stmmac: code tidy-up

This patch tidies up the code. I have run Linden (and verified with checkpatch)
many part of the driver trying to reorganize some sections respecting the
codying-style rules in the points where it was not done.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/stmicro/stmmac/chain_mode.c

@@ -30,7 +30,7 @@
 
 static unsigned int stmmac_jumbo_frm(void *p, struct sk_buff *skb, int csum)
 {
-	struct stmmac_priv *priv = (struct stmmac_priv *) p;
+	struct stmmac_priv *priv = (struct stmmac_priv *)p;
 	unsigned int txsize = priv->dma_tx_size;
 	unsigned int entry = priv->cur_tx % txsize;
 	struct dma_desc *desc = priv->dma_tx + entry;
@@ -103,7 +103,7 @@ static void stmmac_init_dma_chain(void *des, dma_addr_t phy_addr,
 	dma_addr_t dma_phy = phy_addr;
 
 	if (extend_desc) {
-		struct dma_extended_desc *p = (struct dma_extended_desc *) des;
+		struct dma_extended_desc *p = (struct dma_extended_desc *)des;
 		for (i = 0; i < (size - 1); i++) {
 			dma_phy += sizeof(struct dma_extended_desc);
 			p->basic.des3 = (unsigned int)dma_phy;
@@ -112,7 +112,7 @@ static void stmmac_init_dma_chain(void *des, dma_addr_t phy_addr,
 		p->basic.des3 = (unsigned int)phy_addr;
 
 	} else {
-		struct dma_desc *p = (struct dma_desc *) des;
+		struct dma_desc *p = (struct dma_desc *)des;
 		for (i = 0; i < (size - 1); i++) {
 			dma_phy += sizeof(struct dma_desc);
 			p->des3 = (unsigned int)dma_phy;

drivers/net/ethernet/stmicro/stmmac/common.h

@@ -182,29 +182,29 @@ struct stmmac_extra_stats {
 #define DMA_HW_FEAT_HDSEL	0x00000004	/* Half-Duplex Support */
 #define DMA_HW_FEAT_EXTHASHEN	0x00000008	/* Expanded DA Hash Filter */
 #define DMA_HW_FEAT_HASHSEL	0x00000010	/* HASH Filter */
-#define DMA_HW_FEAT_ADDMACADRSEL	0x00000020 /* Multiple MAC Addr Reg */
+#define DMA_HW_FEAT_ADDMAC	0x00000020	/* Multiple MAC Addr Reg */
 #define DMA_HW_FEAT_PCSSEL	0x00000040	/* PCS registers */
 #define DMA_HW_FEAT_L3L4FLTREN	0x00000080	/* Layer 3 & Layer 4 Feature */
 #define DMA_HW_FEAT_SMASEL	0x00000100	/* SMA(MDIO) Interface */
 #define DMA_HW_FEAT_RWKSEL	0x00000200	/* PMT Remote Wakeup */
 #define DMA_HW_FEAT_MGKSEL	0x00000400	/* PMT Magic Packet */
 #define DMA_HW_FEAT_MMCSEL	0x00000800	/* RMON Module */
-#define DMA_HW_FEAT_TSVER1SEL	0x00001000 /* Only IEEE 1588-2002 Timestamp */
-#define DMA_HW_FEAT_TSVER2SEL	0x00002000 /* IEEE 1588-2008 Adv Timestamp */
+#define DMA_HW_FEAT_TSVER1SEL	0x00001000	/* Only IEEE 1588-2002 */
+#define DMA_HW_FEAT_TSVER2SEL	0x00002000	/* IEEE 1588-2008 PTPv2 */
 #define DMA_HW_FEAT_EEESEL	0x00004000	/* Energy Efficient Ethernet */
 #define DMA_HW_FEAT_AVSEL	0x00008000	/* AV Feature */
 #define DMA_HW_FEAT_TXCOESEL	0x00010000	/* Checksum Offload in Tx */
-#define DMA_HW_FEAT_RXTYP1COE	0x00020000 /* IP csum Offload(Type 1) in Rx */
-#define DMA_HW_FEAT_RXTYP2COE	0x00040000 /* IP csum Offload(Type 2) in Rx */
+#define DMA_HW_FEAT_RXTYP1COE	0x00020000	/* IP COE (Type 1) in Rx */
+#define DMA_HW_FEAT_RXTYP2COE	0x00040000	/* IP COE (Type 2) in Rx */
 #define DMA_HW_FEAT_RXFIFOSIZE	0x00080000	/* Rx FIFO > 2048 Bytes */
-#define DMA_HW_FEAT_RXCHCNT	0x00300000 /* No. of additional Rx Channels */
-#define DMA_HW_FEAT_TXCHCNT	0x00c00000 /* No. of additional Tx Channels */
-#define DMA_HW_FEAT_ENHDESSEL	0x01000000 /* Alternate (Enhanced Descriptor) */
-#define DMA_HW_FEAT_INTTSEN	0x02000000 /* Timestamping with Internal
-					      System Time */
+#define DMA_HW_FEAT_RXCHCNT	0x00300000	/* No. additional Rx Channels */
+#define DMA_HW_FEAT_TXCHCNT	0x00c00000	/* No. additional Tx Channels */
+#define DMA_HW_FEAT_ENHDESSEL	0x01000000	/* Alternate Descriptor */
+/* Timestamping with Internal System Time */
+#define DMA_HW_FEAT_INTTSEN	0x02000000
 #define DMA_HW_FEAT_FLEXIPPSEN	0x04000000	/* Flexible PPS Output */
-#define DMA_HW_FEAT_SAVLANINS	0x08000000 /* Source Addr or VLAN Insertion */
-#define DMA_HW_FEAT_ACTPHYIF	0x70000000 /* Active/selected PHY interface */
+#define DMA_HW_FEAT_SAVLANINS	0x08000000	/* Source Addr or VLAN */
+#define DMA_HW_FEAT_ACTPHYIF	0x70000000	/* Active/selected PHY iface */
 #define DEFAULT_DMA_PBL		8
 
 /* Max/Min RI Watchdog Timer count value */
@@ -216,7 +216,8 @@ struct stmmac_extra_stats {
 #define STMMAC_TX_MAX_FRAMES	256
 #define STMMAC_TX_FRAMES	64
 
-enum rx_frame_status { /* IPC status */
+/* Rx IPC status */
+enum rx_frame_status {
 	good_frame = 0,
 	discard_frame = 1,
 	csum_none = 2,
@@ -261,9 +262,9 @@ struct dma_features {
 	unsigned int pmt_remote_wake_up;
 	unsigned int pmt_magic_frame;
 	unsigned int rmon;
-	/* IEEE 1588-2002*/
+	/* IEEE 1588-2002 */
 	unsigned int time_stamp;
-	/* IEEE 1588-2008*/
+	/* IEEE 1588-2008 */
 	unsigned int atime_stamp;
 	/* 802.3az - Energy-Efficient Ethernet (EEE) */
 	unsigned int eee;
@@ -276,7 +277,7 @@ struct dma_features {
 	/* TX and RX number of channels */
 	unsigned int number_rx_channel;
 	unsigned int number_tx_channel;
-	/* Alternate (enhanced) DESC mode*/
+	/* Alternate (enhanced) DESC mode */
 	unsigned int enh_desc;
 };
 
@@ -344,7 +345,7 @@ struct stmmac_desc_ops {
 	/* get tx timestamp status */
 	int (*get_tx_timestamp_status) (struct dma_desc *p);
 	/* get timestamp value */
-	u64 (*get_timestamp) (void *desc, u32 ats);
+	 u64(*get_timestamp) (void *desc, u32 ats);
 	/* get rx timestamp status */
 	int (*get_rx_timestamp_status) (void *desc, u32 ats);
 };
@@ -378,7 +379,7 @@ struct stmmac_dma_ops {
 
 struct stmmac_ops {
 	/* MAC core initialization */
-	void (*core_init) (void __iomem *ioaddr) ____cacheline_aligned;
+	void (*core_init) (void __iomem *ioaddr);
 	/* Enable and verify that the IPC module is supported */
 	int (*rx_ipc) (void __iomem *ioaddr);
 	/* Dump MAC registers */
@@ -410,10 +411,10 @@ struct stmmac_hwtimestamp {
 	void (*config_hw_tstamping) (void __iomem *ioaddr, u32 data);
 	void (*config_sub_second_increment) (void __iomem *ioaddr);
 	int (*init_systime) (void __iomem *ioaddr, u32 sec, u32 nsec);
-	int (*config_addend)(void __iomem *ioaddr, u32 addend);
-	int (*adjust_systime)(void __iomem *ioaddr, u32 sec, u32 nsec,
+	int (*config_addend) (void __iomem *ioaddr, u32 addend);
+	int (*adjust_systime) (void __iomem *ioaddr, u32 sec, u32 nsec,
 			       int add_sub);
-	u64 (*get_systime)(void __iomem *ioaddr);
+	 u64(*get_systime) (void __iomem *ioaddr);
 };
 
 struct mac_link {

drivers/net/ethernet/stmicro/stmmac/descs_com.h

@@ -117,8 +117,7 @@ static inline void ndesc_rx_set_on_chain(struct dma_desc *p, int end)
 	p->des01.rx.second_address_chained = 1;
 }
 
-static inline void ndesc_tx_set_on_chain(struct dma_desc *p, int
-						 ring_size)
+static inline void ndesc_tx_set_on_chain(struct dma_desc *p, int ring_size)
 {
 	p->des01.tx.second_address_chained = 1;
 }

drivers/net/ethernet/stmicro/stmmac/dwmac1000.h

@@ -141,7 +141,7 @@ enum inter_frame_gap {
 	GMAC_CONTROL_IFG_80 = 0x00020000,
 	GMAC_CONTROL_IFG_40 = 0x000e0000,
 };
-#define GMAC_CONTROL_DCRS	0x00010000 /* Disable carrier sense during tx */
+#define GMAC_CONTROL_DCRS	0x00010000	/* Disable carrier sense */
 #define GMAC_CONTROL_PS		0x00008000	/* Port Select 0:GMI 1:MII */
 #define GMAC_CONTROL_FES	0x00004000	/* Speed 0:10 1:100 */
 #define GMAC_CONTROL_DO		0x00002000	/* Disable Rx Own */
@@ -150,7 +150,7 @@ enum inter_frame_gap {
 #define GMAC_CONTROL_IPC	0x00000400	/* Checksum Offload */
 #define GMAC_CONTROL_DR		0x00000200	/* Disable Retry */
 #define GMAC_CONTROL_LUD	0x00000100	/* Link up/down */
-#define GMAC_CONTROL_ACS	0x00000080 /* Automatic Pad/FCS Stripping */
+#define GMAC_CONTROL_ACS	0x00000080	/* Auto Pad/FCS Stripping */
 #define GMAC_CONTROL_DC		0x00000010	/* Deferral Check */
 #define GMAC_CONTROL_TE		0x00000008	/* Transmitter Enable */
 #define GMAC_CONTROL_RE		0x00000004	/* Receiver Enable */
@@ -191,9 +191,9 @@ enum inter_frame_gap {
 #define DMA_BUS_MODE_ATDS	0x00000080	/* Alternate Descriptor Size */
 
 enum rx_tx_priority_ratio {
-	double_ratio = 0x00004000,	/*2:1 */
-	triple_ratio = 0x00008000,	/*3:1 */
-	quadruple_ratio = 0x0000c000,	/*4:1 */
+	double_ratio = 0x00004000,	/* 2:1 */
+	triple_ratio = 0x00008000,	/* 3:1 */
+	quadruple_ratio = 0x0000c000,	/* 4:1 */
 };
 
 #define DMA_BUS_MODE_FB		0x00010000	/* Fixed burst */
@@ -213,7 +213,8 @@ enum rx_tx_priority_ratio {
 #define DMA_BUS_FB	  	  0x00010000	/* Fixed Burst */
 
 /* DMA operation mode defines (start/stop tx/rx are placed in common header)*/
-#define DMA_CONTROL_DT		0x04000000 /* Disable Drop TCP/IP csum error */
+/* Disable Drop TCP/IP csum error */
+#define DMA_CONTROL_DT		0x04000000
 #define DMA_CONTROL_RSF		0x02000000	/* Receive Store and Forward */
 #define DMA_CONTROL_DFF		0x01000000	/* Disaable flushing */
 /* Threshold for Activating the FC */
@@ -264,7 +265,5 @@ enum rtc_control {
 #define GMAC_MMC_TX_INTR   0x108
 #define GMAC_MMC_RX_CSUM_OFFLOAD   0x208
 
-
-
 extern const struct stmmac_dma_ops dwmac1000_dma_ops;
 #endif /* __DWMAC1000_H__ */

drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c

@@ -87,7 +87,7 @@ static void dwmac1000_get_umac_addr(void __iomem *ioaddr, unsigned char *addr,
 
 static void dwmac1000_set_filter(struct net_device *dev, int id)
 {
-	void __iomem *ioaddr = (void __iomem *) dev->base_addr;
+	void __iomem *ioaddr = (void __iomem *)dev->base_addr;
 	unsigned int value = 0;
 	unsigned int perfect_addr_number;
 
@@ -111,12 +111,13 @@ static void dwmac1000_set_filter(struct net_device *dev, int id)
 		memset(mc_filter, 0, sizeof(mc_filter));
 		netdev_for_each_mc_addr(ha, dev) {
 			/* The upper 6 bits of the calculated CRC are used to
-			   index the contens of the hash table */
-			int bit_nr =
-			    bitrev32(~crc32_le(~0, ha->addr, 6)) >> 26;
+			 * index the contens of the hash table
+			 */
+			int bit_nr = bitrev32(~crc32_le(~0, ha->addr, 6)) >> 26;
 			/* The most significant bit determines the register to
 			 * use (H/L) while the other 5 bits determine the bit
-			 * within the register. */
+			 * within the register.
+			 */
 			mc_filter[bit_nr >> 5] |= 1 << (bit_nr & 31);
 		}
 		writel(mc_filter[0], ioaddr + GMAC_HASH_LOW);
@@ -129,10 +130,11 @@ static void dwmac1000_set_filter(struct net_device *dev, int id)
 	else
 		perfect_addr_number = GMAC_MAX_PERFECT_ADDRESSES / 2;
 
-	/* Handle multiple unicast addresses (perfect filtering)*/
+	/* Handle multiple unicast addresses (perfect filtering) */
 	if (netdev_uc_count(dev) > perfect_addr_number)
-		/* Switch to promiscuous mode is more than 16 addrs
-		   are required */
+		/* Switch to promiscuous mode if more than 16 addrs
+		 * are required
+		 */
 		value |= GMAC_FRAME_FILTER_PR;
 	else {
 		int reg = 1;
@@ -150,8 +152,8 @@ static void dwmac1000_set_filter(struct net_device *dev, int id)
 #endif
 	writel(value, ioaddr + GMAC_FRAME_FILTER);
 
-	CHIP_DBG(KERN_INFO "\tFrame Filter reg: 0x%08x\n\tHash regs: "
-	    "HI 0x%08x, LO 0x%08x\n", readl(ioaddr + GMAC_FRAME_FILTER),
+	CHIP_DBG(KERN_INFO "\tFilter: 0x%08x\n\tHash: HI 0x%08x, LO 0x%08x\n",
+		 readl(ioaddr + GMAC_FRAME_FILTER),
 		 readl(ioaddr + GMAC_HASH_HIGH), readl(ioaddr + GMAC_HASH_LOW));
 }
 
@@ -218,8 +220,7 @@ static int dwmac1000_irq_status(void __iomem *ioaddr,
 	}
 	if (unlikely(intr_status & pmt_irq)) {
 		CHIP_DBG(KERN_INFO "GMAC: received Magic frame\n");
-		/* clear the PMT bits 5 and 6 by reading the PMT
-		 * status register. */
+		/* clear the PMT bits 5 and 6 by reading the PMT status reg */
 		readl(ioaddr + GMAC_PMT);
 		x->irq_receive_pmt_irq_n++;
 	}
@@ -270,7 +271,7 @@ static int dwmac1000_irq_status(void __iomem *ioaddr,
 				x->pcs_speed = SPEED_10;
 
 			x->pcs_link = 1;
-			pr_debug("Link is Up - %d/%s\n", (int) x->pcs_speed,
+			pr_debug("Link is Up - %d/%s\n", (int)x->pcs_speed,
 				 x->pcs_duplex ? "Full" : "Half");
 		} else {
 			x->pcs_link = 0;
@@ -287,7 +288,8 @@ static void  dwmac1000_set_eee_mode(void __iomem *ioaddr)
 
 	/* Enable the link status receive on RGMII, SGMII ore SMII
 	 * receive path and instruct the transmit to enter in LPI
-	 * state. */
+	 * state.
+	 */
 	value = readl(ioaddr + LPI_CTRL_STATUS);
 	value |= LPI_CTRL_STATUS_LPIEN | LPI_CTRL_STATUS_LPITXA;
 	writel(value, ioaddr + LPI_CTRL_STATUS);

drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c

@@ -94,14 +94,16 @@ static int dwmac1000_dma_init(void __iomem *ioaddr, int pbl, int fb, int mb,
 	 *
 	 *  For Non Fixed Burst Mode: provide the maximum value of the
 	 *  burst length. Any burst equal or below the provided burst
-	 *  length would be allowed to perform. */
+	 *  length would be allowed to perform.
+	 */
 	writel(burst_len, ioaddr + DMA_AXI_BUS_MODE);
 
 	/* Mask interrupts by writing to CSR7 */
 	writel(DMA_INTR_DEFAULT_MASK, ioaddr + DMA_INTR_ENA);
 
-	/* The base address of the RX/TX descriptor lists must be written into
-	 * DMA CSR3 and CSR4, respectively. */
+	/* RX/TX descriptor base address lists must be written into
+	 * DMA CSR3 and CSR4, respectively
+	 */
 	writel(dma_tx, ioaddr + DMA_TX_BASE_ADDR);
 	writel(dma_rx, ioaddr + DMA_RCV_BASE_ADDR);
 
@@ -118,11 +120,12 @@ static void dwmac1000_dma_operation_mode(void __iomem *ioaddr, int txmode,
 		/* Transmit COE type 2 cannot be done in cut-through mode. */
 		csr6 |= DMA_CONTROL_TSF;
 		/* Operating on second frame increase the performance
-		 * especially when transmit store-and-forward is used.*/
+		 * especially when transmit store-and-forward is used.
+		 */
 		csr6 |= DMA_CONTROL_OSF;
 	} else {
-		CHIP_DBG(KERN_DEBUG "GMAC: disabling TX store and forward mode"
-			      " (threshold = %d)\n", txmode);
+		CHIP_DBG(KERN_DEBUG "GMAC: disabling TX SF (threshold %d)\n",
+			 txmode);
 		csr6 &= ~DMA_CONTROL_TSF;
 		csr6 &= DMA_CONTROL_TC_TX_MASK;
 		/* Set the transmit threshold */
@@ -142,8 +145,8 @@ static void dwmac1000_dma_operation_mode(void __iomem *ioaddr, int txmode,
 		CHIP_DBG(KERN_DEBUG "GMAC: enable RX store and forward mode\n");
 		csr6 |= DMA_CONTROL_RSF;
 	} else {
-		CHIP_DBG(KERN_DEBUG "GMAC: disabling RX store and forward mode"
-			      " (threshold = %d)\n", rxmode);
+		CHIP_DBG(KERN_DEBUG "GMAC: disable RX SF mode (threshold %d)\n",
+			 rxmode);
 		csr6 &= ~DMA_CONTROL_RSF;
 		csr6 &= DMA_CONTROL_TC_RX_MASK;
 		if (rxmode <= 32)

drivers/net/ethernet/stmicro/stmmac/dwmac100_core.c

@@ -47,8 +47,7 @@ static void dwmac100_dump_mac_regs(void __iomem *ioaddr)
 {
 	pr_info("\t----------------------------------------------\n"
 		"\t  DWMAC 100 CSR (base addr = 0x%p)\n"
-		"\t----------------------------------------------\n",
-		ioaddr);
+		"\t----------------------------------------------\n", ioaddr);
 	pr_info("\tcontrol reg (offset 0x%x): 0x%08x\n", MAC_CONTROL,
 		readl(ioaddr + MAC_CONTROL));
 	pr_info("\taddr HI (offset 0x%x): 0x%08x\n ", MAC_ADDR_HIGH,
@@ -92,7 +91,7 @@ static void dwmac100_get_umac_addr(void __iomem *ioaddr, unsigned char *addr,
 
 static void dwmac100_set_filter(struct net_device *dev, int id)
 {
-	void __iomem *ioaddr = (void __iomem *) dev->base_addr;
+	void __iomem *ioaddr = (void __iomem *)dev->base_addr;
 	u32 value = readl(ioaddr + MAC_CONTROL);
 
 	if (dev->flags & IFF_PROMISC) {
@@ -113,7 +112,8 @@ static void dwmac100_set_filter(struct net_device *dev, int id)
 		struct netdev_hw_addr *ha;
 
 		/* Perfect filter mode for physical address and Hash
-		   filter for multicast */
+		 * filter for multicast
+		 */
 		value |= MAC_CONTROL_HP;
 		value &= ~(MAC_CONTROL_PM | MAC_CONTROL_PR |
 			   MAC_CONTROL_IF | MAC_CONTROL_HO);
@@ -121,12 +121,13 @@ static void dwmac100_set_filter(struct net_device *dev, int id)
 		memset(mc_filter, 0, sizeof(mc_filter));
 		netdev_for_each_mc_addr(ha, dev) {
 			/* The upper 6 bits of the calculated CRC are used to
-			 * index the contens of the hash table */
-			int bit_nr =
-			    ether_crc(ETH_ALEN, ha->addr) >> 26;
+			 * index the contens of the hash table
+			 */
+			int bit_nr = ether_crc(ETH_ALEN, ha->addr) >> 26;
 			/* The most significant bit determines the register to
 			 * use (H/L) while the other 5 bits determine the bit
-			 * within the register. */
+			 * within the register.
+			 */
 			mc_filter[bit_nr >> 5] |= 1 << (bit_nr & 31);
 		}
 		writel(mc_filter[0], ioaddr + MAC_HASH_LOW);
@@ -135,8 +136,7 @@ static void dwmac100_set_filter(struct net_device *dev, int id)
 
 	writel(value, ioaddr + MAC_CONTROL);
 
-	CHIP_DBG(KERN_INFO "%s: CTRL reg: 0x%08x Hash regs: "
-	    "HI 0x%08x, LO 0x%08x\n",
+	CHIP_DBG(KERN_INFO "%s: Filter: 0x%08x Hash: HI 0x%08x, LO 0x%08x\n",
 		 __func__, readl(ioaddr + MAC_CONTROL),
 		 readl(ioaddr + MAC_HASH_HIGH), readl(ioaddr + MAC_HASH_LOW));
 }
@@ -151,9 +151,7 @@ static void dwmac100_flow_ctrl(void __iomem *ioaddr, unsigned int duplex,
 	writel(flow, ioaddr + MAC_FLOW_CTRL);
 }
 
-/* No PMT module supported for this Ethernet Controller.
- * Tested on ST platforms only.
- */
+/* No PMT module supported on ST boards with this Eth chip. */
 static void dwmac100_pmt(void __iomem *ioaddr, unsigned long mode)
 {
 	return;

drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c

@@ -57,17 +57,20 @@ static int dwmac100_dma_init(void __iomem *ioaddr, int pbl, int fb, int mb,
 	/* Mask interrupts by writing to CSR7 */
 	writel(DMA_INTR_DEFAULT_MASK, ioaddr + DMA_INTR_ENA);
 
-	/* The base address of the RX/TX descriptor lists must be written into
-	 * DMA CSR3 and CSR4, respectively. */
+	/* RX/TX descriptor base addr lists must be written into
+	 * DMA CSR3 and CSR4, respectively
+	 */
 	writel(dma_tx, ioaddr + DMA_TX_BASE_ADDR);
 	writel(dma_rx, ioaddr + DMA_RCV_BASE_ADDR);
 
 	return 0;
 }
 
-/* Store and Forward capability is not used at all..
- * The transmit threshold can be programmed by
- * setting the TTC bits in the DMA control register.*/
+/* Store and Forward capability is not used at all.
+ *
+ * The transmit threshold can be programmed by setting the TTC bits in the DMA
+ * control register.
+ */
 static void dwmac100_dma_operation_mode(void __iomem *ioaddr, int txmode,
 					int rxmode)
 {
@@ -98,8 +101,7 @@ static void dwmac100_dump_dma_regs(void __iomem *ioaddr)
 		 DMA_CUR_RX_BUF_ADDR, readl(ioaddr + DMA_CUR_RX_BUF_ADDR));
 }
 
-/* DMA controller has two counters to track the number of
- * the receive missed frames. */
+/* DMA controller has two counters to track the number of the missed frames. */
 static void dwmac100_dma_diagnostic_fr(void *data, struct stmmac_extra_stats *x,
 				       void __iomem *ioaddr)
 {

drivers/net/ethernet/stmicro/stmmac/mmc.h

@@ -28,8 +28,7 @@
 /* MMC control register */
 /* When set, all counter are reset */
 #define MMC_CNTRL_COUNTER_RESET		0x1
-/* When set, do not roll over zero
- * after reaching the max value*/
+/* When set, do not roll over zero after reaching the max value*/
 #define MMC_CNTRL_COUNTER_STOP_ROLLOVER	0x2
 #define MMC_CNTRL_RESET_ON_READ		0x4	/* Reset after reading */
 #define MMC_CNTRL_COUNTER_FREEZER	0x8	/* Freeze counter values to the

drivers/net/ethernet/stmicro/stmmac/norm_desc.c

@@ -79,8 +79,8 @@ static int ndesc_get_rx_status(void *data, struct stmmac_extra_stats *x,
 	struct net_device_stats *stats = (struct net_device_stats *)data;
 
 	if (unlikely(p->des01.rx.last_descriptor == 0)) {
-		pr_warning("ndesc Error: Oversized Ethernet "
-			   "frame spanned multiple buffers\n");
+		pr_warn("%s: Oversized frame spanned multiple buffers\n",
+			__func__);
 		stats->rx_length_errors++;
 		return discard_frame;
 	}

drivers/net/ethernet/stmicro/stmmac/ring_mode.c

@@ -30,7 +30,7 @@
 
 static unsigned int stmmac_jumbo_frm(void *p, struct sk_buff *skb, int csum)
 {
-	struct stmmac_priv *priv = (struct stmmac_priv *) p;
+	struct stmmac_priv *priv = (struct stmmac_priv *)p;
 	unsigned int txsize = priv->dma_tx_size;
 	unsigned int entry = priv->cur_tx % txsize;
 	struct dma_desc *desc = priv->dma_tx + entry;

drivers/net/ethernet/stmicro/stmmac/stmmac.h

@@ -142,6 +142,7 @@ static inline int stmmac_register_platform(void)
 
 	return err;
 }
+
 static inline void stmmac_unregister_platform(void)
 {
 	platform_driver_unregister(&stmmac_pltfr_driver);
@@ -153,6 +154,7 @@ static inline int stmmac_register_platform(void)
 
 	return 0;
 }
+
 static inline void stmmac_unregister_platform(void)
 {
 }
@@ -170,6 +172,7 @@ static inline int stmmac_register_pci(void)
 
 	return err;
 }
+
 static inline void stmmac_unregister_pci(void)
 {
 	pci_unregister_driver(&stmmac_pci_driver);
@@ -181,6 +184,7 @@ static inline int stmmac_register_pci(void)
 
 	return 0;
 }
+
 static inline void stmmac_unregister_pci(void)
 {
 }

drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c

@@ -88,7 +88,7 @@ static int stmmac_pci_probe(struct pci_dev *pdev,
 			continue;
 		addr = pci_iomap(pdev, i, 0);
 		if (addr == NULL) {
-			pr_err("%s: ERROR: cannot map register memory, aborting",
+			pr_err("%s: ERROR: cannot map register memory aborting",
 			       __func__);
 			ret = -EIO;
 			goto err_out_map_failed;