Merge tag 'iio-fixes-for-4.0d' of...

Merge tag 'iio-fixes-for-4.0d' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus

Jonathan writes:

IIO fixes for 4.0 set 4

A couple more IIO fixes.

* Fix check for HAS_IOMEM in the cc100001_adc driver to avoid build errors.
  Rather curiously it was ORed with Regulator and clock support.
* vf610 driver was trying to use an ADC clock outside the possible
  spec on some boards.  The driver assumed a fixed clock speed previously
  across all boards, but that is not true.  This fix ensures that the
  reported frequency is correct on all boards.
* The adis imu common code directly set the current trigger to the
  driver supplied one.  Unfortunately this didn't increase the use count
  leading to a double free via a particular path of changing the trigger
  then removing the driver.

drivers/iio/adc/Kconfig

@@ -137,7 +137,8 @@ config AXP288_ADC
 
 config CC10001_ADC
 	tristate "Cosmic Circuits 10001 ADC driver"
-	depends on HAS_IOMEM || HAVE_CLK || REGULATOR
+	depends on HAVE_CLK || REGULATOR
+	depends on HAS_IOMEM
 	select IIO_BUFFER
 	select IIO_TRIGGERED_BUFFER
 	help

drivers/iio/adc/vf610_adc.c

@@ -141,9 +141,13 @@ struct vf610_adc {
 	struct regulator *vref;
 	struct vf610_adc_feature adc_feature;
 
+	u32 sample_freq_avail[5];
+
 	struct completion completion;
 };
 
+static const u32 vf610_hw_avgs[] = { 1, 4, 8, 16, 32 };
+
 #define VF610_ADC_CHAN(_idx, _chan_type) {			\
 	.type = (_chan_type),					\
 	.indexed = 1,						\
@@ -180,35 +184,47 @@ static const struct iio_chan_spec vf610_adc_iio_channels[] = {
 	/* sentinel */
 };
 
-/*
- * ADC sample frequency, unit is ADCK cycles.
- * ADC clk source is ipg clock, which is the same as bus clock.
+static inline void vf610_adc_calculate_rates(struct vf610_adc *info)
+{
+	unsigned long adck_rate, ipg_rate = clk_get_rate(info->clk);
+	int i;
+
+	/*
+	 * Calculate ADC sample frequencies
+	 * Sample time unit is ADCK cycles. ADCK clk source is ipg clock,
+	 * which is the same as bus clock.
 	 *
 	 * ADC conversion time = SFCAdder + AverageNum x (BCT + LSTAdder)
 	 * SFCAdder: fixed to 6 ADCK cycles
 	 * AverageNum: 1, 4, 8, 16, 32 samples for hardware average.
 	 * BCT (Base Conversion Time): fixed to 25 ADCK cycles for 12 bit mode
 	 * LSTAdder(Long Sample Time): fixed to 3 ADCK cycles
- *
- * By default, enable 12 bit resolution mode, clock source
- * set to ipg clock, So get below frequency group:
 	 */
-static const u32 vf610_sample_freq_avail[5] =
-{1941176, 559332, 286957, 145374, 73171};
+	adck_rate = ipg_rate / info->adc_feature.clk_div;
+	for (i = 0; i < ARRAY_SIZE(vf610_hw_avgs); i++)
+		info->sample_freq_avail[i] =
+			adck_rate / (6 + vf610_hw_avgs[i] * (25 + 3));
+}
 
 static inline void vf610_adc_cfg_init(struct vf610_adc *info)
 {
+	struct vf610_adc_feature *adc_feature = &info->adc_feature;
+
 	/* set default Configuration for ADC controller */
-	info->adc_feature.clk_sel = VF610_ADCIOC_BUSCLK_SET;
-	info->adc_feature.vol_ref = VF610_ADCIOC_VR_VREF_SET;
+	adc_feature->clk_sel = VF610_ADCIOC_BUSCLK_SET;
+	adc_feature->vol_ref = VF610_ADCIOC_VR_VREF_SET;
+
+	adc_feature->calibration = true;
+	adc_feature->ovwren = true;
+
+	adc_feature->res_mode = 12;
+	adc_feature->sample_rate = 1;
+	adc_feature->lpm = true;
 
-	info->adc_feature.calibration = true;
-	info->adc_feature.ovwren = true;
+	/* Use a save ADCK which is below 20MHz on all devices */
+	adc_feature->clk_div = 8;
 
-	info->adc_feature.clk_div = 1;
-	info->adc_feature.res_mode = 12;
-	info->adc_feature.sample_rate = 1;
-	info->adc_feature.lpm = true;
+	vf610_adc_calculate_rates(info);
 }
 
 static void vf610_adc_cfg_post_set(struct vf610_adc *info)
@@ -290,12 +306,10 @@ static void vf610_adc_cfg_set(struct vf610_adc *info)
 
 	cfg_data = readl(info->regs + VF610_REG_ADC_CFG);
 
-	/* low power configuration */
 	cfg_data &= ~VF610_ADC_ADLPC_EN;
 	if (adc_feature->lpm)
 		cfg_data |= VF610_ADC_ADLPC_EN;
 
-	/* disable high speed */
 	cfg_data &= ~VF610_ADC_ADHSC_EN;
 
 	writel(cfg_data, info->regs + VF610_REG_ADC_CFG);
@@ -435,10 +449,27 @@ static irqreturn_t vf610_adc_isr(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
-static IIO_CONST_ATTR_SAMP_FREQ_AVAIL("1941176, 559332, 286957, 145374, 73171");
+static ssize_t vf610_show_samp_freq_avail(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	struct vf610_adc *info = iio_priv(dev_to_iio_dev(dev));
+	size_t len = 0;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(info->sample_freq_avail); i++)
+		len += scnprintf(buf + len, PAGE_SIZE - len,
+			"%u ", info->sample_freq_avail[i]);
+
+	/* replace trailing space by newline */
+	buf[len - 1] = '\n';
+
+	return len;
+}
+
+static IIO_DEV_ATTR_SAMP_FREQ_AVAIL(vf610_show_samp_freq_avail);
 
 static struct attribute *vf610_attributes[] = {
-	&iio_const_attr_sampling_frequency_available.dev_attr.attr,
+	&iio_dev_attr_sampling_frequency_available.dev_attr.attr,
 	NULL
 };
 
@@ -502,7 +533,7 @@ static int vf610_read_raw(struct iio_dev *indio_dev,
 		return IIO_VAL_FRACTIONAL_LOG2;
 
 	case IIO_CHAN_INFO_SAMP_FREQ:
-		*val = vf610_sample_freq_avail[info->adc_feature.sample_rate];
+		*val = info->sample_freq_avail[info->adc_feature.sample_rate];
 		*val2 = 0;
 		return IIO_VAL_INT;
 
@@ -525,9 +556,9 @@ static int vf610_write_raw(struct iio_dev *indio_dev,
 	switch (mask) {
 		case IIO_CHAN_INFO_SAMP_FREQ:
 			for (i = 0;
-				i < ARRAY_SIZE(vf610_sample_freq_avail);
+				i < ARRAY_SIZE(info->sample_freq_avail);
 				i++)
-				if (val == vf610_sample_freq_avail[i]) {
+				if (val == info->sample_freq_avail[i]) {
 					info->adc_feature.sample_rate = i;
 					vf610_adc_sample_set(info);
 					return 0;

drivers/iio/imu/adis_trigger.c

@@ -60,7 +60,7 @@ int adis_probe_trigger(struct adis *adis, struct iio_dev *indio_dev)
 	iio_trigger_set_drvdata(adis->trig, adis);
 	ret = iio_trigger_register(adis->trig);
 
-	indio_dev->trig = adis->trig;
+	indio_dev->trig = iio_trigger_get(adis->trig);
 	if (ret)
 		goto error_free_irq;