Commit b73be499 authored by Sowjanya Komatineni's avatar Sowjanya Komatineni Committed by Mauro Carvalho Chehab

media: dt-bindings: tegra: Update VI and CSI bindings with port info

Update VI and CSI bindings to add port and endpoint nodes as per
media video-interfaces DT binding document.
Acked-by: default avatarRob Herring <robh@kernel.org>
Signed-off-by: default avatarSowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: default avatarHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: default avatarMauro Carvalho Chehab <mchehab+huawei@kernel.org>
parent 8c393b34
......@@ -51,7 +51,15 @@ of the following host1x client modules:
- vi
- Tegra210:
- power-domains: Must include venc powergate node as vi is in VE partition.
- Tegra210 has CSI part of VI sharing same host interface and register space.
ports (optional node)
vi can have optional ports node and max 6 ports are supported. Each port
should have single 'endpoint' child node. All port nodes are grouped under
ports node. Please refer to the bindings defined in
Documentation/devicetree/bindings/media/video-interfaces.txt
csi (required node)
Tegra210 has CSI part of VI sharing same host interface and register space.
So, VI device node should have CSI child node.
- csi: mipi csi interface to vi
......@@ -65,6 +73,46 @@ of the following host1x client modules:
- power-domains: Must include sor powergate node as csicil is in
SOR partition.
channel (optional nodes)
Maximum 6 channels are supported with each csi brick as either x4 or x2
based on hw connectivity to sensor.
Required properties:
- reg: csi port number. Valid port numbers are 0 through 5.
- nvidia,mipi-calibrate: Should contain a phandle and a specifier
specifying which pads are used by this CSI port and need to be
calibrated. See also ../display/tegra/nvidia,tegra114-mipi.txt.
Each channel node must contain 2 port nodes which can be grouped
under 'ports' node and each port should have a single child 'endpoint'
node.
ports node
Please refer to the bindings defined in
Documentation/devicetree/bindings/media/video-interfaces.txt
ports node must contain below 2 port nodes.
port@0 with single child 'endpoint' node always a sink.
port@1 with single child 'endpoint' node always a source.
port@0 (required node)
Required properties:
- reg: 0
endpoint (required node)
Required properties:
- data-lanes: an array of data lane from 1 to 4. Valid array
lengths are 1/2/4.
- remote-endpoint: phandle to sensor 'endpoint' node.
port@1 (required node)
Required properties:
- reg: 1
endpoint (required node)
Required properties:
- remote-endpoint: phandle to vi port 'endpoint' node.
- epp: encoder pre-processor
Required properties:
......@@ -340,6 +388,18 @@ Example:
ranges = <0x0 0x0 0x54080000 0x2000>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
imx219_vi_in0: endpoint {
remote-endpoint = <&imx219_csi_out0>;
};
};
};
csi@838 {
compatible = "nvidia,tegra210-csi";
reg = <0x838 0x1300>;
......@@ -362,6 +422,34 @@ Example:
<&tegra_car TEGRA210_CLK_CSI_TPG>;
clock-names = "csi", "cilab", "cilcd", "cile", "csi_tpg";
power-domains = <&pd_sor>;
#address-cells = <1>;
#size-cells = <0>;
channel@0 {
reg = <0>;
nvidia,mipi-calibrate = <&mipi 0x001>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
imx219_csi_in0: endpoint {
data-lanes = <1 2>;
remote-endpoint = <&imx219_out0>;
};
};
port@1 {
reg = <1>;
imx219_csi_out0: endpoint {
remote-endpoint = <&imx219_vi_in0>;
};
};
};
};
};
};
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment