Merge branch 'for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata

Pull libata updates from Tejun Heo:
 "The biggest core change is removal of SCT WRITE SAME support, which
  never worked properly.

  Other than that, trivial updates in core code and specific embedded
  driver updates"

* 'for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  libata: remove SCT WRITE SAME support
  libata: reject passthrough WRITE SAME requests
  dt-bindings: ata: add DT bindings for ahci-dm816 SATA controller
  ata: ahci: add support for DaVinci DM816 SATA controller
  pata: remove the at91 driver
  libata: make ata_sg_clean static over again
  libata: use setup_deferrable_timer
  ata: allow subsystem to be used on m32r and s390 archs
  Delete redundant return value check of platform_get_resource()
  ata: constify of_device_id structures

Documentation/devicetree/bindings/ata/ahci-dm816.txt

+Device tree binding for the TI DM816 AHCI SATA Controller
+---------------------------------------------------------
+
+Required properties:
+  - compatible: must be "ti,dm816-ahci"
+  - reg: physical base address and size of the register region used by
+         the controller (as defined by the AHCI 1.1 standard)
+  - interrupts: interrupt specifier (refer to the interrupt binding)
+  - clocks: list of phandle and clock specifier pairs (or only
+            phandles for clock providers with '0' defined for
+            #clock-cells); two clocks must be specified: the functional
+            clock and an external reference clock
+
+Example:
+
+	sata: sata@4a140000 {
+		compatible = "ti,dm816-ahci";
+		reg = <0x4a140000 0x10000>;
+		interrupts = <16>;
+		clocks = <&sysclk5_ck>, <&sata_refclk>;
+	};

drivers/ata/Kconfig

@@ -14,7 +14,6 @@ menuconfig ATA
 	tristate "Serial ATA and Parallel ATA drivers (libata)"
 	depends on HAS_IOMEM
 	depends on BLOCK
-	depends on !(M32R || S390) || BROKEN
 	select SCSI
 	select GLOB
 	---help---
@@ -118,6 +117,15 @@ config AHCI_DA850
 
 	  If unsure, say N.
 
+config AHCI_DM816
+	tristate "DaVinci DM816 AHCI SATA support"
+	depends on ARCH_OMAP2PLUS
+	help
+	  This option enables support for the DaVinci DM816 SoC's
+	  onboard AHCI SATA controller.
+
+	  If unsure, say N.
+
 config AHCI_ST
 	tristate "ST AHCI SATA support"
 	depends on ARCH_STI
@@ -885,14 +893,6 @@ config PATA_AT32
 
 	  If unsure, say N.
 
-config PATA_AT91
-	tristate "PATA support for AT91SAM9260"
-	depends on ARM && SOC_AT91SAM9
-	help
-	  This option enables support for IDE devices on the Atmel AT91SAM9260 SoC.
-
-	  If unsure, say N.
-
 config PATA_CMD640_PCI
 	tristate "CMD640 PCI PATA support (Experimental)"
 	depends on PCI

drivers/ata/Makefile

@@ -14,6 +14,7 @@ obj-$(CONFIG_SATA_HIGHBANK)	+= sata_highbank.o libahci.o
 obj-$(CONFIG_AHCI_BRCM)		+= ahci_brcm.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_CEVA)		+= ahci_ceva.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_DA850)	+= ahci_da850.o libahci.o libahci_platform.o
+obj-$(CONFIG_AHCI_DM816)	+= ahci_dm816.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_IMX)		+= ahci_imx.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_MVEBU)	+= ahci_mvebu.o libahci.o libahci_platform.o
 obj-$(CONFIG_AHCI_OCTEON)	+= ahci_octeon.o
@@ -91,7 +92,6 @@ obj-$(CONFIG_PATA_WINBOND)	+= pata_sl82c105.o
 
 # SFF PIO only
 obj-$(CONFIG_PATA_AT32)		+= pata_at32.o
-obj-$(CONFIG_PATA_AT91)		+= pata_at91.o
 obj-$(CONFIG_PATA_CMD640_PCI)	+= pata_cmd640.o
 obj-$(CONFIG_PATA_FALCON)	+= pata_falcon.o
 obj-$(CONFIG_PATA_ISAPNP)	+= pata_isapnp.o

drivers/ata/ahci_dm816.c

+/*
+ * DaVinci DM816 AHCI SATA platform driver
+ *
+ * Copyright (C) 2017 BayLibre SAS
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/pm.h>
+#include <linux/platform_device.h>
+#include <linux/libata.h>
+#include <linux/ahci_platform.h>
+
+#include "ahci.h"
+
+#define AHCI_DM816_DRV_NAME		"ahci-dm816"
+
+#define AHCI_DM816_PHY_ENPLL(x)		((x) << 0)
+#define AHCI_DM816_PHY_MPY(x)		((x) << 1)
+#define AHCI_DM816_PHY_LOS(x)		((x) << 12)
+#define AHCI_DM816_PHY_RXCDR(x)		((x) << 13)
+#define AHCI_DM816_PHY_RXEQ(x)		((x) << 16)
+#define AHCI_DM816_PHY_TXSWING(x)	((x) << 23)
+
+#define AHCI_DM816_P0PHYCR_REG		0x178
+#define AHCI_DM816_P1PHYCR_REG		0x1f8
+
+#define AHCI_DM816_PLL_OUT		1500000000LU
+
+static const unsigned long pll_mpy_table[] = {
+	  400,  500,  600,  800,  825, 1000, 1200,
+	 1250, 1500, 1600, 1650, 2000, 2200, 2500
+};
+
+static int ahci_dm816_get_mpy_bits(unsigned long refclk_rate)
+{
+	unsigned long pll_multiplier;
+	int i;
+
+	/*
+	 * We need to determine the value of the multiplier (MPY) bits.
+	 * In order to include the 8.25 multiplier we need to first divide
+	 * the refclk rate by 100.
+	 */
+	pll_multiplier = AHCI_DM816_PLL_OUT / (refclk_rate / 100);
+
+	for (i = 0; i < ARRAY_SIZE(pll_mpy_table); i++) {
+		if (pll_mpy_table[i] == pll_multiplier)
+			return i;
+	}
+
+	/*
+	 * We should have divided evenly - if not, return an invalid
+	 * value.
+	 */
+	return -1;
+}
+
+static int ahci_dm816_phy_init(struct ahci_host_priv *hpriv, struct device *dev)
+{
+	unsigned long refclk_rate;
+	int mpy;
+	u32 val;
+
+	/*
+	 * We should have been supplied two clocks: the functional and
+	 * keep-alive clock and the external reference clock. We need the
+	 * rate of the latter to calculate the correct value of MPY bits.
+	 */
+	if (!hpriv->clks[1]) {
+		dev_err(dev, "reference clock not supplied\n");
+		return -EINVAL;
+	}
+
+	refclk_rate = clk_get_rate(hpriv->clks[1]);
+	if ((refclk_rate % 100) != 0) {
+		dev_err(dev, "reference clock rate must be divisible by 100\n");
+		return -EINVAL;
+	}
+
+	mpy = ahci_dm816_get_mpy_bits(refclk_rate);
+	if (mpy < 0) {
+		dev_err(dev, "can't calculate the MPY bits value\n");
+		return -EINVAL;
+	}
+
+	/* Enable the PHY and configure the first HBA port. */
+	val = AHCI_DM816_PHY_MPY(mpy) | AHCI_DM816_PHY_LOS(1) |
+	      AHCI_DM816_PHY_RXCDR(4) | AHCI_DM816_PHY_RXEQ(1) |
+	      AHCI_DM816_PHY_TXSWING(3) | AHCI_DM816_PHY_ENPLL(1);
+	writel(val, hpriv->mmio + AHCI_DM816_P0PHYCR_REG);
+
+	/* Configure the second HBA port. */
+	val = AHCI_DM816_PHY_LOS(1) | AHCI_DM816_PHY_RXCDR(4) |
+	      AHCI_DM816_PHY_RXEQ(1) | AHCI_DM816_PHY_TXSWING(3);
+	writel(val, hpriv->mmio + AHCI_DM816_P1PHYCR_REG);
+
+	return 0;
+}
+
+static int ahci_dm816_softreset(struct ata_link *link,
+				unsigned int *class, unsigned long deadline)
+{
+	int pmp, ret;
+
+	pmp = sata_srst_pmp(link);
+
+	/*
+	 * There's an issue with the SATA controller on DM816 SoC: if we
+	 * enable Port Multiplier support, but the drive is connected directly
+	 * to the board, it can't be detected. As a workaround: if PMP is
+	 * enabled, we first call ahci_do_softreset() and pass it the result of
+	 * sata_srst_pmp(). If this call fails, we retry with pmp = 0.
+	 */
+	ret = ahci_do_softreset(link, class, pmp, deadline, ahci_check_ready);
+	if (pmp && ret == -EBUSY)
+		return ahci_do_softreset(link, class, 0,
+					 deadline, ahci_check_ready);
+
+	return ret;
+}
+
+static struct ata_port_operations ahci_dm816_port_ops = {
+	.inherits = &ahci_platform_ops,
+	.softreset = ahci_dm816_softreset,
+};
+
+static const struct ata_port_info ahci_dm816_port_info = {
+	.flags		= AHCI_FLAG_COMMON,
+	.pio_mask	= ATA_PIO4,
+	.udma_mask	= ATA_UDMA6,
+	.port_ops	= &ahci_dm816_port_ops,
+};
+
+static struct scsi_host_template ahci_dm816_platform_sht = {
+	AHCI_SHT(AHCI_DM816_DRV_NAME),
+};
+
+static int ahci_dm816_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct ahci_host_priv *hpriv;
+	int rc;
+
+	hpriv = ahci_platform_get_resources(pdev);
+	if (IS_ERR(hpriv))
+		return PTR_ERR(hpriv);
+
+	rc = ahci_platform_enable_resources(hpriv);
+	if (rc)
+		return rc;
+
+	rc = ahci_dm816_phy_init(hpriv, dev);
+	if (rc)
+		goto disable_resources;
+
+	rc = ahci_platform_init_host(pdev, hpriv,
+				     &ahci_dm816_port_info,
+				     &ahci_dm816_platform_sht);
+	if (rc)
+		goto disable_resources;
+
+	return 0;
+
+disable_resources:
+	ahci_platform_disable_resources(hpriv);
+
+	return rc;
+}
+
+static SIMPLE_DEV_PM_OPS(ahci_dm816_pm_ops,
+			 ahci_platform_suspend,
+			 ahci_platform_resume);
+
+static const struct of_device_id ahci_dm816_of_match[] = {
+	{ .compatible = "ti,dm816-ahci", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, ahci_dm816_of_match);
+
+static struct platform_driver ahci_dm816_driver = {
+	.probe = ahci_dm816_probe,
+	.remove = ata_platform_remove_one,
+	.driver = {
+		.name = AHCI_DM816_DRV_NAME,
+		.of_match_table = ahci_dm816_of_match,
+		.pm = &ahci_dm816_pm_ops,
+	},
+};
+module_platform_driver(ahci_dm816_driver);
+
+MODULE_DESCRIPTION("DaVinci DM816 AHCI SATA platform driver");
+MODULE_AUTHOR("Bartosz Golaszewski <bgolaszewski@baylibre.com>");
+MODULE_LICENSE("GPL");

drivers/ata/ahci_octeon.c

@@ -38,11 +38,6 @@ static int ahci_octeon_probe(struct platform_device *pdev)
 	int ret;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!res) {
-		dev_err(&pdev->dev, "Platform resource[0] is missing\n");
-		return -ENODEV;
-	}
-
 	base = devm_ioremap_resource(&pdev->dev, res);
 	if (IS_ERR(base))
 		return PTR_ERR(base);

drivers/ata/libata-core.c

@@ -4910,7 +4910,7 @@ void ata_sg_init(struct ata_queued_cmd *qc, struct scatterlist *sg,
  *	LOCKING:
  *	spin_lock_irqsave(host lock)
  */
-void ata_sg_clean(struct ata_queued_cmd *qc)
+static void ata_sg_clean(struct ata_queued_cmd *qc)
 {
 	struct ata_port *ap = qc->ap;
 	struct scatterlist *sg = qc->sg;
@@ -5902,9 +5902,9 @@ struct ata_port *ata_port_alloc(struct ata_host *host)
 	INIT_LIST_HEAD(&ap->eh_done_q);
 	init_waitqueue_head(&ap->eh_wait_q);
 	init_completion(&ap->park_req_pending);
-	init_timer_deferrable(&ap->fastdrain_timer);
-	ap->fastdrain_timer.function = ata_eh_fastdrain_timerfn;
-	ap->fastdrain_timer.data = (unsigned long)ap;
+	setup_deferrable_timer(&ap->fastdrain_timer,
+			       ata_eh_fastdrain_timerfn,
+			       (unsigned long)ap);
 
 	ap->cbl = ATA_CBL_NONE;
 

drivers/ata/libata-scsi.c

@@ -3392,46 +3392,6 @@ static size_t ata_format_dsm_trim_descr(struct scsi_cmnd *cmd, u32 trmax,
 	return r;
 }
 
-/**
- * ata_format_dsm_trim_descr() - SATL Write Same to ATA SCT Write Same
- * @cmd: SCSI command being translated
- * @lba: Starting sector
- * @num: Number of sectors to be zero'd.
- *
- * Rewrite the WRITE SAME payload to be an SCT Write Same formatted
- * descriptor.
- * NOTE: Writes a pattern (0's) in the foreground.
- *
- * Return: Number of bytes copied into sglist.
- */
-static size_t ata_format_sct_write_same(struct scsi_cmnd *cmd, u64 lba, u64 num)
-{
-	struct scsi_device *sdp = cmd->device;
-	size_t len = sdp->sector_size;
-	size_t r;
-	u16 *buf;
-	unsigned long flags;
-
-	spin_lock_irqsave(&ata_scsi_rbuf_lock, flags);
-	buf = ((void *)ata_scsi_rbuf);
-
-	put_unaligned_le16(0x0002,  &buf[0]); /* SCT_ACT_WRITE_SAME */
-	put_unaligned_le16(0x0101,  &buf[1]); /* WRITE PTRN FG */
-	put_unaligned_le64(lba,     &buf[2]);
-	put_unaligned_le64(num,     &buf[6]);
-	put_unaligned_le32(0u,      &buf[10]); /* pattern */
-
-	WARN_ON(len > ATA_SCSI_RBUF_SIZE);
-
-	if (len > ATA_SCSI_RBUF_SIZE)
-		len = ATA_SCSI_RBUF_SIZE;
-
-	r = sg_copy_from_buffer(scsi_sglist(cmd), scsi_sg_count(cmd), buf, len);
-	spin_unlock_irqrestore(&ata_scsi_rbuf_lock, flags);
-
-	return r;
-}
-
 /**
  * ata_scsi_write_same_xlat() - SATL Write Same to ATA SCT Write Same
  * @qc: Command to be translated
@@ -3462,15 +3422,22 @@ static unsigned int ata_scsi_write_same_xlat(struct ata_queued_cmd *qc)
 	if (unlikely(!dev->dma_mode))
 		goto invalid_opcode;
 
+	/*
+	 * We only allow sending this command through the block layer,
+	 * as it modifies the DATA OUT buffer, which would corrupt user
+	 * memory for SG_IO commands.
+	 */
+	if (unlikely(blk_rq_is_passthrough(scmd->request)))
+		goto invalid_opcode;
+
 	if (unlikely(scmd->cmd_len < 16)) {
 		fp = 15;
 		goto invalid_fld;
 	}
 	scsi_16_lba_len(cdb, &block, &n_block);
 
-	if (unmap) {
-		/* If trim is not enabled the cmd is invalid. */
-		if ((dev->horkage & ATA_HORKAGE_NOTRIM) ||
+	if (!unmap ||
+	    (dev->horkage & ATA_HORKAGE_NOTRIM) ||
 	    !ata_id_has_trim(dev->id)) {
 		fp = 1;
 		bp = 3;
@@ -3481,14 +3448,6 @@ static unsigned int ata_scsi_write_same_xlat(struct ata_queued_cmd *qc)
 		fp = 2;
 		goto invalid_fld;
 	}
-	} else {
-		/* If write same is not available the cmd is invalid */
-		if (!ata_id_sct_write_same(dev->id)) {
-			fp = 1;
-			bp = 3;
-			goto invalid_fld;
-		}
-	}
 
 	/*
 	 * WRITE SAME always has a sector sized buffer as payload, this
@@ -3502,7 +3461,7 @@ static unsigned int ata_scsi_write_same_xlat(struct ata_queued_cmd *qc)
 	 * For DATA SET MANAGEMENT TRIM in ACS-2 nsect (aka count)
 	 * is defined as number of 512 byte blocks to be transferred.
 	 */
-	if (unmap) {
+
 	size = ata_format_dsm_trim_descr(scmd, trmax, block, n_block);
 	if (size != len)
 		goto invalid_param_len;
@@ -3525,27 +3484,6 @@ static unsigned int ata_scsi_write_same_xlat(struct ata_queued_cmd *qc)
 		tf->nsect = size / 512;
 		tf->command = ATA_CMD_DSM;
 	}
-	} else {
-		size = ata_format_sct_write_same(scmd, block, n_block);
-		if (size != len)
-			goto invalid_param_len;
-
-		tf->hob_feature = 0;
-		tf->feature = 0;
-		tf->hob_nsect = 0;
-		tf->nsect = 1;
-		tf->lbah = 0;
-		tf->lbam = 0;
-		tf->lbal = ATA_CMD_STANDBYNOW1;
-		tf->hob_lbah = 0;
-		tf->hob_lbam = 0;
-		tf->hob_lbal = 0;
-		tf->device = ATA_CMD_STANDBYNOW1;
-		tf->protocol = ATA_PROT_DMA;
-		tf->command = ATA_CMD_WRITE_LOG_DMA_EXT;
-		if (unlikely(dev->flags & ATA_DFLAG_PIO))
-			tf->command = ATA_CMD_WRITE_LOG_EXT;
-	}
 
 	tf->flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE | ATA_TFLAG_LBA48 |
 		     ATA_TFLAG_WRITE;
@@ -3619,10 +3557,6 @@ static unsigned int ata_scsiop_maint_in(struct ata_scsi_args *args, u8 *rbuf)
 	case START_STOP:
 		supported = 3;
 		break;
-	case WRITE_SAME_16:
-		if (!ata_id_sct_write_same(dev->id))
-			break;
-		/* fallthrough: if SCT ... only enable for ZBC */
 	case ZBC_IN:
 	case ZBC_OUT:
 		if (ata_id_zoned_cap(dev->id) ||

drivers/ata/pata_at91.c

-/*
- * PATA driver for AT91SAM9260 Static Memory Controller
- * with CompactFlash interface in True IDE mode
- *
- * Copyright (C) 2009 Matyukevich Sergey
- *               2011 Igor Plyatov
- *
- * Based on:
- *      * generic platform driver by Paul Mundt: drivers/ata/pata_platform.c
- *      * pata_at32 driver by Kristoffer Nyborg Gregertsen
- *      * at91_ide driver by Stanislaw Gruszka
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2
- * as published by the Free Software Foundation.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/blkdev.h>
-#include <linux/gfp.h>
-#include <scsi/scsi_host.h>
-#include <linux/ata.h>
-#include <linux/clk.h>
-#include <linux/libata.h>
-#include <linux/mfd/syscon.h>
-#include <linux/mfd/syscon/atmel-smc.h>
-#include <linux/platform_device.h>
-#include <linux/ata_platform.h>
-#include <linux/platform_data/atmel.h>
-#include <linux/regmap.h>
-#include <linux/gpio.h>
-
-#define DRV_NAME		"pata_at91"
-#define DRV_VERSION		"0.3"
-
-#define CF_IDE_OFFSET		0x00c00000
-#define CF_ALT_IDE_OFFSET	0x00e00000
-#define CF_IDE_RES_SIZE		0x08
-#define CS_PULSE_MAXIMUM	319
-#define ER_SMC_CALC		1
-#define ER_SMC_RECALC		2
-
-struct at91_ide_info {
-	unsigned long mode;
-	unsigned int cs;
-	struct clk *mck;
-	void __iomem *ide_addr;
-	void __iomem *alt_addr;
-};
-
-/**
- * struct smc_range - range of valid values for SMC register.
- */
-struct smc_range {
-	int min;
-	int max;
-};
-
-struct regmap *smc;
-
-struct at91sam9_smc_generic_fields {
-	struct regmap_field *setup;
-	struct regmap_field *pulse;
-	struct regmap_field *cycle;
-	struct regmap_field *mode;
-} fields;
-
-/**
- * adjust_smc_value - adjust value for one of SMC registers.
- * @value: adjusted value
- * @range: array of SMC ranges with valid values
- * @size: SMC ranges array size
- *
- * This returns the difference between input and output value or negative
- * in case of invalid input value.
- * If negative returned, then output value = maximal possible from ranges.
- */
-static int adjust_smc_value(int *value, struct smc_range *range, int size)
-{
-	int maximum = (range + size - 1)->max;
-	int remainder;
-
-	do {
-		if (*value < range->min) {
-			remainder = range->min - *value;
-			*value = range->min; /* nearest valid value */
-			return remainder;
-		} else if ((range->min <= *value) && (*value <= range->max))
-			return 0;
-
-		range++;
-	} while (--size);
-	*value = maximum;
-
-	return -1; /* invalid value */
-}
-
-/**
- * calc_smc_vals - calculate SMC register values
- * @dev: ATA device
- * @setup: SMC_SETUP register value
- * @pulse: SMC_PULSE register value
- * @cycle: SMC_CYCLE register value
- *
- * This returns negative in case of invalid values for SMC registers:
- * -ER_SMC_RECALC - recalculation required for SMC values,
- * -ER_SMC_CALC - calculation failed (invalid input values).
- *
- * SMC use special coding scheme, see "Coding and Range of Timing
- * Parameters" table from AT91SAM9 datasheets.
- *
- *	SMC_SETUP = 128*setup[5] + setup[4:0]
- *	SMC_PULSE = 256*pulse[6] + pulse[5:0]
- *	SMC_CYCLE = 256*cycle[8:7] + cycle[6:0]
- */
-static int calc_smc_vals(struct device *dev,
-		int *setup, int *pulse, int *cycle, int *cs_pulse)
-{
-	int ret_val;
-	int err = 0;
-	struct smc_range range_setup[] = {	/* SMC_SETUP valid values */
-		{.min = 0,	.max = 31},	/* first  range */
-		{.min = 128,	.max = 159}	/* second range */
-	};
-	struct smc_range range_pulse[] = {	/* SMC_PULSE valid values */
-		{.min = 0,	.max = 63},	/* first  range */
-		{.min = 256,	.max = 319}	/* second range */
-	};
-	struct smc_range range_cycle[] = {	/* SMC_CYCLE valid values */
-		{.min = 0,	.max = 127},	/* first  range */
-		{.min = 256,	.max = 383},	/* second range */
-		{.min = 512,	.max = 639},	/* third  range */
-		{.min = 768,	.max = 895}	/* fourth range */
-	};
-
-	ret_val = adjust_smc_value(setup, range_setup, ARRAY_SIZE(range_setup));
-	if (ret_val < 0)
-		dev_warn(dev, "maximal SMC Setup value\n");
-	else
-		*cycle += ret_val;
-
-	ret_val = adjust_smc_value(pulse, range_pulse, ARRAY_SIZE(range_pulse));
-	if (ret_val < 0)
-		dev_warn(dev, "maximal SMC Pulse value\n");
-	else
-		*cycle += ret_val;
-
-	ret_val = adjust_smc_value(cycle, range_cycle, ARRAY_SIZE(range_cycle));
-	if (ret_val < 0)
-		dev_warn(dev, "maximal SMC Cycle value\n");
-
-	*cs_pulse = *cycle;
-	if (*cs_pulse > CS_PULSE_MAXIMUM) {
-		dev_err(dev, "unable to calculate valid SMC settings\n");
-		return -ER_SMC_CALC;
-	}
-
-	ret_val = adjust_smc_value(cs_pulse, range_pulse,
-					ARRAY_SIZE(range_pulse));
-	if (ret_val < 0) {
-		dev_warn(dev, "maximal SMC CS Pulse value\n");
-	} else if (ret_val != 0) {
-		*cycle = *cs_pulse;
-		dev_warn(dev, "SMC Cycle extended\n");
-		err = -ER_SMC_RECALC;
-	}
-
-	return err;
-}
-
-/**
- * to_smc_format - convert values into SMC format
- * @setup: SETUP value of SMC Setup Register
- * @pulse: PULSE value of SMC Pulse Register
- * @cycle: CYCLE value of SMC Cycle Register
- * @cs_pulse: NCS_PULSE value of SMC Pulse Register
- */
-static void to_smc_format(int *setup, int *pulse, int *cycle, int *cs_pulse)
-{
-	*setup = (*setup & 0x1f) | ((*setup & 0x80) >> 2);
-	*pulse = (*pulse & 0x3f) | ((*pulse & 0x100) >> 2);
-	*cycle = (*cycle & 0x7f) | ((*cycle & 0x300) >> 1);
-	*cs_pulse = (*cs_pulse & 0x3f) | ((*cs_pulse & 0x100) >> 2);
-}
-
-static unsigned long calc_mck_cycles(unsigned long ns, unsigned long mck_hz)
-{
-	unsigned long mul;
-
-	/*
-	* cycles = x [nsec] * f [Hz] / 10^9 [ns in sec] =
-	*     x * (f / 1_000_000_000) =
-	*     x * ((f * 65536) / 1_000_000_000) / 65536 =
-	*     x * (((f / 10_000) * 65536) / 100_000) / 65536 =
-	*/
-
-	mul = (mck_hz / 10000) << 16;
-	mul /= 100000;
-
-	return (ns * mul + 65536) >> 16;    /* rounding */
-}
-
-/**
- * set_smc_timing - SMC timings setup.
- * @dev: device
- * @info: AT91 IDE info
- * @ata: ATA timings
- *
- * Its assumed that write timings are same as read timings,
- * cs_setup = 0 and cs_pulse = cycle.
- */
-static void set_smc_timing(struct device *dev, struct ata_device *adev,
-		struct at91_ide_info *info, const struct ata_timing *ata)
-{
-	int ret = 0;
-	int use_iordy;
-	unsigned int t6z;         /* data tristate time in ns */
-	unsigned int cycle;       /* SMC Cycle width in MCK ticks */
-	unsigned int setup;       /* SMC Setup width in MCK ticks */
-	unsigned int pulse;       /* CFIOR and CFIOW pulse width in MCK ticks */
-	unsigned int cs_pulse;    /* CS4 or CS5 pulse width in MCK ticks*/
-	unsigned int tdf_cycles;  /* SMC TDF MCK ticks */
-	unsigned long mck_hz;     /* MCK frequency in Hz */
-
-	t6z = (ata->mode < XFER_PIO_5) ? 30 : 20;
-	mck_hz = clk_get_rate(info->mck);
-	cycle = calc_mck_cycles(ata->cyc8b, mck_hz);
-	setup = calc_mck_cycles(ata->setup, mck_hz);
-	pulse = calc_mck_cycles(ata->act8b, mck_hz);
-	tdf_cycles = calc_mck_cycles(t6z, mck_hz);
-
-	do {
-		ret = calc_smc_vals(dev, &setup, &pulse, &cycle, &cs_pulse);
-	} while (ret == -ER_SMC_RECALC);
-
-	if (ret == -ER_SMC_CALC)
-		dev_err(dev, "Interface may not operate correctly\n");
-
-	dev_dbg(dev, "SMC Setup=%u, Pulse=%u, Cycle=%u, CS Pulse=%u\n",
-		setup, pulse, cycle, cs_pulse);
-	to_smc_format(&setup, &pulse, &cycle, &cs_pulse);
-	/* disable or enable waiting for IORDY signal */
-	use_iordy = ata_pio_need_iordy(adev);
-	if (use_iordy)
-		info->mode |= AT91_SMC_EXNWMODE_READY;
-
-	if (tdf_cycles > 15) {
-		tdf_cycles = 15;
-		dev_warn(dev, "maximal SMC TDF Cycles value\n");
-	}
-
-	dev_dbg(dev, "Use IORDY=%u, TDF Cycles=%u\n", use_iordy, tdf_cycles);
-
-	regmap_fields_write(fields.setup, info->cs,
-			    AT91SAM9_SMC_NRDSETUP(setup) |
-			    AT91SAM9_SMC_NWESETUP(setup) |
-			    AT91SAM9_SMC_NCS_NRDSETUP(0) |
-			    AT91SAM9_SMC_NCS_WRSETUP(0));
-	regmap_fields_write(fields.pulse, info->cs,
-			    AT91SAM9_SMC_NRDPULSE(pulse) |
-			    AT91SAM9_SMC_NWEPULSE(pulse) |
-			    AT91SAM9_SMC_NCS_NRDPULSE(cs_pulse) |
-			    AT91SAM9_SMC_NCS_WRPULSE(cs_pulse));
-	regmap_fields_write(fields.cycle, info->cs,
-			    AT91SAM9_SMC_NRDCYCLE(cycle) |
-			    AT91SAM9_SMC_NWECYCLE(cycle));
-	regmap_fields_write(fields.mode, info->cs, info->mode |
-			    AT91_SMC_TDF_(tdf_cycles));
-}
-
-static void pata_at91_set_piomode(struct ata_port *ap, struct ata_device *adev)
-{
-	struct at91_ide_info *info = ap->host->private_data;
-	struct ata_timing timing;
-	int ret;
-
-	/* Compute ATA timing and set it to SMC */
-	ret = ata_timing_compute(adev, adev->pio_mode, &timing, 1000, 0);
-	if (ret) {
-		dev_warn(ap->dev, "Failed to compute ATA timing %d, "
-			 "set PIO_0 timing\n", ret);
-		timing = *ata_timing_find_mode(XFER_PIO_0);
-	}
-	set_smc_timing(ap->dev, adev, info, &timing);
-}
-
-static unsigned int pata_at91_data_xfer_noirq(struct ata_queued_cmd *qc,
-		unsigned char *buf, unsigned int buflen, int rw)
-{
-	struct at91_ide_info *info = qc->dev->link->ap->host->private_data;
-	unsigned int consumed;
-	unsigned int mode;
-	unsigned long flags;
-
-	local_irq_save(flags);
-	regmap_fields_read(fields.mode, info->cs, &mode);
-
-	/* set 16bit mode before writing data */
-	regmap_fields_write(fields.mode, info->cs, (mode & ~AT91_SMC_DBW) |
-			    AT91_SMC_DBW_16);
-
-	consumed = ata_sff_data_xfer(qc, buf, buflen, rw);
-
-	/* restore 8bit mode after data is written */
-	regmap_fields_write(fields.mode, info->cs, (mode & ~AT91_SMC_DBW) |
-			    AT91_SMC_DBW_8);
-
-	local_irq_restore(flags);
-	return consumed;
-}
-
-static struct scsi_host_template pata_at91_sht = {
-	ATA_PIO_SHT(DRV_NAME),
-};
-
-static struct ata_port_operations pata_at91_port_ops = {
-	.inherits	= &ata_sff_port_ops,
-
-	.sff_data_xfer	= pata_at91_data_xfer_noirq,
-	.set_piomode	= pata_at91_set_piomode,
-	.cable_detect	= ata_cable_40wire,
-};
-
-static int at91sam9_smc_fields_init(struct device *dev)
-{
-	struct reg_field field = REG_FIELD(0, 0, 31);
-
-	field.id_size = 8;
-	field.id_offset = AT91SAM9_SMC_GENERIC_BLK_SZ;
-
-	field.reg = AT91SAM9_SMC_SETUP(AT91SAM9_SMC_GENERIC);
-	fields.setup = devm_regmap_field_alloc(dev, smc, field);
-	if (IS_ERR(fields.setup))
-		return PTR_ERR(fields.setup);
-
-	field.reg = AT91SAM9_SMC_PULSE(AT91SAM9_SMC_GENERIC);
-	fields.pulse = devm_regmap_field_alloc(dev, smc, field);
-	if (IS_ERR(fields.pulse))
-		return PTR_ERR(fields.pulse);
-
-	field.reg = AT91SAM9_SMC_CYCLE(AT91SAM9_SMC_GENERIC);
-	fields.cycle = devm_regmap_field_alloc(dev, smc, field);
-	if (IS_ERR(fields.cycle))
-		return PTR_ERR(fields.cycle);
-
-	field.reg = AT91SAM9_SMC_MODE(AT91SAM9_SMC_GENERIC);
-	fields.mode = devm_regmap_field_alloc(dev, smc, field);
-
-	return PTR_ERR_OR_ZERO(fields.mode);
-}
-
-static int pata_at91_probe(struct platform_device *pdev)
-{
-	struct at91_cf_data *board = dev_get_platdata(&pdev->dev);
-	struct device *dev = &pdev->dev;
-	struct at91_ide_info *info;
-	struct resource *mem_res;
-	struct ata_host *host;
-	struct ata_port *ap;
-
-	int irq_flags = 0;
-	int irq = 0;
-	int ret;
-
-	/*  get platform resources: IO/CTL memories and irq/rst pins */
-
-	if (pdev->num_resources != 1) {
-		dev_err(&pdev->dev, "invalid number of resources\n");
-		return -EINVAL;
-	}
-
-	mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-
-	if (!mem_res) {
-		dev_err(dev, "failed to get mem resource\n");
-		return -EINVAL;
-	}
-
-	irq = board->irq_pin;
-
-	smc = syscon_regmap_lookup_by_phandle(pdev->dev.of_node, "atmel,smc");
-	if (IS_ERR(smc))
-		return PTR_ERR(smc);
-
-	ret = at91sam9_smc_fields_init(dev);
-	if (ret < 0)
-		return ret;
-
-	/* init ata host */
-
-	host = ata_host_alloc(dev, 1);
-
-	if (!host)
-		return -ENOMEM;
-
-	ap = host->ports[0];
-	ap->ops = &pata_at91_port_ops;
-	ap->flags |= ATA_FLAG_SLAVE_POSS;
-	ap->pio_mask = ATA_PIO4;
-
-	if (!gpio_is_valid(irq)) {
-		ap->flags |= ATA_FLAG_PIO_POLLING;
-		ata_port_desc(ap, "no IRQ, using PIO polling");
-	}
-
-	info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
-
-	if (!info) {
-		dev_err(dev, "failed to allocate memory for private data\n");
-		return -ENOMEM;
-	}
-
-	info->mck = clk_get(NULL, "mck");
-
-	if (IS_ERR(info->mck)) {
-		dev_err(dev, "failed to get access to mck clock\n");
-		return -ENODEV;
-	}
-
-	info->cs    = board->chipselect;
-	info->mode  = AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
-		AT91_SMC_EXNWMODE_READY | AT91_SMC_BAT_SELECT |
-		AT91_SMC_DBW_8 | AT91_SMC_TDF_(0);
-
-	info->ide_addr = devm_ioremap(dev,
-			mem_res->start + CF_IDE_OFFSET, CF_IDE_RES_SIZE);
-
-	if (!info->ide_addr) {
-		dev_err(dev, "failed to map IO base\n");
-		ret = -ENOMEM;
-		goto err_put;
-	}
-
-	info->alt_addr = devm_ioremap(dev,
-			mem_res->start + CF_ALT_IDE_OFFSET, CF_IDE_RES_SIZE);
-
-	if (!info->alt_addr) {
-		dev_err(dev, "failed to map CTL base\n");
-		ret = -ENOMEM;
-		goto err_put;
-	}
-
-	ap->ioaddr.cmd_addr = info->ide_addr;
-	ap->ioaddr.ctl_addr = info->alt_addr + 0x06;
-	ap->ioaddr.altstatus_addr = ap->ioaddr.ctl_addr;
-
-	ata_sff_std_ports(&ap->ioaddr);
-
-	ata_port_desc(ap, "mmio cmd 0x%llx ctl 0x%llx",
-			(unsigned long long)mem_res->start + CF_IDE_OFFSET,
-			(unsigned long long)mem_res->start + CF_ALT_IDE_OFFSET);
-
-	host->private_data = info;
-
-	ret = ata_host_activate(host, gpio_is_valid(irq) ? gpio_to_irq(irq) : 0,
-				gpio_is_valid(irq) ? ata_sff_interrupt : NULL,
-				irq_flags, &pata_at91_sht);
-	if (ret)
-		goto err_put;
-
-	return 0;
-
-err_put:
-	clk_put(info->mck);
-	return ret;
-}
-
-static int pata_at91_remove(struct platform_device *pdev)
-{
-	struct ata_host *host = platform_get_drvdata(pdev);
-	struct at91_ide_info *info;
-
-	if (!host)
-		return 0;
-	info = host->private_data;
-
-	ata_host_detach(host);
-
-	if (!info)
-		return 0;
-
-	clk_put(info->mck);
-
-	return 0;
-}
-
-static struct platform_driver pata_at91_driver = {
-	.probe		= pata_at91_probe,
-	.remove		= pata_at91_remove,
-	.driver		= {
-		.name		= DRV_NAME,
-	},
-};
-
-module_platform_driver(pata_at91_driver);
-
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("Driver for CF in True IDE mode on AT91SAM9260 SoC");
-MODULE_AUTHOR("Matyukevich Sergey");
-MODULE_VERSION(DRV_VERSION);
-

drivers/ata/pata_macio.c

@@ -1328,7 +1328,7 @@ static int pata_macio_pci_resume(struct pci_dev *pdev)
 }
 #endif /* CONFIG_PM_SLEEP */
 
-static struct of_device_id pata_macio_match[] =
+static const struct of_device_id pata_macio_match[] =
 {
 	{
 	.name 		= "IDE",

drivers/ata/pata_mpc52xx.c

@@ -847,7 +847,7 @@ mpc52xx_ata_resume(struct platform_device *op)
 }
 #endif
 
-static struct of_device_id mpc52xx_ata_of_match[] = {
+static const struct of_device_id mpc52xx_ata_of_match[] = {
 	{ .compatible = "fsl,mpc5200-ata", },
 	{ .compatible = "mpc5200-ata", },
 	{},

drivers/ata/pata_of_platform.c

@@ -67,7 +67,7 @@ static int pata_of_platform_probe(struct platform_device *ofdev)
 				     reg_shift, pio_mask, &pata_platform_sht);
 }
 
-static struct of_device_id pata_of_platform_match[] = {
+static const struct of_device_id pata_of_platform_match[] = {
 	{ .compatible = "ata-generic", },
 	{ },
 };

drivers/ata/sata_fsl.c

@@ -1612,7 +1612,7 @@ static int sata_fsl_resume(struct platform_device *op)
 }
 #endif
 
-static struct of_device_id fsl_sata_match[] = {
+static const struct of_device_id fsl_sata_match[] = {
 	{
 		.compatible = "fsl,pq-sata",
 	},

drivers/ata/sata_mv.c

@@ -4286,7 +4286,7 @@ static int mv_platform_resume(struct platform_device *pdev)
 #endif
 
 #ifdef CONFIG_OF
-static struct of_device_id mv_sata_dt_ids[] = {
+static const struct of_device_id mv_sata_dt_ids[] = {
 	{ .compatible = "marvell,armada-370-sata", },
 	{ .compatible = "marvell,orion-sata", },
 	{},

include/linux/ata.h

@@ -817,11 +817,6 @@ static inline bool ata_id_sct_error_recovery_ctrl(const u16 *id)
 	return id[ATA_ID_SCT_CMD_XPORT] & (1 << 3) ? true : false;
 }
 
-static inline bool ata_id_sct_write_same(const u16 *id)
-{
-	return id[ATA_ID_SCT_CMD_XPORT] & (1 << 2) ? true : false;
-}
-
 static inline bool ata_id_sct_long_sector_access(const u16 *id)
 {
 	return id[ATA_ID_SCT_CMD_XPORT] & (1 << 1) ? true : false;