bnx2x: Unify PHY attributes

Start building the infrastructure for dual media by adding new component
of PHY which will be used all along the function. Modify function to
work with this component instead of the link_params.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/bnx2x/bnx2x_ethtool.c

@@ -811,7 +811,7 @@ static int bnx2x_set_eeprom(struct net_device *dev,
 	struct bnx2x *bp = netdev_priv(dev);
 	int port = BP_PORT(bp);
 	int rc = 0;
-
+	u32 ext_phy_config;
 	if (!netif_running(dev))
 		return -EAGAIN;
 
@@ -827,6 +827,10 @@ static int bnx2x_set_eeprom(struct net_device *dev,
 	    !bp->port.pmf)
 		return -EINVAL;
 
+	ext_phy_config =
+		SHMEM_RD(bp,
+			 dev_info.port_hw_config[port].external_phy_config);
+
 	if (eeprom->magic == 0x50485950) {
 		/* 'PHYP' (0x50485950): prepare phy for FW upgrade */
 		bnx2x_stats_handle(bp, STATS_EVENT_STOP);
@@ -834,7 +838,7 @@ static int bnx2x_set_eeprom(struct net_device *dev,
 		bnx2x_acquire_phy_lock(bp);
 		rc |= bnx2x_link_reset(&bp->link_params,
 				       &bp->link_vars, 0);
-		if (XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config) ==
+		if (XGXS_EXT_PHY_TYPE(ext_phy_config) ==
 					PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101)
 			bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0,
 				       MISC_REGISTERS_GPIO_HIGH, port);
@@ -855,10 +859,8 @@ static int bnx2x_set_eeprom(struct net_device *dev,
 		}
 	} else if (eeprom->magic == 0x53985943) {
 		/* 'PHYC' (0x53985943): PHY FW upgrade completed */
-		if (XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config) ==
+		if (XGXS_EXT_PHY_TYPE(ext_phy_config) ==
 				       PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101) {
-			u8 ext_phy_addr =
-			     XGXS_EXT_PHY_ADDR(bp->link_params.ext_phy_config);
 
 			/* DSP Remove Download Mode */
 			bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0,
@@ -866,7 +868,8 @@ static int bnx2x_set_eeprom(struct net_device *dev,
 
 			bnx2x_acquire_phy_lock(bp);
 
-			bnx2x_sfx7101_sp_sw_reset(bp, port, ext_phy_addr);
+			bnx2x_sfx7101_sp_sw_reset(bp,
+						&bp->link_params.phy[EXT_PHY1]);
 
 			/* wait 0.5 sec to allow it to run */
 			msleep(500);

drivers/net/bnx2x/bnx2x_hsi.h

@@ -120,6 +120,23 @@ struct shared_hw_cfg {					 /* NVRAM Offset */
 #define SHARED_HW_CFG_FAN_FAILURE_DISABLED		      0x00080000
 #define SHARED_HW_CFG_FAN_FAILURE_ENABLED		      0x00100000
 
+	/* Set the MDC/MDIO access for the first external phy */
+#define SHARED_HW_CFG_MDC_MDIO_ACCESS1_MASK	    0x1C000000
+#define SHARED_HW_CFG_MDC_MDIO_ACCESS1_SHIFT	    26
+#define SHARED_HW_CFG_MDC_MDIO_ACCESS1_PHY_TYPE     0x00000000
+#define SHARED_HW_CFG_MDC_MDIO_ACCESS1_EMAC0	    0x04000000
+#define SHARED_HW_CFG_MDC_MDIO_ACCESS1_EMAC1	    0x08000000
+#define SHARED_HW_CFG_MDC_MDIO_ACCESS1_BOTH	    0x0c000000
+#define SHARED_HW_CFG_MDC_MDIO_ACCESS1_SWAPPED	    0x10000000
+
+	/* Set the MDC/MDIO access for the second external phy */
+#define SHARED_HW_CFG_MDC_MDIO_ACCESS2_MASK	    0xE0000000
+#define SHARED_HW_CFG_MDC_MDIO_ACCESS2_SHIFT	    29
+#define SHARED_HW_CFG_MDC_MDIO_ACCESS2_PHY_TYPE     0x00000000
+#define SHARED_HW_CFG_MDC_MDIO_ACCESS2_EMAC0	    0x20000000
+#define SHARED_HW_CFG_MDC_MDIO_ACCESS2_EMAC1	    0x40000000
+#define SHARED_HW_CFG_MDC_MDIO_ACCESS2_BOTH	    0x60000000
+#define SHARED_HW_CFG_MDC_MDIO_ACCESS2_SWAPPED	    0x80000000
 	u32 power_dissipated;					/* 0x11c */
 #define SHARED_HW_CFG_POWER_DIS_CMN_MASK	    0xff000000
 #define SHARED_HW_CFG_POWER_DIS_CMN_SHIFT	    24

drivers/net/bnx2x/bnx2x_link.h

-/* Copyright 2008-2009 Broadcom Corporation
+/* Copyright 2008-2010 Broadcom Corporation
  *
  * Unless you and Broadcom execute a separate written software license
  * agreement governing use of this software, this software is licensed to you
@@ -46,9 +46,35 @@
 #define SFP_EEPROM_PART_NO_ADDR 		0x28
 #define SFP_EEPROM_PART_NO_SIZE		16
 #define PWR_FLT_ERR_MSG_LEN			250
+/* Single Media Direct board is the plain 577xx board with CX4/RJ45 jacks */
+#define SINGLE_MEDIA_DIRECT(params)	(params->num_phys == 1)
+/* Single Media board contains single external phy */
+#define SINGLE_MEDIA(params)		(params->num_phys == 2)
 /***********************************************************/
 /*                         Structs                         */
 /***********************************************************/
+#define INT_PHY		0
+#define EXT_PHY1	1
+
+#define MAX_PHYS	2
+
+/***********************************************************/
+/*                      bnx2x_phy struct                     */
+/*  Defines the required arguments and function per phy    */
+/***********************************************************/
+struct link_vars;
+struct link_params;
+struct bnx2x_phy;
+
+struct bnx2x_phy {
+	u32 type;
+
+	/* Loaded during init */
+	u8 addr;
+
+	u32 mdio_ctrl;
+};
+
 /* Inputs parameters to the CLC */
 struct link_params {
 
@@ -106,6 +132,11 @@ struct link_params {
 #define FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED (1<<0)
 #define FEATURE_CONFIG_BC_SUPPORTS_OPT_MDL_VRFY	(1<<2)
 #define FEATURE_CONFIG_BCM8727_NOC			(1<<3)
+	/* Will be populated during common init */
+	struct bnx2x_phy phy[MAX_PHYS];
+
+	/* Will be populated during common init */
+	u8 num_phys;
 
 	/* Device pointer passed to all callback functions */
 	struct bnx2x *bp;
@@ -155,17 +186,20 @@ u8 bnx2x_link_reset(struct link_params *params, struct link_vars *vars,
 /* bnx2x_link_update should be called upon link interrupt */
 u8 bnx2x_link_update(struct link_params *input, struct link_vars *output);
 
-/* use the following cl45 functions to read/write from external_phy
+/* use the following phy functions to read/write from external_phy
   In order to use it to read/write internal phy registers, use
   DEFAULT_PHY_DEV_ADDR as devad, and (_bank + (_addr & 0xf)) as
-  Use ext_phy_type of 0 in case of cl22 over cl45
   the register */
-u8 bnx2x_cl45_read(struct bnx2x *bp, u8 port, u32 ext_phy_type,
-		 u8 phy_addr, u8 devad, u16 reg, u16 *ret_val);
+u8 bnx2x_phy_read(struct link_params *params, u8 phy_addr,
+		  u8 devad, u16 reg, u16 *ret_val);
 
-u8 bnx2x_cl45_write(struct bnx2x *bp, u8 port, u32 ext_phy_type,
-		  u8 phy_addr, u8 devad, u16 reg, u16 val);
+u8 bnx2x_phy_write(struct link_params *params, u8 phy_addr,
+		   u8 devad, u16 reg, u16 val);
+u8 bnx2x_cl45_read(struct bnx2x *bp, struct bnx2x_phy *phy,
+		   u8 devad, u16 reg, u16 *ret_val);
 
+u8 bnx2x_cl45_write(struct bnx2x *bp, struct bnx2x_phy *phy,
+		    u8 devad, u16 reg, u16 val);
 /* Reads the link_status from the shmem,
    and update the link vars accordingly */
 void bnx2x_link_status_update(struct link_params *input,
@@ -198,9 +232,14 @@ u8 bnx2x_common_init_phy(struct bnx2x *bp, u32 shmem_base);
 /* Reset the external PHY using GPIO */
 void bnx2x_ext_phy_hw_reset(struct bnx2x *bp, u8 port);
 
-void bnx2x_sfx7101_sp_sw_reset(struct bnx2x *bp, u8 port, u8 phy_addr);
+/* Reset the external of SFX7101 */
+void bnx2x_sfx7101_sp_sw_reset(struct bnx2x *bp, struct bnx2x_phy *phy);
 
-u8 bnx2x_read_sfp_module_eeprom(struct link_params *params, u16 addr,
+u8 bnx2x_read_sfp_module_eeprom(struct bnx2x_phy *phy,
+				struct link_params *params, u16 addr,
 			      u8 byte_cnt, u8 *o_buf);
-
+/* Returns the aggregative supported attributes of the phys on board */
+u32 bnx2x_supported_attr(struct link_params *params, u8 phy_idx);
+/* Probe the phys on board, and populate them in "params" */
+u8 bnx2x_phy_probe(struct link_params *params);
 #endif /* BNX2X_LINK_H */

drivers/net/bnx2x/bnx2x_main.c

@@ -4351,7 +4351,6 @@ static int bnx2x_init_port(struct bnx2x *bp)
 	default:
 		break;
 	}
-
 	bnx2x__link_reset(bp);
 
 	return 0;
@@ -6984,23 +6983,15 @@ static int bnx2x_mdio_read(struct net_device *netdev, int prtad,
 	struct bnx2x *bp = netdev_priv(netdev);
 	u16 value;
 	int rc;
-	u32 phy_type = XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config);
 
 	DP(NETIF_MSG_LINK, "mdio_read: prtad 0x%x, devad 0x%x, addr 0x%x\n",
 	   prtad, devad, addr);
 
-	if (prtad != bp->mdio.prtad) {
-		DP(NETIF_MSG_LINK, "prtad missmatch (cmd:0x%x != bp:0x%x)\n",
-		   prtad, bp->mdio.prtad);
-		return -EINVAL;
-	}
-
 	/* The HW expects different devad if CL22 is used */
 	devad = (devad == MDIO_DEVAD_NONE) ? DEFAULT_PHY_DEV_ADDR : devad;
 
 	bnx2x_acquire_phy_lock(bp);
-	rc = bnx2x_cl45_read(bp, BP_PORT(bp), phy_type, prtad,
-			     devad, addr, &value);
+	rc = bnx2x_phy_read(&bp->link_params, prtad, devad, addr, &value);
 	bnx2x_release_phy_lock(bp);
 	DP(NETIF_MSG_LINK, "mdio_read_val 0x%x rc = 0x%x\n", value, rc);
 
@@ -7014,24 +7005,16 @@ static int bnx2x_mdio_write(struct net_device *netdev, int prtad, int devad,
 			    u16 addr, u16 value)
 {
 	struct bnx2x *bp = netdev_priv(netdev);
-	u32 ext_phy_type = XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config);
 	int rc;
 
 	DP(NETIF_MSG_LINK, "mdio_write: prtad 0x%x, devad 0x%x, addr 0x%x,"
 			   " value 0x%x\n", prtad, devad, addr, value);
 
-	if (prtad != bp->mdio.prtad) {
-		DP(NETIF_MSG_LINK, "prtad missmatch (cmd:0x%x != bp:0x%x)\n",
-		   prtad, bp->mdio.prtad);
-		return -EINVAL;
-	}
-
 	/* The HW expects different devad if CL22 is used */
 	devad = (devad == MDIO_DEVAD_NONE) ? DEFAULT_PHY_DEV_ADDR : devad;
 
 	bnx2x_acquire_phy_lock(bp);
-	rc = bnx2x_cl45_write(bp, BP_PORT(bp), ext_phy_type, prtad,
-			      devad, addr, value);
+	rc = bnx2x_phy_write(&bp->link_params, prtad, devad, addr, value);
 	bnx2x_release_phy_lock(bp);
 	return rc;
 }

drivers/net/bnx2x/bnx2x_reg.h

@@ -5135,18 +5135,22 @@ Theotherbitsarereservedandshouldbezero*/
 #define MDIO_PMA_REG_8727_TWO_WIRE_SLAVE_ADDR	0x8005
 #define MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF	0x8007
 #define MDIO_PMA_REG_8727_TWO_WIRE_DATA_MASK 0xff
-#define MDIO_PMA_REG_8727_MISC_CTRL		0x8309
 #define MDIO_PMA_REG_8727_TX_CTRL1		0xca02
 #define MDIO_PMA_REG_8727_TX_CTRL2		0xca05
 #define MDIO_PMA_REG_8727_PCS_OPT_CTRL		0xc808
 #define MDIO_PMA_REG_8727_GPIO_CTRL		0xc80e
+#define MDIO_PMA_REG_8727_PCS_GP		0xc842
+
+#define MDIO_AN_REG_8727_MISC_CTRL		0x8309
 
 #define MDIO_PMA_REG_8073_CHIP_REV			0xc801
 #define MDIO_PMA_REG_8073_SPEED_LINK_STATUS		0xc820
 #define MDIO_PMA_REG_8073_XAUI_WA			0xc841
+#define MDIO_PMA_REG_8073_OPT_DIGITAL_CTRL		0xcd08
 
 #define MDIO_PMA_REG_7101_RESET 	0xc000
 #define MDIO_PMA_REG_7107_LED_CNTL	0xc007
+#define MDIO_PMA_REG_7107_LINK_LED_CNTL 0xc009
 #define MDIO_PMA_REG_7101_VER1		0xc026
 #define MDIO_PMA_REG_7101_VER2		0xc027
 
@@ -5210,11 +5214,13 @@ Theotherbitsarereservedandshouldbezero*/
 #define MDIO_AN_REG_CL37_FC_LP		0xffe5
 
 #define MDIO_AN_REG_8073_2_5G		0x8329
+#define MDIO_AN_REG_8073_BAM		0x8350
 
-#define MDIO_AN_REG_8727_MISC_CTRL	0x8309
 #define MDIO_AN_REG_8481_10GBASE_T_AN_CTRL	0x0020
 #define MDIO_AN_REG_8481_LEGACY_MII_CTRL	0xffe0
+#define MDIO_AN_REG_8481_LEGACY_MII_STATUS	0xffe1
 #define MDIO_AN_REG_8481_LEGACY_AN_ADV		0xffe4
+#define MDIO_AN_REG_8481_LEGACY_AN_EXPANSION	0xffe6
 #define MDIO_AN_REG_8481_1000T_CTRL		0xffe9
 #define MDIO_AN_REG_8481_EXPANSION_REG_RD_RW	0xfff5
 #define MDIO_AN_REG_8481_EXPANSION_REG_ACCESS	0xfff7