Merge branch 'usbnet-speed'

Grant Grundler says:

====================
usbnet: speed reporting for devices without MDIO

This series introduces support for USB network devices that report
speed as a part of their protocol, not emulating an MII to be accessed
over MDIO.

v2: rebased on recent upstream changes
v3: incorporated hints on naming and comments
v4: fix misplaced hunks; reword some commit messages;
    add same change for cdc_ether
v4-repost: added "net-next" to subject and Andrew Lunn's Reviewed-by

I'm reposting Oliver Neukum's <oneukum@suse.com> patch series with
fix ups for "misplaced hunks" (landed in the wrong patches).
Please fixup the "author" if "git am" fails to attribute the
patches 1-3 (of 4) to Oliver.

I've tested v4 series with "5.12-rc3+" kernel on Intel NUC6i5SYB
and + Sabrent NT-S25G. Google Pixelbook Go (chromeos-4.4 kernel)
+ Alpha Network AUE2500C were connected directly to the NT-S25G
to get 2.5Gbps link rate:
Settings for enx002427880815:
        Supported ports: [  ]
        Supported link modes:   Not reported
        Supported pause frame use: No
        Supports auto-negotiation: No
        Supported FEC modes: Not reported
        Advertised link modes:  Not reported
        Advertised pause frame use: No
        Advertised auto-negotiation: No
        Advertised FEC modes: Not reported
        Speed: 2500Mb/s
        Duplex: Half
        Auto-negotiation: off
        Port: Twisted Pair
        PHYAD: 0
        Transceiver: internal
        MDI-X: Unknown
        Current message level: 0x00000007 (7)
                               drv probe link
        Link detected: yes

"Duplex" is a lie since we get no information about it.

I expect "Auto-Negotiation" is always true for cdc_ncm and
cdc_ether devices and perhaps someone knows offhand how
to have ethtool report "true" instead.

But this is good step in the right direction.

base-commit: 1c273e10
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/usb/asix_devices.c

@@ -125,8 +125,8 @@ static const struct ethtool_ops ax88172_ethtool_ops = {
 	.get_eeprom		= asix_get_eeprom,
 	.set_eeprom		= asix_set_eeprom,
 	.nway_reset		= usbnet_nway_reset,
-	.get_link_ksettings	= usbnet_get_link_ksettings,
-	.set_link_ksettings	= usbnet_set_link_ksettings,
+	.get_link_ksettings	= usbnet_get_link_ksettings_mii,
+	.set_link_ksettings	= usbnet_set_link_ksettings_mii,
 };
 
 static void ax88172_set_multicast(struct net_device *net)
@@ -291,8 +291,8 @@ static const struct ethtool_ops ax88772_ethtool_ops = {
 	.get_eeprom		= asix_get_eeprom,
 	.set_eeprom		= asix_set_eeprom,
 	.nway_reset		= usbnet_nway_reset,
-	.get_link_ksettings	= usbnet_get_link_ksettings,
-	.set_link_ksettings	= usbnet_set_link_ksettings,
+	.get_link_ksettings	= usbnet_get_link_ksettings_mii,
+	.set_link_ksettings	= usbnet_set_link_ksettings_mii,
 };
 
 static int ax88772_link_reset(struct usbnet *dev)
@@ -782,8 +782,8 @@ static const struct ethtool_ops ax88178_ethtool_ops = {
 	.get_eeprom		= asix_get_eeprom,
 	.set_eeprom		= asix_set_eeprom,
 	.nway_reset		= usbnet_nway_reset,
-	.get_link_ksettings	= usbnet_get_link_ksettings,
-	.set_link_ksettings	= usbnet_set_link_ksettings,
+	.get_link_ksettings	= usbnet_get_link_ksettings_mii,
+	.set_link_ksettings	= usbnet_set_link_ksettings_mii,
 };
 
 static int marvell_phy_init(struct usbnet *dev)

drivers/net/usb/cdc_ether.c

@@ -92,6 +92,18 @@ void usbnet_cdc_update_filter(struct usbnet *dev)
 }
 EXPORT_SYMBOL_GPL(usbnet_cdc_update_filter);
 
+/* We need to override usbnet_*_link_ksettings in bind() */
+static const struct ethtool_ops cdc_ether_ethtool_ops = {
+	.get_link		= usbnet_get_link,
+	.nway_reset		= usbnet_nway_reset,
+	.get_drvinfo		= usbnet_get_drvinfo,
+	.get_msglevel		= usbnet_get_msglevel,
+	.set_msglevel		= usbnet_set_msglevel,
+	.get_ts_info		= ethtool_op_get_ts_info,
+	.get_link_ksettings	= usbnet_get_link_ksettings_internal,
+	.set_link_ksettings	= NULL,
+};
+
 /* probes control interface, claims data interface, collects the bulk
  * endpoints, activates data interface (if needed), maybe sets MTU.
  * all pure cdc, except for certain firmware workarounds, and knowing
@@ -310,6 +322,9 @@ int usbnet_generic_cdc_bind(struct usbnet *dev, struct usb_interface *intf)
 		return -ENODEV;
 	}
 
+	/* override ethtool_ops */
+	dev->net->ethtool_ops = &cdc_ether_ethtool_ops;
+
 	return 0;
 
 bad_desc:
@@ -379,12 +394,10 @@ EXPORT_SYMBOL_GPL(usbnet_cdc_unbind);
  * (by Brad Hards) talked with, with more functionality.
  */
 
-static void dumpspeed(struct usbnet *dev, __le32 *speeds)
+static void speed_change(struct usbnet *dev, __le32 *speeds)
 {
-	netif_info(dev, timer, dev->net,
-		   "link speeds: %u kbps up, %u kbps down\n",
-		   __le32_to_cpu(speeds[0]) / 1000,
-		   __le32_to_cpu(speeds[1]) / 1000);
+	dev->tx_speed = __le32_to_cpu(speeds[0]);
+	dev->rx_speed = __le32_to_cpu(speeds[1]);
 }
 
 void usbnet_cdc_status(struct usbnet *dev, struct urb *urb)
@@ -396,7 +409,7 @@ void usbnet_cdc_status(struct usbnet *dev, struct urb *urb)
 
 	/* SPEED_CHANGE can get split into two 8-byte packets */
 	if (test_and_clear_bit(EVENT_STS_SPLIT, &dev->flags)) {
-		dumpspeed(dev, (__le32 *) urb->transfer_buffer);
+		speed_change(dev, (__le32 *) urb->transfer_buffer);
 		return;
 	}
 
@@ -413,7 +426,7 @@ void usbnet_cdc_status(struct usbnet *dev, struct urb *urb)
 		if (urb->actual_length != (sizeof(*event) + 8))
 			set_bit(EVENT_STS_SPLIT, &dev->flags);
 		else
-			dumpspeed(dev, (__le32 *) &event[1]);
+			speed_change(dev, (__le32 *) &event[1]);
 		break;
 	/* USB_CDC_NOTIFY_RESPONSE_AVAILABLE can happen too (e.g. RNDIS),
 	 * but there are no standard formats for the response data.

drivers/net/usb/cdc_ncm.c

@@ -142,8 +142,8 @@ static const struct ethtool_ops cdc_ncm_ethtool_ops = {
 	.get_sset_count		= cdc_ncm_get_sset_count,
 	.get_strings		= cdc_ncm_get_strings,
 	.get_ethtool_stats	= cdc_ncm_get_ethtool_stats,
-	.get_link_ksettings      = usbnet_get_link_ksettings,
-	.set_link_ksettings      = usbnet_set_link_ksettings,
+	.get_link_ksettings	= usbnet_get_link_ksettings_internal,
+	.set_link_ksettings	= NULL,
 };
 
 static u32 cdc_ncm_check_rx_max(struct usbnet *dev, u32 new_rx)
@@ -1825,33 +1825,9 @@ static void
 cdc_ncm_speed_change(struct usbnet *dev,
 		     struct usb_cdc_speed_change *data)
 {
-	uint32_t rx_speed = le32_to_cpu(data->DLBitRRate);
-	uint32_t tx_speed = le32_to_cpu(data->ULBitRate);
-
-	/* if the speed hasn't changed, don't report it.
-	 * RTL8156 shipped before 2021 sends notification about every 32ms.
-	 */
-	if (dev->rx_speed == rx_speed && dev->tx_speed == tx_speed)
-		return;
-
-	dev->rx_speed = rx_speed;
-	dev->tx_speed = tx_speed;
-
-	/*
-	 * Currently the USB-NET API does not support reporting the actual
-	 * device speed. Do print it instead.
-	 */
-	if ((tx_speed > 1000000) && (rx_speed > 1000000)) {
-		netif_info(dev, link, dev->net,
-			   "%u mbit/s downlink %u mbit/s uplink\n",
-			   (unsigned int)(rx_speed / 1000000U),
-			   (unsigned int)(tx_speed / 1000000U));
-	} else {
-		netif_info(dev, link, dev->net,
-			   "%u kbit/s downlink %u kbit/s uplink\n",
-			   (unsigned int)(rx_speed / 1000U),
-			   (unsigned int)(tx_speed / 1000U));
-	}
+	/* RTL8156 shipped before 2021 sends notification about every 32ms. */
+	dev->rx_speed = le32_to_cpu(data->DLBitRRate);
+	dev->tx_speed = le32_to_cpu(data->ULBitRate);
 }
 
 static void cdc_ncm_status(struct usbnet *dev, struct urb *urb)
@@ -1877,6 +1853,9 @@ static void cdc_ncm_status(struct usbnet *dev, struct urb *urb)
 		 * USB_CDC_NOTIFY_NETWORK_CONNECTION notification shall be
 		 * sent by device after USB_CDC_NOTIFY_SPEED_CHANGE.
 		 */
+		/* RTL8156 shipped before 2021 sends notification about
+		 * every 32ms. Don't forward notification if state is same.
+		 */
 		if (netif_carrier_ok(dev->net) != !!event->wValue)
 			usbnet_link_change(dev, !!event->wValue, 0);
 		break;

drivers/net/usb/dm9601.c

@@ -282,8 +282,8 @@ static const struct ethtool_ops dm9601_ethtool_ops = {
 	.get_eeprom_len	= dm9601_get_eeprom_len,
 	.get_eeprom	= dm9601_get_eeprom,
 	.nway_reset	= usbnet_nway_reset,
-	.get_link_ksettings	= usbnet_get_link_ksettings,
-	.set_link_ksettings	= usbnet_set_link_ksettings,
+	.get_link_ksettings	= usbnet_get_link_ksettings_mii,
+	.set_link_ksettings	= usbnet_set_link_ksettings_mii,
 };
 
 static void dm9601_set_multicast(struct net_device *net)

drivers/net/usb/mcs7830.c

@@ -452,8 +452,8 @@ static const struct ethtool_ops mcs7830_ethtool_ops = {
 	.get_msglevel		= usbnet_get_msglevel,
 	.set_msglevel		= usbnet_set_msglevel,
 	.nway_reset		= usbnet_nway_reset,
-	.get_link_ksettings	= usbnet_get_link_ksettings,
-	.set_link_ksettings	= usbnet_set_link_ksettings,
+	.get_link_ksettings	= usbnet_get_link_ksettings_mii,
+	.set_link_ksettings	= usbnet_set_link_ksettings_mii,
 };
 
 static const struct net_device_ops mcs7830_netdev_ops = {

drivers/net/usb/sierra_net.c

@@ -629,8 +629,8 @@ static const struct ethtool_ops sierra_net_ethtool_ops = {
 	.get_msglevel = usbnet_get_msglevel,
 	.set_msglevel = usbnet_set_msglevel,
 	.nway_reset = usbnet_nway_reset,
-	.get_link_ksettings = usbnet_get_link_ksettings,
-	.set_link_ksettings = usbnet_set_link_ksettings,
+	.get_link_ksettings = usbnet_get_link_ksettings_mii,
+	.set_link_ksettings = usbnet_set_link_ksettings_mii,
 };
 
 static int sierra_net_get_fw_attr(struct usbnet *dev, u16 *datap)

drivers/net/usb/smsc75xx.c

@@ -741,8 +741,8 @@ static const struct ethtool_ops smsc75xx_ethtool_ops = {
 	.set_eeprom	= smsc75xx_ethtool_set_eeprom,
 	.get_wol	= smsc75xx_ethtool_get_wol,
 	.set_wol	= smsc75xx_ethtool_set_wol,
-	.get_link_ksettings	= usbnet_get_link_ksettings,
-	.set_link_ksettings	= usbnet_set_link_ksettings,
+	.get_link_ksettings	= usbnet_get_link_ksettings_mii,
+	.set_link_ksettings	= usbnet_set_link_ksettings_mii,
 };
 
 static int smsc75xx_ioctl(struct net_device *netdev, struct ifreq *rq, int cmd)

drivers/net/usb/sr9700.c

@@ -250,8 +250,8 @@ static const struct ethtool_ops sr9700_ethtool_ops = {
 	.get_eeprom_len	= sr9700_get_eeprom_len,
 	.get_eeprom	= sr9700_get_eeprom,
 	.nway_reset	= usbnet_nway_reset,
-	.get_link_ksettings	= usbnet_get_link_ksettings,
-	.set_link_ksettings	= usbnet_set_link_ksettings,
+	.get_link_ksettings	= usbnet_get_link_ksettings_mii,
+	.set_link_ksettings	= usbnet_set_link_ksettings_mii,
 };
 
 static void sr9700_set_multicast(struct net_device *netdev)

drivers/net/usb/sr9800.c

@@ -527,8 +527,8 @@ static const struct ethtool_ops sr9800_ethtool_ops = {
 	.get_eeprom_len	= sr_get_eeprom_len,
 	.get_eeprom	= sr_get_eeprom,
 	.nway_reset	= usbnet_nway_reset,
-	.get_link_ksettings	= usbnet_get_link_ksettings,
-	.set_link_ksettings	= usbnet_set_link_ksettings,
+	.get_link_ksettings	= usbnet_get_link_ksettings_mii,
+	.set_link_ksettings	= usbnet_set_link_ksettings_mii,
 };
 
 static int sr9800_link_reset(struct usbnet *dev)

drivers/net/usb/usbnet.c

@@ -944,7 +944,10 @@ EXPORT_SYMBOL_GPL(usbnet_open);
  * they'll probably want to use this base set.
  */
 
-int usbnet_get_link_ksettings(struct net_device *net,
+/* These methods are written on the assumption that the device
+ * uses MII
+ */
+int usbnet_get_link_ksettings_mii(struct net_device *net,
 			      struct ethtool_link_ksettings *cmd)
 {
 	struct usbnet *dev = netdev_priv(net);
@@ -956,9 +959,30 @@ int usbnet_get_link_ksettings(struct net_device *net,
 
 	return 0;
 }
-EXPORT_SYMBOL_GPL(usbnet_get_link_ksettings);
+EXPORT_SYMBOL_GPL(usbnet_get_link_ksettings_mii);
+
+int usbnet_get_link_ksettings_internal(struct net_device *net,
+					struct ethtool_link_ksettings *cmd)
+{
+	struct usbnet *dev = netdev_priv(net);
+
+	/* the assumption that speed is equal on tx and rx
+	 * is deeply engrained into the networking layer.
+	 * For wireless stuff it is not true.
+	 * We assume that rx_speed matters more.
+	 */
+	if (dev->rx_speed != SPEED_UNSET)
+		cmd->base.speed = dev->rx_speed / 1000000;
+	else if (dev->tx_speed != SPEED_UNSET)
+		cmd->base.speed = dev->tx_speed / 1000000;
+	else
+		cmd->base.speed = SPEED_UNKNOWN;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(usbnet_get_link_ksettings_internal);
 
-int usbnet_set_link_ksettings(struct net_device *net,
+int usbnet_set_link_ksettings_mii(struct net_device *net,
 			      const struct ethtool_link_ksettings *cmd)
 {
 	struct usbnet *dev = netdev_priv(net);
@@ -978,7 +1002,7 @@ int usbnet_set_link_ksettings(struct net_device *net,
 
 	return retval;
 }
-EXPORT_SYMBOL_GPL(usbnet_set_link_ksettings);
+EXPORT_SYMBOL_GPL(usbnet_set_link_ksettings_mii);
 
 u32 usbnet_get_link (struct net_device *net)
 {
@@ -1043,8 +1067,8 @@ static const struct ethtool_ops usbnet_ethtool_ops = {
 	.get_msglevel		= usbnet_get_msglevel,
 	.set_msglevel		= usbnet_set_msglevel,
 	.get_ts_info		= ethtool_op_get_ts_info,
-	.get_link_ksettings	= usbnet_get_link_ksettings,
-	.set_link_ksettings	= usbnet_set_link_ksettings,
+	.get_link_ksettings	= usbnet_get_link_ksettings_mii,
+	.set_link_ksettings	= usbnet_set_link_ksettings_mii,
 };
 
 /*-------------------------------------------------------------------------*/
@@ -1661,6 +1685,8 @@ usbnet_probe (struct usb_interface *udev, const struct usb_device_id *prod)
 	dev->intf = udev;
 	dev->driver_info = info;
 	dev->driver_name = name;
+	dev->rx_speed = SPEED_UNSET;
+	dev->tx_speed = SPEED_UNSET;
 
 	net->tstats = netdev_alloc_pcpu_stats(struct pcpu_sw_netstats);
 	if (!net->tstats)

include/linux/usb/usbnet.h

@@ -53,6 +53,9 @@ struct usbnet {
 	u32			hard_mtu;	/* count any extra framing */
 	size_t			rx_urb_size;	/* size for rx urbs */
 	struct mii_if_info	mii;
+	long			rx_speed;	/* If MII not used */
+	long			tx_speed;	/* If MII not used */
+#		define SPEED_UNSET	-1
 
 	/* various kinds of pending driver work */
 	struct sk_buff_head	rxq;
@@ -81,8 +84,6 @@ struct usbnet {
 #		define EVENT_LINK_CHANGE	11
 #		define EVENT_SET_RX_MODE	12
 #		define EVENT_NO_IP_ALIGN	13
-	u32			rx_speed;	/* in bps - NOT Mbps */
-	u32			tx_speed;	/* in bps - NOT Mbps */
 };
 
 static inline struct usb_driver *driver_of(struct usb_interface *intf)
@@ -267,10 +268,12 @@ extern void usbnet_pause_rx(struct usbnet *);
 extern void usbnet_resume_rx(struct usbnet *);
 extern void usbnet_purge_paused_rxq(struct usbnet *);
 
-extern int usbnet_get_link_ksettings(struct net_device *net,
+extern int usbnet_get_link_ksettings_mii(struct net_device *net,
 				     struct ethtool_link_ksettings *cmd);
-extern int usbnet_set_link_ksettings(struct net_device *net,
+extern int usbnet_set_link_ksettings_mii(struct net_device *net,
 				     const struct ethtool_link_ksettings *cmd);
+extern int usbnet_get_link_ksettings_internal(struct net_device *net,
+				     struct ethtool_link_ksettings *cmd);
 extern u32 usbnet_get_link(struct net_device *net);
 extern u32 usbnet_get_msglevel(struct net_device *);
 extern void usbnet_set_msglevel(struct net_device *, u32);