Merge tag 'imx-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt

i.MX device tree changes for 5.8:

- A series from Anson Huang updating SRC devices to match bindings
  schema definition.
- Correct CPU supply name and add cpu1 supply for i.MX7D.
- Convert thermal device to use nvmem interface to get fuse data
  for imx6qdl and imx6sl.
- A series from Tim Harvey to update imx6qdl-gw devices, adding support
  of LSM9DS1 IIO imu/magn, USB OTG, bcm4330-bt, etc.
- Add input MUX for ENET2 MDIO into IMX7D pin functions.
- Misc random device addition or update.

* tag 'imx-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (22 commits)
  ARM: dts: imx53-cx9020: Group port definitions for the dvi-converter
  ARM: dts: imx5: make src node name generic
  ARM: dts: imx50: Add src node interrupt
  ARM: dts: imx: make src node name generic
  ARM: dts: imx7d-pinfunc: add input mux for ENET2 mdio
  ARM: dts: imx6sl: Use nvmem interface to get fuse data
  ARM: dts: imx6qdl: Use nvmem interface to get fuse data
  ARM: dts: imx6qdl-gw5910: fix wlan regulator
  ARM: dts: imx6qdl-gw5910: add support for bcm4330-bt
  ARM: dts: imx6qdl-gw5904: add lsm9ds1 iio imu/magn support
  ARM: dts: imx6qdl-gw560x: add lsm9ds1 iio imu/magn support
  ARM: dts: imx53: Add src node interrupt
  ARM: dts: imx51: Add src node interrupt
  ARM: dts: imx50: Remove unused iomuxc-gpr node
  ARM: dts: imx6qdl-gw552x: add USB OTG support
  ARM: dts: imx6-sr-som: add ethernet PHY configuration
  arm: dts: ls1021atwr: Add QSPI node properties
  ARM: dts: e60k02: add interrupt for PMIC
  ARM: dts: colibri: introduce device trees with UHS-I support
  ARM: dts: imx7d: Add cpu1 supply
  ...

Link: https://lore.kernel.org/r/20200523032516.11016-4-shawnguo@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

arch/arm/boot/dts/Makefile

@@ -416,6 +416,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-aristainetos2_4.dtb \
 	imx6dl-aristainetos2_7.dtb \
 	imx6dl-colibri-eval-v3.dtb \
+	imx6dl-colibri-v1_1-eval-v3.dtb \
 	imx6dl-cubox-i.dtb \
 	imx6dl-cubox-i-emmc-som-v15.dtb \
 	imx6dl-cubox-i-som-v15.dtb \

arch/arm/boot/dts/e60k02.dtsi

@@ -117,6 +117,8 @@ &i2c3 {
 	ricoh619: pmic@32 {
 		compatible = "ricoh,rc5t619";
 		reg = <0x32>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
 		system-power-controller;
 
 		regulators {

arch/arm/boot/dts/imx50.dtsi

@@ -288,11 +288,6 @@ iomuxc: iomuxc@53fa8000 {
 				reg = <0x53fa8000 0x4000>;
 			};
 
-			gpr: iomuxc-gpr@53fa8000 {
-				compatible = "fsl,imx50-iomuxc-gpr", "syscon";
-				reg = <0x53fa8000 0xc>;
-			};
-
 			pwm1: pwm@53fb4000 {
 				#pwm-cells = <2>;
 				compatible = "fsl,imx50-pwm", "fsl,imx27-pwm";
@@ -333,9 +328,10 @@ uart2: serial@53fc0000 {
 				status = "disabled";
 			};
 
-			src: src@53fd0000 {
+			src: reset-controller@53fd0000 {
 				compatible = "fsl,imx50-src", "fsl,imx51-src";
 				reg = <0x53fd0000 0x4000>;
+				interrupts = <75>;
 				#reset-cells = <1>;
 			};
 

arch/arm/boot/dts/imx51.dtsi

@@ -439,9 +439,10 @@ uart2: serial@73fc0000 {
 				status = "disabled";
 			};
 
-			src: src@73fd0000 {
+			src: reset-controller@73fd0000 {
 				compatible = "fsl,imx51-src";
 				reg = <0x73fd0000 0x4000>;
+				interrupts = <75>;
 				#reset-cells = <1>;
 			};
 

arch/arm/boot/dts/imx53-cx9020.dts

@@ -59,9 +59,11 @@ dvi_connector_in: endpoint {
 	};
 
 	dvi-converter {
+		compatible = "ti,tfp410";
+
+		ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
-		compatible = "ti,tfp410";
 
 			port@0 {
 				reg = <0>;
@@ -79,6 +81,7 @@ tfp410_out: endpoint {
 				};
 			};
 		};
+	};
 
 	leds {
 		compatible = "gpio-leds";

arch/arm/boot/dts/imx53.dtsi

@@ -588,9 +588,10 @@ can2: can@53fcc000 {
 				status = "disabled";
 			};
 
-			src: src@53fd0000 {
+			src: reset-controller@53fd0000 {
 				compatible = "fsl,imx53-src", "fsl,imx51-src";
 				reg = <0x53fd0000 0x4000>;
+				interrupts = <75>;
 				#reset-cells = <1>;
 			};
 

arch/arm/boot/dts/imx6dl-colibri-v1_1-eval-v3.dts

+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright 2020 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6dl-colibri-eval-v3.dts"
+#include "imx6qdl-colibri-v1_1-uhs.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6DL/S V1.1 on Colibri Evaluation Board V3";
+	compatible = "toradex,colibri_imx6dl-v1_1-eval-v3",
+		     "toradex,colibri_imx6dl-v1_1",
+		     "toradex,colibri_imx6dl-eval-v3",
+		     "toradex,colibri_imx6dl",
+		     "fsl,imx6dl";
+};
+
+/* Colibri MMC */
+&usdhc1 {
+	status = "okay";
+	/*
+	 * Please make sure your carrier board does not pull-up any of
+	 * the MMC/SD signals to 3.3 volt before attempting to activate
+	 * UHS-I support.
+	 * To let signaling voltage be changed to 1.8V, please
+	 * delete no-1-8-v property (example below):
+	 * /delete-property/no-1-8-v;
+	 */
+};

arch/arm/boot/dts/imx6q-dhcom-pdk2.dts

@@ -22,6 +22,53 @@ clk_ext_audio_codec: clock-codec {
 		clock-frequency = <24000000>;
 	};
 
+	display_bl: display-bl {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>;
+		default-brightness-level = <8>;
+		enable-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>;
+		status = "okay";
+	};
+
+	lcd_display: disp0 {
+		compatible = "fsl,imx-parallel-display";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interface-pix-fmt = "rgb24";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
+		status = "okay";
+
+		port@0 {
+			reg = <0>;
+
+			lcd_display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};
+
+	panel {
+		compatible = "edt,etm0700g0edh6";
+		ddc-i2c-bus = <&i2c2>;
+		backlight = <&display_bl>;
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
 	sound {
 		compatible = "fsl,imx-audio-sgtl5000";
 		model = "imx-sgtl5000";
@@ -65,6 +112,15 @@ sgtl5000: codec@a {
 		VDDA-supply = <&reg_3p3v>;
 		VDDIO-supply = <&sw2_reg>;
 	};
+
+	touchscreen@38 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touchscreen>;
+		compatible = "edt,edt-ft5406";
+		reg = <0x38>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
+	};
 };
 
 &iomuxc {
@@ -77,9 +133,7 @@ MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x400120b0
 			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x400120b0
 			MX6QDL_PAD_GPIO_5__GPIO1_IO05		0x400120b0
 			MX6QDL_PAD_CSI0_DAT17__GPIO6_IO03	0x400120b0
-			MX6QDL_PAD_GPIO_19__GPIO4_IO05		0x120b0
 			MX6QDL_PAD_DI0_PIN4__GPIO4_IO20		0x400120b0
-			MX6QDL_PAD_EIM_D27__GPIO3_IO27		0x120b0
 			MX6QDL_PAD_KEY_ROW0__GPIO4_IO07		0x120b0
 			MX6QDL_PAD_KEY_COL1__GPIO4_IO08		0x400120b0
 			MX6QDL_PAD_NANDF_CS1__GPIO6_IO14	0x400120b0
@@ -132,6 +186,52 @@ MX6QDL_PAD_EIM_D26__GPIO3_IO26		0x000b1
 		>;
 	};
 
+	pinctrl_ipu1_lcdif: ipu1-lcdif-grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x38
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x38
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x38
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x38
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x38
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x38
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x38
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x38
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x38
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x38
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x38
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x38
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x38
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x38
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x38
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x38
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x38
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x38
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x38
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x38
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x38
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x38
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x38
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x38
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x38
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x38
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x38
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x38
+			MX6QDL_PAD_EIM_D27__GPIO3_IO27			0x120b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1-grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT3__PWM1_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_touchscreen: touchscreen-grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_19__GPIO4_IO05		0x1b0b1
+		>;
+	};
+
 	pinctrl_pcie: pcie-grp {
 		fsl,pins = <
 			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20	0x1b0b1
@@ -139,6 +239,10 @@ MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20	0x1b0b1
 	};
 };
 
+&ipu1_di0_disp0 {
+	remote-endpoint = <&lcd_display_in>;
+};
+
 &pcie {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pcie>;
@@ -146,6 +250,13 @@ &pcie {
 	status = "okay";
 };
 
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	#pwm-cells = <3>;
+	status = "okay";
+};
+
 &ssi1 {
 	status = "okay";
 };

arch/arm/boot/dts/imx6qdl-colibri-v1_1-uhs.dtsi

+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright 2020 Toradex
+ */
+
+&iomuxc {
+	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x170b1
+			MX6QDL_PAD_SD1_CLK__SD1_CLK    0x100b1
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170b1
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170b1
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170b1
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170b1
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x170f1
+			MX6QDL_PAD_SD1_CLK__SD1_CLK    0x100f1
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f1
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f1
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f1
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f1
+		>;
+	};
+};
+
+/* Colibri MMC */
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_mmc_cd>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_mmc_cd>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_mmc_cd>;
+	vmmc-supply = <&reg_module_3v3>;
+	vqmmc-supply = <&vgen3_reg>;
+	wakeup-source;
+	keep-power-in-suspend;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+};

arch/arm/boot/dts/imx6qdl-colibri.dtsi

@@ -193,7 +193,16 @@ vgen2_reg: vgen2 {
 				regulator-always-on;
 			};
 
-			/* vgen3: unused */
+			/*
+			 * +V3.3_1.8_SD1 coming off VGEN3 and supplying
+			 * the i.MX 6 NVCC_SD1.
+			 */
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
 
 			vgen4_reg: vgen4 {
 				regulator-min-microvolt = <1800000>;

arch/arm/boot/dts/imx6qdl-gw552x.dtsi

@@ -258,6 +258,14 @@ &usbh1 {
 	status = "okay";
 };
 
+&usbotg {
+	vbus-supply = <&reg_5p0v>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	status = "okay";
+};
+
 &wdog1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_wdog>;
@@ -359,6 +367,12 @@ MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA	0x1b0b1
 		>;
 	};
 
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x13059
+		>;
+	};
+
 	pinctrl_wdog: wdoggrp {
 		fsl,pins = <
 			MX6QDL_PAD_DISP0_DAT8__WDOG1_B		0x1b0b0

arch/arm/boot/dts/imx6qdl-gw560x.dtsi

@@ -295,6 +295,15 @@ sgtl5000: codec@a {
 		VDDIO-supply = <&reg_3p3v>;
 	};
 
+	magn@1c {
+		compatible = "st,lsm9ds1-magn";
+		reg = <0x1c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_mag>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <9 IRQ_TYPE_EDGE_RISING>;
+	};
+
 	tca8418: keypad@34 {
 		compatible = "ti,tca8418";
 		pinctrl-names = "default";
@@ -389,6 +398,16 @@ reg_3p0v: ldo4 {
 			};
 		};
 	};
+
+	imu@6a {
+		compatible = "st,lsm9ds1-imu";
+		reg = <0x6a>;
+		st,drdy-int-pin = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_imu>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <6 IRQ_TYPE_LEVEL_HIGH>;
+	};
 };
 
 &i2c3 {
@@ -609,6 +628,12 @@ MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13	0x0001b0b0 /* LVDS_BACKEN */
 		>;
 	};
 
+	pinctrl_imu: imugrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT12__GPIO5_IO06	0x1b0b0
+		>;
+	};
+
 	pinctrl_keypad: keypadgrp {
 		fsl,pins = <
 			MX6QDL_PAD_DISP0_DAT17__GPIO5_IO11	0x0001b0b0 /* KEYPAD_IRQ# */
@@ -616,6 +641,12 @@ MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30	0x0001b0b0 /* KEYPAD_LED_EN */
 		>;
 	};
 
+	pinctrl_mag: maggrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09	0x1b0b0
+		>;
+	};
+
 	pinctrl_pcie: pciegrp {
 		fsl,pins = <
 			MX6QDL_PAD_DISP0_DAT10__GPIO4_IO31	0x1b0b0    /* PCI_RST# */

arch/arm/boot/dts/imx6qdl-gw5904.dtsi

@@ -248,6 +248,15 @@ &i2c2 {
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
+	magn@1c {
+		compatible = "st,lsm9ds1-magn";
+		reg = <0x1c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_mag>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <17 IRQ_TYPE_EDGE_RISING>;
+	};
+
 	ltc3676: pmic@3c {
 		compatible = "lltc,ltc3676";
 		reg = <0x3c>;
@@ -320,6 +329,16 @@ reg_3p0v: ldo4 {
 			};
 		};
 	};
+
+	imu@6a {
+		compatible = "st,lsm9ds1-imu";
+		reg = <0x6a>;
+		st,drdy-int-pin = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_imu>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <18 IRQ_TYPE_LEVEL_HIGH>;
+	};
 };
 
 &i2c3 {
@@ -501,6 +520,18 @@ MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
 		>;
 	};
 
+	pinctrl_imu: imugrp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_PIN2__GPIO4_IO18		0x1b0b0
+		>;
+	};
+
+	pinctrl_mag: maggrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17	0x1b0b0
+		>;
+	};
+
 	pinctrl_pcie: pciegrp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_0__GPIO1_IO00	0x1b0b0 /* PCIE RST */

arch/arm/boot/dts/imx6qdl-gw5910.dtsi

@@ -81,20 +81,6 @@ reg_wl: regulator-wl {
 		enable-active-high;
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
-	reg_bt: regulator-bt {
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_reg_bt>;
-		compatible = "regulator-fixed";
-		regulator-name = "bt";
-		gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
-		startup-delay-us = <100>;
-		enable-active-high;
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
 	};
 };
 
@@ -231,9 +217,14 @@ &uart3 {
 /* Sterling-LWB Bluetooth */
 &uart4 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart4>;
+	pinctrl-0 = <&pinctrl_uart4>,<&pinctrl_bten>;
 	uart-has-rtscts;
 	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm4330-bt";
+		shutdown-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+	};
 };
 
 /* GPS */
@@ -259,7 +250,7 @@ &usbh1 {
 &usdhc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc2>;
-	vmmc-supply = <&reg_3p3v>;
+	vmmc-supply = <&reg_wl>;
 	non-removable;
 	bus-width = <4>;
 	status = "okay";
@@ -288,6 +279,12 @@ MX6QDL_PAD_GPIO_18__GPIO7_IO13		0x1b0b1
 		>;
 	};
 
+	pinctrl_bten: btengrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b1
+		>;
+	};
+
 	pinctrl_ecspi3: escpi3grp {
 		fsl,pins = <
 			MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
@@ -393,12 +390,6 @@ MX6QDL_PAD_SD1_DAT1__PWM3_OUT		0x1b0b1
 		>;
 	};
 
-	pinctrl_reg_bt: regbtgrp {
-		fsl,pins = <
-			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b1
-		>;
-	};
-
 	pinctrl_reg_wl: regwlgrp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_5__GPIO1_IO05		0x1b0b1

arch/arm/boot/dts/imx6qdl-sr-som.dtsi

@@ -53,10 +53,21 @@ vcc_3v3: regulator-vcc-3v3 {
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
+	phy-handle = <&phy>;
 	phy-mode = "rgmii-id";
 	phy-reset-duration = <2>;
 	phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
 	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy: ethernet-phy@0 {
+			reg = <0>;
+			qca,clk-out-frequency = <125000000>;
+		};
+	};
 };
 
 &iomuxc {

arch/arm/boot/dts/imx6qdl.dtsi

@@ -74,7 +74,8 @@ tempmon: tempmon {
 		interrupt-parent = <&gpc>;
 		interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>;
 		fsl,tempmon = <&anatop>;
-		fsl,tempmon-data = <&ocotp>;
+		nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
+		nvmem-cell-names = "calib", "temp_grade";
 		clocks = <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
 		#thermal-sensor-cells = <0>;
 	};
@@ -857,7 +858,7 @@ epit2: epit@20d4000 { /* EPIT2 */
 				interrupts = <0 57 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			src: src@20d8000 {
+			src: reset-controller@20d8000 {
 				compatible = "fsl,imx6q-src", "fsl,imx51-src";
 				reg = <0x020d8000 0x4000>;
 				interrupts = <0 91 IRQ_TYPE_LEVEL_HIGH>,
@@ -1171,6 +1172,14 @@ ocotp: ocotp-ctrl@21bc000 {
 				cpu_speed_grade: speed-grade@10 {
 					reg = <0x10 4>;
 				};
+
+				tempmon_calib: calib@38 {
+					reg = <0x38 4>;
+				};
+
+				tempmon_temp_grade: temp-grade@20 {
+					reg = <0x20 4>;
+				};
 			};
 
 			tzasc@21d0000 { /* TZASC1 */

arch/arm/boot/dts/imx6sl.dtsi

@@ -98,7 +98,8 @@ tempmon: tempmon {
 		interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-parent = <&gpc>;
 		fsl,tempmon = <&anatop>;
-		fsl,tempmon-data = <&ocotp>;
+		nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
+		nvmem-cell-names = "calib", "temp_grade";
 		clocks = <&clks IMX6SL_CLK_PLL3_USB_OTG>;
 	};
 
@@ -677,7 +678,7 @@ epit2: epit@20d4000 {
 				interrupts = <0 57 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			src: src@20d8000 {
+			src: reset-controller@20d8000 {
 				compatible = "fsl,imx6sl-src", "fsl,imx51-src";
 				reg = <0x020d8000 0x4000>;
 				interrupts = <0 91 IRQ_TYPE_LEVEL_HIGH>,
@@ -961,6 +962,14 @@ ocotp: ocotp-ctrl@21bc000 {
 				cpu_speed_grade: speed-grade@10 {
 					reg = <0x10 4>;
 				};
+
+				tempmon_calib: calib@38 {
+					reg = <0x38 4>;
+				};
+
+				tempmon_temp_grade: temp-grade@20 {
+					reg = <0x20 4>;
+				};
 			};
 
 			audmux: audmux@21d8000 {

arch/arm/boot/dts/imx6sx.dtsi

@@ -754,7 +754,7 @@ epit2: epit@20d4000 {
 				interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			src: src@20d8000 {
+			src: reset-controller@20d8000 {
 				compatible = "fsl,imx6sx-src", "fsl,imx51-src";
 				reg = <0x020d8000 0x4000>;
 				interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,

arch/arm/boot/dts/imx6ul.dtsi

@@ -676,7 +676,7 @@ epit2: epit@20d4000 {
 				interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			src: src@20d8000 {
+			src: reset-controller@20d8000 {
 				compatible = "fsl,imx6ul-src", "fsl,imx51-src";
 				reg = <0x020d8000 0x4000>;
 				interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,

arch/arm/boot/dts/imx7-tqma7.dtsi

@@ -16,7 +16,7 @@ memory@80000000 {
 };
 
 &cpu0 {
-	arm-supply = <&sw1a_reg>;
+	cpu-supply = <&sw1a_reg>;
 };
 
 &i2c1 {

arch/arm/boot/dts/imx7d-cl-som-imx7.dts

@@ -37,6 +37,10 @@ &cpu0 {
 	cpu-supply = <&sw1a_reg>;
 };
 
+&cpu1 {
+	cpu-supply = <&sw1a_reg>;
+};
+
 &fec1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet1>;

arch/arm/boot/dts/imx7d-colibri.dtsi

@@ -13,6 +13,10 @@ memory@80000000 {
 	};
 };
 
+&cpu1 {
+	cpu-supply = <&reg_DCDC2>;
+};
+
 &gpmi {
 	status = "okay";
 };

arch/arm/boot/dts/imx7d-nitrogen7.dts

@@ -121,6 +121,10 @@ &cpu0 {
 	cpu-supply = <&sw1a_reg>;
 };
 
+&cpu1 {
+	cpu-supply = <&sw1a_reg>;
+};
+
 &fec1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet1>;

arch/arm/boot/dts/imx7d-pinfunc.h

@@ -592,7 +592,7 @@
 #define MX7D_PAD_UART2_RX_DATA__ECSPI1_SS3                        0x0130 0x03A0 0x0000 0x3 0x0
 #define MX7D_PAD_UART2_RX_DATA__ENET2_1588_EVENT1_IN              0x0130 0x03A0 0x0000 0x4 0x0
 #define MX7D_PAD_UART2_RX_DATA__GPIO4_IO2                         0x0130 0x03A0 0x0000 0x5 0x0
-#define MX7D_PAD_UART2_RX_DATA__ENET2_MDIO                        0x0130 0x03A0 0x0000 0x6 0x0
+#define MX7D_PAD_UART2_RX_DATA__ENET2_MDIO                        0x0130 0x03A0 0x0574 0x6 0x1
 #define MX7D_PAD_UART2_TX_DATA__UART2_DCE_TX                      0x0134 0x03A4 0x0000 0x0 0x0
 #define MX7D_PAD_UART2_TX_DATA__UART2_DTE_RX                      0x0134 0x03A4 0x06FC 0x0 0x3
 #define MX7D_PAD_UART2_TX_DATA__I2C2_SDA                          0x0134 0x03A4 0x05E0 0x1 0x0

arch/arm/boot/dts/imx7d-sdb.dts

@@ -162,6 +162,10 @@ &cpu0 {
 	cpu-supply = <&sw1a_reg>;
 };
 
+&cpu1 {
+	cpu-supply = <&sw1a_reg>;
+};
+
 &ecspi3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi3>;

arch/arm/boot/dts/imx7d-tqma7.dtsi

@@ -9,3 +9,7 @@
 
 #include "imx7d.dtsi"
 #include "imx7-tqma7.dtsi"
+
+&cpu1 {
+	cpu-supply = <&sw1a_reg>;
+};

arch/arm/boot/dts/imx7d-zii-rmu2.dts

@@ -33,7 +33,7 @@ debug {
 };
 
 &cpu0 {
-	arm-supply = <&sw1a_reg>;
+	cpu-supply = <&sw1a_reg>;
 };
 
 &ecspi1 {

arch/arm/boot/dts/imx7d-zii-rpu2.dts

@@ -182,7 +182,7 @@ &adc2 {
 };
 
 &cpu0 {
-	arm-supply = <&sw1a_reg>;
+	cpu-supply = <&sw1a_reg>;
 };
 
 &clks {

arch/arm/boot/dts/imx7s.dtsi

@@ -624,7 +624,7 @@ clks: clock-controller@30380000 {
 				clock-names = "ckil", "osc";
 			};
 
-			src: src@30390000 {
+			src: reset-controller@30390000 {
 				compatible = "fsl,imx7d-src", "syscon";
 				reg = <0x30390000 0x10000>;
 				interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/boot/dts/ls1021a-twr.dts

@@ -242,6 +242,20 @@ &esdhc {
         status = "okay";
 };
 
+&qspi {
+	status = "okay";
+
+	n25q128a130: flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <50000000>;
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
+	};
+};
+
 &sai1 {
 	status = "okay";
 };