Skip to content

L
linux
Commit 9f37e90e authored by Tero Kristo's avatar Tero Kristo
Browse files
Options

clk: ti: dflt: move support for default gate clock to clock driver 

With the legacy support gone, OMAP2+ default gate clock can be moved
under clock driver. Create a new file for the purpose, and clean-up
the header exports a bit as some clock APIs are no longer needed
outside clock driver itself.
Signed-off-by: default avatarTero Kristo <t-kristo@ti.com>
parent 046b7c31
Hide whitespace changes
Inline Side-by-side
Showing with 322 additions and 278 deletions
arch/arm/mach-omap2/clock.c
View file @ 9f37e90e
......@@ -40,12 +40,6 @@
#include "cm-regbits-34xx.h"
#include "common.h"
/*
* MAX_MODULE_ENABLE_WAIT: maximum of number of microseconds to wait
* for a module to indicate that it is no longer in idle
*/
#define MAX_MODULE_ENABLE_WAIT 100000
u16 cpu_mask;
/* DPLL valid Fint frequency band limits - from 34xx TRM Section 4.7.6.2 */
......@@ -176,77 +170,6 @@ void __init omap2_clk_legacy_provider_init(int index, void __iomem *mem)
/* Private functions */
/**
* _wait_idlest_generic - wait for a module to leave the idle state
* @clk: module clock to wait for (needed for register offsets)
* @reg: virtual address of module IDLEST register
* @mask: value to mask against to determine if the module is active
* @idlest: idle state indicator (0 or 1) for the clock
* @name: name of the clock (for printk)
*
* Wait for a module to leave idle, where its idle-status register is
* not inside the CM module. Returns 1 if the module left idle
* promptly, or 0 if the module did not leave idle before the timeout
* elapsed. XXX Deprecated - should be moved into drivers for the
* individual IP block that the IDLEST register exists in.
*/
static int _wait_idlest_generic(struct clk_hw_omap *clk, void __iomem *reg,
u32 mask, u8 idlest, const char *name)
{
int i = 0, ena = 0;
ena = (idlest) ? 0 : mask;
omap_test_timeout(((omap2_clk_readl(clk, reg) & mask) == ena),
MAX_MODULE_ENABLE_WAIT, i);
if (i < MAX_MODULE_ENABLE_WAIT)
pr_debug("omap clock: module associated with clock %s ready after %d loops\n",
name, i);
else
pr_err("omap clock: module associated with clock %s didn't enable in %d tries\n",
name, MAX_MODULE_ENABLE_WAIT);
return (i < MAX_MODULE_ENABLE_WAIT) ? 1 : 0;
};
/**
* _omap2_module_wait_ready - wait for an OMAP module to leave IDLE
* @clk: struct clk * belonging to the module
*
* If the necessary clocks for the OMAP hardware IP block that
* corresponds to clock @clk are enabled, then wait for the module to
* indicate readiness (i.e., to leave IDLE). This code does not
* belong in the clock code and will be moved in the medium term to
* module-dependent code. No return value.
*/
static void _omap2_module_wait_ready(struct clk_hw_omap *clk)
{
void __iomem *companion_reg, *idlest_reg;
u8 other_bit, idlest_bit, idlest_val, idlest_reg_id;
s16 prcm_mod;
int r;
/* Not all modules have multiple clocks that their IDLEST depends on */
if (clk->ops->find_companion) {
clk->ops->find_companion(clk, &companion_reg, &other_bit);
if (!(omap2_clk_readl(clk, companion_reg) & (1 << other_bit)))
return;
}
clk->ops->find_idlest(clk, &idlest_reg, &idlest_bit, &idlest_val);
r = cm_split_idlest_reg(idlest_reg, &prcm_mod, &idlest_reg_id);
if (r) {
/* IDLEST register not in the CM module */
_wait_idlest_generic(clk, idlest_reg, (1 << idlest_bit),
idlest_val, __clk_get_name(clk->hw.clk));
} else {
omap_cm_wait_module_ready(0, prcm_mod, idlest_reg_id,
idlest_bit);
};
}
/* Public functions */
/**
......@@ -279,174 +202,6 @@ void omap2_init_clk_clkdm(struct clk_hw *hw)
}
}
/**
* omap2_clk_dflt_find_companion - find companion clock to @clk
* @clk: struct clk * to find the companion clock of
* @other_reg: void __iomem ** to return the companion clock CM_*CLKEN va in
* @other_bit: u8 ** to return the companion clock bit shift in
*
* Note: We don't need special code here for INVERT_ENABLE for the
* time being since INVERT_ENABLE only applies to clocks enabled by
* CM_CLKEN_PLL
*
* Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes it's
* just a matter of XORing the bits.
*
* Some clocks don't have companion clocks. For example, modules with
* only an interface clock (such as MAILBOXES) don't have a companion
* clock. Right now, this code relies on the hardware exporting a bit
* in the correct companion register that indicates that the
* nonexistent 'companion clock' is active. Future patches will
* associate this type of code with per-module data structures to
* avoid this issue, and remove the casts. No return value.
*/
void omap2_clk_dflt_find_companion(struct clk_hw_omap *clk,
void __iomem **other_reg, u8 *other_bit)
{
u32 r;
/*
* Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes
* it's just a matter of XORing the bits.
*/
r = ((__force u32)clk->enable_reg ^ (CM_FCLKEN ^ CM_ICLKEN));
*other_reg = (__force void __iomem *)r;
*other_bit = clk->enable_bit;
}
/**
* omap2_clk_dflt_find_idlest - find CM_IDLEST reg va, bit shift for @clk
* @clk: struct clk * to find IDLEST info for
* @idlest_reg: void __iomem ** to return the CM_IDLEST va in
* @idlest_bit: u8 * to return the CM_IDLEST bit shift in
* @idlest_val: u8 * to return the idle status indicator
*
* Return the CM_IDLEST register address and bit shift corresponding
* to the module that "owns" this clock. This default code assumes
* that the CM_IDLEST bit shift is the CM_*CLKEN bit shift, and that
* the IDLEST register address ID corresponds to the CM_*CLKEN
* register address ID (e.g., that CM_FCLKEN2 corresponds to
* CM_IDLEST2). This is not true for all modules. No return value.
*/
void omap2_clk_dflt_find_idlest(struct clk_hw_omap *clk,
void __iomem **idlest_reg, u8 *idlest_bit, u8 *idlest_val)
{
u32 r;
r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
*idlest_reg = (__force void __iomem *)r;
*idlest_bit = clk->enable_bit;
/*
* 24xx uses 0 to indicate not ready, and 1 to indicate ready.
* 34xx reverses this, just to keep us on our toes
* AM35xx uses both, depending on the module.
*/
*idlest_val = ti_clk_get_features()->cm_idlest_val;
}
/**
* omap2_dflt_clk_enable - enable a clock in the hardware
* @hw: struct clk_hw * of the clock to enable
*
* Enable the clock @hw in the hardware. We first call into the OMAP
* clockdomain code to "enable" the corresponding clockdomain if this
* is the first enabled user of the clockdomain. Then program the
* hardware to enable the clock. Then wait for the IP block that uses
* this clock to leave idle (if applicable). Returns the error value
* from clkdm_clk_enable() if it terminated with an error, or -EINVAL
* if @hw has a null clock enable_reg, or zero upon success.
*/
int omap2_dflt_clk_enable(struct clk_hw *hw)
{
struct clk_hw_omap *clk;
u32 v;
int ret = 0;
bool clkdm_control;
if (ti_clk_get_features()->flags & TI_CLK_DISABLE_CLKDM_CONTROL)
clkdm_control = false;
else
clkdm_control = true;
clk = to_clk_hw_omap(hw);
if (clkdm_control && clk->clkdm) {
ret = clkdm_clk_enable(clk->clkdm, hw->clk);
if (ret) {
WARN(1, "%s: could not enable %s's clockdomain %s: %d\n",
__func__, __clk_get_name(hw->clk),
clk->clkdm->name, ret);
return ret;
}
}
if (unlikely(clk->enable_reg == NULL)) {
pr_err("%s: %s missing enable_reg\n", __func__,
__clk_get_name(hw->clk));
ret = -EINVAL;
goto err;
}
/* FIXME should not have INVERT_ENABLE bit here */
v = omap2_clk_readl(clk, clk->enable_reg);
if (clk->flags & INVERT_ENABLE)
v &= ~(1 << clk->enable_bit);
else
v |= (1 << clk->enable_bit);
omap2_clk_writel(v, clk, clk->enable_reg);
v = omap2_clk_readl(clk, clk->enable_reg); /* OCP barrier */
if (clk->ops && clk->ops->find_idlest)
_omap2_module_wait_ready(clk);
return 0;
err:
if (clkdm_control && clk->clkdm)
clkdm_clk_disable(clk->clkdm, hw->clk);
return ret;
}
/**
* omap2_dflt_clk_disable - disable a clock in the hardware
* @hw: struct clk_hw * of the clock to disable
*
* Disable the clock @hw in the hardware, and call into the OMAP
* clockdomain code to "disable" the corresponding clockdomain if all
* clocks/hwmods in that clockdomain are now disabled. No return
* value.
*/
void omap2_dflt_clk_disable(struct clk_hw *hw)
{
struct clk_hw_omap *clk;
u32 v;
clk = to_clk_hw_omap(hw);
if (!clk->enable_reg) {
/*
* 'independent' here refers to a clock which is not
* controlled by its parent.
*/
pr_err("%s: independent clock %s has no enable_reg\n",
__func__, __clk_get_name(hw->clk));
return;
}
v = omap2_clk_readl(clk, clk->enable_reg);
if (clk->flags & INVERT_ENABLE)
v |= (1 << clk->enable_bit);
else
v &= ~(1 << clk->enable_bit);
omap2_clk_writel(v, clk, clk->enable_reg);
/* No OCP barrier needed here since it is a disable operation */
if (!(ti_clk_get_features()->flags & TI_CLK_DISABLE_CLKDM_CONTROL) &&
clk->clkdm)
clkdm_clk_disable(clk->clkdm, hw->clk);
}
/**
* omap2_clkops_enable_clkdm - increment usecount on clkdm of @hw
* @hw: struct clk_hw * of the clock being enabled
......@@ -523,29 +278,6 @@ void omap2_clkops_disable_clkdm(struct clk_hw *hw)
clkdm_clk_disable(clk->clkdm, hw->clk);
}
/**
* omap2_dflt_clk_is_enabled - is clock enabled in the hardware?
* @hw: struct clk_hw * to check
*
* Return 1 if the clock represented by @hw is enabled in the
* hardware, or 0 otherwise. Intended for use in the struct
* clk_ops.is_enabled function pointer.
*/
int omap2_dflt_clk_is_enabled(struct clk_hw *hw)
{
struct clk_hw_omap *clk = to_clk_hw_omap(hw);
u32 v;
v = omap2_clk_readl(clk, clk->enable_reg);
if (clk->flags & INVERT_ENABLE)
v ^= BIT(clk->enable_bit);
v &= BIT(clk->enable_bit);
return v ? 1 : 0;
}
static int __initdata mpurate;
/*
......@@ -566,11 +298,6 @@ static int __init omap_clk_setup(char *str)
}
__setup("mpurate=", omap_clk_setup);
const struct clk_hw_omap_ops clkhwops_wait = {
.find_idlest = omap2_clk_dflt_find_idlest,
.find_companion = omap2_clk_dflt_find_companion,
};
/**
* omap2_clk_print_new_rates - print summary of current clock tree rates
* @hfclkin_ck_name: clk name for the off-chip HF oscillator
......
drivers/clk/ti/Makefile
View file @ 9f37e90e
obj-y += clk.o autoidle.o clockdomain.o
clk-common = dpll.o composite.o divider.o gate.o \
fixed-factor.o mux.o apll.o \
clkt_dpll.o clkt_iclk.o
clkt_dpll.o clkt_iclk.o clkt_dflt.o
obj-$(CONFIG_SOC_AM33XX) += $(clk-common) clk-33xx.o dpll3xxx.o
obj-$(CONFIG_SOC_TI81XX) += $(clk-common) fapll.o clk-816x.o
obj-$(CONFIG_ARCH_OMAP2) += $(clk-common) interface.o clk-2xxx.o
......
drivers/clk/ti/clkt_dflt.c 0 → 100644
View file @ 9f37e90e
/*
* Default clock type
*
* Copyright (C) 2005-2008, 2015 Texas Instruments, Inc.
* Copyright (C) 2004-2010 Nokia Corporation
*
* Contacts:
* Richard Woodruff <r-woodruff2@ti.com>
* Paul Walmsley
* Tero Kristo <t-kristo@ti.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This program is distributed "as is" WITHOUT ANY WARRANTY of any
* kind, whether express or implied; without even the implied warranty
* of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/kernel.h>
#include <linux/errno.h>
#include <linux/clk-provider.h>
#include <linux/io.h>
#include <linux/clk/ti.h>
#include <linux/delay.h>
#include "clock.h"
/*
* MAX_MODULE_ENABLE_WAIT: maximum of number of microseconds to wait
* for a module to indicate that it is no longer in idle
*/
#define MAX_MODULE_ENABLE_WAIT 100000
/*
* CM module register offsets, used for calculating the companion
* register addresses.
*/
#define CM_FCLKEN 0x0000
#define CM_ICLKEN 0x0010
/**
* _wait_idlest_generic - wait for a module to leave the idle state
* @clk: module clock to wait for (needed for register offsets)
* @reg: virtual address of module IDLEST register
* @mask: value to mask against to determine if the module is active
* @idlest: idle state indicator (0 or 1) for the clock
* @name: name of the clock (for printk)
*
* Wait for a module to leave idle, where its idle-status register is
* not inside the CM module. Returns 1 if the module left idle
* promptly, or 0 if the module did not leave idle before the timeout
* elapsed. XXX Deprecated - should be moved into drivers for the
* individual IP block that the IDLEST register exists in.
*/
static int _wait_idlest_generic(struct clk_hw_omap *clk, void __iomem *reg,
u32 mask, u8 idlest, const char *name)
{
int i = 0, ena = 0;
ena = (idlest) ? 0 : mask;
/* Wait until module enters enabled state */
for (i = 0; i < MAX_MODULE_ENABLE_WAIT; i++) {
if ((ti_clk_ll_ops->clk_readl(reg) & mask) == ena)
break;
udelay(1);
}
if (i < MAX_MODULE_ENABLE_WAIT)
pr_debug("omap clock: module associated with clock %s ready after %d loops\n",
name, i);
else
pr_err("omap clock: module associated with clock %s didn't enable in %d tries\n",
name, MAX_MODULE_ENABLE_WAIT);
return (i < MAX_MODULE_ENABLE_WAIT) ? 1 : 0;
}
/**
* _omap2_module_wait_ready - wait for an OMAP module to leave IDLE
* @clk: struct clk * belonging to the module
*
* If the necessary clocks for the OMAP hardware IP block that
* corresponds to clock @clk are enabled, then wait for the module to
* indicate readiness (i.e., to leave IDLE). This code does not
* belong in the clock code and will be moved in the medium term to
* module-dependent code. No return value.
*/
static void _omap2_module_wait_ready(struct clk_hw_omap *clk)
{
void __iomem *companion_reg, *idlest_reg;
u8 other_bit, idlest_bit, idlest_val, idlest_reg_id;
s16 prcm_mod;
int r;
/* Not all modules have multiple clocks that their IDLEST depends on */
if (clk->ops->find_companion) {
clk->ops->find_companion(clk, &companion_reg, &other_bit);
if (!(ti_clk_ll_ops->clk_readl(companion_reg) &
(1 << other_bit)))
return;
}
clk->ops->find_idlest(clk, &idlest_reg, &idlest_bit, &idlest_val);
r = ti_clk_ll_ops->cm_split_idlest_reg(idlest_reg, &prcm_mod,
&idlest_reg_id);
if (r) {
/* IDLEST register not in the CM module */
_wait_idlest_generic(clk, idlest_reg, (1 << idlest_bit),
idlest_val, __clk_get_name(clk->hw.clk));
} else {
ti_clk_ll_ops->cm_wait_module_ready(0, prcm_mod, idlest_reg_id,
idlest_bit);
}
}
/**
* omap2_clk_dflt_find_companion - find companion clock to @clk
* @clk: struct clk * to find the companion clock of
* @other_reg: void __iomem ** to return the companion clock CM_*CLKEN va in
* @other_bit: u8 ** to return the companion clock bit shift in
*
* Note: We don't need special code here for INVERT_ENABLE for the
* time being since INVERT_ENABLE only applies to clocks enabled by
* CM_CLKEN_PLL
*
* Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes it's
* just a matter of XORing the bits.
*
* Some clocks don't have companion clocks. For example, modules with
* only an interface clock (such as MAILBOXES) don't have a companion
* clock. Right now, this code relies on the hardware exporting a bit
* in the correct companion register that indicates that the
* nonexistent 'companion clock' is active. Future patches will
* associate this type of code with per-module data structures to
* avoid this issue, and remove the casts. No return value.
*/
void omap2_clk_dflt_find_companion(struct clk_hw_omap *clk,
void __iomem **other_reg, u8 *other_bit)
{
u32 r;
/*
* Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes
* it's just a matter of XORing the bits.
*/
r = ((__force u32)clk->enable_reg ^ (CM_FCLKEN ^ CM_ICLKEN));
*other_reg = (__force void __iomem *)r;
*other_bit = clk->enable_bit;
}
/**
* omap2_clk_dflt_find_idlest - find CM_IDLEST reg va, bit shift for @clk
* @clk: struct clk * to find IDLEST info for
* @idlest_reg: void __iomem ** to return the CM_IDLEST va in
* @idlest_bit: u8 * to return the CM_IDLEST bit shift in
* @idlest_val: u8 * to return the idle status indicator
*
* Return the CM_IDLEST register address and bit shift corresponding
* to the module that "owns" this clock. This default code assumes
* that the CM_IDLEST bit shift is the CM_*CLKEN bit shift, and that
* the IDLEST register address ID corresponds to the CM_*CLKEN
* register address ID (e.g., that CM_FCLKEN2 corresponds to
* CM_IDLEST2). This is not true for all modules. No return value.
*/
void omap2_clk_dflt_find_idlest(struct clk_hw_omap *clk,
void __iomem **idlest_reg, u8 *idlest_bit,
u8 *idlest_val)
{
u32 r;
r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
*idlest_reg = (__force void __iomem *)r;
*idlest_bit = clk->enable_bit;
/*
* 24xx uses 0 to indicate not ready, and 1 to indicate ready.
* 34xx reverses this, just to keep us on our toes
* AM35xx uses both, depending on the module.
*/
*idlest_val = ti_clk_get_features()->cm_idlest_val;
}
/**
* omap2_dflt_clk_enable - enable a clock in the hardware
* @hw: struct clk_hw * of the clock to enable
*
* Enable the clock @hw in the hardware. We first call into the OMAP
* clockdomain code to "enable" the corresponding clockdomain if this
* is the first enabled user of the clockdomain. Then program the
* hardware to enable the clock. Then wait for the IP block that uses
* this clock to leave idle (if applicable). Returns the error value
* from clkdm_clk_enable() if it terminated with an error, or -EINVAL
* if @hw has a null clock enable_reg, or zero upon success.
*/
int omap2_dflt_clk_enable(struct clk_hw *hw)
{
struct clk_hw_omap *clk;
u32 v;
int ret = 0;
bool clkdm_control;
if (ti_clk_get_features()->flags & TI_CLK_DISABLE_CLKDM_CONTROL)
clkdm_control = false;
else
clkdm_control = true;
clk = to_clk_hw_omap(hw);
if (clkdm_control && clk->clkdm) {
ret = ti_clk_ll_ops->clkdm_clk_enable(clk->clkdm, hw->clk);
if (ret) {
WARN(1,
"%s: could not enable %s's clockdomain %s: %d\n",
__func__, __clk_get_name(hw->clk),
clk->clkdm_name, ret);
return ret;
}
}
if (unlikely(!clk->enable_reg)) {
pr_err("%s: %s missing enable_reg\n", __func__,
__clk_get_name(hw->clk));
ret = -EINVAL;
goto err;
}
/* FIXME should not have INVERT_ENABLE bit here */
v = ti_clk_ll_ops->clk_readl(clk->enable_reg);
if (clk->flags & INVERT_ENABLE)
v &= ~(1 << clk->enable_bit);
else
v |= (1 << clk->enable_bit);
ti_clk_ll_ops->clk_writel(v, clk->enable_reg);
v = ti_clk_ll_ops->clk_readl(clk->enable_reg); /* OCP barrier */
if (clk->ops && clk->ops->find_idlest)
_omap2_module_wait_ready(clk);
return 0;
err:
if (clkdm_control && clk->clkdm)
ti_clk_ll_ops->clkdm_clk_disable(clk->clkdm, hw->clk);
return ret;
}
/**
* omap2_dflt_clk_disable - disable a clock in the hardware
* @hw: struct clk_hw * of the clock to disable
*
* Disable the clock @hw in the hardware, and call into the OMAP
* clockdomain code to "disable" the corresponding clockdomain if all
* clocks/hwmods in that clockdomain are now disabled. No return
* value.
*/
void omap2_dflt_clk_disable(struct clk_hw *hw)
{
struct clk_hw_omap *clk;
u32 v;
clk = to_clk_hw_omap(hw);
if (!clk->enable_reg) {
/*
* 'independent' here refers to a clock which is not
* controlled by its parent.
*/
pr_err("%s: independent clock %s has no enable_reg\n",
__func__, __clk_get_name(hw->clk));
return;
}
v = ti_clk_ll_ops->clk_readl(clk->enable_reg);
if (clk->flags & INVERT_ENABLE)
v |= (1 << clk->enable_bit);
else
v &= ~(1 << clk->enable_bit);
ti_clk_ll_ops->clk_writel(v, clk->enable_reg);
/* No OCP barrier needed here since it is a disable operation */
if (!(ti_clk_get_features()->flags & TI_CLK_DISABLE_CLKDM_CONTROL) &&
clk->clkdm)
ti_clk_ll_ops->clkdm_clk_disable(clk->clkdm, hw->clk);
}
/**
* omap2_dflt_clk_is_enabled - is clock enabled in the hardware?
* @hw: struct clk_hw * to check
*
* Return 1 if the clock represented by @hw is enabled in the
* hardware, or 0 otherwise. Intended for use in the struct
* clk_ops.is_enabled function pointer.
*/
int omap2_dflt_clk_is_enabled(struct clk_hw *hw)
{
struct clk_hw_omap *clk = to_clk_hw_omap(hw);
u32 v;
v = ti_clk_ll_ops->clk_readl(clk->enable_reg);
if (clk->flags & INVERT_ENABLE)
v ^= BIT(clk->enable_bit);
v &= BIT(clk->enable_bit);
return v ? 1 : 0;
}
const struct clk_hw_omap_ops clkhwops_wait = {
.find_idlest = omap2_clk_dflt_find_idlest,
.find_companion = omap2_clk_dflt_find_companion,
};
drivers/clk/ti/clock.h
View file @ 9f37e90e
......@@ -175,9 +175,14 @@ void omap2_clk_enable_init_clocks(const char **clk_names, u8 num_clocks);
extern const struct clk_hw_omap_ops clkhwops_omap3_dpll;
extern const struct clk_hw_omap_ops clkhwops_omap4_dpllmx;
extern const struct clk_hw_omap_ops clkhwops_wait;
extern const struct clk_hw_omap_ops clkhwops_iclk;
extern const struct clk_hw_omap_ops clkhwops_iclk_wait;
int omap2_dflt_clk_enable(struct clk_hw *hw);
void omap2_dflt_clk_disable(struct clk_hw *hw);
int omap2_dflt_clk_is_enabled(struct clk_hw *hw);
u8 omap2_init_dpll_parent(struct clk_hw *hw);
int omap3_noncore_dpll_enable(struct clk_hw *hw);
void omap3_noncore_dpll_disable(struct clk_hw *hw);
......
include/linux/clk/ti.h
View file @ 9f37e90e
......@@ -278,9 +278,6 @@ int omap2_clk_disable_autoidle_all(void);
int omap2_clk_enable_autoidle_all(void);
int omap2_clk_allow_idle(struct clk *clk);
int omap2_clk_deny_idle(struct clk *clk);
int omap2_dflt_clk_enable(struct clk_hw *hw);
void omap2_dflt_clk_disable(struct clk_hw *hw);
int omap2_dflt_clk_is_enabled(struct clk_hw *hw);
void omap2_clkt_iclk_allow_idle(struct clk_hw_omap *clk);
void omap2_clkt_iclk_deny_idle(struct clk_hw_omap *clk);
void omap2_clk_dflt_find_companion(struct clk_hw_omap *clk,
......@@ -337,7 +334,6 @@ const struct ti_clk_features *ti_clk_get_features(void);
extern const struct clk_hw_omap_ops clkhwops_omap2xxx_dpll;
extern const struct clk_hw_omap_ops clkhwops_omap2430_i2chs_wait;
extern const struct clk_hw_omap_ops clkhwops_wait;
extern const struct clk_hw_omap_ops clkhwops_omap3430es2_dss_usbhost_wait;
extern const struct clk_hw_omap_ops clkhwops_am35xx_ipss_module_wait;
extern const struct clk_hw_omap_ops clkhwops_am35xx_ipss_wait;
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7