serial: 8250: Add new port type for TI DA8xx/66AK2x

This adds a new UART port type for TI DA8xx/OMAPL13x/AM17xx/AM18xx/66AK2x.
These SoCs have standard 8250 registers plus some extra non-standard
registers.

The UART will not function unless the non-standard Power and Emulation
Management Register (PWREMU_MGMT) is configured correctly. This is
currently handled in arch/arm/mach-davinci/serial.c for non-device-tree
boards. Making this part of the UART driver will allow UART to work on
device-tree boards as well and the mach code can eventually be removed.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/tty/serial/8250/8250_of.c

@@ -332,6 +332,7 @@ static const struct of_device_id of_platform_serial_table[] = {
 		.data = (void *)PORT_ALTR_16550_F128, },
 	{ .compatible = "mrvl,mmp-uart",
 		.data = (void *)PORT_XSCALE, },
+	{ .compatible = "ti,da830-uart", .data = (void *)PORT_DA830, },
 	{ /* end of list */ },
 };
 MODULE_DEVICE_TABLE(of, of_platform_serial_table);

drivers/tty/serial/8250/8250_port.c

@@ -273,6 +273,15 @@ static const struct serial8250_config uart_config[] = {
 		.rxtrig_bytes	= {1, 4, 8, 14},
 		.flags		= UART_CAP_FIFO,
 	},
+	[PORT_DA830] = {
+		.name		= "TI DA8xx/66AK2x",
+		.fifo_size	= 16,
+		.tx_loadsz	= 16,
+		.fcr		= UART_FCR_DMA_SELECT | UART_FCR_ENABLE_FIFO |
+				  UART_FCR_R_TRIG_10,
+		.rxtrig_bytes	= {1, 4, 8, 14},
+		.flags		= UART_CAP_FIFO | UART_CAP_AFE,
+	},
 };
 
 /* Uart divisor latch read */
@@ -2114,6 +2123,19 @@ int serial8250_do_startup(struct uart_port *port)
 		serial_port_out(port, UART_LCR, 0);
 	}
 
+	if (port->type == PORT_DA830) {
+		/* Reset the port */
+		serial_port_out(port, UART_IER, 0);
+		serial_port_out(port, UART_DA830_PWREMU_MGMT, 0);
+		mdelay(10);
+
+		/* Enable Tx, Rx and free run mode */
+		serial_port_out(port, UART_DA830_PWREMU_MGMT,
+				UART_DA830_PWREMU_MGMT_UTRST |
+				UART_DA830_PWREMU_MGMT_URRST |
+				UART_DA830_PWREMU_MGMT_FREE);
+	}
+
 #ifdef CONFIG_SERIAL_8250_RSA
 	/*
 	 * If this is an RSA port, see if we can kick it up to the

include/uapi/linux/serial_core.h

@@ -56,7 +56,8 @@
 #define PORT_ALTR_16550_F128 28 /* Altera 16550 UART with 128 FIFOs */
 #define PORT_RT2880	29	/* Ralink RT2880 internal UART */
 #define PORT_16550A_FSL64 30	/* Freescale 16550 UART with 64 FIFOs */
-#define PORT_MAX_8250	30	/* max port ID */
+#define PORT_DA830	31	/* TI DA8xx/66AK2x */
+#define PORT_MAX_8250	31	/* max port ID */
 
 /*
  * ARM specific type numbers.  These are not currently guaranteed

include/uapi/linux/serial_reg.h

@@ -327,6 +327,14 @@
 #define SERIAL_RSA_BAUD_BASE (921600)
 #define SERIAL_RSA_BAUD_BASE_LO (SERIAL_RSA_BAUD_BASE / 8)
 
+/* Extra registers for TI DA8xx/66AK2x */
+#define UART_DA830_PWREMU_MGMT	12
+
+/* PWREMU_MGMT register bits */
+#define UART_DA830_PWREMU_MGMT_FREE	(1 << 0)  /* Free-running mode */
+#define UART_DA830_PWREMU_MGMT_URRST	(1 << 13) /* Receiver reset/enable */
+#define UART_DA830_PWREMU_MGMT_UTRST	(1 << 14) /* Transmitter reset/enable */
+
 /*
  * Extra serial register definitions for the internal UARTs
  * in TI OMAP processors.