Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2015-09-23

This series contains updates to ixgbe only.

Mark provides all the changes in this series, first clears the destination
location for I2C data initially so that the received data will not be
corrupted by previous attempts.  Then reduced the pauses/delays in the
PHY detection when no SFP is present by reducing the number of retires,
once an SFP is detected, the "normal" number of retries in PHY detection
will be used.  Added support for X55EM_x SFP+ dual-speed, and fixed 1G and
10G link stability for X550EM_x by configuring the CS4227 correctly by
moving code to ixgbe_setup_mac_link_sfp_x550em().  Added functionality to
reset CS4227, since on some platforms the CS4227 does not initialize
properly.  Next reduces the SFP polling rate, due to when an SFP is not
present, the I2C timeouts that result are very costly.  So prevent the
SFP polling from being done more than once every two seconds.  Added
support for I2C bus MUX.  Fixed the setting of RDRXCTL register which
should fall through X540 and 82599, not 82598.  In addition, added small
packet padding support in X550 by setting RDRXCTL.PSP when the driver is
in SRIOV mode.  Fixed a known hardware issue where the PCI transactions
pending bit sticks high when there are pending transactions, so
workaround the issue by wait and then continue with our reset flow.
Added a new device ID for X550EM device with SFPs.  Provided a fix with
the DCA setup, which was suggested by Alex Duyck <aduyck@mirantis.com>,
by making it so that we always set the relaxed ordering bits related to
the DCA registers even if DCA is not enbaled.  Then moves the
configuration out of the ixgbe_down() and into ixgbe_configure() before
enabling the transmit and receive rings.  This ensures that DCA is
configured correctly before starting the processing of packets.
Fixed VM-to-VM loopback mode which requires that FCRTH be set, but
the datasheets did not specify what the value should be.  It has now
been determined that the correct value should be RXPBSIZE - (24*1024).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/intel/ixgbe/ixgbe.h

@@ -594,6 +594,7 @@ struct ixgbe_mac_addr {
 
 /* default to trying for four seconds */
 #define IXGBE_TRY_LINK_TIMEOUT (4 * HZ)
+#define IXGBE_SFP_POLL_JIFFIES (2 * HZ)	/* SFP poll every 2 seconds */
 
 /* board specific private data structure */
 struct ixgbe_adapter {
@@ -707,6 +708,7 @@ struct ixgbe_adapter {
 
 	u32 link_speed;
 	bool link_up;
+	unsigned long sfp_poll_time;
 	unsigned long link_check_timeout;
 
 	struct timer_list service_timer;

drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c

@@ -44,9 +44,8 @@
 static void ixgbe_disable_tx_laser_multispeed_fiber(struct ixgbe_hw *hw);
 static void ixgbe_enable_tx_laser_multispeed_fiber(struct ixgbe_hw *hw);
 static void ixgbe_flap_tx_laser_multispeed_fiber(struct ixgbe_hw *hw);
-static s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
-						 ixgbe_link_speed speed,
-						 bool autoneg_wait_to_complete);
+static void
+ixgbe_set_hard_rate_select_speed(struct ixgbe_hw *, ixgbe_link_speed);
 static s32 ixgbe_setup_mac_link_smartspeed(struct ixgbe_hw *hw,
 					   ixgbe_link_speed speed,
 					   bool autoneg_wait_to_complete);
@@ -109,6 +108,9 @@ static void ixgbe_init_mac_link_ops_82599(struct ixgbe_hw *hw)
 	if (hw->phy.multispeed_fiber) {
 		/* Set up dual speed SFP+ support */
 		mac->ops.setup_link = &ixgbe_setup_mac_link_multispeed_fiber;
+		mac->ops.setup_mac_link = ixgbe_setup_mac_link_82599;
+		mac->ops.set_rate_select_speed =
+					       ixgbe_set_hard_rate_select_speed;
 	} else {
 		if ((mac->ops.get_media_type(hw) ==
 		     ixgbe_media_type_backplane) &&
@@ -646,176 +648,32 @@ static void ixgbe_flap_tx_laser_multispeed_fiber(struct ixgbe_hw *hw)
 }
 
 /**
- *  ixgbe_setup_mac_link_multispeed_fiber - Set MAC link speed
+ * ixgbe_set_hard_rate_select_speed - Set module link speed
  * @hw: pointer to hardware structure
- *  @speed: new link speed
- *  @autoneg_wait_to_complete: true when waiting for completion is needed
+ * @speed: link speed to set
  *
- *  Set the link speed in the AUTOC register and restarts link.
- **/
-static s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
-					  ixgbe_link_speed speed,
-					  bool autoneg_wait_to_complete)
+ * Set module link speed via RS0/RS1 rate select pins.
+ */
+static void
+ixgbe_set_hard_rate_select_speed(struct ixgbe_hw *hw, ixgbe_link_speed speed)
 {
-	s32 status = 0;
-	ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
-	ixgbe_link_speed highest_link_speed = IXGBE_LINK_SPEED_UNKNOWN;
-	u32 speedcnt = 0;
 	u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP);
-	u32 i = 0;
-	bool link_up = false;
-	bool autoneg = false;
 
-	/* Mask off requested but non-supported speeds */
-	status = hw->mac.ops.get_link_capabilities(hw, &link_speed,
-						   &autoneg);
-	if (status != 0)
-		return status;
-
-	speed &= link_speed;
-
-	/*
-	 * Try each speed one by one, highest priority first.  We do this in
-	 * software because 10gb fiber doesn't support speed autonegotiation.
-	 */
-	if (speed & IXGBE_LINK_SPEED_10GB_FULL) {
-		speedcnt++;
-		highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL;
-
-		/* If we already have link at this speed, just jump out */
-		status = hw->mac.ops.check_link(hw, &link_speed, &link_up,
-						false);
-		if (status != 0)
-			return status;
-
-		if ((link_speed == IXGBE_LINK_SPEED_10GB_FULL) && link_up)
-			goto out;
-
-		/* Set the module link speed */
-		switch (hw->phy.media_type) {
-		case ixgbe_media_type_fiber:
+	switch (speed) {
+	case IXGBE_LINK_SPEED_10GB_FULL:
 		esdp_reg |= (IXGBE_ESDP_SDP5_DIR | IXGBE_ESDP_SDP5);
-			IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
-			IXGBE_WRITE_FLUSH(hw);
-			break;
-		case ixgbe_media_type_fiber_qsfp:
-			/* QSFP module automatically detects MAC link speed */
 		break;
-		default:
-			hw_dbg(hw, "Unexpected media type.\n");
-			break;
-		}
-
-		/* Allow module to change analog characteristics (1G->10G) */
-		msleep(40);
-
-		status = ixgbe_setup_mac_link_82599(hw,
-						    IXGBE_LINK_SPEED_10GB_FULL,
-						    autoneg_wait_to_complete);
-		if (status != 0)
-			return status;
-
-		/* Flap the tx laser if it has not already been done */
-		if (hw->mac.ops.flap_tx_laser)
-			hw->mac.ops.flap_tx_laser(hw);
-
-		/*
-		 * Wait for the controller to acquire link.  Per IEEE 802.3ap,
-		 * Section 73.10.2, we may have to wait up to 500ms if KR is
-		 * attempted.  82599 uses the same timing for 10g SFI.
-		 */
-		for (i = 0; i < 5; i++) {
-			/* Wait for the link partner to also set speed */
-			msleep(100);
-
-			/* If we have link, just jump out */
-			status = hw->mac.ops.check_link(hw, &link_speed,
-							&link_up, false);
-			if (status != 0)
-				return status;
-
-			if (link_up)
-				goto out;
-		}
-	}
-
-	if (speed & IXGBE_LINK_SPEED_1GB_FULL) {
-		speedcnt++;
-		if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN)
-			highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL;
-
-		/* If we already have link at this speed, just jump out */
-		status = hw->mac.ops.check_link(hw, &link_speed, &link_up,
-						false);
-		if (status != 0)
-			return status;
-
-		if ((link_speed == IXGBE_LINK_SPEED_1GB_FULL) && link_up)
-			goto out;
-
-		/* Set the module link speed */
-		switch (hw->phy.media_type) {
-		case ixgbe_media_type_fiber:
+	case IXGBE_LINK_SPEED_1GB_FULL:
 		esdp_reg &= ~IXGBE_ESDP_SDP5;
 		esdp_reg |= IXGBE_ESDP_SDP5_DIR;
-			IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
-			IXGBE_WRITE_FLUSH(hw);
-			break;
-		case ixgbe_media_type_fiber_qsfp:
-			/* QSFP module automatically detects MAC link speed */
 		break;
 	default:
-			hw_dbg(hw, "Unexpected media type.\n");
-			break;
-		}
-
-		/* Allow module to change analog characteristics (10G->1G) */
-		msleep(40);
-
-		status = ixgbe_setup_mac_link_82599(hw,
-						    IXGBE_LINK_SPEED_1GB_FULL,
-						    autoneg_wait_to_complete);
-		if (status != 0)
-			return status;
-
-		/* Flap the tx laser if it has not already been done */
-		if (hw->mac.ops.flap_tx_laser)
-			hw->mac.ops.flap_tx_laser(hw);
-
-		/* Wait for the link partner to also set speed */
-		msleep(100);
-
-		/* If we have link, just jump out */
-		status = hw->mac.ops.check_link(hw, &link_speed, &link_up,
-						false);
-		if (status != 0)
-			return status;
-
-		if (link_up)
-			goto out;
+		hw_dbg(hw, "Invalid fixed module speed\n");
+		return;
 	}
 
-	/*
-	 * We didn't get link.  Configure back to the highest speed we tried,
-	 * (if there was more than one).  We call ourselves back with just the
-	 * single highest speed that the user requested.
-	 */
-	if (speedcnt > 1)
-		status = ixgbe_setup_mac_link_multispeed_fiber(hw,
-							       highest_link_speed,
-							       autoneg_wait_to_complete);
-
-out:
-	/* Set autoneg_advertised value based on input link speed */
-	hw->phy.autoneg_advertised = 0;
-
-	if (speed & IXGBE_LINK_SPEED_10GB_FULL)
-		hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL;
-
-	if (speed & IXGBE_LINK_SPEED_1GB_FULL)
-		hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL;
-
-	return status;
+	IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
+	IXGBE_WRITE_FLUSH(hw);
 }
 
 /**

drivers/net/ethernet/intel/ixgbe/ixgbe_common.c

@@ -297,13 +297,13 @@ s32 ixgbe_start_hw_generic(struct ixgbe_hw *hw)
 
 	/* Setup flow control */
 	ret_val = ixgbe_setup_fc(hw);
-	if (!ret_val)
-		return 0;
+	if (ret_val)
+		return ret_val;
 
 	/* Clear adapter stopped flag */
 	hw->adapter_stopped = false;
 
-	return ret_val;
+	return 0;
 }
 
 /**
@@ -2164,10 +2164,11 @@ s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw)
 			/*
 			 * In order to prevent Tx hangs when the internal Tx
 			 * switch is enabled we must set the high water mark
-			 * to the maximum FCRTH value.  This allows the Tx
-			 * switch to function even under heavy Rx workloads.
+			 * to the Rx packet buffer size - 24KB.  This allows
+			 * the Tx switch to function even under heavy Rx
+			 * workloads.
 			 */
-			fcrth = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(i)) - 32;
+			fcrth = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(i)) - 24576;
 		}
 
 		IXGBE_WRITE_REG(hw, IXGBE_FCRTH_82599(i), fcrth);
@@ -2476,6 +2477,9 @@ static s32 ixgbe_disable_pcie_master(struct ixgbe_hw *hw)
 	hw_dbg(hw, "GIO Master Disable bit didn't clear - requesting resets\n");
 	hw->mac.flags |= IXGBE_FLAGS_DOUBLE_RESET_REQUIRED;
 
+	if (hw->mac.type >= ixgbe_mac_X550)
+		return 0;
+
 	/*
 	 * Before proceeding, make sure that the PCIe block does not have
 	 * transactions pending.
@@ -3920,3 +3924,213 @@ bool ixgbe_mng_present(struct ixgbe_hw *hw)
 	fwsm &= IXGBE_FWSM_MODE_MASK;
 	return fwsm == IXGBE_FWSM_FW_MODE_PT;
 }
+
+/**
+ *  ixgbe_setup_mac_link_multispeed_fiber - Set MAC link speed
+ *  @hw: pointer to hardware structure
+ *  @speed: new link speed
+ *  @autoneg_wait_to_complete: true when waiting for completion is needed
+ *
+ *  Set the link speed in the MAC and/or PHY register and restarts link.
+ */
+s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
+					  ixgbe_link_speed speed,
+					  bool autoneg_wait_to_complete)
+{
+	ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
+	ixgbe_link_speed highest_link_speed = IXGBE_LINK_SPEED_UNKNOWN;
+	s32 status = 0;
+	u32 speedcnt = 0;
+	u32 i = 0;
+	bool autoneg, link_up = false;
+
+	/* Mask off requested but non-supported speeds */
+	status = hw->mac.ops.get_link_capabilities(hw, &link_speed, &autoneg);
+	if (status)
+		return status;
+
+	speed &= link_speed;
+
+	/* Try each speed one by one, highest priority first.  We do this in
+	 * software because 10Gb fiber doesn't support speed autonegotiation.
+	 */
+	if (speed & IXGBE_LINK_SPEED_10GB_FULL) {
+		speedcnt++;
+		highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL;
+
+		/* If we already have link at this speed, just jump out */
+		status = hw->mac.ops.check_link(hw, &link_speed, &link_up,
+						false);
+		if (status)
+			return status;
+
+		if (link_speed == IXGBE_LINK_SPEED_10GB_FULL && link_up)
+			goto out;
+
+		/* Set the module link speed */
+		switch (hw->phy.media_type) {
+		case ixgbe_media_type_fiber:
+			hw->mac.ops.set_rate_select_speed(hw,
+						    IXGBE_LINK_SPEED_10GB_FULL);
+			break;
+		case ixgbe_media_type_fiber_qsfp:
+			/* QSFP module automatically detects MAC link speed */
+			break;
+		default:
+			hw_dbg(hw, "Unexpected media type\n");
+			break;
+		}
+
+		/* Allow module to change analog characteristics (1G->10G) */
+		msleep(40);
+
+		status = hw->mac.ops.setup_mac_link(hw,
+						    IXGBE_LINK_SPEED_10GB_FULL,
+						    autoneg_wait_to_complete);
+		if (status)
+			return status;
+
+		/* Flap the Tx laser if it has not already been done */
+		if (hw->mac.ops.flap_tx_laser)
+			hw->mac.ops.flap_tx_laser(hw);
+
+		/* Wait for the controller to acquire link.  Per IEEE 802.3ap,
+		 * Section 73.10.2, we may have to wait up to 500ms if KR is
+		 * attempted.  82599 uses the same timing for 10g SFI.
+		 */
+		for (i = 0; i < 5; i++) {
+			/* Wait for the link partner to also set speed */
+			msleep(100);
+
+			/* If we have link, just jump out */
+			status = hw->mac.ops.check_link(hw, &link_speed,
+							&link_up, false);
+			if (status)
+				return status;
+
+			if (link_up)
+				goto out;
+		}
+	}
+
+	if (speed & IXGBE_LINK_SPEED_1GB_FULL) {
+		speedcnt++;
+		if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN)
+			highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL;
+
+		/* If we already have link at this speed, just jump out */
+		status = hw->mac.ops.check_link(hw, &link_speed, &link_up,
+						false);
+		if (status)
+			return status;
+
+		if (link_speed == IXGBE_LINK_SPEED_1GB_FULL && link_up)
+			goto out;
+
+		/* Set the module link speed */
+		switch (hw->phy.media_type) {
+		case ixgbe_media_type_fiber:
+			hw->mac.ops.set_rate_select_speed(hw,
+						     IXGBE_LINK_SPEED_1GB_FULL);
+			break;
+		case ixgbe_media_type_fiber_qsfp:
+			/* QSFP module automatically detects link speed */
+			break;
+		default:
+			hw_dbg(hw, "Unexpected media type\n");
+			break;
+		}
+
+		/* Allow module to change analog characteristics (10G->1G) */
+		msleep(40);
+
+		status = hw->mac.ops.setup_mac_link(hw,
+						    IXGBE_LINK_SPEED_1GB_FULL,
+						    autoneg_wait_to_complete);
+		if (status)
+			return status;
+
+		/* Flap the Tx laser if it has not already been done */
+		if (hw->mac.ops.flap_tx_laser)
+			hw->mac.ops.flap_tx_laser(hw);
+
+		/* Wait for the link partner to also set speed */
+		msleep(100);
+
+		/* If we have link, just jump out */
+		status = hw->mac.ops.check_link(hw, &link_speed, &link_up,
+						false);
+		if (status)
+			return status;
+
+		if (link_up)
+			goto out;
+	}
+
+	/* We didn't get link.  Configure back to the highest speed we tried,
+	 * (if there was more than one).  We call ourselves back with just the
+	 * single highest speed that the user requested.
+	 */
+	if (speedcnt > 1)
+		status = ixgbe_setup_mac_link_multispeed_fiber(hw,
+						      highest_link_speed,
+						      autoneg_wait_to_complete);
+
+out:
+	/* Set autoneg_advertised value based on input link speed */
+	hw->phy.autoneg_advertised = 0;
+
+	if (speed & IXGBE_LINK_SPEED_10GB_FULL)
+		hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL;
+
+	if (speed & IXGBE_LINK_SPEED_1GB_FULL)
+		hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL;
+
+	return status;
+}
+
+/**
+ *  ixgbe_set_soft_rate_select_speed - Set module link speed
+ *  @hw: pointer to hardware structure
+ *  @speed: link speed to set
+ *
+ *  Set module link speed via the soft rate select.
+ */
+void ixgbe_set_soft_rate_select_speed(struct ixgbe_hw *hw,
+				      ixgbe_link_speed speed)
+{
+	s32 status;
+	u8 rs, eeprom_data;
+
+	switch (speed) {
+	case IXGBE_LINK_SPEED_10GB_FULL:
+		/* one bit mask same as setting on */
+		rs = IXGBE_SFF_SOFT_RS_SELECT_10G;
+		break;
+	case IXGBE_LINK_SPEED_1GB_FULL:
+		rs = IXGBE_SFF_SOFT_RS_SELECT_1G;
+		break;
+	default:
+		hw_dbg(hw, "Invalid fixed module speed\n");
+		return;
+	}
+
+	/* Set RS0 */
+	status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB,
+					   IXGBE_I2C_EEPROM_DEV_ADDR2,
+					   &eeprom_data);
+	if (status) {
+		hw_dbg(hw, "Failed to read Rx Rate Select RS0\n");
+		return;
+	}
+
+	eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) | rs;
+
+	status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB,
+					    IXGBE_I2C_EEPROM_DEV_ADDR2,
+					    eeprom_data);
+	if (status) {
+		hw_dbg(hw, "Failed to write Rx Rate Select RS0\n");
+		return;
+	}
+}

drivers/net/ethernet/intel/ixgbe/ixgbe_common.h

@@ -135,6 +135,11 @@ s32 ixgbe_get_thermal_sensor_data_generic(struct ixgbe_hw *hw);
 s32 ixgbe_init_thermal_sensor_thresh_generic(struct ixgbe_hw *hw);
 void ixgbe_disable_rx_generic(struct ixgbe_hw *hw);
 void ixgbe_enable_rx_generic(struct ixgbe_hw *hw);
+s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
+					  ixgbe_link_speed speed,
+					  bool autoneg_wait_to_complete);
+void ixgbe_set_soft_rate_select_speed(struct ixgbe_hw *hw,
+				      ixgbe_link_speed speed);
 
 #define IXGBE_FAILED_READ_REG 0xffffffffU
 #define IXGBE_FAILED_READ_CFG_DWORD 0xffffffffU

drivers/net/ethernet/intel/ixgbe/ixgbe_dcb_82599.c

@@ -259,7 +259,13 @@ s32 ixgbe_dcb_config_pfc_82599(struct ixgbe_hw *hw, u8 pfc_en, u8 *prio_tc)
 			fcrtl = (hw->fc.low_water[i] << 10) | IXGBE_FCRTL_XONE;
 			IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(i), fcrtl);
 		} else {
-			reg = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(i)) - 32;
+			/* In order to prevent Tx hangs when the internal Tx
+			 * switch is enabled we must set the high water mark
+			 * to the Rx packet buffer size - 24KB.  This allows
+			 * the Tx switch to function even under heavy Rx
+			 * workloads.
+			 */
+			reg = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(i)) - 24576;
 			IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(i), 0);
 		}
 

drivers/net/ethernet/intel/ixgbe/ixgbe_main.c

@@ -79,7 +79,7 @@ char ixgbe_default_device_descr[] =
 static char ixgbe_default_device_descr[] =
 			      "Intel(R) 10 Gigabit Network Connection";
 #endif
-#define DRV_VERSION "4.0.1-k"
+#define DRV_VERSION "4.2.1-k"
 const char ixgbe_driver_version[] = DRV_VERSION;
 static const char ixgbe_copyright[] =
 				"Copyright (c) 1999-2015 Intel Corporation.";
@@ -137,6 +137,7 @@ static const struct pci_device_id ixgbe_pci_tbl[] = {
 	{PCI_VDEVICE(INTEL, IXGBE_DEV_ID_X550EM_X_KX4), board_X550EM_x},
 	{PCI_VDEVICE(INTEL, IXGBE_DEV_ID_X550EM_X_KR), board_X550EM_x},
 	{PCI_VDEVICE(INTEL, IXGBE_DEV_ID_X550EM_X_10G_T), board_X550EM_x},
+	{PCI_VDEVICE(INTEL, IXGBE_DEV_ID_X550EM_X_SFP), board_X550EM_x},
 	/* required last entry */
 	{0, }
 };
@@ -1244,9 +1245,12 @@ static void ixgbe_update_tx_dca(struct ixgbe_adapter *adapter,
 				int cpu)
 {
 	struct ixgbe_hw *hw = &adapter->hw;
-	u32 txctrl = dca3_get_tag(tx_ring->dev, cpu);
+	u32 txctrl = 0;
 	u16 reg_offset;
 
+	if (adapter->flags & IXGBE_FLAG_DCA_ENABLED)
+		txctrl = dca3_get_tag(tx_ring->dev, cpu);
+
 	switch (hw->mac.type) {
 	case ixgbe_mac_82598EB:
 		reg_offset = IXGBE_DCA_TXCTRL(tx_ring->reg_idx);
@@ -1278,9 +1282,11 @@ static void ixgbe_update_rx_dca(struct ixgbe_adapter *adapter,
 				int cpu)
 {
 	struct ixgbe_hw *hw = &adapter->hw;
-	u32 rxctrl = dca3_get_tag(rx_ring->dev, cpu);
+	u32 rxctrl = 0;
 	u8 reg_idx = rx_ring->reg_idx;
 
+	if (adapter->flags & IXGBE_FLAG_DCA_ENABLED)
+		rxctrl = dca3_get_tag(rx_ring->dev, cpu);
 
 	switch (hw->mac.type) {
 	case ixgbe_mac_82599EB:
@@ -1297,6 +1303,7 @@ static void ixgbe_update_rx_dca(struct ixgbe_adapter *adapter,
 	 * which will cause the DCA tag to be cleared.
 	 */
 	rxctrl |= IXGBE_DCA_RXCTRL_DESC_RRO_EN |
+		  IXGBE_DCA_RXCTRL_DATA_DCA_EN |
 		  IXGBE_DCA_RXCTRL_DESC_DCA_EN;
 
 	IXGBE_WRITE_REG(hw, IXGBE_DCA_RXCTRL(reg_idx), rxctrl);
@@ -1326,11 +1333,13 @@ static void ixgbe_setup_dca(struct ixgbe_adapter *adapter)
 {
 	int i;
 
-	if (!(adapter->flags & IXGBE_FLAG_DCA_ENABLED))
-		return;
-
 	/* always use CB2 mode, difference is masked in the CB driver */
-	IXGBE_WRITE_REG(&adapter->hw, IXGBE_DCA_CTRL, 2);
+	if (adapter->flags & IXGBE_FLAG_DCA_ENABLED)
+		IXGBE_WRITE_REG(&adapter->hw, IXGBE_DCA_CTRL,
+				IXGBE_DCA_CTRL_DCA_MODE_CB2);
+	else
+		IXGBE_WRITE_REG(&adapter->hw, IXGBE_DCA_CTRL,
+				IXGBE_DCA_CTRL_DCA_DISABLE);
 
 	for (i = 0; i < adapter->num_q_vectors; i++) {
 		adapter->q_vector[i]->cpu = -1;
@@ -1353,7 +1362,8 @@ static int __ixgbe_notify_dca(struct device *dev, void *data)
 			break;
 		if (dca_add_requester(dev) == 0) {
 			adapter->flags |= IXGBE_FLAG_DCA_ENABLED;
-			ixgbe_setup_dca(adapter);
+			IXGBE_WRITE_REG(&adapter->hw, IXGBE_DCA_CTRL,
+					IXGBE_DCA_CTRL_DCA_MODE_CB2);
 			break;
 		}
 		/* Fall Through since DCA is disabled. */
@@ -1361,7 +1371,8 @@ static int __ixgbe_notify_dca(struct device *dev, void *data)
 		if (adapter->flags & IXGBE_FLAG_DCA_ENABLED) {
 			dca_remove_requester(dev);
 			adapter->flags &= ~IXGBE_FLAG_DCA_ENABLED;
-			IXGBE_WRITE_REG(&adapter->hw, IXGBE_DCA_CTRL, 1);
+			IXGBE_WRITE_REG(&adapter->hw, IXGBE_DCA_CTRL,
+					IXGBE_DCA_CTRL_DCA_DISABLE);
 		}
 		break;
 	}
@@ -2509,6 +2520,7 @@ static void ixgbe_check_sfp_event(struct ixgbe_adapter *adapter, u32 eicr)
 		IXGBE_WRITE_REG(hw, IXGBE_EICR, eicr_mask);
 		if (!test_bit(__IXGBE_DOWN, &adapter->state)) {
 			adapter->flags2 |= IXGBE_FLAG2_SFP_NEEDS_RESET;
+			adapter->sfp_poll_time = 0;
 			ixgbe_service_event_schedule(adapter);
 		}
 	}
@@ -3788,8 +3800,6 @@ static void ixgbe_setup_rdrxctl(struct ixgbe_adapter *adapter)
 	u32 rdrxctl = IXGBE_READ_REG(hw, IXGBE_RDRXCTL);
 
 	switch (hw->mac.type) {
-	case ixgbe_mac_X550:
-	case ixgbe_mac_X550EM_x:
 	case ixgbe_mac_82598EB:
 		/*
 		 * For VMDq support of different descriptor types or
@@ -3803,6 +3813,11 @@ static void ixgbe_setup_rdrxctl(struct ixgbe_adapter *adapter)
 		 */
 		rdrxctl |= IXGBE_RDRXCTL_MVMEN;
 		break;
+	case ixgbe_mac_X550:
+	case ixgbe_mac_X550EM_x:
+		if (adapter->num_vfs)
+			rdrxctl |= IXGBE_RDRXCTL_PSP;
+		/* fall through for older HW */
 	case ixgbe_mac_82599EB:
 	case ixgbe_mac_X540:
 		/* Disable RSC for ACK packets */
@@ -4778,6 +4793,12 @@ static void ixgbe_configure(struct ixgbe_adapter *adapter)
 		break;
 	}
 
+#ifdef CONFIG_IXGBE_DCA
+	/* configure DCA */
+	if (adapter->flags & IXGBE_FLAG_DCA_CAPABLE)
+		ixgbe_setup_dca(adapter);
+#endif /* CONFIG_IXGBE_DCA */
+
 #ifdef IXGBE_FCOE
 	/* configure FCoE L2 filters, redirection table, and Rx control */
 	ixgbe_configure_fcoe(adapter);
@@ -4804,6 +4825,7 @@ static void ixgbe_sfp_link_config(struct ixgbe_adapter *adapter)
 		adapter->flags2 |= IXGBE_FLAG2_SEARCH_FOR_SFP;
 
 	adapter->flags2 |= IXGBE_FLAG2_SFP_NEEDS_RESET;
+	adapter->sfp_poll_time = 0;
 }
 
 /**
@@ -4894,9 +4916,6 @@ static void ixgbe_setup_gpie(struct ixgbe_adapter *adapter)
 		case ixgbe_mac_82599EB:
 			gpie |= IXGBE_SDP0_GPIEN_8259X;
 			break;
-		case ixgbe_mac_X540:
-			gpie |= IXGBE_EIMS_TS;
-			break;
 		default:
 			break;
 		}
@@ -5237,11 +5256,6 @@ void ixgbe_down(struct ixgbe_adapter *adapter)
 
 	ixgbe_clean_all_tx_rings(adapter);
 	ixgbe_clean_all_rx_rings(adapter);
-
-#ifdef CONFIG_IXGBE_DCA
-	/* since we reset the hardware DCA settings were cleared */
-	ixgbe_setup_dca(adapter);
-#endif
 }
 
 /**
@@ -6709,10 +6723,16 @@ static void ixgbe_sfp_detection_subtask(struct ixgbe_adapter *adapter)
 	    !(adapter->flags2 & IXGBE_FLAG2_SFP_NEEDS_RESET))
 		return;
 
+	if (adapter->sfp_poll_time &&
+	    time_after(adapter->sfp_poll_time, jiffies))
+		return; /* If not yet time to poll for SFP */
+
 	/* someone else is in init, wait until next service event */
 	if (test_and_set_bit(__IXGBE_IN_SFP_INIT, &adapter->state))
 		return;
 
+	adapter->sfp_poll_time = jiffies + IXGBE_SFP_POLL_JIFFIES - 1;
+
 	err = hw->phy.ops.identify_sfp(hw);
 	if (err == IXGBE_ERR_SFP_NOT_SUPPORTED)
 		goto sfp_out;
@@ -9024,7 +9044,8 @@ static void ixgbe_remove(struct pci_dev *pdev)
 	if (adapter->flags & IXGBE_FLAG_DCA_ENABLED) {
 		adapter->flags &= ~IXGBE_FLAG_DCA_ENABLED;
 		dca_remove_requester(&pdev->dev);
-		IXGBE_WRITE_REG(&adapter->hw, IXGBE_DCA_CTRL, 1);
+		IXGBE_WRITE_REG(&adapter->hw, IXGBE_DCA_CTRL,
+				IXGBE_DCA_CTRL_DCA_DISABLE);
 	}
 
 #endif

drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c

@@ -1230,7 +1230,7 @@ s32 ixgbe_identify_sfp_module_generic(struct ixgbe_hw *hw)
 			hw->phy.sfp_type = ixgbe_sfp_type_lr;
 		else
 			hw->phy.sfp_type = ixgbe_sfp_type_unknown;
-	} else if (hw->mac.type == ixgbe_mac_82599EB) {
+	} else {
 		if (cable_tech & IXGBE_SFF_DA_PASSIVE_CABLE) {
 			if (hw->bus.lan_id == 0)
 				hw->phy.sfp_type =
@@ -1730,6 +1730,21 @@ s32 ixgbe_write_i2c_eeprom_generic(struct ixgbe_hw *hw, u8 byte_offset,
 					  eeprom_data);
 }
 
+/**
+ * ixgbe_is_sfp_probe - Returns true if SFP is being detected
+ * @hw: pointer to hardware structure
+ * @offset: eeprom offset to be read
+ * @addr: I2C address to be read
+ */
+static bool ixgbe_is_sfp_probe(struct ixgbe_hw *hw, u8 offset, u8 addr)
+{
+	if (addr == IXGBE_I2C_EEPROM_DEV_ADDR &&
+	    offset == IXGBE_SFF_IDENTIFIER &&
+	    hw->phy.sfp_type == ixgbe_sfp_type_not_present)
+		return true;
+	return false;
+}
+
 /**
  *  ixgbe_read_i2c_byte_generic_int - Reads 8 bit word over I2C
  *  @hw: pointer to hardware structure
@@ -1749,6 +1764,9 @@ static s32 ixgbe_read_i2c_byte_generic_int(struct ixgbe_hw *hw, u8 byte_offset,
 	u32 swfw_mask = hw->phy.phy_semaphore_mask;
 	bool nack = true;
 
+	if (ixgbe_is_sfp_probe(hw, byte_offset, dev_addr))
+		max_retry = IXGBE_SFP_DETECT_RETRIES;
+
 	*data = 0;
 
 	do {
@@ -2026,6 +2044,7 @@ static s32 ixgbe_clock_in_i2c_byte(struct ixgbe_hw *hw, u8 *data)
 	s32 i;
 	bool bit = false;
 
+	*data = 0;
 	for (i = 7; i >= 0; i--) {
 		ixgbe_clock_in_i2c_bit(hw, &bit);
 		*data |= bit << i;

drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h

@@ -66,6 +66,9 @@
 #define IXGBE_SFF_1GBASET_CAPABLE		0x8
 #define IXGBE_SFF_10GBASESR_CAPABLE		0x10
 #define IXGBE_SFF_10GBASELR_CAPABLE		0x20
+#define IXGBE_SFF_SOFT_RS_SELECT_MASK		0x8
+#define IXGBE_SFF_SOFT_RS_SELECT_10G		0x8
+#define IXGBE_SFF_SOFT_RS_SELECT_1G		0x0
 #define IXGBE_SFF_ADDRESSING_MODE		0x4
 #define IXGBE_SFF_QSFP_DA_ACTIVE_CABLE		0x1
 #define IXGBE_SFF_QSFP_DA_PASSIVE_CABLE		0x8
@@ -78,9 +81,29 @@
 #define IXGBE_I2C_EEPROM_STATUS_FAIL		0x2
 #define IXGBE_I2C_EEPROM_STATUS_IN_PROGRESS	0x3
 #define IXGBE_CS4227				0xBE    /* CS4227 address */
-#define IXGBE_CS4227_SPARE24_LSB		0x12B0  /* Reg to program EDC */
+#define IXGBE_CS4227_SCRATCH			2
+#define IXGBE_CS4227_RESET_PENDING		0x1357
+#define IXGBE_CS4227_RESET_COMPLETE		0x5AA5
+#define IXGBE_CS4227_RETRIES			15
+#define IXGBE_CS4227_EFUSE_STATUS		0x0181
+#define IXGBE_CS4227_LINE_SPARE22_MSB		0x12AD	/* Reg to set speed */
+#define IXGBE_CS4227_LINE_SPARE24_LSB		0x12B0	/* Reg to set EDC */
+#define IXGBE_CS4227_HOST_SPARE22_MSB		0x1AAD	/* Reg to set speed */
+#define IXGBE_CS4227_HOST_SPARE24_LSB		0x1AB0	/* Reg to program EDC */
+#define IXGBE_CS4227_EEPROM_STATUS		0x5001
+#define IXGBE_CS4227_EEPROM_LOAD_OK		0x0001
+#define IXGBE_CS4227_SPEED_1G			0x8000
+#define IXGBE_CS4227_SPEED_10G			0
 #define IXGBE_CS4227_EDC_MODE_CX1		0x0002
 #define IXGBE_CS4227_EDC_MODE_SR		0x0004
+#define IXGBE_CS4227_EDC_MODE_DIAG		0x0008
+#define IXGBE_CS4227_RESET_HOLD			500	/* microseconds */
+#define IXGBE_CS4227_RESET_DELAY		500	/* milliseconds */
+#define IXGBE_CS4227_CHECK_DELAY		30	/* milliseconds */
+#define IXGBE_PE				0xE0	/* Port expander addr */
+#define IXGBE_PE_OUTPUT				1	/* Output reg offset */
+#define IXGBE_PE_CONFIG				3	/* Config reg offset */
+#define IXGBE_PE_BIT1				(1 << 1)
 
 /* Flow control defines */
 #define IXGBE_TAF_SYM_PAUSE                  0x400
@@ -109,6 +132,8 @@
 #define IXGBE_I2C_T_SU_STO  4
 #define IXGBE_I2C_T_BUF     5
 
+#define IXGBE_SFP_DETECT_RETRIES	2
+
 #define IXGBE_TN_LASI_STATUS_REG        0x9005
 #define IXGBE_TN_LASI_STATUS_TEMP_ALARM 0x0008
 

drivers/net/ethernet/intel/ixgbe/ixgbe_type.h

@@ -1193,6 +1193,7 @@ struct ixgbe_thermal_sensor_data {
 /* RDRXCTL Bit Masks */
 #define IXGBE_RDRXCTL_RDMTS_1_2     0x00000000 /* Rx Desc Min Threshold Size */
 #define IXGBE_RDRXCTL_CRCSTRIP      0x00000002 /* CRC Strip */
+#define IXGBE_RDRXCTL_PSP           0x00000004 /* Pad small packet */
 #define IXGBE_RDRXCTL_MVMEN         0x00000020
 #define IXGBE_RDRXCTL_DMAIDONE      0x00000008 /* DMA init cycle done */
 #define IXGBE_RDRXCTL_AGGDIS        0x00010000 /* Aggregation disable */
@@ -1949,6 +1950,7 @@ enum {
 #define IXGBE_GSSR_SW_MNG_SM		0x0400
 #define IXGBE_GSSR_SHARED_I2C_SM	0x1806 /* Wait for both phys & I2Cs */
 #define IXGBE_GSSR_I2C_MASK		0x1800
+#define IXGBE_GSSR_NVM_PHY_MASK		0xF
 
 /* FW Status register bitmask */
 #define IXGBE_FWSTS_FWRI    0x00000200 /* Firmware Reset Indication */
@@ -3256,9 +3258,11 @@ struct ixgbe_mac_operations {
 	void (*flap_tx_laser)(struct ixgbe_hw *);
 	void (*stop_link_on_d3)(struct ixgbe_hw *);
 	s32 (*setup_link)(struct ixgbe_hw *, ixgbe_link_speed, bool);
+	s32 (*setup_mac_link)(struct ixgbe_hw *, ixgbe_link_speed, bool);
 	s32 (*check_link)(struct ixgbe_hw *, ixgbe_link_speed *, bool *, bool);
 	s32 (*get_link_capabilities)(struct ixgbe_hw *, ixgbe_link_speed *,
 				     bool *);
+	void (*set_rate_select_speed)(struct ixgbe_hw *, ixgbe_link_speed);
 
 	/* Packet Buffer Manipulation */
 	void (*set_rxpba)(struct ixgbe_hw *, int, u32, int);

drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c

@@ -567,19 +567,25 @@ static s32 ixgbe_poll_flash_update_done_X540(struct ixgbe_hw *hw)
  **/
 s32 ixgbe_acquire_swfw_sync_X540(struct ixgbe_hw *hw, u32 mask)
 {
-	u32 swfw_sync;
-	u32 swmask = mask;
-	u32 fwmask = mask << 5;
-	u32 hwmask = 0;
+	u32 swmask = mask & IXGBE_GSSR_NVM_PHY_MASK;
+	u32 swi2c_mask = mask & IXGBE_GSSR_I2C_MASK;
+	u32 fwmask = swmask << 5;
 	u32 timeout = 200;
+	u32 hwmask = 0;
+	u32 swfw_sync;
 	u32 i;
 
-	if (swmask == IXGBE_GSSR_EEP_SM)
+	if (swmask & IXGBE_GSSR_EEP_SM)
 		hwmask = IXGBE_GSSR_FLASH_SM;
 
+	/* SW only mask does not have FW bit pair */
+	if (mask & IXGBE_GSSR_SW_MNG_SM)
+		swmask |= IXGBE_GSSR_SW_MNG_SM;
+
+	swmask |= swi2c_mask;
+	fwmask |= swi2c_mask << 2;
 	for (i = 0; i < timeout; i++) {
-		/*
-		 * SW NVM semaphore bit is used for access to all
+		/* SW NVM semaphore bit is used for access to all
 		 * SW_FW_SYNC bits (not just NVM)
 		 */
 		if (ixgbe_get_swfw_sync_semaphore(hw))
@@ -590,39 +596,56 @@ s32 ixgbe_acquire_swfw_sync_X540(struct ixgbe_hw *hw, u32 mask)
 			swfw_sync |= swmask;
 			IXGBE_WRITE_REG(hw, IXGBE_SWFW_SYNC(hw), swfw_sync);
 			ixgbe_release_swfw_sync_semaphore(hw);
-			break;
-		} else {
-			/*
-			 * Firmware currently using resource (fwmask),
-			 * hardware currently using resource (hwmask),
-			 * or other software thread currently using
-			 * resource (swmask)
+			usleep_range(5000, 6000);
+			return 0;
+		}
+		/* Firmware currently using resource (fwmask), hardware
+		 * currently using resource (hwmask), or other software
+		 * thread currently using resource (swmask)
 		 */
 		ixgbe_release_swfw_sync_semaphore(hw);
 		usleep_range(5000, 10000);
 	}
+
+	/* Failed to get SW only semaphore */
+	if (swmask == IXGBE_GSSR_SW_MNG_SM) {
+		hw_dbg(hw, "Failed to get SW only semaphore\n");
+		return IXGBE_ERR_SWFW_SYNC;
 	}
 
-	/*
-	 * If the resource is not released by the FW/HW the SW can assume that
-	 * the FW/HW malfunctions. In that case the SW should sets the
-	 * SW bit(s) of the requested resource(s) while ignoring the
-	 * corresponding FW/HW bits in the SW_FW_SYNC register.
+	/* If the resource is not released by the FW/HW the SW can assume that
+	 * the FW/HW malfunctions. In that case the SW should set the SW bit(s)
+	 * of the requested resource(s) while ignoring the corresponding FW/HW
+	 * bits in the SW_FW_SYNC register.
 	 */
-	if (i >= timeout) {
-		swfw_sync = IXGBE_READ_REG(hw, IXGBE_SWFW_SYNC(hw));
-		if (swfw_sync & (fwmask | hwmask)) {
 	if (ixgbe_get_swfw_sync_semaphore(hw))
 		return IXGBE_ERR_SWFW_SYNC;
-
+	swfw_sync = IXGBE_READ_REG(hw, IXGBE_SWFW_SYNC(hw));
+	if (swfw_sync & (fwmask | hwmask)) {
 		swfw_sync |= swmask;
 		IXGBE_WRITE_REG(hw, IXGBE_SWFW_SYNC(hw), swfw_sync);
 		ixgbe_release_swfw_sync_semaphore(hw);
+		usleep_range(5000, 6000);
+		return 0;
 	}
+	/* If the resource is not released by other SW the SW can assume that
+	 * the other SW malfunctions. In that case the SW should clear all SW
+	 * flags that it does not own and then repeat the whole process once
+	 * again.
+	 */
+	if (swfw_sync & swmask) {
+		u32 rmask = IXGBE_GSSR_EEP_SM | IXGBE_GSSR_PHY0_SM |
+			    IXGBE_GSSR_PHY1_SM | IXGBE_GSSR_MAC_CSR_SM;
+
+		if (swi2c_mask)
+			rmask |= IXGBE_GSSR_I2C_MASK;
+		ixgbe_release_swfw_sync_X540(hw, rmask);
+		ixgbe_release_swfw_sync_semaphore(hw);
+		return IXGBE_ERR_SWFW_SYNC;
 	}
+	ixgbe_release_swfw_sync_semaphore(hw);
 
-	usleep_range(5000, 10000);
-	return 0;
+	return IXGBE_ERR_SWFW_SYNC;
 }
 
 /**
@@ -635,9 +658,11 @@ s32 ixgbe_acquire_swfw_sync_X540(struct ixgbe_hw *hw, u32 mask)
  **/
 void ixgbe_release_swfw_sync_X540(struct ixgbe_hw *hw, u32 mask)
 {
+	u32 swmask = mask & (IXGBE_GSSR_NVM_PHY_MASK | IXGBE_GSSR_SW_MNG_SM);
 	u32 swfw_sync;
-	u32 swmask = mask;
 
+	if (mask & IXGBE_GSSR_I2C_MASK)
+		swmask |= mask & IXGBE_GSSR_I2C_MASK;
 	ixgbe_get_swfw_sync_semaphore(hw);
 
 	swfw_sync = IXGBE_READ_REG(hw, IXGBE_SWFW_SYNC(hw));
@@ -645,7 +670,7 @@ void ixgbe_release_swfw_sync_X540(struct ixgbe_hw *hw, u32 mask)
 	IXGBE_WRITE_REG(hw, IXGBE_SWFW_SYNC(hw), swfw_sync);
 
 	ixgbe_release_swfw_sync_semaphore(hw);
-	usleep_range(5000, 10000);
+	usleep_range(5000, 6000);
 }
 
 /**
@@ -686,6 +711,11 @@ static s32 ixgbe_get_swfw_sync_semaphore(struct ixgbe_hw *hw)
 		usleep_range(50, 100);
 	}
 
+	/* Release semaphores and return error if SW NVM semaphore
+	 * was not granted because we do not have access to the EEPROM
+	 */
+	hw_dbg(hw, "REGSMP Software NVM semaphore not granted\n");
+	ixgbe_release_swfw_sync_semaphore(hw);
 	return IXGBE_ERR_EEPROM;
 }