Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC platform changes from Olof Johansson:
 "New and updated SoC support.  Among the things new for this release
  are:

   - More support for the AM33xx platforms from TI
   - Tegra 124 support, and some updates to older tegra families as well
   - imx cleanups and updates across the board
   - A rename of Broadcom's Mobile platforms which were introduced as
     ARCH_BCM, and turned out to be too broad a name.  New name is
     ARCH_BCM_MOBILE.
   - A whole bunch of updates and fixes for integrator, making the
     platform code more modern and switches over to DT-only booting.
   - Support for two new Renesas shmobile chipsets.  Next up for them is
     more work on consolidation instead of introduction of new
     non-multiplatform SoCs, we're all looking forward to that!
   - Misc cleanups for older Samsung platforms, some Allwinner updates,
     etc"

* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (159 commits)
  ARM: bcm281xx: Add ARCH_BCM_MOBILE to bcm config
  ARM: bcm_defconfig: Run "make savedefconfig"
  ARM: bcm281xx: Add ARCH Timers to config
  rename ARCH_BCM to ARCH_BCM_MOBILE (mach-bcm)
  ARM: vexpress: Enable platform-specific options in defconfig
  ARM: vexpress: Make defconfig work again
  ARM: sunxi: remove .init_time hooks
  ARM: imx: enable suspend for imx6sl
  ARM: imx: ensure dsm_request signal is not asserted when setting LPM
  ARM: imx6q: call WB and RBC configuration from imx6q_pm_enter()
  ARM: imx6q: move low-power code out of clock driver
  ARM: imx: drop extern with function prototypes in common.h
  ARM: imx: reset core along with enable/disable operation
  ARM: imx: do not return from imx_cpu_die() call
  ARM: imx_v6_v7_defconfig: Select CONFIG_PROVE_LOCKING
  ARM: imx_v6_v7_defconfig: Enable LEDS_GPIO related options
  ARM: mxs_defconfig: Turn off CONFIG_DEBUG_GPIO
  ARM: imx: replace imx6q_restart() with mxc_restart()
  ARM: mach-imx: mm-imx5: Retrieve iomuxc base address from dt
  ARM: mach-imx: mm-imx5: Retrieve tzic base address from dt
  ...

Documentation/arm/Marvell/README

@@ -88,6 +88,7 @@ EBU Armada family
         MV78230
         MV78260
         MV78460
+    NOTE: not to be confused with the non-SMP 78xx0 SoCs
 
   Product Brief: http://www.marvell.com/embedded-processors/armada-xp/assets/Marvell-ArmadaXP-SoC-product%20brief.pdf
   No public datasheet available.

Documentation/arm/sunxi/README

@@ -10,6 +10,10 @@ SunXi family
   Linux kernel mach directory: arch/arm/mach-sunxi
 
   Flavors:
+    * ARM926 based SoCs
+      - Allwinner F20 (sun3i)
+        + Not Supported
+
     * ARM Cortex-A8 based SoCs
       - Allwinner A10 (sun4i)
         + Datasheet
@@ -25,4 +29,24 @@ SunXi family
         + Datasheet
 	  http://dl.linux-sunxi.org/A13/A13%20Datasheet%20-%20v1.12%20%282012-03-29%29.pdf
         + User Manual
-	  http://dl.linux-sunxi.org/A13/A13%20User%20Manual%20-%20v1.2%20%282013-08-08%29.pdf
+          http://dl.linux-sunxi.org/A13/A13%20User%20Manual%20-%20v1.2%20%282013-01-08%29.pdf
+
+    * Dual ARM Cortex-A7 based SoCs
+      - Allwinner A20 (sun7i)
+        + User Manual
+          http://dl.linux-sunxi.org/A20/A20%20User%20Manual%202013-03-22.pdf
+
+      - Allwinner A23
+        + Not Supported
+
+    * Quad ARM Cortex-A7 based SoCs
+      - Allwinner A31 (sun6i)
+        + Datasheet
+          http://dl.linux-sunxi.org/A31/A31%20Datasheet%20-%20v1.00%20(2012-12-24).pdf
+
+      - Allwinner A31s (sun6i)
+        + Not Supported
+
+    * Quad ARM Cortex-A15, Quad ARM Cortex-A7 based SoCs
+      - Allwinner A80
+        + Not Supported
\ No newline at end of file

Documentation/devicetree/bindings/arm/arm-boards

@@ -9,9 +9,53 @@ Required properties (in root node):
 
 FPGA type interrupt controllers, see the versatile-fpga-irq binding doc.
 
-In the root node the Integrator/CP must have a /cpcon node pointing
-to the CP control registers, and the Integrator/AP must have a
-/syscon node pointing to the Integrator/AP system controller.
+Required nodes:
+
+- core-module: the root node to the Integrator platforms must have
+  a core-module with regs and the compatible string
+  "arm,core-module-integrator"
+
+  Required properties for the core module:
+  - regs: the location and size of the core module registers, one
+    range of 0x200 bytes.
+
+- syscon: the root node of the Integrator platforms must have a
+  system controller node pointong to the control registers,
+  with the compatible string
+  "arm,integrator-ap-syscon"
+  "arm,integrator-cp-syscon"
+  respectively.
+
+  Required properties for the system controller:
+  - regs: the location and size of the system controller registers,
+    one range of 0x100 bytes.
+
+  Required properties for the AP system controller:
+  - interrupts: the AP syscon node must include the logical module
+    interrupts, stated in order of module instance <module 0>,
+    <module 1>, <module 2> ... for the CP system controller this
+    is not required not of any use.
+
+/dts-v1/;
+/include/ "integrator.dtsi"
+
+/ {
+	model = "ARM Integrator/AP";
+	compatible = "arm,integrator-ap";
+
+	core-module@10000000 {
+		compatible = "arm,core-module-integrator";
+		reg = <0x10000000 0x200>;
+	};
+
+	syscon {
+		compatible = "arm,integrator-ap-syscon";
+		reg = <0x11000000 0x100>;
+		interrupt-parent = <&pic>;
+		/* These are the logic module IRQs */
+		interrupts = <9>, <10>, <11>, <12>;
+	};
+};
 
 
 ARM Versatile Application and Platform Baseboards

Documentation/devicetree/bindings/clock/imx6q-clock.txt

@@ -215,6 +215,11 @@ clocks and IDs.
 	cko2      		200
 	cko      		201
 	vdoa      		202
+	pll4_audio_div		203
+	lvds1_sel		204
+	lvds2_sel		205
+	lvds1_gate		206
+	lvds2_gate		207
 
 Examples:
 

Documentation/devicetree/bindings/clock/sunxi.txt

@@ -45,8 +45,8 @@ Additionally, "allwinner,*-gates-clk" clocks require:
 
 Clock consumers should specify the desired clocks they use with a
 "clocks" phandle cell. Consumers that are using a gated clock should
-provide an additional ID in their clock property. The values of this
-ID are documented in sunxi/<soc>-gates.txt.
+provide an additional ID in their clock property. This ID is the
+offset of the bit controlling this particular gate in the register.
 
 For example:
 

Documentation/devicetree/bindings/clock/sunxi/sun4i-a10-gates.txt

-Gate clock outputs
-------------------
-
-  * AXI gates ("allwinner,sun4i-axi-gates-clk")
-
-    DRAM					0
-
-  * AHB gates ("allwinner,sun4i-ahb-gates-clk")
-
-    USB0					0
-    EHCI0					1
-    OHCI0					2*
-    EHCI1					3
-    OHCI1					4*
-    SS						5
-    DMA						6
-    BIST					7
-    MMC0					8
-    MMC1					9
-    MMC2					10
-    MMC3					11
-    MS						12**
-    NAND					13
-    SDRAM					14
-
-    ACE						16
-    EMAC					17
-    TS						18
-
-    SPI0					20
-    SPI1					21
-    SPI2					22
-    SPI3					23
-    PATA					24
-    SATA					25**
-    GPS						26*
-
-    VE						32
-    TVD						33
-    TVE0					34
-    TVE1					35
-    LCD0					36
-    LCD1					37
-
-    CSI0					40
-    CSI1					41
-
-    HDMI					43
-    DE_BE0					44
-    DE_BE1					45
-    DE_FE1					46
-    DE_FE1					47
-
-    MP						50
-
-    MALI400					52
-
-  * APB0 gates ("allwinner,sun4i-apb0-gates-clk")
-
-    CODEC					0
-    SPDIF					1*
-    AC97					2
-    IIS						3
-
-    PIO						5
-    IR0						6
-    IR1						7
-
-    KEYPAD					10
-
-  * APB1 gates ("allwinner,sun4i-apb1-gates-clk")
-
-    I2C0					0
-    I2C1					1
-    I2C2					2
-
-    CAN						4
-    SCR						5
-    PS20					6
-    PS21					7
-
-    UART0					16
-    UART1					17
-    UART2					18
-    UART3					19
-    UART4					20
-    UART5					21
-    UART6					22
-    UART7					23
-
-Notation:
- [*]:  The datasheet didn't mention these, but they are present on AW code
- [**]: The datasheet had this marked as "NC" but they are used on AW code

Documentation/devicetree/bindings/clock/sunxi/sun5i-a10s-gates.txt

-Gate clock outputs
-------------------
-
-  * AXI gates ("allwinner,sun4i-axi-gates-clk")
-
-    DRAM					0
-
-  * AHB gates ("allwinner,sun5i-a10s-ahb-gates-clk")
-
-    USB0					0
-    EHCI0					1
-    OHCI0					2
-
-    SS						5
-    DMA						6
-    BIST					7
-    MMC0					8
-    MMC1					9
-    MMC2					10
-
-    NAND					13
-    SDRAM					14
-
-    EMAC					17
-    TS						18
-
-    SPI0					20
-    SPI1					21
-    SPI2					22
-
-    GPS						26
-
-    HSTIMER					28
-
-    VE						32
-
-    TVE						34
-
-    LCD						36
-
-    CSI						40
-
-    HDMI					43
-    DE_BE					44
-
-    DE_FE					46
-
-    IEP						51
-    MALI400					52
-
-  * APB0 gates ("allwinner,sun5i-a10s-apb0-gates-clk")
-
-    CODEC					0
-
-    IIS						3
-
-    PIO						5
-    IR						6
-
-    KEYPAD					10
-
-  * APB1 gates ("allwinner,sun5i-a10s-apb1-gates-clk")
-
-    I2C0					0
-    I2C1					1
-    I2C2					2
-
-    UART0					16
-    UART1					17
-    UART2					18
-    UART3					19
-
-Notation:
- [*]:  The datasheet didn't mention these, but they are present on AW code
- [**]: The datasheet had this marked as "NC" but they are used on AW code

Documentation/devicetree/bindings/clock/sunxi/sun5i-a13-gates.txt

-Gate clock outputs
-------------------
-
-  * AXI gates ("allwinner,sun4i-axi-gates-clk")
-
-    DRAM					0
-
-  * AHB gates ("allwinner,sun5i-a13-ahb-gates-clk")
-
-    USBOTG					0
-    EHCI					1
-    OHCI					2
-
-    SS						5
-    DMA						6
-    BIST					7
-    MMC0					8
-    MMC1					9
-    MMC2					10
-
-    NAND					13
-    SDRAM					14
-
-    SPI0					20
-    SPI1					21
-    SPI2					22
-
-    STIMER					28
-
-    VE						32
-
-    LCD						36
-
-    CSI						40
-
-    DE_BE					44
-
-    DE_FE					46
-
-    IEP						51
-    MALI400					52
-
-  * APB0 gates ("allwinner,sun5i-a13-apb0-gates-clk")
-
-    CODEC					0
-
-    PIO						5
-    IR						6
-
-  * APB1 gates ("allwinner,sun5i-a13-apb1-gates-clk")
-
-    I2C0					0
-    I2C1					1
-    I2C2					2
-
-    UART1					17
-
-    UART3					19

Documentation/devicetree/bindings/clock/sunxi/sun6i-a31-gates.txt

-Gate clock outputs
-------------------
-
-  * AHB1 gates ("allwinner,sun6i-a31-ahb1-gates-clk")
-
-    MIPI DSI					1
-
-    SS						5
-    DMA						6
-
-    MMC0					8
-    MMC1					9
-    MMC2					10
-    MMC3					11
-
-    NAND1					12
-    NAND0					13
-    SDRAM					14
-
-    GMAC					17
-    TS						18
-    HSTIMER					19
-    SPI0					20
-    SPI1					21
-    SPI2					22
-    SPI3					23
-    USB_OTG					24
-
-    EHCI0					26
-    EHCI1					27
-
-    OHCI0					29
-    OHCI1					30
-    OHCI2					31
-    VE						32
-
-    LCD0					36
-    LCD1					37
-
-    CSI						40
-
-    HDMI					43
-    DE_BE0					44
-    DE_BE1					45
-    DE_FE1					46
-    DE_FE1					47
-
-    MP						50
-
-    GPU						52
-
-    DEU0					55
-    DEU1					56
-    DRC0					57
-    DRC1					58
-
-  * APB1 gates ("allwinner,sun6i-a31-apb1-gates-clk")
-
-    CODEC					0
-
-    DIGITAL MIC					4
-    PIO						5
-
-    DAUDIO0					12
-    DAUDIO1					13
-
-  * APB2 gates ("allwinner,sun6i-a31-apb2-gates-clk")
-
-    I2C0					0
-    I2C1					1
-    I2C2					2
-    I2C3					3
-
-    UART0					16
-    UART1					17
-    UART2					18
-    UART3					19
-    UART4					20
-    UART5					21
-
-Notation:
- [*]:  The datasheet didn't mention these, but they are present on AW code
- [**]: The datasheet had this marked as "NC" but they are used on AW code

Documentation/devicetree/bindings/clock/sunxi/sun7i-a20-gates.txt

-Gate clock outputs
-------------------
-
-  * AXI gates ("allwinner,sun4i-axi-gates-clk")
-
-    DRAM					0
-
-  * AHB gates ("allwinner,sun7i-a20-ahb-gates-clk")
-
-    USB0					0
-    EHCI0					1
-    OHCI0					2
-    EHCI1					3
-    OHCI1					4
-    SS						5
-    DMA						6
-    BIST					7
-    MMC0					8
-    MMC1					9
-    MMC2					10
-    MMC3					11
-    MS						12
-    NAND					13
-    SDRAM					14
-
-    ACE						16
-    EMAC					17
-    TS						18
-
-    SPI0					20
-    SPI1					21
-    SPI2					22
-    SPI3					23
-
-    SATA					25
-
-    HSTIMER					28
-
-    VE						32
-    TVD						33
-    TVE0					34
-    TVE1					35
-    LCD0					36
-    LCD1					37
-
-    CSI0					40
-    CSI1					41
-
-    HDMI1					42
-    HDMI0					43
-    DE_BE0					44
-    DE_BE1					45
-    DE_FE1					46
-    DE_FE1					47
-
-    GMAC					49
-    MP						50
-
-    MALI400					52
-
-  * APB0 gates ("allwinner,sun7i-a20-apb0-gates-clk")
-
-    CODEC					0
-    SPDIF					1
-    AC97					2
-    IIS0					3
-    IIS1					4
-    PIO						5
-    IR0						6
-    IR1						7
-    IIS2					8
-
-    KEYPAD					10
-
-  * APB1 gates ("allwinner,sun7i-a20-apb1-gates-clk")
-
-    I2C0					0
-    I2C1					1
-    I2C2					2
-    I2C3					3
-    CAN						4
-    SCR						5
-    PS20					6
-    PS21					7
-
-    I2C4					15
-    UART0					16
-    UART1					17
-    UART2					18
-    UART3					19
-    UART4					20
-    UART5					21
-    UART6					22
-    UART7					23
-
-Notation:
- [*]:  The datasheet didn't mention these, but they are present on AW code
- [**]: The datasheet had this marked as "NC" but they are used on AW code

Documentation/devicetree/bindings/interrupt-controller/allwinner,sun4i-ic.txt

@@ -8,9 +8,6 @@ Required properties:
 - #interrupt-cells : Specifies the number of cells needed to encode an
   interrupt source. The value shall be 1.
 
-For the valid interrupt sources for your SoC, see the documentation in
-sunxi/<soc>.txt
-
 Example:
 
 intc: interrupt-controller {

Documentation/devicetree/bindings/interrupt-controller/sunxi/sun4i-a10.txt

-Allwinner A10 (sun4i) interrupt sources
----------------------------------------
-
-The interrupt sources available for the Allwinner A10 SoC are the
-following one:
-
-0: ENMI
-1: UART0
-2: UART1
-3: UART2
-4: UART3
-5: IR0
-6: IR1
-7: I2C0
-8: I2C1
-9: I2C2
-10: SPI0
-11: SPI1
-12: SPI2
-13: SPDIF
-14: AC97
-15: TS
-16: I2S
-17: UART4
-18: UART5
-19: UART6
-20: UART7
-21: KEYPAD
-22: TIMER0
-23: TIMER1
-24: TIMER2
-25: TIMER3
-26: CAN
-27: DMA
-28: PIO
-29: TOUCH_PANEL
-30: AUDIO_CODEC
-31: LRADC
-32: MMC0
-33: MMC1
-34: MMC2
-35: MMC3
-36: MEMSTICK
-37: NAND
-38: USB0
-39: USB1
-40: USB2
-41: SCR
-42: CSI0
-43: CSI1
-44: LCDCTRL0
-45: LCDCTRL1
-46: MP
-47: DEFEBE0
-48: DEFEBE1
-49: PMU
-50: SPI3
-51: TZASC
-52: PATA
-53: VE
-54: SS
-55: EMAC
-56: SATA
-57: GPS
-58: HDMI
-59: TVE
-60: ACE
-61: TVD
-62: PS2_0
-63: PS2_1
-64: USB3
-65: USB4
-66: PLE_PFM
-67: TIMER4
-68: TIMER5
-69: GPU_GP
-70: GPU_GPMMU
-71: GPU_PP0
-72: GPU_PPMMU0
-73: GPU_PMU
-74: GPU_RSV0
-75: GPU_RSV1
-76: GPU_RSV2
-77: GPU_RSV3
-78: GPU_RSV4
-79: GPU_RSV5
-80: GPU_RSV6
-82: SYNC_TIMER0
-83: SYNC_TIMER1

Documentation/devicetree/bindings/interrupt-controller/sunxi/sun5i-a13.txt

-Allwinner A13 (sun5i) interrupt sources
----------------------------------------
-
-The interrupt sources available for the Allwinner A13 SoC are the
-following one:
-
-0: ENMI
-2: UART1
-4: UART3
-5: IR
-7: I2C0
-8: I2C1
-9: I2C2
-10: SPI0
-11: SPI1
-12: SPI2
-22: TIMER0
-23: TIMER1
-24: TIMER2
-25: TIMER3
-27: DMA
-28: PIO
-29: TOUCH_PANEL
-30: AUDIO_CODEC
-31: LRADC
-32: MMC0
-33: MMC1
-34: MMC2
-37: NAND
-38: USB OTG
-39: USB EHCI
-40: USB OHCI
-42: CSI
-44: LCDCTRL
-47: DEFEBE
-49: PMU
-53: VE
-54: SS
-66: PLE_PFM
-67: TIMER4
-68: TIMER5
-69: GPU_GP
-70: GPU_GPMMU
-71: GPU_PP0
-72: GPU_PPMMU0
-73: GPU_PMU
-74: GPU_RSV0
-75: GPU_RSV1
-76: GPU_RSV2
-77: GPU_RSV3
-78: GPU_RSV4
-79: GPU_RSV5
-80: GPU_RSV6
-82: SYNC_TIMER0
-83: SYNC_TIMER1

arch/arm/Kconfig

@@ -317,6 +317,7 @@ config ARCH_INTEGRATOR
 	select NEED_MACH_MEMORY_H
 	select PLAT_VERSATILE
 	select SPARSE_IRQ
+	select USE_OF
 	select VERSATILE_FPGA_IRQ
 	help
 	  Support for ARM's Integrator platform.
@@ -723,6 +724,7 @@ config ARCH_S3C64XX
 	select ARM_VIC
 	select CLKDEV_LOOKUP
 	select CLKSRC_SAMSUNG_PWM
+	select COMMON_CLK
 	select CPU_V6
 	select GENERIC_CLOCKEVENTS
 	select GPIO_SAMSUNG
@@ -736,7 +738,6 @@ config ARCH_S3C64XX
 	select S3C_DEV_NAND
 	select S3C_GPIO_TRACK
 	select SAMSUNG_ATAGS
-	select SAMSUNG_CLKSRC
 	select SAMSUNG_GPIOLIB_4BIT
 	select SAMSUNG_WAKEMASK
 	select SAMSUNG_WDT_RESET

arch/arm/Kconfig.debug

@@ -386,6 +386,13 @@ choice
 		  when u-boot hands over to the kernel, the system
 		  silently crashes, with no serial output at all.
 
+	config DEBUG_VF_UART
+		bool "Vybrid UART"
+		depends on SOC_VF610
+		help
+		  Say Y here if you want kernel low-level debugging support
+		  on Vybrid based platforms.
+
 	config DEBUG_NOMADIK_UART
 		bool "Kernel low-level debugging messages via NOMADIK UART"
 		depends on ARCH_NOMADIK
@@ -906,6 +913,7 @@ config DEBUG_LL_INCLUDE
 	default "debug/tegra.S" if DEBUG_TEGRA_UART
 	default "debug/ux500.S" if DEBUG_UX500_UART
 	default "debug/vexpress.S" if DEBUG_VEXPRESS_UART0_DETECT
+	default "debug/vf.S" if DEBUG_VF_UART
 	default "debug/vt8500.S" if DEBUG_VT8500_UART0
 	default "debug/zynq.S" if DEBUG_ZYNQ_UART0 || DEBUG_ZYNQ_UART1
 	default "mach/debug-macro.S"

arch/arm/boot/dts/ecx-common.dtsi

@@ -19,6 +19,14 @@ chosen {
 		bootargs = "console=ttyAMA0";
 	};
 
+	psci {
+		compatible	= "arm,psci";
+		method		= "smc";
+		cpu_suspend	= <0x84000002>;
+		cpu_off		= <0x84000004>;
+		cpu_on		= <0x84000006>;
+	};
+
 	soc {
 		#address-cells = <1>;
 		#size-cells = <1>;

arch/arm/boot/dts/imx6sl.dtsi

@@ -380,7 +380,9 @@ clks: ccm@020c4000 {
 			};
 
 			anatop: anatop@020c8000 {
-				compatible = "fsl,imx6sl-anatop", "syscon", "simple-bus";
+				compatible = "fsl,imx6sl-anatop",
+					     "fsl,imx6q-anatop",
+					     "syscon", "simple-bus";
 				reg = <0x020c8000 0x1000>;
 				interrupts = <0 49 0x04 0 54 0x04 0 127 0x04>;
 

arch/arm/boot/dts/integrator.dtsi

@@ -5,6 +5,11 @@
 /include/ "skeleton.dtsi"
 
 / {
+	core-module@10000000 {
+		compatible = "arm,core-module-integrator";
+		reg = <0x10000000 0x200>;
+	};
+
 	timer@13000000 {
 		reg = <0x13000000 0x100>;
 		interrupt-parent = <&pic>;

arch/arm/boot/dts/integratorap.dts

@@ -19,8 +19,11 @@ chosen {
 	};
 
 	syscon {
-		/* AP system controller registers */
+		compatible = "arm,integrator-ap-syscon";
 		reg = <0x11000000 0x100>;
+		interrupt-parent = <&pic>;
+		/* These are the logical module IRQs */
+		interrupts = <9>, <10>, <11>, <12>;
 	};
 
 	timer0: timer@13000000 {

arch/arm/boot/dts/integratorcp.dts

@@ -13,8 +13,8 @@ chosen {
 		bootargs = "root=/dev/ram0 console=ttyAMA0,38400n8 earlyprintk";
 	};
 
-	cpcon {
-		/* CP controller registers */
+	syscon {
+		compatible = "arm,integrator-cp-syscon";
 		reg = <0xcb000000 0x100>;
 	};
 

arch/arm/boot/dts/keystone.dts

@@ -100,13 +100,15 @@ rstctrl: reset-controller {
 			reg = <0x023100e8 4>;	/* pll reset control reg */
 		};
 
+		/include/ "keystone-clocks.dtsi"
+
 		uart0: serial@02530c00 {
 			compatible = "ns16550a";
 			current-speed = <115200>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			reg = <0x02530c00 0x100>;
-			clock-frequency = <133120000>;
+			clocks	= <&clkuart0>;
 			interrupts = <GIC_SPI 277 IRQ_TYPE_EDGE_RISING>;
 		};
 
@@ -116,9 +118,66 @@ uart1:	serial@02531000 {
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			reg = <0x02531000 0x100>;
-			clock-frequency = <133120000>;
+			clocks	= <&clkuart1>;
 			interrupts = <GIC_SPI 280 IRQ_TYPE_EDGE_RISING>;
 		};
 
+		i2c0: i2c@2530000 {
+			compatible = "ti,davinci-i2c";
+			reg = <0x02530000 0x400>;
+			clock-frequency = <100000>;
+			clocks = <&clki2c>;
+			interrupts = <GIC_SPI 283 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			dtt@50 {
+				compatible = "at,24c1024";
+				reg = <0x50>;
+			};
+		};
+
+		i2c1: i2c@2530400 {
+			compatible = "ti,davinci-i2c";
+			reg = <0x02530400 0x400>;
+			clock-frequency = <100000>;
+			clocks = <&clki2c>;
+			interrupts = <GIC_SPI 286 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		i2c2: i2c@2530800 {
+			compatible = "ti,davinci-i2c";
+			reg = <0x02530800 0x400>;
+			clock-frequency = <100000>;
+			clocks = <&clki2c>;
+			interrupts = <GIC_SPI 289 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		spi0: spi@21000400 {
+			compatible = "ti,dm6441-spi";
+			reg = <0x21000400 0x200>;
+			num-cs = <4>;
+			ti,davinci-spi-intr-line = <0>;
+			interrupts = <GIC_SPI 292 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&clkspi>;
+		};
+
+		spi1: spi@21000600 {
+			compatible = "ti,dm6441-spi";
+			reg = <0x21000600 0x200>;
+			num-cs = <4>;
+			ti,davinci-spi-intr-line = <0>;
+			interrupts = <GIC_SPI 296 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&clkspi>;
+		};
+
+		spi2: spi@21000800 {
+			compatible = "ti,dm6441-spi";
+			reg = <0x21000800 0x200>;
+			num-cs = <4>;
+			ti,davinci-spi-intr-line = <0>;
+			interrupts = <GIC_SPI 300 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&clkspi>;
+		};
 	};
 };

arch/arm/boot/dts/r7s72100.dtsi

+/*
+ * Device Tree Source for the r7s72100 SoC
+ *
+ * Copyright (C) 2013 Renesas Solutions Corp.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/ {
+	compatible = "renesas,r7s72100";
+	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0>;
+		};
+	};
+
+	gic: interrupt-controller@e8201000 {
+		compatible = "arm,cortex-a9-gic";
+		#interrupt-cells = <3>;
+		#address-cells = <0>;
+		interrupt-controller;
+		reg = <0xe8201000 0x1000>,
+			<0xe8202000 0x1000>;
+	};
+};

arch/arm/boot/dts/r8a7791.dtsi

+/*
+ * Device Tree Source for the r8a7791 SoC
+ *
+ * Copyright (C) 2013 Renesas Electronics Corporation
+ * Copyright (C) 2013 Renesas Solutions Corp.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/ {
+	compatible = "renesas,r8a7791";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <0>;
+			clock-frequency = <1300000000>;
+		};
+	};
+
+	gic: interrupt-controller@f1001000 {
+		compatible = "arm,cortex-a15-gic";
+		#interrupt-cells = <3>;
+		#address-cells = <0>;
+		interrupt-controller;
+		reg = <0 0xf1001000 0 0x1000>,
+			<0 0xf1002000 0 0x1000>,
+			<0 0xf1004000 0 0x2000>,
+			<0 0xf1006000 0 0x2000>;
+		interrupts = <1 9 0xf04>;
+	};
+};

arch/arm/configs/bcm_defconfig

-CONFIG_EXPERIMENTAL=y
 # CONFIG_LOCALVERSION_AUTO is not set
 # CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
@@ -25,10 +24,9 @@ CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
 # CONFIG_BLK_DEV_BSG is not set
 CONFIG_PARTITION_ADVANCED=y
-CONFIG_EFI_PARTITION=y
 CONFIG_ARCH_BCM=y
+CONFIG_ARCH_BCM_MOBILE=y
 CONFIG_ARM_THUMBEE=y
-CONFIG_ARM_ERRATA_743622=y
 CONFIG_PREEMPT=y
 CONFIG_AEABI=y
 # CONFIG_OABI_COMPAT is not set
@@ -50,7 +48,6 @@ CONFIG_UNIX_DIAG=y
 CONFIG_NET_KEY=y
 CONFIG_INET=y
 CONFIG_IP_MULTICAST=y
-CONFIG_ARPD=y
 CONFIG_SYN_COOKIES=y
 CONFIG_TCP_MD5SIG=y
 CONFIG_IPV6=y
@@ -95,7 +92,6 @@ CONFIG_MMC_UNSAFE_RESUME=y
 CONFIG_MMC_BLOCK_MINORS=32
 CONFIG_MMC_TEST=y
 CONFIG_MMC_SDHCI=y
-CONFIG_MMC_SDHCI_PLTFM=y
 CONFIG_MMC_SDHCI_BCM_KONA=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
@@ -117,12 +113,12 @@ CONFIG_CONFIGFS_FS=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_PRINTK_TIME=y
-CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_INFO=y
 CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
 CONFIG_DETECT_HUNG_TASK=y
 CONFIG_DEFAULT_HUNG_TASK_TIMEOUT=110
 CONFIG_BOOTPARAM_HUNG_TASK_PANIC=y
-CONFIG_DEBUG_INFO=y
 # CONFIG_FTRACE is not set
 CONFIG_CRC_CCITT=y
 CONFIG_CRC_T10DIF=y

arch/arm/configs/imx_v6_v7_defconfig

@@ -132,7 +132,6 @@ CONFIG_TOUCHSCREEN_MC13783=y
 CONFIG_INPUT_MISC=y
 CONFIG_INPUT_MMA8450=y
 CONFIG_SERIO_SERPORT=m
-CONFIG_VT_HW_CONSOLE_BINDING=y
 # CONFIG_LEGACY_PTYS is not set
 # CONFIG_DEVKMEM is not set
 CONFIG_SERIAL_IMX=y
@@ -188,22 +187,33 @@ CONFIG_SND_SOC_PHYCORE_AC97=y
 CONFIG_SND_SOC_EUKREA_TLV320=y
 CONFIG_SND_SOC_IMX_WM8962=y
 CONFIG_SND_SOC_IMX_SGTL5000=y
+CONFIG_SND_SOC_IMX_SPDIF=y
 CONFIG_SND_SOC_IMX_MC13783=y
 CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_MXC=y
 CONFIG_USB_STORAGE=y
 CONFIG_USB_CHIPIDEA=y
+CONFIG_USB_CHIPIDEA_UDC=y
 CONFIG_USB_CHIPIDEA_HOST=y
-CONFIG_USB_PHY=y
 CONFIG_NOP_USB_XCEIV=y
 CONFIG_USB_MXS_PHY=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_ETH=m
+CONFIG_USB_MASS_STORAGE=m
 CONFIG_MMC=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_PLTFM=y
 CONFIG_MMC_SDHCI_ESDHC_IMX=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_ONESHOT=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_BACKLIGHT=y
+CONFIG_LEDS_TRIGGER_GPIO=y
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_INTF_DEV_UIE_EMUL=y
 CONFIG_RTC_DRV_MC13XXX=y
@@ -246,7 +256,6 @@ CONFIG_UDF_FS=m
 CONFIG_MSDOS_FS=m
 CONFIG_VFAT_FS=y
 CONFIG_TMPFS=y
-CONFIG_CONFIGFS_FS=m
 CONFIG_JFFS2_FS=y
 CONFIG_UBIFS_FS=y
 CONFIG_NFS_FS=y
@@ -261,6 +270,7 @@ CONFIG_NLS_ISO8859_15=m
 CONFIG_NLS_UTF8=y
 CONFIG_MAGIC_SYSRQ=y
 # CONFIG_SCHED_DEBUG is not set
+CONFIG_PROVE_LOCKING=y
 # CONFIG_DEBUG_BUGVERBOSE is not set
 # CONFIG_FTRACE is not set
 # CONFIG_ARM_UNWIND is not set

arch/arm/configs/integrator_defconfig

-CONFIG_EXPERIMENTAL=y
 CONFIG_SYSVIPC=y
-CONFIG_TINY_RCU=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_ARCH_INTEGRATOR=y
 CONFIG_ARCH_INTEGRATOR_AP=y
 CONFIG_ARCH_INTEGRATOR_CP=y
+CONFIG_INTEGRATOR_IMPD1=y
 CONFIG_CPU_ARM720T=y
 CONFIG_CPU_ARM920T=y
 CONFIG_CPU_ARM922T=y
@@ -18,12 +20,9 @@ CONFIG_CPU_ARM1020=y
 CONFIG_CPU_ARM1022=y
 CONFIG_CPU_ARM1026=y
 CONFIG_PCI=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
 CONFIG_PREEMPT=y
 CONFIG_AEABI=y
-CONFIG_LEDS=y
-CONFIG_LEDS_CPU=y
+# CONFIG_ATAGS is not set
 CONFIG_ZBOOT_ROM_TEXT=0x0
 CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_CMDLINE="console=ttyAM0,38400n8 root=/dev/nfs ip=bootp"
@@ -44,24 +43,20 @@ CONFIG_IP_PNP_BOOTP=y
 CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_AFS_PARTS=y
-CONFIG_MTD_CHAR=y
 CONFIG_MTD_BLOCK=y
 CONFIG_MTD_CFI=y
 CONFIG_MTD_CFI_ADV_OPTIONS=y
 CONFIG_MTD_CFI_INTELEXT=y
 CONFIG_MTD_PHYSMAP=y
+CONFIG_PROC_DEVICETREE=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=8192
 CONFIG_NETDEVICES=y
-CONFIG_NET_ETHERNET=y
-CONFIG_NET_PCI=y
 CONFIG_E100=y
 CONFIG_SMC91X=y
 # CONFIG_KEYBOARD_ATKBD is not set
 # CONFIG_SERIO_SERPORT is not set
-CONFIG_SERIAL_AMBA_PL010=y
-CONFIG_SERIAL_AMBA_PL010_CONSOLE=y
 CONFIG_FB=y
 CONFIG_FB_MODE_HELPERS=y
 CONFIG_FB_ARMCLCD=y
@@ -71,19 +66,23 @@ CONFIG_FB_MATROX_MYSTIQUE=y
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_MMC=y
 CONFIG_MMC_ARMMMCI=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_CPU=y
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_DRV_PL030=y
+CONFIG_COMMON_CLK_DEBUG=y
 CONFIG_EXT2_FS=y
 CONFIG_VFAT_FS=y
 CONFIG_TMPFS=y
 CONFIG_JFFS2_FS=y
 CONFIG_CRAMFS=y
 CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
 CONFIG_ROOT_NFS=y
 CONFIG_NFSD=y
 CONFIG_NFSD_V3=y
-CONFIG_PARTITION_ADVANCED=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_MAGIC_SYSRQ=y

arch/arm/configs/keystone_defconfig

@@ -123,7 +123,9 @@ CONFIG_SERIAL_OF_PLATFORM=y
 CONFIG_I2C=y
 # CONFIG_I2C_COMPAT is not set
 CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_DAVINCI=y
 CONFIG_SPI=y
+CONFIG_SPI_DAVINCI=y
 CONFIG_SPI_SPIDEV=y
 # CONFIG_HWMON is not set
 CONFIG_WATCHDOG=y

arch/arm/configs/multi_v7_defconfig

@@ -6,6 +6,7 @@ CONFIG_ARCH_MVEBU=y
 CONFIG_MACH_ARMADA_370=y
 CONFIG_MACH_ARMADA_XP=y
 CONFIG_ARCH_BCM=y
+CONFIG_ARCH_BCM_MOBILE=y
 CONFIG_GPIO_PCA953X=y
 CONFIG_ARCH_HIGHBANK=y
 CONFIG_ARCH_KEYSTONE=y

arch/arm/configs/mxs_defconfig

@@ -76,7 +76,6 @@ CONFIG_INPUT_EVDEV=y
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_TSC2007=m
 # CONFIG_SERIO is not set
-CONFIG_VT_HW_CONSOLE_BINDING=y
 CONFIG_DEVPTS_MULTIPLE_INSTANCES=y
 # CONFIG_LEGACY_PTYS is not set
 # CONFIG_DEVKMEM is not set
@@ -91,7 +90,6 @@ CONFIG_I2C_MXS=y
 CONFIG_SPI=y
 CONFIG_SPI_GPIO=m
 CONFIG_SPI_MXS=y
-CONFIG_DEBUG_GPIO=y
 CONFIG_GPIO_SYSFS=y
 # CONFIG_HWMON is not set
 CONFIG_WATCHDOG=y
@@ -115,9 +113,12 @@ CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_STORAGE=y
 CONFIG_USB_CHIPIDEA=y
+CONFIG_USB_CHIPIDEA_UDC=y
 CONFIG_USB_CHIPIDEA_HOST=y
-CONFIG_USB_PHY=y
 CONFIG_USB_MXS_PHY=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_ETH=m
+CONFIG_USB_MASS_STORAGE=m
 CONFIG_MMC=y
 CONFIG_MMC_UNSAFE_RESUME=y
 CONFIG_MMC_MXS=y

arch/arm/configs/sunxi_defconfig

+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_SMP=y
+CONFIG_AEABI=y
+CONFIG_HIGHMEM=y
+CONFIG_HIGHPTE=y
+CONFIG_VFP=y
+CONFIG_NEON=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_WIRELESS is not set
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_NETDEVICES=y
+CONFIG_SUN4I_EMAC=y
+# CONFIG_NET_CADENCE is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+# CONFIG_WLAN is not set
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=8
+CONFIG_SERIAL_8250_RUNTIME_UARTS=8
+CONFIG_SERIAL_8250_DW=y
+CONFIG_I2C=y
+# CONFIG_I2C_COMPAT is not set
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_MV64XXX=y
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_SUNXI_WATCHDOG=y
+# CONFIG_USB_SUPPORT is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_COMMON_CLK_DEBUG=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_NLS=y

arch/arm/configs/vexpress_defconfig

-CONFIG_EXPERIMENTAL=y
 # CONFIG_LOCALVERSION_AUTO is not set
 CONFIG_SYSVIPC=y
 CONFIG_IKCONFIG=y
@@ -8,11 +7,9 @@ CONFIG_CGROUPS=y
 CONFIG_CPUSETS=y
 # CONFIG_UTS_NS is not set
 # CONFIG_IPC_NS is not set
-# CONFIG_USER_NS is not set
 # CONFIG_PID_NS is not set
 # CONFIG_NET_NS is not set
 CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
 CONFIG_PROFILING=y
 CONFIG_OPROFILE=y
 CONFIG_MODULES=y
@@ -23,14 +20,22 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_IOSCHED_CFQ is not set
 CONFIG_ARCH_VEXPRESS=y
 CONFIG_ARCH_VEXPRESS_CA9X4=y
+CONFIG_ARCH_VEXPRESS_DCSCB=y
+CONFIG_ARCH_VEXPRESS_TC2_PM=y
 # CONFIG_SWP_EMULATE is not set
 CONFIG_SMP=y
+CONFIG_HAVE_ARM_ARCH_TIMER=y
+CONFIG_MCPM=y
 CONFIG_VMSPLIT_2G=y
-CONFIG_HOTPLUG_CPU=y
+CONFIG_NR_CPUS=8
+CONFIG_ARM_PSCI=y
 CONFIG_AEABI=y
+CONFIG_CMA=y
 CONFIG_ZBOOT_ROM_TEXT=0x0
 CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="root=/dev/nfs nfsroot=10.1.69.3:/work/nfsroot ip=dhcp console=ttyAMA0 mem=128M"
+CONFIG_CMDLINE="console=ttyAMA0"
+CONFIG_CPU_IDLE=y
+CONFIG_CPU_IDLE_MULTIPLE_DRIVERS=y
 CONFIG_VFP=y
 CONFIG_NEON=y
 # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
@@ -44,37 +49,46 @@ CONFIG_IP_PNP_BOOTP=y
 # CONFIG_INET_LRO is not set
 # CONFIG_IPV6 is not set
 # CONFIG_WIRELESS is not set
+CONFIG_NET_9P=y
+CONFIG_NET_9P_VIRTIO=y
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
 CONFIG_MTD=y
-CONFIG_MTD_CONCAT=y
-CONFIG_MTD_PARTITIONS=y
 CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_CHAR=y
 CONFIG_MTD_BLOCK=y
 CONFIG_MTD_CFI=y
 CONFIG_MTD_CFI_INTELEXT=y
 CONFIG_MTD_CFI_AMDSTD=y
-CONFIG_MTD_ARM_INTEGRATOR=y
-CONFIG_MISC_DEVICES=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_PHYSMAP_OF=y
+CONFIG_MTD_PLATRAM=y
+CONFIG_MTD_UBI=y
+CONFIG_PROC_DEVICETREE=y
+CONFIG_VIRTIO_BLK=y
 # CONFIG_SCSI_PROC_FS is not set
 CONFIG_BLK_DEV_SD=y
-# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_SCSI_VIRTIO=y
 CONFIG_ATA=y
 # CONFIG_SATA_PMP is not set
 CONFIG_NETDEVICES=y
-CONFIG_NET_ETHERNET=y
+CONFIG_VIRTIO_NET=y
+CONFIG_SMC91X=y
 CONFIG_SMSC911X=y
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
 # CONFIG_WLAN is not set
 CONFIG_INPUT_EVDEV=y
 # CONFIG_SERIO_SERPORT is not set
 CONFIG_SERIO_AMBAKMI=y
+CONFIG_LEGACY_PTY_COUNT=16
 CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
-CONFIG_LEGACY_PTY_COUNT=16
-# CONFIG_HW_RANDOM is not set
-# CONFIG_HWMON is not set
+CONFIG_VIRTIO_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_HW_RANDOM_VIRTIO=y
+CONFIG_I2C=y
+CONFIG_I2C_VERSATILE=y
+CONFIG_SENSORS_VEXPRESS=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_VEXPRESS=y
 CONFIG_FB=y
 CONFIG_FB_ARMCLCD=y
 CONFIG_FRAMEBUFFER_CONSOLE=y
@@ -103,38 +117,45 @@ CONFIG_HID_THRUSTMASTER=y
 CONFIG_HID_ZEROPLUS=y
 CONFIG_USB=y
 CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
-# CONFIG_USB_DEVICE_CLASS is not set
 CONFIG_USB_MON=y
 CONFIG_USB_ISP1760_HCD=y
 CONFIG_USB_STORAGE=y
 CONFIG_MMC=y
 CONFIG_MMC_ARMMMCI=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_CPU=y
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_DRV_PL031=y
+CONFIG_VIRTIO_BALLOON=y
+CONFIG_VIRTIO_MMIO=y
+CONFIG_VIRTIO_MMIO_CMDLINE_DEVICES=y
 CONFIG_EXT2_FS=y
 CONFIG_EXT3_FS=y
 # CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
 # CONFIG_EXT3_FS_XATTR is not set
+CONFIG_EXT4_FS=y
 CONFIG_VFAT_FS=y
 CONFIG_TMPFS=y
 CONFIG_JFFS2_FS=y
+CONFIG_UBIFS_FS=y
 CONFIG_CRAMFS=y
+CONFIG_SQUASHFS=y
+CONFIG_SQUASHFS_LZO=y
 CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
 CONFIG_ROOT_NFS=y
-# CONFIG_RPCSEC_GSS_KRB5 is not set
+CONFIG_9P_FS=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
-CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_INFO=y
 CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
 CONFIG_DETECT_HUNG_TASK=y
 # CONFIG_SCHED_DEBUG is not set
-CONFIG_DEBUG_INFO=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
 CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_ERRORS=y
-CONFIG_DEBUG_LL=y
-CONFIG_EARLY_PRINTK=y
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
 # CONFIG_CRYPTO_HW is not set

arch/arm/include/debug/vf.S

+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+	.macro	addruart, rp, rv, tmp
+	ldr	\rp, =0x40028000	@ physical
+	ldr	\rv, =0xfe028000	@ virtual
+	.endm
+
+	.macro	senduart, rd, rx
+	strb	\rd, [\rx, #0x7]	@ Data Register
+	.endm
+
+	.macro	busyuart, rd, rx
+1001:	ldrb	\rd, [\rx, #0x4]	@ Status Register 1
+	tst	\rd, #1 << 6		@ TC
+	beq	1001b			@ wait until transmit done
+	.endm
+
+	.macro	waituart,rd,rx
+	.endm

arch/arm/kernel/psci_smp.c

@@ -14,7 +14,6 @@
  */
 
 #include <linux/init.h>
-#include <linux/irqchip/arm-gic.h>
 #include <linux/smp.h>
 #include <linux/of.h>
 

arch/arm/mach-bcm/Kconfig

 config ARCH_BCM
-	bool "Broadcom SoC" if ARCH_MULTI_V7
+	bool "Broadcom SoC Support"
+	depends on ARCH_MULTIPLATFORM
+	help
+	  This enables support for Broadcom ARM based SoC
+          chips
+
+if ARCH_BCM
+
+menu "Broadcom SoC Selection"
+
+config ARCH_BCM_MOBILE
+	bool "Broadcom Mobile SoC" if ARCH_MULTI_V7
 	depends on MMU
 	select ARCH_REQUIRE_GPIOLIB
 	select ARM_ERRATA_754322
@@ -9,12 +20,17 @@ config ARCH_BCM
 	select CLKSRC_OF
 	select GENERIC_CLOCKEVENTS
 	select GENERIC_TIME
-	select GPIO_BCM
+	select GPIO_BCM_KONA
 	select SPARSE_IRQ
 	select TICK_ONESHOT
 	select CACHE_L2X0
+	select HAVE_ARM_ARCH_TIMER
 	help
-	  This enables support for system based on Broadcom SoCs.
+	  This enables support for systems based on Broadcom mobile SoCs.
 	  It currently supports the 'BCM281XX' family, which includes
 	  BCM11130, BCM11140, BCM11351, BCM28145 and
 	  BCM28155 variants.
+
+endmenu
+
+endif

arch/arm/mach-bcm/Makefile

@@ -10,6 +10,6 @@
 # of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 # GNU General Public License for more details.
 
-obj-$(CONFIG_ARCH_BCM)		:= board_bcm281xx.o bcm_kona_smc.o bcm_kona_smc_asm.o kona.o
+obj-$(CONFIG_ARCH_BCM_MOBILE)	:= board_bcm281xx.o bcm_kona_smc.o bcm_kona_smc_asm.o kona.o
 plus_sec := $(call as-instr,.arch_extension sec,+sec)
 AFLAGS_bcm_kona_smc_asm.o	:=-Wa,-march=armv7-a$(plus_sec)

arch/arm/mach-bcm/board_bcm281xx.c

@@ -67,7 +67,7 @@ static void __init board_init(void)
 
 static const char * const bcm11351_dt_compat[] = { "brcm,bcm11351", NULL, };
 
-DT_MACHINE_START(BCM11351_DT, "Broadcom Application Processor")
+DT_MACHINE_START(BCM11351_DT, "BCM281xx Broadcom Application Processor")
 	.init_machine = board_init,
 	.restart = bcm_kona_restart,
 	.dt_compat = bcm11351_dt_compat,

arch/arm/mach-davinci/board-da830-evm.c

@@ -74,7 +74,7 @@ static int da830_evm_usb_ocic_notify(da8xx_ocic_handler_t handler)
 	if (handler != NULL) {
 		da830_evm_usb_ocic_handler = handler;
 
-		error = request_irq(irq, da830_evm_usb_ocic_irq, IRQF_DISABLED |
+		error = request_irq(irq, da830_evm_usb_ocic_irq,
 				    IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
 				    "OHCI over-current indicator", NULL);
 		if (error)

arch/arm/mach-davinci/board-omapl138-hawk.c

@@ -211,7 +211,7 @@ static int hawk_usb_ocic_notify(da8xx_ocic_handler_t handler)
 		hawk_usb_ocic_handler = handler;
 
 		error = request_irq(irq, omapl138_hawk_usb_ocic_irq,
-					IRQF_DISABLED | IRQF_TRIGGER_RISING |
+					IRQF_TRIGGER_RISING |
 					IRQF_TRIGGER_FALLING,
 					"OHCI over-current indicator", NULL);
 		if (error)

arch/arm/mach-davinci/time.c

@@ -181,7 +181,7 @@ static struct timer_s timers[] = {
 		.name      = "clockevent",
 		.opts      = TIMER_OPTS_DISABLED,
 		.irqaction = {
-			.flags   = IRQF_DISABLED | IRQF_TIMER,
+			.flags   = IRQF_TIMER,
 			.handler = timer_interrupt,
 		}
 	},
@@ -190,7 +190,7 @@ static struct timer_s timers[] = {
 		.period     = ~0,
 		.opts       = TIMER_OPTS_PERIODIC,
 		.irqaction = {
-			.flags   = IRQF_DISABLED | IRQF_TIMER,
+			.flags   = IRQF_TIMER,
 			.handler = freerun_interrupt,
 		}
 	},
@@ -331,7 +331,6 @@ static void davinci_set_mode(enum clock_event_mode mode,
 
 static struct clock_event_device clockevent_davinci = {
 	.features       = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
-	.shift		= 32,
 	.set_next_event	= davinci_set_next_event,
 	.set_mode	= davinci_set_mode,
 };
@@ -397,14 +396,10 @@ void __init davinci_timer_init(void)
 
 	/* setup clockevent */
 	clockevent_davinci.name = id_to_name[timers[TID_CLOCKEVENT].id];
-	clockevent_davinci.mult = div_sc(davinci_clock_tick_rate, NSEC_PER_SEC,
-					 clockevent_davinci.shift);
-	clockevent_davinci.max_delta_ns =
-		clockevent_delta2ns(0xfffffffe, &clockevent_davinci);
-	clockevent_davinci.min_delta_ns = 50000; /* 50 usec */
 
 	clockevent_davinci.cpumask = cpumask_of(0);
-	clockevents_register_device(&clockevent_davinci);
+	clockevents_config_and_register(&clockevent_davinci,
+					davinci_clock_tick_rate, 1, 0xfffffffe);
 
 	for (i=0; i< ARRAY_SIZE(timers); i++)
 		timer32_config(&timers[i]);

arch/arm/mach-highbank/Kconfig

@@ -10,6 +10,7 @@ config ARCH_HIGHBANK
 	select ARM_ERRATA_775420
 	select ARM_ERRATA_798181
 	select ARM_GIC
+	select ARM_PSCI
 	select ARM_TIMER_SP804
 	select CACHE_L2X0
 	select COMMON_CLK

arch/arm/mach-highbank/Makefile

@@ -3,6 +3,4 @@ obj-y					:= highbank.o system.o smc.o
 plus_sec := $(call as-instr,.arch_extension sec,+sec)
 AFLAGS_smc.o				:=-Wa,-march=armv7-a$(plus_sec)
 
-obj-$(CONFIG_SMP)			+= platsmp.o
-obj-$(CONFIG_HOTPLUG_CPU)		+= hotplug.o
 obj-$(CONFIG_PM_SLEEP)			+= pm.o

arch/arm/mach-highbank/core.h

@@ -3,7 +3,6 @@
 
 #include <linux/reboot.h>
 
-extern void highbank_set_cpu_jump(int cpu, void *jump_addr);
 extern void highbank_restart(enum reboot_mode, const char *);
 extern void __iomem *scu_base_addr;
 
@@ -14,8 +13,5 @@ static inline void highbank_pm_init(void) {}
 #endif
 
 extern void highbank_smc1(int fn, int arg);
-extern void highbank_cpu_die(unsigned int cpu);
-
-extern struct smp_operations highbank_smp_ops;
 
 #endif

arch/arm/mach-highbank/highbank.c

@@ -24,10 +24,9 @@
 #include <linux/of_platform.h>
 #include <linux/of_address.h>
 #include <linux/amba/bus.h>
+#include <linux/platform_device.h>
 
-#include <asm/cacheflush.h>
-#include <asm/cputype.h>
-#include <asm/smp_plat.h>
+#include <asm/psci.h>
 #include <asm/hardware/cache-l2x0.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
@@ -48,17 +47,6 @@ static void __init highbank_scu_map_io(void)
 	scu_base_addr = ioremap(base, SZ_4K);
 }
 
-#define HB_JUMP_TABLE_PHYS(cpu)		(0x40 + (0x10 * (cpu)))
-#define HB_JUMP_TABLE_VIRT(cpu)		phys_to_virt(HB_JUMP_TABLE_PHYS(cpu))
-
-void highbank_set_cpu_jump(int cpu, void *jump_addr)
-{
-	cpu = MPIDR_AFFINITY_LEVEL(cpu_logical_map(cpu), 0);
-	writel(virt_to_phys(jump_addr), HB_JUMP_TABLE_VIRT(cpu));
-	__cpuc_flush_dcache_area(HB_JUMP_TABLE_VIRT(cpu), 16);
-	outer_clean_range(HB_JUMP_TABLE_PHYS(cpu),
-			  HB_JUMP_TABLE_PHYS(cpu) + 15);
-}
 
 static void highbank_l2x0_disable(void)
 {
@@ -138,6 +126,10 @@ static struct notifier_block highbank_platform_nb = {
 	.notifier_call = highbank_platform_notifier,
 };
 
+static struct platform_device highbank_cpuidle_device = {
+	.name = "cpuidle-calxeda",
+};
+
 static void __init highbank_init(void)
 {
 	struct device_node *np;
@@ -154,6 +146,9 @@ static void __init highbank_init(void)
 	bus_register_notifier(&amba_bustype, &highbank_amba_nb);
 
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
+
+	if (psci_ops.cpu_suspend)
+		platform_device_register(&highbank_cpuidle_device);
 }
 
 static const char *highbank_match[] __initconst = {
@@ -166,7 +161,6 @@ DT_MACHINE_START(HIGHBANK, "Highbank")
 #if defined(CONFIG_ZONE_DMA) && defined(CONFIG_ARM_LPAE)
 	.dma_zone_size	= (4ULL * SZ_1G),
 #endif
-	.smp		= smp_ops(highbank_smp_ops),
 	.init_irq	= highbank_init_irq,
 	.init_machine	= highbank_init,
 	.dt_compat	= highbank_match,

arch/arm/mach-highbank/hotplug.c

-/*
- * Copyright 2011 Calxeda, Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms and conditions of the GNU General Public License,
- * version 2, as published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
- * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program.  If not, see <http://www.gnu.org/licenses/>.
- */
-#include <linux/kernel.h>
-#include <asm/cacheflush.h>
-
-#include "core.h"
-#include "sysregs.h"
-
-extern void secondary_startup(void);
-
-/*
- * platform-specific code to shutdown a CPU
- *
- */
-void __ref highbank_cpu_die(unsigned int cpu)
-{
-	highbank_set_cpu_jump(cpu, phys_to_virt(0));
-
-	flush_cache_louis();
-	highbank_set_core_pwr();
-
-	while (1)
-		cpu_do_idle();
-}

arch/arm/mach-highbank/platsmp.c

-/*
- * Copyright 2010-2011 Calxeda, Inc.
- * Based on platsmp.c, Copyright (C) 2002 ARM Ltd.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms and conditions of the GNU General Public License,
- * version 2, as published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
- * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program.  If not, see <http://www.gnu.org/licenses/>.
- */
-#include <linux/init.h>
-#include <linux/smp.h>
-#include <linux/io.h>
-
-#include <asm/smp_scu.h>
-
-#include "core.h"
-
-extern void secondary_startup(void);
-
-static int highbank_boot_secondary(unsigned int cpu, struct task_struct *idle)
-{
-	highbank_set_cpu_jump(cpu, secondary_startup);
-	arch_send_wakeup_ipi_mask(cpumask_of(cpu));
-	return 0;
-}
-
-/*
- * Initialise the CPU possible map early - this describes the CPUs
- * which may be present or become present in the system.
- */
-static void __init highbank_smp_init_cpus(void)
-{
-	unsigned int i, ncores = 4;
-
-	/* sanity check */
-	if (ncores > NR_CPUS) {
-		printk(KERN_WARNING
-		       "highbank: no. of cores (%d) greater than configured "
-		       "maximum of %d - clipping\n",
-		       ncores, NR_CPUS);
-		ncores = NR_CPUS;
-	}
-
-	for (i = 0; i < ncores; i++)
-		set_cpu_possible(i, true);
-}
-
-static void __init highbank_smp_prepare_cpus(unsigned int max_cpus)
-{
-	if (scu_base_addr)
-		scu_enable(scu_base_addr);
-}
-
-struct smp_operations highbank_smp_ops __initdata = {
-	.smp_init_cpus		= highbank_smp_init_cpus,
-	.smp_prepare_cpus	= highbank_smp_prepare_cpus,
-	.smp_boot_secondary	= highbank_boot_secondary,
-#ifdef CONFIG_HOTPLUG_CPU
-	.cpu_die		= highbank_cpu_die,
-#endif
-};

arch/arm/mach-highbank/pm.c

@@ -16,27 +16,19 @@
 
 #include <linux/cpu_pm.h>
 #include <linux/init.h>
-#include <linux/io.h>
 #include <linux/suspend.h>
 
-#include <asm/cacheflush.h>
-#include <asm/proc-fns.h>
 #include <asm/suspend.h>
-
-#include "core.h"
-#include "sysregs.h"
+#include <asm/psci.h>
 
 static int highbank_suspend_finish(unsigned long val)
 {
-	outer_flush_all();
-	outer_disable();
-
-	highbank_set_pwr_suspend();
-
-	cpu_do_idle();
+	const struct psci_power_state ps = {
+		.type = PSCI_POWER_STATE_TYPE_POWER_DOWN,
+		.affinity_level = 1,
+	};
 
-	highbank_clear_pwr_request();
-	return 0;
+	return psci_ops.cpu_suspend(ps, __pa(cpu_resume));
 }
 
 static int highbank_pm_enter(suspend_state_t state)
@@ -44,15 +36,11 @@ static int highbank_pm_enter(suspend_state_t state)
 	cpu_pm_enter();
 	cpu_cluster_pm_enter();
 
-	highbank_set_cpu_jump(0, cpu_resume);
 	cpu_suspend(0, highbank_suspend_finish);
 
 	cpu_cluster_pm_exit();
 	cpu_pm_exit();
 
-	highbank_smc1(0x102, 0x1);
-	if (scu_base_addr)
-		scu_enable(scu_base_addr);
 	return 0;
 }
 
@@ -63,5 +51,8 @@ static const struct platform_suspend_ops highbank_pm_ops = {
 
 void __init highbank_pm_init(void)
 {
+	if (!psci_ops.cpu_suspend)
+		return;
+
 	suspend_set_ops(&highbank_pm_ops);
 }

arch/arm/mach-imx/Kconfig

@@ -11,6 +11,7 @@ config ARCH_MXC
 	select GENERIC_IRQ_CHIP
 	select MIGHT_HAVE_CACHE_L2X0 if ARCH_MULTI_V6_V7
 	select MULTI_IRQ_HANDLER
+	select SOC_BUS
 	select SPARSE_IRQ
 	select USE_OF
 	help
@@ -24,7 +25,7 @@ config MXC_IRQ_PRIOR
 	help
 	  Select this if you want to use prioritized IRQ handling.
 	  This feature prevents higher priority ISR to be interrupted
-	  by lower priority IRQ even IRQF_DISABLED flag is not set.
+	  by lower priority IRQ.
 	  This may be useful in embedded applications, where are strong
 	  requirements for timing.
 	  Say N here, unless you have a specialized requirement.
@@ -793,6 +794,8 @@ config SOC_IMX6Q
 	select HAVE_IMX_SRC
 	select HAVE_SMP
 	select MFD_SYSCON
+	select MIGHT_HAVE_PCI
+	select PCI_DOMAINS if PCI
 	select PINCTRL
 	select PINCTRL_IMX6Q
 	select PL310_ERRATA_588369 if CACHE_PL310

arch/arm/mach-imx/Makefile

@@ -102,6 +102,8 @@ obj-$(CONFIG_SOC_IMX6SL) += clk-imx6sl.o mach-imx6sl.o
 
 ifeq ($(CONFIG_PM),y)
 obj-$(CONFIG_SOC_IMX6Q) += pm-imx6q.o headsmp.o
+# i.MX6SL reuses pm-imx6q.c
+obj-$(CONFIG_SOC_IMX6SL) += pm-imx6q.o
 endif
 
 # i.MX5 based machines

arch/arm/mach-imx/anatop.c

@@ -16,6 +16,7 @@
 #include <linux/mfd/syscon.h>
 #include <linux/regmap.h>
 #include "common.h"
+#include "hardware.h"
 
 #define REG_SET		0x4
 #define REG_CLR		0x8
@@ -26,6 +27,7 @@
 #define ANADIG_USB1_CHRG_DETECT	0x1b0
 #define ANADIG_USB2_CHRG_DETECT	0x210
 #define ANADIG_DIGPROG		0x260
+#define ANADIG_DIGPROG_IMX6SL	0x280
 
 #define BM_ANADIG_REG_2P5_ENABLE_WEAK_LINREG	0x40000
 #define BM_ANADIG_REG_CORE_FET_ODRIVE		0x20000000
@@ -76,21 +78,38 @@ static void imx_anatop_usb_chrg_detect_disable(void)
 		BM_ANADIG_USB_CHRG_DETECT_CHK_CHRG_B);
 }
 
-u32 imx_anatop_get_digprog(void)
+void __init imx_init_revision_from_anatop(void)
 {
 	struct device_node *np;
 	void __iomem *anatop_base;
-	static u32 digprog;
-
-	if (digprog)
-		return digprog;
+	unsigned int revision;
+	u32 digprog;
+	u16 offset = ANADIG_DIGPROG;
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-anatop");
 	anatop_base = of_iomap(np, 0);
 	WARN_ON(!anatop_base);
-	digprog = readl_relaxed(anatop_base + ANADIG_DIGPROG);
+	if (of_device_is_compatible(np, "fsl,imx6sl-anatop"))
+		offset = ANADIG_DIGPROG_IMX6SL;
+	digprog = readl_relaxed(anatop_base + offset);
+	iounmap(anatop_base);
+
+	switch (digprog & 0xff) {
+	case 0:
+		revision = IMX_CHIP_REVISION_1_0;
+		break;
+	case 1:
+		revision = IMX_CHIP_REVISION_1_1;
+		break;
+	case 2:
+		revision = IMX_CHIP_REVISION_1_2;
+		break;
+	default:
+		revision = IMX_CHIP_REVISION_UNKNOWN;
+	}
 
-	return digprog;
+	mxc_set_cpu_type(digprog >> 16 & 0xff);
+	imx_set_soc_revision(revision);
 }
 
 void __init imx_anatop_init(void)

arch/arm/mach-imx/clk-imx51-imx53.c

@@ -14,6 +14,9 @@
 #include <linux/clk-provider.h>
 #include <linux/of.h>
 #include <linux/err.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
 
 #include "crm-regs-imx5.h"
 #include "clk.h"
@@ -472,8 +475,9 @@ CLK_OF_DECLARE(imx51_ccm, "fsl,imx51-ccm", mx51_clocks_init_dt);
 
 static void __init mx53_clocks_init(struct device_node *np)
 {
-	int i;
+	int i, irq;
 	unsigned long r;
+	void __iomem *base;
 
 	clk[pll1_sw] = imx_clk_pllv2("pll1_sw", "osc", MX53_DPLL1_BASE);
 	clk[pll2_sw] = imx_clk_pllv2("pll2_sw", "osc", MX53_DPLL2_BASE);
@@ -559,14 +563,17 @@ static void __init mx53_clocks_init(struct device_node *np)
 	clk_set_rate(clk[esdhc_a_podf], 200000000);
 	clk_set_rate(clk[esdhc_b_podf], 200000000);
 
-	/* System timer */
-	mxc_timer_init(MX53_IO_ADDRESS(MX53_GPT1_BASE_ADDR), MX53_INT_GPT);
-
 	clk_prepare_enable(clk[iim_gate]);
 	imx_print_silicon_rev("i.MX53", mx53_revision());
 	clk_disable_unprepare(clk[iim_gate]);
 
 	r = clk_round_rate(clk[usboh3_per_gate], 54000000);
 	clk_set_rate(clk[usboh3_per_gate], r);
+
+	np = of_find_compatible_node(NULL, NULL, "fsl,imx53-gpt");
+	base = of_iomap(np, 0);
+	WARN_ON(!base);
+	irq = irq_of_parse_and_map(np, 0);
+	mxc_timer_init(base, irq);
 }
 CLK_OF_DECLARE(imx53_ccm, "fsl,imx53-ccm", mx53_clocks_init);

arch/arm/mach-imx/clk-imx6sl.c

@@ -127,6 +127,9 @@ static void __init imx6sl_clocks_init(struct device_node *ccm_node)
 	base = of_iomap(np, 0);
 	WARN_ON(!base);
 
+	/* Reuse imx6q pm code */
+	imx6q_pm_set_ccm_base(base);
+
 	/*                                              name                reg       shift width parent_names     num_parents */
 	clks[IMX6SL_CLK_STEP]             = imx_clk_mux("step",             base + 0xc,  8,  1, step_sels,         ARRAY_SIZE(step_sels));
 	clks[IMX6SL_CLK_PLL1_SW]          = imx_clk_mux("pll1_sw",          base + 0xc,  2,  1, pll1_sw_sels,      ARRAY_SIZE(pll1_sw_sels));

arch/arm/mach-imx/common.h

@@ -13,70 +13,73 @@
 
 #include <linux/reboot.h>
 
+struct irq_data;
 struct platform_device;
 struct pt_regs;
 struct clk;
 enum mxc_cpu_pwr_mode;
 
-extern void mx1_map_io(void);
-extern void mx21_map_io(void);
-extern void mx25_map_io(void);
-extern void mx27_map_io(void);
-extern void mx31_map_io(void);
-extern void mx35_map_io(void);
-extern void mx51_map_io(void);
-extern void mx53_map_io(void);
-extern void imx1_init_early(void);
-extern void imx21_init_early(void);
-extern void imx25_init_early(void);
-extern void imx27_init_early(void);
-extern void imx31_init_early(void);
-extern void imx35_init_early(void);
-extern void imx51_init_early(void);
-extern void imx53_init_early(void);
-extern void mxc_init_irq(void __iomem *);
-extern void tzic_init_irq(void __iomem *);
-extern void mx1_init_irq(void);
-extern void mx21_init_irq(void);
-extern void mx25_init_irq(void);
-extern void mx27_init_irq(void);
-extern void mx31_init_irq(void);
-extern void mx35_init_irq(void);
-extern void mx51_init_irq(void);
-extern void mx53_init_irq(void);
-extern void imx1_soc_init(void);
-extern void imx21_soc_init(void);
-extern void imx25_soc_init(void);
-extern void imx27_soc_init(void);
-extern void imx31_soc_init(void);
-extern void imx35_soc_init(void);
-extern void imx51_soc_init(void);
-extern void imx51_init_late(void);
-extern void imx53_init_late(void);
-extern void epit_timer_init(void __iomem *base, int irq);
-extern void mxc_timer_init(void __iomem *, int);
-extern int mx1_clocks_init(unsigned long fref);
-extern int mx21_clocks_init(unsigned long lref, unsigned long fref);
-extern int mx25_clocks_init(void);
-extern int mx27_clocks_init(unsigned long fref);
-extern int mx31_clocks_init(unsigned long fref);
-extern int mx35_clocks_init(void);
-extern int mx51_clocks_init(unsigned long ckil, unsigned long osc,
+void mx1_map_io(void);
+void mx21_map_io(void);
+void mx25_map_io(void);
+void mx27_map_io(void);
+void mx31_map_io(void);
+void mx35_map_io(void);
+void mx51_map_io(void);
+void mx53_map_io(void);
+void imx1_init_early(void);
+void imx21_init_early(void);
+void imx25_init_early(void);
+void imx27_init_early(void);
+void imx31_init_early(void);
+void imx35_init_early(void);
+void imx51_init_early(void);
+void imx53_init_early(void);
+void mxc_init_irq(void __iomem *);
+void tzic_init_irq(void __iomem *);
+void mx1_init_irq(void);
+void mx21_init_irq(void);
+void mx25_init_irq(void);
+void mx27_init_irq(void);
+void mx31_init_irq(void);
+void mx35_init_irq(void);
+void mx51_init_irq(void);
+void mx53_init_irq(void);
+void imx1_soc_init(void);
+void imx21_soc_init(void);
+void imx25_soc_init(void);
+void imx27_soc_init(void);
+void imx31_soc_init(void);
+void imx35_soc_init(void);
+void imx51_soc_init(void);
+void imx51_init_late(void);
+void imx53_init_late(void);
+void epit_timer_init(void __iomem *base, int irq);
+void mxc_timer_init(void __iomem *, int);
+int mx1_clocks_init(unsigned long fref);
+int mx21_clocks_init(unsigned long lref, unsigned long fref);
+int mx25_clocks_init(void);
+int mx27_clocks_init(unsigned long fref);
+int mx31_clocks_init(unsigned long fref);
+int mx35_clocks_init(void);
+int mx51_clocks_init(unsigned long ckil, unsigned long osc,
 			unsigned long ckih1, unsigned long ckih2);
-extern int mx25_clocks_init_dt(void);
-extern int mx27_clocks_init_dt(void);
-extern int mx31_clocks_init_dt(void);
-extern struct platform_device *mxc_register_gpio(char *name, int id,
+int mx25_clocks_init_dt(void);
+int mx27_clocks_init_dt(void);
+int mx31_clocks_init_dt(void);
+struct platform_device *mxc_register_gpio(char *name, int id,
 	resource_size_t iobase, resource_size_t iosize, int irq, int irq_high);
-extern void mxc_set_cpu_type(unsigned int type);
-extern void mxc_restart(enum reboot_mode, const char *);
-extern void mxc_arch_reset_init(void __iomem *);
-extern void mxc_arch_reset_init_dt(void);
-extern int mx53_revision(void);
-extern int imx6q_revision(void);
-extern int mx53_display_revision(void);
-extern void imx_set_aips(void __iomem *);
-extern int mxc_device_init(void);
+void mxc_set_cpu_type(unsigned int type);
+void mxc_restart(enum reboot_mode, const char *);
+void mxc_arch_reset_init(void __iomem *);
+void mxc_arch_reset_init_dt(void);
+int mx53_revision(void);
+void imx_set_aips(void __iomem *);
+int mxc_device_init(void);
+void imx_set_soc_revision(unsigned int rev);
+unsigned int imx_get_soc_revision(void);
+void imx_init_revision_from_anatop(void);
+struct device *imx_soc_device_init(void);
 
 enum mxc_cpu_pwr_mode {
 	WAIT_CLOCKED,		/* wfi only */
@@ -93,8 +96,8 @@ enum mx3_cpu_pwr_mode {
 	MX3_SLEEP,
 };
 
-extern void mx3_cpu_lp_set(enum mx3_cpu_pwr_mode mode);
-extern void imx_print_silicon_rev(const char *cpu, int srev);
+void mx3_cpu_lp_set(enum mx3_cpu_pwr_mode mode);
+void imx_print_silicon_rev(const char *cpu, int srev);
 
 void avic_handle_irq(struct pt_regs *);
 void tzic_handle_irq(struct pt_regs *);
@@ -108,54 +111,61 @@ void tzic_handle_irq(struct pt_regs *);
 #define imx51_handle_irq tzic_handle_irq
 #define imx53_handle_irq tzic_handle_irq
 
-extern void imx_enable_cpu(int cpu, bool enable);
-extern void imx_set_cpu_jump(int cpu, void *jump_addr);
-extern u32 imx_get_cpu_arg(int cpu);
-extern void imx_set_cpu_arg(int cpu, u32 arg);
-extern void v7_cpu_resume(void);
+void imx_enable_cpu(int cpu, bool enable);
+void imx_set_cpu_jump(int cpu, void *jump_addr);
+u32 imx_get_cpu_arg(int cpu);
+void imx_set_cpu_arg(int cpu, u32 arg);
+void v7_cpu_resume(void);
 #ifdef CONFIG_SMP
-extern void v7_secondary_startup(void);
-extern void imx_scu_map_io(void);
-extern void imx_smp_prepare(void);
-extern void imx_scu_standby_enable(void);
+void v7_secondary_startup(void);
+void imx_scu_map_io(void);
+void imx_smp_prepare(void);
+void imx_scu_standby_enable(void);
 #else
 static inline void imx_scu_map_io(void) {}
 static inline void imx_smp_prepare(void) {}
 static inline void imx_scu_standby_enable(void) {}
 #endif
-extern void imx_src_init(void);
-extern void imx_src_prepare_restart(void);
-extern void imx_gpc_init(void);
-extern void imx_gpc_pre_suspend(void);
-extern void imx_gpc_post_resume(void);
-extern void imx_gpc_mask_all(void);
-extern void imx_gpc_restore_all(void);
-extern void imx_anatop_init(void);
-extern void imx_anatop_pre_suspend(void);
-extern void imx_anatop_post_resume(void);
-extern u32 imx_anatop_get_digprog(void);
-extern int imx6q_set_lpm(enum mxc_cpu_pwr_mode mode);
-extern void imx6q_set_chicken_bit(void);
-
-extern void imx_cpu_die(unsigned int cpu);
-extern int imx_cpu_kill(unsigned int cpu);
+void imx_src_init(void);
+#ifdef CONFIG_HAVE_IMX_SRC
+void imx_src_prepare_restart(void);
+#else
+static inline void imx_src_prepare_restart(void) {}
+#endif
+void imx_gpc_init(void);
+void imx_gpc_pre_suspend(void);
+void imx_gpc_post_resume(void);
+void imx_gpc_mask_all(void);
+void imx_gpc_restore_all(void);
+void imx_gpc_irq_mask(struct irq_data *d);
+void imx_gpc_irq_unmask(struct irq_data *d);
+void imx_anatop_init(void);
+void imx_anatop_pre_suspend(void);
+void imx_anatop_post_resume(void);
+int imx6q_set_lpm(enum mxc_cpu_pwr_mode mode);
+void imx6q_set_chicken_bit(void);
+
+void imx_cpu_die(unsigned int cpu);
+int imx_cpu_kill(unsigned int cpu);
 
 #ifdef CONFIG_PM
-extern void imx6q_pm_init(void);
-extern void imx5_pm_init(void);
+void imx6q_pm_init(void);
+void imx6q_pm_set_ccm_base(void __iomem *base);
+void imx5_pm_init(void);
 #else
 static inline void imx6q_pm_init(void) {}
+static inline void imx6q_pm_set_ccm_base(void __iomem *base) {}
 static inline void imx5_pm_init(void) {}
 #endif
 
 #ifdef CONFIG_NEON
-extern int mx51_neon_fixup(void);
+int mx51_neon_fixup(void);
 #else
 static inline int mx51_neon_fixup(void) { return 0; }
 #endif
 
 #ifdef CONFIG_CACHE_L2X0
-extern void imx_init_l2cache(void);
+void imx_init_l2cache(void);
 #else
 static inline void imx_init_l2cache(void) {}
 #endif

arch/arm/mach-imx/cpu.c

-
+#include <linux/err.h>
 #include <linux/module.h>
 #include <linux/io.h>
+#include <linux/of.h>
+#include <linux/slab.h>
+#include <linux/sys_soc.h>
 
 #include "hardware.h"
 #include "common.h"
@@ -8,11 +11,23 @@
 unsigned int __mxc_cpu_type;
 EXPORT_SYMBOL(__mxc_cpu_type);
 
+static unsigned int imx_soc_revision;
+
 void mxc_set_cpu_type(unsigned int type)
 {
 	__mxc_cpu_type = type;
 }
 
+void imx_set_soc_revision(unsigned int rev)
+{
+	imx_soc_revision = rev;
+}
+
+unsigned int imx_get_soc_revision(void)
+{
+	return imx_soc_revision;
+}
+
 void imx_print_silicon_rev(const char *cpu, int srev)
 {
 	if (srev == IMX_CHIP_REVISION_UNKNOWN)
@@ -44,3 +59,81 @@ void __init imx_set_aips(void __iomem *base)
 	reg = __raw_readl(base + 0x50) & 0x00FFFFFF;
 	__raw_writel(reg, base + 0x50);
 }
+
+struct device * __init imx_soc_device_init(void)
+{
+	struct soc_device_attribute *soc_dev_attr;
+	struct soc_device *soc_dev;
+	struct device_node *root;
+	const char *soc_id;
+	int ret;
+
+	soc_dev_attr = kzalloc(sizeof(*soc_dev_attr), GFP_KERNEL);
+	if (!soc_dev_attr)
+		return NULL;
+
+	soc_dev_attr->family = "Freescale i.MX";
+
+	root = of_find_node_by_path("/");
+	ret = of_property_read_string(root, "model", &soc_dev_attr->machine);
+	of_node_put(root);
+	if (ret)
+		goto free_soc;
+
+	switch (__mxc_cpu_type) {
+	case MXC_CPU_MX1:
+		soc_id = "i.MX1";
+		break;
+	case MXC_CPU_MX21:
+		soc_id = "i.MX21";
+		break;
+	case MXC_CPU_MX25:
+		soc_id = "i.MX25";
+		break;
+	case MXC_CPU_MX27:
+		soc_id = "i.MX27";
+		break;
+	case MXC_CPU_MX31:
+		soc_id = "i.MX31";
+		break;
+	case MXC_CPU_MX35:
+		soc_id = "i.MX35";
+		break;
+	case MXC_CPU_MX51:
+		soc_id = "i.MX51";
+		break;
+	case MXC_CPU_MX53:
+		soc_id = "i.MX53";
+		break;
+	case MXC_CPU_IMX6SL:
+		soc_id = "i.MX6SL";
+		break;
+	case MXC_CPU_IMX6DL:
+		soc_id = "i.MX6DL";
+		break;
+	case MXC_CPU_IMX6Q:
+		soc_id = "i.MX6Q";
+		break;
+	default:
+		soc_id = "Unknown";
+	}
+	soc_dev_attr->soc_id = soc_id;
+
+	soc_dev_attr->revision = kasprintf(GFP_KERNEL, "%d.%d",
+					   (imx_soc_revision >> 4) & 0xf,
+					   imx_soc_revision & 0xf);
+	if (!soc_dev_attr->revision)
+		goto free_soc;
+
+	soc_dev = soc_device_register(soc_dev_attr);
+	if (IS_ERR(soc_dev))
+		goto free_rev;
+
+	return soc_device_to_device(soc_dev);
+
+free_rev:
+	kfree(soc_dev_attr->revision);
+free_soc:
+	kfree(soc_dev_attr);
+	return NULL;
+}

arch/arm/mach-imx/epit.c

@@ -171,7 +171,7 @@ static irqreturn_t epit_timer_interrupt(int irq, void *dev_id)
 
 static struct irqaction epit_timer_irq = {
 	.name		= "i.MX EPIT Timer Tick",
-	.flags		= IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
+	.flags		= IRQF_TIMER | IRQF_IRQPOLL,
 	.handler	= epit_timer_interrupt,
 };
 

arch/arm/mach-imx/gpc.c

@@ -90,7 +90,7 @@ void imx_gpc_restore_all(void)
 		writel_relaxed(gpc_saved_imrs[i], reg_imr1 + i * 4);
 }
 
-static void imx_gpc_irq_unmask(struct irq_data *d)
+void imx_gpc_irq_unmask(struct irq_data *d)
 {
 	void __iomem *reg;
 	u32 val;
@@ -105,7 +105,7 @@ static void imx_gpc_irq_unmask(struct irq_data *d)
 	writel_relaxed(val, reg);
 }
 
-static void imx_gpc_irq_mask(struct irq_data *d)
+void imx_gpc_irq_mask(struct irq_data *d)
 {
 	void __iomem *reg;
 	u32 val;

arch/arm/mach-imx/hotplug.c

@@ -52,6 +52,8 @@ void imx_cpu_die(unsigned int cpu)
 	 * the register being cleared to kill the cpu.
 	 */
 	imx_set_cpu_arg(cpu, ~0);
+
+	while (1)
 		cpu_do_idle();
 }
 

arch/arm/mach-imx/mach-armadillo5x0.c

@@ -404,8 +404,7 @@ static int armadillo5x0_sdhc1_init(struct device *dev,
 
 	/* When supported the trigger type have to be BOTH */
 	ret = request_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_ATA_DMACK)),
-			  detect_irq,
-			  IRQF_DISABLED | IRQF_TRIGGER_FALLING,
+			  detect_irq, IRQF_TRIGGER_FALLING,
 			  "sdhc-detect", data);
 
 	if (ret)

arch/arm/mach-imx/mach-imx6q.c

@@ -13,7 +13,6 @@
 #include <linux/clk.h>
 #include <linux/clkdev.h>
 #include <linux/cpu.h>
-#include <linux/delay.h>
 #include <linux/export.h>
 #include <linux/init.h>
 #include <linux/io.h>
@@ -38,64 +37,6 @@
 #include "cpuidle.h"
 #include "hardware.h"
 
-static u32 chip_revision;
-
-int imx6q_revision(void)
-{
-	return chip_revision;
-}
-
-static void __init imx6q_init_revision(void)
-{
-	u32 rev = imx_anatop_get_digprog();
-
-	switch (rev & 0xff) {
-	case 0:
-		chip_revision = IMX_CHIP_REVISION_1_0;
-		break;
-	case 1:
-		chip_revision = IMX_CHIP_REVISION_1_1;
-		break;
-	case 2:
-		chip_revision = IMX_CHIP_REVISION_1_2;
-		break;
-	default:
-		chip_revision = IMX_CHIP_REVISION_UNKNOWN;
-	}
-
-	mxc_set_cpu_type(rev >> 16 & 0xff);
-}
-
-static void imx6q_restart(enum reboot_mode mode, const char *cmd)
-{
-	struct device_node *np;
-	void __iomem *wdog_base;
-
-	np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-wdt");
-	wdog_base = of_iomap(np, 0);
-	if (!wdog_base)
-		goto soft;
-
-	imx_src_prepare_restart();
-
-	/* enable wdog */
-	writew_relaxed(1 << 2, wdog_base);
-	/* write twice to ensure the request will not get ignored */
-	writew_relaxed(1 << 2, wdog_base);
-
-	/* wait for reset to assert ... */
-	mdelay(500);
-
-	pr_err("Watchdog reset failed to assert reset\n");
-
-	/* delay to allow the serial port to show the message */
-	mdelay(50);
-
-soft:
-	/* we'll take a jump through zero as a poor second */
-	soft_restart(0);
-}
-
 /* For imx6q sabrelite board: set KSZ9021RN RGMII pad skew */
 static int ksz9021rn_phy_fixup(struct phy_device *phydev)
 {
@@ -190,12 +131,20 @@ static void __init imx6q_1588_init(void)
 
 static void __init imx6q_init_machine(void)
 {
+	struct device *parent;
+
 	imx_print_silicon_rev(cpu_is_imx6dl() ? "i.MX6DL" : "i.MX6Q",
-			      imx6q_revision());
+			      imx_get_soc_revision());
+
+	mxc_arch_reset_init_dt();
+
+	parent = imx_soc_device_init();
+	if (parent == NULL)
+		pr_warn("failed to initialize soc device\n");
 
 	imx6q_enet_phy_init();
 
-	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
+	of_platform_populate(NULL, of_default_bus_match_table, NULL, parent);
 
 	imx_anatop_init();
 	imx6q_pm_init();
@@ -270,7 +219,7 @@ static void __init imx6q_init_late(void)
 	 * WAIT mode is broken on TO 1.0 and 1.1, so there is no point
 	 * to run cpuidle on them.
 	 */
-	if (imx6q_revision() > IMX_CHIP_REVISION_1_1)
+	if (imx_get_soc_revision() > IMX_CHIP_REVISION_1_1)
 		imx6q_cpuidle_init();
 
 	if (IS_ENABLED(CONFIG_ARM_IMX6Q_CPUFREQ)) {
@@ -287,7 +236,7 @@ static void __init imx6q_map_io(void)
 
 static void __init imx6q_init_irq(void)
 {
-	imx6q_init_revision();
+	imx_init_revision_from_anatop();
 	imx_init_l2cache();
 	imx_src_init();
 	imx_gpc_init();
@@ -307,5 +256,5 @@ DT_MACHINE_START(IMX6Q, "Freescale i.MX6 Quad/DualLite (Device Tree)")
 	.init_machine	= imx6q_init_machine,
 	.init_late      = imx6q_init_late,
 	.dt_compat	= imx6q_dt_compat,
-	.restart	= imx6q_restart,
+	.restart	= mxc_restart,
 MACHINE_END

arch/arm/mach-imx/mach-imx6sl.c

@@ -10,20 +10,51 @@
 #include <linux/irqchip.h>
 #include <linux/of.h>
 #include <linux/of_platform.h>
+#include <linux/mfd/syscon.h>
+#include <linux/mfd/syscon/imx6q-iomuxc-gpr.h>
+#include <linux/regmap.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
 #include "common.h"
 
+static void __init imx6sl_fec_init(void)
+{
+	struct regmap *gpr;
+
+	/* set FEC clock from internal PLL clock source */
+	gpr = syscon_regmap_lookup_by_compatible("fsl,imx6sl-iomuxc-gpr");
+	if (!IS_ERR(gpr)) {
+		regmap_update_bits(gpr, IOMUXC_GPR1,
+			IMX6SL_GPR1_FEC_CLOCK_MUX2_SEL_MASK, 0);
+		regmap_update_bits(gpr, IOMUXC_GPR1,
+			IMX6SL_GPR1_FEC_CLOCK_MUX1_SEL_MASK, 0);
+	} else {
+		pr_err("failed to find fsl,imx6sl-iomux-gpr regmap\n");
+	}
+}
+
 static void __init imx6sl_init_machine(void)
 {
+	struct device *parent;
+
 	mxc_arch_reset_init_dt();
 
-	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
+	parent = imx_soc_device_init();
+	if (parent == NULL)
+		pr_warn("failed to initialize soc device\n");
+
+	of_platform_populate(NULL, of_default_bus_match_table, NULL, parent);
+
+	imx6sl_fec_init();
+	imx_anatop_init();
+	/* Reuse imx6q pm code */
+	imx6q_pm_init();
 }
 
 static void __init imx6sl_init_irq(void)
 {
+	imx_init_revision_from_anatop();
 	imx_init_l2cache();
 	imx_src_init();
 	imx_gpc_init();

arch/arm/mach-imx/mach-mx31_3ds.c

@@ -311,7 +311,7 @@ static int mx31_3ds_sdhc1_init(struct device *dev,
 	}
 
 	ret = request_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1)),
-			  detect_irq, IRQF_DISABLED |
+			  detect_irq,
 			  IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
 			  "sdhc1-detect", data);
 	if (ret) {

arch/arm/mach-imx/mach-pcm037.c

@@ -371,8 +371,7 @@ static int pcm970_sdhc1_init(struct device *dev, irq_handler_t detect_irq,
 #endif
 
 	ret = request_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_SCK6)), detect_irq,
-			IRQF_DISABLED | IRQF_TRIGGER_FALLING,
-				"sdhc-detect", data);
+			IRQF_TRIGGER_FALLING, "sdhc-detect", data);
 	if (ret)
 		goto err_gpio_free_2;
 

arch/arm/mach-imx/mm-imx5.c

@@ -15,6 +15,7 @@
 #include <linux/init.h>
 #include <linux/clk.h>
 #include <linux/pinctrl/machine.h>
+#include <linux/of_address.h>
 
 #include <asm/mach/map.h>
 
@@ -88,8 +89,15 @@ void __init imx51_init_early(void)
 
 void __init imx53_init_early(void)
 {
+	struct device_node *np;
+	void __iomem *base;
+
 	mxc_set_cpu_type(MXC_CPU_MX53);
-	mxc_iomux_v3_init(MX53_IO_ADDRESS(MX53_IOMUXC_BASE_ADDR));
+
+	np = of_find_compatible_node(NULL, NULL, "fsl,imx53-iomuxc");
+	base = of_iomap(np, 0);
+	WARN_ON(!base);
+	mxc_iomux_v3_init(base);
 	imx_src_init();
 }
 
@@ -100,7 +108,14 @@ void __init mx51_init_irq(void)
 
 void __init mx53_init_irq(void)
 {
-	tzic_init_irq(MX53_IO_ADDRESS(MX53_TZIC_BASE_ADDR));
+	struct device_node *np;
+	void __iomem *base;
+
+	np = of_find_compatible_node(NULL, NULL, "fsl,imx53-tzic");
+	base = of_iomap(np, 0);
+	WARN_ON(!base);
+
+	tzic_init_irq(base);
 }
 
 static struct sdma_platform_data imx51_sdma_pdata __initdata = {

arch/arm/mach-imx/mx31lilly-db.c

@@ -130,8 +130,7 @@ static int mxc_mmc1_init(struct device *dev,
 	gpio_direction_input(gpio_wp);
 
 	ret = request_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1)),
-			  detect_irq,
-			  IRQF_DISABLED | IRQF_TRIGGER_FALLING,
+			  detect_irq, IRQF_TRIGGER_FALLING,
 			  "MMC detect", data);
 	if (ret)
 		goto exit_free_wp;

arch/arm/mach-imx/mxc.h

@@ -34,6 +34,7 @@
 #define MXC_CPU_MX35		35
 #define MXC_CPU_MX51		51
 #define MXC_CPU_MX53		53
+#define MXC_CPU_IMX6SL		0x60
 #define MXC_CPU_IMX6DL		0x61
 #define MXC_CPU_IMX6Q		0x63
 
@@ -152,6 +153,11 @@ extern unsigned int __mxc_cpu_type;
 #endif
 
 #ifndef __ASSEMBLY__
+static inline bool cpu_is_imx6sl(void)
+{
+	return __mxc_cpu_type == MXC_CPU_IMX6SL;
+}
+
 static inline bool cpu_is_imx6dl(void)
 {
 	return __mxc_cpu_type == MXC_CPU_IMX6DL;

arch/arm/mach-imx/pm-imx6q.c

@@ -10,9 +10,15 @@
  * http://www.gnu.org/copyleft/gpl.html
  */
 
+#include <linux/delay.h>
 #include <linux/init.h>
 #include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/mfd/syscon.h>
+#include <linux/mfd/syscon/imx6q-iomuxc-gpr.h>
 #include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/regmap.h>
 #include <linux/suspend.h>
 #include <asm/cacheflush.h>
 #include <asm/proc-fns.h>
@@ -22,6 +28,147 @@
 #include "common.h"
 #include "hardware.h"
 
+#define CCR				0x0
+#define BM_CCR_WB_COUNT			(0x7 << 16)
+#define BM_CCR_RBC_BYPASS_COUNT		(0x3f << 21)
+#define BM_CCR_RBC_EN			(0x1 << 27)
+
+#define CLPCR				0x54
+#define BP_CLPCR_LPM			0
+#define BM_CLPCR_LPM			(0x3 << 0)
+#define BM_CLPCR_BYPASS_PMIC_READY	(0x1 << 2)
+#define BM_CLPCR_ARM_CLK_DIS_ON_LPM	(0x1 << 5)
+#define BM_CLPCR_SBYOS			(0x1 << 6)
+#define BM_CLPCR_DIS_REF_OSC		(0x1 << 7)
+#define BM_CLPCR_VSTBY			(0x1 << 8)
+#define BP_CLPCR_STBY_COUNT		9
+#define BM_CLPCR_STBY_COUNT		(0x3 << 9)
+#define BM_CLPCR_COSC_PWRDOWN		(0x1 << 11)
+#define BM_CLPCR_WB_PER_AT_LPM		(0x1 << 16)
+#define BM_CLPCR_WB_CORE_AT_LPM		(0x1 << 17)
+#define BM_CLPCR_BYP_MMDC_CH0_LPM_HS	(0x1 << 19)
+#define BM_CLPCR_BYP_MMDC_CH1_LPM_HS	(0x1 << 21)
+#define BM_CLPCR_MASK_CORE0_WFI		(0x1 << 22)
+#define BM_CLPCR_MASK_CORE1_WFI		(0x1 << 23)
+#define BM_CLPCR_MASK_CORE2_WFI		(0x1 << 24)
+#define BM_CLPCR_MASK_CORE3_WFI		(0x1 << 25)
+#define BM_CLPCR_MASK_SCU_IDLE		(0x1 << 26)
+#define BM_CLPCR_MASK_L2CC_IDLE		(0x1 << 27)
+
+#define CGPR				0x64
+#define BM_CGPR_CHICKEN_BIT		(0x1 << 17)
+
+static void __iomem *ccm_base;
+
+void imx6q_set_chicken_bit(void)
+{
+	u32 val = readl_relaxed(ccm_base + CGPR);
+
+	val |= BM_CGPR_CHICKEN_BIT;
+	writel_relaxed(val, ccm_base + CGPR);
+}
+
+static void imx6q_enable_rbc(bool enable)
+{
+	u32 val;
+
+	/*
+	 * need to mask all interrupts in GPC before
+	 * operating RBC configurations
+	 */
+	imx_gpc_mask_all();
+
+	/* configure RBC enable bit */
+	val = readl_relaxed(ccm_base + CCR);
+	val &= ~BM_CCR_RBC_EN;
+	val |= enable ? BM_CCR_RBC_EN : 0;
+	writel_relaxed(val, ccm_base + CCR);
+
+	/* configure RBC count */
+	val = readl_relaxed(ccm_base + CCR);
+	val &= ~BM_CCR_RBC_BYPASS_COUNT;
+	val |= enable ? BM_CCR_RBC_BYPASS_COUNT : 0;
+	writel(val, ccm_base + CCR);
+
+	/*
+	 * need to delay at least 2 cycles of CKIL(32K)
+	 * due to hardware design requirement, which is
+	 * ~61us, here we use 65us for safe
+	 */
+	udelay(65);
+
+	/* restore GPC interrupt mask settings */
+	imx_gpc_restore_all();
+}
+
+static void imx6q_enable_wb(bool enable)
+{
+	u32 val;
+
+	/* configure well bias enable bit */
+	val = readl_relaxed(ccm_base + CLPCR);
+	val &= ~BM_CLPCR_WB_PER_AT_LPM;
+	val |= enable ? BM_CLPCR_WB_PER_AT_LPM : 0;
+	writel_relaxed(val, ccm_base + CLPCR);
+
+	/* configure well bias count */
+	val = readl_relaxed(ccm_base + CCR);
+	val &= ~BM_CCR_WB_COUNT;
+	val |= enable ? BM_CCR_WB_COUNT : 0;
+	writel_relaxed(val, ccm_base + CCR);
+}
+
+int imx6q_set_lpm(enum mxc_cpu_pwr_mode mode)
+{
+	struct irq_desc *iomuxc_irq_desc;
+	u32 val = readl_relaxed(ccm_base + CLPCR);
+
+	val &= ~BM_CLPCR_LPM;
+	switch (mode) {
+	case WAIT_CLOCKED:
+		break;
+	case WAIT_UNCLOCKED:
+		val |= 0x1 << BP_CLPCR_LPM;
+		val |= BM_CLPCR_ARM_CLK_DIS_ON_LPM;
+		break;
+	case STOP_POWER_ON:
+		val |= 0x2 << BP_CLPCR_LPM;
+		break;
+	case WAIT_UNCLOCKED_POWER_OFF:
+		val |= 0x1 << BP_CLPCR_LPM;
+		val &= ~BM_CLPCR_VSTBY;
+		val &= ~BM_CLPCR_SBYOS;
+		break;
+	case STOP_POWER_OFF:
+		val |= 0x2 << BP_CLPCR_LPM;
+		val |= 0x3 << BP_CLPCR_STBY_COUNT;
+		val |= BM_CLPCR_VSTBY;
+		val |= BM_CLPCR_SBYOS;
+		if (cpu_is_imx6sl()) {
+			val |= BM_CLPCR_BYPASS_PMIC_READY;
+			val |= BM_CLPCR_BYP_MMDC_CH0_LPM_HS;
+		} else {
+			val |= BM_CLPCR_BYP_MMDC_CH1_LPM_HS;
+		}
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	/*
+	 * Unmask the always pending IOMUXC interrupt #32 as wakeup source to
+	 * deassert dsm_request signal, so that we can ensure dsm_request
+	 * is not asserted when we're going to write CLPCR register to set LPM.
+	 * After setting up LPM bits, we need to mask this wakeup source.
+	 */
+	iomuxc_irq_desc = irq_to_desc(32);
+	imx_gpc_irq_unmask(&iomuxc_irq_desc->irq_data);
+	writel_relaxed(val, ccm_base + CLPCR);
+	imx_gpc_irq_mask(&iomuxc_irq_desc->irq_data);
+
+	return 0;
+}
+
 static int imx6q_suspend_finish(unsigned long val)
 {
 	cpu_do_idle();
@@ -33,14 +180,19 @@ static int imx6q_pm_enter(suspend_state_t state)
 	switch (state) {
 	case PM_SUSPEND_MEM:
 		imx6q_set_lpm(STOP_POWER_OFF);
+		imx6q_enable_wb(true);
+		imx6q_enable_rbc(true);
 		imx_gpc_pre_suspend();
 		imx_anatop_pre_suspend();
 		imx_set_cpu_jump(0, v7_cpu_resume);
 		/* Zzz ... */
 		cpu_suspend(0, imx6q_suspend_finish);
+		if (cpu_is_imx6q() || cpu_is_imx6dl())
 			imx_smp_prepare();
 		imx_anatop_post_resume();
 		imx_gpc_post_resume();
+		imx6q_enable_rbc(false);
+		imx6q_enable_wb(false);
 		imx6q_set_lpm(WAIT_CLOCKED);
 		break;
 	default:
@@ -55,7 +207,29 @@ static const struct platform_suspend_ops imx6q_pm_ops = {
 	.valid = suspend_valid_only_mem,
 };
 
+void __init imx6q_pm_set_ccm_base(void __iomem *base)
+{
+	ccm_base = base;
+}
+
 void __init imx6q_pm_init(void)
 {
+	struct regmap *gpr;
+
+	WARN_ON(!ccm_base);
+
+	/*
+	 * Force IOMUXC irq pending, so that the interrupt to GPC can be
+	 * used to deassert dsm_request signal when the signal gets
+	 * asserted unexpectedly.
+	 */
+	gpr = syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr");
+	if (!IS_ERR(gpr))
+		regmap_update_bits(gpr, IOMUXC_GPR1, IMX6Q_GPR1_GINT,
+				   IMX6Q_GPR1_GINT);
+
+	/* Set initial power mode */
+	imx6q_set_lpm(WAIT_CLOCKED);
+
 	suspend_set_ops(&imx6q_pm_ops);
 }

arch/arm/mach-imx/src.c

@@ -91,6 +91,7 @@ void imx_enable_cpu(int cpu, bool enable)
 	spin_lock(&scr_lock);
 	val = readl_relaxed(src_base + SRC_SCR);
 	val = enable ? val | mask : val & ~mask;
+	val |= 1 << (BP_SRC_SCR_CORE1_RST + cpu - 1);
 	writel_relaxed(val, src_base + SRC_SCR);
 	spin_unlock(&scr_lock);
 }

arch/arm/mach-imx/system.c

@@ -42,6 +42,9 @@ void mxc_restart(enum reboot_mode mode, const char *cmd)
 {
 	unsigned int wcr_enable;
 
+	if (cpu_is_imx6q() || cpu_is_imx6dl())
+		imx_src_prepare_restart();
+
 	if (wdog_clk)
 		clk_enable(wdog_clk);
 
@@ -52,6 +55,8 @@ void mxc_restart(enum reboot_mode mode, const char *cmd)
 
 	/* Assert SRS signal */
 	__raw_writew(wcr_enable, wdog_base);
+	/* write twice to ensure the request will not get ignored */
+	__raw_writew(wcr_enable, wdog_base);
 
 	/* wait for reset to assert... */
 	mdelay(500);

arch/arm/mach-imx/time.c

@@ -250,7 +250,7 @@ static irqreturn_t mxc_timer_interrupt(int irq, void *dev_id)
 
 static struct irqaction mxc_timer_irq = {
 	.name		= "i.MX Timer Tick",
-	.flags		= IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
+	.flags		= IRQF_TIMER | IRQF_IRQPOLL,
 	.handler	= mxc_timer_interrupt,
 };
 

arch/arm/mach-integrator/include/mach/cm.h → arch/arm/mach-integrator/cm.h

 /*
- * update the core module control register.
+ * access the core module control register.
  */
+u32 cm_get(void);
 void cm_control(u32, u32);
 
-#define CM_CTRL	__io_address(INTEGRATOR_HDR_CTRL)
+struct device_node;
+void cm_init(void);
+void cm_clear_irqs(void);
 
 #define CM_CTRL_LED			(1 << 0)
 #define CM_CTRL_nMBDET			(1 << 1)

arch/arm/mach-integrator/core.c

@@ -22,77 +22,30 @@
 #include <linux/amba/serial.h>
 #include <linux/io.h>
 #include <linux/stat.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
 
 #include <mach/hardware.h>
 #include <mach/platform.h>
-#include <mach/cm.h>
-#include <mach/irqs.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/time.h>
 #include <asm/pgtable.h>
 
+#include "cm.h"
 #include "common.h"
 
-#ifdef CONFIG_ATAGS
-
-#define INTEGRATOR_RTC_IRQ	{ IRQ_RTCINT }
-#define INTEGRATOR_UART0_IRQ	{ IRQ_UARTINT0 }
-#define INTEGRATOR_UART1_IRQ	{ IRQ_UARTINT1 }
-#define KMI0_IRQ		{ IRQ_KMIINT0 }
-#define KMI1_IRQ		{ IRQ_KMIINT1 }
-
-static AMBA_APB_DEVICE(rtc, "rtc", 0,
-	INTEGRATOR_RTC_BASE, INTEGRATOR_RTC_IRQ, NULL);
-
-static AMBA_APB_DEVICE(uart0, "uart0", 0,
-	INTEGRATOR_UART0_BASE, INTEGRATOR_UART0_IRQ, NULL);
-
-static AMBA_APB_DEVICE(uart1, "uart1", 0,
-	INTEGRATOR_UART1_BASE, INTEGRATOR_UART1_IRQ, NULL);
-
-static AMBA_APB_DEVICE(kmi0, "kmi0", 0, KMI0_BASE, KMI0_IRQ, NULL);
-static AMBA_APB_DEVICE(kmi1, "kmi1", 0, KMI1_BASE, KMI1_IRQ, NULL);
-
-static struct amba_device *amba_devs[] __initdata = {
-	&rtc_device,
-	&uart0_device,
-	&uart1_device,
-	&kmi0_device,
-	&kmi1_device,
-};
-
-int __init integrator_init(bool is_cp)
-{
-	int i;
+static DEFINE_RAW_SPINLOCK(cm_lock);
+static void __iomem *cm_base;
 
-	/*
-	 * The Integrator/AP lacks necessary AMBA PrimeCell IDs, so we need to
-	 * hard-code them. The Integator/CP and forward have proper cell IDs.
-	 * Else we leave them undefined to the bus driver can autoprobe them.
+/**
+ * cm_get - get the value from the CM_CTRL register
  */
-	if (!is_cp && IS_ENABLED(CONFIG_ARCH_INTEGRATOR_AP)) {
-		rtc_device.periphid	= 0x00041030;
-		uart0_device.periphid	= 0x00041010;
-		uart1_device.periphid	= 0x00041010;
-		kmi0_device.periphid	= 0x00041050;
-		kmi1_device.periphid	= 0x00041050;
-		uart0_device.dev.platform_data = &ap_uart_data;
-		uart1_device.dev.platform_data = &ap_uart_data;
-	}
-
-	for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
-		struct amba_device *d = amba_devs[i];
-		amba_device_register(d, &iomem_resource);
-	}
-
-	return 0;
+u32 cm_get(void)
+{
+	return readl(cm_base + INTEGRATOR_HDR_CTRL_OFFSET);
 }
 
-#endif
-
-static DEFINE_RAW_SPINLOCK(cm_lock);
-
 /**
  * cm_control - update the CM_CTRL register.
  * @mask: bits to change
@@ -104,12 +57,80 @@ void cm_control(u32 mask, u32 set)
 	u32 val;
 
 	raw_spin_lock_irqsave(&cm_lock, flags);
-	val = readl(CM_CTRL) & ~mask;
-	writel(val | set, CM_CTRL);
+	val = readl(cm_base + INTEGRATOR_HDR_CTRL_OFFSET) & ~mask;
+	writel(val | set, cm_base + INTEGRATOR_HDR_CTRL_OFFSET);
 	raw_spin_unlock_irqrestore(&cm_lock, flags);
 }
 
-EXPORT_SYMBOL(cm_control);
+static const char *integrator_arch_str(u32 id)
+{
+	switch ((id >> 16) & 0xff) {
+	case 0x00:
+		return "ASB little-endian";
+	case 0x01:
+		return "AHB little-endian";
+	case 0x03:
+		return "AHB-Lite system bus, bi-endian";
+	case 0x04:
+		return "AHB";
+	case 0x08:
+		return "AHB system bus, ASB processor bus";
+	default:
+		return "Unknown";
+	}
+}
+
+static const char *integrator_fpga_str(u32 id)
+{
+	switch ((id >> 12) & 0xf) {
+	case 0x01:
+		return "XC4062";
+	case 0x02:
+		return "XC4085";
+	case 0x03:
+		return "XVC600";
+	case 0x04:
+		return "EPM7256AE (Altera PLD)";
+	default:
+		return "Unknown";
+	}
+}
+
+void cm_clear_irqs(void)
+{
+	/* disable core module IRQs */
+	writel(0xffffffffU, cm_base + INTEGRATOR_HDR_IC_OFFSET +
+		IRQ_ENABLE_CLEAR);
+}
+
+static const struct of_device_id cm_match[] = {
+	{ .compatible = "arm,core-module-integrator"},
+	{ },
+};
+
+void cm_init(void)
+{
+	struct device_node *cm = of_find_matching_node(NULL, cm_match);
+	u32 val;
+
+	if (!cm) {
+		pr_crit("no core module node found in device tree\n");
+		return;
+	}
+	cm_base = of_iomap(cm, 0);
+	if (!cm_base) {
+		pr_crit("could not remap core module\n");
+		return;
+	}
+	cm_clear_irqs();
+	val = readl(cm_base + INTEGRATOR_HDR_ID_OFFSET);
+	pr_info("Detected ARM core module:\n");
+	pr_info("    Manufacturer: %02x\n", (val >> 24));
+	pr_info("    Architecture: %s\n", integrator_arch_str(val));
+	pr_info("    FPGA: %s\n", integrator_fpga_str(val));
+	pr_info("    Build: %02x\n", (val >> 4) & 0xFF);
+	pr_info("    Rev: %c\n", ('A' + (val & 0x03)));
+}
 
 /*
  * We need to stop things allocating the low memory; ideally we need a
@@ -145,27 +166,7 @@ static ssize_t intcp_get_arch(struct device *dev,
 			      struct device_attribute *attr,
 			      char *buf)
 {
-	const char *arch;
-
-	switch ((integrator_id >> 16) & 0xff) {
-	case 0x00:
-		arch = "ASB little-endian";
-		break;
-	case 0x01:
-		arch = "AHB little-endian";
-		break;
-	case 0x03:
-		arch = "AHB-Lite system bus, bi-endian";
-		break;
-	case 0x04:
-		arch = "AHB";
-		break;
-	default:
-		arch = "Unknown";
-		break;
-	}
-
-	return sprintf(buf, "%s\n", arch);
+	return sprintf(buf, "%s\n", integrator_arch_str(integrator_id));
 }
 
 static struct device_attribute intcp_arch_attr =
@@ -175,24 +176,7 @@ static ssize_t intcp_get_fpga(struct device *dev,
 			      struct device_attribute *attr,
 			      char *buf)
 {
-	const char *fpga;
-
-	switch ((integrator_id >> 12) & 0xf) {
-	case 0x01:
-		fpga = "XC4062";
-		break;
-	case 0x02:
-		fpga = "XC4085";
-		break;
-	case 0x04:
-		fpga = "EPM7256AE (Altera PLD)";
-		break;
-	default:
-		fpga = "Unknown";
-		break;
-	}
-
-	return sprintf(buf, "%s\n", fpga);
+	return sprintf(buf, "%s\n", integrator_fpga_str(integrator_id));
 }
 
 static struct device_attribute intcp_fpga_attr =

arch/arm/mach-integrator/include/mach/irqs.h

-/*
- *  arch/arm/mach-integrator/include/mach/irqs.h
- *
- *  Copyright (C) 1999 ARM Limited
- *  Copyright (C) 2000 Deep Blue Solutions Ltd.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-/*
- * Interrupt numbers, all of the above are just static reservations
- * used so they can be encoded into device resources. They will finally
- * be done away with when switching to device tree.
- */
-#define IRQ_PIC_START			64
-#define IRQ_SOFTINT			(IRQ_PIC_START+0)
-#define IRQ_UARTINT0			(IRQ_PIC_START+1)
-#define IRQ_UARTINT1			(IRQ_PIC_START+2)
-#define IRQ_KMIINT0			(IRQ_PIC_START+3)
-#define IRQ_KMIINT1			(IRQ_PIC_START+4)
-#define IRQ_TIMERINT0			(IRQ_PIC_START+5)
-#define IRQ_TIMERINT1			(IRQ_PIC_START+6)
-#define IRQ_TIMERINT2			(IRQ_PIC_START+7)
-#define IRQ_RTCINT			(IRQ_PIC_START+8)
-#define IRQ_AP_EXPINT0			(IRQ_PIC_START+9)
-#define IRQ_AP_EXPINT1			(IRQ_PIC_START+10)
-#define IRQ_AP_EXPINT2			(IRQ_PIC_START+11)
-#define IRQ_AP_EXPINT3			(IRQ_PIC_START+12)
-#define IRQ_AP_PCIINT0			(IRQ_PIC_START+13)
-#define IRQ_AP_PCIINT1			(IRQ_PIC_START+14)
-#define IRQ_AP_PCIINT2			(IRQ_PIC_START+15)
-#define IRQ_AP_PCIINT3			(IRQ_PIC_START+16)
-#define IRQ_AP_V3INT			(IRQ_PIC_START+17)
-#define IRQ_AP_CPINT0			(IRQ_PIC_START+18)
-#define IRQ_AP_CPINT1			(IRQ_PIC_START+19)
-#define IRQ_AP_LBUSTIMEOUT 		(IRQ_PIC_START+20)
-#define IRQ_AP_APCINT			(IRQ_PIC_START+21)
-#define IRQ_CP_CLCDCINT			(IRQ_PIC_START+22)
-#define IRQ_CP_MMCIINT0			(IRQ_PIC_START+23)
-#define IRQ_CP_MMCIINT1			(IRQ_PIC_START+24)
-#define IRQ_CP_AACIINT			(IRQ_PIC_START+25)
-#define IRQ_CP_CPPLDINT			(IRQ_PIC_START+26)
-#define IRQ_CP_ETHINT			(IRQ_PIC_START+27)
-#define IRQ_CP_TSPENINT			(IRQ_PIC_START+28)
-#define IRQ_PIC_END			(IRQ_PIC_START+28)
-
-#define IRQ_CIC_START			(IRQ_PIC_END+1)
-#define IRQ_CM_SOFTINT			(IRQ_CIC_START+0)
-#define IRQ_CM_COMMRX			(IRQ_CIC_START+1)
-#define IRQ_CM_COMMTX			(IRQ_CIC_START+2)
-#define IRQ_CIC_END			(IRQ_CIC_START+2)
-
-/*
- * IntegratorCP only
- */
-#define IRQ_SIC_START			(IRQ_CIC_END+1)
-#define IRQ_SIC_CP_SOFTINT		(IRQ_SIC_START+0)
-#define IRQ_SIC_CP_RI0			(IRQ_SIC_START+1)
-#define IRQ_SIC_CP_RI1			(IRQ_SIC_START+2)
-#define IRQ_SIC_CP_CARDIN		(IRQ_SIC_START+3)
-#define IRQ_SIC_CP_LMINT0		(IRQ_SIC_START+4)
-#define IRQ_SIC_CP_LMINT1		(IRQ_SIC_START+5)
-#define IRQ_SIC_CP_LMINT2		(IRQ_SIC_START+6)
-#define IRQ_SIC_CP_LMINT3		(IRQ_SIC_START+7)
-#define IRQ_SIC_CP_LMINT4		(IRQ_SIC_START+8)
-#define IRQ_SIC_CP_LMINT5		(IRQ_SIC_START+9)
-#define IRQ_SIC_CP_LMINT6		(IRQ_SIC_START+10)
-#define IRQ_SIC_CP_LMINT7		(IRQ_SIC_START+11)
-#define IRQ_SIC_END			(IRQ_SIC_START+11)

arch/arm/mach-integrator/integrator_ap.c

@@ -51,13 +51,13 @@
 #include <asm/mach-types.h>
 
 #include <mach/lm.h>
-#include <mach/irqs.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach/irq.h>
 #include <asm/mach/map.h>
 #include <asm/mach/time.h>
 
+#include "cm.h"
 #include "common.h"
 #include "pci_v3.h"
 
@@ -146,7 +146,7 @@ static int irq_suspend(void)
 static void irq_resume(void)
 {
 	/* disable all irq sources */
-	writel(-1, VA_CMIC_BASE + IRQ_ENABLE_CLEAR);
+	cm_clear_irqs();
 	writel(-1, VA_IC_BASE + IRQ_ENABLE_CLEAR);
 	writel(-1, VA_IC_BASE + FIQ_ENABLE_CLEAR);
 
@@ -402,8 +402,6 @@ void __init ap_init_early(void)
 {
 }
 
-#ifdef CONFIG_OF
-
 static void __init ap_of_timer_init(void)
 {
 	struct device_node *node;
@@ -450,8 +448,7 @@ static const struct of_device_id fpga_irq_of_match[] __initconst = {
 
 static void __init ap_init_irq_of(void)
 {
-	/* disable core module IRQs */
-	writel(0xffffffffU, VA_CMIC_BASE + IRQ_ENABLE_CLEAR);
+	cm_init();
 	of_irq_init(fpga_irq_of_match);
 	integrator_clk_init(false);
 }
@@ -473,6 +470,11 @@ static struct of_dev_auxdata ap_auxdata_lookup[] __initdata = {
 	{ /* sentinel */ },
 };
 
+static const struct of_device_id ap_syscon_match[] = {
+	{ .compatible = "arm,integrator-ap-syscon"},
+	{ },
+};
+
 static void __init ap_init_of(void)
 {
 	unsigned long sc_dec;
@@ -489,7 +491,8 @@ static void __init ap_init_of(void)
 	root = of_find_node_by_path("/");
 	if (!root)
 		return;
-	syscon = of_find_node_by_path("/syscon");
+
+	syscon = of_find_matching_node(root, ap_syscon_match);
 	if (!syscon)
 		return;
 
@@ -541,7 +544,7 @@ static void __init ap_init_of(void)
 		lmdev->resource.start = 0xc0000000 + 0x10000000 * i;
 		lmdev->resource.end = lmdev->resource.start + 0x0fffffff;
 		lmdev->resource.flags = IORESOURCE_MEM;
-		lmdev->irq = IRQ_AP_EXPINT0 + i;
+		lmdev->irq = irq_of_parse_and_map(syscon, i);
 		lmdev->id = i;
 
 		lm_device_register(lmdev);
@@ -564,136 +567,3 @@ DT_MACHINE_START(INTEGRATOR_AP_DT, "ARM Integrator/AP (Device Tree)")
 	.restart	= integrator_restart,
 	.dt_compat      = ap_dt_board_compat,
 MACHINE_END
-
-#endif
-
-#ifdef CONFIG_ATAGS
-
-/*
- * For the ATAG boot some static mappings are needed. This will
- * go away with the ATAG support down the road.
- */
-
-static struct map_desc ap_io_desc_atag[] __initdata = {
-	{
-		.virtual	= IO_ADDRESS(INTEGRATOR_SC_BASE),
-		.pfn		= __phys_to_pfn(INTEGRATOR_SC_BASE),
-		.length		= SZ_4K,
-		.type		= MT_DEVICE
-	},
-};
-
-static void __init ap_map_io_atag(void)
-{
-	iotable_init(ap_io_desc_atag, ARRAY_SIZE(ap_io_desc_atag));
-	ap_map_io();
-}
-
-/*
- * This is where non-devicetree initialization code is collected and stashed
- * for eventual deletion.
- */
-
-static struct platform_device pci_v3_device = {
-	.name		= "pci-v3",
-	.id		= 0,
-};
-
-static struct resource cfi_flash_resource = {
-	.start		= INTEGRATOR_FLASH_BASE,
-	.end		= INTEGRATOR_FLASH_BASE + INTEGRATOR_FLASH_SIZE - 1,
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device cfi_flash_device = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev		= {
-		.platform_data	= &ap_flash_data,
-	},
-	.num_resources	= 1,
-	.resource	= &cfi_flash_resource,
-};
-
-static void __init ap_timer_init(void)
-{
-	struct clk *clk;
-	unsigned long rate;
-
-	clk = clk_get_sys("ap_timer", NULL);
-	BUG_ON(IS_ERR(clk));
-	clk_prepare_enable(clk);
-	rate = clk_get_rate(clk);
-
-	writel(0, TIMER0_VA_BASE + TIMER_CTRL);
-	writel(0, TIMER1_VA_BASE + TIMER_CTRL);
-	writel(0, TIMER2_VA_BASE + TIMER_CTRL);
-
-	integrator_clocksource_init(rate, (void __iomem *)TIMER2_VA_BASE);
-	integrator_clockevent_init(rate, (void __iomem *)TIMER1_VA_BASE,
-				IRQ_TIMERINT1);
-}
-
-#define INTEGRATOR_SC_VALID_INT	0x003fffff
-
-static void __init ap_init_irq(void)
-{
-	/* Disable all interrupts initially. */
-	/* Do the core module ones */
-	writel(-1, VA_CMIC_BASE + IRQ_ENABLE_CLEAR);
-
-	/* do the header card stuff next */
-	writel(-1, VA_IC_BASE + IRQ_ENABLE_CLEAR);
-	writel(-1, VA_IC_BASE + FIQ_ENABLE_CLEAR);
-
-	fpga_irq_init(VA_IC_BASE, "SC", IRQ_PIC_START,
-		-1, INTEGRATOR_SC_VALID_INT, NULL);
-	integrator_clk_init(false);
-}
-
-static void __init ap_init(void)
-{
-	unsigned long sc_dec;
-	int i;
-
-	platform_device_register(&pci_v3_device);
-	platform_device_register(&cfi_flash_device);
-
-	ap_syscon_base = __io_address(INTEGRATOR_SC_BASE);
-	sc_dec = readl(ap_syscon_base + INTEGRATOR_SC_DEC_OFFSET);
-	for (i = 0; i < 4; i++) {
-		struct lm_device *lmdev;
-
-		if ((sc_dec & (16 << i)) == 0)
-			continue;
-
-		lmdev = kzalloc(sizeof(struct lm_device), GFP_KERNEL);
-		if (!lmdev)
-			continue;
-
-		lmdev->resource.start = 0xc0000000 + 0x10000000 * i;
-		lmdev->resource.end = lmdev->resource.start + 0x0fffffff;
-		lmdev->resource.flags = IORESOURCE_MEM;
-		lmdev->irq = IRQ_AP_EXPINT0 + i;
-		lmdev->id = i;
-
-		lm_device_register(lmdev);
-	}
-
-	integrator_init(false);
-}
-
-MACHINE_START(INTEGRATOR, "ARM-Integrator")
-	/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
-	.atag_offset	= 0x100,
-	.reserve	= integrator_reserve,
-	.map_io		= ap_map_io_atag,
-	.init_early	= ap_init_early,
-	.init_irq	= ap_init_irq,
-	.handle_irq	= fpga_handle_irq,
-	.init_time	= ap_timer_init,
-	.init_machine	= ap_init,
-	.restart	= integrator_restart,
-MACHINE_END
-
-#endif

arch/arm/mach-integrator/integrator_cp.c

@@ -36,9 +36,7 @@
 #include <asm/hardware/arm_timer.h>
 #include <asm/hardware/icst.h>
 
-#include <mach/cm.h>
 #include <mach/lm.h>
-#include <mach/irqs.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach/irq.h>
@@ -50,6 +48,7 @@
 #include <plat/clcd.h>
 #include <plat/sched_clock.h>
 
+#include "cm.h"
 #include "common.h"
 
 /* Base address to the CP controller */
@@ -249,7 +248,6 @@ static void __init intcp_init_early(void)
 #endif
 }
 
-#ifdef CONFIG_OF
 static const struct of_device_id fpga_irq_of_match[] __initconst = {
 	{ .compatible = "arm,versatile-fpga-irq", .data = fpga_irq_of_init, },
 	{ /* Sentinel */ }
@@ -257,6 +255,7 @@ static const struct of_device_id fpga_irq_of_match[] __initconst = {
 
 static void __init intcp_init_irq_of(void)
 {
+	cm_init();
 	of_irq_init(fpga_irq_of_match);
 	integrator_clk_init(true);
 }
@@ -287,6 +286,11 @@ static struct of_dev_auxdata intcp_auxdata_lookup[] __initdata = {
 	{ /* sentinel */ },
 };
 
+static const struct of_device_id intcp_syscon_match[] = {
+	{ .compatible = "arm,integrator-cp-syscon"},
+	{ },
+};
+
 static void __init intcp_init_of(void)
 {
 	struct device_node *root;
@@ -301,7 +305,8 @@ static void __init intcp_init_of(void)
 	root = of_find_node_by_path("/");
 	if (!root)
 		return;
-	cpcon = of_find_node_by_path("/cpcon");
+
+	cpcon = of_find_matching_node(root, intcp_syscon_match);
 	if (!cpcon)
 		return;
 
@@ -354,175 +359,3 @@ DT_MACHINE_START(INTEGRATOR_CP_DT, "ARM Integrator/CP (Device Tree)")
 	.restart	= integrator_restart,
 	.dt_compat      = intcp_dt_board_compat,
 MACHINE_END
-
-#endif
-
-#ifdef CONFIG_ATAGS
-
-/*
- * For the ATAG boot some static mappings are needed. This will
- * go away with the ATAG support down the road.
- */
-
-static struct map_desc intcp_io_desc_atag[] __initdata = {
-	{
-		.virtual	= IO_ADDRESS(INTEGRATOR_CP_CTL_BASE),
-		.pfn		= __phys_to_pfn(INTEGRATOR_CP_CTL_BASE),
-		.length		= SZ_4K,
-		.type		= MT_DEVICE
-	},
-};
-
-static void __init intcp_map_io_atag(void)
-{
-	iotable_init(intcp_io_desc_atag, ARRAY_SIZE(intcp_io_desc_atag));
-	intcp_con_base = __io_address(INTEGRATOR_CP_CTL_BASE);
-	intcp_map_io();
-}
-
-
-/*
- * This is where non-devicetree initialization code is collected and stashed
- * for eventual deletion.
- */
-
-#define INTCP_FLASH_SIZE		SZ_32M
-
-static struct resource intcp_flash_resource = {
-	.start		= INTCP_PA_FLASH_BASE,
-	.end		= INTCP_PA_FLASH_BASE + INTCP_FLASH_SIZE - 1,
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device intcp_flash_device = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev		= {
-		.platform_data	= &intcp_flash_data,
-	},
-	.num_resources	= 1,
-	.resource	= &intcp_flash_resource,
-};
-
-#define INTCP_ETH_SIZE			0x10
-
-static struct resource smc91x_resources[] = {
-	[0] = {
-		.start	= INTEGRATOR_CP_ETH_BASE,
-		.end	= INTEGRATOR_CP_ETH_BASE + INTCP_ETH_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= IRQ_CP_ETHINT,
-		.end	= IRQ_CP_ETHINT,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device smc91x_device = {
-	.name		= "smc91x",
-	.id		= 0,
-	.num_resources	= ARRAY_SIZE(smc91x_resources),
-	.resource	= smc91x_resources,
-};
-
-static struct platform_device *intcp_devs[] __initdata = {
-	&intcp_flash_device,
-	&smc91x_device,
-};
-
-#define INTCP_VA_CIC_BASE		__io_address(INTEGRATOR_HDR_BASE + 0x40)
-#define INTCP_VA_PIC_BASE		__io_address(INTEGRATOR_IC_BASE)
-#define INTCP_VA_SIC_BASE		__io_address(INTEGRATOR_CP_SIC_BASE)
-
-static void __init intcp_init_irq(void)
-{
-	u32 pic_mask, cic_mask, sic_mask;
-
-	/* These masks are for the HW IRQ registers */
-	pic_mask = ~((~0u) << (11 - 0));
-	pic_mask |= (~((~0u) << (29 - 22))) << 22;
-	cic_mask = ~((~0u) << (1 + IRQ_CIC_END - IRQ_CIC_START));
-	sic_mask = ~((~0u) << (1 + IRQ_SIC_END - IRQ_SIC_START));
-
-	/*
-	 * Disable all interrupt sources
-	 */
-	writel(0xffffffff, INTCP_VA_PIC_BASE + IRQ_ENABLE_CLEAR);
-	writel(0xffffffff, INTCP_VA_PIC_BASE + FIQ_ENABLE_CLEAR);
-	writel(0xffffffff, INTCP_VA_CIC_BASE + IRQ_ENABLE_CLEAR);
-	writel(0xffffffff, INTCP_VA_CIC_BASE + FIQ_ENABLE_CLEAR);
-	writel(sic_mask, INTCP_VA_SIC_BASE + IRQ_ENABLE_CLEAR);
-	writel(sic_mask, INTCP_VA_SIC_BASE + FIQ_ENABLE_CLEAR);
-
-	fpga_irq_init(INTCP_VA_PIC_BASE, "PIC", IRQ_PIC_START,
-		      -1, pic_mask, NULL);
-
-	fpga_irq_init(INTCP_VA_CIC_BASE, "CIC", IRQ_CIC_START,
-		      -1, cic_mask, NULL);
-
-	fpga_irq_init(INTCP_VA_SIC_BASE, "SIC", IRQ_SIC_START,
-		      IRQ_CP_CPPLDINT, sic_mask, NULL);
-
-	integrator_clk_init(true);
-}
-
-#define TIMER0_VA_BASE __io_address(INTEGRATOR_TIMER0_BASE)
-#define TIMER1_VA_BASE __io_address(INTEGRATOR_TIMER1_BASE)
-#define TIMER2_VA_BASE __io_address(INTEGRATOR_TIMER2_BASE)
-
-static void __init cp_timer_init(void)
-{
-	writel(0, TIMER0_VA_BASE + TIMER_CTRL);
-	writel(0, TIMER1_VA_BASE + TIMER_CTRL);
-	writel(0, TIMER2_VA_BASE + TIMER_CTRL);
-
-	sp804_clocksource_init(TIMER2_VA_BASE, "timer2");
-	sp804_clockevents_init(TIMER1_VA_BASE, IRQ_TIMERINT1, "timer1");
-}
-
-#define INTEGRATOR_CP_MMC_IRQS	{ IRQ_CP_MMCIINT0, IRQ_CP_MMCIINT1 }
-#define INTEGRATOR_CP_AACI_IRQS	{ IRQ_CP_AACIINT }
-
-static AMBA_APB_DEVICE(mmc, "mmci", 0, INTEGRATOR_CP_MMC_BASE,
-	INTEGRATOR_CP_MMC_IRQS, &mmc_data);
-
-static AMBA_APB_DEVICE(aaci, "aaci", 0, INTEGRATOR_CP_AACI_BASE,
-	INTEGRATOR_CP_AACI_IRQS, NULL);
-
-static AMBA_AHB_DEVICE(clcd, "clcd", 0, INTCP_PA_CLCD_BASE,
-	{ IRQ_CP_CLCDCINT }, &clcd_data);
-
-static struct amba_device *amba_devs[] __initdata = {
-	&mmc_device,
-	&aaci_device,
-	&clcd_device,
-};
-
-static void __init intcp_init(void)
-{
-	int i;
-
-	platform_add_devices(intcp_devs, ARRAY_SIZE(intcp_devs));
-
-	for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
-		struct amba_device *d = amba_devs[i];
-		amba_device_register(d, &iomem_resource);
-	}
-	integrator_init(true);
-}
-
-MACHINE_START(CINTEGRATOR, "ARM-IntegratorCP")
-	/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
-	.atag_offset	= 0x100,
-	.reserve	= integrator_reserve,
-	.map_io		= intcp_map_io_atag,
-	.init_early	= intcp_init_early,
-	.init_irq	= intcp_init_irq,
-	.handle_irq	= fpga_handle_irq,
-	.init_time	= cp_timer_init,
-	.init_machine	= intcp_init,
-	.restart	= integrator_restart,
-MACHINE_END
-
-#endif

arch/arm/mach-integrator/leds.c

@@ -11,10 +11,11 @@
 #include <linux/slab.h>
 #include <linux/leds.h>
 
-#include <mach/cm.h>
 #include <mach/hardware.h>
 #include <mach/platform.h>
 
+#include "cm.h"
+
 #if defined(CONFIG_NEW_LEDS) && defined(CONFIG_LEDS_CLASS)
 
 #define ALPHA_REG __io_address(INTEGRATOR_DBG_BASE)
@@ -78,7 +79,7 @@ static void cm_led_set(struct led_classdev *cdev,
 
 static enum led_brightness cm_led_get(struct led_classdev *cdev)
 {
-	u32 reg = readl(CM_CTRL);
+	u32 reg = cm_get();
 
 	return (reg & CM_CTRL_LED) ? LED_FULL : LED_OFF;
 }

arch/arm/mach-integrator/pci_v3.c

@@ -36,7 +36,6 @@
 
 #include <mach/hardware.h>
 #include <mach/platform.h>
-#include <mach/irqs.h>
 
 #include <asm/mach/map.h>
 #include <asm/signal.h>
@@ -605,7 +604,7 @@ v3_pci_fault(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
 	return 1;
 }
 
-static irqreturn_t v3_irq(int dummy, void *devid)
+static irqreturn_t v3_irq(int irq, void *devid)
 {
 #ifdef CONFIG_DEBUG_LL
 	struct pt_regs *regs = get_irq_regs();
@@ -615,7 +614,7 @@ static irqreturn_t v3_irq(int dummy, void *devid)
 	extern void printascii(const char *);
 
 	sprintf(buf, "V3 int %d: pc=0x%08lx [%08lx] LBFADDR=%08x LBFCODE=%02x "
-		"ISTAT=%02x\n", IRQ_AP_V3INT, pc, instr,
+		"ISTAT=%02x\n", irq, pc, instr,
 		__raw_readl(ap_syscon_base + INTEGRATOR_SC_LBFADDR_OFFSET),
 		__raw_readl(ap_syscon_base + INTEGRATOR_SC_LBFCODE_OFFSET) & 255,
 		v3_readb(V3_LB_ISTAT));
@@ -809,32 +808,6 @@ static u8 __init pci_v3_swizzle(struct pci_dev *dev, u8 *pinp)
 	return pci_common_swizzle(dev, pinp);
 }
 
-static int irq_tab[4] __initdata = {
-	IRQ_AP_PCIINT0,	IRQ_AP_PCIINT1,	IRQ_AP_PCIINT2,	IRQ_AP_PCIINT3
-};
-
-/*
- * map the specified device/slot/pin to an IRQ.  This works out such
- * that slot 9 pin 1 is INT0, pin 2 is INT1, and slot 10 pin 1 is INT1.
- */
-static int __init pci_v3_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-{
-	int intnr = ((slot - 9) + (pin - 1)) & 3;
-
-	return irq_tab[intnr];
-}
-
-static struct hw_pci pci_v3 __initdata = {
-	.swizzle		= pci_v3_swizzle,
-	.setup			= pci_v3_setup,
-	.nr_controllers		= 1,
-	.ops			= &pci_v3_ops,
-	.preinit		= pci_v3_preinit,
-	.postinit		= pci_v3_postinit,
-};
-
-#ifdef CONFIG_OF
-
 static int __init pci_v3_map_irq_dt(const struct pci_dev *dev, u8 slot, u8 pin)
 {
 	struct of_irq oirq;
@@ -851,14 +824,36 @@ static int __init pci_v3_map_irq_dt(const struct pci_dev *dev, u8 slot, u8 pin)
 				     oirq.size);
 }
 
-static int __init pci_v3_dtprobe(struct platform_device *pdev,
-				struct device_node *np)
+static struct hw_pci pci_v3 __initdata = {
+	.swizzle		= pci_v3_swizzle,
+	.setup			= pci_v3_setup,
+	.nr_controllers		= 1,
+	.ops			= &pci_v3_ops,
+	.preinit		= pci_v3_preinit,
+	.postinit		= pci_v3_postinit,
+};
+
+static int __init pci_v3_probe(struct platform_device *pdev)
 {
+	struct device_node *np = pdev->dev.of_node;
 	struct of_pci_range_parser parser;
 	struct of_pci_range range;
 	struct resource *res;
 	int irq, ret;
 
+	/* Remap the Integrator system controller */
+	ap_syscon_base = devm_ioremap(&pdev->dev, INTEGRATOR_SC_BASE, 0x100);
+	if (!ap_syscon_base) {
+		dev_err(&pdev->dev, "unable to remap the AP syscon for PCIv3\n");
+		return -ENODEV;
+	}
+
+	/* Device tree probe path */
+	if (!np) {
+		dev_err(&pdev->dev, "no device tree node for PCIv3\n");
+		return -ENODEV;
+	}
+
 	if (of_pci_range_parser_init(&parser, np))
 		return -EINVAL;
 
@@ -925,76 +920,6 @@ static int __init pci_v3_dtprobe(struct platform_device *pdev,
 	return 0;
 }
 
-#else
-
-static inline int pci_v3_dtprobe(struct platform_device *pdev,
-				  struct device_node *np)
-{
-	return -EINVAL;
-}
-
-#endif
-
-static int __init pci_v3_probe(struct platform_device *pdev)
-{
-	struct device_node *np = pdev->dev.of_node;
-	int ret;
-
-	/* Remap the Integrator system controller */
-	ap_syscon_base = ioremap(INTEGRATOR_SC_BASE, 0x100);
-	if (!ap_syscon_base) {
-		dev_err(&pdev->dev, "unable to remap the AP syscon for PCIv3\n");
-		return -ENODEV;
-	}
-
-	/* Device tree probe path */
-	if (np)
-		return pci_v3_dtprobe(pdev, np);
-
-	pci_v3_base = devm_ioremap(&pdev->dev, PHYS_PCI_V3_BASE, SZ_64K);
-	if (!pci_v3_base) {
-		dev_err(&pdev->dev, "unable to remap PCIv3 base\n");
-		return -ENODEV;
-	}
-
-	ret = devm_request_irq(&pdev->dev, IRQ_AP_V3INT, v3_irq, 0, "V3", NULL);
-	if (ret) {
-		dev_err(&pdev->dev, "unable to grab PCI error interrupt: %d\n",
-			ret);
-		return -ENODEV;
-	}
-
-	conf_mem.name = "PCIv3 config";
-	conf_mem.start = PHYS_PCI_CONFIG_BASE;
-	conf_mem.end = PHYS_PCI_CONFIG_BASE + SZ_16M - 1;
-	conf_mem.flags = IORESOURCE_MEM;
-
-	io_mem.name = "PCIv3 I/O";
-	io_mem.start = PHYS_PCI_IO_BASE;
-	io_mem.end = PHYS_PCI_IO_BASE + SZ_16M - 1;
-	io_mem.flags = IORESOURCE_MEM;
-
-	non_mem_pci = 0x00000000;
-	non_mem_pci_sz = SZ_256M;
-	non_mem.name = "PCIv3 non-prefetched mem";
-	non_mem.start = PHYS_PCI_MEM_BASE;
-	non_mem.end = PHYS_PCI_MEM_BASE + SZ_256M - 1;
-	non_mem.flags = IORESOURCE_MEM;
-
-	pre_mem_pci = 0x10000000;
-	pre_mem_pci_sz = SZ_256M;
-	pre_mem.name = "PCIv3 prefetched mem";
-	pre_mem.start = PHYS_PCI_PRE_BASE + SZ_256M;
-	pre_mem.end = PHYS_PCI_PRE_BASE + SZ_256M - 1;
-	pre_mem.flags = IORESOURCE_MEM | IORESOURCE_PREFETCH;
-
-	pci_v3.map_irq = pci_v3_map_irq;
-
-	pci_common_init_dev(&pdev->dev, &pci_v3);
-
-	return 0;
-}
-
 static const struct of_device_id pci_ids[] = {
 	{ .compatible = "v3,v360epc-pci", },
 	{},

arch/arm/mach-keystone/Kconfig

@@ -9,6 +9,8 @@ config ARCH_KEYSTONE
 	select GENERIC_CLOCKEVENTS
 	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select ARM_ERRATA_798181 if SMP
+	select COMMON_CLK_KEYSTONE
+	select TI_EDMA
 	help
 	  Support for boards based on the Texas Instruments Keystone family of
 	  SoCs.

arch/arm/mach-keystone/Makefile

@@ -4,3 +4,6 @@ plus_sec := $(call as-instr,.arch_extension sec,+sec)
 AFLAGS_smc.o				:=-Wa,-march=armv7-a$(plus_sec)
 
 obj-$(CONFIG_SMP)			+= platsmp.o
+
+# PM domain driver for Keystone SOCs
+obj-$(CONFIG_ARCH_KEYSTONE)		+= pm_domain.o

arch/arm/mach-keystone/pm_domain.c

+/*
+ * PM domain driver for Keystone2 devices
+ *
+ * Copyright 2013 Texas Instruments, Inc.
+ *	Santosh Shilimkar <santosh.shillimkar@ti.com>
+ *
+ * Based on Kevins work on DAVINCI SOCs
+ *	Kevin Hilman <khilman@linaro.org>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/pm_runtime.h>
+#include <linux/pm_clock.h>
+#include <linux/platform_device.h>
+#include <linux/clk-provider.h>
+#include <linux/of.h>
+
+#ifdef CONFIG_PM_RUNTIME
+static int keystone_pm_runtime_suspend(struct device *dev)
+{
+	int ret;
+
+	dev_dbg(dev, "%s\n", __func__);
+
+	ret = pm_generic_runtime_suspend(dev);
+	if (ret)
+		return ret;
+
+	ret = pm_clk_suspend(dev);
+	if (ret) {
+		pm_generic_runtime_resume(dev);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int keystone_pm_runtime_resume(struct device *dev)
+{
+	dev_dbg(dev, "%s\n", __func__);
+
+	pm_clk_resume(dev);
+
+	return pm_generic_runtime_resume(dev);
+}
+#endif
+
+static struct dev_pm_domain keystone_pm_domain = {
+	.ops = {
+		SET_RUNTIME_PM_OPS(keystone_pm_runtime_suspend,
+				   keystone_pm_runtime_resume, NULL)
+		USE_PLATFORM_PM_SLEEP_OPS
+	},
+};
+
+static struct pm_clk_notifier_block platform_domain_notifier = {
+	.pm_domain = &keystone_pm_domain,
+};
+
+static struct of_device_id of_keystone_table[] = {
+	{.compatible = "ti,keystone"},
+	{ /* end of list */ },
+};
+
+int __init keystone_pm_runtime_init(void)
+{
+	struct device_node *np;
+
+	np = of_find_matching_node(NULL, of_keystone_table);
+	if (!np)
+		return 0;
+
+	of_clk_init(NULL);
+	pm_clk_add_notifier(&platform_bus_type, &platform_domain_notifier);
+
+	return 0;
+}
+subsys_initcall(keystone_pm_runtime_init);

arch/arm/mach-kirkwood/Makefile

 obj-y				+= common.o pcie.o
 obj-$(CONFIG_KIRKWOOD_LEGACY)	+= irq.o mpp.o
+obj-$(CONFIG_PM)		+= pm.o
+
 obj-$(CONFIG_MACH_D2NET_V2)		+= d2net_v2-setup.o lacie_v2-common.o
 obj-$(CONFIG_MACH_NET2BIG_V2)		+= netxbig_v2-setup.o lacie_v2-common.o
 obj-$(CONFIG_MACH_NET5BIG_V2)		+= netxbig_v2-setup.o lacie_v2-common.o

arch/arm/mach-kirkwood/common.c

@@ -721,6 +721,7 @@ void __init kirkwood_init(void)
 	kirkwood_xor1_init();
 	kirkwood_crypto_init();
 
+	kirkwood_pm_init();
 	kirkwood_cpuidle_init();
 #ifdef CONFIG_KEXEC
 	kexec_reinit = kirkwood_enable_pcie;

arch/arm/mach-kirkwood/common.h

@@ -58,6 +58,12 @@ void kirkwood_cpufreq_init(void);
 void kirkwood_restart(enum reboot_mode, const char *);
 void kirkwood_clk_init(void);
 
+#ifdef CONFIG_PM
+void kirkwood_pm_init(void);
+#else
+static inline void kirkwood_pm_init(void) {};
+#endif
+
 /* board init functions for boards not fully converted to fdt */
 #ifdef CONFIG_MACH_MV88F6281GTW_GE_DT
 void mv88f6281gtw_ge_init(void);

arch/arm/mach-kirkwood/include/mach/bridge-regs.h

@@ -78,4 +78,6 @@
 #define CGC_TDM			(1 << 20)
 #define CGC_RESERVED		(0x6 << 21)
 
+#define MEMORY_PM_CTRL		(BRIDGE_VIRT_BASE + 0x118)
+
 #endif

arch/arm/mach-kirkwood/pm.c

+/*
+ * Power Management driver for Marvell Kirkwood SoCs
+ *
+ * Copyright (C) 2013 Ezequiel Garcia <ezequiel@free-electrons.com>
+ * Copyright (C) 2010 Simon Guinot <sguinot@lacie.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License,
+ * version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/suspend.h>
+#include <linux/io.h>
+#include <mach/bridge-regs.h>
+
+static void __iomem *ddr_operation_base;
+
+static void kirkwood_low_power(void)
+{
+	u32 mem_pm_ctrl;
+
+	mem_pm_ctrl = readl(MEMORY_PM_CTRL);
+
+	/* Set peripherals to low-power mode */
+	writel_relaxed(~0, MEMORY_PM_CTRL);
+
+	/* Set DDR in self-refresh */
+	writel_relaxed(0x7, ddr_operation_base);
+
+	/*
+	 * Set CPU in wait-for-interrupt state.
+	 * This disables the CPU core clocks,
+	 * the array clocks, and also the L2 controller.
+	 */
+	cpu_do_idle();
+
+	writel_relaxed(mem_pm_ctrl, MEMORY_PM_CTRL);
+}
+
+static int kirkwood_suspend_enter(suspend_state_t state)
+{
+	switch (state) {
+	case PM_SUSPEND_STANDBY:
+		kirkwood_low_power();
+		break;
+	default:
+		return -EINVAL;
+	}
+	return 0;
+}
+
+static int kirkwood_pm_valid_standby(suspend_state_t state)
+{
+	return state == PM_SUSPEND_STANDBY;
+}
+
+static const struct platform_suspend_ops kirkwood_suspend_ops = {
+	.enter = kirkwood_suspend_enter,
+	.valid = kirkwood_pm_valid_standby,
+};
+
+int __init kirkwood_pm_init(void)
+{
+	ddr_operation_base = ioremap(DDR_OPERATION_BASE, 4);
+	suspend_set_ops(&kirkwood_suspend_ops);
+	return 0;
+}