regulator: bd71837: BD71837 PMIC regulator driver

Support for controlling the 8 bucks and 7 LDOs the PMIC contains.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

drivers/regulator/Kconfig

@@ -180,6 +180,17 @@ config REGULATOR_BCM590XX
 	  BCM590xx PMUs. This will enable support for the software
 	  controllable LDO/Switching regulators.
 
+config REGULATOR_BD71837
+	tristate "ROHM BD71837 Power Regulator"
+	depends on MFD_BD71837
+	help
+	  This driver supports voltage regulators on ROHM BD71837 PMIC.
+	  This will enable support for the software controllable buck
+	  and LDO regulators.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called bd71837-regulator.
+
 config REGULATOR_BD9571MWV
 	tristate "ROHM BD9571MWV Regulators"
 	depends on MFD_BD9571MWV

drivers/regulator/Makefile

@@ -27,6 +27,7 @@ obj-$(CONFIG_REGULATOR_AS3711) += as3711-regulator.o
 obj-$(CONFIG_REGULATOR_AS3722) += as3722-regulator.o
 obj-$(CONFIG_REGULATOR_AXP20X) += axp20x-regulator.o
 obj-$(CONFIG_REGULATOR_BCM590XX) += bcm590xx-regulator.o
+obj-$(CONFIG_REGULATOR_BD71837) += bd71837-regulator.o
 obj-$(CONFIG_REGULATOR_BD9571MWV) += bd9571mwv-regulator.o
 obj-$(CONFIG_REGULATOR_DA903X)	+= da903x.o
 obj-$(CONFIG_REGULATOR_DA9052)	+= da9052-regulator.o

drivers/regulator/bd71837-regulator.c

+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2018 ROHM Semiconductors
+// bd71837-regulator.c ROHM BD71837MWV regulator driver
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/gpio.h>
+#include <linux/mfd/bd71837.h>
+#include <linux/regulator/of_regulator.h>
+
+struct bd71837_pmic {
+	struct regulator_desc descs[BD71837_REGULATOR_CNT];
+	struct bd71837 *mfd;
+	struct platform_device *pdev;
+	struct regulator_dev *rdev[BD71837_REGULATOR_CNT];
+};
+
+/*
+ * BUCK1/2/3/4
+ * BUCK1RAMPRATE[1:0] BUCK1 DVS ramp rate setting
+ * 00: 10.00mV/usec 10mV 1uS
+ * 01: 5.00mV/usec	10mV 2uS
+ * 10: 2.50mV/usec	10mV 4uS
+ * 11: 1.25mV/usec	10mV 8uS
+ */
+static int bd71837_buck1234_set_ramp_delay(struct regulator_dev *rdev,
+					   int ramp_delay)
+{
+	struct bd71837_pmic *pmic = rdev_get_drvdata(rdev);
+	struct bd71837 *mfd = pmic->mfd;
+	int id = rdev->desc->id;
+	unsigned int ramp_value = BUCK_RAMPRATE_10P00MV;
+
+	dev_dbg(&(pmic->pdev->dev), "Buck[%d] Set Ramp = %d\n", id + 1,
+		ramp_delay);
+	switch (ramp_delay) {
+	case 1 ... 1250:
+		ramp_value = BUCK_RAMPRATE_1P25MV;
+		break;
+	case 1251 ... 2500:
+		ramp_value = BUCK_RAMPRATE_2P50MV;
+		break;
+	case 2501 ... 5000:
+		ramp_value = BUCK_RAMPRATE_5P00MV;
+		break;
+	case 5001 ... 10000:
+		ramp_value = BUCK_RAMPRATE_10P00MV;
+		break;
+	default:
+		ramp_value = BUCK_RAMPRATE_10P00MV;
+		dev_err(&pmic->pdev->dev,
+			"%s: ramp_delay: %d not supported, setting 10000mV//us\n",
+			rdev->desc->name, ramp_delay);
+	}
+
+	return regmap_update_bits(mfd->regmap, BD71837_REG_BUCK1_CTRL + id,
+				  BUCK_RAMPRATE_MASK, ramp_value << 6);
+}
+
+/* Bucks 1 to 4 support DVS. PWM mode is used when voltage is changed.
+ * Bucks 5 to 8 and LDOs can use PFM and must be disabled when voltage
+ * is changed. Hence we return -EBUSY for these if voltage is changed
+ * when BUCK/LDO is enabled.
+ */
+static int bd71837_set_voltage_sel_restricted(struct regulator_dev *rdev,
+						    unsigned int sel)
+{
+	int ret;
+
+	ret = regulator_is_enabled_regmap(rdev);
+	if (!ret)
+		ret = regulator_set_voltage_sel_regmap(rdev, sel);
+	else if (ret == 1)
+		ret = -EBUSY;
+	return ret;
+}
+
+static struct regulator_ops bd71837_ldo_regulator_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.list_voltage = regulator_list_voltage_linear_range,
+	.set_voltage_sel = bd71837_set_voltage_sel_restricted,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+};
+
+static struct regulator_ops bd71837_ldo_regulator_nolinear_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.list_voltage = regulator_list_voltage_table,
+	.set_voltage_sel = bd71837_set_voltage_sel_restricted,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+};
+
+static struct regulator_ops bd71837_buck_regulator_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.list_voltage = regulator_list_voltage_linear_range,
+	.set_voltage_sel = bd71837_set_voltage_sel_restricted,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.set_voltage_time_sel = regulator_set_voltage_time_sel,
+};
+
+static struct regulator_ops bd71837_buck_regulator_nolinear_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.list_voltage = regulator_list_voltage_table,
+	.set_voltage_sel = bd71837_set_voltage_sel_restricted,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.set_voltage_time_sel = regulator_set_voltage_time_sel,
+};
+
+static struct regulator_ops bd71837_buck1234_regulator_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.list_voltage = regulator_list_voltage_linear_range,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.set_voltage_time_sel = regulator_set_voltage_time_sel,
+	.set_ramp_delay = bd71837_buck1234_set_ramp_delay,
+};
+
+/*
+ * BUCK1/2/3/4
+ * 0.70 to 1.30V (10mV step)
+ */
+static const struct regulator_linear_range bd71837_buck1234_voltage_ranges[] = {
+	REGULATOR_LINEAR_RANGE(700000, 0x00, 0x3C, 10000),
+	REGULATOR_LINEAR_RANGE(1300000, 0x3D, 0x3F, 0),
+};
+
+/*
+ * BUCK5
+ * 0.9V to 1.35V ()
+ */
+static const struct regulator_linear_range bd71837_buck5_voltage_ranges[] = {
+	REGULATOR_LINEAR_RANGE(700000, 0x00, 0x03, 100000),
+	REGULATOR_LINEAR_RANGE(1050000, 0x04, 0x05, 50000),
+	REGULATOR_LINEAR_RANGE(1200000, 0x06, 0x07, 150000),
+};
+
+/*
+ * BUCK6
+ * 3.0V to 3.3V (step 100mV)
+ */
+static const struct regulator_linear_range bd71837_buck6_voltage_ranges[] = {
+	REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000),
+};
+
+/*
+ * BUCK7
+ * 000 = 1.605V
+ * 001 = 1.695V
+ * 010 = 1.755V
+ * 011 = 1.8V (Initial)
+ * 100 = 1.845V
+ * 101 = 1.905V
+ * 110 = 1.95V
+ * 111 = 1.995V
+ */
+static const unsigned int buck_7_volts[] = {
+	1605000, 1695000, 1755000, 1800000, 1845000, 1905000, 1950000, 1995000
+};
+
+/*
+ * BUCK8
+ * 0.8V to 1.40V (step 10mV)
+ */
+static const struct regulator_linear_range bd71837_buck8_voltage_ranges[] = {
+	REGULATOR_LINEAR_RANGE(800000, 0x00, 0x3C, 10000),
+	REGULATOR_LINEAR_RANGE(1400000, 0x3D, 0x3F, 0),
+};
+
+/*
+ * LDO1
+ * 3.0 to 3.3V (100mV step)
+ */
+static const struct regulator_linear_range bd71837_ldo1_voltage_ranges[] = {
+	REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000),
+};
+
+/*
+ * LDO2
+ * 0.8 or 0.9V
+ */
+const unsigned int ldo_2_volts[] = {
+	900000, 800000
+};
+
+/*
+ * LDO3
+ * 1.8 to 3.3V (100mV step)
+ */
+static const struct regulator_linear_range bd71837_ldo3_voltage_ranges[] = {
+	REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
+};
+
+/*
+ * LDO4
+ * 0.9 to 1.8V (100mV step)
+ */
+static const struct regulator_linear_range bd71837_ldo4_voltage_ranges[] = {
+	REGULATOR_LINEAR_RANGE(900000, 0x00, 0x09, 100000),
+	REGULATOR_LINEAR_RANGE(1800000, 0x0A, 0x0F, 0),
+};
+
+/*
+ * LDO5
+ * 1.8 to 3.3V (100mV step)
+ */
+static const struct regulator_linear_range bd71837_ldo5_voltage_ranges[] = {
+	REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
+};
+
+/*
+ * LDO6
+ * 0.9 to 1.8V (100mV step)
+ */
+static const struct regulator_linear_range bd71837_ldo6_voltage_ranges[] = {
+	REGULATOR_LINEAR_RANGE(900000, 0x00, 0x09, 100000),
+	REGULATOR_LINEAR_RANGE(1800000, 0x0A, 0x0F, 0),
+};
+
+/*
+ * LDO7
+ * 1.8 to 3.3V (100mV step)
+ */
+static const struct regulator_linear_range bd71837_ldo7_voltage_ranges[] = {
+	REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
+};
+
+static const struct regulator_desc bd71837_regulators[] = {
+	{
+		.name = "buck1",
+		.of_match = of_match_ptr("BUCK1"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD71837_BUCK1,
+		.ops = &bd71837_buck1234_regulator_ops,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = BD71837_BUCK1_VOLTAGE_NUM,
+		.linear_ranges = bd71837_buck1234_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(bd71837_buck1234_voltage_ranges),
+		.vsel_reg = BD71837_REG_BUCK1_VOLT_RUN,
+		.vsel_mask = BUCK1_RUN_MASK,
+		.enable_reg = BD71837_REG_BUCK1_CTRL,
+		.enable_mask = BD71837_BUCK_EN,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "buck2",
+		.of_match = of_match_ptr("BUCK2"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD71837_BUCK2,
+		.ops = &bd71837_buck1234_regulator_ops,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = BD71837_BUCK2_VOLTAGE_NUM,
+		.linear_ranges = bd71837_buck1234_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(bd71837_buck1234_voltage_ranges),
+		.vsel_reg = BD71837_REG_BUCK2_VOLT_RUN,
+		.vsel_mask = BUCK2_RUN_MASK,
+		.enable_reg = BD71837_REG_BUCK2_CTRL,
+		.enable_mask = BD71837_BUCK_EN,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "buck3",
+		.of_match = of_match_ptr("BUCK3"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD71837_BUCK3,
+		.ops = &bd71837_buck1234_regulator_ops,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = BD71837_BUCK3_VOLTAGE_NUM,
+		.linear_ranges = bd71837_buck1234_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(bd71837_buck1234_voltage_ranges),
+		.vsel_reg = BD71837_REG_BUCK3_VOLT_RUN,
+		.vsel_mask = BUCK3_RUN_MASK,
+		.enable_reg = BD71837_REG_BUCK3_CTRL,
+		.enable_mask = BD71837_BUCK_EN,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "buck4",
+		.of_match = of_match_ptr("BUCK4"),
+		.regulators_node = of_match_ptr("regulators"),
+			.id = BD71837_BUCK4,
+		.ops = &bd71837_buck1234_regulator_ops,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = BD71837_BUCK4_VOLTAGE_NUM,
+		.linear_ranges = bd71837_buck1234_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(bd71837_buck1234_voltage_ranges),
+		.vsel_reg = BD71837_REG_BUCK4_VOLT_RUN,
+		.vsel_mask = BUCK4_RUN_MASK,
+		.enable_reg = BD71837_REG_BUCK4_CTRL,
+		.enable_mask = BD71837_BUCK_EN,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "buck5",
+		.of_match = of_match_ptr("BUCK5"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD71837_BUCK5,
+		.ops = &bd71837_buck_regulator_ops,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = BD71837_BUCK5_VOLTAGE_NUM,
+		.linear_ranges = bd71837_buck5_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(bd71837_buck5_voltage_ranges),
+		.vsel_reg = BD71837_REG_BUCK5_VOLT,
+		.vsel_mask = BUCK5_MASK,
+		.enable_reg = BD71837_REG_BUCK5_CTRL,
+		.enable_mask = BD71837_BUCK_EN,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "buck6",
+		.of_match = of_match_ptr("BUCK6"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD71837_BUCK6,
+		.ops = &bd71837_buck_regulator_ops,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = BD71837_BUCK6_VOLTAGE_NUM,
+		.linear_ranges = bd71837_buck6_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(bd71837_buck6_voltage_ranges),
+		.vsel_reg = BD71837_REG_BUCK6_VOLT,
+		.vsel_mask = BUCK6_MASK,
+		.enable_reg = BD71837_REG_BUCK6_CTRL,
+		.enable_mask = BD71837_BUCK_EN,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "buck7",
+		.of_match = of_match_ptr("BUCK7"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD71837_BUCK7,
+		.ops = &bd71837_buck_regulator_nolinear_ops,
+		.type = REGULATOR_VOLTAGE,
+		.volt_table = &buck_7_volts[0],
+		.n_voltages = ARRAY_SIZE(buck_7_volts),
+		.vsel_reg = BD71837_REG_BUCK7_VOLT,
+		.vsel_mask = BUCK7_MASK,
+		.enable_reg = BD71837_REG_BUCK7_CTRL,
+		.enable_mask = BD71837_BUCK_EN,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "buck8",
+		.of_match = of_match_ptr("BUCK8"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD71837_BUCK8,
+		.ops = &bd71837_buck_regulator_ops,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = BD71837_BUCK8_VOLTAGE_NUM,
+		.linear_ranges = bd71837_buck8_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(bd71837_buck8_voltage_ranges),
+		.vsel_reg = BD71837_REG_BUCK8_VOLT,
+		.vsel_mask = BUCK8_MASK,
+		.enable_reg = BD71837_REG_BUCK8_CTRL,
+		.enable_mask = BD71837_BUCK_EN,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "ldo1",
+		.of_match = of_match_ptr("LDO1"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD71837_LDO1,
+		.ops = &bd71837_ldo_regulator_ops,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = BD71837_LDO1_VOLTAGE_NUM,
+		.linear_ranges = bd71837_ldo1_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(bd71837_ldo1_voltage_ranges),
+		.vsel_reg = BD71837_REG_LDO1_VOLT,
+		.vsel_mask = LDO1_MASK,
+		.enable_reg = BD71837_REG_LDO1_VOLT,
+		.enable_mask = BD71837_LDO_EN,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "ldo2",
+		.of_match = of_match_ptr("LDO2"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD71837_LDO2,
+		.ops = &bd71837_ldo_regulator_nolinear_ops,
+		.type = REGULATOR_VOLTAGE,
+		.volt_table = &ldo_2_volts[0],
+		.vsel_reg = BD71837_REG_LDO2_VOLT,
+		.vsel_mask = LDO2_MASK,
+		.n_voltages = ARRAY_SIZE(ldo_2_volts),
+		.n_voltages = BD71837_LDO2_VOLTAGE_NUM,
+		.enable_reg = BD71837_REG_LDO2_VOLT,
+		.enable_mask = BD71837_LDO_EN,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "ldo3",
+		.of_match = of_match_ptr("LDO3"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD71837_LDO3,
+		.ops = &bd71837_ldo_regulator_ops,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = BD71837_LDO3_VOLTAGE_NUM,
+		.linear_ranges = bd71837_ldo3_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(bd71837_ldo3_voltage_ranges),
+		.vsel_reg = BD71837_REG_LDO3_VOLT,
+		.vsel_mask = LDO3_MASK,
+		.enable_reg = BD71837_REG_LDO3_VOLT,
+		.enable_mask = BD71837_LDO_EN,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "ldo4",
+		.of_match = of_match_ptr("LDO4"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD71837_LDO4,
+		.ops = &bd71837_ldo_regulator_ops,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = BD71837_LDO4_VOLTAGE_NUM,
+		.linear_ranges = bd71837_ldo4_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(bd71837_ldo4_voltage_ranges),
+		.vsel_reg = BD71837_REG_LDO4_VOLT,
+		.vsel_mask = LDO4_MASK,
+		.enable_reg = BD71837_REG_LDO4_VOLT,
+		.enable_mask = BD71837_LDO_EN,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "ldo5",
+		.of_match = of_match_ptr("LDO5"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD71837_LDO5,
+		.ops = &bd71837_ldo_regulator_ops,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = BD71837_LDO5_VOLTAGE_NUM,
+		.linear_ranges = bd71837_ldo5_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(bd71837_ldo5_voltage_ranges),
+		/* LDO5 is supplied by buck6 */
+		.supply_name = "buck6",
+		.vsel_reg = BD71837_REG_LDO5_VOLT,
+		.vsel_mask = LDO5_MASK,
+		.enable_reg = BD71837_REG_LDO5_VOLT,
+		.enable_mask = BD71837_LDO_EN,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "ldo6",
+		.of_match = of_match_ptr("LDO6"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD71837_LDO6,
+		.ops = &bd71837_ldo_regulator_ops,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = BD71837_LDO6_VOLTAGE_NUM,
+		.linear_ranges = bd71837_ldo6_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(bd71837_ldo6_voltage_ranges),
+		/* LDO6 is supplied by buck7 */
+		.supply_name = "buck7",
+		.vsel_reg = BD71837_REG_LDO6_VOLT,
+		.vsel_mask = LDO6_MASK,
+		.enable_reg = BD71837_REG_LDO6_VOLT,
+		.enable_mask = BD71837_LDO_EN,
+		.owner = THIS_MODULE,
+	},
+	{
+		.name = "ldo7",
+		.of_match = of_match_ptr("LDO7"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = BD71837_LDO7,
+		.ops = &bd71837_ldo_regulator_ops,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = BD71837_LDO7_VOLTAGE_NUM,
+		.linear_ranges = bd71837_ldo7_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(bd71837_ldo7_voltage_ranges),
+		.vsel_reg = BD71837_REG_LDO7_VOLT,
+		.vsel_mask = LDO7_MASK,
+		.enable_reg = BD71837_REG_LDO7_VOLT,
+		.enable_mask = BD71837_LDO_EN,
+		.owner = THIS_MODULE,
+	},
+};
+
+struct reg_init {
+	unsigned int reg;
+	unsigned int mask;
+};
+
+static int bd71837_probe(struct platform_device *pdev)
+{
+	struct bd71837_pmic *pmic;
+	struct bd71837_board *pdata;
+	struct regulator_config config = { 0 };
+	struct reg_init pmic_regulator_inits[] = {
+		{
+			.reg = BD71837_REG_BUCK1_CTRL,
+			.mask = BD71837_BUCK_SEL,
+		}, {
+			.reg = BD71837_REG_BUCK2_CTRL,
+			.mask = BD71837_BUCK_SEL,
+		}, {
+			.reg = BD71837_REG_BUCK3_CTRL,
+			.mask = BD71837_BUCK_SEL,
+		}, {
+			.reg = BD71837_REG_BUCK4_CTRL,
+			.mask = BD71837_BUCK_SEL,
+		}, {
+			.reg = BD71837_REG_BUCK5_CTRL,
+			.mask = BD71837_BUCK_SEL,
+		}, {
+			.reg = BD71837_REG_BUCK6_CTRL,
+			.mask = BD71837_BUCK_SEL,
+		}, {
+			.reg = BD71837_REG_BUCK7_CTRL,
+			.mask = BD71837_BUCK_SEL,
+		}, {
+			.reg = BD71837_REG_BUCK8_CTRL,
+			.mask = BD71837_BUCK_SEL,
+		}, {
+			.reg = BD71837_REG_LDO1_VOLT,
+			.mask = BD71837_LDO_SEL,
+		}, {
+			.reg = BD71837_REG_LDO2_VOLT,
+			.mask = BD71837_LDO_SEL,
+		}, {
+			.reg = BD71837_REG_LDO3_VOLT,
+			.mask = BD71837_LDO_SEL,
+		}, {
+			.reg = BD71837_REG_LDO4_VOLT,
+			.mask = BD71837_LDO_SEL,
+		}, {
+			.reg = BD71837_REG_LDO5_VOLT,
+			.mask = BD71837_LDO_SEL,
+		}, {
+			.reg = BD71837_REG_LDO6_VOLT,
+			.mask = BD71837_LDO_SEL,
+		}, {
+			.reg = BD71837_REG_LDO7_VOLT,
+			.mask = BD71837_LDO_SEL,
+		}
+	};
+
+	int i, err;
+
+	pmic = devm_kzalloc(&pdev->dev, sizeof(struct bd71837_pmic),
+			    GFP_KERNEL);
+	if (!pmic)
+		return -ENOMEM;
+
+	memcpy(pmic->descs, bd71837_regulators, sizeof(pmic->descs));
+
+	pmic->pdev = pdev;
+	pmic->mfd = dev_get_drvdata(pdev->dev.parent);
+
+	if (!pmic->mfd) {
+		dev_err(&pdev->dev, "No MFD driver data\n");
+		err = -EINVAL;
+		goto err;
+	}
+	platform_set_drvdata(pdev, pmic);
+	pdata = dev_get_platdata(pmic->mfd->dev);
+
+	/* Register LOCK release */
+	err = regmap_update_bits(pmic->mfd->regmap, BD71837_REG_REGLOCK,
+				 (REGLOCK_PWRSEQ | REGLOCK_VREG), 0);
+	if (err) {
+		dev_err(&pmic->pdev->dev, "Failed to unlock PMIC (%d)\n", err);
+		goto err;
+	} else {
+		dev_dbg(&pmic->pdev->dev, "%s: Unlocked lock register 0x%x\n",
+			__func__, BD71837_REG_REGLOCK);
+	}
+
+	for (i = 0; i < ARRAY_SIZE(pmic_regulator_inits); i++) {
+
+		struct regulator_desc *desc;
+		struct regulator_dev *rdev;
+
+		desc = &pmic->descs[i];
+
+		if (pdata)
+			config.init_data = pdata->init_data[i];
+
+		config.dev = pdev->dev.parent;
+		config.driver_data = pmic;
+		config.regmap = pmic->mfd->regmap;
+
+		rdev = devm_regulator_register(&pdev->dev, desc, &config);
+		if (IS_ERR(rdev)) {
+			dev_err(pmic->mfd->dev,
+				"failed to register %s regulator\n",
+				desc->name);
+			err = PTR_ERR(rdev);
+			goto err;
+		}
+		/* Regulator register gets the regulator constraints and
+		 * applies them (set_machine_constraints). This should have
+		 * turned the control register(s) to correct values and we
+		 * can now switch the control from PMIC state machine to the
+		 * register interface
+		 */
+		err = regmap_update_bits(pmic->mfd->regmap,
+					 pmic_regulator_inits[i].reg,
+					 pmic_regulator_inits[i].mask,
+					 0xFFFFFFFF);
+		if (err) {
+			dev_err(&pmic->pdev->dev,
+				"Failed to write BUCK/LDO SEL bit for (%s)\n",
+				desc->name);
+			goto err;
+		}
+
+		pmic->rdev[i] = rdev;
+	}
+
+	return 0;
+
+err:
+	return err;
+}
+
+static struct platform_driver bd71837_regulator = {
+	.driver = {
+		.name = "bd71837-pmic",
+		.owner = THIS_MODULE,
+	},
+	.probe = bd71837_probe,
+};
+
+module_platform_driver(bd71837_regulator);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("BD71837 voltage regulator driver");
+MODULE_LICENSE("GPL");