Merge branch 'upstream-next-davem' of...

Merge branch 'upstream-next-davem' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6

Documentation/networking/bonding.txt

@@ -289,35 +289,73 @@ downdelay
 fail_over_mac
 
 	Specifies whether active-backup mode should set all slaves to
-	the same MAC address (the traditional behavior), or, when
-	enabled, change the bond's MAC address when changing the
-	active interface (i.e., fail over the MAC address itself).
-
-	Fail over MAC is useful for devices that cannot ever alter
-	their MAC address, or for devices that refuse incoming
-	broadcasts with their own source MAC (which interferes with
-	the ARP monitor).
-
-	The down side of fail over MAC is that every device on the
-	network must be updated via gratuitous ARP, vs. just updating
-	a switch or set of switches (which often takes place for any
-	traffic, not just ARP traffic, if the switch snoops incoming
-	traffic to update its tables) for the traditional method.  If
-	the gratuitous ARP is lost, communication may be disrupted.
-
-	When fail over MAC is used in conjuction with the mii monitor,
-	devices which assert link up prior to being able to actually
-	transmit and receive are particularly susecptible to loss of
-	the gratuitous ARP, and an appropriate updelay setting may be
-	required.
-
-	A value of 0 disables fail over MAC, and is the default.  A
-	value of 1 enables fail over MAC.  This option is enabled
-	automatically if the first slave added cannot change its MAC
-	address.  This option may be modified via sysfs only when no
-	slaves are present in the bond.
-
-	This option was added in bonding version 3.2.0.
+	the same MAC address at enslavement (the traditional
+	behavior), or, when enabled, perform special handling of the
+	bond's MAC address in accordance with the selected policy.
+
+	Possible values are:
+
+	none or 0
+
+		This setting disables fail_over_mac, and causes
+		bonding to set all slaves of an active-backup bond to
+		the same MAC address at enslavement time.  This is the
+		default.
+
+	active or 1
+
+		The "active" fail_over_mac policy indicates that the
+		MAC address of the bond should always be the MAC
+		address of the currently active slave.  The MAC
+		address of the slaves is not changed; instead, the MAC
+		address of the bond changes during a failover.
+
+		This policy is useful for devices that cannot ever
+		alter their MAC address, or for devices that refuse
+		incoming broadcasts with their own source MAC (which
+		interferes with the ARP monitor).
+
+		The down side of this policy is that every device on
+		the network must be updated via gratuitous ARP,
+		vs. just updating a switch or set of switches (which
+		often takes place for any traffic, not just ARP
+		traffic, if the switch snoops incoming traffic to
+		update its tables) for the traditional method.  If the
+		gratuitous ARP is lost, communication may be
+		disrupted.
+
+		When this policy is used in conjuction with the mii
+		monitor, devices which assert link up prior to being
+		able to actually transmit and receive are particularly
+		susecptible to loss of the gratuitous ARP, and an
+		appropriate updelay setting may be required.
+
+	follow or 2
+
+		The "follow" fail_over_mac policy causes the MAC
+		address of the bond to be selected normally (normally
+		the MAC address of the first slave added to the bond).
+		However, the second and subsequent slaves are not set
+		to this MAC address while they are in a backup role; a
+		slave is programmed with the bond's MAC address at
+		failover time (and the formerly active slave receives
+		the newly active slave's MAC address).
+
+		This policy is useful for multiport devices that
+		either become confused or incur a performance penalty
+		when multiple ports are programmed with the same MAC
+		address.
+
+
+	The default policy is none, unless the first slave cannot
+	change its MAC address, in which case the active policy is
+	selected by default.
+
+	This option may be modified via sysfs only when no slaves are
+	present in the bond.
+
+	This option was added in bonding version 3.2.0.  The "follow"
+	policy was added in bonding version 3.3.0.
 
 lacp_rate
 

drivers/net/3c509.c

@@ -413,7 +413,7 @@ static int __devinit el3_pnp_probe(struct pnp_dev *pdev,
 {
 	short i;
 	int ioaddr, irq, if_port;
-	u16 phys_addr[3];
+	__be16 phys_addr[3];
 	struct net_device *dev = NULL;
 	int err;
 
@@ -605,7 +605,7 @@ static int __init el3_mca_probe(struct device *device)
 
 	short i;
 	int ioaddr, irq, if_port;
-	u16 phys_addr[3];
+	__be16 phys_addr[3];
 	struct net_device *dev = NULL;
 	u_char pos4, pos5;
 	struct mca_device *mdev = to_mca_device(device);
@@ -635,9 +635,8 @@ static int __init el3_mca_probe(struct device *device)
 			printk(KERN_DEBUG "3c529: irq %d  ioaddr 0x%x  ifport %d\n", irq, ioaddr, if_port);
 	}
 	EL3WINDOW(0);
-	for (i = 0; i < 3; i++) {
+	for (i = 0; i < 3; i++)
 		phys_addr[i] = htons(read_eeprom(ioaddr, i));
-	}
 
 	dev = alloc_etherdev(sizeof (struct el3_private));
 	if (dev == NULL) {
@@ -668,7 +667,7 @@ static int __init el3_eisa_probe (struct device *device)
 {
 	short i;
 	int ioaddr, irq, if_port;
-	u16 phys_addr[3];
+	__be16 phys_addr[3];
 	struct net_device *dev = NULL;
 	struct eisa_device *edev;
 	int err;

drivers/net/3c515.c

@@ -572,12 +572,16 @@ static int corkscrew_setup(struct net_device *dev, int ioaddr,
 	int irq;
 	DECLARE_MAC_BUF(mac);
 
+#ifdef __ISAPNP__
 	if (idev) {
 		irq = pnp_irq(idev, 0);
 		vp->dev = &idev->dev;
 	} else {
 		irq = inw(ioaddr + 0x2002) & 15;
 	}
+#else
+	irq = inw(ioaddr + 0x2002) & 15;
+#endif
 
 	dev->base_addr = ioaddr;
 	dev->irq = irq;

drivers/net/Kconfig

@@ -2410,6 +2410,7 @@ config CHELSIO_T3
 	tristate "Chelsio Communications T3 10Gb Ethernet support"
 	depends on PCI
 	select FW_LOADER
+	select INET_LRO
 	help
 	  This driver supports Chelsio T3-based gigabit and 10Gb Ethernet
 	  adapters.

drivers/net/atlx/atl1.c

@@ -1876,7 +1876,8 @@ static u16 atl1_alloc_rx_buffers(struct atl1_adapter *adapter)
 
 		rfd_desc = ATL1_RFD_DESC(rfd_ring, rfd_next_to_use);
 
-		skb = dev_alloc_skb(adapter->rx_buffer_len + NET_IP_ALIGN);
+		skb = netdev_alloc_skb(adapter->netdev,
+				       adapter->rx_buffer_len + NET_IP_ALIGN);
 		if (unlikely(!skb)) {
 			/* Better luck next round */
 			adapter->net_stats.rx_dropped++;
@@ -2135,7 +2136,7 @@ static int atl1_tso(struct atl1_adapter *adapter, struct sk_buff *skb,
 				return -1;
 		}
 
-		if (skb->protocol == ntohs(ETH_P_IP)) {
+		if (skb->protocol == htons(ETH_P_IP)) {
 			struct iphdr *iph = ip_hdr(skb);
 
 			real_len = (((unsigned char *)iph - skb->data) +

drivers/net/bonding/bond_sysfs.c

@@ -50,6 +50,7 @@ extern struct bond_parm_tbl bond_mode_tbl[];
 extern struct bond_parm_tbl bond_lacp_tbl[];
 extern struct bond_parm_tbl xmit_hashtype_tbl[];
 extern struct bond_parm_tbl arp_validate_tbl[];
+extern struct bond_parm_tbl fail_over_mac_tbl[];
 
 static int expected_refcount = -1;
 static struct class *netdev_class;
@@ -111,7 +112,6 @@ static ssize_t bonding_store_bonds(struct class *cls, const char *buffer, size_t
 	char *ifname;
 	int rv, res = count;
 	struct bonding *bond;
-	struct bonding *nxt;
 
 	sscanf(buffer, "%16s", command); /* IFNAMSIZ*/
 	ifname = command + 1;
@@ -122,7 +122,7 @@ static ssize_t bonding_store_bonds(struct class *cls, const char *buffer, size_t
 	if (command[0] == '+') {
 		printk(KERN_INFO DRV_NAME
 			": %s is being created...\n", ifname);
-		rv = bond_create(ifname, &bonding_defaults, &bond);
+		rv = bond_create(ifname, &bonding_defaults);
 		if (rv) {
 			printk(KERN_INFO DRV_NAME ": Bond creation failed.\n");
 			res = rv;
@@ -134,7 +134,7 @@ static ssize_t bonding_store_bonds(struct class *cls, const char *buffer, size_t
 		rtnl_lock();
 		down_write(&bonding_rwsem);
 
-		list_for_each_entry_safe(bond, nxt, &bond_dev_list, bond_list)
+		list_for_each_entry(bond, &bond_dev_list, bond_list)
 			if (strnicmp(bond->dev->name, ifname, IFNAMSIZ) == 0) {
 				/* check the ref count on the bond's kobject.
 				 * If it's > expected, then there's a file open,
@@ -548,42 +548,37 @@ static ssize_t bonding_show_fail_over_mac(struct device *d, struct device_attrib
 {
 	struct bonding *bond = to_bond(d);
 
-	return sprintf(buf, "%d\n", bond->params.fail_over_mac) + 1;
+	return sprintf(buf, "%s %d\n",
+		       fail_over_mac_tbl[bond->params.fail_over_mac].modename,
+		       bond->params.fail_over_mac);
 }
 
 static ssize_t bonding_store_fail_over_mac(struct device *d, struct device_attribute *attr, const char *buf, size_t count)
 {
 	int new_value;
-	int ret = count;
 	struct bonding *bond = to_bond(d);
 
 	if (bond->slave_cnt != 0) {
 		printk(KERN_ERR DRV_NAME
 		       ": %s: Can't alter fail_over_mac with slaves in bond.\n",
 		       bond->dev->name);
-		ret = -EPERM;
-		goto out;
+		return -EPERM;
 	}
 
-	if (sscanf(buf, "%d", &new_value) != 1) {
+	new_value = bond_parse_parm(buf, fail_over_mac_tbl);
+	if (new_value < 0) {
 		printk(KERN_ERR DRV_NAME
-		       ": %s: no fail_over_mac value specified.\n",
-		       bond->dev->name);
-		ret = -EINVAL;
-		goto out;
+		       ": %s: Ignoring invalid fail_over_mac value %s.\n",
+		       bond->dev->name, buf);
+		return -EINVAL;
 	}
 
-	if ((new_value == 0) || (new_value == 1)) {
 	bond->params.fail_over_mac = new_value;
-		printk(KERN_INFO DRV_NAME ": %s: Setting fail_over_mac to %d.\n",
-		       bond->dev->name, new_value);
-	} else {
-		printk(KERN_INFO DRV_NAME
-		       ": %s: Ignoring invalid fail_over_mac value %d.\n",
-		       bond->dev->name, new_value);
-	}
-out:
-	return ret;
+	printk(KERN_INFO DRV_NAME ": %s: Setting fail_over_mac to %s (%d).\n",
+	       bond->dev->name, fail_over_mac_tbl[new_value].modename,
+	       new_value);
+
+	return count;
 }
 
 static DEVICE_ATTR(fail_over_mac, S_IRUGO | S_IWUSR, bonding_show_fail_over_mac, bonding_store_fail_over_mac);
@@ -951,6 +946,45 @@ static ssize_t bonding_store_lacp(struct device *d,
 }
 static DEVICE_ATTR(lacp_rate, S_IRUGO | S_IWUSR, bonding_show_lacp, bonding_store_lacp);
 
+/*
+ * Show and set the number of grat ARP to send after a failover event.
+ */
+static ssize_t bonding_show_n_grat_arp(struct device *d,
+				   struct device_attribute *attr,
+				   char *buf)
+{
+	struct bonding *bond = to_bond(d);
+
+	return sprintf(buf, "%d\n", bond->params.num_grat_arp);
+}
+
+static ssize_t bonding_store_n_grat_arp(struct device *d,
+				    struct device_attribute *attr,
+				    const char *buf, size_t count)
+{
+	int new_value, ret = count;
+	struct bonding *bond = to_bond(d);
+
+	if (sscanf(buf, "%d", &new_value) != 1) {
+		printk(KERN_ERR DRV_NAME
+		       ": %s: no num_grat_arp value specified.\n",
+		       bond->dev->name);
+		ret = -EINVAL;
+		goto out;
+	}
+	if (new_value < 0 || new_value > 255) {
+		printk(KERN_ERR DRV_NAME
+		       ": %s: Invalid num_grat_arp value %d not in range 0-255; rejected.\n",
+		       bond->dev->name, new_value);
+		ret = -EINVAL;
+		goto out;
+	} else {
+		bond->params.num_grat_arp = new_value;
+	}
+out:
+	return ret;
+}
+static DEVICE_ATTR(num_grat_arp, S_IRUGO | S_IWUSR, bonding_show_n_grat_arp, bonding_store_n_grat_arp);
 /*
  * Show and set the MII monitor interval.  There are two tricky bits
  * here.  First, if MII monitoring is activated, then we must disable
@@ -1388,6 +1422,7 @@ static struct attribute *per_bond_attrs[] = {
 	&dev_attr_updelay.attr,
 	&dev_attr_lacp_rate.attr,
 	&dev_attr_xmit_hash_policy.attr,
+	&dev_attr_num_grat_arp.attr,
 	&dev_attr_miimon.attr,
 	&dev_attr_primary.attr,
 	&dev_attr_use_carrier.attr,

drivers/net/bonding/bonding.h

@@ -125,6 +125,7 @@ struct bond_params {
 	int mode;
 	int xmit_policy;
 	int miimon;
+	int num_grat_arp;
 	int arp_interval;
 	int arp_validate;
 	int use_carrier;
@@ -157,6 +158,7 @@ struct slave {
 	unsigned long jiffies;
 	unsigned long last_arp_rx;
 	s8     link;    /* one of BOND_LINK_XXXX */
+	s8     new_link;
 	s8     state;   /* one of BOND_STATE_XXXX */
 	u32    original_flags;
 	u32    original_mtu;
@@ -168,6 +170,11 @@ struct slave {
 	struct tlb_slave_info tlb_info;
 };
 
+/*
+ * Link pseudo-state only used internally by monitors
+ */
+#define BOND_LINK_NOCHANGE -1
+
 /*
  * Here are the locking policies for the two bonding locks:
  *
@@ -241,6 +248,10 @@ static inline struct bonding *bond_get_bond_by_slave(struct slave *slave)
 	return (struct bonding *)slave->dev->master->priv;
 }
 
+#define BOND_FOM_NONE			0
+#define BOND_FOM_ACTIVE			1
+#define BOND_FOM_FOLLOW			2
+
 #define BOND_ARP_VALIDATE_NONE		0
 #define BOND_ARP_VALIDATE_ACTIVE	(1 << BOND_STATE_ACTIVE)
 #define BOND_ARP_VALIDATE_BACKUP	(1 << BOND_STATE_BACKUP)
@@ -301,7 +312,7 @@ static inline void bond_unset_master_alb_flags(struct bonding *bond)
 
 struct vlan_entry *bond_next_vlan(struct bonding *bond, struct vlan_entry *curr);
 int bond_dev_queue_xmit(struct bonding *bond, struct sk_buff *skb, struct net_device *slave_dev);
-int bond_create(char *name, struct bond_params *params, struct bonding **newbond);
+int bond_create(char *name, struct bond_params *params);
 void bond_destroy(struct bonding *bond);
 int  bond_release_and_destroy(struct net_device *bond_dev, struct net_device *slave_dev);
 int bond_create_sysfs(void);

drivers/net/cxgb3/adapter.h

@@ -42,6 +42,7 @@
 #include <linux/cache.h>
 #include <linux/mutex.h>
 #include <linux/bitops.h>
+#include <linux/inet_lro.h>
 #include "t3cdev.h"
 #include <asm/io.h>
 
@@ -92,6 +93,7 @@ struct sge_fl {                     /* SGE per free-buffer list state */
 	unsigned int gen;           /* free list generation */
 	struct fl_pg_chunk pg_chunk;/* page chunk cache */
 	unsigned int use_pages;     /* whether FL uses pages or sk_buffs */
+	unsigned int order;	    /* order of page allocations */
 	struct rx_desc *desc;       /* address of HW Rx descriptor ring */
 	struct rx_sw_desc *sdesc;   /* address of SW Rx descriptor ring */
 	dma_addr_t   phys_addr;     /* physical address of HW ring start */
@@ -116,12 +118,15 @@ struct sge_rspq {		/* state for an SGE response queue */
 	unsigned int polling;	/* is the queue serviced through NAPI? */
 	unsigned int holdoff_tmr;	/* interrupt holdoff timer in 100ns */
 	unsigned int next_holdoff;	/* holdoff time for next interrupt */
+	unsigned int rx_recycle_buf; /* whether recycling occurred
+					within current sop-eop */
 	struct rsp_desc *desc;	/* address of HW response ring */
 	dma_addr_t phys_addr;	/* physical address of the ring */
 	unsigned int cntxt_id;	/* SGE context id for the response q */
 	spinlock_t lock;	/* guards response processing */
 	struct sk_buff *rx_head;	/* offload packet receive queue head */
 	struct sk_buff *rx_tail;	/* offload packet receive queue tail */
+	struct sk_buff *pg_skb; /* used to build frag list in napi handler */
 
 	unsigned long offload_pkts;
 	unsigned long offload_bundles;
@@ -169,16 +174,29 @@ enum {				/* per port SGE statistics */
 	SGE_PSTAT_TX_CSUM,	/* # of TX checksum offloads */
 	SGE_PSTAT_VLANEX,	/* # of VLAN tag extractions */
 	SGE_PSTAT_VLANINS,	/* # of VLAN tag insertions */
+	SGE_PSTAT_LRO_AGGR,	/* # of page chunks added to LRO sessions */
+	SGE_PSTAT_LRO_FLUSHED,	/* # of flushed LRO sessions */
+	SGE_PSTAT_LRO_NO_DESC,	/* # of overflown LRO sessions */
 
 	SGE_PSTAT_MAX		/* must be last */
 };
 
+#define T3_MAX_LRO_SES 8
+#define T3_MAX_LRO_MAX_PKTS 64
+
 struct sge_qset {		/* an SGE queue set */
 	struct adapter *adap;
 	struct napi_struct napi;
 	struct sge_rspq rspq;
 	struct sge_fl fl[SGE_RXQ_PER_SET];
 	struct sge_txq txq[SGE_TXQ_PER_SET];
+	struct net_lro_mgr lro_mgr;
+	struct net_lro_desc lro_desc[T3_MAX_LRO_SES];
+	struct skb_frag_struct *lro_frag_tbl;
+	int lro_nfrags;
+	int lro_enabled;
+	int lro_frag_len;
+	void *lro_va;
 	struct net_device *netdev;
 	unsigned long txq_stopped;	/* which Tx queues are stopped */
 	struct timer_list tx_reclaim_timer;	/* reclaims TX buffers */

drivers/net/cxgb3/common.h

@@ -351,6 +351,7 @@ struct tp_params {
 
 struct qset_params {		/* SGE queue set parameters */
 	unsigned int polling;	/* polling/interrupt service for rspq */
+	unsigned int lro;	/* large receive offload */
 	unsigned int coalesce_usecs;	/* irq coalescing timer */
 	unsigned int rspq_size;	/* # of entries in response queue */
 	unsigned int fl_size;	/* # of entries in regular free list */

drivers/net/cxgb3/cxgb3_ioctl.h

@@ -90,6 +90,7 @@ struct ch_qset_params {
 	int32_t fl_size[2];
 	int32_t intr_lat;
 	int32_t polling;
+	int32_t lro;
 	int32_t cong_thres;
 };
 

drivers/net/cxgb3/cxgb3_main.c

@@ -1212,6 +1212,9 @@ static char stats_strings[][ETH_GSTRING_LEN] = {
 	"VLANinsertions     ",
 	"TxCsumOffload      ",
 	"RxCsumGood         ",
+	"LroAggregated      ",
+	"LroFlushed         ",
+	"LroNoDesc          ",
 	"RxDrops            ",
 
 	"CheckTXEnToggled   ",
@@ -1340,6 +1343,9 @@ static void get_stats(struct net_device *dev, struct ethtool_stats *stats,
 	*data++ = collect_sge_port_stats(adapter, pi, SGE_PSTAT_VLANINS);
 	*data++ = collect_sge_port_stats(adapter, pi, SGE_PSTAT_TX_CSUM);
 	*data++ = collect_sge_port_stats(adapter, pi, SGE_PSTAT_RX_CSUM_GOOD);
+	*data++ = collect_sge_port_stats(adapter, pi, SGE_PSTAT_LRO_AGGR);
+	*data++ = collect_sge_port_stats(adapter, pi, SGE_PSTAT_LRO_FLUSHED);
+	*data++ = collect_sge_port_stats(adapter, pi, SGE_PSTAT_LRO_NO_DESC);
 	*data++ = s->rx_cong_drops;
 
 	*data++ = s->num_toggled;
@@ -1558,6 +1564,13 @@ static int set_rx_csum(struct net_device *dev, u32 data)
 	struct port_info *p = netdev_priv(dev);
 
 	p->rx_csum_offload = data;
+	if (!data) {
+		struct adapter *adap = p->adapter;
+		int i;
+
+		for (i = p->first_qset; i < p->first_qset + p->nqsets; i++)
+			adap->sge.qs[i].lro_enabled = 0;
+	}
 	return 0;
 }
 
@@ -1830,6 +1843,11 @@ static int cxgb_extension_ioctl(struct net_device *dev, void __user *useraddr)
 				}
 			}
 		}
+		if (t.lro >= 0) {
+			struct sge_qset *qs = &adapter->sge.qs[t.qset_idx];
+			q->lro = t.lro;
+			qs->lro_enabled = t.lro;
+		}
 		break;
 	}
 	case CHELSIO_GET_QSET_PARAMS:{
@@ -1849,6 +1867,7 @@ static int cxgb_extension_ioctl(struct net_device *dev, void __user *useraddr)
 		t.fl_size[0] = q->fl_size;
 		t.fl_size[1] = q->jumbo_size;
 		t.polling = q->polling;
+		t.lro = q->lro;
 		t.intr_lat = q->coalesce_usecs;
 		t.cong_thres = q->cong_thres;
 

drivers/net/cxgb3/t3_cpl.h

@@ -174,6 +174,13 @@ enum {				/* TCP congestion control algorithms */
 	CONG_ALG_HIGHSPEED
 };
 
+enum {			/* RSS hash type */
+	RSS_HASH_NONE = 0,
+	RSS_HASH_2_TUPLE = 1,
+	RSS_HASH_4_TUPLE = 2,
+	RSS_HASH_TCPV6 = 3
+};
+
 union opcode_tid {
 	__be32 opcode_tid;
 	__u8 opcode;
@@ -184,6 +191,10 @@ union opcode_tid {
 #define G_OPCODE(x) (((x) >> S_OPCODE) & 0xFF)
 #define G_TID(x)    ((x) & 0xFFFFFF)
 
+#define S_HASHTYPE 22
+#define M_HASHTYPE 0x3
+#define G_HASHTYPE(x) (((x) >> S_HASHTYPE) & M_HASHTYPE)
+
 /* tid is assumed to be 24-bits */
 #define MK_OPCODE_TID(opcode, tid) (V_OPCODE(opcode) | (tid))
 

drivers/net/dl2k.c

@@ -499,7 +499,7 @@ rio_timer (unsigned long data)
 			entry = np->old_rx % RX_RING_SIZE;
 			/* Dropped packets don't need to re-allocate */
 			if (np->rx_skbuff[entry] == NULL) {
-				skb = dev_alloc_skb (np->rx_buf_sz);
+				skb = netdev_alloc_skb (dev, np->rx_buf_sz);
 				if (skb == NULL) {
 					np->rx_ring[entry].fraginfo = 0;
 					printk (KERN_INFO
@@ -570,7 +570,7 @@ alloc_list (struct net_device *dev)
 	/* Allocate the rx buffers */
 	for (i = 0; i < RX_RING_SIZE; i++) {
 		/* Allocated fixed size of skbuff */
-		struct sk_buff *skb = dev_alloc_skb (np->rx_buf_sz);
+		struct sk_buff *skb = netdev_alloc_skb (dev, np->rx_buf_sz);
 		np->rx_skbuff[i] = skb;
 		if (skb == NULL) {
 			printk (KERN_ERR
@@ -867,7 +867,7 @@ receive_packet (struct net_device *dev)
 						  PCI_DMA_FROMDEVICE);
 				skb_put (skb = np->rx_skbuff[entry], pkt_len);
 				np->rx_skbuff[entry] = NULL;
-			} else if ((skb = dev_alloc_skb (pkt_len + 2)) != NULL) {
+			} else if ((skb = netdev_alloc_skb(dev, pkt_len + 2))) {
 				pci_dma_sync_single_for_cpu(np->pdev,
 							    desc_to_dma(desc),
 							    np->rx_buf_sz,
@@ -904,7 +904,7 @@ receive_packet (struct net_device *dev)
 		struct sk_buff *skb;
 		/* Dropped packets don't need to re-allocate */
 		if (np->rx_skbuff[entry] == NULL) {
-			skb = dev_alloc_skb (np->rx_buf_sz);
+			skb = netdev_alloc_skb(dev, np->rx_buf_sz);
 			if (skb == NULL) {
 				np->rx_ring[entry].fraginfo = 0;
 				printk (KERN_INFO

drivers/net/hamachi.c

@@ -1140,11 +1140,11 @@ static void hamachi_tx_timeout(struct net_device *dev)
 	}
 	/* Fill in the Rx buffers.  Handle allocation failure gracefully. */
 	for (i = 0; i < RX_RING_SIZE; i++) {
-		struct sk_buff *skb = dev_alloc_skb(hmp->rx_buf_sz);
+		struct sk_buff *skb = netdev_alloc_skb(dev, hmp->rx_buf_sz);
 		hmp->rx_skbuff[i] = skb;
 		if (skb == NULL)
 			break;
-		skb->dev = dev;         /* Mark as being used by this device. */
+
 		skb_reserve(skb, 2); /* 16 byte align the IP header. */
                 hmp->rx_ring[i].addr = cpu_to_leXX(pci_map_single(hmp->pci_dev,
 			skb->data, hmp->rx_buf_sz, PCI_DMA_FROMDEVICE));
@@ -1178,14 +1178,6 @@ static void hamachi_init_ring(struct net_device *dev)
 	hmp->cur_rx = hmp->cur_tx = 0;
 	hmp->dirty_rx = hmp->dirty_tx = 0;
 
-#if 0
-	/* This is wrong.  I'm not sure what the original plan was, but this
-	 * is wrong.  An MTU of 1 gets you a buffer of 1536, while an MTU
-	 * of 1501 gets a buffer of 1533? -KDU
-	 */
-	hmp->rx_buf_sz = (dev->mtu <= 1500 ? PKT_BUF_SZ : dev->mtu + 32);
-#endif
-	/* My attempt at a reasonable correction */
 	/* +26 gets the maximum ethernet encapsulation, +7 & ~7 because the
 	 * card needs room to do 8 byte alignment, +2 so we can reserve
 	 * the first 2 bytes, and +16 gets room for the status word from the

drivers/net/ixp2000/ixpdev.c

@@ -108,14 +108,14 @@ static int ixpdev_rx(struct net_device *dev, int processed, int budget)
 		if (unlikely(!netif_running(nds[desc->channel])))
 			goto err;
 
-		skb = dev_alloc_skb(desc->pkt_length + 2);
+		skb = netdev_alloc_skb(dev, desc->pkt_length + 2);
 		if (likely(skb != NULL)) {
 			skb_reserve(skb, 2);
 			skb_copy_to_linear_data(skb, buf, desc->pkt_length);
 			skb_put(skb, desc->pkt_length);
 			skb->protocol = eth_type_trans(skb, nds[desc->channel]);
 
-			skb->dev->last_rx = jiffies;
+			dev->last_rx = jiffies;
 
 			netif_receive_skb(skb);
 		}

drivers/net/phy/Kconfig

@@ -53,7 +53,8 @@ config SMSC_PHY
 config BROADCOM_PHY
 	tristate "Drivers for Broadcom PHYs"
 	---help---
-	  Currently supports the BCM5411, BCM5421 and BCM5461 PHYs.
+	  Currently supports the BCM5411, BCM5421, BCM5461, BCM5464, BCM5481
+	  and BCM5482 PHYs.
 
 config ICPLUS_PHY
 	tristate "Drivers for ICPlus PHYs"

drivers/net/phy/broadcom.c

@@ -24,6 +24,12 @@
 #define MII_BCM54XX_ESR		0x11	/* BCM54xx extended status register */
 #define MII_BCM54XX_ESR_IS	0x1000	/* Interrupt status */
 
+#define MII_BCM54XX_EXP_DATA	0x15	/* Expansion register data */
+#define MII_BCM54XX_EXP_SEL	0x17	/* Expansion register select */
+#define MII_BCM54XX_EXP_SEL_SSD	0x0e00	/* Secondary SerDes select */
+#define MII_BCM54XX_EXP_SEL_ER	0x0f00	/* Expansion register select */
+
+#define MII_BCM54XX_AUX_CTL	0x18	/* Auxiliary control register */
 #define MII_BCM54XX_ISR		0x1a	/* BCM54xx interrupt status register */
 #define MII_BCM54XX_IMR		0x1b	/* BCM54xx interrupt mask register */
 #define MII_BCM54XX_INT_CRCERR	0x0001	/* CRC error */
@@ -42,10 +48,120 @@
 #define MII_BCM54XX_INT_MDIX	0x2000	/* MDIX status change */
 #define MII_BCM54XX_INT_PSERR	0x4000	/* Pair swap error */
 
+#define MII_BCM54XX_SHD		0x1c	/* 0x1c shadow registers */
+#define MII_BCM54XX_SHD_WRITE	0x8000
+#define MII_BCM54XX_SHD_VAL(x)	((x & 0x1f) << 10)
+#define MII_BCM54XX_SHD_DATA(x)	((x & 0x3ff) << 0)
+
+/*
+ * Broadcom LED source encodings.  These are used in BCM5461, BCM5481,
+ * BCM5482, and possibly some others.
+ */
+#define BCM_LED_SRC_LINKSPD1	0x0
+#define BCM_LED_SRC_LINKSPD2	0x1
+#define BCM_LED_SRC_XMITLED	0x2
+#define BCM_LED_SRC_ACTIVITYLED	0x3
+#define BCM_LED_SRC_FDXLED	0x4
+#define BCM_LED_SRC_SLAVE	0x5
+#define BCM_LED_SRC_INTR	0x6
+#define BCM_LED_SRC_QUALITY	0x7
+#define BCM_LED_SRC_RCVLED	0x8
+#define BCM_LED_SRC_MULTICOLOR1	0xa
+#define BCM_LED_SRC_OPENSHORT	0xb
+#define BCM_LED_SRC_OFF		0xe	/* Tied high */
+#define BCM_LED_SRC_ON		0xf	/* Tied low */
+
+/*
+ * BCM5482: Shadow registers
+ * Shadow values go into bits [14:10] of register 0x1c to select a shadow
+ * register to access.
+ */
+#define BCM5482_SHD_LEDS1	0x0d	/* 01101: LED Selector 1 */
+					/* LED3 / ~LINKSPD[2] selector */
+#define BCM5482_SHD_LEDS1_LED3(src)	((src & 0xf) << 4)
+					/* LED1 / ~LINKSPD[1] selector */
+#define BCM5482_SHD_LEDS1_LED1(src)	((src & 0xf) << 0)
+#define BCM5482_SHD_SSD		0x14	/* 10100: Secondary SerDes control */
+#define BCM5482_SHD_SSD_LEDM	0x0008	/* SSD LED Mode enable */
+#define BCM5482_SHD_SSD_EN	0x0001	/* SSD enable */
+#define BCM5482_SHD_MODE	0x1f	/* 11111: Mode Control Register */
+#define BCM5482_SHD_MODE_1000BX	0x0001	/* Enable 1000BASE-X registers */
+
+/*
+ * BCM5482: Secondary SerDes registers
+ */
+#define BCM5482_SSD_1000BX_CTL		0x00	/* 1000BASE-X Control */
+#define BCM5482_SSD_1000BX_CTL_PWRDOWN	0x0800	/* Power-down SSD */
+#define BCM5482_SSD_SGMII_SLAVE		0x15	/* SGMII Slave Register */
+#define BCM5482_SSD_SGMII_SLAVE_EN	0x0002	/* Slave mode enable */
+#define BCM5482_SSD_SGMII_SLAVE_AD	0x0001	/* Slave auto-detection */
+
+/*
+ * Device flags for PHYs that can be configured for different operating
+ * modes.
+ */
+#define PHY_BCM_FLAGS_VALID		0x80000000
+#define PHY_BCM_FLAGS_INTF_XAUI		0x00000020
+#define PHY_BCM_FLAGS_INTF_SGMII	0x00000010
+#define PHY_BCM_FLAGS_MODE_1000BX	0x00000002
+#define PHY_BCM_FLAGS_MODE_COPPER	0x00000001
+
 MODULE_DESCRIPTION("Broadcom PHY driver");
 MODULE_AUTHOR("Maciej W. Rozycki");
 MODULE_LICENSE("GPL");
 
+/*
+ * Indirect register access functions for the 1000BASE-T/100BASE-TX/10BASE-T
+ * 0x1c shadow registers.
+ */
+static int bcm54xx_shadow_read(struct phy_device *phydev, u16 shadow)
+{
+	phy_write(phydev, MII_BCM54XX_SHD, MII_BCM54XX_SHD_VAL(shadow));
+	return MII_BCM54XX_SHD_DATA(phy_read(phydev, MII_BCM54XX_SHD));
+}
+
+static int bcm54xx_shadow_write(struct phy_device *phydev, u16 shadow, u16 val)
+{
+	return phy_write(phydev, MII_BCM54XX_SHD,
+			 MII_BCM54XX_SHD_WRITE |
+			 MII_BCM54XX_SHD_VAL(shadow) |
+			 MII_BCM54XX_SHD_DATA(val));
+}
+
+/*
+ * Indirect register access functions for the Expansion Registers
+ * and Secondary SerDes registers (when sec_serdes=1).
+ */
+static int bcm54xx_exp_read(struct phy_device *phydev,
+			    int sec_serdes, u8 regnum)
+{
+	int val;
+
+	phy_write(phydev, MII_BCM54XX_EXP_SEL,
+		  (sec_serdes ? MII_BCM54XX_EXP_SEL_SSD :
+				MII_BCM54XX_EXP_SEL_ER) |
+		  regnum);
+	val = phy_read(phydev, MII_BCM54XX_EXP_DATA);
+	phy_write(phydev, MII_BCM54XX_EXP_SEL, regnum);
+
+	return val;
+}
+
+static int bcm54xx_exp_write(struct phy_device *phydev,
+			     int sec_serdes, u8 regnum, u16 val)
+{
+	int ret;
+
+	phy_write(phydev, MII_BCM54XX_EXP_SEL,
+		  (sec_serdes ? MII_BCM54XX_EXP_SEL_SSD :
+				MII_BCM54XX_EXP_SEL_ER) |
+		  regnum);
+	ret = phy_write(phydev, MII_BCM54XX_EXP_DATA, val);
+	phy_write(phydev, MII_BCM54XX_EXP_SEL, regnum);
+
+	return ret;
+}
+
 static int bcm54xx_config_init(struct phy_device *phydev)
 {
 	int reg, err;
@@ -70,6 +186,87 @@ static int bcm54xx_config_init(struct phy_device *phydev)
 	return 0;
 }
 
+static int bcm5482_config_init(struct phy_device *phydev)
+{
+	int err, reg;
+
+	err = bcm54xx_config_init(phydev);
+
+	if (phydev->dev_flags & PHY_BCM_FLAGS_MODE_1000BX) {
+		/*
+		 * Enable secondary SerDes and its use as an LED source
+		 */
+		reg = bcm54xx_shadow_read(phydev, BCM5482_SHD_SSD);
+		bcm54xx_shadow_write(phydev, BCM5482_SHD_SSD,
+				     reg |
+				     BCM5482_SHD_SSD_LEDM |
+				     BCM5482_SHD_SSD_EN);
+
+		/*
+		 * Enable SGMII slave mode and auto-detection
+		 */
+		reg = bcm54xx_exp_read(phydev, 1, BCM5482_SSD_SGMII_SLAVE);
+		bcm54xx_exp_write(phydev, 1, BCM5482_SSD_SGMII_SLAVE,
+				  reg |
+				  BCM5482_SSD_SGMII_SLAVE_EN |
+				  BCM5482_SSD_SGMII_SLAVE_AD);
+
+		/*
+		 * Disable secondary SerDes powerdown
+		 */
+		reg = bcm54xx_exp_read(phydev, 1, BCM5482_SSD_1000BX_CTL);
+		bcm54xx_exp_write(phydev, 1, BCM5482_SSD_1000BX_CTL,
+				  reg & ~BCM5482_SSD_1000BX_CTL_PWRDOWN);
+
+		/*
+		 * Select 1000BASE-X register set (primary SerDes)
+		 */
+		reg = bcm54xx_shadow_read(phydev, BCM5482_SHD_MODE);
+		bcm54xx_shadow_write(phydev, BCM5482_SHD_MODE,
+				     reg | BCM5482_SHD_MODE_1000BX);
+
+		/*
+		 * LED1=ACTIVITYLED, LED3=LINKSPD[2]
+		 * (Use LED1 as secondary SerDes ACTIVITY LED)
+		 */
+		bcm54xx_shadow_write(phydev, BCM5482_SHD_LEDS1,
+			BCM5482_SHD_LEDS1_LED1(BCM_LED_SRC_ACTIVITYLED) |
+			BCM5482_SHD_LEDS1_LED3(BCM_LED_SRC_LINKSPD2));
+
+		/*
+		 * Auto-negotiation doesn't seem to work quite right
+		 * in this mode, so we disable it and force it to the
+		 * right speed/duplex setting.  Only 'link status'
+		 * is important.
+		 */
+		phydev->autoneg = AUTONEG_DISABLE;
+		phydev->speed = SPEED_1000;
+		phydev->duplex = DUPLEX_FULL;
+	}
+
+	return err;
+}
+
+static int bcm5482_read_status(struct phy_device *phydev)
+{
+	int err;
+
+	err = genphy_read_status(phydev);
+
+	if (phydev->dev_flags & PHY_BCM_FLAGS_MODE_1000BX) {
+		/*
+		 * Only link status matters for 1000Base-X mode, so force
+		 * 1000 Mbit/s full-duplex status
+		 */
+		if (phydev->link) {
+			phydev->speed = SPEED_1000;
+			phydev->duplex = DUPLEX_FULL;
+		}
+	}
+
+	return err;
+}
+
 static int bcm54xx_ack_interrupt(struct phy_device *phydev)
 {
 	int reg;
@@ -210,9 +407,9 @@ static struct phy_driver bcm5482_driver = {
 	.name		= "Broadcom BCM5482",
 	.features	= PHY_GBIT_FEATURES,
 	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
-	.config_init	= bcm54xx_config_init,
+	.config_init	= bcm5482_config_init,
 	.config_aneg	= genphy_config_aneg,
-	.read_status	= genphy_read_status,
+	.read_status	= bcm5482_read_status,
 	.ack_interrupt	= bcm54xx_ack_interrupt,
 	.config_intr	= bcm54xx_config_intr,
 	.driver 	= { .owner = THIS_MODULE },

drivers/net/tg3.c

@@ -2013,7 +2013,7 @@ static int tg3_set_power_state(struct tg3 *tp, pci_power_t state)
 		       "requested.\n",
 		       tp->dev->name, state);
 		return -EINVAL;
-	};
+	}
 
 	power_control |= PCI_PM_CTRL_PME_ENABLE;
 
@@ -2272,7 +2272,7 @@ static void tg3_aux_stat_to_speed_duplex(struct tg3 *tp, u32 val, u16 *speed, u8
 		*speed = SPEED_INVALID;
 		*duplex = DUPLEX_INVALID;
 		break;
-	};
+	}
 }
 
 static void tg3_phy_copper_begin(struct tg3 *tp)
@@ -2384,7 +2384,7 @@ static void tg3_phy_copper_begin(struct tg3 *tp)
 		case SPEED_1000:
 			bmcr |= TG3_BMCR_SPEED1000;
 			break;
-		};
+		}
 
 		if (tp->link_config.duplex == DUPLEX_FULL)
 			bmcr |= BMCR_FULLDPLX;
@@ -3082,7 +3082,7 @@ static int tg3_fiber_aneg_smachine(struct tg3 *tp,
 	default:
 		ret = ANEG_FAILED;
 		break;
-	};
+	}
 
 	return ret;
 }
@@ -3924,7 +3924,7 @@ static int tg3_alloc_rx_skb(struct tg3 *tp, u32 opaque_key,
 
 	default:
 		return -EINVAL;
-	};
+	}
 
 	/* Do not overwrite any of the map or rp information
 	 * until we are sure we can commit to a new buffer.
@@ -3984,7 +3984,7 @@ static void tg3_recycle_rx(struct tg3 *tp, u32 opaque_key,
 
 	default:
 		return;
-	};
+	}
 
 	dest_map->skb = src_map->skb;
 	pci_unmap_addr_set(dest_map, mapping,
@@ -5347,7 +5347,7 @@ static int tg3_stop_block(struct tg3 *tp, unsigned long ofs, u32 enable_bit, int
 
 		default:
 			break;
-		};
+		}
 	}
 
 	val = tr32(ofs);
@@ -5589,7 +5589,7 @@ static void tg3_write_sig_pre_reset(struct tg3 *tp, int kind)
 
 		default:
 			break;
-		};
+		}
 	}
 
 	if (kind == RESET_KIND_INIT ||
@@ -5614,7 +5614,7 @@ static void tg3_write_sig_post_reset(struct tg3 *tp, int kind)
 
 		default:
 			break;
-		};
+		}
 	}
 
 	if (kind == RESET_KIND_SHUTDOWN)
@@ -5643,7 +5643,7 @@ static void tg3_write_sig_legacy(struct tg3 *tp, int kind)
 
 		default:
 			break;
-		};
+		}
 	}
 }
 
@@ -7677,7 +7677,7 @@ static int tg3_reset_hw(struct tg3 *tp, int reset_phy)
 
 	default:
 		break;
-	};
+	}
 
 	if (tp->tg3_flags3 & TG3_FLG3_ENABLE_APE)
 		/* Write our heartbeat update interval to APE. */
@@ -11379,7 +11379,7 @@ static void __devinit tg3_get_eeprom_hw_cfg(struct tg3 *tp)
 						 LED_CTRL_MODE_PHY_2);
 			break;
 
-		};
+		}
 
 		if ((GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5700 ||
 		     GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5701) &&
@@ -12690,7 +12690,7 @@ static u32 __devinit tg3_calc_dma_bndry(struct tg3 *tp, u32 val)
 			val |= (DMA_RWCTRL_READ_BNDRY_384_PCIX |
 				DMA_RWCTRL_WRITE_BNDRY_384_PCIX);
 			break;
-		};
+		}
 	} else if (tp->tg3_flags2 & TG3_FLG2_PCI_EXPRESS) {
 		switch (cacheline_size) {
 		case 16:
@@ -12707,7 +12707,7 @@ static u32 __devinit tg3_calc_dma_bndry(struct tg3 *tp, u32 val)
 			val &= ~DMA_RWCTRL_WRITE_BNDRY_DISAB_PCIE;
 			val |= DMA_RWCTRL_WRITE_BNDRY_128_PCIE;
 			break;
-		};
+		}
 	} else {
 		switch (cacheline_size) {
 		case 16:
@@ -12751,7 +12751,7 @@ static u32 __devinit tg3_calc_dma_bndry(struct tg3 *tp, u32 val)
 			val |= (DMA_RWCTRL_READ_BNDRY_1024 |
 				DMA_RWCTRL_WRITE_BNDRY_1024);
 			break;
-		};
+		}
 	}
 
 out:
@@ -13111,7 +13111,7 @@ static char * __devinit tg3_phy_string(struct tg3 *tp)
 	case PHY_ID_BCM8002:	return "8002/serdes";
 	case 0:			return "serdes";
 	default:		return "unknown";
-	};
+	}
 }
 
 static char * __devinit tg3_bus_string(struct tg3 *tp, char *str)

drivers/net/usb/catc.c

@@ -423,7 +423,10 @@ static int catc_hard_start_xmit(struct sk_buff *skb, struct net_device *netdev)
 
 	catc->tx_ptr = (((catc->tx_ptr - 1) >> 6) + 1) << 6;
 	tx_buf = catc->tx_buf[catc->tx_idx] + catc->tx_ptr;
-	*((u16*)tx_buf) = (catc->is_f5u011) ? cpu_to_be16((u16)skb->len) : cpu_to_le16((u16)skb->len);
+	if (catc->is_f5u011)
+		*(__be16 *)tx_buf = cpu_to_be16(skb->len);
+	else
+		*(__le16 *)tx_buf = cpu_to_le16(skb->len);
 	skb_copy_from_linear_data(skb, tx_buf + 2, skb->len);
 	catc->tx_ptr += skb->len + 2;
 

drivers/net/usb/rndis_host.c

@@ -283,8 +283,8 @@ generic_rndis_bind(struct usbnet *dev, struct usb_interface *intf, int flags)
 		struct rndis_set_c	*set_c;
 		struct rndis_halt	*halt;
 	} u;
-	u32			tmp, phym_unspec;
-	__le32			*phym;
+	u32			tmp;
+	__le32			phym_unspec, *phym;
 	int			reply_len;
 	unsigned char		*bp;
 

drivers/net/via-velocity.c

@@ -1495,24 +1495,18 @@ static inline void velocity_rx_csum(struct rx_desc *rd, struct sk_buff *skb)
  *	enough. This function returns a negative value if the received
  *	packet is too big or if memory is exhausted.
  */
-static inline int velocity_rx_copy(struct sk_buff **rx_skb, int pkt_size,
+static int velocity_rx_copy(struct sk_buff **rx_skb, int pkt_size,
 			    struct velocity_info *vptr)
 {
 	int ret = -1;
-
 	if (pkt_size < rx_copybreak) {
 		struct sk_buff *new_skb;
 
-		new_skb = dev_alloc_skb(pkt_size + 2);
+		new_skb = netdev_alloc_skb(vptr->dev, pkt_size + 2);
 		if (new_skb) {
-			new_skb->dev = vptr->dev;
 			new_skb->ip_summed = rx_skb[0]->ip_summed;
-
-			if (vptr->flags & VELOCITY_FLAGS_IP_ALIGN)
 			skb_reserve(new_skb, 2);
-
-			skb_copy_from_linear_data(rx_skb[0], new_skb->data,
-						  pkt_size);
+			skb_copy_from_linear_data(*rx_skb, new_skb->data, pkt_size);
 			*rx_skb = new_skb;
 			ret = 0;
 		}
@@ -1533,12 +1527,8 @@ static inline int velocity_rx_copy(struct sk_buff **rx_skb, int pkt_size,
 static inline void velocity_iph_realign(struct velocity_info *vptr,
 					struct sk_buff *skb, int pkt_size)
 {
-	/* FIXME - memmove ? */
 	if (vptr->flags & VELOCITY_FLAGS_IP_ALIGN) {
-		int i;
-
-		for (i = pkt_size; i >= 0; i--)
-			*(skb->data + i + 2) = *(skb->data + i);
+		memmove(skb->data + 2, skb->data, pkt_size);
 		skb_reserve(skb, 2);
 	}
 }
@@ -1629,7 +1619,7 @@ static int velocity_alloc_rx_buf(struct velocity_info *vptr, int idx)
 	struct rx_desc *rd = &(vptr->rd_ring[idx]);
 	struct velocity_rd_info *rd_info = &(vptr->rd_info[idx]);
 
-	rd_info->skb = dev_alloc_skb(vptr->rx_buf_sz + 64);
+	rd_info->skb = netdev_alloc_skb(vptr->dev, vptr->rx_buf_sz + 64);
 	if (rd_info->skb == NULL)
 		return -ENOMEM;
 
@@ -1638,7 +1628,6 @@ static int velocity_alloc_rx_buf(struct velocity_info *vptr, int idx)
 	 *	64byte alignment.
 	 */
 	skb_reserve(rd_info->skb, (unsigned long) rd_info->skb->data & 63);
-	rd_info->skb->dev = vptr->dev;
 	rd_info->skb_dma = pci_map_single(vptr->pdev, rd_info->skb->data, vptr->rx_buf_sz, PCI_DMA_FROMDEVICE);
 
 	/*

drivers/net/wireless/zd1211rw/zd_mac.c

@@ -807,7 +807,7 @@ void zd_process_intr(struct work_struct *work)
 	u16 int_status;
 	struct zd_mac *mac = container_of(work, struct zd_mac, process_intr);
 
-	int_status = le16_to_cpu(*(u16 *)(mac->intr_buffer+4));
+	int_status = le16_to_cpu(*(__le16 *)(mac->intr_buffer+4));
 	if (int_status & INT_CFG_NEXT_BCN) {
 		if (net_ratelimit())
 			dev_dbg_f(zd_mac_dev(mac), "INT_CFG_NEXT_BCN\n");

drivers/net/wireless/zd1211rw/zd_usb.c

@@ -342,7 +342,7 @@ static inline void handle_regs_int(struct urb *urb)
 	ZD_ASSERT(in_interrupt());
 	spin_lock(&intr->lock);
 
-	int_num = le16_to_cpu(*(u16 *)(urb->transfer_buffer+2));
+	int_num = le16_to_cpu(*(__le16 *)(urb->transfer_buffer+2));
 	if (int_num == CR_INTERRUPT) {
 		struct zd_mac *mac = zd_hw_mac(zd_usb_to_hw(urb->context));
 		memcpy(&mac->intr_buffer, urb->transfer_buffer,