[SCSI] qla4xxx: Modified debug log messages for boot info.

In some configurations user may not have boot targets configured.
In such cases the debug messages printed out by driver look like
some kind of failure happening. However this could be a valid
case, so modified the messages to appear as warning messages
versus failure messages.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

drivers/scsi/qla4xxx/ql4_os.c

@@ -3393,9 +3393,8 @@ static int get_fw_boot_info(struct scsi_qla_host *ha, uint16_t ddb_index[])
 		/* Check Boot Mode */
 		val = rd_nvram_byte(ha, addr);
 		if (!(val & 0x07)) {
-			DEBUG2(ql4_printk(KERN_ERR, ha,
-					  "%s: Failed Boot options : 0x%x\n",
-					  __func__, val));
+			DEBUG2(ql4_printk(KERN_INFO, ha, "%s: Adapter boot "
+					  "options : 0x%x\n", __func__, val));
 			ret = QLA_ERROR;
 			goto exit_boot_info;
 		}
@@ -3440,9 +3439,8 @@ static int get_fw_boot_info(struct scsi_qla_host *ha, uint16_t ddb_index[])
 		}
 		/* Check Boot Mode */
 		if (!(buf[1] & 0x07)) {
-			DEBUG2(ql4_printk(KERN_INFO, ha,
-					  "Failed: Boot options : 0x%x\n",
-					  buf[1]));
+			DEBUG2(ql4_printk(KERN_INFO, ha, "Firmware boot options"
+					  " : 0x%x\n", buf[1]));
 			ret = QLA_ERROR;
 			goto exit_boot_info_free;
 		}
@@ -3548,8 +3546,8 @@ static int qla4xxx_get_boot_target(struct scsi_qla_host *ha,
 
 	if (qla4xxx_bootdb_by_index(ha, fw_ddb_entry,
 				   fw_ddb_entry_dma, ddb_index)) {
-		DEBUG2(ql4_printk(KERN_ERR, ha,
-				  "%s: Flash DDB read Failed\n", __func__));
+		DEBUG2(ql4_printk(KERN_INFO, ha, "%s: No Flash DDB found at "
+				  "index [%d]\n", __func__, ddb_index));
 		ret = QLA_ERROR;
 		goto exit_boot_target;
 	}
@@ -3627,8 +3625,8 @@ static int qla4xxx_get_boot_info(struct scsi_qla_host *ha)
 	ddb_index[1] = 0xffff;
 	ret = get_fw_boot_info(ha, ddb_index);
 	if (ret != QLA_SUCCESS) {
-		DEBUG2(ql4_printk(KERN_ERR, ha,
-				  "%s: Failed to set boot info.\n", __func__));
+		DEBUG2(ql4_printk(KERN_INFO, ha,
+				"%s: No boot target configured.\n", __func__));
 		return ret;
 	}
 
@@ -3641,8 +3639,8 @@ static int qla4xxx_get_boot_info(struct scsi_qla_host *ha)
 	rval = qla4xxx_get_boot_target(ha, &(ha->boot_tgt.boot_pri_sess),
 				      ddb_index[0]);
 	if (rval != QLA_SUCCESS) {
-		DEBUG2(ql4_printk(KERN_ERR, ha, "%s: Failed to get "
-				  "primary target\n", __func__));
+		DEBUG2(ql4_printk(KERN_INFO, ha, "%s: Primary boot target not "
+				  "configured\n", __func__));
 	} else
 		ret = QLA_SUCCESS;
 
@@ -3653,8 +3651,8 @@ static int qla4xxx_get_boot_info(struct scsi_qla_host *ha)
 	rval = qla4xxx_get_boot_target(ha, &(ha->boot_tgt.boot_sec_sess),
 				      ddb_index[1]);
 	if (rval != QLA_SUCCESS) {
-		DEBUG2(ql4_printk(KERN_ERR, ha, "%s: Failed to get "
-				  "secondary target\n", __func__));
+		DEBUG2(ql4_printk(KERN_INFO, ha, "%s: Secondary boot target not"
+				  " configured\n", __func__));
 	} else
 		ret = QLA_SUCCESS;