Commit cb5a82d2 authored by Vladimir Oltean's avatar Vladimir Oltean Committed by David S. Miller

net: dsa: sja1105: properly power down the microcontroller clock for SJA1110

It turns out that powering down the BASE_TIMER_CLK does not turn off the
microcontroller, just its timers, including the one for the watchdog.
So the embedded microcontroller is still running, and potentially still
doing things.

To prevent unwanted interference, we should power down the BASE_MCSS_CLK
as well (MCSS = microcontroller subsystem).

The trouble is that currently we turn off the BASE_TIMER_CLK for SJA1110
from the .clocking_setup() method, mostly because this is a Clock
Generation Unit (CGU) setting which was traditionally configured in that
method for SJA1105. But in SJA1105, the CGU was used for bringing up the
port clocks at the proper speeds, and in SJA1110 it's not (but rather
for initial configuration), so it's best that we rebrand the
sja1110_clocking_setup() method into what it really is - an implementation
of the .disable_microcontroller() method.

Since disabling the microcontroller only needs to be done once, at probe
time, we can choose the best place to do that as being in sja1105_setup(),
before we upload the static config to the device. This guarantees that
the static config being used by the switch afterwards is really ours.

Note that the procedure to upload a static config necessarily resets the
switch. This already did not reset the microcontroller, only the switch
core, so since the .disable_microcontroller() method is guaranteed to be
called by that point, if it's disabled, it remains disabled. Add a
comment to make that clear.

With the code movement for SJA1110 from .clocking_setup() to
.disable_microcontroller(), both methods are optional and are guarded by
"if" conditions.

Tested by enabling in the device tree the rev-mii switch port 0 that
goes towards the microcontroller, and flashing a firmware that would
have networking. Without this patch, the microcontroller can be pinged,
with this patch it cannot.
Signed-off-by: default avatarVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 60ae9f88
......@@ -136,6 +136,7 @@ struct sja1105_info {
int (*clocking_setup)(struct sja1105_private *priv);
int (*pcs_mdio_read)(struct mii_bus *bus, int phy, int reg);
int (*pcs_mdio_write)(struct mii_bus *bus, int phy, int reg, u16 val);
int (*disable_microcontroller)(struct sja1105_private *priv);
const char *name;
bool supports_mii[SJA1105_MAX_NUM_PORTS];
bool supports_rmii[SJA1105_MAX_NUM_PORTS];
......@@ -363,7 +364,7 @@ int sja1105pqrs_setup_rgmii_delay(const void *ctx, int port);
int sja1110_setup_rgmii_delay(const void *ctx, int port);
int sja1105_clocking_setup_port(struct sja1105_private *priv, int port);
int sja1105_clocking_setup(struct sja1105_private *priv);
int sja1110_clocking_setup(struct sja1105_private *priv);
int sja1110_disable_microcontroller(struct sja1105_private *priv);
/* From sja1105_ethtool.c */
void sja1105_get_ethtool_stats(struct dsa_switch *ds, int port, u64 *data);
......
......@@ -6,6 +6,7 @@
#include "sja1105.h"
#define SJA1105_SIZE_CGU_CMD 4
#define SJA1110_BASE_MCSS_CLK SJA1110_CGU_ADDR(0x70)
#define SJA1110_BASE_TIMER_CLK SJA1110_CGU_ADDR(0x74)
/* Common structure for CFG_PAD_MIIx_RX and CFG_PAD_MIIx_TX */
......@@ -832,17 +833,30 @@ sja1110_cgu_outclk_packing(void *buf, struct sja1110_cgu_outclk *outclk,
sja1105_packing(buf, &outclk->pd, 0, 0, size, op);
}
/* Power down the BASE_TIMER_CLK in order to disable the watchdog */
int sja1110_clocking_setup(struct sja1105_private *priv)
int sja1110_disable_microcontroller(struct sja1105_private *priv)
{
u8 packed_buf[SJA1105_SIZE_CGU_CMD] = {0};
struct sja1110_cgu_outclk outclk_6_c = {
.clksrc = 0x3,
.pd = true,
};
struct sja1110_cgu_outclk outclk_7_c = {
.clksrc = 0x5,
.pd = true,
};
int rc;
/* Power down the BASE_TIMER_CLK to disable the watchdog timer */
sja1110_cgu_outclk_packing(packed_buf, &outclk_7_c, PACK);
return sja1105_xfer_buf(priv, SPI_WRITE, SJA1110_BASE_TIMER_CLK,
rc = sja1105_xfer_buf(priv, SPI_WRITE, SJA1110_BASE_TIMER_CLK,
packed_buf, SJA1105_SIZE_CGU_CMD);
if (rc)
return rc;
/* Power down the BASE_MCSS_CLOCK to gate the microcontroller off */
sja1110_cgu_outclk_packing(packed_buf, &outclk_6_c, PACK);
return sja1105_xfer_buf(priv, SPI_WRITE, SJA1110_BASE_MCSS_CLK,
packed_buf, SJA1105_SIZE_CGU_CMD);
}
......@@ -1922,9 +1922,11 @@ int sja1105_static_config_reload(struct sja1105_private *priv,
* For these interfaces there is no dynamic configuration
* needed, since PLLs have same settings at all speeds.
*/
if (priv->info->clocking_setup) {
rc = priv->info->clocking_setup(priv);
if (rc < 0)
goto out;
}
for (i = 0; i < ds->num_ports; i++) {
struct dw_xpcs *xpcs = priv->xpcs[i];
......@@ -3032,18 +3034,34 @@ static int sja1105_setup(struct dsa_switch *ds)
goto out_ptp_clock_unregister;
}
if (priv->info->disable_microcontroller) {
rc = priv->info->disable_microcontroller(priv);
if (rc < 0) {
dev_err(ds->dev,
"Failed to disable microcontroller: %pe\n",
ERR_PTR(rc));
goto out_mdiobus_unregister;
}
}
/* Create and send configuration down to device */
rc = sja1105_static_config_load(priv);
if (rc < 0) {
dev_err(ds->dev, "Failed to load static config: %d\n", rc);
goto out_mdiobus_unregister;
}
/* Configure the CGU (PHY link modes and speeds) */
if (priv->info->clocking_setup) {
rc = priv->info->clocking_setup(priv);
if (rc < 0) {
dev_err(ds->dev, "Failed to configure MII clocking: %d\n", rc);
dev_err(ds->dev,
"Failed to configure MII clocking: %pe\n",
ERR_PTR(rc));
goto out_static_config_free;
}
}
/* On SJA1105, VLAN filtering per se is always enabled in hardware.
* The only thing we can do to disable it is lie about what the 802.1Q
* EtherType is.
......
......@@ -199,7 +199,11 @@ static int sja1110_reset_cmd(struct dsa_switch *ds)
const struct sja1105_regs *regs = priv->info->regs;
u32 switch_reset = BIT(20);
/* Switch core reset */
/* Only reset the switch core.
* A full cold reset would re-enable the BASE_MCSS_CLOCK PLL which
* would turn on the microcontroller, potentially letting it execute
* code which could interfere with our configuration.
*/
return sja1105_xfer_u32(priv, SPI_WRITE, regs->rgu, &switch_reset, NULL);
}
......@@ -796,7 +800,7 @@ const struct sja1105_info sja1110a_info = {
.ptp_cmd_packing = sja1105pqrs_ptp_cmd_packing,
.rxtstamp = sja1110_rxtstamp,
.txtstamp = sja1110_txtstamp,
.clocking_setup = sja1110_clocking_setup,
.disable_microcontroller = sja1110_disable_microcontroller,
.pcs_mdio_read = sja1110_pcs_mdio_read,
.pcs_mdio_write = sja1110_pcs_mdio_write,
.port_speed = {
......@@ -847,7 +851,7 @@ const struct sja1105_info sja1110b_info = {
.ptp_cmd_packing = sja1105pqrs_ptp_cmd_packing,
.rxtstamp = sja1110_rxtstamp,
.txtstamp = sja1110_txtstamp,
.clocking_setup = sja1110_clocking_setup,
.disable_microcontroller = sja1110_disable_microcontroller,
.pcs_mdio_read = sja1110_pcs_mdio_read,
.pcs_mdio_write = sja1110_pcs_mdio_write,
.port_speed = {
......@@ -898,7 +902,7 @@ const struct sja1105_info sja1110c_info = {
.ptp_cmd_packing = sja1105pqrs_ptp_cmd_packing,
.rxtstamp = sja1110_rxtstamp,
.txtstamp = sja1110_txtstamp,
.clocking_setup = sja1110_clocking_setup,
.disable_microcontroller = sja1110_disable_microcontroller,
.pcs_mdio_read = sja1110_pcs_mdio_read,
.pcs_mdio_write = sja1110_pcs_mdio_write,
.port_speed = {
......@@ -949,7 +953,7 @@ const struct sja1105_info sja1110d_info = {
.ptp_cmd_packing = sja1105pqrs_ptp_cmd_packing,
.rxtstamp = sja1110_rxtstamp,
.txtstamp = sja1110_txtstamp,
.clocking_setup = sja1110_clocking_setup,
.disable_microcontroller = sja1110_disable_microcontroller,
.pcs_mdio_read = sja1110_pcs_mdio_read,
.pcs_mdio_write = sja1110_pcs_mdio_write,
.port_speed = {
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment