net: Fix misspellings of "configure" and "configuration"

Fix various misspellings of "configuration" and "configure".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/mellanox/mlx5/core/en/port_buffer.c

@@ -175,7 +175,7 @@ static int update_xoff_threshold(struct mlx5e_port_buffer *port_buffer,
  *	@port_buffer: <output> port receive buffer configuration
  *	@change: <output>
  *
- *	Update buffer configuration based on pfc configuraiton and
+ *	Update buffer configuration based on pfc configuration and
  *	priority to buffer mapping.
  *	Buffer's lossy bit is changed to:
  *		lossless if there is at least one PFC enabled priority

drivers/net/ethernet/qlogic/qed/qed_int.h

@@ -37,14 +37,14 @@
 #include <linux/slab.h>
 #include "qed.h"
 
-/* Fields of IGU PF CONFIGRATION REGISTER */
+/* Fields of IGU PF CONFIGURATION REGISTER */
 #define IGU_PF_CONF_FUNC_EN       (0x1 << 0)    /* function enable        */
 #define IGU_PF_CONF_MSI_MSIX_EN   (0x1 << 1)    /* MSI/MSIX enable        */
 #define IGU_PF_CONF_INT_LINE_EN   (0x1 << 2)    /* INT enable             */
 #define IGU_PF_CONF_ATTN_BIT_EN   (0x1 << 3)    /* attention enable       */
 #define IGU_PF_CONF_SINGLE_ISR_EN (0x1 << 4)    /* single ISR mode enable */
 #define IGU_PF_CONF_SIMD_MODE     (0x1 << 5)    /* simd all ones mode     */
-/* Fields of IGU VF CONFIGRATION REGISTER */
+/* Fields of IGU VF CONFIGURATION REGISTER */
 #define IGU_VF_CONF_FUNC_EN        (0x1 << 0)	/* function enable        */
 #define IGU_VF_CONF_MSI_MSIX_EN    (0x1 << 1)	/* MSI/MSIX enable        */
 #define IGU_VF_CONF_SINGLE_ISR_EN  (0x1 << 4)	/* single ISR mode enable */

drivers/net/ethernet/qlogic/qed/qed_sriov.h

@@ -305,7 +305,7 @@ void qed_iov_bulletin_set_udp_ports(struct qed_hwfn *p_hwfn,
 
 /**
  * @brief Read sriov related information and allocated resources
- *  reads from configuraiton space, shmem, etc.
+ *  reads from configuration space, shmem, etc.
  *
  * @param p_hwfn
  *

drivers/net/ethernet/qlogic/qede/qede_filter.c

@@ -1298,7 +1298,7 @@ void qede_config_rx_mode(struct net_device *ndev)
 	rx_mode.type = QED_FILTER_TYPE_RX_MODE;
 
 	/* Remove all previous unicast secondary macs and multicast macs
-	 * (configrue / leave the primary mac)
+	 * (configure / leave the primary mac)
 	 */
 	rc = qede_set_ucast_rx_mac(edev, QED_FILTER_XCAST_TYPE_REPLACE,
 				   edev->ndev->dev_addr);

drivers/net/wireless/ath/ath9k/ar9003_hw.c

@@ -1037,7 +1037,7 @@ static void ar9003_hw_configpcipowersave(struct ath_hw *ah,
 	}
 
 	/*
-	 * Configire PCIE after Ini init. SERDES values now come from ini file
+	 * Configure PCIE after Ini init. SERDES values now come from ini file
 	 * This enables PCIe low power mode.
 	 */
 	array = power_off ? &ah->iniPcieSerdes :

drivers/net/wireless/intel/iwlwifi/iwl-fh.h

@@ -148,7 +148,7 @@ static inline unsigned int FH_MEM_CBBC_QUEUE(struct iwl_trans *trans,
  *
  * Bits 3:0:
  * Define the maximum number of pending read requests.
- * Maximum configration value allowed is 0xC
+ * Maximum configuration value allowed is 0xC
  * Bits 9:8:
  * Define the maximum transfer size. (64 / 128 / 256)
  * Bit 10:

drivers/net/wireless/ti/wlcore/spi.c

@@ -186,7 +186,7 @@ static void wl12xx_spi_init(struct device *child)
 
 	spi_sync(to_spi_device(glue->dev), &m);
 
-	/* Restore chip select configration to normal */
+	/* Restore chip select configuration to normal */
 	spi->mode ^= SPI_CS_HIGH;
 	kfree(cmd);
 }

include/uapi/linux/dcbnl.h

@@ -286,7 +286,7 @@ struct dcbmsg {
  * @DCB_CMD_GNUMTCS: get the number of traffic classes currently supported
  * @DCB_CMD_SNUMTCS: set the number of traffic classes
  * @DCB_CMD_GBCN: set backward congestion notification configuration
- * @DCB_CMD_SBCN: get backward congestion notification configration.
+ * @DCB_CMD_SBCN: get backward congestion notification configuration.
  * @DCB_CMD_GAPP: get application protocol configuration
  * @DCB_CMD_SAPP: set application protocol configuration
  * @DCB_CMD_IEEE_SET: set IEEE 802.1Qaz configuration