Commit ea8817b1 authored by Rostislav Lisovy's avatar Rostislav Lisovy Committed by Shawn Guo

ARM: dts: i.MX53: dts for Voipac x53-dmm-668 module

Enable uart1, ecspi1, i2c1, FEC and PMIC
Signed-off-by: default avatarRostislav Lisovy <lisovy@gmail.com>
Signed-off-by: default avatarShawn Guo <shawn.guo@linaro.org>
parent 6f653a9f
/*
* Copyright 2013 Rostislav Lisovy <lisovy@gmail.com>, PiKRON s.r.o.
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
#include "imx53.dtsi"
/ {
model = "Voipac i.MX53 X53-DMM-668";
compatible = "voipac,imx53-dmm-668", "fsl,imx53";
memory@70000000 {
device_type = "memory";
reg = <0x70000000 0x20000000>;
};
memory@b0000000 {
device_type = "memory";
reg = <0xb0000000 0x20000000>;
};
regulators {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <0>;
reg_3p3v: regulator@0 {
compatible = "regulator-fixed";
reg = <0>;
regulator-name = "3P3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
reg_usb_vbus: regulator@1 {
compatible = "regulator-fixed";
reg = <1>;
regulator-name = "usb_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio3 31 0>; /* PEN */
enable-active-high;
};
};
};
&iomuxc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_hog>;
imx53-voipac {
pinctrl_hog: hoggrp {
fsl,pins = <
/* Make DA9053 regulator functional */
MX53_PAD_GPIO_16__GPIO7_11 0x80000000
/* FEC Power enable */
MX53_PAD_GPIO_11__GPIO4_1 0x80000000
/* FEC RST */
MX53_PAD_GPIO_12__GPIO4_2 0x80000000
>;
};
pinctrl_ecspi1: ecspi1grp {
fsl,pins = <
MX53_PAD_EIM_D16__ECSPI1_SCLK 0x80000000
MX53_PAD_EIM_D17__ECSPI1_MISO 0x80000000
MX53_PAD_EIM_D18__ECSPI1_MOSI 0x80000000
>;
};
pinctrl_fec: fecgrp {
fsl,pins = <
MX53_PAD_FEC_MDC__FEC_MDC 0x80000000
MX53_PAD_FEC_MDIO__FEC_MDIO 0x80000000
MX53_PAD_FEC_REF_CLK__FEC_TX_CLK 0x80000000
MX53_PAD_FEC_RX_ER__FEC_RX_ER 0x80000000
MX53_PAD_FEC_CRS_DV__FEC_RX_DV 0x80000000
MX53_PAD_FEC_RXD1__FEC_RDATA_1 0x80000000
MX53_PAD_FEC_RXD0__FEC_RDATA_0 0x80000000
MX53_PAD_FEC_TX_EN__FEC_TX_EN 0x80000000
MX53_PAD_FEC_TXD1__FEC_TDATA_1 0x80000000
MX53_PAD_FEC_TXD0__FEC_TDATA_0 0x80000000
>;
};
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX53_PAD_EIM_D21__I2C1_SCL 0xc0000000
MX53_PAD_EIM_D28__I2C1_SDA 0xc0000000
>;
};
pinctrl_uart1: uart1grp {
fsl,pins = <
MX53_PAD_PATA_DIOW__UART1_TXD_MUX 0x1e4
MX53_PAD_PATA_DMACK__UART1_RXD_MUX 0x1e4
>;
};
pinctrl_nand: nandgrp {
fsl,pins = <
MX53_PAD_NANDF_WE_B__EMI_NANDF_WE_B 0x4
MX53_PAD_NANDF_RE_B__EMI_NANDF_RE_B 0x4
MX53_PAD_NANDF_CLE__EMI_NANDF_CLE 0x4
MX53_PAD_NANDF_ALE__EMI_NANDF_ALE 0x4
MX53_PAD_NANDF_WP_B__EMI_NANDF_WP_B 0xe0
MX53_PAD_NANDF_RB0__EMI_NANDF_RB_0 0xe0
MX53_PAD_NANDF_CS0__EMI_NANDF_CS_0 0x4
MX53_PAD_PATA_DATA0__EMI_NANDF_D_0 0xa4
MX53_PAD_PATA_DATA1__EMI_NANDF_D_1 0xa4
MX53_PAD_PATA_DATA2__EMI_NANDF_D_2 0xa4
MX53_PAD_PATA_DATA3__EMI_NANDF_D_3 0xa4
MX53_PAD_PATA_DATA4__EMI_NANDF_D_4 0xa4
MX53_PAD_PATA_DATA5__EMI_NANDF_D_5 0xa4
MX53_PAD_PATA_DATA6__EMI_NANDF_D_6 0xa4
MX53_PAD_PATA_DATA7__EMI_NANDF_D_7 0xa4
>;
};
};
};
&ecspi1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi1>;
fsl,spi-num-chipselects = <4>;
cs-gpios = <&gpio2 30 0>, <&gpio3 19 0>, <&gpio2 16 0>, <&gpio2 17 0>;
status = "okay";
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_fec>;
phy-mode = "rmii";
phy-reset-gpios = <&gpio4 2 0>;
status = "okay";
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1>;
status = "okay";
pmic: dialog@48 {
compatible = "dlg,da9053-aa", "dlg,da9052";
reg = <0x48>;
interrupt-parent = <&gpio7>;
interrupts = <11 0x8>; /* low-level active IRQ at GPIO7_11 */
regulators {
buck1_reg: buck1 {
regulator-name = "BUCKCORE";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1400000>;
regulator-always-on;
};
buck2_reg: buck2 {
regulator-name = "BUCKPRO";
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
};
buck3_reg: buck3 {
regulator-name = "BUCKMEM";
regulator-min-microvolt = <1420000>;
regulator-max-microvolt = <1580000>;
regulator-always-on;
};
buck4_reg: buck4 {
regulator-name = "BUCKPERI";
regulator-min-microvolt = <2370000>;
regulator-max-microvolt = <2630000>;
regulator-always-on;
};
ldo1_reg: ldo1 {
regulator-name = "ldo1_1v3";
regulator-min-microvolt = <1250000>;
regulator-max-microvolt = <1350000>;
regulator-boot-on;
regulator-always-on;
};
ldo2_reg: ldo2 {
regulator-name = "ldo2_1v3";
regulator-min-microvolt = <1250000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
};
ldo3_reg: ldo3 {
regulator-name = "ldo3_3v3";
regulator-min-microvolt = <3250000>;
regulator-max-microvolt = <3350000>;
regulator-always-on;
};
ldo4_reg: ldo4 {
regulator-name = "ldo4_2v775";
regulator-min-microvolt = <2770000>;
regulator-max-microvolt = <2780000>;
regulator-always-on;
};
ldo5_reg: ldo5 {
regulator-name = "ldo5_3v3";
regulator-min-microvolt = <3250000>;
regulator-max-microvolt = <3350000>;
regulator-always-on;
};
ldo6_reg: ldo6 {
regulator-name = "ldo6_1v3";
regulator-min-microvolt = <1250000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
};
ldo7_reg: ldo7 {
regulator-name = "ldo7_2v75";
regulator-min-microvolt = <2700000>;
regulator-max-microvolt = <2800000>;
regulator-always-on;
};
ldo8_reg: ldo8 {
regulator-name = "ldo8_1v8";
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <1850000>;
regulator-always-on;
};
ldo9_reg: ldo9 {
regulator-name = "ldo9_1v5";
regulator-min-microvolt = <1450000>;
regulator-max-microvolt = <1550000>;
regulator-always-on;
};
ldo10_reg: ldo10 {
regulator-name = "ldo10_1v3";
regulator-min-microvolt = <1250000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
};
};
};
};
&nfc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_nand>;
nand-bus-width = <8>;
nand-ecc-mode = "hw";
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
};
&usbh1 {
vbus-supply = <&reg_usb_vbus>;
phy_type = "utmi";
status = "okay";
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment