xcan_reg {
XCAN_ISR_OFFSET = 0x1C, /* Interrupt status */
XCAN_IER_OFFSET = 0x20, /* Interrupt enable */
XCAN_ICR_OFFSET = 0x24, /* Interrupt clear */
/* not on CAN FD cores */
XCAN_TXFIFO_OFFSET = 0x30, /* TX FIFO base */
XCAN_RXFIFO_OFFSET = 0x50, /* RX FIFO base */
XCAN_AFR_OFFSET = 0x60, /* Acceptance Filter */
/* only on CAN FD cores */
XCAN_TRR_OFFSET = 0x0090, /* TX Buffer Ready Request */
XCAN_AFR_EXT_OFFSET = 0x00E0, /* Acceptance Filter */
XCAN_FSR_OFFSET = 0x00E8, /* RX FIFO Status */
XCAN_TXMSG_BASE_OFFSET = 0x0100, /* TX Message Space */
XCAN_RXMSG_BASE_OFFSET = 0x1100, /* RX Message Space */
};
#define XCAN_FRAME_ID_OFFSET(frame_base) ((frame_base) + 0x00)
......@@ -60,6 +70,15 @@ enum xcan_reg {
#define XCAN_FRAME_DW1_OFFSET(frame_base) ((frame_base) + 0x08)
#define XCAN_FRAME_DW2_OFFSET(frame_base) ((frame_base) + 0x0C)
#define XCAN_CANFD_FRAME_SIZE 0x48
#define XCAN_TXMSG_FRAME_OFFSET(n) (XCAN_TXMSG_BASE_OFFSET + \
XCAN_CANFD_FRAME_SIZE * (n))
#define XCAN_RXMSG_FRAME_OFFSET(n) (XCAN_RXMSG_BASE_OFFSET + \
XCAN_CANFD_FRAME_SIZE * (n))
/* the single TX mailbox used by this driver on CAN FD HW */
#define XCAN_TX_MAILBOX_IDX 0
/* CAN register bit masks - XCAN_<REG>_<BIT>_MASK */
#define XCAN_SRR_CEN_MASK 0x00000002 /* CAN enable */
#define XCAN_SRR_RESET_MASK 0x00000001 /* Soft Reset the CAN core */
......@@ -69,6 +88,9 @@ enum xcan_reg {
#define XCAN_BTR_SJW_MASK 0x00000180 /* Synchronous jump width */
#define XCAN_BTR_TS2_MASK 0x00000070 /* Time segment 2 */
#define XCAN_BTR_TS1_MASK 0x0000000F /* Time segment 1 */
#define XCAN_BTR_SJW_MASK_CANFD 0x000F0000 /* Synchronous jump width */
#define XCAN_BTR_TS2_MASK_CANFD 0x00000F00 /* Time segment 2 */
#define XCAN_BTR_TS1_MASK_CANFD 0x0000003F /* Time segment 1 */
#define XCAN_ECR_REC_MASK 0x0000FF00 /* Receive error counter */
#define XCAN_ECR_TEC_MASK 0x000000FF /* Transmit error counter */
#define XCAN_ESR_ACKER_MASK 0x00000010 /* ACK error */
......@@ -82,6 +104,7 @@ enum xcan_reg {
#define XCAN_SR_NORMAL_MASK 0x00000008 /* Normal mode */
#define XCAN_SR_LBACK_MASK 0x00000002 /* Loop back mode */
#define XCAN_SR_CONFIG_MASK 0x00000001 /* Configuration mode */
#define XCAN_IXR_RXMNF_MASK 0x00020000 /* RX match not finished */
#define XCAN_IXR_TXFEMP_MASK 0x00004000 /* TX FIFO Empty */
#define XCAN_IXR_WKUP_MASK 0x00000800 /* Wake up interrupt */
#define XCAN_IXR_SLP_MASK 0x00000400 /* Sleep interrupt */
......@@ -99,10 +122,15 @@ enum xcan_reg {
#define XCAN_IDR_ID2_MASK 0x0007FFFE /* Extended message ident */
#define XCAN_IDR_RTR_MASK 0x00000001 /* Remote TX request */
#define XCAN_DLCR_DLC_MASK 0xF0000000 /* Data length code */
#define XCAN_FSR_FL_MASK 0x00003F00 /* RX Fill Level */
#define XCAN_FSR_IRI_MASK 0x00000080 /* RX Increment Read Index */
#define XCAN_FSR_RI_MASK 0x0000001F /* RX Read Index */
/* CAN register bit shift - XCAN_<REG>_<BIT>_SHIFT */
#define XCAN_BTR_SJW_SHIFT 7 /* Synchronous jump width */
#define XCAN_BTR_TS2_SHIFT 4 /* Time segment 2 */
#define XCAN_BTR_SJW_SHIFT_CANFD 16 /* Synchronous jump width */
#define XCAN_BTR_TS2_SHIFT_CANFD 8 /* Time segment 2 */
#define XCAN_IDR_ID1_SHIFT 21 /* Standard Messg Identifier */
#define XCAN_IDR_ID2_SHIFT 1 /* Extended Message Identifier */
#define XCAN_DLCR_DLC_SHIFT 28 /* Data length code */
......@@ -114,11 +142,23 @@ enum xcan_reg {
/* TX-FIFO-empty interrupt available */
#define XCAN_FLAG_TXFEMP 0x0001
/* RX Match Not Finished interrupt available */
#define XCAN_FLAG_RXMNF 0x0002
/* Extended acceptance filters with control at 0xE0 */
#define XCAN_FLAG_EXT_FILTERS 0x0004
/* TX mailboxes instead of TX FIFO */
#define XCAN_FLAG_TX_MAILBOXES 0x0008
/* RX FIFO with each buffer in separate registers at 0x1100
* instead of the regular FIFO at 0x50
*/
#define XCAN_FLAG_RX_FIFO_MULTI 0x0010
struct xcan_devtype_data {
unsigned int flags;
const struct can_bittiming_const *bittiming_const;
const char *bus_clk_name;
unsigned int btr_ts2_shift;
unsigned int btr_sjw_shift;
};
/**
......@@ -169,6 +209,18 @@ static const struct can_bittiming_const xcan_bittiming_const = {
.brp_inc = 1,
};
static const struct can_bittiming_const xcan_bittiming_const_canfd = {
.name = DRIVER_NAME,
.tseg1_min = 1,
.tseg1_max = 64,
.tseg2_min = 1,
.tseg2_max = 16,
.sjw_max = 16,
.brp_min = 1,
.brp_max = 256,
.brp_inc = 1,
};
/**
* xcan_write_reg_le - Write a value to the device register little endian
* @priv: Driver private data structure
......@@ -223,6 +275,23 @@ static u32 xcan_read_reg_be(const struct xcan_priv *priv, enum xcan_reg reg)
return ioread32be(priv->reg_base + reg);
}
/**
* xcan_rx_int_mask - Get the mask for the receive interrupt
* @priv: Driver private data structure
*
* Return: The receive interrupt mask used by the driver on this HW
*/
static u32 xcan_rx_int_mask(const struct xcan_priv *priv)
{
/* RXNEMP is better suited for our use case as it cannot be cleared
* while the FIFO is non-empty, but CAN FD HW does not have it
*/
if (priv->devtype.flags & XCAN_FLAG_RX_FIFO_MULTI)
return XCAN_IXR_RXOK_MASK;
else
return XCAN_IXR_RXNEMP_MASK;
}
/**
* set_reset_mode - Resets the CAN device mode
* @ndev: Pointer to net_device structure
......@@ -287,10 +356,10 @@ static int xcan_set_bittiming(struct net_device *ndev)
btr1 = (bt->prop_seg + bt->phase_seg1 - 1);
/* Setting Time Segment 2 in BTR Register */
btr1 |= (bt->phase_seg2 - 1) << XCAN_BTR_TS2_SHIFT;
btr1 |= (bt->phase_seg2 - 1) << priv->devtype.btr_ts2_shift;
/* Setting Synchronous jump width in BTR Register */
btr1 |= (bt->sjw - 1) << XCAN_BTR_SJW_SHIFT;
btr1 |= (bt->sjw - 1) << priv->devtype.btr_sjw_shift;
priv->write_reg(priv, XCAN_BRPR_OFFSET, btr0);
priv->write_reg(priv, XCAN_BTR_OFFSET, btr1);
......@@ -318,6 +387,7 @@ static int xcan_chip_start(struct net_device *ndev)
u32 reg_msr, reg_sr_mask;
int err;
unsigned long timeout;
u32 ier;
/* Check if it is in reset mode */
err = set_reset_mode(ndev);
......@@ -329,11 +399,15 @@ static int xcan_chip_start(struct net_device *ndev)
return err;
/* Enable interrupts */
priv->write_reg(priv, XCAN_IER_OFFSET,
XCAN_IXR_TXOK_MASK | XCAN_IXR_BSOFF_MASK |
ier = XCAN_IXR_TXOK_MASK | XCAN_IXR_BSOFF_MASK |
XCAN_IXR_WKUP_MASK | XCAN_IXR_SLP_MASK |
XCAN_IXR_RXNEMP_MASK | XCAN_IXR_ERROR_MASK |
XCAN_IXR_RXOFLW_MASK | XCAN_IXR_ARBLST_MASK);
XCAN_IXR_ERROR_MASK | XCAN_IXR_RXOFLW_MASK |
XCAN_IXR_ARBLST_MASK | xcan_rx_int_mask(priv);
if (priv->devtype.flags & XCAN_FLAG_RXMNF)
ier |= XCAN_IXR_RXMNF_MASK;
priv->write_reg(priv, XCAN_IER_OFFSET, ier);
/* Check whether it is loopback mode or normal mode */
if (priv->can.ctrlmode & CAN_CTRLMODE_LOOPBACK) {
......@@ -344,6 +418,12 @@ static int xcan_chip_start(struct net_device *ndev)
reg_sr_mask = XCAN_SR_NORMAL_MASK;
}
/* enable the first extended filter, if any, as cores with extended
* filtering default to non-receipt if all filters are disabled
*/
if (priv->devtype.flags & XCAN_FLAG_EXT_FILTERS)
priv->write_reg(priv, XCAN_AFR_EXT_OFFSET, 0x00000001);
priv->write_reg(priv, XCAN_MSR_OFFSET, reg_msr);
priv->write_reg(priv, XCAN_SRR_OFFSET, XCAN_SRR_CEN_MASK);
......@@ -439,13 +519,15 @@ static void xcan_write_frame(struct xcan_priv *priv, struct sk_buff *skb,
data[1] = be32_to_cpup((__be32 *)(cf->data + 4));
priv->write_reg(priv, XCAN_FRAME_ID_OFFSET(frame_offset), id);
/* If the CAN frame is RTR frame this write triggers transmission */
/* If the CAN frame is RTR frame this write triggers transmission
* (not on CAN FD)
*/
priv->write_reg(priv, XCAN_FRAME_DLC_OFFSET(frame_offset), dlc);
if (!(cf->can_id & CAN_RTR_FLAG)) {
priv->write_reg(priv, XCAN_FRAME_DW1_OFFSET(frame_offset),
data[0]);
/* If the CAN frame is Standard/Extended frame this
* write triggers transmission
* write triggers transmission (not on CAN FD)
*/
priv->write_reg(priv, XCAN_FRAME_DW2_OFFSET(frame_offset),
data[1]);
......@@ -488,24 +570,59 @@ static int xcan_start_xmit_fifo(struct sk_buff *skb, struct net_device *ndev)
return 0;
}
/**
* xcan_start_xmit_mailbox - Starts the transmission (mailbox mode)
*
* Return: 0 on success, -ENOSPC if there is no space
*/
static int xcan_start_xmit_mailbox(struct sk_buff *skb, struct net_device *ndev)
{
struct xcan_priv *priv = netdev_priv(ndev);
unsigned long flags;
if (unlikely(priv->read_reg(priv, XCAN_TRR_OFFSET) &
BIT(XCAN_TX_MAILBOX_IDX)))
return -ENOSPC;
can_put_echo_skb(skb, ndev, 0);
spin_lock_irqsave(&priv->tx_lock, flags);
priv->tx_head++;
xcan_write_frame(priv, skb,
XCAN_TXMSG_FRAME_OFFSET(XCAN_TX_MAILBOX_IDX));
/* Mark buffer as ready for transmit */
priv->write_reg(priv, XCAN_TRR_OFFSET, BIT(XCAN_TX_MAILBOX_IDX));
netif_stop_queue(ndev);
spin_unlock_irqrestore(&priv->tx_lock, flags);
return 0;
}
/**
* xcan_start_xmit - Starts the transmission
* @skb: sk_buff pointer that contains data to be Txed
* @ndev: Pointer to net_device structure
*
* This function is invoked from upper layers to initiate transmission. This
* function uses the next available free txbuff and populates their fields to
* start the transmission.
* This function is invoked from upper layers to initiate transmission.
*
* Return: NETDEV_TX_OK on success and NETDEV_TX_BUSY when the tx queue is full
*/
static int xcan_start_xmit(struct sk_buff *skb, struct net_device *ndev)
{
struct xcan_priv *priv = netdev_priv(ndev);
int ret;
if (can_dropped_invalid_skb(ndev, skb))
return NETDEV_TX_OK;
if (priv->devtype.flags & XCAN_FLAG_TX_MAILBOXES)
ret = xcan_start_xmit_mailbox(skb, ndev);
else
ret = xcan_start_xmit_fifo(skb, ndev);
if (ret < 0) {
......@@ -739,6 +856,17 @@ static void xcan_err_interrupt(struct net_device *ndev, u32 isr)
}
}
/* Check for RX Match Not Finished interrupt */
if (isr & XCAN_IXR_RXMNF_MASK) {
stats->rx_dropped++;
stats->rx_errors++;
netdev_err(ndev, "RX match not finished, frame discarded\n");
if (skb) {
cf->can_id |= CAN_ERR_CRTL;
cf->data[1] |= CAN_ERR_CRTL_UNSPEC;
}
}
/* Check for error interrupt */
if (isr & XCAN_IXR_ERROR_MASK) {
if (skb)
......@@ -822,6 +950,44 @@ static void xcan_state_interrupt(struct net_device *ndev, u32 isr)
priv->can.state = CAN_STATE_ERROR_ACTIVE;
}
/**
* xcan_rx_fifo_get_next_frame - Get register offset of next RX frame
*
* Return: Register offset of the next frame in RX FIFO.
*/
static int xcan_rx_fifo_get_next_frame(struct xcan_priv *priv)
{
int offset;
if (priv->devtype.flags & XCAN_FLAG_RX_FIFO_MULTI) {
u32 fsr;
/* clear RXOK before the is-empty check so that any newly
* received frame will reassert it without a race
*/
priv->write_reg(priv, XCAN_ICR_OFFSET, XCAN_IXR_RXOK_MASK);
fsr = priv->read_reg(priv, XCAN_FSR_OFFSET);
/* check if RX FIFO is empty */
if (!(fsr & XCAN_FSR_FL_MASK))
return -ENOENT;
offset = XCAN_RXMSG_FRAME_OFFSET(fsr & XCAN_FSR_RI_MASK);
} else {
/* check if RX FIFO is empty */
if (!(priv->read_reg(priv, XCAN_ISR_OFFSET) &
XCAN_IXR_RXNEMP_MASK))
return -ENOENT;
/* frames are read from a static offset */
offset = XCAN_RXFIFO_OFFSET;
}
return offset;
}
/**
* xcan_rx_poll - Poll routine for rx packets (NAPI)
* @napi: napi structure pointer
......@@ -836,14 +1002,24 @@ static int xcan_rx_poll(struct napi_struct *napi, int quota)
{
struct net_device *ndev = napi->dev;
struct xcan_priv *priv = netdev_priv(ndev);
u32 isr, ier;
u32 ier;
int work_done = 0;
int frame_offset;
isr = priv->read_reg(priv, XCAN_ISR_OFFSET);
while ((isr & XCAN_IXR_RXNEMP_MASK) && (work_done < quota)) {
work_done += xcan_rx(ndev, XCAN_RXFIFO_OFFSET);
priv->write_reg(priv, XCAN_ICR_OFFSET, XCAN_IXR_RXNEMP_MASK);
isr = priv->read_reg(priv, XCAN_ISR_OFFSET);
while ((frame_offset = xcan_rx_fifo_get_next_frame(priv)) >= 0 &&
(work_done < quota)) {
work_done += xcan_rx(ndev, frame_offset);
if (priv->devtype.flags & XCAN_FLAG_RX_FIFO_MULTI)
/* increment read index */
priv->write_reg(priv, XCAN_FSR_OFFSET,
XCAN_FSR_IRI_MASK);
else
/* clear rx-not-empty (will actually clear only if
* empty)
*/
priv->write_reg(priv, XCAN_ICR_OFFSET,
XCAN_IXR_RXNEMP_MASK);
}
if (work_done) {
......@@ -854,7 +1030,7 @@ static int xcan_rx_poll(struct napi_struct *napi, int quota)
if (work_done < quota) {
napi_complete_done(napi, work_done);
ier = priv->read_reg(priv, XCAN_IER_OFFSET);
ier |= XCAN_IXR_RXNEMP_MASK;
ier |= xcan_rx_int_mask(priv);
priv->write_reg(priv, XCAN_IER_OFFSET, ier);
}
return work_done;
......@@ -953,6 +1129,7 @@ static irqreturn_t xcan_interrupt(int irq, void *dev_id)
struct xcan_priv *priv = netdev_priv(ndev);
u32 isr, ier;
u32 isr_errors;
u32 rx_int_mask = xcan_rx_int_mask(priv);
/* Get the interrupt status from Xilinx CAN */
isr = priv->read_reg(priv, XCAN_ISR_OFFSET);
......@@ -972,16 +1149,17 @@ static irqreturn_t xcan_interrupt(int irq, void *dev_id)
/* Check for the type of error interrupt and Processing it */
isr_errors = isr & (XCAN_IXR_ERROR_MASK | XCAN_IXR_RXOFLW_MASK |
XCAN_IXR_BSOFF_MASK | XCAN_IXR_ARBLST_MASK);
XCAN_IXR_BSOFF_MASK | XCAN_IXR_ARBLST_MASK |
XCAN_IXR_RXMNF_MASK);
if (isr_errors) {
priv->write_reg(priv, XCAN_ICR_OFFSET, isr_errors);
xcan_err_interrupt(ndev, isr);
}
/* Check for the type of receive interrupt and Processing it */
if (isr & XCAN_IXR_RXNEMP_MASK) {
if (isr & rx_int_mask) {
ier = priv->read_reg(priv, XCAN_IER_OFFSET);
ier &= ~XCAN_IXR_RXNEMP_MASK;
ier &= ~rx_int_mask;
priv->write_reg(priv, XCAN_IER_OFFSET, ier);
napi_schedule(&priv->napi);
}
......@@ -1228,14 +1406,27 @@ static const struct dev_pm_ops xcan_dev_pm_ops = {
};
static const struct xcan_devtype_data xcan_zynq_data = {
.flags = XCAN_FLAG_TXFEMP,
.bittiming_const = &xcan_bittiming_const,
.btr_ts2_shift = XCAN_BTR_TS2_SHIFT,
.btr_sjw_shift = XCAN_BTR_SJW_SHIFT,
.bus_clk_name = "pclk",
};
static const struct xcan_devtype_data xcan_axi_data = {
.flags = 0,
.bittiming_const = &xcan_bittiming_const,
.btr_ts2_shift = XCAN_BTR_TS2_SHIFT,
.btr_sjw_shift = XCAN_BTR_SJW_SHIFT,
.bus_clk_name = "s_axi_aclk",
};
static const struct xcan_devtype_data xcan_canfd_data = {
.flags = XCAN_FLAG_EXT_FILTERS |
XCAN_FLAG_RXMNF |
XCAN_FLAG_TX_MAILBOXES |
XCAN_FLAG_RX_FIFO_MULTI,
.bittiming_const = &xcan_bittiming_const,
.btr_ts2_shift = XCAN_BTR_TS2_SHIFT_CANFD,
.btr_sjw_shift = XCAN_BTR_SJW_SHIFT_CANFD,
.bus_clk_name = "s_axi_aclk",
};
......@@ -1243,6 +1434,7 @@ static const struct xcan_devtype_data xcan_axi_data = {
static const struct of_device_id xcan_of_match[] = {
{ .compatible = "xlnx,zynq-can-1.0", .data = &xcan_zynq_data },
{ .compatible = "xlnx,axi-can-1.00.a", .data = &xcan_axi_data },
{ .compatible = "xlnx,canfd-1.0", .data = &xcan_canfd_data },
{ /* end of list */ },
};
MODULE_DEVICE_TABLE(of, xcan_of_match);
......@@ -1264,7 +1456,10 @@ static int xcan_probe(struct platform_device *pdev)
const struct of_device_id *of_id;
const struct xcan_devtype_data *devtype = &xcan_axi_data;
void __iomem *addr;
int ret, rx_max, tx_max, tx_fifo_depth;
int ret;
int rx_max, tx_max;
int hw_tx_max, hw_rx_max;
const char *hw_tx_max_property;
/* Get the virtual base address for the device */
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
......@@ -1274,21 +1469,33 @@ static int xcan_probe(struct platform_device *pdev)
goto err;
}
ret = of_property_read_u32(pdev->dev.of_node, "tx-fifo-depth",
&tx_fifo_depth);
if (ret < 0)
goto err;
ret = of_property_read_u32(pdev->dev.of_node, "rx-fifo-depth", &rx_max);
if (ret < 0)
goto err;
of_id = of_match_device(xcan_of_match, &pdev->dev);
if (of_id && of_id->data)
devtype = of_id->data;
/* There is no way to directly figure out how many frames have been
* sent when the TXOK interrupt is processed. If watermark programming
hw_tx_max_property = devtype->flags & XCAN_FLAG_TX_MAILBOXES ?
"tx-mailbox-count" : "tx-fifo-depth";
ret = of_property_read_u32(pdev->dev.of_node, hw_tx_max_property,
&hw_tx_max);
if (ret < 0) {
dev_err(&pdev->dev, "missing %s property\n",
hw_tx_max_property);
goto err;
}
ret = of_property_read_u32(pdev->dev.of_node, "rx-fifo-depth",
&hw_rx_max);
if (ret < 0) {
dev_err(&pdev->dev,
"missing rx-fifo-depth property (mailbox mode is not supported)\n");
goto err;
}
/* With TX FIFO:
*
* There is no way to directly figure out how many frames have been
* sent when the TXOK interrupt is processed. If TXFEMP
* is supported, we can have 2 frames in the FIFO and use TXFEMP
* to determine if 1 or 2 frames have been sent.
* Theoretically we should be able to use TXFWMEMP to determine up
......@@ -1297,12 +1504,20 @@ static int xcan_probe(struct platform_device *pdev)
* than 2 frames in FIFO) is set anyway with no TXOK (a frame was
* sent), which is not a sensible state - possibly TXFWMEMP is not
* completely synchronized with the rest of the bits?
*
* With TX mailboxes:
*
* HW sends frames in CAN ID priority order. To preserve FIFO ordering
* we submit frames one at a time.
*/
if (devtype->flags & XCAN_FLAG_TXFEMP)
tx_max = min(tx_fifo_depth, 2);
if (!(devtype->flags & XCAN_FLAG_TX_MAILBOXES) &&
(devtype->flags & XCAN_FLAG_TXFEMP))
tx_max = min(hw_tx_max, 2);
else
tx_max = 1;
rx_max = hw_rx_max;
/* Create a CAN device instance */
ndev = alloc_candev(sizeof(struct xcan_priv), tx_max);
if (!ndev)
......@@ -1373,9 +1588,9 @@ static int xcan_probe(struct platform_device *pdev)
pm_runtime_put(&pdev->dev);
netdev_dbg(ndev, "reg_base=0x%p irq=%d clock=%d, tx fifo depth: actual %d, using %d\n",
netdev_dbg(ndev, "reg_base=0x%p irq=%d clock=%d, tx buffers: actual %d, using %d\n",
priv->reg_base, ndev->irq, priv->can.clock.freq,
tx_fifo_depth, priv->tx_max);
hw_tx_max, priv->tx_max);
return 0;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment