ARM: OMAP: Make FS USB omap1 only

As the FS USB code is not being actively used for omap2+
there's no point keeping it around for omap2+.

Let's make the FS USB platform init code omap1 only so
we can remove the last user of omap_read/write for omap2+,
and simplify things for further USB, DMA, and device tree
related work.

While at it, also group the mach includes for the related
drivers.

Cc: linux-usb@vger.kernel.org
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

arch/arm/mach-omap1/board-ams-delta.c

@@ -37,12 +37,12 @@
 #include <plat/board-ams-delta.h>
 #include <plat/keypad.h>
 #include <plat/mux.h>
-#include <plat/usb.h>
 #include <plat/board.h>
 
 #include <mach/hardware.h>
 #include <mach/ams-delta-fiq.h>
 #include <mach/camera.h>
+#include <mach/usb.h>
 
 #include "iomap.h"
 #include "common.h"

arch/arm/mach-omap1/board-generic.c

@@ -23,8 +23,10 @@
 #include <asm/mach/map.h>
 
 #include <plat/mux.h>
-#include <plat/usb.h>
 #include <plat/board.h>
+
+#include <mach/usb.h>
+
 #include "common.h"
 
 /* assume no Mini-AB port */

arch/arm/mach-omap1/board-h2.c

@@ -40,11 +40,11 @@
 #include <plat/dma.h>
 #include <plat/tc.h>
 #include <plat/irda.h>
-#include <plat/usb.h>
 #include <plat/keypad.h>
 #include <plat/flash.h>
 
 #include <mach/hardware.h>
+#include <mach/usb.h>
 
 #include "common.h"
 #include "board-h2.h"

arch/arm/mach-omap1/board-h3.c

@@ -40,13 +40,13 @@
 
 #include <plat/mux.h>
 #include <plat/tc.h>
-#include <plat/usb.h>
 #include <plat/keypad.h>
 #include <plat/dma.h>
 #include <plat/flash.h>
 
 #include <mach/hardware.h>
 #include <mach/irqs.h>
+#include <mach/usb.h>
 
 #include "common.h"
 #include "board-h3.h"

arch/arm/mach-omap1/board-htcherald.c

@@ -44,10 +44,10 @@
 #include <plat/omap7xx.h>
 #include <plat/board.h>
 #include <plat/keypad.h>
-#include <plat/usb.h>
 #include <plat/mmc.h>
 
 #include <mach/irqs.h>
+#include <mach/usb.h>
 
 #include "common.h"
 

arch/arm/mach-omap1/board-innovator.c

@@ -35,11 +35,11 @@
 #include <plat/flash.h>
 #include <plat/fpga.h>
 #include <plat/tc.h>
-#include <plat/usb.h>
 #include <plat/keypad.h>
 #include <plat/mmc.h>
 
 #include <mach/hardware.h>
+#include <mach/usb.h>
 
 #include "iomap.h"
 #include "common.h"

arch/arm/mach-omap1/board-nokia770.c

@@ -26,7 +26,6 @@
 #include <asm/mach/map.h>
 
 #include <plat/mux.h>
-#include <plat/usb.h>
 #include <plat/board.h>
 #include <plat/keypad.h>
 #include <plat/lcd_mipid.h>
@@ -34,6 +33,7 @@
 #include <plat/clock.h>
 
 #include <mach/hardware.h>
+#include <mach/usb.h>
 
 #include "common.h"
 

arch/arm/mach-omap1/board-osk.c

@@ -45,11 +45,11 @@
 #include <asm/mach/map.h>
 
 #include <plat/flash.h>
-#include <plat/usb.h>
 #include <plat/mux.h>
 #include <plat/tc.h>
 
 #include <mach/hardware.h>
+#include <mach/usb.h>
 
 #include "common.h"
 

arch/arm/mach-omap1/board-palmte.c

@@ -35,7 +35,6 @@
 
 #include <plat/flash.h>
 #include <plat/mux.h>
-#include <plat/usb.h>
 #include <plat/tc.h>
 #include <plat/dma.h>
 #include <plat/board.h>
@@ -43,6 +42,7 @@
 #include <plat/keypad.h>
 
 #include <mach/hardware.h>
+#include <mach/usb.h>
 
 #include "common.h"
 

arch/arm/mach-omap1/board-palmtt.c

@@ -35,7 +35,6 @@
 #include <plat/led.h>
 #include <plat/flash.h>
 #include <plat/mux.h>
-#include <plat/usb.h>
 #include <plat/dma.h>
 #include <plat/tc.h>
 #include <plat/board.h>
@@ -43,6 +42,7 @@
 #include <plat/keypad.h>
 
 #include <mach/hardware.h>
+#include <mach/usb.h>
 
 #include "common.h"
 

arch/arm/mach-omap1/board-palmz71.c

@@ -37,7 +37,6 @@
 
 #include <plat/flash.h>
 #include <plat/mux.h>
-#include <plat/usb.h>
 #include <plat/dma.h>
 #include <plat/tc.h>
 #include <plat/board.h>
@@ -45,6 +44,7 @@
 #include <plat/keypad.h>
 
 #include <mach/hardware.h>
+#include <mach/usb.h>
 
 #include "common.h"
 

arch/arm/mach-omap1/board-sx1.c

@@ -37,13 +37,13 @@
 #include <plat/mux.h>
 #include <plat/dma.h>
 #include <plat/irda.h>
-#include <plat/usb.h>
 #include <plat/tc.h>
 #include <plat/board.h>
 #include <plat/keypad.h>
 #include <plat/board-sx1.h>
 
 #include <mach/hardware.h>
+#include <mach/usb.h>
 
 #include "common.h"
 

arch/arm/mach-omap1/board-voiceblue.c

@@ -35,9 +35,10 @@
 #include <plat/flash.h>
 #include <plat/mux.h>
 #include <plat/tc.h>
-#include <plat/usb.h>
+#include <plat/board.h>
 
 #include <mach/hardware.h>
+#include <mach/usb.h>
 
 #include "common.h"
 

arch/arm/mach-omap1/clock_data.c

@@ -25,10 +25,11 @@
 #include <plat/clock.h>
 #include <plat/cpu.h>
 #include <plat/clkdev_omap.h>
+#include <plat/board.h>
 #include <plat/sram.h>	/* for omap_sram_reprogram_clock() */
-#include <plat/usb.h>   /* for OTG_BASE */
 
 #include <mach/hardware.h>
+#include <mach/usb.h>   /* for OTG_BASE */
 
 #include "iomap.h"
 #include "clock.h"

arch/arm/mach-omap1/include/mach/usb.h

+/*
+ * FIXME correct answer depends on hmc_mode,
+ * as does (on omap1) any nonzero value for config->otg port number
+ */
+#ifdef	CONFIG_USB_GADGET_OMAP
+#define	is_usb0_device(config)	1
+#else
+#define	is_usb0_device(config)	0
+#endif
+
+struct omap_usb_config {
+	/* Configure drivers according to the connectors on your board:
+	 *  - "A" connector (rectagular)
+	 *	... for host/OHCI use, set "register_host".
+	 *  - "B" connector (squarish) or "Mini-B"
+	 *	... for device/gadget use, set "register_dev".
+	 *  - "Mini-AB" connector (very similar to Mini-B)
+	 *	... for OTG use as device OR host, initialize "otg"
+	 */
+	unsigned	register_host:1;
+	unsigned	register_dev:1;
+	u8		otg;	/* port number, 1-based:  usb1 == 2 */
+
+	u8		hmc_mode;
+
+	/* implicitly true if otg:  host supports remote wakeup? */
+	u8		rwc;
+
+	/* signaling pins used to talk to transceiver on usbN:
+	 *  0 == usbN unused
+	 *  2 == usb0-only, using internal transceiver
+	 *  3 == 3 wire bidirectional
+	 *  4 == 4 wire bidirectional
+	 *  6 == 6 wire unidirectional (or TLL)
+	 */
+	u8		pins[3];
+
+	struct platform_device *udc_device;
+	struct platform_device *ohci_device;
+	struct platform_device *otg_device;
+
+	u32 (*usb0_init)(unsigned nwires, unsigned is_device);
+	u32 (*usb1_init)(unsigned nwires);
+	u32 (*usb2_init)(unsigned nwires, unsigned alt_pingroup);
+
+	int (*ocpi_enable)(void);
+};
+
+void omap_otg_init(struct omap_usb_config *config);
+
+#if defined(CONFIG_USB) || defined(CONFIG_USB_MODULE)
+void omap1_usb_init(struct omap_usb_config *pdata);
+#else
+static inline void omap1_usb_init(struct omap_usb_config *pdata)
+{
+}
+#endif
+
+#define OMAP1_OTG_BASE			0xfffb0400
+#define OMAP1_UDC_BASE			0xfffb4000
+#define OMAP1_OHCI_BASE			0xfffba000
+
+#define OMAP2_OHCI_BASE			0x4805e000
+#define OMAP2_UDC_BASE			0x4805e200
+#define OMAP2_OTG_BASE			0x4805e300
+#define OTG_BASE			OMAP1_OTG_BASE
+#define UDC_BASE			OMAP1_UDC_BASE
+#define OMAP_OHCI_BASE			OMAP1_OHCI_BASE
+
+/*
+ * OTG and transceiver registers, for OMAPs starting with ARM926
+ */
+#define OTG_REV				(OTG_BASE + 0x00)
+#define OTG_SYSCON_1			(OTG_BASE + 0x04)
+#	define	 USB2_TRX_MODE(w)	(((w)>>24)&0x07)
+#	define	 USB1_TRX_MODE(w)	(((w)>>20)&0x07)
+#	define	 USB0_TRX_MODE(w)	(((w)>>16)&0x07)
+#	define	 OTG_IDLE_EN		(1 << 15)
+#	define	 HST_IDLE_EN		(1 << 14)
+#	define	 DEV_IDLE_EN		(1 << 13)
+#	define	 OTG_RESET_DONE		(1 << 2)
+#	define	 OTG_SOFT_RESET		(1 << 1)
+#define OTG_SYSCON_2			(OTG_BASE + 0x08)
+#	define	 OTG_EN			(1 << 31)
+#	define	 USBX_SYNCHRO		(1 << 30)
+#	define	 OTG_MST16		(1 << 29)
+#	define	 SRP_GPDATA		(1 << 28)
+#	define	 SRP_GPDVBUS		(1 << 27)
+#	define	 SRP_GPUVBUS(w)		(((w)>>24)&0x07)
+#	define	 A_WAIT_VRISE(w)	(((w)>>20)&0x07)
+#	define	 B_ASE_BRST(w)		(((w)>>16)&0x07)
+#	define	 SRP_DPW		(1 << 14)
+#	define	 SRP_DATA		(1 << 13)
+#	define	 SRP_VBUS		(1 << 12)
+#	define	 OTG_PADEN		(1 << 10)
+#	define	 HMC_PADEN		(1 << 9)
+#	define	 UHOST_EN		(1 << 8)
+#	define	 HMC_TLLSPEED		(1 << 7)
+#	define	 HMC_TLLATTACH		(1 << 6)
+#	define	 OTG_HMC(w)		(((w)>>0)&0x3f)
+#define OTG_CTRL			(OTG_BASE + 0x0c)
+#	define	 OTG_USB2_EN		(1 << 29)
+#	define	 OTG_USB2_DP		(1 << 28)
+#	define	 OTG_USB2_DM		(1 << 27)
+#	define	 OTG_USB1_EN		(1 << 26)
+#	define	 OTG_USB1_DP		(1 << 25)
+#	define	 OTG_USB1_DM		(1 << 24)
+#	define	 OTG_USB0_EN		(1 << 23)
+#	define	 OTG_USB0_DP		(1 << 22)
+#	define	 OTG_USB0_DM		(1 << 21)
+#	define	 OTG_ASESSVLD		(1 << 20)
+#	define	 OTG_BSESSEND		(1 << 19)
+#	define	 OTG_BSESSVLD		(1 << 18)
+#	define	 OTG_VBUSVLD		(1 << 17)
+#	define	 OTG_ID			(1 << 16)
+#	define	 OTG_DRIVER_SEL		(1 << 15)
+#	define	 OTG_A_SETB_HNPEN	(1 << 12)
+#	define	 OTG_A_BUSREQ		(1 << 11)
+#	define	 OTG_B_HNPEN		(1 << 9)
+#	define	 OTG_B_BUSREQ		(1 << 8)
+#	define	 OTG_BUSDROP		(1 << 7)
+#	define	 OTG_PULLDOWN		(1 << 5)
+#	define	 OTG_PULLUP		(1 << 4)
+#	define	 OTG_DRV_VBUS		(1 << 3)
+#	define	 OTG_PD_VBUS		(1 << 2)
+#	define	 OTG_PU_VBUS		(1 << 1)
+#	define	 OTG_PU_ID		(1 << 0)
+#define OTG_IRQ_EN			(OTG_BASE + 0x10)	/* 16-bit */
+#	define	 DRIVER_SWITCH		(1 << 15)
+#	define	 A_VBUS_ERR		(1 << 13)
+#	define	 A_REQ_TMROUT		(1 << 12)
+#	define	 A_SRP_DETECT		(1 << 11)
+#	define	 B_HNP_FAIL		(1 << 10)
+#	define	 B_SRP_TMROUT		(1 << 9)
+#	define	 B_SRP_DONE		(1 << 8)
+#	define	 B_SRP_STARTED		(1 << 7)
+#	define	 OPRT_CHG		(1 << 0)
+#define OTG_IRQ_SRC			(OTG_BASE + 0x14)	/* 16-bit */
+	// same bits as in IRQ_EN
+#define OTG_OUTCTRL			(OTG_BASE + 0x18)	/* 16-bit */
+#	define	 OTGVPD			(1 << 14)
+#	define	 OTGVPU			(1 << 13)
+#	define	 OTGPUID		(1 << 12)
+#	define	 USB2VDR		(1 << 10)
+#	define	 USB2PDEN		(1 << 9)
+#	define	 USB2PUEN		(1 << 8)
+#	define	 USB1VDR		(1 << 6)
+#	define	 USB1PDEN		(1 << 5)
+#	define	 USB1PUEN		(1 << 4)
+#	define	 USB0VDR		(1 << 2)
+#	define	 USB0PDEN		(1 << 1)
+#	define	 USB0PUEN		(1 << 0)
+#define OTG_TEST			(OTG_BASE + 0x20)	/* 16-bit */
+#define OTG_VENDOR_CODE			(OTG_BASE + 0xfc)	/* 16-bit */
+
+/*-------------------------------------------------------------------------*/
+
+/* OMAP1 */
+#define	USB_TRANSCEIVER_CTRL		(0xfffe1000 + 0x0064)
+#	define	CONF_USB2_UNI_R		(1 << 8)
+#	define	CONF_USB1_UNI_R		(1 << 7)
+#	define	CONF_USB_PORT0_R(x)	(((x)>>4)&0x7)
+#	define	CONF_USB0_ISOLATE_R	(1 << 3)
+#	define	CONF_USB_PWRDN_DM_R	(1 << 2)
+#	define	CONF_USB_PWRDN_DP_R	(1 << 1)

arch/arm/mach-omap1/usb.c

@@ -27,7 +27,8 @@
 #include <asm/irq.h>
 
 #include <plat/mux.h>
-#include <plat/usb.h>
+
+#include <mach/usb.h>
 
 #include "common.h"
 
@@ -55,6 +56,119 @@
 #define INT_USB_IRQ_HGEN	INT_USB_HHC_1
 #define INT_USB_IRQ_OTG		IH2_BASE + 8
 
+#ifdef	CONFIG_ARCH_OMAP_OTG
+
+void __init
+omap_otg_init(struct omap_usb_config *config)
+{
+	u32		syscon;
+	int		alt_pingroup = 0;
+
+	/* NOTE:  no bus or clock setup (yet?) */
+
+	syscon = omap_readl(OTG_SYSCON_1) & 0xffff;
+	if (!(syscon & OTG_RESET_DONE))
+		pr_debug("USB resets not complete?\n");
+
+	//omap_writew(0, OTG_IRQ_EN);
+
+	/* pin muxing and transceiver pinouts */
+	if (config->pins[0] > 2)	/* alt pingroup 2 */
+		alt_pingroup = 1;
+	syscon |= config->usb0_init(config->pins[0], is_usb0_device(config));
+	syscon |= config->usb1_init(config->pins[1]);
+	syscon |= config->usb2_init(config->pins[2], alt_pingroup);
+	pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
+	omap_writel(syscon, OTG_SYSCON_1);
+
+	syscon = config->hmc_mode;
+	syscon |= USBX_SYNCHRO | (4 << 16) /* B_ASE0_BRST */;
+#ifdef	CONFIG_USB_OTG
+	if (config->otg)
+		syscon |= OTG_EN;
+#endif
+	if (cpu_class_is_omap1())
+		pr_debug("USB_TRANSCEIVER_CTRL = %03x\n",
+			 omap_readl(USB_TRANSCEIVER_CTRL));
+	pr_debug("OTG_SYSCON_2 = %08x\n", omap_readl(OTG_SYSCON_2));
+	omap_writel(syscon, OTG_SYSCON_2);
+
+	printk("USB: hmc %d", config->hmc_mode);
+	if (!alt_pingroup)
+		printk(", usb2 alt %d wires", config->pins[2]);
+	else if (config->pins[0])
+		printk(", usb0 %d wires%s", config->pins[0],
+			is_usb0_device(config) ? " (dev)" : "");
+	if (config->pins[1])
+		printk(", usb1 %d wires", config->pins[1]);
+	if (!alt_pingroup && config->pins[2])
+		printk(", usb2 %d wires", config->pins[2]);
+	if (config->otg)
+		printk(", Mini-AB on usb%d", config->otg - 1);
+	printk("\n");
+
+	if (cpu_class_is_omap1()) {
+		u16 w;
+
+		/* leave USB clocks/controllers off until needed */
+		w = omap_readw(ULPD_SOFT_REQ);
+		w &= ~SOFT_USB_CLK_REQ;
+		omap_writew(w, ULPD_SOFT_REQ);
+
+		w = omap_readw(ULPD_CLOCK_CTRL);
+		w &= ~USB_MCLK_EN;
+		w |= DIS_USB_PVCI_CLK;
+		omap_writew(w, ULPD_CLOCK_CTRL);
+	}
+	syscon = omap_readl(OTG_SYSCON_1);
+	syscon |= HST_IDLE_EN|DEV_IDLE_EN|OTG_IDLE_EN;
+
+#ifdef	CONFIG_USB_GADGET_OMAP
+	if (config->otg || config->register_dev) {
+		struct platform_device *udc_device = config->udc_device;
+		int status;
+
+		syscon &= ~DEV_IDLE_EN;
+		udc_device->dev.platform_data = config;
+		status = platform_device_register(udc_device);
+		if (status)
+			pr_debug("can't register UDC device, %d\n", status);
+	}
+#endif
+
+#if	defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+	if (config->otg || config->register_host) {
+		struct platform_device *ohci_device = config->ohci_device;
+		int status;
+
+		syscon &= ~HST_IDLE_EN;
+		ohci_device->dev.platform_data = config;
+		status = platform_device_register(ohci_device);
+		if (status)
+			pr_debug("can't register OHCI device, %d\n", status);
+	}
+#endif
+
+#ifdef	CONFIG_USB_OTG
+	if (config->otg) {
+		struct platform_device *otg_device = config->otg_device;
+		int status;
+
+		syscon &= ~OTG_IDLE_EN;
+		otg_device->dev.platform_data = config;
+		status = platform_device_register(otg_device);
+		if (status)
+			pr_debug("can't register OTG device, %d\n", status);
+	}
+#endif
+	pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
+	omap_writel(syscon, OTG_SYSCON_1);
+}
+
+#else
+void omap_otg_init(struct omap_usb_config *config) {}
+#endif
+
 #ifdef	CONFIG_USB_GADGET_OMAP
 
 static struct resource udc_resources[] = {

arch/arm/plat-omap/Makefile

@@ -4,7 +4,7 @@
 
 # Common support
 obj-y := common.o sram.o clock.o devices.o dma.o mux.o \
-	 usb.o fb.o counter_32k.o
+	 fb.o counter_32k.o
 obj-m :=
 obj-n :=
 obj-  :=

arch/arm/plat-omap/include/plat/board.h

@@ -57,44 +57,6 @@ struct omap_camera_sensor_config {
 	int (*power_off)(void * data);
 };
 
-struct omap_usb_config {
-	/* Configure drivers according to the connectors on your board:
-	 *  - "A" connector (rectagular)
-	 *	... for host/OHCI use, set "register_host".
-	 *  - "B" connector (squarish) or "Mini-B"
-	 *	... for device/gadget use, set "register_dev".
-	 *  - "Mini-AB" connector (very similar to Mini-B)
-	 *	... for OTG use as device OR host, initialize "otg"
-	 */
-	unsigned	register_host:1;
-	unsigned	register_dev:1;
-	u8		otg;	/* port number, 1-based:  usb1 == 2 */
-
-	u8		hmc_mode;
-
-	/* implicitly true if otg:  host supports remote wakeup? */
-	u8		rwc;
-
-	/* signaling pins used to talk to transceiver on usbN:
-	 *  0 == usbN unused
-	 *  2 == usb0-only, using internal transceiver
-	 *  3 == 3 wire bidirectional
-	 *  4 == 4 wire bidirectional
-	 *  6 == 6 wire unidirectional (or TLL)
-	 */
-	u8		pins[3];
-
-	struct platform_device *udc_device;
-	struct platform_device *ohci_device;
-	struct platform_device *otg_device;
-
-	u32 (*usb0_init)(unsigned nwires, unsigned is_device);
-	u32 (*usb1_init)(unsigned nwires);
-	u32 (*usb2_init)(unsigned nwires, unsigned alt_pingroup);
-
-	int (*ocpi_enable)(void);
-};
-
 struct omap_lcd_config {
 	char panel_name[16];
 	char ctrl_name[16];

arch/arm/plat-omap/include/plat/usb.h

@@ -44,6 +44,8 @@ struct usbhs_omap_board_data {
 	struct regulator		*regulator[OMAP3_HS_USB_PORTS];
 };
 
+#ifdef CONFIG_ARCH_OMAP2PLUS
+
 struct ehci_hcd_omap_platform_data {
 	enum usbhs_omap_port_mode	port_mode[OMAP3_HS_USB_PORTS];
 	int				reset_gpio_port[OMAP3_HS_USB_PORTS];
@@ -64,26 +66,6 @@ struct usbhs_omap_platform_data {
 };
 /*-------------------------------------------------------------------------*/
 
-#define OMAP1_OTG_BASE			0xfffb0400
-#define OMAP1_UDC_BASE			0xfffb4000
-#define OMAP1_OHCI_BASE			0xfffba000
-
-#define OMAP2_OHCI_BASE			0x4805e000
-#define OMAP2_UDC_BASE			0x4805e200
-#define OMAP2_OTG_BASE			0x4805e300
-
-#ifdef CONFIG_ARCH_OMAP1
-
-#define OTG_BASE			OMAP1_OTG_BASE
-#define UDC_BASE			OMAP1_UDC_BASE
-#define OMAP_OHCI_BASE			OMAP1_OHCI_BASE
-
-#else
-
-#define OTG_BASE			OMAP2_OTG_BASE
-#define UDC_BASE			OMAP2_UDC_BASE
-#define OMAP_OHCI_BASE			OMAP2_OHCI_BASE
-
 struct omap_musb_board_data {
 	u8	interface_type;
 	u8	mode;
@@ -107,44 +89,6 @@ extern int omap4430_phy_init(struct device *dev);
 extern int omap4430_phy_exit(struct device *dev);
 extern int omap4430_phy_suspend(struct device *dev, int suspend);
 
-/*
- * NOTE: Please update omap USB drivers to use ioremap + read/write
- */
-
-#define OMAP2_L4_IO_OFFSET	0xb2000000
-#define OMAP2_L4_IO_ADDRESS(pa)	IOMEM((pa) + OMAP2_L4_IO_OFFSET)
-
-static inline u8 omap_readb(u32 pa)
-{
-	return __raw_readb(OMAP2_L4_IO_ADDRESS(pa));
-}
-
-static inline u16 omap_readw(u32 pa)
-{
-	return __raw_readw(OMAP2_L4_IO_ADDRESS(pa));
-}
-
-static inline u32 omap_readl(u32 pa)
-{
-	return __raw_readl(OMAP2_L4_IO_ADDRESS(pa));
-}
-
-static inline void omap_writeb(u8 v, u32 pa)
-{
-	__raw_writeb(v, OMAP2_L4_IO_ADDRESS(pa));
-}
-
-
-static inline void omap_writew(u16 v, u32 pa)
-{
-	__raw_writew(v, OMAP2_L4_IO_ADDRESS(pa));
-}
-
-static inline void omap_writel(u32 v, u32 pa)
-{
-	__raw_writel(v, OMAP2_L4_IO_ADDRESS(pa));
-}
-
 #endif
 
 extern void am35x_musb_reset(void);
@@ -153,142 +97,6 @@ extern void am35x_musb_clear_irq(void);
 extern void am35x_set_mode(u8 musb_mode);
 extern void ti81xx_musb_phy_power(u8 on);
 
-/*
- * FIXME correct answer depends on hmc_mode,
- * as does (on omap1) any nonzero value for config->otg port number
- */
-#ifdef	CONFIG_USB_GADGET_OMAP
-#define	is_usb0_device(config)	1
-#else
-#define	is_usb0_device(config)	0
-#endif
-
-void omap_otg_init(struct omap_usb_config *config);
-
-#if defined(CONFIG_USB) || defined(CONFIG_USB_MODULE)
-void omap1_usb_init(struct omap_usb_config *pdata);
-#else
-static inline void omap1_usb_init(struct omap_usb_config *pdata)
-{
-}
-#endif
-
-#if defined(CONFIG_ARCH_OMAP_OTG) || defined(CONFIG_ARCH_OMAP_OTG_MODULE)
-void omap2_usbfs_init(struct omap_usb_config *pdata);
-#else
-static inline void omap2_usbfs_init(struct omap_usb_config *pdata)
-{
-}
-#endif
-
-/*-------------------------------------------------------------------------*/
-
-/*
- * OTG and transceiver registers, for OMAPs starting with ARM926
- */
-#define OTG_REV				(OTG_BASE + 0x00)
-#define OTG_SYSCON_1			(OTG_BASE + 0x04)
-#	define	 USB2_TRX_MODE(w)	(((w)>>24)&0x07)
-#	define	 USB1_TRX_MODE(w)	(((w)>>20)&0x07)
-#	define	 USB0_TRX_MODE(w)	(((w)>>16)&0x07)
-#	define	 OTG_IDLE_EN		(1 << 15)
-#	define	 HST_IDLE_EN		(1 << 14)
-#	define	 DEV_IDLE_EN		(1 << 13)
-#	define	 OTG_RESET_DONE		(1 << 2)
-#	define	 OTG_SOFT_RESET		(1 << 1)
-#define OTG_SYSCON_2			(OTG_BASE + 0x08)
-#	define	 OTG_EN			(1 << 31)
-#	define	 USBX_SYNCHRO		(1 << 30)
-#	define	 OTG_MST16		(1 << 29)
-#	define	 SRP_GPDATA		(1 << 28)
-#	define	 SRP_GPDVBUS		(1 << 27)
-#	define	 SRP_GPUVBUS(w)		(((w)>>24)&0x07)
-#	define	 A_WAIT_VRISE(w)	(((w)>>20)&0x07)
-#	define	 B_ASE_BRST(w)		(((w)>>16)&0x07)
-#	define	 SRP_DPW		(1 << 14)
-#	define	 SRP_DATA		(1 << 13)
-#	define	 SRP_VBUS		(1 << 12)
-#	define	 OTG_PADEN		(1 << 10)
-#	define	 HMC_PADEN		(1 << 9)
-#	define	 UHOST_EN		(1 << 8)
-#	define	 HMC_TLLSPEED		(1 << 7)
-#	define	 HMC_TLLATTACH		(1 << 6)
-#	define	 OTG_HMC(w)		(((w)>>0)&0x3f)
-#define OTG_CTRL			(OTG_BASE + 0x0c)
-#	define	 OTG_USB2_EN		(1 << 29)
-#	define	 OTG_USB2_DP		(1 << 28)
-#	define	 OTG_USB2_DM		(1 << 27)
-#	define	 OTG_USB1_EN		(1 << 26)
-#	define	 OTG_USB1_DP		(1 << 25)
-#	define	 OTG_USB1_DM		(1 << 24)
-#	define	 OTG_USB0_EN		(1 << 23)
-#	define	 OTG_USB0_DP		(1 << 22)
-#	define	 OTG_USB0_DM		(1 << 21)
-#	define	 OTG_ASESSVLD		(1 << 20)
-#	define	 OTG_BSESSEND		(1 << 19)
-#	define	 OTG_BSESSVLD		(1 << 18)
-#	define	 OTG_VBUSVLD		(1 << 17)
-#	define	 OTG_ID			(1 << 16)
-#	define	 OTG_DRIVER_SEL		(1 << 15)
-#	define	 OTG_A_SETB_HNPEN	(1 << 12)
-#	define	 OTG_A_BUSREQ		(1 << 11)
-#	define	 OTG_B_HNPEN		(1 << 9)
-#	define	 OTG_B_BUSREQ		(1 << 8)
-#	define	 OTG_BUSDROP		(1 << 7)
-#	define	 OTG_PULLDOWN		(1 << 5)
-#	define	 OTG_PULLUP		(1 << 4)
-#	define	 OTG_DRV_VBUS		(1 << 3)
-#	define	 OTG_PD_VBUS		(1 << 2)
-#	define	 OTG_PU_VBUS		(1 << 1)
-#	define	 OTG_PU_ID		(1 << 0)
-#define OTG_IRQ_EN			(OTG_BASE + 0x10)	/* 16-bit */
-#	define	 DRIVER_SWITCH		(1 << 15)
-#	define	 A_VBUS_ERR		(1 << 13)
-#	define	 A_REQ_TMROUT		(1 << 12)
-#	define	 A_SRP_DETECT		(1 << 11)
-#	define	 B_HNP_FAIL		(1 << 10)
-#	define	 B_SRP_TMROUT		(1 << 9)
-#	define	 B_SRP_DONE		(1 << 8)
-#	define	 B_SRP_STARTED		(1 << 7)
-#	define	 OPRT_CHG		(1 << 0)
-#define OTG_IRQ_SRC			(OTG_BASE + 0x14)	/* 16-bit */
-	// same bits as in IRQ_EN
-#define OTG_OUTCTRL			(OTG_BASE + 0x18)	/* 16-bit */
-#	define	 OTGVPD			(1 << 14)
-#	define	 OTGVPU			(1 << 13)
-#	define	 OTGPUID		(1 << 12)
-#	define	 USB2VDR		(1 << 10)
-#	define	 USB2PDEN		(1 << 9)
-#	define	 USB2PUEN		(1 << 8)
-#	define	 USB1VDR		(1 << 6)
-#	define	 USB1PDEN		(1 << 5)
-#	define	 USB1PUEN		(1 << 4)
-#	define	 USB0VDR		(1 << 2)
-#	define	 USB0PDEN		(1 << 1)
-#	define	 USB0PUEN		(1 << 0)
-#define OTG_TEST			(OTG_BASE + 0x20)	/* 16-bit */
-#define OTG_VENDOR_CODE			(OTG_BASE + 0xfc)	/* 16-bit */
-
-/*-------------------------------------------------------------------------*/
-
-/* OMAP1 */
-#define	USB_TRANSCEIVER_CTRL		(0xfffe1000 + 0x0064)
-#	define	CONF_USB2_UNI_R		(1 << 8)
-#	define	CONF_USB1_UNI_R		(1 << 7)
-#	define	CONF_USB_PORT0_R(x)	(((x)>>4)&0x7)
-#	define	CONF_USB0_ISOLATE_R	(1 << 3)
-#	define	CONF_USB_PWRDN_DM_R	(1 << 2)
-#	define	CONF_USB_PWRDN_DP_R	(1 << 1)
-
-/* OMAP2 */
-#	define	USB_UNIDIR			0x0
-#	define	USB_UNIDIR_TLL			0x1
-#	define	USB_BIDIR			0x2
-#	define	USB_BIDIR_TLL			0x3
-#	define	USBTXWRMODEI(port, x)	((x) << (22 - (port * 2)))
-#	define	USBT2TLL5PI		(1 << 17)
-#	define	USB0PUENACTLOI		(1 << 16)
-#	define	USBSTANDBYCTRL		(1 << 15)
 /* AM35x */
 /* USB 2.0 PHY Control */
 #define CONF2_PHY_GPIOMODE	(1 << 23)

arch/arm/plat-omap/usb.c

- /*
- * arch/arm/plat-omap/usb.c -- platform level USB initialization
- *
- * Copyright (C) 2004 Texas Instruments, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#undef	DEBUG
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-
-#include <plat/usb.h>
-#include <plat/board.h>
-
-#include <mach/hardware.h>
-
-#ifdef	CONFIG_ARCH_OMAP_OTG
-
-void __init
-omap_otg_init(struct omap_usb_config *config)
-{
-	u32		syscon;
-	int		alt_pingroup = 0;
-
-	/* NOTE:  no bus or clock setup (yet?) */
-
-	syscon = omap_readl(OTG_SYSCON_1) & 0xffff;
-	if (!(syscon & OTG_RESET_DONE))
-		pr_debug("USB resets not complete?\n");
-
-	//omap_writew(0, OTG_IRQ_EN);
-
-	/* pin muxing and transceiver pinouts */
-	if (config->pins[0] > 2)	/* alt pingroup 2 */
-		alt_pingroup = 1;
-	syscon |= config->usb0_init(config->pins[0], is_usb0_device(config));
-	syscon |= config->usb1_init(config->pins[1]);
-	syscon |= config->usb2_init(config->pins[2], alt_pingroup);
-	pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
-	omap_writel(syscon, OTG_SYSCON_1);
-
-	syscon = config->hmc_mode;
-	syscon |= USBX_SYNCHRO | (4 << 16) /* B_ASE0_BRST */;
-#ifdef	CONFIG_USB_OTG
-	if (config->otg)
-		syscon |= OTG_EN;
-#endif
-	if (cpu_class_is_omap1())
-		pr_debug("USB_TRANSCEIVER_CTRL = %03x\n",
-			 omap_readl(USB_TRANSCEIVER_CTRL));
-	pr_debug("OTG_SYSCON_2 = %08x\n", omap_readl(OTG_SYSCON_2));
-	omap_writel(syscon, OTG_SYSCON_2);
-
-	printk("USB: hmc %d", config->hmc_mode);
-	if (!alt_pingroup)
-		printk(", usb2 alt %d wires", config->pins[2]);
-	else if (config->pins[0])
-		printk(", usb0 %d wires%s", config->pins[0],
-			is_usb0_device(config) ? " (dev)" : "");
-	if (config->pins[1])
-		printk(", usb1 %d wires", config->pins[1]);
-	if (!alt_pingroup && config->pins[2])
-		printk(", usb2 %d wires", config->pins[2]);
-	if (config->otg)
-		printk(", Mini-AB on usb%d", config->otg - 1);
-	printk("\n");
-
-	if (cpu_class_is_omap1()) {
-		u16 w;
-
-		/* leave USB clocks/controllers off until needed */
-		w = omap_readw(ULPD_SOFT_REQ);
-		w &= ~SOFT_USB_CLK_REQ;
-		omap_writew(w, ULPD_SOFT_REQ);
-
-		w = omap_readw(ULPD_CLOCK_CTRL);
-		w &= ~USB_MCLK_EN;
-		w |= DIS_USB_PVCI_CLK;
-		omap_writew(w, ULPD_CLOCK_CTRL);
-	}
-	syscon = omap_readl(OTG_SYSCON_1);
-	syscon |= HST_IDLE_EN|DEV_IDLE_EN|OTG_IDLE_EN;
-
-#ifdef	CONFIG_USB_GADGET_OMAP
-	if (config->otg || config->register_dev) {
-		struct platform_device *udc_device = config->udc_device;
-		int status;
-
-		syscon &= ~DEV_IDLE_EN;
-		udc_device->dev.platform_data = config;
-		status = platform_device_register(udc_device);
-		if (status)
-			pr_debug("can't register UDC device, %d\n", status);
-	}
-#endif
-
-#if	defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-	if (config->otg || config->register_host) {
-		struct platform_device *ohci_device = config->ohci_device;
-		int status;
-
-		syscon &= ~HST_IDLE_EN;
-		ohci_device->dev.platform_data = config;
-		status = platform_device_register(ohci_device);
-		if (status)
-			pr_debug("can't register OHCI device, %d\n", status);
-	}
-#endif
-
-#ifdef	CONFIG_USB_OTG
-	if (config->otg) {
-		struct platform_device *otg_device = config->otg_device;
-		int status;
-
-		syscon &= ~OTG_IDLE_EN;
-		otg_device->dev.platform_data = config;
-		status = platform_device_register(otg_device);
-		if (status)
-			pr_debug("can't register OTG device, %d\n", status);
-	}
-#endif
-	pr_debug("OTG_SYSCON_1 = %08x\n", omap_readl(OTG_SYSCON_1));
-	omap_writel(syscon, OTG_SYSCON_1);
-}
-
-#else
-void omap_otg_init(struct omap_usb_config *config) {}
-#endif

drivers/usb/gadget/Kconfig

@@ -185,7 +185,7 @@ config USB_FUSB300
 
 config USB_OMAP
 	tristate "OMAP USB Device Controller"
-	depends on ARCH_OMAP
+	depends on ARCH_OMAP1
 	select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3 || MACH_OMAP_H4_OTG
 	select USB_OTG_UTILS if ARCH_OMAP
 	help

drivers/usb/gadget/omap_udc.c

@@ -44,7 +44,8 @@
 #include <asm/mach-types.h>
 
 #include <plat/dma.h>
-#include <plat/usb.h>
+
+#include <mach/usb.h>
 
 #include "omap_udc.h"
 

drivers/usb/host/Kconfig

@@ -308,7 +308,7 @@ config USB_OHCI_HCD
 
 config USB_OHCI_HCD_OMAP1
 	bool "OHCI support for OMAP1/2 chips"
-	depends on USB_OHCI_HCD && (ARCH_OMAP1 || ARCH_OMAP2)
+	depends on USB_OHCI_HCD && ARCH_OMAP1
 	default y
 	---help---
 	  Enables support for the OHCI controller on OMAP1/2 chips.

drivers/usb/host/ohci-omap.c

@@ -20,14 +20,15 @@
 #include <linux/clk.h>
 #include <linux/gpio.h>
 
-#include <mach/hardware.h>
 #include <asm/io.h>
 #include <asm/mach-types.h>
 
 #include <plat/mux.h>
-#include <mach/irqs.h>
 #include <plat/fpga.h>
-#include <plat/usb.h>
+
+#include <mach/hardware.h>
+#include <mach/irqs.h>
+#include <mach/usb.h>
 
 
 /* OMAP-1510 OHCI has its own MMU for DMA */

drivers/usb/otg/isp1301_omap.c

@@ -36,9 +36,9 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <plat/usb.h>
 #include <plat/mux.h>
 
+#include <mach/usb.h>
 
 #ifndef	DEBUG
 #undef	VERBOSE