ARM: kirkwood: Add dts file describing HP T5325 thin client

Describe the T5325 using device tree properties, where possible.  The
first version of this file was produced by Thomas Petazzoni.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

arch/arm/boot/dts/Makefile

@@ -132,6 +132,7 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-b3.dtb \
 	kirkwood-rs411.dtb \
 	kirkwood-sheevaplug.dtb \
 	kirkwood-sheevaplug-esata.dtb \
+	kirkwood-t5325.dtb \
 	kirkwood-topkick.dtb \
 	kirkwood-ts219-6281.dtb \
 	kirkwood-ts219-6282.dtb \

arch/arm/boot/dts/kirkwood-t5325.dts

+/*
+ * Device Tree file for HP t5325 Thin Client"
+ *
+ * Copyright (C) 2014
+ *
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ * Andrew Lunn <andrew@lunn.ch>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+*/
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	model = "HP t5325 Thin Client";
+	compatible = "hp,t5325", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+	};
+
+	mbus {
+		pcie-controller {
+			status = "okay";
+
+			pcie@1,0 {
+				status = "okay";
+			};
+		};
+	};
+
+	ocp@f1000000 {
+		pinctrl: pinctrl@10000 {
+			pinctrl-0 = <&pmx_i2s &pmx_sysrst>;
+			pinctrl-names = "default";
+
+			pmx_button_power: pmx-button_power {
+				marvell,pins = "mpp45";
+				marvell,function = "gpio";
+			};
+
+			pmx_power_off: pmx-power-off {
+				marvell,pins = "mpp48";
+				marvell,function = "gpio";
+			};
+
+			pmx_led: pmx-led {
+				marvell,pins = "mpp21";
+				marvell,function = "gpio";
+			};
+
+			pmx_usb_sata_power_enable: pmx-usb-sata-power-enable {
+				marvell,pins = "mpp44";
+				marvell,function = "gpio";
+			};
+
+			/*
+			 * Redefined from kirkwood-6281.dtsi, because
+			 * we don't use SPI CS on MPP0, but on MPP7.
+			 */
+			pmx_spi: pmx-spi {
+				marvell,pins = "mpp1", "mpp2", "mpp3", "mpp7";
+				marvell,function = "spi";
+			};
+
+			pmx_sysrst: pmx-sysrst {
+				marvell,pins = "mpp6";
+				marvell,function = "sysrst";
+			};
+
+			pmx_i2s: pmx-i2s {
+				marvell,pins = "mpp39", "mpp40", "mpp41", "mpp42",
+					       "mpp43";
+				marvell,function = "audio";
+			};
+		};
+
+		spi@10600 {
+			pinctrl-0 = <&pmx_spi>;
+			pinctrl-names = "default";
+			status = "okay";
+
+			flash@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "st,m25p80";
+				spi-max-frequency = <86000000>;
+				reg = <0>;
+				mode = <0>;
+
+				partition@0 {
+					reg = <0x0 0x80000>;
+					label = "u-boot";
+				};
+
+				partition@1 {
+					reg = <0x80000 0x40000>;
+					label = "SSD firmware";
+				};
+
+				partition@2 {
+					reg = <0xc0000 0x10000>;
+					label = "u-boot env";
+				};
+
+				partition@3 {
+					reg = <0xd0000 0x10000>;
+					label = "permanent u-boot env";
+				};
+
+				partition@4 {
+					reg = <0xd0000 0x10000>;
+					label = "permanent u-boot env";
+				};
+			};
+		};
+
+		i2c@11000 {
+			status = "okay";
+
+			alc5621: alc5621@1a {
+				compatible = "realtek,alc5621";
+				reg = <0x1a>;
+			};
+		};
+
+		serial@12000 {
+			status = "okay";
+		};
+
+		sata@80000 {
+			status = "okay";
+			nr-ports = <2>;
+		};
+
+		audio: audio-controller@a0000 {
+			status = "okay";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_usb_sata_power_enable>;
+		pinctrl-names = "default";
+
+		usb_power: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "USB-SATA Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_button_power>;
+		pinctrl-names = "default";
+
+		button@1 {
+			label = "Power Button";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio_poweroff {
+		compatible = "gpio-poweroff";
+		pinctrl-0 = <&pmx_power_off>;
+		pinctrl-names = "default";
+		gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+	};
+
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy {
+		device_type = "ethernet-phy";
+		reg = <8>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};