Merge remote-tracking branches 'spi/topic/lp8841', 'spi/topic/msg',...

Merge remote-tracking branches 'spi/topic/lp8841', 'spi/topic/msg', 'spi/topic/pl022' and 'spi/topic/pxa2xx' into spi-next

Documentation/devicetree/bindings/spi/icpdas-lp8841-spi-rtc.txt

+* ICP DAS LP-8841 SPI Controller for RTC
+
+ICP DAS LP-8841 contains a DS-1302 RTC. RTC is connected to an IO
+memory register, which acts as an SPI master device.
+
+The device uses the standard MicroWire half-duplex transfer timing.
+Master output is set on low clock and sensed by the RTC on the rising
+edge. Master input is set by the RTC on the trailing edge and is sensed
+by the master on low clock.
+
+Required properties:
+
+- #address-cells: should be 1
+
+- #size-cells: should be 0
+
+- compatible: should be "icpdas,lp8841-spi-rtc"
+
+- reg: should provide IO memory address
+
+Requirements to SPI slave nodes:
+
+- There can be only one slave device.
+
+- The spi slave node should claim the following flags which are
+  required by the spi controller.
+
+  - spi-3wire: The master itself has only 3 wire. It cannor work in
+    full duplex mode.
+
+  - spi-cs-high: DS-1302 has active high chip select line. The master
+    doesn't support active low.
+
+  - spi-lsb-first: DS-1302 requires least significant bit first
+    transfers. The master only support this type of bit ordering.
+
+
+Example:
+
+spi@901c {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "icpdas,lp8841-spi-rtc";
+	reg = <0x901c 0x1>;
+
+	rtc@0 {
+		compatible = "maxim,ds1302";
+		reg = <0>;
+		spi-max-frequency = <500000>;
+		spi-3wire;
+		spi-lsb-first;
+		spi-cs-high;
+	};
+};

drivers/spi/Kconfig

@@ -294,6 +294,16 @@ config SPI_LM70_LLP
 	  which interfaces to an LM70 temperature sensor using
 	  a parallel port.
 
+config SPI_LP8841_RTC
+	tristate "ICP DAS LP-8841 SPI Controller for RTC"
+	depends on MACH_PXA27X_DT || COMPILE_TEST
+	help
+	  This driver provides an SPI master device to drive Maxim
+	  DS-1302 real time clock.
+
+	  Say N here unless you plan to run the kernel on an ICP DAS
+	  LP-8x4x industrial computer.
+
 config SPI_MPC52xx
 	tristate "Freescale MPC52xx SPI (non-PSC) controller support"
 	depends on PPC_MPC52xx
@@ -445,10 +455,6 @@ config SPI_PPC4xx
 	help
 	  This selects a driver for the PPC4xx SPI Controller.
 
-config SPI_PXA2XX_DMA
-	def_bool y
-	depends on SPI_PXA2XX
-
 config SPI_PXA2XX
 	tristate "PXA2xx SSP SPI master"
 	depends on (ARCH_PXA || PCI || ACPI)

drivers/spi/Makefile

@@ -47,6 +47,7 @@ obj-$(CONFIG_SPI_GPIO)			+= spi-gpio.o
 obj-$(CONFIG_SPI_IMG_SPFI)		+= spi-img-spfi.o
 obj-$(CONFIG_SPI_IMX)			+= spi-imx.o
 obj-$(CONFIG_SPI_LM70_LLP)		+= spi-lm70llp.o
+obj-$(CONFIG_SPI_LP8841_RTC)		+= spi-lp8841-rtc.o
 obj-$(CONFIG_SPI_MESON_SPIFC)		+= spi-meson-spifc.o
 obj-$(CONFIG_SPI_MPC512x_PSC)		+= spi-mpc512x-psc.o
 obj-$(CONFIG_SPI_MPC52xx_PSC)		+= spi-mpc52xx-psc.o
@@ -63,8 +64,7 @@ obj-$(CONFIG_SPI_TI_QSPI)		+= spi-ti-qspi.o
 obj-$(CONFIG_SPI_ORION)			+= spi-orion.o
 obj-$(CONFIG_SPI_PL022)			+= spi-pl022.o
 obj-$(CONFIG_SPI_PPC4xx)		+= spi-ppc4xx.o
-spi-pxa2xx-platform-objs		:= spi-pxa2xx.o
-spi-pxa2xx-platform-$(CONFIG_SPI_PXA2XX_DMA)	+= spi-pxa2xx-dma.o
+spi-pxa2xx-platform-objs		:= spi-pxa2xx.o spi-pxa2xx-dma.o
 obj-$(CONFIG_SPI_PXA2XX)		+= spi-pxa2xx-platform.o
 obj-$(CONFIG_SPI_PXA2XX_PCI)		+= spi-pxa2xx-pci.o
 obj-$(CONFIG_SPI_QUP)			+= spi-qup.o

drivers/spi/spi-lp8841-rtc.c

+/*
+ * SPI master driver for ICP DAS LP-8841 RTC
+ *
+ * Copyright (C) 2016 Sergei Ianovich
+ *
+ * based on
+ *
+ * Dallas DS1302 RTC Support
+ * Copyright (C) 2002 David McCullough
+ * Copyright (C) 2003 - 2007 Paul Mundt
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+#include <linux/delay.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/spi/spi.h>
+
+#define DRIVER_NAME	"spi_lp8841_rtc"
+
+#define SPI_LP8841_RTC_CE	0x01
+#define SPI_LP8841_RTC_CLK	0x02
+#define SPI_LP8841_RTC_nWE	0x04
+#define SPI_LP8841_RTC_MOSI	0x08
+#define SPI_LP8841_RTC_MISO	0x01
+
+/*
+ * REVISIT If there is support for SPI_3WIRE and SPI_LSB_FIRST in SPI
+ * GPIO driver, this SPI driver can be replaced by a simple GPIO driver
+ * providing 3 GPIO pins.
+ */
+
+struct spi_lp8841_rtc {
+	void		*iomem;
+	unsigned long	state;
+};
+
+static inline void
+setsck(struct spi_lp8841_rtc *data, int is_on)
+{
+	if (is_on)
+		data->state |= SPI_LP8841_RTC_CLK;
+	else
+		data->state &= ~SPI_LP8841_RTC_CLK;
+	writeb(data->state, data->iomem);
+}
+
+static inline void
+setmosi(struct spi_lp8841_rtc *data, int is_on)
+{
+	if (is_on)
+		data->state |= SPI_LP8841_RTC_MOSI;
+	else
+		data->state &= ~SPI_LP8841_RTC_MOSI;
+	writeb(data->state, data->iomem);
+}
+
+static inline int
+getmiso(struct spi_lp8841_rtc *data)
+{
+	return ioread8(data->iomem) & SPI_LP8841_RTC_MISO;
+}
+
+static inline u32
+bitbang_txrx_be_cpha0_lsb(struct spi_lp8841_rtc *data,
+		unsigned usecs, unsigned cpol, unsigned flags,
+		u32 word, u8 bits)
+{
+	/* if (cpol == 0) this is SPI_MODE_0; else this is SPI_MODE_2 */
+
+	u32 shift = 32 - bits;
+	/* clock starts at inactive polarity */
+	for (; likely(bits); bits--) {
+
+		/* setup LSB (to slave) on leading edge */
+		if ((flags & SPI_MASTER_NO_TX) == 0)
+			setmosi(data, (word & 1));
+
+		usleep_range(usecs, usecs + 1);	/* T(setup) */
+
+		/* sample LSB (from slave) on trailing edge */
+		word >>= 1;
+		if ((flags & SPI_MASTER_NO_RX) == 0)
+			word |= (getmiso(data) << 31);
+
+		setsck(data, !cpol);
+		usleep_range(usecs, usecs + 1);
+
+		setsck(data, cpol);
+	}
+
+	word >>= shift;
+	return word;
+}
+
+static int
+spi_lp8841_rtc_transfer_one(struct spi_master *master,
+			    struct spi_device *spi,
+			    struct spi_transfer *t)
+{
+	struct spi_lp8841_rtc	*data = spi_master_get_devdata(master);
+	unsigned		count = t->len;
+	const u8		*tx = t->tx_buf;
+	u8			*rx = t->rx_buf;
+	u8			word = 0;
+	int			ret = 0;
+
+	if (tx) {
+		data->state &= ~SPI_LP8841_RTC_nWE;
+		writeb(data->state, data->iomem);
+		while (likely(count > 0)) {
+			word = *tx++;
+			bitbang_txrx_be_cpha0_lsb(data, 1, 0,
+					SPI_MASTER_NO_RX, word, 8);
+			count--;
+		}
+	} else if (rx) {
+		data->state |= SPI_LP8841_RTC_nWE;
+		writeb(data->state, data->iomem);
+		while (likely(count > 0)) {
+			word = bitbang_txrx_be_cpha0_lsb(data, 1, 0,
+					SPI_MASTER_NO_TX, word, 8);
+			*rx++ = word;
+			count--;
+		}
+	} else {
+		ret = -EINVAL;
+	}
+
+	spi_finalize_current_transfer(master);
+
+	return ret;
+}
+
+static void
+spi_lp8841_rtc_set_cs(struct spi_device *spi, bool enable)
+{
+	struct spi_lp8841_rtc *data = spi_master_get_devdata(spi->master);
+
+	data->state = 0;
+	writeb(data->state, data->iomem);
+	if (enable) {
+		usleep_range(4, 5);
+		data->state |= SPI_LP8841_RTC_CE;
+		writeb(data->state, data->iomem);
+		usleep_range(4, 5);
+	}
+}
+
+static int
+spi_lp8841_rtc_setup(struct spi_device *spi)
+{
+	if ((spi->mode & SPI_CS_HIGH) == 0) {
+		dev_err(&spi->dev, "unsupported active low chip select\n");
+		return -EINVAL;
+	}
+
+	if ((spi->mode & SPI_LSB_FIRST) == 0) {
+		dev_err(&spi->dev, "unsupported MSB first mode\n");
+		return -EINVAL;
+	}
+
+	if ((spi->mode & SPI_3WIRE) == 0) {
+		dev_err(&spi->dev, "unsupported wiring. 3 wires required\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id spi_lp8841_rtc_dt_ids[] = {
+	{ .compatible = "icpdas,lp8841-spi-rtc" },
+	{ }
+};
+
+MODULE_DEVICE_TABLE(of, spi_lp8841_rtc_dt_ids);
+#endif
+
+static int
+spi_lp8841_rtc_probe(struct platform_device *pdev)
+{
+	int				ret;
+	struct spi_master		*master;
+	struct spi_lp8841_rtc		*data;
+	void				*iomem;
+
+	master = spi_alloc_master(&pdev->dev, sizeof(*data));
+	if (!master)
+		return -ENOMEM;
+	platform_set_drvdata(pdev, master);
+
+	master->flags = SPI_MASTER_HALF_DUPLEX;
+	master->mode_bits = SPI_CS_HIGH | SPI_3WIRE | SPI_LSB_FIRST;
+
+	master->bus_num = pdev->id;
+	master->num_chipselect = 1;
+	master->setup = spi_lp8841_rtc_setup;
+	master->set_cs = spi_lp8841_rtc_set_cs;
+	master->transfer_one = spi_lp8841_rtc_transfer_one;
+	master->bits_per_word_mask = SPI_BPW_MASK(8);
+#ifdef CONFIG_OF
+	master->dev.of_node = pdev->dev.of_node;
+#endif
+
+	data = spi_master_get_devdata(master);
+
+	iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	data->iomem = devm_ioremap_resource(&pdev->dev, iomem);
+	ret = PTR_ERR_OR_ZERO(data->iomem);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to get IO address\n");
+		goto err_put_master;
+	}
+
+	/* register with the SPI framework */
+	ret = devm_spi_register_master(&pdev->dev, master);
+	if (ret) {
+		dev_err(&pdev->dev, "cannot register spi master\n");
+		goto err_put_master;
+	}
+
+	return ret;
+
+
+err_put_master:
+	spi_master_put(master);
+
+	return ret;
+}
+
+MODULE_ALIAS("platform:" DRIVER_NAME);
+
+static struct platform_driver spi_lp8841_rtc_driver = {
+	.driver = {
+		.name	= DRIVER_NAME,
+		.of_match_table = of_match_ptr(spi_lp8841_rtc_dt_ids),
+	},
+	.probe		= spi_lp8841_rtc_probe,
+};
+module_platform_driver(spi_lp8841_rtc_driver);
+
+MODULE_DESCRIPTION("SPI master driver for ICP DAS LP-8841 RTC");
+MODULE_AUTHOR("Sergei Ianovich");
+MODULE_LICENSE("GPL");

drivers/spi/spi-pl022.c

@@ -346,13 +346,6 @@ struct vendor_data {
  * @clk: outgoing clock "SPICLK" for the SPI bus
  * @master: SPI framework hookup
  * @master_info: controller-specific data from machine setup
- * @kworker: thread struct for message pump
- * @kworker_task: pointer to task for message pump kworker thread
- * @pump_messages: work struct for scheduling work to the message pump
- * @queue_lock: spinlock to syncronise access to message queue
- * @queue: message queue
- * @busy: message pump is busy
- * @running: message pump is running
  * @pump_transfers: Tasklet used in Interrupt Transfer mode
  * @cur_msg: Pointer to current spi_message being processed
  * @cur_transfer: Pointer to current spi_transfer

drivers/spi/spi-pxa2xx-dma.c

@@ -254,8 +254,8 @@ irqreturn_t pxa2xx_spi_dma_transfer(struct driver_data *drv_data)
 	if (status & SSSR_ROR) {
 		dev_err(&drv_data->pdev->dev, "FIFO overrun\n");
 
-		dmaengine_terminate_all(drv_data->rx_chan);
-		dmaengine_terminate_all(drv_data->tx_chan);
+		dmaengine_terminate_async(drv_data->rx_chan);
+		dmaengine_terminate_async(drv_data->tx_chan);
 
 		pxa2xx_spi_dma_transfer_complete(drv_data, true);
 		return IRQ_HANDLED;
@@ -331,13 +331,13 @@ int pxa2xx_spi_dma_setup(struct driver_data *drv_data)
 void pxa2xx_spi_dma_release(struct driver_data *drv_data)
 {
 	if (drv_data->rx_chan) {
-		dmaengine_terminate_all(drv_data->rx_chan);
+		dmaengine_terminate_sync(drv_data->rx_chan);
 		dma_release_channel(drv_data->rx_chan);
 		sg_free_table(&drv_data->rx_sgt);
 		drv_data->rx_chan = NULL;
 	}
 	if (drv_data->tx_chan) {
-		dmaengine_terminate_all(drv_data->tx_chan);
+		dmaengine_terminate_sync(drv_data->tx_chan);
 		dma_release_channel(drv_data->tx_chan);
 		sg_free_table(&drv_data->tx_sgt);
 		drv_data->tx_chan = NULL;

drivers/spi/spi-pxa2xx-pci.c

@@ -19,6 +19,7 @@ enum {
 	PORT_BSW1,
 	PORT_BSW2,
 	PORT_QUARK_X1000,
+	PORT_LPT,
 };
 
 struct pxa_spi_info {
@@ -42,6 +43,9 @@ static struct dw_dma_slave bsw1_rx_param = { .src_id = 7 };
 static struct dw_dma_slave bsw2_tx_param = { .dst_id = 8 };
 static struct dw_dma_slave bsw2_rx_param = { .src_id = 9 };
 
+static struct dw_dma_slave lpt_tx_param = { .dst_id = 0 };
+static struct dw_dma_slave lpt_rx_param = { .src_id = 1 };
+
 static bool lpss_dma_filter(struct dma_chan *chan, void *param)
 {
 	struct dw_dma_slave *dws = param;
@@ -98,6 +102,14 @@ static struct pxa_spi_info spi_info_configs[] = {
 		.num_chipselect = 1,
 		.max_clk_rate = 50000000,
 	},
+	[PORT_LPT] = {
+		.type = LPSS_LPT_SSP,
+		.port_id = 0,
+		.num_chipselect = 1,
+		.max_clk_rate = 50000000,
+		.tx_param = &lpt_tx_param,
+		.rx_param = &lpt_rx_param,
+	},
 };
 
 static int pxa2xx_spi_pci_probe(struct pci_dev *dev,
@@ -202,6 +214,7 @@ static const struct pci_device_id pxa2xx_spi_pci_devices[] = {
 	{ PCI_VDEVICE(INTEL, 0x228e), PORT_BSW0 },
 	{ PCI_VDEVICE(INTEL, 0x2290), PORT_BSW1 },
 	{ PCI_VDEVICE(INTEL, 0x22ac), PORT_BSW2 },
+	{ PCI_VDEVICE(INTEL, 0x9ce6), PORT_LPT },
 	{ },
 };
 MODULE_DEVICE_TABLE(pci, pxa2xx_spi_pci_devices);

drivers/spi/spi-pxa2xx.c

@@ -65,8 +65,6 @@ MODULE_ALIAS("platform:pxa2xx-spi");
 #define LPSS_GENERAL_REG_RXTO_HOLDOFF_DISABLE	BIT(24)
 #define LPSS_CS_CONTROL_SW_MODE			BIT(0)
 #define LPSS_CS_CONTROL_CS_HIGH			BIT(1)
-#define LPSS_CS_CONTROL_CS_SEL_SHIFT		8
-#define LPSS_CS_CONTROL_CS_SEL_MASK		(3 << LPSS_CS_CONTROL_CS_SEL_SHIFT)
 #define LPSS_CAPS_CS_EN_SHIFT			9
 #define LPSS_CAPS_CS_EN_MASK			(0xf << LPSS_CAPS_CS_EN_SHIFT)
 
@@ -82,6 +80,10 @@ struct lpss_config {
 	u32 rx_threshold;
 	u32 tx_threshold_lo;
 	u32 tx_threshold_hi;
+	/* Chip select control */
+	unsigned cs_sel_shift;
+	unsigned cs_sel_mask;
+	unsigned cs_num;
 };
 
 /* Keep these sorted with enum pxa_ssp_type */
@@ -106,6 +108,19 @@ static const struct lpss_config lpss_platforms[] = {
 		.tx_threshold_lo = 160,
 		.tx_threshold_hi = 224,
 	},
+	{	/* LPSS_BSW_SSP */
+		.offset = 0x400,
+		.reg_general = 0x08,
+		.reg_ssp = 0x0c,
+		.reg_cs_ctrl = 0x18,
+		.reg_capabilities = -1,
+		.rx_threshold = 64,
+		.tx_threshold_lo = 160,
+		.tx_threshold_hi = 224,
+		.cs_sel_shift = 2,
+		.cs_sel_mask = 1 << 2,
+		.cs_num = 2,
+	},
 	{	/* LPSS_SPT_SSP */
 		.offset = 0x200,
 		.reg_general = -1,
@@ -125,6 +140,8 @@ static const struct lpss_config lpss_platforms[] = {
 		.rx_threshold = 1,
 		.tx_threshold_lo = 16,
 		.tx_threshold_hi = 48,
+		.cs_sel_shift = 8,
+		.cs_sel_mask = 3 << 8,
 	},
 };
 
@@ -139,6 +156,7 @@ static bool is_lpss_ssp(const struct driver_data *drv_data)
 	switch (drv_data->ssp_type) {
 	case LPSS_LPT_SSP:
 	case LPSS_BYT_SSP:
+	case LPSS_BSW_SSP:
 	case LPSS_SPT_SSP:
 	case LPSS_BXT_SSP:
 		return true;
@@ -288,37 +306,50 @@ static void lpss_ssp_setup(struct driver_data *drv_data)
 	}
 }
 
-static void lpss_ssp_cs_control(struct driver_data *drv_data, bool enable)
+static void lpss_ssp_select_cs(struct driver_data *drv_data,
+			       const struct lpss_config *config)
 {
-	const struct lpss_config *config;
 	u32 value, cs;
 
-	config = lpss_get_config(drv_data);
+	if (!config->cs_sel_mask)
+		return;
 
 	value = __lpss_ssp_read_priv(drv_data, config->reg_cs_ctrl);
-	if (enable) {
+
 	cs = drv_data->cur_msg->spi->chip_select;
-		cs <<= LPSS_CS_CONTROL_CS_SEL_SHIFT;
-		if (cs != (value & LPSS_CS_CONTROL_CS_SEL_MASK)) {
+	cs <<= config->cs_sel_shift;
+	if (cs != (value & config->cs_sel_mask)) {
 		/*
-			 * When switching another chip select output active
-			 * the output must be selected first and wait 2 ssp_clk
-			 * cycles before changing state to active. Otherwise
-			 * a short glitch will occur on the previous chip
-			 * select since output select is latched but state
-			 * control is not.
+		 * When switching another chip select output active the
+		 * output must be selected first and wait 2 ssp_clk cycles
+		 * before changing state to active. Otherwise a short
+		 * glitch will occur on the previous chip select since
+		 * output select is latched but state control is not.
 		 */
-			value &= ~LPSS_CS_CONTROL_CS_SEL_MASK;
+		value &= ~config->cs_sel_mask;
 		value |= cs;
 		__lpss_ssp_write_priv(drv_data,
 				      config->reg_cs_ctrl, value);
 		ndelay(1000000000 /
 		       (drv_data->master->max_speed_hz / 2));
 	}
+}
+
+static void lpss_ssp_cs_control(struct driver_data *drv_data, bool enable)
+{
+	const struct lpss_config *config;
+	u32 value;
+
+	config = lpss_get_config(drv_data);
+
+	if (enable)
+		lpss_ssp_select_cs(drv_data, config);
+
+	value = __lpss_ssp_read_priv(drv_data, config->reg_cs_ctrl);
+	if (enable)
 		value &= ~LPSS_CS_CONTROL_CS_HIGH;
-	} else {
+	else
 		value |= LPSS_CS_CONTROL_CS_HIGH;
-	}
 	__lpss_ssp_write_priv(drv_data, config->reg_cs_ctrl, value);
 }
 
@@ -496,6 +527,7 @@ static void giveback(struct driver_data *drv_data)
 {
 	struct spi_transfer* last_transfer;
 	struct spi_message *msg;
+	unsigned long timeout;
 
 	msg = drv_data->cur_msg;
 	drv_data->cur_msg = NULL;
@@ -508,6 +540,12 @@ static void giveback(struct driver_data *drv_data)
 	if (last_transfer->delay_usecs)
 		udelay(last_transfer->delay_usecs);
 
+	/* Wait until SSP becomes idle before deasserting the CS */
+	timeout = jiffies + msecs_to_jiffies(10);
+	while (pxa2xx_spi_read(drv_data, SSSR) & SSSR_BSY &&
+	       !time_after(jiffies, timeout))
+		cpu_relax();
+
 	/* Drop chip select UNLESS cs_change is true or we are returning
 	 * a message with an error, or next message is for another chip
 	 */
@@ -572,7 +610,7 @@ static void int_error_stop(struct driver_data *drv_data, const char* msg)
 
 static void int_transfer_complete(struct driver_data *drv_data)
 {
-	/* Stop SSP */
+	/* Clear and disable interrupts */
 	write_SSSR_CS(drv_data, drv_data->clear_sr);
 	reset_sccr1(drv_data);
 	if (!pxa25x_ssp_comp(drv_data))
@@ -957,8 +995,6 @@ static void pump_transfers(unsigned long data)
 	drv_data->tx_end = drv_data->tx + transfer->len;
 	drv_data->rx = transfer->rx_buf;
 	drv_data->rx_end = drv_data->rx + transfer->len;
-	drv_data->rx_dma = transfer->rx_dma;
-	drv_data->tx_dma = transfer->tx_dma;
 	drv_data->len = transfer->len;
 	drv_data->write = drv_data->tx ? chip->write : null_writer;
 	drv_data->read = drv_data->rx ? chip->read : null_reader;
@@ -1001,19 +1037,6 @@ static void pump_transfers(unsigned long data)
 					     "pump_transfers: DMA burst size reduced to match bits_per_word\n");
 	}
 
-	/* NOTE:  PXA25x_SSP _could_ use external clocking ... */
-	cr0 = pxa2xx_configure_sscr0(drv_data, clk_div, bits);
-	if (!pxa25x_ssp_comp(drv_data))
-		dev_dbg(&message->spi->dev, "%u Hz actual, %s\n",
-			drv_data->master->max_speed_hz
-				/ (1 + ((cr0 & SSCR0_SCR(0xfff)) >> 8)),
-			chip->enable_dma ? "DMA" : "PIO");
-	else
-		dev_dbg(&message->spi->dev, "%u Hz actual, %s\n",
-			drv_data->master->max_speed_hz / 2
-				/ (1 + ((cr0 & SSCR0_SCR(0x0ff)) >> 8)),
-			chip->enable_dma ? "DMA" : "PIO");
-
 	message->state = RUNNING_STATE;
 
 	drv_data->dma_mapped = 0;
@@ -1040,6 +1063,19 @@ static void pump_transfers(unsigned long data)
 		write_SSSR_CS(drv_data, drv_data->clear_sr);
 	}
 
+	/* NOTE:  PXA25x_SSP _could_ use external clocking ... */
+	cr0 = pxa2xx_configure_sscr0(drv_data, clk_div, bits);
+	if (!pxa25x_ssp_comp(drv_data))
+		dev_dbg(&message->spi->dev, "%u Hz actual, %s\n",
+			drv_data->master->max_speed_hz
+				/ (1 + ((cr0 & SSCR0_SCR(0xfff)) >> 8)),
+			drv_data->dma_mapped ? "DMA" : "PIO");
+	else
+		dev_dbg(&message->spi->dev, "%u Hz actual, %s\n",
+			drv_data->master->max_speed_hz / 2
+				/ (1 + ((cr0 & SSCR0_SCR(0x0ff)) >> 8)),
+			drv_data->dma_mapped ? "DMA" : "PIO");
+
 	if (is_lpss_ssp(drv_data)) {
 		if ((pxa2xx_spi_read(drv_data, SSIRF) & 0xff)
 		    != chip->lpss_rx_threshold)
@@ -1166,6 +1202,7 @@ static int setup(struct spi_device *spi)
 		break;
 	case LPSS_LPT_SSP:
 	case LPSS_BYT_SSP:
+	case LPSS_BSW_SSP:
 	case LPSS_SPT_SSP:
 	case LPSS_BXT_SSP:
 		config = lpss_get_config(drv_data);
@@ -1313,7 +1350,7 @@ static const struct acpi_device_id pxa2xx_spi_acpi_match[] = {
 	{ "INT3430", LPSS_LPT_SSP },
 	{ "INT3431", LPSS_LPT_SSP },
 	{ "80860F0E", LPSS_BYT_SSP },
-	{ "8086228E", LPSS_BYT_SSP },
+	{ "8086228E", LPSS_BSW_SSP },
 	{ },
 };
 MODULE_DEVICE_TABLE(acpi, pxa2xx_spi_acpi_match);
@@ -1347,10 +1384,14 @@ static const struct pci_device_id pxa2xx_spi_pci_compound_match[] = {
 	/* SPT-H */
 	{ PCI_VDEVICE(INTEL, 0xa129), LPSS_SPT_SSP },
 	{ PCI_VDEVICE(INTEL, 0xa12a), LPSS_SPT_SSP },
-	/* BXT */
+	/* BXT A-Step */
 	{ PCI_VDEVICE(INTEL, 0x0ac2), LPSS_BXT_SSP },
 	{ PCI_VDEVICE(INTEL, 0x0ac4), LPSS_BXT_SSP },
 	{ PCI_VDEVICE(INTEL, 0x0ac6), LPSS_BXT_SSP },
+	/* BXT B-Step */
+	{ PCI_VDEVICE(INTEL, 0x1ac2), LPSS_BXT_SSP },
+	{ PCI_VDEVICE(INTEL, 0x1ac4), LPSS_BXT_SSP },
+	{ PCI_VDEVICE(INTEL, 0x1ac6), LPSS_BXT_SSP },
 	/* APL */
 	{ PCI_VDEVICE(INTEL, 0x5ac2), LPSS_BXT_SSP },
 	{ PCI_VDEVICE(INTEL, 0x5ac4), LPSS_BXT_SSP },
@@ -1438,6 +1479,29 @@ pxa2xx_spi_init_pdata(struct platform_device *pdev)
 }
 #endif
 
+static int pxa2xx_spi_fw_translate_cs(struct spi_master *master, unsigned cs)
+{
+	struct driver_data *drv_data = spi_master_get_devdata(master);
+
+	if (has_acpi_companion(&drv_data->pdev->dev)) {
+		switch (drv_data->ssp_type) {
+		/*
+		 * For Atoms the ACPI DeviceSelection used by the Windows
+		 * driver starts from 1 instead of 0 so translate it here
+		 * to match what Linux expects.
+		 */
+		case LPSS_BYT_SSP:
+		case LPSS_BSW_SSP:
+			return cs - 1;
+
+		default:
+			break;
+		}
+	}
+
+	return cs;
+}
+
 static int pxa2xx_spi_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -1490,6 +1554,7 @@ static int pxa2xx_spi_probe(struct platform_device *pdev)
 	master->setup = setup;
 	master->transfer_one_message = pxa2xx_spi_transfer_one_message;
 	master->unprepare_transfer_hardware = pxa2xx_spi_unprepare_transfer;
+	master->fw_translate_cs = pxa2xx_spi_fw_translate_cs;
 	master->auto_runtime_pm = true;
 
 	drv_data->ssp_type = ssp->type;
@@ -1576,6 +1641,8 @@ static int pxa2xx_spi_probe(struct platform_device *pdev)
 			tmp &= LPSS_CAPS_CS_EN_MASK;
 			tmp >>= LPSS_CAPS_CS_EN_SHIFT;
 			platform_info->num_chipselect = ffz(tmp);
+		} else if (config->cs_num) {
+			platform_info->num_chipselect = config->cs_num;
 		}
 	}
 	master->num_chipselect = platform_info->num_chipselect;

drivers/spi/spi-pxa2xx.h

@@ -69,8 +69,6 @@ struct driver_data {
 	void *rx;
 	void *rx_end;
 	int dma_mapped;
-	dma_addr_t rx_dma;
-	dma_addr_t tx_dma;
 	size_t rx_map_len;
 	size_t tx_map_len;
 	u8 n_bytes;
@@ -147,20 +145,9 @@ static inline void write_SSSR_CS(struct driver_data *drv_data, u32 val)
 extern int pxa2xx_spi_flush(struct driver_data *drv_data);
 extern void *pxa2xx_spi_next_transfer(struct driver_data *drv_data);
 
-/*
- * Select the right DMA implementation.
- */
-#if defined(CONFIG_SPI_PXA2XX_DMA)
-#define SPI_PXA2XX_USE_DMA	1
 #define MAX_DMA_LEN		SZ_64K
 #define DEFAULT_DMA_CR1		(SSCR1_TSRE | SSCR1_RSRE | SSCR1_TRAIL)
-#else
-#undef SPI_PXA2XX_USE_DMA
-#define MAX_DMA_LEN		0
-#define DEFAULT_DMA_CR1		0
-#endif
 
-#ifdef SPI_PXA2XX_USE_DMA
 extern bool pxa2xx_spi_dma_is_possible(size_t len);
 extern int pxa2xx_spi_map_dma_buffers(struct driver_data *drv_data);
 extern irqreturn_t pxa2xx_spi_dma_transfer(struct driver_data *drv_data);
@@ -173,29 +160,5 @@ extern int pxa2xx_spi_set_dma_burst_and_threshold(struct chip_data *chip,
 						  u8 bits_per_word,
 						  u32 *burst_code,
 						  u32 *threshold);
-#else
-static inline bool pxa2xx_spi_dma_is_possible(size_t len) { return false; }
-static inline int pxa2xx_spi_map_dma_buffers(struct driver_data *drv_data)
-{
-	return 0;
-}
-#define pxa2xx_spi_dma_transfer NULL
-static inline void pxa2xx_spi_dma_prepare(struct driver_data *drv_data,
-					  u32 dma_burst) {}
-static inline void pxa2xx_spi_dma_start(struct driver_data *drv_data) {}
-static inline int pxa2xx_spi_dma_setup(struct driver_data *drv_data)
-{
-	return 0;
-}
-static inline void pxa2xx_spi_dma_release(struct driver_data *drv_data) {}
-static inline int pxa2xx_spi_set_dma_burst_and_threshold(struct chip_data *chip,
-							 struct spi_device *spi,
-							 u8 bits_per_word,
-							 u32 *burst_code,
-							 u32 *threshold)
-{
-	return -ENODEV;
-}
-#endif
 
 #endif /* SPI_PXA2XX_H */

include/linux/pxa2xx_ssp.h

@@ -197,6 +197,7 @@ enum pxa_ssp_type {
 	QUARK_X1000_SSP,
 	LPSS_LPT_SSP, /* Keep LPSS types sorted with lpss_platforms[] */
 	LPSS_BYT_SSP,
+	LPSS_BSW_SSP,
 	LPSS_SPT_SSP,
 	LPSS_BXT_SSP,
 };

include/linux/spi/spi.h

@@ -54,6 +54,10 @@ extern struct bus_type spi_bus_type;
  *
  * @transfer_bytes_histo:
  *                 transfer bytes histogramm
+ *
+ * @transfers_split_maxsize:
+ *                 number of transfers that have been split because of
+ *                 maxsize limit
  */
 struct spi_statistics {
 	spinlock_t		lock; /* lock for the whole structure */
@@ -73,6 +77,8 @@ struct spi_statistics {
 
 #define SPI_STATISTICS_HISTO_SIZE 17
 	unsigned long transfer_bytes_histo[SPI_STATISTICS_HISTO_SIZE];
+
+	unsigned long transfers_split_maxsize;
 };
 
 void spi_statistics_add_transfer_stats(struct spi_statistics *stats,
@@ -594,6 +600,37 @@ extern void spi_unregister_master(struct spi_master *master);
 
 extern struct spi_master *spi_busnum_to_master(u16 busnum);
 
+/*
+ * SPI resource management while processing a SPI message
+ */
+
+/**
+ * struct spi_res - spi resource management structure
+ * @entry:   list entry
+ * @release: release code called prior to freeing this resource
+ * @data:    extra data allocated for the specific use-case
+ *
+ * this is based on ideas from devres, but focused on life-cycle
+ * management during spi_message processing
+ */
+typedef void (*spi_res_release_t)(struct spi_master *master,
+				  struct spi_message *msg,
+				  void *res);
+struct spi_res {
+	struct list_head        entry;
+	spi_res_release_t       release;
+	unsigned long long      data[]; /* guarantee ull alignment */
+};
+
+extern void *spi_res_alloc(struct spi_device *spi,
+			   spi_res_release_t release,
+			   size_t size, gfp_t gfp);
+extern void spi_res_add(struct spi_message *message, void *res);
+extern void spi_res_free(void *res);
+
+extern void spi_res_release(struct spi_master *master,
+			    struct spi_message *message);
+
 /*---------------------------------------------------------------------------*/
 
 /*
@@ -732,6 +769,7 @@ struct spi_transfer {
  * @status: zero for success, else negative errno
  * @queue: for use by whichever driver currently owns the message
  * @state: for use by whichever driver currently owns the message
+ * @resources: for resource management when the spi message is processed
  *
  * A @spi_message is used to execute an atomic sequence of data transfers,
  * each represented by a struct spi_transfer.  The sequence is "atomic"
@@ -778,11 +816,15 @@ struct spi_message {
 	 */
 	struct list_head	queue;
 	void			*state;
+
+	/* list of spi_res reources when the spi message is processed */
+	struct list_head        resources;
 };
 
 static inline void spi_message_init_no_memset(struct spi_message *m)
 {
 	INIT_LIST_HEAD(&m->transfers);
+	INIT_LIST_HEAD(&m->resources);
 }
 
 static inline void spi_message_init(struct spi_message *m)
@@ -866,6 +908,60 @@ spi_max_transfer_size(struct spi_device *spi)
 
 /*---------------------------------------------------------------------------*/
 
+/* SPI transfer replacement methods which make use of spi_res */
+
+struct spi_replaced_transfers;
+typedef void (*spi_replaced_release_t)(struct spi_master *master,
+				       struct spi_message *msg,
+				       struct spi_replaced_transfers *res);
+/**
+ * struct spi_replaced_transfers - structure describing the spi_transfer
+ *                                 replacements that have occurred
+ *                                 so that they can get reverted
+ * @release:            some extra release code to get executed prior to
+ *                      relasing this structure
+ * @extradata:          pointer to some extra data if requested or NULL
+ * @replaced_transfers: transfers that have been replaced and which need
+ *                      to get restored
+ * @replaced_after:     the transfer after which the @replaced_transfers
+ *                      are to get re-inserted
+ * @inserted:           number of transfers inserted
+ * @inserted_transfers: array of spi_transfers of array-size @inserted,
+ *                      that have been replacing replaced_transfers
+ *
+ * note: that @extradata will point to @inserted_transfers[@inserted]
+ * if some extra allocation is requested, so alignment will be the same
+ * as for spi_transfers
+ */
+struct spi_replaced_transfers {
+	spi_replaced_release_t release;
+	void *extradata;
+	struct list_head replaced_transfers;
+	struct list_head *replaced_after;
+	size_t inserted;
+	struct spi_transfer inserted_transfers[];
+};
+
+extern struct spi_replaced_transfers *spi_replace_transfers(
+	struct spi_message *msg,
+	struct spi_transfer *xfer_first,
+	size_t remove,
+	size_t insert,
+	spi_replaced_release_t release,
+	size_t extradatasize,
+	gfp_t gfp);
+
+/*---------------------------------------------------------------------------*/
+
+/* SPI transfer transformation methods */
+
+extern int spi_split_transfers_maxsize(struct spi_master *master,
+				       struct spi_message *msg,
+				       size_t maxsize,
+				       gfp_t gfp);
+
+/*---------------------------------------------------------------------------*/
+
 /* All these synchronous SPI transfer routines are utilities layered
  * over the core async transfer primitive.  Here, "synchronous" means
  * they will sleep uninterruptibly until the async transfer completes.