Commit e88b815e authored by Xianglong Du's avatar Xianglong Du Committed by Linus Torvalds

drivers/rtc/rtc-sirfsoc.c: add rtc drivers for CSR SiRFprimaII and SiRFatlasVI

On CSR SiRFprimaII/atlasVI, there is a programmable 16-bit divider
(RTC_DIV) that divides the input 32.768KHz clock to the frequency that
users need (E.g.  1 Hz).  The divided real-time clock will be used to
drive a 32-bit counter (RTC_COUNTER) that provides users with the actual
time.

In each cycle of the divided real-time clock, there is a Hertz interrupt
generated to the RISC.  Users can also configure an alarm (RTC_ALARM).
When RTC_COUNTER matches the alarm, there will be an alarm interrupt
generated to the RISC.

The system RTC can generate an alarm wake-up signal to notify the power
controller to wake up from power saving mode.
Signed-off-by: default avatarXianglong Du <Xianglong.Du@csr.com>
Signed-off-by: default avatarBarry Song <Baohua.Song@csr.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
parent 061d2a3e
......@@ -613,7 +613,7 @@ rom-interface@57a00000 {
};
rtc-iobg {
compatible = "sirf,prima2-rtciobg", "sirf-prima2-rtciobg-bus";
compatible = "sirf,prima2-rtciobg", "sirf-prima2-rtciobg-bus", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
reg = <0x80030000 0x10000>;
......
......@@ -610,7 +610,7 @@ rom-interface@57a00000 {
};
rtc-iobg {
compatible = "sirf,prima2-rtciobg", "sirf-prima2-rtciobg-bus";
compatible = "sirf,prima2-rtciobg", "sirf-prima2-rtciobg-bus", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
reg = <0x80030000 0x10000>;
......
......@@ -1242,6 +1242,13 @@ config RTC_DRV_SNVS
This driver can also be built as a module, if so, the module
will be called "rtc-snvs".
config RTC_DRV_SIRFSOC
tristate "SiRFSOC RTC"
depends on ARCH_SIRF
help
Say "yes" here to support the real time clock on SiRF SOC chips.
This driver can also be built as a module called rtc-sirfsoc.
comment "HID Sensor RTC drivers"
config RTC_DRV_HID_SENSOR_TIME
......
......@@ -129,3 +129,4 @@ obj-$(CONFIG_RTC_DRV_VT8500) += rtc-vt8500.o
obj-$(CONFIG_RTC_DRV_WM831X) += rtc-wm831x.o
obj-$(CONFIG_RTC_DRV_WM8350) += rtc-wm8350.o
obj-$(CONFIG_RTC_DRV_X1205) += rtc-x1205.o
obj-$(CONFIG_RTC_DRV_SIRFSOC) += rtc-sirfsoc.o
/*
* SiRFSoC Real Time Clock interface for Linux
*
* Copyright (c) 2013 Cambridge Silicon Radio Limited, a CSR plc group company.
*
* Licensed under GPLv2 or later.
*/
#include <linux/module.h>
#include <linux/err.h>
#include <linux/rtc.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/io.h>
#include <linux/of.h>
#include <linux/rtc/sirfsoc_rtciobrg.h>
#define RTC_CN 0x00
#define RTC_ALARM0 0x04
#define RTC_ALARM1 0x18
#define RTC_STATUS 0x08
#define RTC_SW_VALUE 0x40
#define SIRFSOC_RTC_AL1E (1<<6)
#define SIRFSOC_RTC_AL1 (1<<4)
#define SIRFSOC_RTC_HZE (1<<3)
#define SIRFSOC_RTC_AL0E (1<<2)
#define SIRFSOC_RTC_HZ (1<<1)
#define SIRFSOC_RTC_AL0 (1<<0)
#define RTC_DIV 0x0c
#define RTC_DEEP_CTRL 0x14
#define RTC_CLOCK_SWITCH 0x1c
#define SIRFSOC_RTC_CLK 0x03 /* others are reserved */
/* Refer to RTC DIV switch */
#define RTC_HZ 16
/* This macro is also defined in arch/arm/plat-sirfsoc/cpu.c */
#define RTC_SHIFT 4
#define INTR_SYSRTC_CN 0x48
struct sirfsoc_rtc_drv {
struct rtc_device *rtc;
u32 rtc_base;
u32 irq;
/* Overflow for every 8 years extra time */
u32 overflow_rtc;
#ifdef CONFIG_PM
u32 saved_counter;
u32 saved_overflow_rtc;
#endif
};
static int sirfsoc_rtc_read_alarm(struct device *dev,
struct rtc_wkalrm *alrm)
{
unsigned long rtc_alarm, rtc_count;
struct sirfsoc_rtc_drv *rtcdrv;
rtcdrv = (struct sirfsoc_rtc_drv *)dev_get_drvdata(dev);
local_irq_disable();
rtc_count = sirfsoc_rtc_iobrg_readl(rtcdrv->rtc_base + RTC_CN);
rtc_alarm = sirfsoc_rtc_iobrg_readl(rtcdrv->rtc_base + RTC_ALARM0);
memset(alrm, 0, sizeof(struct rtc_wkalrm));
/*
* assume alarm interval not beyond one round counter overflow_rtc:
* 0->0xffffffff
*/
/* if alarm is in next overflow cycle */
if (rtc_count > rtc_alarm)
rtc_time_to_tm((rtcdrv->overflow_rtc + 1)
<< (BITS_PER_LONG - RTC_SHIFT)
| rtc_alarm >> RTC_SHIFT, &(alrm->time));
else
rtc_time_to_tm(rtcdrv->overflow_rtc
<< (BITS_PER_LONG - RTC_SHIFT)
| rtc_alarm >> RTC_SHIFT, &(alrm->time));
if (sirfsoc_rtc_iobrg_readl(
rtcdrv->rtc_base + RTC_STATUS) & SIRFSOC_RTC_AL0E)
alrm->enabled = 1;
local_irq_enable();
return 0;
}
static int sirfsoc_rtc_set_alarm(struct device *dev,
struct rtc_wkalrm *alrm)
{
unsigned long rtc_status_reg, rtc_alarm;
struct sirfsoc_rtc_drv *rtcdrv;
rtcdrv = (struct sirfsoc_rtc_drv *)dev_get_drvdata(dev);
if (alrm->enabled) {
rtc_tm_to_time(&(alrm->time), &rtc_alarm);
local_irq_disable();
rtc_status_reg = sirfsoc_rtc_iobrg_readl(
rtcdrv->rtc_base + RTC_STATUS);
if (rtc_status_reg & SIRFSOC_RTC_AL0E) {
/*
* An ongoing alarm in progress - ingore it and not
* to return EBUSY
*/
dev_info(dev, "An old alarm was set, will be replaced by a new one\n");
}
sirfsoc_rtc_iobrg_writel(
rtc_alarm << RTC_SHIFT, rtcdrv->rtc_base + RTC_ALARM0);
rtc_status_reg &= ~0x07; /* mask out the lower status bits */
/*
* This bit RTC_AL sets it as a wake-up source for Sleep Mode
* Writing 1 into this bit will clear it
*/
rtc_status_reg |= SIRFSOC_RTC_AL0;
/* enable the RTC alarm interrupt */
rtc_status_reg |= SIRFSOC_RTC_AL0E;
sirfsoc_rtc_iobrg_writel(
rtc_status_reg, rtcdrv->rtc_base + RTC_STATUS);
local_irq_enable();
} else {
/*
* if this function was called with enabled=0
* then it could mean that the application is
* trying to cancel an ongoing alarm
*/
local_irq_disable();
rtc_status_reg = sirfsoc_rtc_iobrg_readl(
rtcdrv->rtc_base + RTC_STATUS);
if (rtc_status_reg & SIRFSOC_RTC_AL0E) {
/* clear the RTC status register's alarm bit */
rtc_status_reg &= ~0x07;
/* write 1 into SIRFSOC_RTC_AL0 to force a clear */
rtc_status_reg |= (SIRFSOC_RTC_AL0);
/* Clear the Alarm enable bit */
rtc_status_reg &= ~(SIRFSOC_RTC_AL0E);
sirfsoc_rtc_iobrg_writel(rtc_status_reg,
rtcdrv->rtc_base + RTC_STATUS);
}
local_irq_enable();
}
return 0;
}
static int sirfsoc_rtc_read_time(struct device *dev,
struct rtc_time *tm)
{
unsigned long tmp_rtc = 0;
struct sirfsoc_rtc_drv *rtcdrv;
rtcdrv = (struct sirfsoc_rtc_drv *)dev_get_drvdata(dev);
/*
* This patch is taken from WinCE - Need to validate this for
* correctness. To work around sirfsoc RTC counter double sync logic
* fail, read several times to make sure get stable value.
*/
do {
tmp_rtc = sirfsoc_rtc_iobrg_readl(rtcdrv->rtc_base + RTC_CN);
cpu_relax();
} while (tmp_rtc != sirfsoc_rtc_iobrg_readl(rtcdrv->rtc_base + RTC_CN));
rtc_time_to_tm(rtcdrv->overflow_rtc << (BITS_PER_LONG - RTC_SHIFT) |
tmp_rtc >> RTC_SHIFT, tm);
return 0;
}
static int sirfsoc_rtc_set_time(struct device *dev,
struct rtc_time *tm)
{
unsigned long rtc_time;
struct sirfsoc_rtc_drv *rtcdrv;
rtcdrv = (struct sirfsoc_rtc_drv *)dev_get_drvdata(dev);
rtc_tm_to_time(tm, &rtc_time);
rtcdrv->overflow_rtc = rtc_time >> (BITS_PER_LONG - RTC_SHIFT);
sirfsoc_rtc_iobrg_writel(rtcdrv->overflow_rtc,
rtcdrv->rtc_base + RTC_SW_VALUE);
sirfsoc_rtc_iobrg_writel(
rtc_time << RTC_SHIFT, rtcdrv->rtc_base + RTC_CN);
return 0;
}
static int sirfsoc_rtc_ioctl(struct device *dev, unsigned int cmd,
unsigned long arg)
{
switch (cmd) {
case RTC_PIE_ON:
case RTC_PIE_OFF:
case RTC_UIE_ON:
case RTC_UIE_OFF:
case RTC_AIE_ON:
case RTC_AIE_OFF:
return 0;
default:
return -ENOIOCTLCMD;
}
}
static const struct rtc_class_ops sirfsoc_rtc_ops = {
.read_time = sirfsoc_rtc_read_time,
.set_time = sirfsoc_rtc_set_time,
.read_alarm = sirfsoc_rtc_read_alarm,
.set_alarm = sirfsoc_rtc_set_alarm,
.ioctl = sirfsoc_rtc_ioctl
};
static irqreturn_t sirfsoc_rtc_irq_handler(int irq, void *pdata)
{
struct sirfsoc_rtc_drv *rtcdrv = pdata;
unsigned long rtc_status_reg = 0x0;
unsigned long events = 0x0;
rtc_status_reg = sirfsoc_rtc_iobrg_readl(rtcdrv->rtc_base + RTC_STATUS);
/* this bit will be set ONLY if an alarm was active
* and it expired NOW
* So this is being used as an ASSERT
*/
if (rtc_status_reg & SIRFSOC_RTC_AL0) {
/*
* clear the RTC status register's alarm bit
* mask out the lower status bits
*/
rtc_status_reg &= ~0x07;
/* write 1 into SIRFSOC_RTC_AL0 to ACK the alarm interrupt */
rtc_status_reg |= (SIRFSOC_RTC_AL0);
/* Clear the Alarm enable bit */
rtc_status_reg &= ~(SIRFSOC_RTC_AL0E);
}
sirfsoc_rtc_iobrg_writel(rtc_status_reg, rtcdrv->rtc_base + RTC_STATUS);
/* this should wake up any apps polling/waiting on the read
* after setting the alarm
*/
events |= RTC_IRQF | RTC_AF;
rtc_update_irq(rtcdrv->rtc, 1, events);
return IRQ_HANDLED;
}
static const struct of_device_id sirfsoc_rtc_of_match[] = {
{ .compatible = "sirf,prima2-sysrtc"},
{},
};
MODULE_DEVICE_TABLE(of, sirfsoc_rtc_of_match);
static int sirfsoc_rtc_probe(struct platform_device *pdev)
{
int err;
unsigned long rtc_div;
struct sirfsoc_rtc_drv *rtcdrv;
struct device_node *np = pdev->dev.of_node;
rtcdrv = devm_kzalloc(&pdev->dev,
sizeof(struct sirfsoc_rtc_drv), GFP_KERNEL);
if (rtcdrv == NULL) {
dev_err(&pdev->dev,
"%s: can't alloc mem for drv struct\n",
pdev->name);
return -ENOMEM;
}
err = of_property_read_u32(np, "reg", &rtcdrv->rtc_base);
if (err) {
dev_err(&pdev->dev, "unable to find base address of rtc node in dtb\n");
goto error;
}
platform_set_drvdata(pdev, rtcdrv);
/* Register rtc alarm as a wakeup source */
device_init_wakeup(&pdev->dev, 1);
/*
* Set SYS_RTC counter in RTC_HZ HZ Units
* We are using 32K RTC crystal (32768 / RTC_HZ / 2) -1
* If 16HZ, therefore RTC_DIV = 1023;
*/
rtc_div = ((32768 / RTC_HZ) / 2) - 1;
sirfsoc_rtc_iobrg_writel(rtc_div, rtcdrv->rtc_base + RTC_DIV);
rtcdrv->rtc = rtc_device_register(pdev->name, &(pdev->dev),
&sirfsoc_rtc_ops, THIS_MODULE);
if (IS_ERR(rtcdrv->rtc)) {
err = PTR_ERR(rtcdrv->rtc);
dev_err(&pdev->dev, "can't register RTC device\n");
return err;
}
/* 0x3 -> RTC_CLK */
sirfsoc_rtc_iobrg_writel(SIRFSOC_RTC_CLK,
rtcdrv->rtc_base + RTC_CLOCK_SWITCH);
/* reset SYS RTC ALARM0 */
sirfsoc_rtc_iobrg_writel(0x0, rtcdrv->rtc_base + RTC_ALARM0);
/* reset SYS RTC ALARM1 */
sirfsoc_rtc_iobrg_writel(0x0, rtcdrv->rtc_base + RTC_ALARM1);
/* Restore RTC Overflow From Register After Command Reboot */
rtcdrv->overflow_rtc =
sirfsoc_rtc_iobrg_readl(rtcdrv->rtc_base + RTC_SW_VALUE);
rtcdrv->irq = platform_get_irq(pdev, 0);
err = devm_request_irq(
&pdev->dev,
rtcdrv->irq,
sirfsoc_rtc_irq_handler,
IRQF_SHARED,
pdev->name,
rtcdrv);
if (err) {
dev_err(&pdev->dev, "Unable to register for the SiRF SOC RTC IRQ\n");
goto error;
}
return 0;
error:
if (rtcdrv->rtc)
rtc_device_unregister(rtcdrv->rtc);
return err;
}
static int sirfsoc_rtc_remove(struct platform_device *pdev)
{
struct sirfsoc_rtc_drv *rtcdrv = platform_get_drvdata(pdev);
device_init_wakeup(&pdev->dev, 0);
rtc_device_unregister(rtcdrv->rtc);
return 0;
}
#ifdef CONFIG_PM
static int sirfsoc_rtc_suspend(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
struct sirfsoc_rtc_drv *rtcdrv = platform_get_drvdata(pdev);
rtcdrv->overflow_rtc =
sirfsoc_rtc_iobrg_readl(rtcdrv->rtc_base + RTC_SW_VALUE);
rtcdrv->saved_counter =
sirfsoc_rtc_iobrg_readl(rtcdrv->rtc_base + RTC_CN);
rtcdrv->saved_overflow_rtc = rtcdrv->overflow_rtc;
if (device_may_wakeup(&pdev->dev))
enable_irq_wake(rtcdrv->irq);
return 0;
}
static int sirfsoc_rtc_freeze(struct device *dev)
{
sirfsoc_rtc_suspend(dev);
return 0;
}
static int sirfsoc_rtc_thaw(struct device *dev)
{
u32 tmp;
struct sirfsoc_rtc_drv *rtcdrv;
rtcdrv = (struct sirfsoc_rtc_drv *)dev_get_drvdata(dev);
/*
* if resume from snapshot and the rtc power is losed,
* restroe the rtc settings
*/
if (SIRFSOC_RTC_CLK != sirfsoc_rtc_iobrg_readl(
rtcdrv->rtc_base + RTC_CLOCK_SWITCH)) {
u32 rtc_div;
/* 0x3 -> RTC_CLK */
sirfsoc_rtc_iobrg_writel(SIRFSOC_RTC_CLK,
rtcdrv->rtc_base + RTC_CLOCK_SWITCH);
/*
* Set SYS_RTC counter in RTC_HZ HZ Units
* We are using 32K RTC crystal (32768 / RTC_HZ / 2) -1
* If 16HZ, therefore RTC_DIV = 1023;
*/
rtc_div = ((32768 / RTC_HZ) / 2) - 1;
sirfsoc_rtc_iobrg_writel(rtc_div, rtcdrv->rtc_base + RTC_DIV);
/* reset SYS RTC ALARM0 */
sirfsoc_rtc_iobrg_writel(0x0, rtcdrv->rtc_base + RTC_ALARM0);
/* reset SYS RTC ALARM1 */
sirfsoc_rtc_iobrg_writel(0x0, rtcdrv->rtc_base + RTC_ALARM1);
}
rtcdrv->overflow_rtc = rtcdrv->saved_overflow_rtc;
/*
* if current counter is small than previous,
* it means overflow in sleep
*/
tmp = sirfsoc_rtc_iobrg_readl(rtcdrv->rtc_base + RTC_CN);
if (tmp <= rtcdrv->saved_counter)
rtcdrv->overflow_rtc++;
/*
*PWRC Value Be Changed When Suspend, Restore Overflow
* In Memory To Register
*/
sirfsoc_rtc_iobrg_writel(rtcdrv->overflow_rtc,
rtcdrv->rtc_base + RTC_SW_VALUE);
return 0;
}
static int sirfsoc_rtc_resume(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
struct sirfsoc_rtc_drv *rtcdrv = platform_get_drvdata(pdev);
sirfsoc_rtc_thaw(dev);
if (device_may_wakeup(&pdev->dev))
disable_irq_wake(rtcdrv->irq);
return 0;
}
static int sirfsoc_rtc_restore(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
struct sirfsoc_rtc_drv *rtcdrv = platform_get_drvdata(pdev);
if (device_may_wakeup(&pdev->dev))
disable_irq_wake(rtcdrv->irq);
return 0;
}
#else
#define sirfsoc_rtc_suspend NULL
#define sirfsoc_rtc_resume NULL
#define sirfsoc_rtc_freeze NULL
#define sirfsoc_rtc_thaw NULL
#define sirfsoc_rtc_restore NULL
#endif
static const struct dev_pm_ops sirfsoc_rtc_pm_ops = {
.suspend = sirfsoc_rtc_suspend,
.resume = sirfsoc_rtc_resume,
.freeze = sirfsoc_rtc_freeze,
.thaw = sirfsoc_rtc_thaw,
.restore = sirfsoc_rtc_restore,
};
static struct platform_driver sirfsoc_rtc_driver = {
.driver = {
.name = "sirfsoc-rtc",
.owner = THIS_MODULE,
#ifdef CONFIG_PM
.pm = &sirfsoc_rtc_pm_ops,
#endif
.of_match_table = of_match_ptr(sirfsoc_rtc_of_match),
},
.probe = sirfsoc_rtc_probe,
.remove = sirfsoc_rtc_remove,
};
module_platform_driver(sirfsoc_rtc_driver);
MODULE_DESCRIPTION("SiRF SoC rtc driver");
MODULE_AUTHOR("Xianglong Du <Xianglong.Du@csr.com>");
MODULE_LICENSE("GPL v2");
MODULE_ALIAS("platform:sirfsoc-rtc");
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment