Merge tag 'qcom-dts-for-5.14' of...

Merge tag 'qcom-dts-for-5.14' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt

Qualcomm DTS updates for v5.14

This adds DMA, NAND controllers, USB controller and PHY, RPM, L2CC,
thermal sensors and defines thermal zones. It them enables these for the
RB3011.

* tag 'qcom-dts-for-5.14' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
  ARM: dts: qcom: Enable NAND + USB for RB3011
  ARM: dts: qcom: add L2CC and RPM for IPQ8064
  ARM: dts: qcom: Add USB port definitions to ipq806x
  ARM: dts: qcom: Add tsens details to ipq806x
  ARM: dts: qcom: Add ADM DMA + NAND definitions to ipq806x

Link: https://lore.kernel.org/r/20210614223840.393224-1-bjorn.andersson@linaro.orgSigned-off-by: Olof Johansson <olof@lixom.net>

arch/arm/boot/dts/qcom-ipq8064-rb3011.dts

@@ -216,6 +216,10 @@ led@7 {
 	};
 };
 
+&adm_dma {
+	status = "okay";
+};
+
 &gmac0 {
 	status = "okay";
 
@@ -251,6 +255,39 @@ &gsbi7_serial {
 	status = "okay";
 };
 
+&hs_phy_1 {
+	status = "okay";
+};
+
+&nand {
+	status = "okay";
+
+	nandcs@0 {
+		compatible = "qcom,nandcs";
+		reg = <0>;
+
+		nand-ecc-strength = <4>;
+		nand-bus-width = <8>;
+		nand-ecc-step-size = <512>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			boot@0 {
+				label = "RouterBoard NAND 1 Boot";
+				reg = <0x0000000 0x0800000>;
+			};
+
+			main@800000 {
+				label = "RouterBoard NAND 1 Main";
+				reg = <0x0800000 0x7800000>;
+			};
+		};
+	};
+};
+
 &qcom_pinmux {
 	buttons_pins: buttons_pins {
 		mux {
@@ -305,4 +342,25 @@ mux {
 			input-disable;
 		};
 	};
+
+	usb1_pwr_en_pins: usb1_pwr_en_pins {
+		mux {
+			pins = "gpio4";
+			function = "gpio";
+			drive-strength = <16>;
+			bias-disable;
+			output-high;
+		};
+	};
+};
+
+&ss_phy_1 {
+	status = "okay";
+};
+
+&usb3_1 {
+	pinctrl-0 = <&usb1_pwr_en_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
 };

arch/arm/boot/dts/qcom-ipq8064.dtsi

@@ -2,6 +2,8 @@
 /dts-v1/;
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
 #include <dt-bindings/clock/qcom,gcc-ipq806x.h>
 #include <dt-bindings/clock/qcom,lcc-ipq806x.h>
 #include <dt-bindings/gpio/gpio.h>
@@ -46,6 +48,228 @@ L2: l2-cache {
 		};
 	};
 
+	thermal-zones {
+		tsens_tz_sensor0 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 0>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		tsens_tz_sensor1 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 1>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		tsens_tz_sensor2 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 2>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		tsens_tz_sensor3 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 3>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		tsens_tz_sensor4 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 4>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		tsens_tz_sensor5 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 5>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		tsens_tz_sensor6 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 6>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		tsens_tz_sensor7 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 7>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		tsens_tz_sensor8 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 8>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		tsens_tz_sensor9 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 9>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		tsens_tz_sensor10 {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 10>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+	};
+
 	memory {
 		device_type = "memory";
 		reg = <0x0 0x0>;
@@ -185,6 +409,31 @@ mux {
 					bias-pull-up;
 				};
 			};
+
+			nand_pins: nand_pins {
+				mux {
+					pins = "gpio34", "gpio35", "gpio36",
+					       "gpio37", "gpio38", "gpio39",
+					       "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					function = "nand";
+					drive-strength = <10>;
+					bias-disable;
+				};
+
+				pullups {
+					pins = "gpio39";
+					bias-pull-up;
+				};
+
+				hold {
+					pins = "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					bias-bus-hold;
+				};
+			};
 		};
 
 		intc: interrupt-controller@2000000 {
@@ -226,6 +475,26 @@ acc1: clock-controller@2098000 {
 			reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
 		};
 
+		adm_dma: dma-controller@18300000 {
+			compatible = "qcom,adm";
+			reg = <0x18300000 0x100000>;
+			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+
+			clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
+			clock-names = "core", "iface";
+
+			resets = <&gcc ADM0_RESET>,
+				 <&gcc ADM0_PBUS_RESET>,
+				 <&gcc ADM0_C0_RESET>,
+				 <&gcc ADM0_C1_RESET>,
+				 <&gcc ADM0_C2_RESET>;
+			reset-names = "clk", "pbus", "c0", "c1", "c2";
+			qcom,ee = <0>;
+
+			status = "disabled";
+		};
+
 		saw0: regulator@2089000 {
 			compatible = "qcom,saw2";
 			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
@@ -403,6 +672,28 @@ sata_phy: sata-phy@1b400000 {
 			status = "disabled";
 		};
 
+		nand: nand-controller@1ac00000 {
+			compatible = "qcom,ipq806x-nand";
+			reg = <0x1ac00000 0x800>;
+
+			pinctrl-0 = <&nand_pins>;
+			pinctrl-names = "default";
+
+			clocks = <&gcc EBI2_CLK>,
+				 <&gcc EBI2_AON_CLK>;
+			clock-names = "core", "aon";
+
+			dmas = <&adm_dma 3>;
+			dma-names = "rxtx";
+			qcom,cmd-crci = <15>;
+			qcom,data-crci = <3>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
 		sata: sata@29000000 {
 			compatible = "qcom,ipq806x-ahci", "generic-ahci";
 			reg = <0x29000000 0x180>;
@@ -436,6 +727,12 @@ qfprom: qfprom@700000 {
 			reg = <0x00700000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
+			tsens_calib: calib@400 {
+				reg = <0x400 0xb>;
+			};
+			tsens_calib_backup: calib_backup@410 {
+				reg = <0x410 0xb>;
+			};
 		};
 
 		gcc: clock-controller@900000 {
@@ -443,6 +740,38 @@ gcc: clock-controller@900000 {
 			reg = <0x00900000 0x4000>;
 			#clock-cells = <1>;
 			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+
+			tsens: thermal-sensor@900000 {
+				compatible = "qcom,ipq8064-tsens";
+
+				nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>;
+				nvmem-cell-names = "calib", "calib_backup";
+				interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "uplow";
+
+				#qcom,sensors = <11>;
+				#thermal-sensor-cells = <1>;
+			};
+		};
+
+		rpm: rpm@108000 {
+			compatible = "qcom,rpm-ipq8064";
+			reg = <0x108000 0x1000>;
+			qcom,ipc = <&l2cc 0x8 2>;
+
+			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ack", "err", "wakeup";
+
+			clocks = <&gcc RPM_MSG_RAM_H_CLK>;
+			clock-names = "ram";
+
+			rpmcc: clock-controller {
+				compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
+				#clock-cells = <1>;
+			};
 		};
 
 		tcsr: syscon@1a400000 {
@@ -450,6 +779,14 @@ tcsr: syscon@1a400000 {
 			reg = <0x1a400000 0x100>;
 		};
 
+		l2cc: clock-controller@2011000 {
+			compatible = "qcom,kpss-gcc", "syscon";
+			reg = <0x2011000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&gcc PXO_SRC>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu_l2_aux";
+		};
+
 		lcc: clock-controller@28000000 {
 			compatible = "qcom,lcc-ipq8064";
 			reg = <0x28000000 0x1000>;
@@ -718,6 +1055,94 @@ gmac3: ethernet@37600000 {
 			status = "disabled";
 		};
 
+		hs_phy_0: phy@100f8800 {
+			compatible = "qcom,ipq806x-usb-phy-hs";
+			reg = <0x100f8800 0x30>;
+			clocks = <&gcc USB30_0_UTMI_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		ss_phy_0: phy@100f8830 {
+			compatible = "qcom,ipq806x-usb-phy-ss";
+			reg = <0x100f8830 0x30>;
+			clocks = <&gcc USB30_0_MASTER_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		usb3_0: usb3@100f8800 {
+			compatible = "qcom,dwc3", "syscon";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x100f8800 0x8000>;
+			clocks = <&gcc USB30_0_MASTER_CLK>;
+			clock-names = "core";
+
+			ranges;
+
+			resets = <&gcc USB30_0_MASTER_RESET>;
+			reset-names = "master";
+
+			status = "disabled";
+
+			dwc3_0: dwc3@10000000 {
+				compatible = "snps,dwc3";
+				reg = <0x10000000 0xcd00>;
+				interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&hs_phy_0>, <&ss_phy_0>;
+				phy-names = "usb2-phy", "usb3-phy";
+				dr_mode = "host";
+				snps,dis_u3_susphy_quirk;
+			};
+		};
+
+		hs_phy_1: phy@110f8800 {
+			compatible = "qcom,ipq806x-usb-phy-hs";
+			reg = <0x110f8800 0x30>;
+			clocks = <&gcc USB30_1_UTMI_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+		};
+
+		ss_phy_1: phy@110f8830 {
+			compatible = "qcom,ipq806x-usb-phy-ss";
+			reg = <0x110f8830 0x30>;
+			clocks = <&gcc USB30_1_MASTER_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+		};
+
+		usb3_1: usb3@110f8800 {
+			compatible = "qcom,dwc3", "syscon";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x110f8800 0x8000>;
+			clocks = <&gcc USB30_1_MASTER_CLK>;
+			clock-names = "core";
+
+			ranges;
+
+			resets = <&gcc USB30_1_MASTER_RESET>;
+			reset-names = "master";
+
+			status = "disabled";
+
+			dwc3_1: dwc3@11000000 {
+				compatible = "snps,dwc3";
+				reg = <0x11000000 0xcd00>;
+				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&hs_phy_1>, <&ss_phy_1>;
+				phy-names = "usb2-phy", "usb3-phy";
+				dr_mode = "host";
+				snps,dis_u3_susphy_quirk;
+			};
+		};
+
 		vsdcc_fixed: vsdcc-regulator {
 			compatible = "regulator-fixed";
 			regulator-name = "SDCC Power";