Commit dc9b6055 authored by Peter Ujfalusi's avatar Peter Ujfalusi Committed by Vinod Koul

ARM/dmaengine: edma: Move of_dma_controller_register to the dmaengine driver

If the of_dma_controller is registered in the non dmaengine driver we could
have race condition:
the of_dma_controller has been registered, but the dmaengine driver is not
yet probed. Drivers requesting DMA channels during this window will fail
since we do not yet have dmaengine drivers registered.
Signed-off-by: default avatarPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: default avatarVinod Koul <vinod.koul@intel.com>
parent d4cb7f40
...@@ -29,7 +29,6 @@ ...@@ -29,7 +29,6 @@
#include <linux/dma-mapping.h> #include <linux/dma-mapping.h>
#include <linux/of_address.h> #include <linux/of_address.h>
#include <linux/of_device.h> #include <linux/of_device.h>
#include <linux/of_dma.h>
#include <linux/of_irq.h> #include <linux/of_irq.h>
#include <linux/pm_runtime.h> #include <linux/pm_runtime.h>
...@@ -1191,10 +1190,6 @@ static int edma_of_parse_dt(struct device *dev, ...@@ -1191,10 +1190,6 @@ static int edma_of_parse_dt(struct device *dev,
return ret; return ret;
} }
static struct of_dma_filter_info edma_filter_info = {
.filter_fn = edma_filter_fn,
};
static struct edma_soc_info *edma_setup_info_from_dt(struct device *dev, static struct edma_soc_info *edma_setup_info_from_dt(struct device *dev,
struct device_node *node) struct device_node *node)
{ {
...@@ -1209,11 +1204,6 @@ static struct edma_soc_info *edma_setup_info_from_dt(struct device *dev, ...@@ -1209,11 +1204,6 @@ static struct edma_soc_info *edma_setup_info_from_dt(struct device *dev,
if (ret) if (ret)
return ERR_PTR(ret); return ERR_PTR(ret);
dma_cap_set(DMA_SLAVE, edma_filter_info.dma_cap);
dma_cap_set(DMA_CYCLIC, edma_filter_info.dma_cap);
of_dma_controller_register(dev->of_node, of_dma_simple_xlate,
&edma_filter_info);
return info; return info;
} }
#else #else
......
...@@ -25,6 +25,7 @@ ...@@ -25,6 +25,7 @@
#include <linux/slab.h> #include <linux/slab.h>
#include <linux/spinlock.h> #include <linux/spinlock.h>
#include <linux/of.h> #include <linux/of.h>
#include <linux/of_dma.h>
#include <linux/platform_data/edma.h> #include <linux/platform_data/edma.h>
...@@ -987,9 +988,14 @@ static void edma_dma_init(struct edma_cc *ecc, struct dma_device *dma, ...@@ -987,9 +988,14 @@ static void edma_dma_init(struct edma_cc *ecc, struct dma_device *dma,
INIT_LIST_HEAD(&dma->channels); INIT_LIST_HEAD(&dma->channels);
} }
static struct of_dma_filter_info edma_filter_info = {
.filter_fn = edma_filter_fn,
};
static int edma_probe(struct platform_device *pdev) static int edma_probe(struct platform_device *pdev)
{ {
struct edma_cc *ecc; struct edma_cc *ecc;
struct device_node *parent_node = pdev->dev.parent->of_node;
int ret; int ret;
ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32)); ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
...@@ -1024,6 +1030,13 @@ static int edma_probe(struct platform_device *pdev) ...@@ -1024,6 +1030,13 @@ static int edma_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, ecc); platform_set_drvdata(pdev, ecc);
if (parent_node) {
dma_cap_set(DMA_SLAVE, edma_filter_info.dma_cap);
dma_cap_set(DMA_CYCLIC, edma_filter_info.dma_cap);
of_dma_controller_register(parent_node, of_dma_simple_xlate,
&edma_filter_info);
}
dev_info(&pdev->dev, "TI EDMA DMA engine driver\n"); dev_info(&pdev->dev, "TI EDMA DMA engine driver\n");
return 0; return 0;
...@@ -1037,7 +1050,10 @@ static int edma_remove(struct platform_device *pdev) ...@@ -1037,7 +1050,10 @@ static int edma_remove(struct platform_device *pdev)
{ {
struct device *dev = &pdev->dev; struct device *dev = &pdev->dev;
struct edma_cc *ecc = dev_get_drvdata(dev); struct edma_cc *ecc = dev_get_drvdata(dev);
struct device_node *parent_node = pdev->dev.parent->of_node;
if (parent_node)
of_dma_controller_free(parent_node);
dma_async_device_unregister(&ecc->dma_slave); dma_async_device_unregister(&ecc->dma_slave);
edma_free_slot(ecc->dummy_slot); edma_free_slot(ecc->dummy_slot);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment