Commit c502224e authored by Somnath Kotur's avatar Somnath Kotur Committed by David S. Miller

be2net: Fix to reset transparent vlan tagging

For disabling transparent tagging issue SET_HSW_CONFIG with pvid_valid=1
and pvid=0xFFFF and not with the default pvid as this case would fail in Lancer.
Hence removing the get_hsw_config call from be_vf_setup() as it's
only use of getting default pvid is no longer needed.

Also do proper housekeeping only if the FW command succeeds.
Signed-off-by: default avatarKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: default avatarSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent e842b068
......@@ -350,11 +350,13 @@ struct be_drv_stats {
u32 roce_drops_crc;
};
/* A vlan-id of 0xFFFF must be used to clear transparent vlan-tagging */
#define BE_RESET_VLAN_TAG_ID 0xFFFF
struct be_vf_cfg {
unsigned char mac_addr[ETH_ALEN];
int if_handle;
int pmac_id;
u16 def_vid;
u16 vlan_tag;
u32 tx_rate;
};
......
......@@ -1287,22 +1287,18 @@ static int be_set_vf_vlan(struct net_device *netdev,
if (vlan || qos) {
vlan |= qos << VLAN_PRIO_SHIFT;
if (vf_cfg->vlan_tag != vlan) {
/* If this is new value, program it. Else skip. */
vf_cfg->vlan_tag = vlan;
if (vf_cfg->vlan_tag != vlan)
status = be_cmd_set_hsw_config(adapter, vlan, vf + 1,
vf_cfg->if_handle, 0);
}
} else {
/* Reset Transparent Vlan Tagging. */
vf_cfg->vlan_tag = 0;
vlan = vf_cfg->def_vid;
status = be_cmd_set_hsw_config(adapter, vlan, vf + 1,
vf_cfg->if_handle, 0);
status = be_cmd_set_hsw_config(adapter, BE_RESET_VLAN_TAG_ID,
vf + 1, vf_cfg->if_handle, 0);
}
if (status)
if (!status)
vf_cfg->vlan_tag = vlan;
else
dev_info(&adapter->pdev->dev,
"VLAN %d config on VF %d failed\n", vlan, vf);
return status;
......@@ -3013,11 +3009,11 @@ static int be_vf_setup_init(struct be_adapter *adapter)
static int be_vf_setup(struct be_adapter *adapter)
{
struct device *dev = &adapter->pdev->dev;
struct be_vf_cfg *vf_cfg;
u16 def_vlan, lnk_speed;
int status, old_vfs, vf;
struct device *dev = &adapter->pdev->dev;
u32 privileges;
u16 lnk_speed;
old_vfs = pci_num_vf(adapter->pdev);
if (old_vfs) {
......@@ -3084,12 +3080,6 @@ static int be_vf_setup(struct be_adapter *adapter)
if (!status)
vf_cfg->tx_rate = lnk_speed;
status = be_cmd_get_hsw_config(adapter, &def_vlan,
vf + 1, vf_cfg->if_handle, NULL);
if (status)
goto err;
vf_cfg->def_vid = def_vlan;
if (!old_vfs)
be_cmd_enable_vf(adapter, vf + 1);
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment