Commit beb0dff1 authored by Jacob Keller's avatar Jacob Keller Committed by Jeff Kirsher

i40e: enable PTP

New feature: Enable PTP support in the i40e driver.

Change-ID: I6a8e799f582705191f9583afb1b9231a8db96cc8
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: default avatarMatthew Vick <matthew.vick@intel.com>
Signed-off-by: default avatarJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: default avatarJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
parent 6ff4ef86
......@@ -243,6 +243,7 @@ config IXGBEVF
config I40E
tristate "Intel(R) Ethernet Controller XL710 Family support"
select PTP_1588_CLOCK
depends on PCI
---help---
This driver supports Intel(R) Ethernet Controller XL710 Family of
......
......@@ -40,4 +40,5 @@ i40e-objs := i40e_main.o \
i40e_debugfs.o \
i40e_diag.o \
i40e_txrx.o \
i40e_ptp.o \
i40e_virtchnl_pf.o
......@@ -50,6 +50,9 @@
#include <net/ip6_checksum.h>
#include <linux/ethtool.h>
#include <linux/if_vlan.h>
#include <linux/clocksource.h>
#include <linux/net_tstamp.h>
#include <linux/ptp_clock_kernel.h>
#include "i40e_type.h"
#include "i40e_prototype.h"
#include "i40e_virtchnl.h"
......@@ -242,6 +245,7 @@ struct i40e_pf {
#define I40E_FLAG_DCB_ENABLED (u64)(1 << 20)
#define I40E_FLAG_FDIR_ENABLED (u64)(1 << 21)
#define I40E_FLAG_FDIR_ATR_ENABLED (u64)(1 << 22)
#define I40E_FLAG_PTP (u64)(1 << 25)
#define I40E_FLAG_MFP_ENABLED (u64)(1 << 26)
#ifdef CONFIG_I40E_VXLAN
#define I40E_FLAG_VXLAN_FILTER_SYNC (u64)(1 << 27)
......@@ -302,6 +306,20 @@ struct i40e_pf {
u32 fcoe_hmc_filt_num;
u32 fcoe_hmc_cntx_num;
struct i40e_filter_control_settings filter_settings;
struct ptp_clock *ptp_clock;
struct ptp_clock_info ptp_caps;
struct sk_buff *ptp_tx_skb;
struct work_struct ptp_tx_work;
struct hwtstamp_config tstamp_config;
unsigned long ptp_tx_start;
unsigned long last_rx_ptp_check;
spinlock_t tmreg_lock; /* Used to protect the device time registers. */
u64 ptp_base_adj;
u32 tx_hwtstamp_timeouts;
u32 rx_hwtstamp_cleared;
bool ptp_tx;
bool ptp_rx;
};
struct i40e_mac_filter {
......@@ -566,4 +584,12 @@ struct i40e_mac_filter *i40e_find_mac(struct i40e_vsi *vsi, u8 *macaddr,
bool is_vf, bool is_netdev);
void i40e_vlan_stripping_enable(struct i40e_vsi *vsi);
void i40e_ptp_rx_hang(struct i40e_vsi *vsi);
void i40e_ptp_tx_hwtstamp(struct i40e_pf *pf);
void i40e_ptp_rx_hwtstamp(struct i40e_pf *pf, struct sk_buff *skb, u8 index);
void i40e_ptp_set_increment(struct i40e_pf *pf);
int i40e_ptp_set_ts_config(struct i40e_pf *pf, struct ifreq *ifr);
int i40e_ptp_get_ts_config(struct i40e_pf *pf, struct ifreq *ifr);
void i40e_ptp_init(struct i40e_pf *pf);
void i40e_ptp_stop(struct i40e_pf *pf);
#endif /* _I40E_H_ */
......@@ -108,6 +108,8 @@ static struct i40e_stats i40e_gstrings_stats[] = {
I40E_PF_STAT("rx_oversize", stats.rx_oversize),
I40E_PF_STAT("rx_jabber", stats.rx_jabber),
I40E_PF_STAT("VF_admin_queue_requests", vf_aq_requests),
I40E_PF_STAT("tx_hwtstamp_timeouts", tx_hwtstamp_timeouts),
I40E_PF_STAT("rx_hwtstamp_cleared", rx_hwtstamp_cleared),
};
#define I40E_QUEUE_STATS_LEN(n) \
......@@ -748,7 +750,36 @@ static void i40e_get_strings(struct net_device *netdev, u32 stringset,
static int i40e_get_ts_info(struct net_device *dev,
struct ethtool_ts_info *info)
{
return ethtool_op_get_ts_info(dev, info);
struct i40e_pf *pf = i40e_netdev_to_pf(dev);
info->so_timestamping = SOF_TIMESTAMPING_TX_SOFTWARE |
SOF_TIMESTAMPING_RX_SOFTWARE |
SOF_TIMESTAMPING_SOFTWARE |
SOF_TIMESTAMPING_TX_HARDWARE |
SOF_TIMESTAMPING_RX_HARDWARE |
SOF_TIMESTAMPING_RAW_HARDWARE;
if (pf->ptp_clock)
info->phc_index = ptp_clock_index(pf->ptp_clock);
else
info->phc_index = -1;
info->tx_types = (1 << HWTSTAMP_TX_OFF) | (1 << HWTSTAMP_TX_ON);
info->rx_filters = (1 << HWTSTAMP_FILTER_NONE) |
(1 << HWTSTAMP_FILTER_PTP_V1_L4_SYNC) |
(1 << HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ) |
(1 << HWTSTAMP_FILTER_PTP_V2_EVENT) |
(1 << HWTSTAMP_FILTER_PTP_V2_L2_EVENT) |
(1 << HWTSTAMP_FILTER_PTP_V2_L4_EVENT) |
(1 << HWTSTAMP_FILTER_PTP_V2_SYNC) |
(1 << HWTSTAMP_FILTER_PTP_V2_L2_SYNC) |
(1 << HWTSTAMP_FILTER_PTP_V2_L4_SYNC) |
(1 << HWTSTAMP_FILTER_PTP_V2_DELAY_REQ) |
(1 << HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ) |
(1 << HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ);
return 0;
}
static int i40e_link_test(struct net_device *netdev, u64 *data)
......
......@@ -1697,6 +1697,27 @@ static int i40e_change_mtu(struct net_device *netdev, int new_mtu)
return 0;
}
/**
* i40e_ioctl - Access the hwtstamp interface
* @netdev: network interface device structure
* @ifr: interface request data
* @cmd: ioctl command
**/
int i40e_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
{
struct i40e_netdev_priv *np = netdev_priv(netdev);
struct i40e_pf *pf = np->vsi->back;
switch (cmd) {
case SIOCGHWTSTAMP:
return i40e_ptp_get_ts_config(pf, ifr);
case SIOCSHWTSTAMP:
return i40e_ptp_set_ts_config(pf, ifr);
default:
return -EOPNOTSUPP;
}
}
/**
* i40e_vlan_stripping_enable - Turn on vlan stripping for the VSI
* @vsi: the vsi being adjusted
......@@ -2150,7 +2171,8 @@ static int i40e_configure_tx_ring(struct i40e_ring *ring)
tx_ctx.base = (ring->dma / 128);
tx_ctx.qlen = ring->count;
tx_ctx.fd_ena = !!(vsi->back->flags & (I40E_FLAG_FDIR_ENABLED |
I40E_FLAG_FDIR_ATR_ENABLED));
I40E_FLAG_FDIR_ATR_ENABLED));
tx_ctx.timesync_ena = !!(vsi->back->flags & I40E_FLAG_PTP);
/* As part of VSI creation/update, FW allocates certain
* Tx arbitration queue sets for each TC enabled for
......@@ -2488,6 +2510,7 @@ static void i40e_enable_misc_int_causes(struct i40e_hw *hw)
I40E_PFINT_ICR0_ENA_GRST_MASK |
I40E_PFINT_ICR0_ENA_PCI_EXCEPTION_MASK |
I40E_PFINT_ICR0_ENA_GPIO_MASK |
I40E_PFINT_ICR0_ENA_TIMESYNC_MASK |
I40E_PFINT_ICR0_ENA_STORM_DETECT_MASK |
I40E_PFINT_ICR0_ENA_HMC_ERR_MASK |
I40E_PFINT_ICR0_ENA_VFLR_MASK |
......@@ -2831,6 +2854,18 @@ static irqreturn_t i40e_intr(int irq, void *data)
dev_info(&pf->pdev->dev, "HMC error interrupt\n");
}
if (icr0 & I40E_PFINT_ICR0_TIMESYNC_MASK) {
u32 prttsyn_stat = rd32(hw, I40E_PRTTSYN_STAT_0);
if (prttsyn_stat & I40E_PRTTSYN_STAT_0_TXTIME_MASK) {
ena_mask &= ~I40E_PFINT_ICR0_ENA_TIMESYNC_MASK;
i40e_ptp_tx_hwtstamp(pf);
prttsyn_stat &= ~I40E_PRTTSYN_STAT_0_TXTIME_MASK;
}
wr32(hw, I40E_PRTTSYN_STAT_0, prttsyn_stat);
}
/* If a critical error is pending we have no choice but to reset the
* device.
* Report and mask out any remaining unexpected interrupts.
......@@ -4304,6 +4339,9 @@ static void i40e_link_event(struct i40e_pf *pf)
if (pf->vf)
i40e_vc_notify_link_state(pf);
if (pf->flags & I40E_FLAG_PTP)
i40e_ptp_set_increment(pf);
}
/**
......@@ -4385,6 +4423,8 @@ static void i40e_watchdog_subtask(struct i40e_pf *pf)
for (i = 0; i < I40E_MAX_VEB; i++)
if (pf->veb[i])
i40e_update_veb_stats(pf->veb[i]);
i40e_ptp_rx_hang(pf->vsi[pf->lan_vsi]);
}
/**
......@@ -6033,6 +6073,7 @@ static const struct net_device_ops i40e_netdev_ops = {
.ndo_validate_addr = eth_validate_addr,
.ndo_set_mac_address = i40e_set_mac,
.ndo_change_mtu = i40e_change_mtu,
.ndo_do_ioctl = i40e_ioctl,
.ndo_tx_timeout = i40e_tx_timeout,
.ndo_vlan_rx_add_vid = i40e_vlan_rx_add_vid,
.ndo_vlan_rx_kill_vid = i40e_vlan_rx_kill_vid,
......@@ -7299,6 +7340,8 @@ static int i40e_setup_pf_switch(struct i40e_pf *pf, bool reinit)
~I40E_PRTDCB_MFLCN_RFCE_MASK);
fc_complete:
i40e_ptp_init(pf);
return ret;
}
......@@ -7803,6 +7846,8 @@ static void i40e_remove(struct pci_dev *pdev)
i40e_dbg_pf_exit(pf);
i40e_ptp_stop(pf);
if (pf->flags & I40E_FLAG_SRIOV_ENABLED) {
i40e_free_vfs(pf);
pf->flags &= ~I40E_FLAG_SRIOV_ENABLED;
......
/*******************************************************************************
*
* Intel Ethernet Controller XL710 Family Linux Driver
* Copyright(c) 2013 - 2014 Intel Corporation.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
* version 2, as published by the Free Software Foundation.
*
* This program is distributed in the hope it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
*
* You should have received a copy of the GNU General Public License along
* with this program. If not, see <http://www.gnu.org/licenses/>.
*
* The full GNU General Public License is included in this distribution in
* the file called "COPYING".
*
* Contact Information:
* e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
* Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
*
******************************************************************************/
#include "i40e.h"
#include <linux/export.h>
#include <linux/ptp_classify.h>
/* The XL710 timesync is very much like Intel's 82599 design when it comes to
* the fundamental clock design. However, the clock operations are much simpler
* in the XL710 because the device supports a full 64 bits of nanoseconds.
* Because the field is so wide, we can forgo the cycle counter and just
* operate with the nanosecond field directly without fear of overflow.
*
* Much like the 82599, the update period is dependent upon the link speed:
* At 40Gb link or no link, the period is 1.6ns.
* At 10Gb link, the period is multiplied by 2. (3.2ns)
* At 1Gb link, the period is multiplied by 20. (32ns)
* 1588 functionality is not supported at 100Mbps.
*/
#define I40E_PTP_40GB_INCVAL 0x0199999999ULL
#define I40E_PTP_10GB_INCVAL 0x0333333333ULL
#define I40E_PTP_1GB_INCVAL 0x2000000000ULL
#define I40E_PRTTSYN_CTL1_TSYNTYPE_V1 (0x1 << \
I40E_PRTTSYN_CTL1_TSYNTYPE_SHIFT)
#define I40E_PRTTSYN_CTL1_TSYNTYPE_V2 (0x2 << \
I40E_PRTTSYN_CTL1_TSYNTYPE_SHIFT)
#define I40E_PTP_TX_TIMEOUT (HZ * 15)
/**
* i40e_ptp_read - Read the PHC time from the device
* @pf: Board private structure
* @ts: timespec structure to hold the current time value
*
* This function reads the PRTTSYN_TIME registers and stores them in a
* timespec. However, since the registers are 64 bits of nanoseconds, we must
* convert the result to a timespec before we can return.
**/
static void i40e_ptp_read(struct i40e_pf *pf, struct timespec *ts)
{
struct i40e_hw *hw = &pf->hw;
u32 hi, lo;
u64 ns;
/* The timer latches on the lowest register read. */
lo = rd32(hw, I40E_PRTTSYN_TIME_L);
hi = rd32(hw, I40E_PRTTSYN_TIME_H);
ns = (((u64)hi) << 32) | lo;
*ts = ns_to_timespec(ns);
}
/**
* i40e_ptp_write - Write the PHC time to the device
* @pf: Board private structure
* @ts: timespec structure that holds the new time value
*
* This function writes the PRTTSYN_TIME registers with the user value. Since
* we receive a timespec from the stack, we must convert that timespec into
* nanoseconds before programming the registers.
**/
static void i40e_ptp_write(struct i40e_pf *pf, const struct timespec *ts)
{
struct i40e_hw *hw = &pf->hw;
u64 ns = timespec_to_ns(ts);
/* The timer will not update until the high register is written, so
* write the low register first.
*/
wr32(hw, I40E_PRTTSYN_TIME_L, ns & 0xFFFFFFFF);
wr32(hw, I40E_PRTTSYN_TIME_H, ns >> 32);
}
/**
* i40e_ptp_convert_to_hwtstamp - Convert device clock to system time
* @hwtstamps: Timestamp structure to update
* @timestamp: Timestamp from the hardware
*
* We need to convert the NIC clock value into a hwtstamp which can be used by
* the upper level timestamping functions. Since the timestamp is simply a 64-
* bit nanosecond value, we can call ns_to_ktime directly to handle this.
**/
static void i40e_ptp_convert_to_hwtstamp(struct skb_shared_hwtstamps *hwtstamps,
u64 timestamp)
{
memset(hwtstamps, 0, sizeof(*hwtstamps));
hwtstamps->hwtstamp = ns_to_ktime(timestamp);
}
/**
* i40e_ptp_adjfreq - Adjust the PHC frequency
* @ptp: The PTP clock structure
* @ppb: Parts per billion adjustment from the base
*
* Adjust the frequency of the PHC by the indicated parts per billion from the
* base frequency.
**/
static int i40e_ptp_adjfreq(struct ptp_clock_info *ptp, s32 ppb)
{
struct i40e_pf *pf = container_of(ptp, struct i40e_pf, ptp_caps);
struct i40e_hw *hw = &pf->hw;
u64 adj, freq, diff;
int neg_adj = 0;
if (ppb < 0) {
neg_adj = 1;
ppb = -ppb;
}
smp_mb(); /* Force any pending update before accessing. */
adj = ACCESS_ONCE(pf->ptp_base_adj);
freq = adj;
freq *= ppb;
diff = div_u64(freq, 1000000000ULL);
if (neg_adj)
adj -= diff;
else
adj += diff;
wr32(hw, I40E_PRTTSYN_INC_L, adj & 0xFFFFFFFF);
wr32(hw, I40E_PRTTSYN_INC_H, adj >> 32);
return 0;
}
/**
* i40e_ptp_adjtime - Adjust the PHC time
* @ptp: The PTP clock structure
* @delta: Offset in nanoseconds to adjust the PHC time by
*
* Adjust the frequency of the PHC by the indicated parts per billion from the
* base frequency.
**/
static int i40e_ptp_adjtime(struct ptp_clock_info *ptp, s64 delta)
{
struct i40e_pf *pf = container_of(ptp, struct i40e_pf, ptp_caps);
struct timespec now, then = ns_to_timespec(delta);
unsigned long flags;
spin_lock_irqsave(&pf->tmreg_lock, flags);
i40e_ptp_read(pf, &now);
now = timespec_add(now, then);
i40e_ptp_write(pf, (const struct timespec *)&now);
spin_unlock_irqrestore(&pf->tmreg_lock, flags);
return 0;
}
/**
* i40e_ptp_gettime - Get the time of the PHC
* @ptp: The PTP clock structure
* @ts: timespec structure to hold the current time value
*
* Read the device clock and return the correct value on ns, after converting it
* into a timespec struct.
**/
static int i40e_ptp_gettime(struct ptp_clock_info *ptp, struct timespec *ts)
{
struct i40e_pf *pf = container_of(ptp, struct i40e_pf, ptp_caps);
unsigned long flags;
spin_lock_irqsave(&pf->tmreg_lock, flags);
i40e_ptp_read(pf, ts);
spin_unlock_irqrestore(&pf->tmreg_lock, flags);
return 0;
}
/**
* i40e_ptp_settime - Set the time of the PHC
* @ptp: The PTP clock structure
* @ts: timespec structure that holds the new time value
*
* Set the device clock to the user input value. The conversion from timespec
* to ns happens in the write function.
**/
static int i40e_ptp_settime(struct ptp_clock_info *ptp,
const struct timespec *ts)
{
struct i40e_pf *pf = container_of(ptp, struct i40e_pf, ptp_caps);
unsigned long flags;
spin_lock_irqsave(&pf->tmreg_lock, flags);
i40e_ptp_write(pf, ts);
spin_unlock_irqrestore(&pf->tmreg_lock, flags);
return 0;
}
/**
* i40e_ptp_tx_work
* @work: pointer to work struct
*
* This work function polls the PRTTSYN_STAT_0.TXTIME bit to determine when a
* Tx timestamp event has occurred, in order to pass the Tx timestamp value up
* the stack in the skb.
*/
static void i40e_ptp_tx_work(struct work_struct *work)
{
struct i40e_pf *pf = container_of(work, struct i40e_pf,
ptp_tx_work);
struct i40e_hw *hw = &pf->hw;
u32 prttsyn_stat_0;
if (!pf->ptp_tx_skb)
return;
if (time_is_before_jiffies(pf->ptp_tx_start +
I40E_PTP_TX_TIMEOUT)) {
dev_kfree_skb_any(pf->ptp_tx_skb);
pf->ptp_tx_skb = NULL;
pf->tx_hwtstamp_timeouts++;
dev_warn(&pf->pdev->dev, "clearing Tx timestamp hang");
return;
}
prttsyn_stat_0 = rd32(hw, I40E_PRTTSYN_STAT_0);
if (prttsyn_stat_0 & I40E_PRTTSYN_STAT_0_TXTIME_MASK)
i40e_ptp_tx_hwtstamp(pf);
else
schedule_work(&pf->ptp_tx_work);
}
/**
* i40e_ptp_enable - Enable/disable ancillary features of the PHC subsystem
* @ptp: The PTP clock structure
* @rq: The requested feature to change
* @on: Enable/disable flag
*
* The XL710 does not support any of the ancillary features of the PHC
* subsystem, so this function may just return.
**/
static int i40e_ptp_enable(struct ptp_clock_info *ptp,
struct ptp_clock_request *rq, int on)
{
return -EOPNOTSUPP;
}
/**
* i40e_ptp_rx_hang - Detect error case when Rx timestamp registers are hung
* @vsi: The VSI with the rings relevant to 1588
*
* This watchdog task is scheduled to detect error case where hardware has
* dropped an Rx packet that was timestamped when the ring is full. The
* particular error is rare but leaves the device in a state unable to timestamp
* any future packets.
**/
void i40e_ptp_rx_hang(struct i40e_vsi *vsi)
{
struct i40e_pf *pf = vsi->back;
struct i40e_hw *hw = &pf->hw;
struct i40e_ring *rx_ring;
unsigned long rx_event;
u32 prttsyn_stat;
int n;
if (pf->flags & I40E_FLAG_PTP)
return;
prttsyn_stat = rd32(hw, I40E_PRTTSYN_STAT_1);
/* Unless all four receive timestamp registers are latched, we are not
* concerned about a possible PTP Rx hang, so just update the timeout
* counter and exit.
*/
if (!(prttsyn_stat & ((I40E_PRTTSYN_STAT_1_RXT0_MASK <<
I40E_PRTTSYN_STAT_1_RXT0_SHIFT) |
(I40E_PRTTSYN_STAT_1_RXT1_MASK <<
I40E_PRTTSYN_STAT_1_RXT1_SHIFT) |
(I40E_PRTTSYN_STAT_1_RXT2_MASK <<
I40E_PRTTSYN_STAT_1_RXT2_SHIFT) |
(I40E_PRTTSYN_STAT_1_RXT3_MASK <<
I40E_PRTTSYN_STAT_1_RXT3_SHIFT)))) {
pf->last_rx_ptp_check = jiffies;
return;
}
/* Determine the most recent watchdog or rx_timestamp event. */
rx_event = pf->last_rx_ptp_check;
for (n = 0; n < vsi->num_queue_pairs; n++) {
rx_ring = vsi->rx_rings[n];
if (time_after(rx_ring->last_rx_timestamp, rx_event))
rx_event = rx_ring->last_rx_timestamp;
}
/* Only need to read the high RXSTMP register to clear the lock */
if (time_is_before_jiffies(rx_event + 5 * HZ)) {
rd32(hw, I40E_PRTTSYN_RXTIME_H(0));
rd32(hw, I40E_PRTTSYN_RXTIME_H(1));
rd32(hw, I40E_PRTTSYN_RXTIME_H(2));
rd32(hw, I40E_PRTTSYN_RXTIME_H(3));
pf->last_rx_ptp_check = jiffies;
pf->rx_hwtstamp_cleared++;
dev_warn(&vsi->back->pdev->dev,
"%s: clearing Rx timestamp hang",
__func__);
}
}
/**
* i40e_ptp_tx_hwtstamp - Utility function which returns the Tx timestamp
* @pf: Board private structure
*
* Read the value of the Tx timestamp from the registers, convert it into a
* value consumable by the stack, and store that result into the shhwtstamps
* struct before returning it up the stack.
**/
void i40e_ptp_tx_hwtstamp(struct i40e_pf *pf)
{
struct skb_shared_hwtstamps shhwtstamps;
struct i40e_hw *hw = &pf->hw;
u32 hi, lo;
u64 ns;
lo = rd32(hw, I40E_PRTTSYN_TXTIME_L);
hi = rd32(hw, I40E_PRTTSYN_TXTIME_H);
ns = (((u64)hi) << 32) | lo;
i40e_ptp_convert_to_hwtstamp(&shhwtstamps, ns);
skb_tstamp_tx(pf->ptp_tx_skb, &shhwtstamps);
dev_kfree_skb_any(pf->ptp_tx_skb);
pf->ptp_tx_skb = NULL;
}
/**
* i40e_ptp_rx_hwtstamp - Utility function which checks for an Rx timestamp
* @pf: Board private structure
* @skb: Particular skb to send timestamp with
* @index: Index into the receive timestamp registers for the timestamp
*
* The XL710 receives a notification in the receive descriptor with an offset
* into the set of RXTIME registers where the timestamp is for that skb. This
* function goes and fetches the receive timestamp from that offset, if a valid
* one exists. The RXTIME registers are in ns, so we must convert the result
* first.
**/
void i40e_ptp_rx_hwtstamp(struct i40e_pf *pf, struct sk_buff *skb, u8 index)
{
u32 prttsyn_stat, hi, lo;
struct i40e_hw *hw;
u64 ns;
/* Since we cannot turn off the Rx timestamp logic if the device is
* doing Tx timestamping, check if Rx timestamping is configured.
*/
if (!pf->ptp_rx)
return;
hw = &pf->hw;
prttsyn_stat = rd32(hw, I40E_PRTTSYN_STAT_1);
if (!(prttsyn_stat & (1 << index)))
return;
lo = rd32(hw, I40E_PRTTSYN_RXTIME_L(index));
hi = rd32(hw, I40E_PRTTSYN_RXTIME_H(index));
ns = (((u64)hi) << 32) | lo;
i40e_ptp_convert_to_hwtstamp(skb_hwtstamps(skb), ns);
}
/**
* i40e_ptp_set_increment - Utility function to update clock increment rate
* @pf: Board private structure
*
* During a link change, the DMA frequency that drives the 1588 logic will
* change. In order to keep the PRTTSYN_TIME registers in units of nanoseconds,
* we must update the increment value per clock tick.
**/
void i40e_ptp_set_increment(struct i40e_pf *pf)
{
struct i40e_link_status *hw_link_info;
struct i40e_hw *hw = &pf->hw;
u64 incval;
hw_link_info = &hw->phy.link_info;
i40e_aq_get_link_info(&pf->hw, true, NULL, NULL);
switch (hw_link_info->link_speed) {
case I40E_LINK_SPEED_10GB:
incval = I40E_PTP_10GB_INCVAL;
break;
case I40E_LINK_SPEED_1GB:
incval = I40E_PTP_1GB_INCVAL;
break;
case I40E_LINK_SPEED_100MB:
dev_warn(&pf->pdev->dev,
"%s: 1588 functionality is not supported at 100 Mbps. Stopping the PHC.\n",
__func__);
incval = 0;
break;
case I40E_LINK_SPEED_40GB:
default:
incval = I40E_PTP_40GB_INCVAL;
break;
}
/* Write the new increment value into the increment register. The
* hardware will not update the clock until both registers have been
* written.
*/
wr32(hw, I40E_PRTTSYN_INC_L, incval & 0xFFFFFFFF);
wr32(hw, I40E_PRTTSYN_INC_H, incval >> 32);
/* Update the base adjustement value. */
ACCESS_ONCE(pf->ptp_base_adj) = incval;
smp_mb(); /* Force the above update. */
}
/**
* i40e_ptp_get_ts_config - ioctl interface to read the HW timestamping
* @pf: Board private structure
* @ifreq: ioctl data
*
* Obtain the current hardware timestamping settigs as requested. To do this,
* keep a shadow copy of the timestamp settings rather than attempting to
* deconstruct it from the registers.
**/
int i40e_ptp_get_ts_config(struct i40e_pf *pf, struct ifreq *ifr)
{
struct hwtstamp_config *config = &pf->tstamp_config;
return copy_to_user(ifr->ifr_data, config, sizeof(*config)) ?
-EFAULT : 0;
}
/**
* i40e_ptp_set_ts_config - ioctl interface to control the HW timestamping
* @pf: Board private structure
* @ifreq: ioctl data
*
* Respond to the user filter requests and make the appropriate hardware
* changes here. The XL710 cannot support splitting of the Tx/Rx timestamping
* logic, so keep track in software of whether to indicate these timestamps
* or not.
*
* It is permissible to "upgrade" the user request to a broader filter, as long
* as the user receives the timestamps they care about and the user is notified
* the filter has been broadened.
**/
int i40e_ptp_set_ts_config(struct i40e_pf *pf, struct ifreq *ifr)
{
struct i40e_hw *hw = &pf->hw;
struct hwtstamp_config *config = &pf->tstamp_config;
u32 pf_id, tsyntype, regval;
if (copy_from_user(config, ifr->ifr_data, sizeof(*config)))
return -EFAULT;
/* Reserved for future extensions. */
if (config->flags)
return -EINVAL;
/* Confirm that 1588 is supported on this PF. */
pf_id = (rd32(hw, I40E_PRTTSYN_CTL0) & I40E_PRTTSYN_CTL0_PF_ID_MASK) >>
I40E_PRTTSYN_CTL0_PF_ID_SHIFT;
if (hw->pf_id != pf_id)
return -EINVAL;
switch (config->tx_type) {
case HWTSTAMP_TX_OFF:
pf->ptp_tx = false;
break;
case HWTSTAMP_TX_ON:
pf->ptp_tx = true;
break;
default:
return -ERANGE;
}
switch (config->rx_filter) {
case HWTSTAMP_FILTER_NONE:
pf->ptp_rx = false;
tsyntype = 0;
break;
case HWTSTAMP_FILTER_PTP_V1_L4_SYNC:
case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ:
case HWTSTAMP_FILTER_PTP_V1_L4_EVENT:
pf->ptp_rx = true;
tsyntype = I40E_PRTTSYN_CTL1_V1MESSTYPE0_MASK |
I40E_PRTTSYN_CTL1_TSYNTYPE_V1 |
I40E_PRTTSYN_CTL1_UDP_ENA_MASK;
config->rx_filter = HWTSTAMP_FILTER_PTP_V1_L4_EVENT;
break;
case HWTSTAMP_FILTER_PTP_V2_EVENT:
case HWTSTAMP_FILTER_PTP_V2_L2_EVENT:
case HWTSTAMP_FILTER_PTP_V2_L4_EVENT:
case HWTSTAMP_FILTER_PTP_V2_SYNC:
case HWTSTAMP_FILTER_PTP_V2_L2_SYNC:
case HWTSTAMP_FILTER_PTP_V2_L4_SYNC:
case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ:
case HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ:
case HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ:
pf->ptp_rx = true;
tsyntype = I40E_PRTTSYN_CTL1_V2MESSTYPE0_MASK |
I40E_PRTTSYN_CTL1_TSYNTYPE_V2 |
I40E_PRTTSYN_CTL1_UDP_ENA_MASK;
config->rx_filter = HWTSTAMP_FILTER_PTP_V2_EVENT;
break;
case HWTSTAMP_FILTER_ALL:
default:
return -ERANGE;
}
/* Clear out all 1588-related registers to clear and unlatch them. */
rd32(hw, I40E_PRTTSYN_STAT_0);
rd32(hw, I40E_PRTTSYN_TXTIME_H);
rd32(hw, I40E_PRTTSYN_RXTIME_H(0));
rd32(hw, I40E_PRTTSYN_RXTIME_H(1));
rd32(hw, I40E_PRTTSYN_RXTIME_H(2));
rd32(hw, I40E_PRTTSYN_RXTIME_H(3));
/* Enable/disable the Tx timestamp interrupt based on user input. */
regval = rd32(hw, I40E_PRTTSYN_CTL0);
if (pf->ptp_tx)
regval |= I40E_PRTTSYN_CTL0_TXTIME_INT_ENA_MASK;
else
regval &= ~I40E_PRTTSYN_CTL0_TXTIME_INT_ENA_MASK;
wr32(hw, I40E_PRTTSYN_CTL0, regval);
regval = rd32(hw, I40E_PFINT_ICR0_ENA);
if (pf->ptp_tx)
regval |= I40E_PFINT_ICR0_ENA_TIMESYNC_MASK;
else
regval &= ~I40E_PFINT_ICR0_ENA_TIMESYNC_MASK;
wr32(hw, I40E_PFINT_ICR0_ENA, regval);
/* There is no simple on/off switch for Rx. To "disable" Rx support,
* ignore any received timestamps, rather than turn off the clock.
*/
if (pf->ptp_rx) {
regval = rd32(hw, I40E_PRTTSYN_CTL1);
/* clear everything but the enable bit */
regval &= I40E_PRTTSYN_CTL1_TSYNENA_MASK;
/* now enable bits for desired Rx timestamps */
regval |= tsyntype;
wr32(hw, I40E_PRTTSYN_CTL1, regval);
}
return copy_to_user(ifr->ifr_data, config, sizeof(*config)) ?
-EFAULT : 0;
}
/**
* i40e_ptp_init - Initialize the 1588 support and register the PHC
* @pf: Board private structure
*
* This function registers the device clock as a PHC. If it is successful, it
* starts the clock in the hardware.
**/
void i40e_ptp_init(struct i40e_pf *pf)
{
struct i40e_hw *hw = &pf->hw;
struct net_device *netdev = pf->vsi[pf->lan_vsi]->netdev;
strncpy(pf->ptp_caps.name, "i40e", sizeof(pf->ptp_caps.name));
pf->ptp_caps.owner = THIS_MODULE;
pf->ptp_caps.max_adj = 999999999;
pf->ptp_caps.n_ext_ts = 0;
pf->ptp_caps.pps = 0;
pf->ptp_caps.adjfreq = i40e_ptp_adjfreq;
pf->ptp_caps.adjtime = i40e_ptp_adjtime;
pf->ptp_caps.gettime = i40e_ptp_gettime;
pf->ptp_caps.settime = i40e_ptp_settime;
pf->ptp_caps.enable = i40e_ptp_enable;
/* Attempt to register the clock before enabling the hardware. */
pf->ptp_clock = ptp_clock_register(&pf->ptp_caps, &pf->pdev->dev);
if (IS_ERR(pf->ptp_clock)) {
pf->ptp_clock = NULL;
dev_err(&pf->pdev->dev, "%s: ptp_clock_register failed\n",
__func__);
} else {
struct timespec ts;
u32 regval;
spin_lock_init(&pf->tmreg_lock);
INIT_WORK(&pf->ptp_tx_work, i40e_ptp_tx_work);
dev_info(&pf->pdev->dev, "%s: added PHC on %s\n", __func__,
netdev->name);
pf->flags |= I40E_FLAG_PTP;
/* Ensure the clocks are running. */
regval = rd32(hw, I40E_PRTTSYN_CTL0);
regval |= I40E_PRTTSYN_CTL0_TSYNENA_MASK;
wr32(hw, I40E_PRTTSYN_CTL0, regval);
regval = rd32(hw, I40E_PRTTSYN_CTL1);
regval |= I40E_PRTTSYN_CTL1_TSYNENA_MASK;
wr32(hw, I40E_PRTTSYN_CTL1, regval);
/* Set the increment value per clock tick. */
i40e_ptp_set_increment(pf);
/* reset the tstamp_config */
memset(&pf->tstamp_config, 0, sizeof(pf->tstamp_config));
/* Set the clock value. */
ts = ktime_to_timespec(ktime_get_real());
i40e_ptp_settime(&pf->ptp_caps, &ts);
}
}
/**
* i40e_ptp_stop - Disable the driver/hardware support and unregister the PHC
* @pf: Board private structure
*
* This function handles the cleanup work required from the initialization by
* clearing out the important information and unregistering the PHC.
**/
void i40e_ptp_stop(struct i40e_pf *pf)
{
pf->flags &= ~I40E_FLAG_PTP;
pf->ptp_tx = false;
pf->ptp_rx = false;
cancel_work_sync(&pf->ptp_tx_work);
if (pf->ptp_tx_skb) {
dev_kfree_skb_any(pf->ptp_tx_skb);
pf->ptp_tx_skb = NULL;
}
if (pf->ptp_clock) {
ptp_clock_unregister(pf->ptp_clock);
pf->ptp_clock = NULL;
dev_info(&pf->pdev->dev, "%s: removed PHC on %s\n", __func__,
pf->vsi[pf->lan_vsi]->netdev->name);
}
}
......@@ -1088,6 +1088,13 @@ static int i40e_clean_rx_irq(struct i40e_ring *rx_ring, int budget)
}
skb->rxhash = i40e_rx_hash(rx_ring, rx_desc);
if (unlikely(rx_status & I40E_RXD_QW1_STATUS_TSYNVALID_MASK)) {
i40e_ptp_rx_hwtstamp(vsi->back, skb, (rx_status &
I40E_RXD_QW1_STATUS_TSYNINDX_MASK) >>
I40E_RXD_QW1_STATUS_TSYNINDX_SHIFT);
rx_ring->last_rx_timestamp = jiffies;
}
/* probably a little skewed due to removing CRC */
total_rx_bytes += skb->len;
total_rx_packets++;
......@@ -1425,6 +1432,46 @@ static int i40e_tso(struct i40e_ring *tx_ring, struct sk_buff *skb,
return 1;
}
/**
* i40e_tsyn - set up the tsyn context descriptor
* @tx_ring: ptr to the ring to send
* @skb: ptr to the skb we're sending
* @tx_flags: the collected send information
*
* Returns 0 if no Tx timestamp can happen and 1 if the timestamp will happen
**/
static int i40e_tsyn(struct i40e_ring *tx_ring, struct sk_buff *skb,
u32 tx_flags, u64 *cd_type_cmd_tso_mss)
{
struct i40e_pf *pf;
if (likely(!(skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP)))
return 0;
/* Tx timestamps cannot be sampled when doing TSO */
if (tx_flags & I40E_TX_FLAGS_TSO)
return 0;
/* only timestamp the outbound packet if the user has requested it and
* we are not already transmitting a packet to be timestamped
*/
pf = i40e_netdev_to_pf(tx_ring->netdev);
if (pf->ptp_tx && !pf->ptp_tx_skb) {
skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS;
pf->ptp_tx_skb = skb_get(skb);
} else {
return 0;
}
*cd_type_cmd_tso_mss |= (u64)I40E_TX_CTX_DESC_TSYN <<
I40E_TXD_CTX_QW1_CMD_SHIFT;
pf->ptp_tx_start = jiffies;
schedule_work(&pf->ptp_tx_work);
return 1;
}
/**
* i40e_tx_enable_csum - Enable Tx checksum offloads
* @skb: send buffer
......@@ -1801,6 +1848,7 @@ static netdev_tx_t i40e_xmit_frame_ring(struct sk_buff *skb,
__be16 protocol;
u32 td_cmd = 0;
u8 hdr_len = 0;
int tsyn;
int tso;
if (0 == i40e_xmit_descriptor_count(skb, tx_ring))
return NETDEV_TX_BUSY;
......@@ -1831,6 +1879,11 @@ static netdev_tx_t i40e_xmit_frame_ring(struct sk_buff *skb,
skb_tx_timestamp(skb);
tsyn = i40e_tsyn(tx_ring, skb, tx_flags, &cd_type_cmd_tso_mss);
if (tsyn)
tx_flags |= I40E_TX_FLAGS_TSYN;
/* always enable CRC insertion offload */
td_cmd |= I40E_TX_DESC_CMD_ICRC;
......
......@@ -136,6 +136,7 @@ enum i40e_dyn_idx_t {
#define I40E_TX_FLAGS_IPV6 (u32)(1 << 5)
#define I40E_TX_FLAGS_FCCRC (u32)(1 << 6)
#define I40E_TX_FLAGS_FSO (u32)(1 << 7)
#define I40E_TX_FLAGS_TSYN (u32)(1 << 8)
#define I40E_TX_FLAGS_VLAN_MASK 0xffff0000
#define I40E_TX_FLAGS_VLAN_PRIO_MASK 0xe0000000
#define I40E_TX_FLAGS_VLAN_PRIO_SHIFT 29
......@@ -248,6 +249,8 @@ struct i40e_ring {
u8 atr_sample_rate;
u8 atr_count;
unsigned long last_rx_timestamp;
bool ring_active; /* is ring online or not */
/* stats structs */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment