ARM: at91: add Atmel's SAMA5D3 Xplained board

Add DT file for new SAMA5D3 Xplained board.
This board is based on Atmel's SAMA5D36 Cortex-A5 SoC.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

arch/arm/boot/dts/Makefile

@@ -38,6 +38,7 @@ dtb-$(CONFIG_ARCH_AT91) += at91sam9g35ek.dtb
 dtb-$(CONFIG_ARCH_AT91) += at91sam9x25ek.dtb
 dtb-$(CONFIG_ARCH_AT91) += at91sam9x35ek.dtb
 # sama5d3
+dtb-$(CONFIG_ARCH_AT91)	+= at91-sama5d3_xplained.dtb
 dtb-$(CONFIG_ARCH_AT91)	+= sama5d31ek.dtb
 dtb-$(CONFIG_ARCH_AT91)	+= sama5d33ek.dtb
 dtb-$(CONFIG_ARCH_AT91)	+= sama5d34ek.dtb

arch/arm/boot/dts/at91-sama5d3_xplained.dts

+/*
+ * at91-sama5d3_xplained.dts - Device Tree file for the SAMA5D3 Xplained board
+ *
+ *  Copyright (C) 2014 Atmel,
+ *		  2014 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "sama5d36.dtsi"
+
+/ {
+	model = "SAMA5D3 Xplained";
+	compatible = "atmel,sama5d3-xplained", "atmel,sama5d3", "atmel,sama5";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x20000000 0x10000000>;
+	};
+
+	ahb {
+		apb {
+			mmc0: mmc@f0000000 {
+				pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_dat4_7 &pinctrl_mmc0_cd>;
+				status = "okay";
+				slot@0 {
+					reg = <0>;
+					bus-width = <8>;
+					cd-gpios = <&pioE 0 GPIO_ACTIVE_LOW>;
+				};
+			};
+
+			spi0: spi@f0004000 {
+				cs-gpios = <&pioD 13 0>;
+				status = "okay";
+			};
+
+			can0: can@f000c000 {
+				status = "okay";
+			};
+
+			i2c0: i2c@f0014000 {
+				status = "okay";
+			};
+
+			i2c1: i2c@f0018000 {
+				status = "okay";
+			};
+
+			macb0: ethernet@f0028000 {
+				phy-mode = "rgmii";
+				status = "okay";
+			};
+
+			usart0: serial@f001c000 {
+				status = "okay";
+			};
+
+			usart1: serial@f0020000 {
+				pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
+				status = "okay";
+			};
+
+			uart0: serial@f0024000 {
+				status = "okay";
+			};
+
+			mmc1: mmc@f8000000 {
+				pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
+				status = "okay";
+				slot@0 {
+					reg = <0>;
+					bus-width = <4>;
+					cd-gpios = <&pioE 1 GPIO_ACTIVE_HIGH>;
+				};
+			};
+
+			spi1: spi@f8008000 {
+				cs-gpios = <&pioC 25 0>, <0>, <0>, <&pioD 16 0>;
+				status = "okay";
+			};
+
+			adc0: adc@f8018000 {
+				pinctrl-0 = <
+					&pinctrl_adc0_adtrg
+					&pinctrl_adc0_ad0
+					&pinctrl_adc0_ad1
+					&pinctrl_adc0_ad2
+					&pinctrl_adc0_ad3
+					&pinctrl_adc0_ad4
+					&pinctrl_adc0_ad5
+					&pinctrl_adc0_ad6
+					&pinctrl_adc0_ad7
+					&pinctrl_adc0_ad8
+					&pinctrl_adc0_ad9
+					>;
+				status = "okay";
+			};
+
+			i2c2: i2c@f801c000 {
+				dmas = <0>, <0>;	/* Do not use DMA for i2c2 */
+				status = "okay";
+			};
+
+			macb1: ethernet@f802c000 {
+				phy-mode = "rmii";
+				status = "okay";
+			};
+
+			dbgu: serial@ffffee00 {
+				status = "okay";
+			};
+
+			pinctrl@fffff200 {
+				board {
+					pinctrl_mmc0_cd: mmc0_cd {
+						atmel,pins =
+							<AT91_PIOE 0 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+					};
+
+					pinctrl_mmc1_cd: mmc1_cd {
+						atmel,pins =
+							<AT91_PIOE 1 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+					};
+
+					pinctrl_usba_vbus: usba_vbus {
+						atmel,pins =
+							<AT91_PIOE 9 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;	/* PE9, conflicts with A9 */
+					};
+				};
+			};
+
+			pmc: pmc@fffffc00 {
+				main: mainck {
+					clock-frequency = <12000000>;
+				};
+			};
+		};
+
+		nand0: nand@60000000 {
+			nand-bus-width = <8>;
+			nand-ecc-mode = "hw";
+			atmel,has-pmecc;
+			atmel,pmecc-cap = <4>;
+			atmel,pmecc-sector-size = <512>;
+			nand-on-flash-bbt;
+			status = "okay";
+
+			at91bootstrap@0 {
+				label = "at91bootstrap";
+				reg = <0x0 0x40000>;
+			};
+
+			bootloader@40000 {
+				label = "bootloader";
+				reg = <0x40000 0x80000>;
+			};
+
+			bootloaderenv@c0000 {
+				label = "bootloader env";
+				reg = <0xc0000 0xc0000>;
+			};
+
+			dtb@180000 {
+				label = "device tree";
+				reg = <0x180000 0x80000>;
+			};
+
+			kernel@200000 {
+				label = "kernel";
+				reg = <0x200000 0x600000>;
+			};
+
+			rootfs@800000 {
+				label = "rootfs";
+				reg = <0x800000 0x0f800000>;
+			};
+		};
+
+		usb0: gadget@00500000 {
+			atmel,vbus-gpio = <&pioE 9 GPIO_ACTIVE_HIGH>;	/* PE9, conflicts with A9 */
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usba_vbus>;
+			status = "okay";
+		};
+
+		usb1: ohci@00600000 {
+			num-ports = <3>;
+			atmel,vbus-gpio = <0
+					   &pioE 3 GPIO_ACTIVE_LOW
+					   &pioE 4 GPIO_ACTIVE_LOW
+					  >;
+			status = "okay";
+		};
+
+		usb2: ehci@00700000 {
+			status = "okay";
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		bp3 {
+			label = "PB_USER";
+			gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
+			linux,code = <0x104>;
+			gpio-key,wakeup;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		d2 {
+			label = "d2";
+			gpios = <&pioE 23 GPIO_ACTIVE_LOW>;	/* PE23, conflicts with A23, CTS2 */
+			linux,default-trigger = "heartbeat";
+		};
+
+		d3 {
+			label = "d3";
+			gpios = <&pioE 24 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};