ARM: SAMSUNG: Move common save/restore helpers to separate file

To separate legacy PM code from generic helpers, this patch moves the
generic register save/restore helpers to a new file called pm-common.c
that is compiled always when CONFIG_PM_SLEEP is enabled, to allow
platforms that do not want to use the legacy PM code use the generic
helpers.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

arch/arm/plat-samsung/Makefile

@@ -47,6 +47,7 @@ obj-$(CONFIG_SAMSUNG_DMADEV)	+= dma-ops.o
 
 # PM support
 
+obj-$(CONFIG_PM_SLEEP)		+= pm-common.o
 obj-$(CONFIG_SAMSUNG_PM)	+= pm.o
 obj-$(CONFIG_SAMSUNG_PM_GPIO)	+= pm-gpio.o
 obj-$(CONFIG_SAMSUNG_PM_CHECK)	+= pm-check.o

arch/arm/plat-samsung/include/plat/pm-common.h

@@ -13,6 +13,32 @@
 #ifndef __PLAT_SAMSUNG_PM_COMMON_H
 #define __PLAT_SAMSUNG_PM_COMMON_H __FILE__
 
+#include <linux/irq.h>
+
+/* sleep save info */
+
+/**
+ * struct sleep_save - save information for shared peripherals.
+ * @reg: Pointer to the register to save.
+ * @val: Holder for the value saved from reg.
+ *
+ * This describes a list of registers which is used by the pm core and
+ * other subsystem to save and restore register values over suspend.
+ */
+struct sleep_save {
+	void __iomem	*reg;
+	unsigned long	val;
+};
+
+#define SAVE_ITEM(x) \
+	{ .reg = (x) }
+
+/* helper functions to save/restore lists of registers. */
+
+extern void s3c_pm_do_save(struct sleep_save *ptr, int count);
+extern void s3c_pm_do_restore(const struct sleep_save *ptr, int count);
+extern void s3c_pm_do_restore_core(const struct sleep_save *ptr, int count);
+
 /* PM debug functions */
 
 /**

arch/arm/plat-samsung/include/plat/pm.h

@@ -15,7 +15,6 @@
  * management
 */
 
-#include <linux/irq.h>
 #include <plat/pm-common.h>
 
 struct device;
@@ -59,30 +58,6 @@ extern unsigned long s3c_pm_flags;
 
 extern int s3c2410_cpu_suspend(unsigned long);
 
-/* sleep save info */
-
-/**
- * struct sleep_save - save information for shared peripherals.
- * @reg: Pointer to the register to save.
- * @val: Holder for the value saved from reg.
- *
- * This describes a list of registers which is used by the pm core and
- * other subsystem to save and restore register values over suspend.
- */
-struct sleep_save {
-	void __iomem	*reg;
-	unsigned long	val;
-};
-
-#define SAVE_ITEM(x) \
-	{ .reg = (x) }
-
-/* helper functions to save/restore lists of registers. */
-
-extern void s3c_pm_do_save(struct sleep_save *ptr, int count);
-extern void s3c_pm_do_restore(const struct sleep_save *ptr, int count);
-extern void s3c_pm_do_restore_core(const struct sleep_save *ptr, int count);
-
 #ifdef CONFIG_SAMSUNG_PM
 extern int s3c_irq_wake(struct irq_data *data, unsigned int state);
 extern int s3c_irqext_wake(struct irq_data *data, unsigned int state);

arch/arm/plat-samsung/pm-common.c

+/*
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ *	Tomasz Figa <t.figa@samsung.com>
+ * Copyright (C) 2008 Openmoko, Inc.
+ * Copyright (C) 2004-2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ *
+ * Samsung common power management helper functions.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/io.h>
+#include <linux/kernel.h>
+
+#include <plat/pm-common.h>
+
+/* helper functions to save and restore register state */
+
+/**
+ * s3c_pm_do_save() - save a set of registers for restoration on resume.
+ * @ptr: Pointer to an array of registers.
+ * @count: Size of the ptr array.
+ *
+ * Run through the list of registers given, saving their contents in the
+ * array for later restoration when we wakeup.
+ */
+void s3c_pm_do_save(struct sleep_save *ptr, int count)
+{
+	for (; count > 0; count--, ptr++) {
+		ptr->val = __raw_readl(ptr->reg);
+		S3C_PMDBG("saved %p value %08lx\n", ptr->reg, ptr->val);
+	}
+}
+
+/**
+ * s3c_pm_do_restore() - restore register values from the save list.
+ * @ptr: Pointer to an array of registers.
+ * @count: Size of the ptr array.
+ *
+ * Restore the register values saved from s3c_pm_do_save().
+ *
+ * Note, we do not use S3C_PMDBG() in here, as the system may not have
+ * restore the UARTs state yet
+*/
+
+void s3c_pm_do_restore(const struct sleep_save *ptr, int count)
+{
+	for (; count > 0; count--, ptr++) {
+		pr_debug("restore %p (restore %08lx, was %08x)\n",
+				ptr->reg, ptr->val, __raw_readl(ptr->reg));
+
+		__raw_writel(ptr->val, ptr->reg);
+	}
+}
+
+/**
+ * s3c_pm_do_restore_core() - early restore register values from save list.
+ *
+ * This is similar to s3c_pm_do_restore() except we try and minimise the
+ * side effects of the function in case registers that hardware might need
+ * to work has been restored.
+ *
+ * WARNING: Do not put any debug in here that may effect memory or use
+ * peripherals, as things may be changing!
+*/
+
+void s3c_pm_do_restore_core(const struct sleep_save *ptr, int count)
+{
+	for (; count > 0; count--, ptr++)
+		__raw_writel(ptr->val, ptr->reg);
+}

arch/arm/plat-samsung/pm.c

@@ -66,62 +66,6 @@ int s3c_irqext_wake(struct irq_data *data, unsigned int state)
 	return 0;
 }
 
-/* helper functions to save and restore register state */
-
-/**
- * s3c_pm_do_save() - save a set of registers for restoration on resume.
- * @ptr: Pointer to an array of registers.
- * @count: Size of the ptr array.
- *
- * Run through the list of registers given, saving their contents in the
- * array for later restoration when we wakeup.
- */
-void s3c_pm_do_save(struct sleep_save *ptr, int count)
-{
-	for (; count > 0; count--, ptr++) {
-		ptr->val = __raw_readl(ptr->reg);
-		S3C_PMDBG("saved %p value %08lx\n", ptr->reg, ptr->val);
-	}
-}
-
-/**
- * s3c_pm_do_restore() - restore register values from the save list.
- * @ptr: Pointer to an array of registers.
- * @count: Size of the ptr array.
- *
- * Restore the register values saved from s3c_pm_do_save().
- *
- * Note, we do not use S3C_PMDBG() in here, as the system may not have
- * restore the UARTs state yet
-*/
-
-void s3c_pm_do_restore(const struct sleep_save *ptr, int count)
-{
-	for (; count > 0; count--, ptr++) {
-		printk(KERN_DEBUG "restore %p (restore %08lx, was %08x)\n",
-		       ptr->reg, ptr->val, __raw_readl(ptr->reg));
-
-		__raw_writel(ptr->val, ptr->reg);
-	}
-}
-
-/**
- * s3c_pm_do_restore_core() - early restore register values from save list.
- *
- * This is similar to s3c_pm_do_restore() except we try and minimise the
- * side effects of the function in case registers that hardware might need
- * to work has been restored.
- *
- * WARNING: Do not put any debug in here that may effect memory or use
- * peripherals, as things may be changing!
-*/
-
-void s3c_pm_do_restore_core(const struct sleep_save *ptr, int count)
-{
-	for (; count > 0; count--, ptr++)
-		__raw_writel(ptr->val, ptr->reg);
-}
-
 /* s3c2410_pm_show_resume_irqs
  *
  * print any IRQs asserted at resume time (ie, we woke from)