Merge remote-tracking branches 'spi/topic/ti-qspi', 'spi/topic/xcomm' and...

Merge remote-tracking branches 'spi/topic/ti-qspi', 'spi/topic/xcomm' and 'spi/topic/xlp' into spi-next

Documentation/devicetree/bindings/spi/spi-xlp.txt

+SPI Master controller for Netlogic XLP MIPS64 SOCs
+==================================================
+
+Currently this SPI controller driver is supported for the following
+Netlogic XLP SoCs:
+	XLP832, XLP316, XLP208, XLP980, XLP532
+
+Required properties:
+- compatible		: Should be "netlogic,xlp832-spi".
+- #address-cells	: Number of cells required to define a chip select address
+			  on the SPI bus.
+- #size-cells		: Should be zero.
+- reg			: Should contain register location and length.
+- clocks		: Phandle of the spi clock
+- interrupts		: Interrupt number used by this controller.
+- interrupt-parent	: Phandle of the parent interrupt controller.
+
+SPI slave nodes must be children of the SPI master node and can contain
+properties described in Documentation/devicetree/bindings/spi/spi-bus.txt.
+
+Example:
+
+	spi: xlp_spi@3a100 {
+		compatible = "netlogic,xlp832-spi";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0 0x3a100 0x100>;
+		clocks = <&spi_clk>;
+		interrupts = <34>;
+		interrupt-parent = <&pic>;
+
+		spi_nor@1 {
+			compatible = "spansion,s25sl12801";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <1>;	/* Chip Select */
+			spi-max-frequency = <40000000>;
+		};
+};

drivers/spi/Kconfig

@@ -607,6 +607,17 @@ config SPI_XILINX
 
 	  Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
 
+config SPI_XLP
+	tristate "Netlogic XLP SPI controller driver"
+	depends on CPU_XLP || COMPILE_TEST
+	help
+	  Enable support for the SPI controller on the Netlogic XLP SoCs.
+	  Currently supported XLP variants are XLP8XX, XLP3XX, XLP2XX, XLP9XX
+	  and XLP5XX.
+
+	  If you have a Netlogic XLP platform say Y here.
+	  If unsure, say N.
+
 config SPI_XTENSA_XTFPGA
 	tristate "Xtensa SPI controller for xtfpga"
 	depends on (XTENSA && XTENSA_PLATFORM_XTFPGA) || COMPILE_TEST

drivers/spi/Makefile

@@ -89,5 +89,6 @@ obj-$(CONFIG_SPI_TOPCLIFF_PCH)		+= spi-topcliff-pch.o
 obj-$(CONFIG_SPI_TXX9)			+= spi-txx9.o
 obj-$(CONFIG_SPI_XCOMM)		+= spi-xcomm.o
 obj-$(CONFIG_SPI_XILINX)		+= spi-xilinx.o
+obj-$(CONFIG_SPI_XLP)			+= spi-xlp.o
 obj-$(CONFIG_SPI_XTENSA_XTFPGA)		+= spi-xtensa-xtfpga.o
 obj-$(CONFIG_SPI_ZYNQMP_GQSPI)		+= spi-zynqmp-gqspi.o

drivers/spi/spi-ti-qspi.c

@@ -99,6 +99,8 @@ struct ti_qspi {
 #define QSPI_INVAL			(4 << 16)
 #define QSPI_WC_CMD_INT_EN			(1 << 14)
 #define QSPI_FLEN(n)			((n - 1) << 0)
+#define QSPI_WLEN_MAX_BITS		128
+#define QSPI_WLEN_MAX_BYTES		16
 
 /* STATUS REGISTER */
 #define BUSY				0x01
@@ -217,14 +219,16 @@ static inline u32 qspi_is_busy(struct ti_qspi *qspi)
 
 static int qspi_write_msg(struct ti_qspi *qspi, struct spi_transfer *t)
 {
-	int wlen, count;
+	int wlen, count, xfer_len;
 	unsigned int cmd;
 	const u8 *txbuf;
+	u32 data;
 
 	txbuf = t->tx_buf;
 	cmd = qspi->cmd | QSPI_WR_SNGL;
 	count = t->len;
 	wlen = t->bits_per_word >> 3;	/* in bytes */
+	xfer_len = wlen;
 
 	while (count) {
 		if (qspi_is_busy(qspi))
@@ -234,7 +238,29 @@ static int qspi_write_msg(struct ti_qspi *qspi, struct spi_transfer *t)
 		case 1:
 			dev_dbg(qspi->dev, "tx cmd %08x dc %08x data %02x\n",
 					cmd, qspi->dc, *txbuf);
+			if (count >= QSPI_WLEN_MAX_BYTES) {
+				u32 *txp = (u32 *)txbuf;
+
+				data = cpu_to_be32(*txp++);
+				writel(data, qspi->base +
+				       QSPI_SPI_DATA_REG_3);
+				data = cpu_to_be32(*txp++);
+				writel(data, qspi->base +
+				       QSPI_SPI_DATA_REG_2);
+				data = cpu_to_be32(*txp++);
+				writel(data, qspi->base +
+				       QSPI_SPI_DATA_REG_1);
+				data = cpu_to_be32(*txp++);
+				writel(data, qspi->base +
+				       QSPI_SPI_DATA_REG);
+				xfer_len = QSPI_WLEN_MAX_BYTES;
+				cmd |= QSPI_WLEN(QSPI_WLEN_MAX_BITS);
+			} else {
 				writeb(*txbuf, qspi->base + QSPI_SPI_DATA_REG);
+				cmd = qspi->cmd | QSPI_WR_SNGL;
+				xfer_len = wlen;
+				cmd |= QSPI_WLEN(wlen);
+			}
 			break;
 		case 2:
 			dev_dbg(qspi->dev, "tx cmd %08x dc %08x data %04x\n",
@@ -254,8 +280,8 @@ static int qspi_write_msg(struct ti_qspi *qspi, struct spi_transfer *t)
 			dev_err(qspi->dev, "write timed out\n");
 			return -ETIMEDOUT;
 		}
-		txbuf += wlen;
-		count -= wlen;
+		txbuf += xfer_len;
+		count -= xfer_len;
 	}
 
 	return 0;

drivers/spi/spi-xcomm.c

@@ -237,11 +237,11 @@ static const struct i2c_device_id spi_xcomm_ids[] = {
 	{ "spi-xcomm" },
 	{ },
 };
+MODULE_DEVICE_TABLE(i2c, spi_xcomm_ids);
 
 static struct i2c_driver spi_xcomm_driver = {
 	.driver = {
 		.name	= "spi-xcomm",
-		.owner	= THIS_MODULE,
 	},
 	.id_table	= spi_xcomm_ids,
 	.probe		= spi_xcomm_probe,