Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM 64-bit DT updates from Arnd Bergmann:
 "ARM64 DT updates are fairly small this time, only two new SoCs and a
  handful of new machines get added, all of them similar to other
  hardware we already support.

  New SoC:

   - HiSilicon Kirin960/Hi3660 and HiKey960 development board

   - NXP LS1012a with three reference boards:
        http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-layerscape-arm-processors/qoriq-layerscape-1012a-low-power-communication-processor:LS1012A

  New development board:

   - Banana Pi M64, based on Allwinner A64:
        http://www.banana-pi.org/m64.html

   - SolidRun MACCHIATOBin based on Marvell Armada 8K:
        https://www.solid-run.com/marvell-armada-family/armada-8040-community-board/

   - Broadcom BCM958712DxXMC NorthStar2 reference board (another one)

  A lot of platforms improve support for existing machines by adding
  extra devices for which a binding and driver is availabe:

  Allwinner:
   - MMC, USB

  ARM Juno:
   - Coresight, STM

  Broadcom:
   - NS2 GICv2m irqchip and PCIe

  Marvell:
   - Armada 3700 SPI, I2C, ethernet switch

  Mediatek:
   - MT8173 thermal

  NXP i.MX:
   - LS1046A thermal

  Qualcomm:
   - coresight on MSM8916, HDMI, WCNSS, SCM

  Renesas:
   - r8a779[56] thermal, powerdomain, ethernet, sound, pwm, can, can fd

  Rockchip:
   - thermal, eDP, pinctrl enhancements

  Samsung:
   - TM2 touchkey, Exynos5433 HDMI and power management improvements

  UniPhier:
   - SD reset, eMMC controller

  ZTE:
   - oppv2 cpufreq"

* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (110 commits)
  arm64: dts: qcom: Add msm8916 CoreSight components
  arm64: dts: marvell: adjust name of sd-mmc-gop clock in syscon
  arm64: allwinner: add BananaPi-M64 support
  arm64: allwinner: a64: add UART1 pin nodes
  arm64: allwinner: pine64: add MMC support
  arm64: allwinner: a64: Increase the MMC max frequency
  arm64: allwinner: a64: Add MMC pinctrl nodes
  arm64: allwinner: a64: Add MMC nodes
  dt-bindings: clockgen: Add compatible string for LS1012A
  Documentation: DT: add LS1012A compatible for SCFG and DCFG
  Documentation: DT: Add entry for FSL LS1012A RDB, FRDM, QDS boards
  arm64: dts: marvell: add generic-ahci compatibles for CP110 ahci
  arm64: tegra: Use symbolic reset identifiers
  arm64: dts: r8a7796: Mark EthernetAVB device node disabled
  arm64: dts: r8a7795: Mark EthernetAVB device node disabled
  arm64: dts: r8a7795: tidyup audma definition order
  arm64: dts: r8a7796: Link ARM GIC to clock and clock domain
  arm64: dts: r8a7795: Link ARM GIC to clock and clock domain
  arm64: dts: r8a7796: Add R-Car Gen3 thermal support
  arm64: dts: r8a7795: Add R-Car Gen3 thermal support
  ...

Documentation/devicetree/bindings/arm/cpus.txt

@@ -158,6 +158,7 @@ nodes to be present and contain the properties described below.
 			    "arm,cortex-a53"
 			    "arm,cortex-a57"
 			    "arm,cortex-a72"
+			    "arm,cortex-a73"
 			    "arm,cortex-m0"
 			    "arm,cortex-m0+"
 			    "arm,cortex-m1"

Documentation/devicetree/bindings/arm/fsl.txt

@@ -108,7 +108,7 @@ status.
   - compatible: Should contain a chip-specific compatible string,
 	Chip-specific strings are of the form "fsl,<chip>-scfg",
 	The following <chip>s are known to be supported:
-	ls1021a, ls1043a, ls1046a, ls2080a.
+	ls1012a, ls1021a, ls1043a, ls1046a, ls2080a.
 
   - reg: should contain base address and length of SCFG memory-mapped registers
 
@@ -126,7 +126,7 @@ core start address and release the secondary core from holdoff and startup.
   - compatible: Should contain a chip-specific compatible string,
 	Chip-specific strings are of the form "fsl,<chip>-dcfg",
 	The following <chip>s are known to be supported:
-	ls1021a, ls1043a, ls1046a, ls2080a.
+	ls1012a, ls1021a, ls1043a, ls1046a, ls2080a.
 
   - reg : should contain base address and length of DCFG memory-mapped registers
 
@@ -139,6 +139,22 @@ Example:
 Freescale ARMv8 based Layerscape SoC family Device Tree Bindings
 ----------------------------------------------------------------
 
+LS1012A SoC
+Required root node properties:
+    - compatible = "fsl,ls1012a";
+
+LS1012A ARMv8 based RDB Board
+Required root node properties:
+    - compatible = "fsl,ls1012a-rdb", "fsl,ls1012a";
+
+LS1012A ARMv8 based FRDM Board
+Required root node properties:
+    - compatible = "fsl,ls1012a-frdm", "fsl,ls1012a";
+
+LS1012A ARMv8 based QDS Board
+Required root node properties:
+    - compatible = "fsl,ls1012a-qds", "fsl,ls1012a";
+
 LS1043A SoC
 Required root node properties:
     - compatible = "fsl,ls1043a";

Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt

 Hisilicon Platforms Device Tree Bindings
 ----------------------------------------------------
+Hi3660 SoC
+Required root node properties:
+	- compatible = "hisilicon,hi3660";
+
 Hi4511 Board
 Required root node properties:
 	- compatible = "hisilicon,hi3620-hi4511";

Documentation/devicetree/bindings/arm/shmobile.txt

@@ -75,7 +75,7 @@ Boards:
     compatible = "renesas,rskrza1", "renesas,r7s72100"
   - Salvator-X (RTP0RC7795SIPB0010S)
     compatible = "renesas,salvator-x", "renesas,r8a7795";
-  - Salvator-X
+  - Salvator-X (RTP0RC7796SIPB0011S)
     compatible = "renesas,salvator-x", "renesas,r8a7796";
   - SILK (RTP0RC7794LCB00011S)
     compatible = "renesas,silk", "renesas,r8a7794"

Documentation/devicetree/bindings/clock/qoriq-clock.txt

@@ -31,6 +31,7 @@ Required properties:
 	* "fsl,t4240-clockgen"
 	* "fsl,b4420-clockgen"
 	* "fsl,b4860-clockgen"
+	* "fsl,ls1012a-clockgen"
 	* "fsl,ls1021a-clockgen"
 	* "fsl,ls1043a-clockgen"
 	* "fsl,ls1046a-clockgen"

arch/arm64/boot/dts/allwinner/Makefile

+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-bananapi-m64.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
 
 always		:= $(dtb-y)

arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts

+/*
+ * Copyright (c) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "sun50i-a64.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "BananaPi-M64";
+	compatible = "sinovoip,bananapi-m64", "allwinner,sun50i-a64";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_vcc3v3: vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	status = "okay";
+};
+
+&i2c1_pins {
+	bias-pull-up;
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	status = "okay";
+};

arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts

@@ -44,6 +44,8 @@
 
 #include "sun50i-a64.dtsi"
 
+#include <dt-bindings/gpio/gpio.h>
+
 / {
 	model = "Pine64";
 	compatible = "pine64,pine64", "allwinner,sun50i-a64";
@@ -55,11 +57,16 @@ aliases {
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	reg_vcc3v3: vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 };
 
-&uart0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+&ehci1 {
 	status = "okay";
 };
 
@@ -72,3 +79,33 @@ &i2c1 {
 &i2c1_pins {
 	bias-pull-up;
 };
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};

arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi

@@ -42,8 +42,9 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
+#include <dt-bindings/clock/sun50i-a64-ccu.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/reset/sun50i-a64-ccu.h>
 
 / {
 	interrupt-parent = <&gic>;
@@ -120,6 +121,105 @@ soc {
 		#size-cells = <1>;
 		ranges;
 
+		mmc0: mmc@1c0f000 {
+			compatible = "allwinner,sun50i-a64-mmc";
+			reg = <0x01c0f000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC0>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			max-frequency = <150000000>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc1: mmc@1c10000 {
+			compatible = "allwinner,sun50i-a64-mmc";
+			reg = <0x01c10000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC1>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+			max-frequency = <150000000>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc2: mmc@1c11000 {
+			compatible = "allwinner,sun50i-a64-emmc";
+			reg = <0x01c11000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC2>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			max-frequency = <200000000>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		usb_otg: usb@01c19000 {
+			compatible = "allwinner,sun8i-a33-musb";
+			reg = <0x01c19000 0x0400>;
+			clocks = <&ccu CLK_BUS_OTG>;
+			resets = <&ccu RST_BUS_OTG>;
+			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "mc";
+			phys = <&usbphy 0>;
+			phy-names = "usb";
+			extcon = <&usbphy 0>;
+			status = "disabled";
+		};
+
+		usbphy: phy@01c19400 {
+			compatible = "allwinner,sun50i-a64-usb-phy";
+			reg = <0x01c19400 0x14>,
+			      <0x01c1b800 0x4>;
+			reg-names = "phy_ctrl",
+				    "pmu1";
+			clocks = <&ccu CLK_USB_PHY0>,
+				 <&ccu CLK_USB_PHY1>;
+			clock-names = "usb0_phy",
+				      "usb1_phy";
+			resets = <&ccu RST_USB_PHY0>,
+				 <&ccu RST_USB_PHY1>;
+			reset-names = "usb0_reset",
+				      "usb1_reset";
+			status = "disabled";
+			#phy-cells = <1>;
+		};
+
+		ehci1: usb@01c1b000 {
+			compatible = "allwinner,sun50i-a64-ehci", "generic-ehci";
+			reg = <0x01c1b000 0x100>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_OHCI1>,
+				 <&ccu CLK_BUS_EHCI1>,
+				 <&ccu CLK_USB_OHCI1>;
+			resets = <&ccu RST_BUS_OHCI1>,
+				 <&ccu RST_BUS_EHCI1>;
+			phys = <&usbphy 1>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		ohci1: usb@01c1b400 {
+			compatible = "allwinner,sun50i-a64-ohci", "generic-ohci";
+			reg = <0x01c1b400 0x100>;
+			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_OHCI1>,
+				 <&ccu CLK_USB_OHCI1>;
+			resets = <&ccu RST_BUS_OHCI1>;
+			phys = <&usbphy 1>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
 		ccu: clock@01c20000 {
 			compatible = "allwinner,sun50i-a64-ccu";
 			reg = <0x01c20000 0x400>;
@@ -146,10 +246,45 @@ i2c1_pins: i2c1_pins {
 				function = "i2c1";
 			};
 
+			mmc0_pins: mmc0-pins {
+				pins = "PF0", "PF1", "PF2", "PF3",
+				       "PF4", "PF5";
+				function = "mmc0";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			mmc1_pins: mmc1-pins {
+				pins = "PG0", "PG1", "PG2", "PG3",
+				       "PG4", "PG5";
+				function = "mmc1";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			mmc2_pins: mmc2-pins {
+				pins = "PC1", "PC5", "PC6", "PC8", "PC9",
+				       "PC10","PC11", "PC12", "PC13",
+				       "PC14", "PC15", "PC16";
+				function = "mmc2";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
 			uart0_pins_a: uart0@0 {
 				pins = "PB8", "PB9";
 				function = "uart0";
 			};
+
+			uart1_pins: uart1_pins {
+				pins = "PG6", "PG7";
+				function = "uart1";
+			};
+
+			uart1_rts_cts_pins: uart1_rts_cts_pins {
+				pins = "PG8", "PG9";
+				function = "uart1";
+			};
 		};
 
 		uart0: serial@1c28000 {

arch/arm64/boot/dts/arm/juno-base.dtsi

+#include "juno-clocks.dtsi"
+
+/ {
 	/*
 	 *  Devices shared by all Juno boards
 	 */
+	dma-ranges = <0 0 0 0 0x100 0>;
 
 	memtimer: timer@2a810000 {
 		compatible = "arm,armv7-timer-mem";
@@ -48,6 +52,7 @@ smmu_etr: iommu@2b600000 {
 		#iommu-cells = <1>;
 		#global-interrupts = <1>;
 		dma-coherent;
+		power-domains = <&scpi_devpd 0>;
 		status = "disabled";
 	};
 
@@ -83,7 +88,7 @@ timer {
 	 * The actual size is just 4K though 64K is reserved. Access to the
 	 * unmapped reserved region results in a DECERR response.
 	 */
-	etf@20010000 {
+	etf@20010000 { /* etf0 */
 		compatible = "arm,coresight-tmc", "arm,primecell";
 		reg = <0 0x20010000 0 0x1000>;
 
@@ -97,7 +102,7 @@ ports {
 			/* input port */
 			port@0 {
 				reg = <0>;
-				etf_in_port: endpoint {
+				etf0_in_port: endpoint {
 					slave-mode;
 					remote-endpoint = <&main_funnel_out_port>;
 				};
@@ -106,8 +111,7 @@ etf_in_port: endpoint {
 			/* output port */
 			port@1 {
 				reg = <0>;
-				etf_out_port: endpoint {
-					remote-endpoint = <&replicator_in_port0>;
+				etf0_out_port: endpoint {
 				};
 			};
 		};
@@ -128,7 +132,8 @@ tpiu_in_port: endpoint {
 		};
 	};
 
-	main-funnel@20040000 {
+	/* main funnel on Juno r0, cssys0 funnel on Juno r1/r2 as per TRM*/
+	main_funnel: funnel@20040000 {
 		compatible = "arm,coresight-funnel", "arm,primecell";
 		reg = <0 0x20040000 0 0x1000>;
 
@@ -139,13 +144,15 @@ ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
+			/* output port */
 			port@0 {
 				reg = <0>;
 				main_funnel_out_port: endpoint {
-					remote-endpoint = <&etf_in_port>;
+					remote-endpoint = <&etf0_in_port>;
 				};
 			};
 
+			/* input ports */
 			port@1 {
 				reg = <0>;
 				main_funnel_in_port0: endpoint {
@@ -161,7 +168,6 @@ main_funnel_in_port1: endpoint {
 					remote-endpoint = <&cluster1_funnel_out_port>;
 				};
 			};
-
 		};
 	};
 
@@ -181,6 +187,21 @@ etr_in_port: endpoint {
 		};
 	};
 
+	stm@20100000 {
+		compatible = "arm,coresight-stm", "arm,primecell";
+		reg = <0 0x20100000 0 0x1000>,
+		      <0 0x28000000 0 0x1000000>;
+		reg-names = "stm-base", "stm-stimulus-base";
+
+		clocks = <&soc_smc50mhz>;
+		clock-names = "apb_pclk";
+		power-domains = <&scpi_devpd 0>;
+		port {
+			stm_out_port: endpoint {
+			};
+		};
+	};
+
 	etm0: etm@22040000 {
 		compatible = "arm,coresight-etm4x", "arm,primecell";
 		reg = <0 0x22040000 0 0x1000>;
@@ -195,7 +216,7 @@ cluster0_etm0_out_port: endpoint {
 		};
 	};
 
-	cluster0-funnel@220c0000 {
+	funnel@220c0000 { /* cluster0 funnel */
 		compatible = "arm,coresight-funnel", "arm,primecell";
 		reg = <0 0x220c0000 0 0x1000>;
 
@@ -259,7 +280,7 @@ cluster1_etm0_out_port: endpoint {
 		};
 	};
 
-	cluster1-funnel@230c0000 {
+	funnel@230c0000 { /* cluster1 funnel */
 		compatible = "arm,coresight-funnel", "arm,primecell";
 		reg = <0 0x230c0000 0 0x1000>;
 
@@ -382,7 +403,6 @@ port@2 {
 				reg = <0>;
 				replicator_in_port0: endpoint {
 					slave-mode;
-					remote-endpoint = <&etf_out_port>;
 				};
 			};
 		};
@@ -507,8 +527,6 @@ gpu1_thermal_zone: gpu1 {
 		};
 	};
 
-	/include/ "juno-clocks.dtsi"
-
 	smmu_dma: iommu@7fb00000 {
 		compatible = "arm,mmu-401", "arm,smmu-v1";
 		reg = <0x0 0x7fb00000 0x0 0x10000>;
@@ -719,3 +737,4 @@ site2: tlx@60000000 {
 		interrupt-map-mask = <0 0>;
 		interrupt-map = <0 0 &gic 0 0 0 168 IRQ_TYPE_LEVEL_HIGH>;
 	};
+};

arch/arm64/boot/dts/arm/juno-clocks.dtsi

@@ -6,7 +6,7 @@
  * This file is licensed under a dual GPLv2 or BSD license.
  *
  */
-
+/ {
 	/* SoC fixed clocks */
 	soc_uartclk: refclk7273800hz {
 		compatible = "fixed-clock";
@@ -42,3 +42,4 @@ soc_faxiclk: refclk400mhz {
 		clock-frequency = <400000000>;
 		clock-output-names = "faxi_clk";
 	};
+};

arch/arm64/boot/dts/arm/juno-cs-r1r2.dtsi

+/ {
+	funnel@20130000 { /* cssys1 */
+		compatible = "arm,coresight-funnel", "arm,primecell";
+		reg = <0 0x20130000 0 0x1000>;
+
+		clocks = <&soc_smc50mhz>;
+		clock-names = "apb_pclk";
+		power-domains = <&scpi_devpd 0>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* output port */
+			port@0 {
+				reg = <0>;
+				csys1_funnel_out_port: endpoint {
+					remote-endpoint = <&etf1_in_port>;
+				};
+			};
+
+			/* input port */
+			port@1 {
+				reg = <0>;
+				csys1_funnel_in_port0: endpoint {
+					slave-mode;
+				};
+			};
+
+		};
+	};
+
+	etf@20140000 { /* etf1 */
+		compatible = "arm,coresight-tmc", "arm,primecell";
+		reg = <0 0x20140000 0 0x1000>;
+
+		clocks = <&soc_smc50mhz>;
+		clock-names = "apb_pclk";
+		power-domains = <&scpi_devpd 0>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* input port */
+			port@0 {
+				reg = <0>;
+				etf1_in_port: endpoint {
+					slave-mode;
+					remote-endpoint = <&csys1_funnel_out_port>;
+				};
+			};
+
+			/* output port */
+			port@1 {
+				reg = <0>;
+				etf1_out_port: endpoint {
+					remote-endpoint = <&csys2_funnel_in_port1>;
+				};
+			};
+		};
+	};
+
+	funnel@20150000 { /* cssys2 */
+		compatible = "arm,coresight-funnel", "arm,primecell";
+		reg = <0 0x20150000 0 0x1000>;
+
+		clocks = <&soc_smc50mhz>;
+		clock-names = "apb_pclk";
+		power-domains = <&scpi_devpd 0>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* output port */
+			port@0 {
+				reg = <0>;
+				csys2_funnel_out_port: endpoint {
+					remote-endpoint = <&replicator_in_port0>;
+				};
+			};
+
+			/* input ports */
+			port@1 {
+				reg = <0>;
+				csys2_funnel_in_port0: endpoint {
+					slave-mode;
+					remote-endpoint = <&etf0_out_port>;
+				};
+			};
+
+			port@2 {
+				reg = <1>;
+				csys2_funnel_in_port1: endpoint {
+					slave-mode;
+					remote-endpoint = <&etf1_out_port>;
+				};
+			};
+
+		};
+	};
+};

arch/arm64/boot/dts/arm/juno-motherboard.dtsi

@@ -131,13 +131,6 @@ ethernet@2,00000000 {
 				vddvario-supply = <&mb_fixed_3v3>;
 			};
 
-			usb@5,00000000 {
-				compatible = "nxp,usb-isp1763";
-				reg = <5 0x00000000 0x20000>;
-				bus-width = <16>;
-				interrupts = <4>;
-			};
-
 			iofpga@3,00000000 {
 				compatible = "simple-bus";
 				#address-cells = <1>;

arch/arm64/boot/dts/arm/juno-r1.dts

@@ -9,6 +9,8 @@
 /dts-v1/;
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "juno-base.dtsi"
+#include "juno-cs-r1r2.dtsi"
 
 / {
 	model = "ARM Juno development board (r1)";
@@ -176,8 +178,6 @@ pmu_a53 {
 				     <&A53_2>,
 				     <&A53_3>;
 	};
-
-	#include "juno-base.dtsi"
 };
 
 &memtimer {
@@ -227,3 +227,15 @@ &gpu0_thermal_zone {
 &gpu1_thermal_zone {
 	status = "okay";
 };
+
+&etf0_out_port {
+	remote-endpoint = <&csys2_funnel_in_port0>;
+};
+
+&replicator_in_port0 {
+	remote-endpoint = <&csys2_funnel_out_port>;
+};
+
+&stm_out_port {
+	remote-endpoint = <&csys1_funnel_in_port0>;
+};

arch/arm64/boot/dts/arm/juno-r2.dts

@@ -9,6 +9,8 @@
 /dts-v1/;
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "juno-base.dtsi"
+#include "juno-cs-r1r2.dtsi"
 
 / {
 	model = "ARM Juno development board (r2)";
@@ -176,8 +178,6 @@ pmu_a53 {
 				     <&A53_2>,
 				     <&A53_3>;
 	};
-
-	#include "juno-base.dtsi"
 };
 
 &memtimer {
@@ -227,3 +227,15 @@ &gpu0_thermal_zone {
 &gpu1_thermal_zone {
 	status = "okay";
 };
+
+&etf0_out_port {
+	remote-endpoint = <&csys2_funnel_in_port0>;
+};
+
+&replicator_in_port0 {
+	remote-endpoint = <&csys2_funnel_out_port>;
+};
+
+&stm_out_port {
+	remote-endpoint = <&csys1_funnel_in_port0>;
+};

arch/arm64/boot/dts/arm/juno.dts

@@ -9,6 +9,7 @@
 /dts-v1/;
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "juno-base.dtsi"
 
 / {
 	model = "ARM Juno development board (r0)";
@@ -176,8 +177,6 @@ pmu_a53 {
 				     <&A53_2>,
 				     <&A53_3>;
 	};
-
-	#include "juno-base.dtsi"
 };
 
 &etm0 {
@@ -203,3 +202,27 @@ &etm4 {
 &etm5 {
 	cpu = <&A53_3>;
 };
+
+&etf0_out_port {
+	remote-endpoint = <&replicator_in_port0>;
+};
+
+&replicator_in_port0 {
+	remote-endpoint = <&etf0_out_port>;
+};
+
+&stm_out_port {
+	remote-endpoint = <&main_funnel_in_port2>;
+};
+
+&main_funnel {
+	ports {
+		port@3 {
+			reg = <2>;
+			main_funnel_in_port2: endpoint {
+				slave-mode;
+				remote-endpoint = <&stm_out_port>;
+			};
+		};
+	};
+};

arch/arm64/boot/dts/broadcom/Makefile

 dtb-$(CONFIG_ARCH_BCM2835) += bcm2837-rpi-3-b.dtb
-dtb-$(CONFIG_ARCH_BCM_IPROC) += ns2-svk.dtb
+dtb-$(CONFIG_ARCH_BCM_IPROC) += ns2-svk.dtb ns2-xmc.dtb
 dtb-$(CONFIG_ARCH_VULCAN) += vulcan-eval.dtb
 
 always		:= $(dtb-y)

arch/arm64/boot/dts/broadcom/ns2-svk.dts

@@ -76,6 +76,10 @@ &pcie4 {
 	status = "ok";
 };
 
+&pcie8 {
+	status = "ok";
+};
+
 &i2c0 {
 	status = "ok";
 };

arch/arm64/boot/dts/broadcom/ns2-xmc.dts

+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2016 Broadcom.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "ns2.dtsi"
+
+/ {
+	model = "Broadcom NS2 XMC";
+	compatible = "brcm,ns2-xmc", "brcm,ns2";
+
+	aliases {
+		serial0 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+		bootargs = "earlycon=uart8250,mmio32,0x66130000";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x000000000 0x80000000 0x00000001 0x00000000>;
+	};
+};
+
+&enet {
+	status = "ok";
+};
+
+&i2c0 {
+	status = "ok";
+};
+
+&i2c1 {
+	status = "ok";
+};
+
+&mdio_mux_iproc {
+	mdio@10 {
+		gphy0: eth-phy@10 {
+			reg = <0x10>;
+		};
+	};
+};
+
+&nand {
+	nandcs@0 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-ecc-mode = "hw";
+		nand-ecc-strength = <8>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <16>;
+		brcm,nand-oob-sector-size = <16>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "nboot";
+			reg = <0x00000000 0x00280000>; /*  2.5MB */
+			read-only;
+		};
+
+		partition@280000 {
+			label = "nenv";
+			reg = <0x00280000 0x00040000>; /* 0.25MB */
+			read-only;
+		};
+
+		partition@2c0000 {
+			label = "ndtb";
+			reg = <0x002c0000 0x00040000>; /* 0.25MB */
+			read-only;
+		};
+
+		partition@300000 {
+			label = "nsystem";
+			reg = <0x00300000 0x03d00000>; /*   61MB */
+			read-only;
+		};
+
+		partition@4000000 {
+			label = "nrootfs";
+			reg = <0x04000000 0x06400000>; /*  100MB */
+		};
+
+		partition@0a400000{
+			label = "ncustfs";
+			reg = <0x0a400000 0x35c00000>; /*  860MB */
+		};
+	};
+};
+
+&pci_phy0 {
+	status = "ok";
+};
+
+&pcie0 {
+	status = "ok";
+};
+
+&pcie8 {
+	status = "ok";
+};
+
+&sata_phy0 {
+	status = "ok";
+};
+
+&sata_phy1 {
+	status = "ok";
+};
+
+&sata {
+	status = "ok";
+};
+
+&qspi {
+	flash: m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p80";
+		spi-max-frequency = <62500000>;
+		m25p,default-addr-width = <3>;
+		reg = <0x0 0x0>;
+
+		partition@0 {
+			label = "bl0";
+			reg = <0x00000000 0x00080000>; /*  512KB */
+		};
+
+		partition@80000 {
+			label = "fip";
+			reg = <0x00080000 0x00150000>; /* 1344KB */
+		};
+
+		partition@1e0000 {
+			label = "env";
+			reg = <0x001e0000 0x00010000>;/*    64KB */
+		};
+
+		partition@1f0000 {
+			label = "dtb";
+			reg = <0x001f0000 0x00010000>; /*   64KB */
+		};
+
+		partition@200000 {
+			label = "kernel";
+			reg = <0x00200000 0x00e00000>; /*   14MB */
+		};
+
+		partition@1000000 {
+			label = "rootfs";
+			reg = <0x01000000 0x01000000>; /*   16MB */
+		};
+	};
+};
+
+&uart3 {
+	status = "ok";
+};

arch/arm64/boot/dts/broadcom/ns2.dtsi

@@ -30,6 +30,8 @@
  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  */
 
+/memreserve/ 0x81000000 0x00200000;
+
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/bcm-ns2.h>
 
@@ -115,7 +117,7 @@ pcie0: pcie@20020000 {
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 281 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 281 IRQ_TYPE_NONE>;
 
 		linux,pci-domain = <0>;
 
@@ -136,18 +138,7 @@ pcie0: pcie@20020000 {
 		phys = <&pci_phy0>;
 		phy-names = "pcie-phy";
 
-		msi-parent = <&msi0>;
-		msi0: msi@20020000 {
-			compatible = "brcm,iproc-msi";
-			msi-controller;
-			interrupt-parent = <&gic>;
-			interrupts = <GIC_SPI 277 IRQ_TYPE_NONE>,
-				     <GIC_SPI 278 IRQ_TYPE_NONE>,
-				     <GIC_SPI 279 IRQ_TYPE_NONE>,
-				     <GIC_SPI 280 IRQ_TYPE_NONE>;
-			brcm,num-eq-region = <1>;
-			brcm,num-msi-msg-region = <1>;
-		};
+		msi-parent = <&v2m0>;
 	};
 
 	pcie4: pcie@50020000 {
@@ -156,7 +147,7 @@ pcie4: pcie@50020000 {
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 305 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 305 IRQ_TYPE_NONE>;
 
 		linux,pci-domain = <4>;
 
@@ -177,16 +168,24 @@ pcie4: pcie@50020000 {
 		phys = <&pci_phy1>;
 		phy-names = "pcie-phy";
 
-		msi-parent = <&msi4>;
-		msi4: msi@50020000 {
-			compatible = "brcm,iproc-msi";
-			msi-controller;
-			interrupt-parent = <&gic>;
-			interrupts = <GIC_SPI 301 IRQ_TYPE_NONE>,
-				     <GIC_SPI 302 IRQ_TYPE_NONE>,
-				     <GIC_SPI 303 IRQ_TYPE_NONE>,
-				     <GIC_SPI 304 IRQ_TYPE_NONE>;
+		msi-parent = <&v2m0>;
 	};
+
+	pcie8: pcie@60c00000 {
+		compatible = "brcm,iproc-pcie-paxc";
+		reg = <0 0x60c00000 0 0x1000>;
+		linux,pci-domain = <8>;
+
+		bus-range = <0x0 0x1>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		ranges = <0x83000000 0 0x00000000 0 0x60000000 0 0x00c00000>;
+
+		status = "disabled";
+
+		msi-parent = <&v2m0>;
 	};
 
 	soc: soc {
@@ -331,6 +330,82 @@ gic: interrupt-controller@65210000 {
 			      <0x65260000 0x1000>;
 			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_RAW(0xf) |
 				      IRQ_TYPE_LEVEL_HIGH)>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x652e0000 0x80000>;
+
+			v2m0: v2m@00000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x00000 0x1000>;
+				arm,msi-base-spi = <72>;
+				arm,msi-num-spis = <16>;
+			};
+
+			v2m1: v2m@10000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x10000 0x1000>;
+				arm,msi-base-spi = <88>;
+				arm,msi-num-spis = <16>;
+			};
+
+			v2m2: v2m@20000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x20000 0x1000>;
+				arm,msi-base-spi = <104>;
+				arm,msi-num-spis = <16>;
+			};
+
+			v2m3: v2m@30000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x30000 0x1000>;
+				arm,msi-base-spi = <120>;
+				arm,msi-num-spis = <16>;
+			};
+
+			v2m4: v2m@40000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x40000 0x1000>;
+				arm,msi-base-spi = <136>;
+				arm,msi-num-spis = <16>;
+			};
+
+			v2m5: v2m@50000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x50000 0x1000>;
+				arm,msi-base-spi = <152>;
+				arm,msi-num-spis = <16>;
+			};
+
+			v2m6: v2m@60000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x60000 0x1000>;
+				arm,msi-base-spi = <168>;
+				arm,msi-num-spis = <16>;
+			};
+
+			v2m7: v2m@70000 {
+				compatible = "arm,gic-v2m-frame";
+				interrupt-parent = <&gic>;
+				msi-controller;
+				reg = <0x70000 0x1000>;
+				arm,msi-base-spi = <184>;
+				arm,msi-num-spis = <16>;
+			};
 		};
 
 		cci@65590000 {

arch/arm64/boot/dts/exynos/exynos5433-bus.dtsi

+/*
+ * Samsung's Exynos5433 SoC Memory interface and AMBA bus device tree source
+ *
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd.
+ * Chanwoo Choi <cw00.choi@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+&soc {
+	bus_g2d_400: bus0 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_top CLK_ACLK_G2D_400>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_g2d_400_opp_table>;
+		status = "disabled";
+	};
+
+	bus_g2d_266: bus1 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_top CLK_ACLK_G2D_266>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_g2d_266_opp_table>;
+		status = "disabled";
+	};
+
+	bus_gscl: bus2 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_top CLK_ACLK_GSCL_333>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_gscl_opp_table>;
+		status = "disabled";
+	};
+
+	bus_hevc: bus3 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_top CLK_ACLK_HEVC_400>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_hevc_opp_table>;
+		status = "disabled";
+	};
+
+	bus_jpeg: bus4 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_top CLK_SCLK_JPEG_MSCL>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_g2d_400_opp_table>;
+		status = "disabled";
+	};
+
+	bus_mfc: bus5 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_top CLK_ACLK_MFC_400>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_g2d_400_opp_table>;
+		status = "disabled";
+	};
+
+	bus_mscl: bus6 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_top CLK_ACLK_MSCL_400>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_g2d_400_opp_table>;
+		status = "disabled";
+	};
+
+	bus_noc0: bus7 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_top CLK_ACLK_BUS0_400>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_hevc_opp_table>;
+		status = "disabled";
+	};
+
+	bus_noc1: bus8 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_top CLK_ACLK_BUS1_400>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_hevc_opp_table>;
+		status = "disabled";
+	};
+
+	bus_noc2: bus9 {
+		compatible = "samsung,exynos-bus";
+		clocks = <&cmu_mif CLK_ACLK_BUS2_400>;
+		clock-names = "bus";
+		operating-points-v2 = <&bus_noc2_opp_table>;
+		status = "disabled";
+	};
+
+	bus_g2d_400_opp_table: opp_table2 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp@400000000 {
+			opp-hz = /bits/ 64 <400000000>;
+			opp-microvolt = <1075000>;
+		};
+		opp@267000000 {
+			opp-hz = /bits/ 64 <267000000>;
+			opp-microvolt = <1000000>;
+		};
+		opp@200000000 {
+			opp-hz = /bits/ 64 <200000000>;
+			opp-microvolt = <975000>;
+		};
+		opp@160000000 {
+			opp-hz = /bits/ 64 <160000000>;
+			opp-microvolt = <962500>;
+		};
+		opp@134000000 {
+			opp-hz = /bits/ 64 <134000000>;
+			opp-microvolt = <950000>;
+		};
+		opp@100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+			opp-microvolt = <937500>;
+		};
+	};
+
+	bus_g2d_266_opp_table: opp_table3 {
+		compatible = "operating-points-v2";
+
+		opp@267000000 {
+			opp-hz = /bits/ 64 <267000000>;
+		};
+		opp@200000000 {
+			opp-hz = /bits/ 64 <200000000>;
+		};
+		opp@160000000 {
+			opp-hz = /bits/ 64 <160000000>;
+		};
+		opp@134000000 {
+			opp-hz = /bits/ 64 <134000000>;
+		};
+		opp@100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+	};
+
+	bus_gscl_opp_table: opp_table4 {
+		compatible = "operating-points-v2";
+
+		opp@333000000 {
+			opp-hz = /bits/ 64 <333000000>;
+		};
+		opp@222000000 {
+			opp-hz = /bits/ 64 <222000000>;
+		};
+		opp@166500000 {
+			opp-hz = /bits/ 64 <166500000>;
+		};
+	};
+
+	bus_hevc_opp_table: opp_table5 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp@400000000 {
+			opp-hz = /bits/ 64 <400000000>;
+		};
+		opp@267000000 {
+			opp-hz = /bits/ 64 <267000000>;
+		};
+		opp@200000000 {
+			opp-hz = /bits/ 64 <200000000>;
+		};
+		opp@160000000 {
+			opp-hz = /bits/ 64 <160000000>;
+		};
+		opp@134000000 {
+			opp-hz = /bits/ 64 <134000000>;
+		};
+		opp@100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+	};
+
+	bus_noc2_opp_table: opp_table6 {
+		compatible = "operating-points-v2";
+
+		opp@400000000 {
+			opp-hz = /bits/ 64 <400000000>;
+		};
+		opp@200000000 {
+			opp-hz = /bits/ 64 <200000000>;
+		};
+		opp@134000000 {
+			opp-hz = /bits/ 64 <134000000>;
+		};
+		opp@100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+	};
+};

arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts

@@ -11,23 +11,13 @@
  * published by the Free Software Foundation.
  */
 
-#include "exynos5433-tm2.dts"
+#include "exynos5433-tm2-common.dtsi"
 
 / {
 	model = "Samsung TM2E board";
 	compatible = "samsung,tm2e", "samsung,exynos5433";
 };
 
-&ldo23_reg {
-	regulator-name = "CAM_SEN_CORE_1.025V_AP";
-	regulator-max-microvolt = <1050000>;
-};
-
-&ldo25_reg {
-	regulator-name = "UNUSED_LDO25";
-	regulator-always-off;
-};
-
 &ldo31_reg {
 	regulator-name = "TSP_VDD_1.8V_AP";
 	regulator-min-microvolt = <1800000>;

arch/arm64/boot/dts/exynos/exynos5433.dtsi

@@ -299,7 +299,7 @@ cmu_peric: clock-controller@14c80000 {
 			#clock-cells = <1>;
 		};
 
-		cmu_peris: clock-controller@0x10040000 {
+		cmu_peris: clock-controller@10040000 {
 			compatible = "samsung,exynos5433-cmu-peris";
 			reg = <0x10040000 0x1000>;
 			#clock-cells = <1>;
@@ -599,6 +599,30 @@ mct@101c0000 {
 			clock-names = "fin_pll", "mct";
 		};
 
+		ppmu_d0_cpu: ppmu@10480000 {
+			compatible = "samsung,exynos-ppmu-v2";
+			reg = <0x10480000 0x2000>;
+			status = "disabled";
+		};
+
+		ppmu_d0_general: ppmu@10490000 {
+			compatible = "samsung,exynos-ppmu-v2";
+			reg = <0x10490000 0x2000>;
+			status = "disabled";
+		};
+
+		ppmu_d1_cpu: ppmu@104b0000 {
+			compatible = "samsung,exynos-ppmu-v2";
+			reg = <0x104b0000 0x2000>;
+			status = "disabled";
+		};
+
+		ppmu_d1_general: ppmu@104c0000 {
+			compatible = "samsung,exynos-ppmu-v2";
+			reg = <0x104c0000 0x2000>;
+			status = "disabled";
+		};
+
 		pinctrl_alive: pinctrl@10580000 {
 			compatible = "samsung,exynos5433-pinctrl";
 			reg = <0x10580000 0x1a20>, <0x11090000 0x100>;
@@ -682,7 +706,7 @@ gic: interrupt-controller@11001000 {
 			interrupts = <GIC_PPI 9 0xf04>;
 		};
 
-		mipi_phy: video-phy@105c0710 {
+		mipi_phy: video-phy {
 			compatible = "samsung,exynos5433-mipi-video-phy";
 			#phy-cells = <1>;
 			samsung,pmu-syscon = <&pmu_system_controller>;
@@ -727,6 +751,29 @@ decon_to_mic: endpoint {
 			};
 		};
 
+		decon_tv: decon@13880000 {
+			compatible = "samsung,exynos5433-decon-tv";
+			reg = <0x13880000 0x20b8>;
+			clocks = <&cmu_disp CLK_PCLK_DECON_TV>,
+				 <&cmu_disp CLK_ACLK_DECON_TV>,
+				 <&cmu_disp CLK_ACLK_SMMU_TV0X>,
+				 <&cmu_disp CLK_ACLK_XIU_TV0X>,
+				 <&cmu_disp CLK_PCLK_SMMU_TV0X>,
+				 <&cmu_disp CLK_SCLK_DECON_TV_VCLK>,
+				 <&cmu_disp CLK_SCLK_DECON_TV_ECLK>;
+			clock-names = "pclk", "aclk_decon", "aclk_smmu_decon0x",
+				      "aclk_xiu_decon0x", "pclk_smmu_decon0x",
+				      "sclk_decon_vclk", "sclk_decon_eclk";
+			samsung,disp-sysreg = <&syscon_disp>;
+			interrupt-names = "fifo", "vsync", "lcd_sys";
+			interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			iommus = <&sysmmu_tv0x>, <&sysmmu_tv1x>;
+			iommu-names = "m0", "m1";
+		};
+
 		dsi: dsi@13900000 {
 			compatible = "samsung,exynos5433-mipi-dsi";
 			reg = <0x13900000 0xC0>;
@@ -790,6 +837,35 @@ mic_to_dsi: endpoint {
 			};
 		};
 
+		hdmi: hdmi@13970000 {
+			compatible = "samsung,exynos5433-hdmi";
+			reg = <0x13970000 0x70000>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu_disp CLK_PCLK_HDMI>,
+				<&cmu_disp CLK_PCLK_HDMIPHY>,
+				<&cmu_disp CLK_PHYCLK_HDMIPHY_TMDS_CLKO>,
+				<&cmu_disp CLK_PHYCLK_HDMI_PIXEL>,
+				<&cmu_disp CLK_PHYCLK_HDMIPHY_TMDS_CLKO_PHY>,
+				<&cmu_disp CLK_MOUT_PHYCLK_HDMIPHY_TMDS_CLKO_USER>,
+				<&cmu_disp CLK_PHYCLK_HDMIPHY_PIXEL_CLKO_PHY>,
+				<&cmu_disp CLK_MOUT_PHYCLK_HDMIPHY_PIXEL_CLKO_USER>,
+				<&xxti>, <&cmu_disp CLK_SCLK_HDMI_SPDIF>;
+			clock-names = "hdmi_pclk", "hdmi_i_pclk",
+				"i_tmds_clk", "i_pixel_clk",
+				"tmds_clko", "tmds_clko_user",
+				"pixel_clko", "pixel_clko_user",
+				"oscclk", "i_spdif_clk";
+			phy = <&hdmiphy>;
+			ddc = <&hsi2c_11>;
+			samsung,syscon-phandle = <&pmu_system_controller>;
+			samsung,sysreg-phandle = <&syscon_disp>;
+			status = "disabled";
+		};
+
+		hdmiphy: hdmiphy@13af0000 {
+			reg = <0x13af0000 0x80>;
+		};
+
 		syscon_disp: syscon@13b80000 {
 			compatible = "syscon";
 			reg = <0x13b80000 0x1010>;
@@ -868,7 +944,7 @@ mfc: codec@152E0000 {
 			iommu-names = "left", "right";
 		};
 
-		sysmmu_decon0x: sysmmu@0x13a00000 {
+		sysmmu_decon0x: sysmmu@13a00000 {
 			compatible = "samsung,exynos-sysmmu";
 			reg = <0x13a00000 0x1000>;
 			interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
@@ -878,7 +954,7 @@ sysmmu_decon0x: sysmmu@0x13a00000 {
 			#iommu-cells = <0>;
 		};
 
-		sysmmu_decon1x: sysmmu@0x13a10000 {
+		sysmmu_decon1x: sysmmu@13a10000 {
 			compatible = "samsung,exynos-sysmmu";
 			reg = <0x13a10000 0x1000>;
 			interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
@@ -888,7 +964,27 @@ sysmmu_decon1x: sysmmu@0x13a10000 {
 			#iommu-cells = <0>;
 		};
 
-		sysmmu_gscl0: sysmmu@0x13C80000 {
+		sysmmu_tv0x: sysmmu@13a20000 {
+			compatible = "samsung,exynos-sysmmu";
+			reg = <0x13a20000 0x1000>;
+			interrupts = <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "pclk", "aclk";
+			clocks = <&cmu_disp CLK_PCLK_SMMU_TV0X>,
+				<&cmu_disp CLK_ACLK_SMMU_TV0X>;
+			#iommu-cells = <0>;
+		};
+
+		sysmmu_tv1x: sysmmu@13a30000 {
+			compatible = "samsung,exynos-sysmmu";
+			reg = <0x13a30000 0x1000>;
+			interrupts = <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "pclk", "aclk";
+			clocks = <&cmu_disp CLK_PCLK_SMMU_TV1X>,
+				<&cmu_disp CLK_ACLK_SMMU_TV1X>;
+			#iommu-cells = <0>;
+		};
+
+		sysmmu_gscl0: sysmmu@13c80000 {
 			compatible = "samsung,exynos-sysmmu";
 			reg = <0x13C80000 0x1000>;
 			interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
@@ -898,7 +994,7 @@ sysmmu_gscl0: sysmmu@0x13C80000 {
 			#iommu-cells = <0>;
 		};
 
-		sysmmu_gscl1: sysmmu@0x13C90000 {
+		sysmmu_gscl1: sysmmu@13c90000 {
 			compatible = "samsung,exynos-sysmmu";
 			reg = <0x13C90000 0x1000>;
 			interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
@@ -908,7 +1004,7 @@ sysmmu_gscl1: sysmmu@0x13C90000 {
 			#iommu-cells = <0>;
 		};
 
-		sysmmu_gscl2: sysmmu@0x13CA0000 {
+		sysmmu_gscl2: sysmmu@13ca0000 {
 			compatible = "samsung,exynos-sysmmu";
 			reg = <0x13CA0000 0x1000>;
 			interrupts = <GIC_SPI 292 IRQ_TYPE_LEVEL_HIGH>;
@@ -918,7 +1014,7 @@ sysmmu_gscl2: sysmmu@0x13CA0000 {
 			#iommu-cells = <0>;
 		};
 
-		sysmmu_jpeg: sysmmu@0x15060000 {
+		sysmmu_jpeg: sysmmu@15060000 {
 			compatible = "samsung,exynos-sysmmu";
 			reg = <0x15060000 0x1000>;
 			interrupts = <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>;
@@ -928,7 +1024,7 @@ sysmmu_jpeg: sysmmu@0x15060000 {
 			#iommu-cells = <0>;
 		};
 
-		sysmmu_mfc_0: sysmmu@0x15200000 {
+		sysmmu_mfc_0: sysmmu@15200000 {
 			compatible = "samsung,exynos-sysmmu";
 			reg = <0x15200000 0x1000>;
 			interrupts = <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
@@ -938,7 +1034,7 @@ sysmmu_mfc_0: sysmmu@0x15200000 {
 			#iommu-cells = <0>;
 		};
 
-		sysmmu_mfc_1: sysmmu@0x15210000 {
+		sysmmu_mfc_1: sysmmu@15210000 {
 			compatible = "samsung,exynos-sysmmu";
 			reg = <0x15210000 0x1000>;
 			interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
@@ -1261,7 +1357,7 @@ hsi2c_11: hsi2c@14df0000 {
 			status = "disabled";
 		};
 
-		usbdrd30: usb@15400000  {
+		usbdrd30: usbdrd {
 			compatible = "samsung,exynos5250-dwusb3";
 			clocks = <&cmu_fsys CLK_ACLK_USBDRD30>,
 				<&cmu_fsys CLK_SCLK_USBDRD30>;
@@ -1308,7 +1404,7 @@ usbhost30_phy: phy@15580000 {
 			status = "disabled";
 		};
 
-		usbhost30: usb@15a00000 {
+		usbhost30: usbhost {
 			compatible = "samsung,exynos5250-dwusb3";
 			clocks = <&cmu_fsys CLK_ACLK_USBHOST30>,
 				<&cmu_fsys CLK_SCLK_USBHOST30>;
@@ -1398,6 +1494,8 @@ pdma1: pdma@15600000 {
 		audio-subsystem@11400000 {
 			compatible = "samsung,exynos5433-lpass";
 			reg = <0x11400000 0x100>, <0x11500000 0x08>;
+			clocks = <&cmu_aud CLK_PCLK_SFR0_CTRL>;
+			clock-names = "sfr0_ctrl";
 			samsung,pmu-syscon = <&pmu_system_controller>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -1458,5 +1556,6 @@ timer: timer {
 	};
 };
 
+#include "exynos5433-bus.dtsi"
 #include "exynos5433-pinctrl.dtsi"
 #include "exynos5433-tmu.dtsi"

arch/arm64/boot/dts/exynos/exynos7-pinctrl.dtsi

@@ -497,49 +497,49 @@ sd0_clk: sd0-clk {
 		samsung,pins = "gpr0-0";
 		samsung,pin-function = <2>;
 		samsung,pin-pud = <0>;
-		samsung,pin-drv = <3>;
+		samsung,pin-drv = <4>;
 	};
 
 	sd0_cmd: sd0-cmd {
 		samsung,pins = "gpr0-1";
 		samsung,pin-function = <2>;
 		samsung,pin-pud = <3>;
-		samsung,pin-drv = <3>;
+		samsung,pin-drv = <4>;
 	};
 
 	sd0_ds: sd0-ds {
 		samsung,pins = "gpr0-2";
 		samsung,pin-function = <2>;
 		samsung,pin-pud = <1>;
-		samsung,pin-drv = <3>;
+		samsung,pin-drv = <4>;
 	};
 
 	sd0_qrdy: sd0-qrdy {
 		samsung,pins = "gpr0-3";
 		samsung,pin-function = <2>;
 		samsung,pin-pud = <1>;
-		samsung,pin-drv = <3>;
+		samsung,pin-drv = <4>;
 	};
 
 	sd0_bus1: sd0-bus-width1 {
 		samsung,pins = "gpr1-0";
 		samsung,pin-function = <2>;
 		samsung,pin-pud = <3>;
-		samsung,pin-drv = <3>;
+		samsung,pin-drv = <4>;
 	};
 
 	sd0_bus4: sd0-bus-width4 {
 		samsung,pins = "gpr1-1", "gpr1-2", "gpr1-3";
 		samsung,pin-function = <2>;
 		samsung,pin-pud = <3>;
-		samsung,pin-drv = <3>;
+		samsung,pin-drv = <4>;
 	};
 
 	sd0_bus8: sd0-bus-width8 {
 		samsung,pins = "gpr1-4", "gpr1-5", "gpr1-6", "gpr1-7";
 		samsung,pin-function = <2>;
 		samsung,pin-pud = <3>;
-		samsung,pin-drv = <3>;
+		samsung,pin-drv = <4>;
 	};
 
 	sd1_clk: sd1-clk {

arch/arm64/boot/dts/freescale/Makefile

+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-frdm.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-qds.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-qds.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-qds.dtb

arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts

+/*
+ * Device Tree file for Freescale LS1012A Freedom Board.
+ *
+ * Copyright 2016, Freescale Semiconductor
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "fsl-ls1012a.dtsi"
+
+/ {
+	model = "LS1012A Freedom Board";
+	compatible = "fsl,ls1012a-frdm", "fsl,ls1012a";
+
+	sys_mclk: clock-mclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,widgets =
+			"Microphone", "Microphone Jack",
+			"Headphone", "Headphone Jack",
+			"Speaker", "Speaker Ext",
+			"Line", "Line In Jack";
+		simple-audio-card,routing =
+			"MIC_IN", "Microphone Jack",
+			"Microphone Jack", "Mic Bias",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT",
+			"Speaker Ext", "LINE_OUT";
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+			frame-master;
+			bitclock-master;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&codec>;
+			frame-master;
+			bitclock-master;
+			system-clock-frequency = <25000000>;
+		};
+	};
+};
+
+&duart0 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	codec: sgtl5000@a {
+		#sound-dai-cells = <0>;
+		compatible = "fsl,sgtl5000";
+		reg = <0xa>;
+		VDDA-supply = <&reg_1p8v>;
+		VDDIO-supply = <&reg_1p8v>;
+		clocks = <&sys_mclk>;
+	};
+};
+
+&sai2 {
+	status = "okay";
+};

arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts

+/*
+ * Device Tree file for Freescale LS1012A QDS Board.
+ *
+ * Copyright 2016, Freescale Semiconductor
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "fsl-ls1012a.dtsi"
+
+/ {
+	model = "LS1012A QDS Board";
+	compatible = "fsl,ls1012a-qds", "fsl,ls1012a";
+
+	sys_mclk: clock-mclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,widgets =
+			"Microphone", "Microphone Jack",
+			"Headphone", "Headphone Jack",
+			"Speaker", "Speaker Ext",
+			"Line", "Line In Jack";
+		simple-audio-card,routing =
+			"MIC_IN", "Microphone Jack",
+			"Microphone Jack", "Mic Bias",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT",
+			"Speaker Ext", "LINE_OUT";
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+			frame-master;
+			bitclock-master;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&codec>;
+			frame-master;
+			bitclock-master;
+			system-clock-frequency = <24576000>;
+		};
+	};
+};
+
+&duart0 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	pca9547@77 {
+		compatible = "nxp,pca9547";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4>;
+
+			codec: sgtl5000@a {
+				#sound-dai-cells = <0>;
+				compatible = "fsl,sgtl5000";
+				reg = <0xa>;
+				VDDA-supply = <&reg_3p3v>;
+				VDDIO-supply = <&reg_3p3v>;
+				clocks = <&sys_mclk>;
+			};
+		};
+	};
+};
+
+&sai2 {
+	status = "okay";
+};

arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts

+/*
+ * Device Tree file for Freescale LS1012A RDB Board.
+ *
+ * Copyright 2016, Freescale Semiconductor
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "fsl-ls1012a.dtsi"
+
+/ {
+	model = "LS1012A RDB Board";
+	compatible = "fsl,ls1012a-rdb", "fsl,ls1012a";
+};
+
+&duart0 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+};

arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi

@@ -45,6 +45,7 @@
  */
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>
 
 / {
 	compatible = "fsl,ls1046a";
@@ -67,6 +68,7 @@ cpu0: cpu@0 {
 			clocks = <&clockgen 1 0>;
 			next-level-cache = <&l2>;
 			cpu-idle-states = <&CPU_PH20>;
+			#cooling-cells = <2>;
 		};
 
 		cpu1: cpu@1 {
@@ -279,6 +281,84 @@ clockgen: clocking@1ee1000 {
 			clocks = <&sysclk>;
 		};
 
+		tmu: tmu@1f00000 {
+			compatible = "fsl,qoriq-tmu";
+			reg = <0x0 0x1f00000 0x0 0x10000>;
+			interrupts = <0 33 0x4>;
+			fsl,tmu-range = <0xb0000 0x9002a 0x6004c 0x30062>;
+			fsl,tmu-calibration =
+				/* Calibration data group 1 */
+				<0x00000000 0x00000026
+				0x00000001 0x0000002d
+				0x00000002 0x00000032
+				0x00000003 0x00000039
+				0x00000004 0x0000003f
+				0x00000005 0x00000046
+				0x00000006 0x0000004d
+				0x00000007 0x00000054
+				0x00000008 0x0000005a
+				0x00000009 0x00000061
+				0x0000000a 0x0000006a
+				0x0000000b 0x00000071
+				/* Calibration data group 2 */
+				0x00010000 0x00000025
+				0x00010001 0x0000002c
+				0x00010002 0x00000035
+				0x00010003 0x0000003d
+				0x00010004 0x00000045
+				0x00010005 0x0000004e
+				0x00010006 0x00000057
+				0x00010007 0x00000061
+				0x00010008 0x0000006b
+				0x00010009 0x00000076
+				/* Calibration data group 3 */
+				0x00020000 0x00000029
+				0x00020001 0x00000033
+				0x00020002 0x0000003d
+				0x00020003 0x00000049
+				0x00020004 0x00000056
+				0x00020005 0x00000061
+				0x00020006 0x0000006d
+				/* Calibration data group 4 */
+				0x00030000 0x00000021
+				0x00030001 0x0000002a
+				0x00030002 0x0000003c
+				0x00030003 0x0000004e>;
+			big-endian;
+			#thermal-sensor-cells = <1>;
+		};
+
+		thermal-zones {
+			cpu_thermal: cpu-thermal {
+				polling-delay-passive = <1000>;
+				polling-delay = <5000>;
+				thermal-sensors = <&tmu 3>;
+
+				trips {
+					cpu_alert: cpu-alert {
+						temperature = <85000>;
+						hysteresis = <2000>;
+						type = "passive";
+					};
+
+					cpu_crit: cpu-crit {
+						temperature = <95000>;
+						hysteresis = <2000>;
+						type = "critical";
+					};
+				};
+
+				cooling-maps {
+					map0 {
+						trip = <&cpu_alert>;
+						cooling-device =
+							<&cpu0 THERMAL_NO_LIMIT
+							THERMAL_NO_LIMIT>;
+					};
+				};
+			};
+		};
+
 		dspi: dspi@2100000 {
 			compatible = "fsl,ls1021a-v1.0-dspi";
 			#address-cells = <1>;

arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts

@@ -102,7 +102,6 @@ pca9547@75 {
 		reg = <0x75>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		status = "disabled";
 		i2c@1 {
 			#address-cells = <1>;
 			#size-cells = <0>;

arch/arm64/boot/dts/hisilicon/Makefile

+dtb-$(CONFIG_ARCH_HISI) += hi3660-hikey960.dtb
 dtb-$(CONFIG_ARCH_HISI) += hi6220-hikey.dtb
 dtb-$(CONFIG_ARCH_HISI) += hip05-d02.dtb
 dtb-$(CONFIG_ARCH_HISI) += hip06-d03.dtb

arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts

+/*
+ * dts file for Hisilicon HiKey960 Development Board
+ *
+ * Copyright (C) 2016, Hisilicon Ltd.
+ *
+ */
+
+/dts-v1/;
+
+#include "hi3660.dtsi"
+
+/ {
+	model = "HiKey960";
+	compatible = "hisilicon,hi3660";
+
+	aliases {
+		serial5 = &uart5;       /* console UART */
+	};
+
+	chosen {
+		stdout-path = "serial5:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		/* rewrite this at bootloader */
+		reg = <0x0 0x0 0x0 0x0>;
+	};
+};
+
+&uart5 {
+	status = "okay";
+};

arch/arm64/boot/dts/marvell/Makefile

@@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb
 
 always		:= $(dtb-y)
 subdir-y	:= $(dts-dirs)

arch/arm64/boot/dts/marvell/armada-cp110-master.dtsi

@@ -74,13 +74,14 @@ cpm_syscon0: system-controller@440000 {
 					"cpm-gop-dp", "none", "cpm-pcie_x10",
 					"cpm-pcie_x11", "cpm-pcie_x4", "cpm-pcie-xor",
 					"cpm-sata", "cpm-sata-usb", "cpm-main",
-					"cpm-sd-mmc", "none", "none",
+					"cpm-sd-mmc-gop", "none", "none",
 					"cpm-slow-io", "cpm-usb3h0", "cpm-usb3h1",
 					"cpm-usb3dev", "cpm-eip150", "cpm-eip197";
 			};
 
 			cpm_sata0: sata@540000 {
-				compatible = "marvell,armada-8k-ahci";
+				compatible = "marvell,armada-8k-ahci",
+					     "generic-ahci";
 				reg = <0x540000 0x30000>;
 				interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&cpm_syscon0 1 15>;

arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts

@@ -277,6 +277,8 @@ &rcar_sound {
 		 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
 		 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
 		 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
 		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
 		 <&audio_clk_a>, <&cs2000>,
 		 <&audio_clk_c>,