Merge tag 'mvebu-dt-3.14-5' of git://git.infradead.org/linux-mvebu into next/dt

From Jason Cooper:
mvebu DT changes for v3.14 (incremental #5)

 - mvebu
    - add rtc chip isl12057 node to ReadyNAS boards
    - fix register length in Armada XP pmsu

 - kirkwood
    - sort ocp nodes by address in 6282 dtsi file
    - add 6192 dtsi file
    - add LaPlug board
    - add sata phy node

 - dove
    - add sata phy node

* tag 'mvebu-dt-3.14-5' of git://git.infradead.org/linux-mvebu:
  ARM: Kirkwood: DT board setup for LaPlug
  ARM: Kirkwood: Add 6192 DTSI file
  ARM: mvebu: fix register length for Armada XP PMSU
  ARM: kirkwood: 6282: sort DT nodes by address
  Phy: Add DT nodes on kirkwood and Dove for the SATA PHY
  ARM: mvebu: Enable ISL12057 RTC chip in ReadyNAS 2120 .dts file
  ARM: mvebu: Enable ISL12057 RTC chip in ReadyNAS 104 .dts file
  ARM: mvebu: Enable ISL12057 RTC chip in ReadyNAS 102 .dts file
Signed-off-by: Olof Johansson <olof@lixom.net>

arch/arm/boot/dts/Makefile

@@ -88,6 +88,7 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \
 	kirkwood-iomega_ix2_200.dtb \
 	kirkwood-is2.dtb \
 	kirkwood-km_kirkwood.dtb \
+	kirkwood-laplug.dtb \
 	kirkwood-lschlv2.dtb \
 	kirkwood-lsxhl.dtb \
 	kirkwood-mplcec4.dtb \

arch/arm/boot/dts/armada-370-netgear-rn102.dts

@@ -122,6 +122,11 @@ i2c@11000 {
 				clock-frequency = <100000>;
 				status = "okay";
 
+				isl12057: isl12057@68 {
+					compatible = "isl,isl12057";
+					reg = <0x68>;
+				};
+
 				g762: g762@3e {
 					compatible = "gmt,g762";
 					reg = <0x3e>;

arch/arm/boot/dts/armada-370-netgear-rn104.dts

@@ -117,6 +117,11 @@ i2c@11000 {
 				clock-frequency = <100000>;
 				status = "okay";
 
+				isl12057: isl12057@68 {
+					compatible = "isl,isl12057";
+					reg = <0x68>;
+				};
+
 				g762: g762@3e {
 					compatible = "gmt,g762";
 					reg = <0x3e>;

arch/arm/boot/dts/armada-xp-netgear-rn2120.dts

@@ -174,6 +174,11 @@ i2c@11000 {
 				clock-frequency = <400000>;
 				status = "okay";
 
+				isl12057: isl12057@68 {
+					compatible = "isl,isl12057";
+					reg = <0x68>;
+				};
+
 				/* Controller for rear fan #1 of 3 (Protechnic
 				 * MGT4012XB-O20, 8000RPM) near eSATA port */
 				g762_fan1: g762@3e {

arch/arm/boot/dts/armada-xp.dtsi

@@ -113,7 +113,7 @@ timer@20300 {
 
 			armada-370-xp-pmsu@22000 {
 				compatible = "marvell,armada-370-xp-pmsu";
-				reg = <0x22100 0x430>, <0x20800 0x20>;
+				reg = <0x22100 0x400>, <0x20800 0x20>;
 			};
 
 			eth2: ethernet@30000 {

arch/arm/boot/dts/dove.dtsi

@@ -336,10 +336,21 @@ sata0: sata-host@a0000 {
 				reg = <0xa0000 0x2400>;
 				interrupts = <62>;
 				clocks = <&gate_clk 3>;
+				phys = <&sata_phy0>;
+				phy-names = "port0";
 				nr-ports = <1>;
 				status = "disabled";
 			};
 
+			sata_phy0: sata-phy@a2000 {
+				compatible = "marvell,mvebu-sata-phy";
+				reg = <0xa2000 0x0334>;
+				clocks = <&gate_clk 3>;
+				clock-names = "sata";
+				#phy-cells = <0>;
+				status = "ok";
+			};
+
 			audio0: audio-controller@b0000 {
 				compatible = "marvell,dove-audio";
 				reg = <0xb0000 0x2210>;

arch/arm/boot/dts/kirkwood-6192.dtsi

+/ {
+	mbus {
+		pcie-controller {
+			compatible = "marvell,kirkwood-pcie";
+			status = "disabled";
+			device_type = "pci";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			bus-range = <0x00 0xff>;
+
+			ranges =
+			       <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+				0x82000000 0x1 0     MBUS_ID(0x04, 0xe8) 0       1 0 /* Port 0.0 MEM */
+				0x81000000 0x1 0     MBUS_ID(0x04, 0xe0) 0       1 0 /* Port 0.0 IO  */>;
+
+			pcie@1,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x00040000 0 0x2000>;
+				reg = <0x0800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &intc 9>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gate_clk 2>;
+				status = "disabled";
+			};
+		};
+	};
+
+	ocp@f1000000 {
+		pinctrl: pinctrl@10000 {
+			compatible = "marvell,88f6192-pinctrl";
+			reg = <0x10000 0x20>;
+
+			pmx_nand: pmx-nand {
+				marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3",
+					       "mpp4", "mpp5", "mpp18",
+					       "mpp19";
+				marvell,function = "nand";
+			};
+			pmx_sata0: pmx-sata0 {
+				marvell,pins = "mpp5", "mpp21", "mpp23";
+				marvell,function = "sata0";
+			};
+			pmx_sata1: pmx-sata1 {
+				marvell,pins = "mpp4", "mpp20", "mpp22";
+				marvell,function = "sata1";
+			};
+			pmx_spi: pmx-spi {
+				marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3";
+				marvell,function = "spi";
+			};
+			pmx_twsi0: pmx-twsi0 {
+				marvell,pins = "mpp8", "mpp9";
+				marvell,function = "twsi0";
+			};
+			pmx_uart0: pmx-uart0 {
+				marvell,pins = "mpp10", "mpp11";
+				marvell,function = "uart0";
+			};
+			pmx_uart1: pmx-uart1 {
+				marvell,pins = "mpp13", "mpp14";
+				marvell,function = "uart1";
+			};
+			pmx_sdio: pmx-sdio {
+				marvell,pins = "mpp12", "mpp13", "mpp14",
+					       "mpp15", "mpp16", "mpp17";
+				marvell,function = "sdio";
+			};
+		};
+
+		rtc@10300 {
+			compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc";
+			reg = <0x10300 0x20>;
+			interrupts = <53>;
+			clocks = <&gate_clk 7>;
+		};
+
+		sata@80000 {
+			compatible = "marvell,orion-sata";
+			reg = <0x80000 0x5000>;
+			interrupts = <21>;
+			clocks = <&gate_clk 14>, <&gate_clk 15>;
+			clock-names = "0", "1";
+			status = "disabled";
+		};
+
+		mvsdio@90000 {
+			compatible = "marvell,orion-sdio";
+			reg = <0x90000 0x200>;
+			interrupts = <28>;
+			clocks = <&gate_clk 4>;
+			bus-width = <4>;
+			cap-sdio-irq;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			status = "disabled";
+		};
+	};
+};

arch/arm/boot/dts/kirkwood-6281.dtsi

@@ -89,6 +89,8 @@ sata@80000 {
 			interrupts = <21>;
 			clocks = <&gate_clk 14>, <&gate_clk 15>;
 			clock-names = "0", "1";
+			phys = <&sata_phy0>, <&sata_phy1>;
+			phy-names = "port0", "port1";
 			status = "disabled";
 		};
 

arch/arm/boot/dts/kirkwood-6282.dtsi

@@ -104,6 +104,12 @@ pmx_sdio: pmx-sdio {
 			};
 		};
 
+		thermal@10078 {
+			compatible = "marvell,kirkwood-thermal";
+			reg = <0x10078 0x4>;
+			status = "okay";
+		};
+
 		rtc@10300 {
 			compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc";
 			reg = <0x10300 0x20>;
@@ -111,12 +117,25 @@ rtc@10300 {
 			clocks = <&gate_clk 7>;
 		};
 
+		i2c@11100 {
+			compatible = "marvell,mv64xxx-i2c";
+			reg = <0x11100 0x20>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <32>;
+			clock-frequency = <100000>;
+			clocks = <&gate_clk 7>;
+			status = "disabled";
+		};
+
 		sata@80000 {
 			compatible = "marvell,orion-sata";
 			reg = <0x80000 0x5000>;
 			interrupts = <21>;
 			clocks = <&gate_clk 14>, <&gate_clk 15>;
 			clock-names = "0", "1";
+			phys = <&sata_phy0>, <&sata_phy1>;
+			phy-names = "port0", "port1";
 			status = "disabled";
 		};
 
@@ -133,23 +152,5 @@ mvsdio@90000 {
 			cap-mmc-highspeed;
 			status = "disabled";
 		};
-
-		thermal@10078 {
-			compatible = "marvell,kirkwood-thermal";
-			reg = <0x10078 0x4>;
-			status = "okay";
-		};
-
-		i2c@11100 {
-			compatible = "marvell,mv64xxx-i2c";
-			reg = <0x11100 0x20>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			interrupts = <32>;
-			clock-frequency = <100000>;
-			clocks = <&gate_clk 7>;
-			status = "disabled";
-		};
-
 	};
 };

arch/arm/boot/dts/kirkwood-laplug.dts

+/*
+ * Copyright (C) 2013 Maxime Hadjinlian <maxime.hadjinlian@gmail.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "kirkwood.dtsi"
+#include "kirkwood-6192.dtsi"
+
+/ {
+	model = "LaCie LaPlug";
+	compatible = "lacie,laplug", "marvell,kirkwood-88f6192", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x8000000>; /* 128 MB */
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+	};
+
+	mbus {
+		pcie-controller {
+			status = "okay";
+			pcie@1,0 {
+				status = "okay";
+			};
+		};
+	};
+
+	ocp@f1000000 {
+		serial@12000 {
+			pinctrl-0 = <&pmx_uart0>;
+			pinctrl-names = "default";
+			status = "okay";
+		};
+
+		i2c@11000 {
+			pinctrl-0 = <&pmx_twsi0>;
+			pinctrl-names = "default";
+			status = "okay";
+
+			eeprom@50 {
+				compatible = "at,24c04";
+				pagesize = <16>;
+				reg = <0x50>;
+			};
+		};
+
+		pinctrl: pinctrl@10000 {
+			pmx_usb_power_enable: pmx-usb-power-enable {
+				marvell,pins = "mpp14";
+				marvell,function = "gpio";
+			};
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		button@1{
+			label = "Power push button";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		red-fail {
+			label = "laplug_v2:red:power";
+			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+		};
+		blue-power {
+			label = "laplug_v2:blue:power";
+			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+	};
+
+	gpio_poweroff {
+		compatible = "gpio-poweroff";
+		gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_usb_power_enable>;
+		pinctrl-names = "default";
+
+		usb_power_back1: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "USB Power Back 1";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb_power_back2: regulator@2 {
+			compatible = "regulator-fixed";
+			reg = <2>;
+			regulator-name = "USB Power Back 2";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+		};
+
+		usb_power_front: regulator@3 {
+			compatible = "regulator-fixed";
+			reg = <3>;
+			regulator-name = "USB Power Front";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&nand {
+	/* Total size : 512MB */
+	status = "okay";
+	pinctrl-0 = <&pmx_nand>;
+
+	partition@0 {
+		label = "u-boot";
+		reg = <0x0 0x100000>; /* 1MB */
+		read-only;
+	};
+
+	partition@100000 {
+		label = "uImage";
+		reg = <0x100000 0x1000000>; /* 16MB */
+	};
+
+	partition@1100000 {
+		label = "rootfs";
+		reg = <0x1100000 0x1EF00000>; /* 495MB */
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		device_type = "ethernet-phy";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};

arch/arm/boot/dts/kirkwood.dtsi

@@ -284,5 +284,23 @@ ethernet1-port@0 {
 				/* set phy-handle property in board file */
 			};
 		};
+
+		sata_phy0: sata-phy@82000 {
+			compatible = "marvell,mvebu-sata-phy";
+			reg = <0x82000 0x0334>;
+			clocks = <&gate_clk 14>;
+			clock-names = "sata";
+			#phy-cells = <0>;
+			status = "ok";
+		};
+
+		sata_phy1: sata-phy@84000 {
+			compatible = "marvell,mvebu-sata-phy";
+			reg = <0x84000 0x0334>;
+			clocks = <&gate_clk 15>;
+			clock-names = "sata";
+			#phy-cells = <0>;
+			status = "ok";
+		};
 	};
 };