Merge tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc

Pull MMC update from Chris Ball:
 "MMC highlights for 3.9:

  Core:
   - Support for packed commands in eMMC 4.5.  (This requires a host
     capability to be turned on.  It increases write throughput by 20%+,
     but may also increase average write latency; more testing needed.)
   - Add DT bindings for capability flags.
   - Add mmc_of_parse() for shared DT parsing between drivers.

  Drivers:
   - android-goldfish: New MMC driver for the Android Goldfish emulator.
   - mvsdio: Add DT bindings, pinctrl, use slot-gpio for card detection.
   - omap_hsmmc: Fix boot hangs with RPMB partitions.
   - sdhci-bcm2835: New driver for controller used by Raspberry Pi.
   - sdhci-esdhc-imx: Add 8-bit data, auto CMD23 support, use slot-gpio.
   - sh_mmcif: Add support for eMMC DDR, bundled MMCIF IRQs.
   - tmio_mmc: Add DT bindings, support for vccq regulator"

* tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (92 commits)
  mmc: tegra: assume CONFIG_OF, remove platform data
  mmc: add DT bindings for more MMC capability flags
  mmc: tmio: add support for the VccQ regulator
  mmc: tmio: remove unused and deprecated symbols
  mmc: sh_mobile_sdhi: use managed resource allocations
  mmc: sh_mobile_sdhi: remove unused .pdata field
  mmc: tmio-mmc: parse device-tree bindings
  mmc: tmio-mmc: define device-tree bindings
  mmc: sh_mmcif: use mmc_of_parse() to parse standard MMC DT bindings
  mmc: (cosmetic) remove "extern" from function declarations
  mmc: provide a standard MMC device-tree binding parser centrally
  mmc: detailed definition of CD and WP MMC line polarities in DT
  mmc: sdhi, tmio: only check flags in tmio-mmc driver proper
  mmc: sdhci: Fix parameter of sdhci_do_start_signal_voltage_switch()
  mmc: sdhci: check voltage range only on regulators aware of voltage value
  mmc: bcm2835: set SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK
  mmc: support packed write command for eMMC4.5 devices
  mmc: add packed command feature of eMMC4.5
  mmc: rtsx: remove driving adjustment
  mmc: use regulator_can_change_voltage() instead of regulator_count_voltages
  ...

Documentation/devicetree/bindings/mmc/brcm,bcm2835-sdhci.txt

+Broadcom BCM2835 SDHCI controller
+
+This file documents differences between the core properties described
+by mmc.txt and the properties that represent the BCM2835 controller.
+
+Required properties:
+- compatible : Should be "brcm,bcm2835-sdhci".
+- clocks : The clock feeding the SDHCI controller.
+
+Example:
+
+sdhci: sdhci {
+	compatible = "brcm,bcm2835-sdhci";
+	reg = <0x7e300000 0x100>;
+	interrupts = <2 30>;
+	clocks = <&clk_mmc>;
+	bus-width = <4>;
+};

Documentation/devicetree/bindings/mmc/mmc.txt

@@ -6,23 +6,45 @@ Interpreted by the OF core:
 - reg: Registers location and length.
 - interrupts: Interrupts used by the MMC controller.
 
-Required properties:
-- bus-width: Number of data lines, can be <1>, <4>, or <8>
-
 Card detection:
-If no property below is supplied, standard SDHCI card detect is used.
+If no property below is supplied, host native card detect is used.
 Only one of the properties in this section should be supplied:
   - broken-cd: There is no card detection available; polling must be used.
   - cd-gpios: Specify GPIOs for card detection, see gpio binding
   - non-removable: non-removable slot (like eMMC); assume always present.
 
 Optional properties:
+- bus-width: Number of data lines, can be <1>, <4>, or <8>.  The default
+  will be <1> if the property is absent.
 - wp-gpios: Specify GPIOs for write protection, see gpio binding
-- cd-inverted: when present, polarity on the cd gpio line is inverted
-- wp-inverted: when present, polarity on the wp gpio line is inverted
+- cd-inverted: when present, polarity on the CD line is inverted. See the note
+  below for the case, when a GPIO is used for the CD line
+- wp-inverted: when present, polarity on the WP line is inverted. See the note
+  below for the case, when a GPIO is used for the WP line
 - max-frequency: maximum operating clock frequency
 - no-1-8-v: when present, denotes that 1.8v card voltage is not supported on
   this system, even if the controller claims it is.
+- cap-sd-highspeed: SD high-speed timing is supported
+- cap-mmc-highspeed: MMC high-speed timing is supported
+- cap-power-off-card: powering off the card is safe
+- cap-sdio-irq: enable SDIO IRQ signalling on this interface
+
+*NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line
+polarity properties, we have to fix the meaning of the "normal" and "inverted"
+line levels. We choose to follow the SDHCI standard, which specifies both those
+lines as "active low." Therefore, using the "cd-inverted" property means, that
+the CD line is active high, i.e. it is high, when a card is inserted. Similar
+logic applies to the "wp-inverted" property.
+
+CD and WP lines can be implemented on the hardware in one of two ways: as GPIOs,
+specified in cd-gpios and wp-gpios properties, or as dedicated pins. Polarity of
+dedicated pins can be specified, using *-inverted properties. GPIO polarity can
+also be specified using the OF_GPIO_ACTIVE_LOW flag. This creates an ambiguity
+in the latter case. We choose to use the XOR logic for GPIO CD and WP lines.
+This means, the two properties are "superimposed," for example leaving the
+OF_GPIO_ACTIVE_LOW flag clear and specifying the respective *-inverted
+property results in a double-inversion and actually means the "normal" line
+polarity is in effect.
 
 Optional SDIO properties:
 - keep-power-in-suspend: Preserves card power during a suspend/resume cycle

Documentation/devicetree/bindings/mmc/orion-sdio.txt

+* Marvell orion-sdio controller
+
+This file documents differences between the core properties in mmc.txt
+and the properties used by the orion-sdio driver.
+
+- compatible: Should be "marvell,orion-sdio"
+- clocks: reference to the clock of the SDIO interface
+
+Example:
+
+	mvsdio@d00d4000 {
+		compatible = "marvell,orion-sdio";
+		reg = <0xd00d4000 0x200>;
+		interrupts = <54>;
+		clocks = <&gateclk 17>;
+		status = "disabled";
+	};

Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt

@@ -26,8 +26,16 @@ Required Properties:
 	* bus-width: as documented in mmc core bindings.
 
 	* wp-gpios: specifies the write protect gpio line. The format of the
-	  gpio specifier depends on the gpio controller. If the write-protect
-	  line is not available, this property is optional.
+	  gpio specifier depends on the gpio controller. If a GPIO is not used
+	  for write-protect, this property is optional.
+
+	* disable-wp: If the wp-gpios property isn't present then (by default)
+	  we'd assume that the write protect is hooked up directly to the
+	  controller's special purpose write protect line (accessible via
+	  the WRTPRT register).  However, it's possible that we simply don't
+	  want write protect.  In that case specify 'disable-wp'.
+	  NOTE: This property is not required for slots known to always
+	  connect to eMMC or SDIO cards.
 
 Optional properties:
 

Documentation/devicetree/bindings/mmc/tmio_mmc.txt

+* Toshiba Mobile IO SD/MMC controller
+
+The tmio-mmc driver doesn't probe its devices actively, instead its binding to
+devices is managed by either MFD drivers or by the sh_mobile_sdhi platform
+driver. Those drivers supply the tmio-mmc driver with platform data, that either
+describe hardware capabilities, known to them, or are obtained by them from
+their own platform data or from their DT information. In the latter case all
+compulsory and any optional properties, common to all SD/MMC drivers, as
+described in mmc.txt, can be used. Additionally the following tmio_mmc-specific
+optional bindings can be used.
+
+Optional properties:
+- toshiba,mmc-wrprotect-disable: write-protect detection is unavailable
+
+When used with Renesas SDHI hardware, the following compatibility strings
+configure various model-specific properties:
+
+"renesas,sh7372-sdhi":	(default) compatible with SH7372
+"renesas,r8a7740-sdhi":	compatible with R8A7740: certain MMC/SD commands have to
+			wait for the interface to become idle.

MAINTAINERS

@@ -5692,7 +5692,7 @@ S:	Maintained
 F:	drivers/mmc/host/omap.c
 
 OMAP HS MMC SUPPORT
-M:	Venkatraman S <svenkatr@ti.com>
+M:	Balaji T K <balajitk@ti.com>
 L:	linux-mmc@vger.kernel.org
 L:	linux-omap@vger.kernel.org
 S:	Maintained
@@ -6804,6 +6804,14 @@ F:	include/linux/dw_dmac.h
 F:	drivers/dma/dw_dmac_regs.h
 F:	drivers/dma/dw_dmac.c
 
+SYNOPSYS DESIGNWARE MMC/SD/SDIO DRIVER
+M:	Seungwon Jeon <tgih.jun@samsung.com>
+M:	Jaehoon Chung <jh80.chung@samsung.com>
+L:	linux-mmc@vger.kernel.org
+S:	Maintained
+F:	include/linux/mmc/dw_mmc.h
+F:	drivers/mmc/host/dw_mmc*
+
 TIMEKEEPING, NTP
 M:	John Stultz <john.stultz@linaro.org>
 M:	Thomas Gleixner <tglx@linutronix.de>

arch/arm/boot/dts/exynos5250-smdk5250.dts

@@ -151,6 +151,7 @@ slot@0 {
 			reg = <0>;
 			bus-width = <4>;
 			samsung,cd-pinmux-gpio = <&gpc3 2 2 3 3>;
+			disable-wp;
 			gpios = <&gpc3 0 2 0 3>, <&gpc3 1 2 0 3>,
 				<&gpc3 3 2 3 3>, <&gpc3 4 2 3 3>,
 				<&gpc3 5 2 3 3>, <&gpc3 6 2 3 3>,

drivers/mmc/card/queue.c

@@ -22,7 +22,8 @@
 
 #define MMC_QUEUE_BOUNCESZ	65536
 
-#define MMC_QUEUE_SUSPENDED	(1 << 0)
+
+#define MMC_REQ_SPECIAL_MASK	(REQ_DISCARD | REQ_FLUSH)
 
 /*
  * Prepare a MMC request. This just filters out odd stuff.
@@ -58,6 +59,7 @@ static int mmc_queue_thread(void *d)
 	do {
 		struct request *req = NULL;
 		struct mmc_queue_req *tmp;
+		unsigned int cmd_flags = 0;
 
 		spin_lock_irq(q->queue_lock);
 		set_current_state(TASK_INTERRUPTIBLE);
@@ -67,12 +69,23 @@ static int mmc_queue_thread(void *d)
 
 		if (req || mq->mqrq_prev->req) {
 			set_current_state(TASK_RUNNING);
+			cmd_flags = req ? req->cmd_flags : 0;
 			mq->issue_fn(mq, req);
+			if (mq->flags & MMC_QUEUE_NEW_REQUEST) {
+				mq->flags &= ~MMC_QUEUE_NEW_REQUEST;
+				continue; /* fetch again */
+			}
 
 			/*
 			 * Current request becomes previous request
 			 * and vice versa.
+			 * In case of special requests, current request
+			 * has been finished. Do not assign it to previous
+			 * request.
 			 */
+			if (cmd_flags & MMC_REQ_SPECIAL_MASK)
+				mq->mqrq_cur->req = NULL;
+
 			mq->mqrq_prev->brq.mrq.data = NULL;
 			mq->mqrq_prev->req = NULL;
 			tmp = mq->mqrq_prev;
@@ -103,6 +116,8 @@ static void mmc_request_fn(struct request_queue *q)
 {
 	struct mmc_queue *mq = q->queuedata;
 	struct request *req;
+	unsigned long flags;
+	struct mmc_context_info *cntx;
 
 	if (!mq) {
 		while ((req = blk_fetch_request(q)) != NULL) {
@@ -112,7 +127,20 @@ static void mmc_request_fn(struct request_queue *q)
 		return;
 	}
 
-	if (!mq->mqrq_cur->req && !mq->mqrq_prev->req)
+	cntx = &mq->card->host->context_info;
+	if (!mq->mqrq_cur->req && mq->mqrq_prev->req) {
+		/*
+		 * New MMC request arrived when MMC thread may be
+		 * blocked on the previous request to be complete
+		 * with no current request fetched
+		 */
+		spin_lock_irqsave(&cntx->lock, flags);
+		if (cntx->is_waiting_last_req) {
+			cntx->is_new_req = true;
+			wake_up_interruptible(&cntx->wait);
+		}
+		spin_unlock_irqrestore(&cntx->lock, flags);
+	} else if (!mq->mqrq_cur->req && !mq->mqrq_prev->req)
 		wake_up_process(mq->thread);
 }
 
@@ -334,6 +362,49 @@ void mmc_cleanup_queue(struct mmc_queue *mq)
 }
 EXPORT_SYMBOL(mmc_cleanup_queue);
 
+int mmc_packed_init(struct mmc_queue *mq, struct mmc_card *card)
+{
+	struct mmc_queue_req *mqrq_cur = &mq->mqrq[0];
+	struct mmc_queue_req *mqrq_prev = &mq->mqrq[1];
+	int ret = 0;
+
+
+	mqrq_cur->packed = kzalloc(sizeof(struct mmc_packed), GFP_KERNEL);
+	if (!mqrq_cur->packed) {
+		pr_warn("%s: unable to allocate packed cmd for mqrq_cur\n",
+			mmc_card_name(card));
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	mqrq_prev->packed = kzalloc(sizeof(struct mmc_packed), GFP_KERNEL);
+	if (!mqrq_prev->packed) {
+		pr_warn("%s: unable to allocate packed cmd for mqrq_prev\n",
+			mmc_card_name(card));
+		kfree(mqrq_cur->packed);
+		mqrq_cur->packed = NULL;
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	INIT_LIST_HEAD(&mqrq_cur->packed->list);
+	INIT_LIST_HEAD(&mqrq_prev->packed->list);
+
+out:
+	return ret;
+}
+
+void mmc_packed_clean(struct mmc_queue *mq)
+{
+	struct mmc_queue_req *mqrq_cur = &mq->mqrq[0];
+	struct mmc_queue_req *mqrq_prev = &mq->mqrq[1];
+
+	kfree(mqrq_cur->packed);
+	mqrq_cur->packed = NULL;
+	kfree(mqrq_prev->packed);
+	mqrq_prev->packed = NULL;
+}
+
 /**
  * mmc_queue_suspend - suspend a MMC request queue
  * @mq: MMC queue to suspend
@@ -378,6 +449,41 @@ void mmc_queue_resume(struct mmc_queue *mq)
 	}
 }
 
+static unsigned int mmc_queue_packed_map_sg(struct mmc_queue *mq,
+					    struct mmc_packed *packed,
+					    struct scatterlist *sg,
+					    enum mmc_packed_type cmd_type)
+{
+	struct scatterlist *__sg = sg;
+	unsigned int sg_len = 0;
+	struct request *req;
+
+	if (mmc_packed_wr(cmd_type)) {
+		unsigned int hdr_sz = mmc_large_sector(mq->card) ? 4096 : 512;
+		unsigned int max_seg_sz = queue_max_segment_size(mq->queue);
+		unsigned int len, remain, offset = 0;
+		u8 *buf = (u8 *)packed->cmd_hdr;
+
+		remain = hdr_sz;
+		do {
+			len = min(remain, max_seg_sz);
+			sg_set_buf(__sg, buf + offset, len);
+			offset += len;
+			remain -= len;
+			(__sg++)->page_link &= ~0x02;
+			sg_len++;
+		} while (remain);
+	}
+
+	list_for_each_entry(req, &packed->list, queuelist) {
+		sg_len += blk_rq_map_sg(mq->queue, req, __sg);
+		__sg = sg + (sg_len - 1);
+		(__sg++)->page_link &= ~0x02;
+	}
+	sg_mark_end(sg + (sg_len - 1));
+	return sg_len;
+}
+
 /*
  * Prepare the sg list(s) to be handed of to the host driver
  */
@@ -386,13 +492,25 @@ unsigned int mmc_queue_map_sg(struct mmc_queue *mq, struct mmc_queue_req *mqrq)
 	unsigned int sg_len;
 	size_t buflen;
 	struct scatterlist *sg;
+	enum mmc_packed_type cmd_type;
 	int i;
 
-	if (!mqrq->bounce_buf)
+	cmd_type = mqrq->cmd_type;
+
+	if (!mqrq->bounce_buf) {
+		if (mmc_packed_cmd(cmd_type))
+			return mmc_queue_packed_map_sg(mq, mqrq->packed,
+						       mqrq->sg, cmd_type);
+		else
 			return blk_rq_map_sg(mq->queue, mqrq->req, mqrq->sg);
+	}
 
 	BUG_ON(!mqrq->bounce_sg);
 
+	if (mmc_packed_cmd(cmd_type))
+		sg_len = mmc_queue_packed_map_sg(mq, mqrq->packed,
+						 mqrq->bounce_sg, cmd_type);
+	else
 		sg_len = blk_rq_map_sg(mq->queue, mqrq->req, mqrq->bounce_sg);
 
 	mqrq->bounce_sg_len = sg_len;

drivers/mmc/card/queue.h

@@ -12,6 +12,23 @@ struct mmc_blk_request {
 	struct mmc_data		data;
 };
 
+enum mmc_packed_type {
+	MMC_PACKED_NONE = 0,
+	MMC_PACKED_WRITE,
+};
+
+#define mmc_packed_cmd(type)	((type) != MMC_PACKED_NONE)
+#define mmc_packed_wr(type)	((type) == MMC_PACKED_WRITE)
+
+struct mmc_packed {
+	struct list_head	list;
+	u32			cmd_hdr[1024];
+	unsigned int		blocks;
+	u8			nr_entries;
+	u8			retries;
+	s16			idx_failure;
+};
+
 struct mmc_queue_req {
 	struct request		*req;
 	struct mmc_blk_request	brq;
@@ -20,6 +37,8 @@ struct mmc_queue_req {
 	struct scatterlist	*bounce_sg;
 	unsigned int		bounce_sg_len;
 	struct mmc_async_req	mmc_active;
+	enum mmc_packed_type	cmd_type;
+	struct mmc_packed	*packed;
 };
 
 struct mmc_queue {
@@ -27,6 +46,9 @@ struct mmc_queue {
 	struct task_struct	*thread;
 	struct semaphore	thread_sem;
 	unsigned int		flags;
+#define MMC_QUEUE_SUSPENDED	(1 << 0)
+#define MMC_QUEUE_NEW_REQUEST	(1 << 1)
+
 	int			(*issue_fn)(struct mmc_queue *, struct request *);
 	void			*data;
 	struct request_queue	*queue;
@@ -46,4 +68,7 @@ extern unsigned int mmc_queue_map_sg(struct mmc_queue *,
 extern void mmc_queue_bounce_pre(struct mmc_queue_req *);
 extern void mmc_queue_bounce_post(struct mmc_queue_req *);
 
+extern int mmc_packed_init(struct mmc_queue *, struct mmc_card *);
+extern void mmc_packed_clean(struct mmc_queue *);
+
 #endif

drivers/mmc/core/bus.c

@@ -321,6 +321,7 @@ int mmc_add_card(struct mmc_card *card)
 #ifdef CONFIG_DEBUG_FS
 	mmc_add_card_debugfs(card);
 #endif
+	mmc_init_context_info(card->host);
 
 	ret = device_add(&card->dev);
 	if (ret)

drivers/mmc/core/core.c

@@ -319,11 +319,45 @@ void mmc_start_bkops(struct mmc_card *card, bool from_exception)
 }
 EXPORT_SYMBOL(mmc_start_bkops);
 
+/*
+ * mmc_wait_data_done() - done callback for data request
+ * @mrq: done data request
+ *
+ * Wakes up mmc context, passed as a callback to host controller driver
+ */
+static void mmc_wait_data_done(struct mmc_request *mrq)
+{
+	mrq->host->context_info.is_done_rcv = true;
+	wake_up_interruptible(&mrq->host->context_info.wait);
+}
+
 static void mmc_wait_done(struct mmc_request *mrq)
 {
 	complete(&mrq->completion);
 }
 
+/*
+ *__mmc_start_data_req() - starts data request
+ * @host: MMC host to start the request
+ * @mrq: data request to start
+ *
+ * Sets the done callback to be called when request is completed by the card.
+ * Starts data mmc request execution
+ */
+static int __mmc_start_data_req(struct mmc_host *host, struct mmc_request *mrq)
+{
+	mrq->done = mmc_wait_data_done;
+	mrq->host = host;
+	if (mmc_card_removed(host->card)) {
+		mrq->cmd->error = -ENOMEDIUM;
+		mmc_wait_data_done(mrq);
+		return -ENOMEDIUM;
+	}
+	mmc_start_request(host, mrq);
+
+	return 0;
+}
+
 static int __mmc_start_req(struct mmc_host *host, struct mmc_request *mrq)
 {
 	init_completion(&mrq->completion);
@@ -337,6 +371,62 @@ static int __mmc_start_req(struct mmc_host *host, struct mmc_request *mrq)
 	return 0;
 }
 
+/*
+ * mmc_wait_for_data_req_done() - wait for request completed
+ * @host: MMC host to prepare the command.
+ * @mrq: MMC request to wait for
+ *
+ * Blocks MMC context till host controller will ack end of data request
+ * execution or new request notification arrives from the block layer.
+ * Handles command retries.
+ *
+ * Returns enum mmc_blk_status after checking errors.
+ */
+static int mmc_wait_for_data_req_done(struct mmc_host *host,
+				      struct mmc_request *mrq,
+				      struct mmc_async_req *next_req)
+{
+	struct mmc_command *cmd;
+	struct mmc_context_info *context_info = &host->context_info;
+	int err;
+	unsigned long flags;
+
+	while (1) {
+		wait_event_interruptible(context_info->wait,
+				(context_info->is_done_rcv ||
+				 context_info->is_new_req));
+		spin_lock_irqsave(&context_info->lock, flags);
+		context_info->is_waiting_last_req = false;
+		spin_unlock_irqrestore(&context_info->lock, flags);
+		if (context_info->is_done_rcv) {
+			context_info->is_done_rcv = false;
+			context_info->is_new_req = false;
+			cmd = mrq->cmd;
+			if (!cmd->error || !cmd->retries ||
+			    mmc_card_removed(host->card)) {
+				err = host->areq->err_check(host->card,
+							    host->areq);
+				break; /* return err */
+			} else {
+				pr_info("%s: req failed (CMD%u): %d, retrying...\n",
+					mmc_hostname(host),
+					cmd->opcode, cmd->error);
+				cmd->retries--;
+				cmd->error = 0;
+				host->ops->request(host, mrq);
+				continue; /* wait for done/new event again */
+			}
+		} else if (context_info->is_new_req) {
+			context_info->is_new_req = false;
+			if (!next_req) {
+				err = MMC_BLK_NEW_REQUEST;
+				break; /* return err */
+			}
+		}
+	}
+	return err;
+}
+
 static void mmc_wait_for_req_done(struct mmc_host *host,
 				  struct mmc_request *mrq)
 {
@@ -426,8 +516,16 @@ struct mmc_async_req *mmc_start_req(struct mmc_host *host,
 		mmc_pre_req(host, areq->mrq, !host->areq);
 
 	if (host->areq) {
-		mmc_wait_for_req_done(host, host->areq->mrq);
-		err = host->areq->err_check(host->card, host->areq);
+		err = mmc_wait_for_data_req_done(host, host->areq->mrq,	areq);
+		if (err == MMC_BLK_NEW_REQUEST) {
+			if (error)
+				*error = err;
+			/*
+			 * The previous request was not completed,
+			 * nothing to return
+			 */
+			return NULL;
+		}
 		/*
 		 * Check BKOPS urgency for each R1 response
 		 */
@@ -439,7 +537,7 @@ struct mmc_async_req *mmc_start_req(struct mmc_host *host,
 	}
 
 	if (!err && areq)
-		start_err = __mmc_start_req(host, areq->mrq);
+		start_err = __mmc_start_data_req(host, areq->mrq);
 
 	if (host->areq)
 		mmc_post_req(host, host->areq->mrq, 0);
@@ -1137,7 +1235,7 @@ int mmc_regulator_set_ocr(struct mmc_host *mmc,
 		 */
 		voltage = regulator_get_voltage(supply);
 
-		if (regulator_count_voltages(supply) == 1)
+		if (!regulator_can_change_voltage(supply))
 			min_uV = max_uV = voltage;
 
 		if (voltage < 0)
@@ -1219,10 +1317,30 @@ u32 mmc_select_voltage(struct mmc_host *host, u32 ocr)
 	return ocr;
 }
 
-int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage, bool cmd11)
+int __mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage)
+{
+	int err = 0;
+	int old_signal_voltage = host->ios.signal_voltage;
+
+	host->ios.signal_voltage = signal_voltage;
+	if (host->ops->start_signal_voltage_switch) {
+		mmc_host_clk_hold(host);
+		err = host->ops->start_signal_voltage_switch(host, &host->ios);
+		mmc_host_clk_release(host);
+	}
+
+	if (err)
+		host->ios.signal_voltage = old_signal_voltage;
+
+	return err;
+
+}
+
+int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage)
 {
 	struct mmc_command cmd = {0};
 	int err = 0;
+	u32 clock;
 
 	BUG_ON(!host);
 
@@ -1230,7 +1348,19 @@ int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage, bool cmd11
 	 * Send CMD11 only if the request is to switch the card to
 	 * 1.8V signalling.
 	 */
-	if ((signal_voltage != MMC_SIGNAL_VOLTAGE_330) && cmd11) {
+	if (signal_voltage == MMC_SIGNAL_VOLTAGE_330)
+		return __mmc_set_signal_voltage(host, signal_voltage);
+
+	/*
+	 * If we cannot switch voltages, return failure so the caller
+	 * can continue without UHS mode
+	 */
+	if (!host->ops->start_signal_voltage_switch)
+		return -EPERM;
+	if (!host->ops->card_busy)
+		pr_warning("%s: cannot verify signal voltage switch\n",
+				mmc_hostname(host));
+
 	cmd.opcode = SD_SWITCH_VOLTAGE;
 	cmd.arg = 0;
 	cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;
@@ -1241,16 +1371,58 @@ int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage, bool cmd11
 
 	if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR))
 		return -EIO;
+
+	mmc_host_clk_hold(host);
+	/*
+	 * The card should drive cmd and dat[0:3] low immediately
+	 * after the response of cmd11, but wait 1 ms to be sure
+	 */
+	mmc_delay(1);
+	if (host->ops->card_busy && !host->ops->card_busy(host)) {
+		err = -EAGAIN;
+		goto power_cycle;
 	}
+	/*
+	 * During a signal voltage level switch, the clock must be gated
+	 * for 5 ms according to the SD spec
+	 */
+	clock = host->ios.clock;
+	host->ios.clock = 0;
+	mmc_set_ios(host);
 
-	host->ios.signal_voltage = signal_voltage;
+	if (__mmc_set_signal_voltage(host, signal_voltage)) {
+		/*
+		 * Voltages may not have been switched, but we've already
+		 * sent CMD11, so a power cycle is required anyway
+		 */
+		err = -EAGAIN;
+		goto power_cycle;
+	}
 
-	if (host->ops->start_signal_voltage_switch) {
-		mmc_host_clk_hold(host);
-		err = host->ops->start_signal_voltage_switch(host, &host->ios);
-		mmc_host_clk_release(host);
+	/* Keep clock gated for at least 5 ms */
+	mmc_delay(5);
+	host->ios.clock = clock;
+	mmc_set_ios(host);
+
+	/* Wait for at least 1 ms according to spec */
+	mmc_delay(1);
+
+	/*
+	 * Failure to switch is indicated by the card holding
+	 * dat[0:3] low
+	 */
+	if (host->ops->card_busy && host->ops->card_busy(host))
+		err = -EAGAIN;
+
+power_cycle:
+	if (err) {
+		pr_debug("%s: Signal voltage switch failed, "
+			"power cycling card\n", mmc_hostname(host));
+		mmc_power_cycle(host);
 	}
 
+	mmc_host_clk_release(host);
+
 	return err;
 }
 
@@ -1314,7 +1486,7 @@ static void mmc_power_up(struct mmc_host *host)
 	mmc_set_ios(host);
 
 	/* Set signal voltage to 3.3V */
-	mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, false);
+	__mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330);
 
 	/*
 	 * This delay should be sufficient to allow the power supply
@@ -1372,6 +1544,14 @@ void mmc_power_off(struct mmc_host *host)
 	mmc_host_clk_release(host);
 }
 
+void mmc_power_cycle(struct mmc_host *host)
+{
+	mmc_power_off(host);
+	/* Wait at least 1 ms according to SD spec */
+	mmc_delay(1);
+	mmc_power_up(host);
+}
+
 /*
  * Cleanup when the last reference to the bus operator is dropped.
  */
@@ -2388,6 +2568,7 @@ EXPORT_SYMBOL(mmc_flush_cache);
  * Turn the cache ON/OFF.
  * Turning the cache OFF shall trigger flushing of the data
  * to the non-volatile storage.
+ * This function should be called with host claimed
  */
 int mmc_cache_ctrl(struct mmc_host *host, u8 enable)
 {
@@ -2399,7 +2580,6 @@ int mmc_cache_ctrl(struct mmc_host *host, u8 enable)
 			mmc_card_is_removable(host))
 		return err;
 
-	mmc_claim_host(host);
 	if (card && mmc_card_mmc(card) &&
 			(card->ext_csd.cache_size > 0)) {
 		enable = !!enable;
@@ -2417,7 +2597,6 @@ int mmc_cache_ctrl(struct mmc_host *host, u8 enable)
 				card->ext_csd.cache_ctrl = enable;
 		}
 	}
-	mmc_release_host(host);
 
 	return err;
 }
@@ -2436,10 +2615,6 @@ int mmc_suspend_host(struct mmc_host *host)
 	cancel_delayed_work(&host->detect);
 	mmc_flush_scheduled_work();
 
-	err = mmc_cache_ctrl(host, 0);
-	if (err)
-		goto out;
-
 	mmc_bus_get(host);
 	if (host->bus_ops && !host->bus_dead) {
 		if (host->bus_ops->suspend) {
@@ -2581,6 +2756,23 @@ int mmc_pm_notify(struct notifier_block *notify_block,
 }
 #endif
 
+/**
+ * mmc_init_context_info() - init synchronization context
+ * @host: mmc host
+ *
+ * Init struct context_info needed to implement asynchronous
+ * request mechanism, used by mmc core, host driver and mmc requests
+ * supplier.
+ */
+void mmc_init_context_info(struct mmc_host *host)
+{
+	spin_lock_init(&host->context_info.lock);
+	host->context_info.is_new_req = false;
+	host->context_info.is_done_rcv = false;
+	host->context_info.is_waiting_last_req = false;
+	init_waitqueue_head(&host->context_info.wait);
+}
+
 static int __init mmc_init(void)
 {
 	int ret;

drivers/mmc/core/core.h

@@ -40,11 +40,12 @@ void mmc_set_ungated(struct mmc_host *host);
 void mmc_set_bus_mode(struct mmc_host *host, unsigned int mode);
 void mmc_set_bus_width(struct mmc_host *host, unsigned int width);
 u32 mmc_select_voltage(struct mmc_host *host, u32 ocr);
-int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage,
-			   bool cmd11);
+int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage);
+int __mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage);
 void mmc_set_timing(struct mmc_host *host, unsigned int timing);
 void mmc_set_driver_type(struct mmc_host *host, unsigned int drv_type);
 void mmc_power_off(struct mmc_host *host);
+void mmc_power_cycle(struct mmc_host *host);
 
 static inline void mmc_delay(unsigned int ms)
 {
@@ -76,5 +77,6 @@ void mmc_remove_host_debugfs(struct mmc_host *host);
 void mmc_add_card_debugfs(struct mmc_card *card);
 void mmc_remove_card_debugfs(struct mmc_card *card);
 
+void mmc_init_context_info(struct mmc_host *host);
 #endif
 

drivers/mmc/core/host.c

@@ -15,6 +15,8 @@
 #include <linux/device.h>
 #include <linux/err.h>
 #include <linux/idr.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
 #include <linux/pagemap.h>
 #include <linux/export.h>
 #include <linux/leds.h>
@@ -23,6 +25,7 @@
 
 #include <linux/mmc/host.h>
 #include <linux/mmc/card.h>
+#include <linux/mmc/slot-gpio.h>
 
 #include "core.h"
 #include "host.h"
@@ -294,6 +297,126 @@ static inline void mmc_host_clk_sysfs_init(struct mmc_host *host)
 
 #endif
 
+/**
+ *	mmc_of_parse() - parse host's device-tree node
+ *	@host: host whose node should be parsed.
+ *
+ * To keep the rest of the MMC subsystem unaware of whether DT has been
+ * used to to instantiate and configure this host instance or not, we
+ * parse the properties and set respective generic mmc-host flags and
+ * parameters.
+ */
+void mmc_of_parse(struct mmc_host *host)
+{
+	struct device_node *np;
+	u32 bus_width;
+	bool explicit_inv_wp, gpio_inv_wp = false;
+	enum of_gpio_flags flags;
+	int len, ret, gpio;
+
+	if (!host->parent || !host->parent->of_node)
+		return;
+
+	np = host->parent->of_node;
+
+	/* "bus-width" is translated to MMC_CAP_*_BIT_DATA flags */
+	if (of_property_read_u32(np, "bus-width", &bus_width) < 0) {
+		dev_dbg(host->parent,
+			"\"bus-width\" property is missing, assuming 1 bit.\n");
+		bus_width = 1;
+	}
+
+	switch (bus_width) {
+	case 8:
+		host->caps |= MMC_CAP_8_BIT_DATA;
+		/* Hosts capable of 8-bit transfers can also do 4 bits */
+	case 4:
+		host->caps |= MMC_CAP_4_BIT_DATA;
+		break;
+	case 1:
+		break;
+	default:
+		dev_err(host->parent,
+			"Invalid \"bus-width\" value %ud!\n", bus_width);
+	}
+
+	/* f_max is obtained from the optional "max-frequency" property */
+	of_property_read_u32(np, "max-frequency", &host->f_max);
+
+	/*
+	 * Configure CD and WP pins. They are both by default active low to
+	 * match the SDHCI spec. If GPIOs are provided for CD and / or WP, the
+	 * mmc-gpio helpers are used to attach, configure and use them. If
+	 * polarity inversion is specified in DT, one of MMC_CAP2_CD_ACTIVE_HIGH
+	 * and MMC_CAP2_RO_ACTIVE_HIGH capability-2 flags is set. If the
+	 * "broken-cd" property is provided, the MMC_CAP_NEEDS_POLL capability
+	 * is set. If the "non-removable" property is found, the
+	 * MMC_CAP_NONREMOVABLE capability is set and no card-detection
+	 * configuration is performed.
+	 */
+
+	/* Parse Card Detection */
+	if (of_find_property(np, "non-removable", &len)) {
+		host->caps |= MMC_CAP_NONREMOVABLE;
+	} else {
+		bool explicit_inv_cd, gpio_inv_cd = false;
+
+		explicit_inv_cd = of_property_read_bool(np, "cd-inverted");
+
+		if (of_find_property(np, "broken-cd", &len))
+			host->caps |= MMC_CAP_NEEDS_POLL;
+
+		gpio = of_get_named_gpio_flags(np, "cd-gpios", 0, &flags);
+		if (gpio_is_valid(gpio)) {
+			if (!(flags & OF_GPIO_ACTIVE_LOW))
+				gpio_inv_cd = true;
+
+			ret = mmc_gpio_request_cd(host, gpio);
+			if (ret < 0)
+				dev_err(host->parent,
+					"Failed to request CD GPIO #%d: %d!\n",
+					gpio, ret);
+			else
+				dev_info(host->parent, "Got CD GPIO #%d.\n",
+					 gpio);
+		}
+
+		if (explicit_inv_cd ^ gpio_inv_cd)
+			host->caps2 |= MMC_CAP2_CD_ACTIVE_HIGH;
+	}
+
+	/* Parse Write Protection */
+	explicit_inv_wp = of_property_read_bool(np, "wp-inverted");
+
+	gpio = of_get_named_gpio_flags(np, "wp-gpios", 0, &flags);
+	if (gpio_is_valid(gpio)) {
+		if (!(flags & OF_GPIO_ACTIVE_LOW))
+			gpio_inv_wp = true;
+
+		ret = mmc_gpio_request_ro(host, gpio);
+		if (ret < 0)
+			dev_err(host->parent,
+				"Failed to request WP GPIO: %d!\n", ret);
+	}
+	if (explicit_inv_wp ^ gpio_inv_wp)
+		host->caps2 |= MMC_CAP2_RO_ACTIVE_HIGH;
+
+	if (of_find_property(np, "cap-sd-highspeed", &len))
+		host->caps |= MMC_CAP_SD_HIGHSPEED;
+	if (of_find_property(np, "cap-mmc-highspeed", &len))
+		host->caps |= MMC_CAP_MMC_HIGHSPEED;
+	if (of_find_property(np, "cap-power-off-card", &len))
+		host->caps |= MMC_CAP_POWER_OFF_CARD;
+	if (of_find_property(np, "cap-sdio-irq", &len))
+		host->caps |= MMC_CAP_SDIO_IRQ;
+	if (of_find_property(np, "keep-power-in-suspend", &len))
+		host->pm_caps |= MMC_PM_KEEP_POWER;
+	if (of_find_property(np, "enable-sdio-wakeup", &len))
+		host->pm_caps |= MMC_PM_WAKE_SDIO_IRQ;
+}
+
+EXPORT_SYMBOL(mmc_of_parse);
+
 /**
  *	mmc_alloc_host - initialise the per-host structure.
  *	@extra: sizeof private data structure

drivers/mmc/core/mmc.c

@@ -496,7 +496,7 @@ static int mmc_read_ext_csd(struct mmc_card *card, u8 *ext_csd)
 		 * RPMB regions are defined in multiples of 128K.
 		 */
 		card->ext_csd.raw_rpmb_size_mult = ext_csd[EXT_CSD_RPMB_MULT];
-		if (ext_csd[EXT_CSD_RPMB_MULT]) {
+		if (ext_csd[EXT_CSD_RPMB_MULT] && mmc_host_cmd23(card->host)) {
 			mmc_part_add(card, ext_csd[EXT_CSD_RPMB_MULT] << 17,
 				EXT_CSD_PART_CONFIG_ACC_RPMB,
 				"rpmb", 0, false,
@@ -538,6 +538,11 @@ static int mmc_read_ext_csd(struct mmc_card *card, u8 *ext_csd)
 		} else {
 			card->ext_csd.data_tag_unit_size = 0;
 		}
+
+		card->ext_csd.max_packed_writes =
+			ext_csd[EXT_CSD_MAX_PACKED_WRITES];
+		card->ext_csd.max_packed_reads =
+			ext_csd[EXT_CSD_MAX_PACKED_READS];
 	} else {
 		card->ext_csd.data_sector_size = 512;
 	}
@@ -769,11 +774,11 @@ static int mmc_select_hs200(struct mmc_card *card)
 
 	if (card->ext_csd.card_type & EXT_CSD_CARD_TYPE_SDR_1_2V &&
 			host->caps2 & MMC_CAP2_HS200_1_2V_SDR)
-		err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120, 0);
+		err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120);
 
 	if (err && card->ext_csd.card_type & EXT_CSD_CARD_TYPE_SDR_1_8V &&
 			host->caps2 & MMC_CAP2_HS200_1_8V_SDR)
-		err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180, 0);
+		err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180);
 
 	/* If fails try again during next card power cycle */
 	if (err)
@@ -1221,8 +1226,8 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
 			 * WARNING: eMMC rules are NOT the same as SD DDR
 			 */
 			if (ddr == MMC_1_2V_DDR_MODE) {
-				err = mmc_set_signal_voltage(host,
-					MMC_SIGNAL_VOLTAGE_120, 0);
+				err = __mmc_set_signal_voltage(host,
+					MMC_SIGNAL_VOLTAGE_120);
 				if (err)
 					goto err;
 			}
@@ -1275,6 +1280,29 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
 		}
 	}
 
+	/*
+	 * The mandatory minimum values are defined for packed command.
+	 * read: 5, write: 3
+	 */
+	if (card->ext_csd.max_packed_writes >= 3 &&
+	    card->ext_csd.max_packed_reads >= 5 &&
+	    host->caps2 & MMC_CAP2_PACKED_CMD) {
+		err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
+				EXT_CSD_EXP_EVENTS_CTRL,
+				EXT_CSD_PACKED_EVENT_EN,
+				card->ext_csd.generic_cmd6_time);
+		if (err && err != -EBADMSG)
+			goto free_card;
+		if (err) {
+			pr_warn("%s: Enabling packed event failed\n",
+				mmc_hostname(card->host));
+			card->ext_csd.packed_event_en = 0;
+			err = 0;
+		} else {
+			card->ext_csd.packed_event_en = 1;
+		}
+	}
+
 	if (!oldcard)
 		host->card = card;
 
@@ -1379,6 +1407,11 @@ static int mmc_suspend(struct mmc_host *host)
 	BUG_ON(!host->card);
 
 	mmc_claim_host(host);
+
+	err = mmc_cache_ctrl(host, 0);
+	if (err)
+		goto out;
+
 	if (mmc_can_poweroff_notify(host->card))
 		err = mmc_poweroff_notify(host->card, EXT_CSD_POWER_OFF_SHORT);
 	else if (mmc_card_can_sleep(host))
@@ -1386,8 +1419,9 @@ static int mmc_suspend(struct mmc_host *host)
 	else if (!mmc_host_is_spi(host))
 		err = mmc_deselect_cards(host);
 	host->card->state &= ~(MMC_STATE_HIGHSPEED | MMC_STATE_HIGHSPEED_200);
-	mmc_release_host(host);
 
+out:
+	mmc_release_host(host);
 	return err;
 }
 

drivers/mmc/core/mmc_ops.c

@@ -363,6 +363,7 @@ int mmc_send_ext_csd(struct mmc_card *card, u8 *ext_csd)
 	return mmc_send_cxd_data(card, card->host, MMC_SEND_EXT_CSD,
 			ext_csd, 512);
 }
+EXPORT_SYMBOL_GPL(mmc_send_ext_csd);
 
 int mmc_spi_read_ocr(struct mmc_host *host, int highcap, u32 *ocrp)
 {

drivers/mmc/core/sd.c

@@ -444,8 +444,7 @@ static void sd_update_bus_speed_mode(struct mmc_card *card)
 	 * If the host doesn't support any of the UHS-I modes, fallback on
 	 * default speed.
 	 */
-	if (!(card->host->caps & (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 |
-	    MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 | MMC_CAP_UHS_DDR50))) {
+	if (!mmc_host_uhs(card->host)) {
 		card->sd_bus_speed = 0;
 		return;
 	}
@@ -713,6 +712,14 @@ int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid, u32 *rocr)
 {
 	int err;
 	u32 max_current;
+	int retries = 10;
+
+try_again:
+	if (!retries) {
+		ocr &= ~SD_OCR_S18R;
+		pr_warning("%s: Skipping voltage switch\n",
+			mmc_hostname(host));
+	}
 
 	/*
 	 * Since we're changing the OCR value, we seem to
@@ -734,10 +741,10 @@ int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid, u32 *rocr)
 
 	/*
 	 * If the host supports one of UHS-I modes, request the card
-	 * to switch to 1.8V signaling level.
+	 * to switch to 1.8V signaling level. If the card has failed
+	 * repeatedly to switch however, skip this.
 	 */
-	if (host->caps & (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 |
-	    MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 | MMC_CAP_UHS_DDR50))
+	if (retries && mmc_host_uhs(host))
 		ocr |= SD_OCR_S18R;
 
 	/*
@@ -748,7 +755,6 @@ int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid, u32 *rocr)
 	if (max_current > 150)
 		ocr |= SD_OCR_XPC;
 
-try_again:
 	err = mmc_send_app_op_cond(host, ocr, rocr);
 	if (err)
 		return err;
@@ -759,9 +765,12 @@ int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid, u32 *rocr)
 	 */
 	if (!mmc_host_is_spi(host) && rocr &&
 	   ((*rocr & 0x41000000) == 0x41000000)) {
-		err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180, true);
-		if (err) {
-			ocr &= ~SD_OCR_S18R;
+		err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180);
+		if (err == -EAGAIN) {
+			retries--;
+			goto try_again;
+		} else if (err) {
+			retries = 0;
 			goto try_again;
 		}
 	}
@@ -960,16 +969,6 @@ static int mmc_sd_init_card(struct mmc_host *host, u32 ocr,
 
 		/* Card is an ultra-high-speed card */
 		mmc_card_set_uhs(card);
-
-		/*
-		 * Since initialization is now complete, enable preset
-		 * value registers for UHS-I cards.
-		 */
-		if (host->ops->enable_preset_value) {
-			mmc_host_clk_hold(card->host);
-			host->ops->enable_preset_value(host, true);
-			mmc_host_clk_release(card->host);
-		}
 	} else {
 		/*
 		 * Attempt to change to high-speed (if supported)
@@ -1148,13 +1147,6 @@ int mmc_attach_sd(struct mmc_host *host)
 	BUG_ON(!host);
 	WARN_ON(!host->claimed);
 
-	/* Disable preset value enable if already set since last time */
-	if (host->ops->enable_preset_value) {
-		mmc_host_clk_hold(host);
-		host->ops->enable_preset_value(host, false);
-		mmc_host_clk_release(host);
-	}
-
 	err = mmc_send_app_op_cond(host, 0, &ocr);
 	if (err)
 		return err;

drivers/mmc/core/sdio.c

@@ -157,10 +157,7 @@ static int sdio_read_cccr(struct mmc_card *card, u32 ocr)
 			if (ret)
 				goto out;
 
-			if (card->host->caps &
-				(MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 |
-				 MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 |
-				 MMC_CAP_UHS_DDR50)) {
+			if (mmc_host_uhs(card->host)) {
 				if (data & SDIO_UHS_DDR50)
 					card->sw_caps.sd3_bus_mode
 						|= SD_MODE_UHS_DDR50;
@@ -478,8 +475,7 @@ static int sdio_set_bus_speed_mode(struct mmc_card *card)
 	 * If the host doesn't support any of the UHS-I modes, fallback on
 	 * default speed.
 	 */
-	if (!(card->host->caps & (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 |
-	    MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 | MMC_CAP_UHS_DDR50)))
+	if (!mmc_host_uhs(card->host))
 		return 0;
 
 	bus_speed = SDIO_SPEED_SDR12;
@@ -489,23 +485,27 @@ static int sdio_set_bus_speed_mode(struct mmc_card *card)
 			bus_speed = SDIO_SPEED_SDR104;
 			timing = MMC_TIMING_UHS_SDR104;
 			card->sw_caps.uhs_max_dtr = UHS_SDR104_MAX_DTR;
+			card->sd_bus_speed = UHS_SDR104_BUS_SPEED;
 	} else if ((card->host->caps & MMC_CAP_UHS_DDR50) &&
 		   (card->sw_caps.sd3_bus_mode & SD_MODE_UHS_DDR50)) {
 			bus_speed = SDIO_SPEED_DDR50;
 			timing = MMC_TIMING_UHS_DDR50;
 			card->sw_caps.uhs_max_dtr = UHS_DDR50_MAX_DTR;
+			card->sd_bus_speed = UHS_DDR50_BUS_SPEED;
 	} else if ((card->host->caps & (MMC_CAP_UHS_SDR104 |
 		    MMC_CAP_UHS_SDR50)) && (card->sw_caps.sd3_bus_mode &
 		    SD_MODE_UHS_SDR50)) {
 			bus_speed = SDIO_SPEED_SDR50;
 			timing = MMC_TIMING_UHS_SDR50;
 			card->sw_caps.uhs_max_dtr = UHS_SDR50_MAX_DTR;
+			card->sd_bus_speed = UHS_SDR50_BUS_SPEED;
 	} else if ((card->host->caps & (MMC_CAP_UHS_SDR104 |
 		    MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR25)) &&
 		   (card->sw_caps.sd3_bus_mode & SD_MODE_UHS_SDR25)) {
 			bus_speed = SDIO_SPEED_SDR25;
 			timing = MMC_TIMING_UHS_SDR25;
 			card->sw_caps.uhs_max_dtr = UHS_SDR25_MAX_DTR;
+			card->sd_bus_speed = UHS_SDR25_BUS_SPEED;
 	} else if ((card->host->caps & (MMC_CAP_UHS_SDR104 |
 		    MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR25 |
 		    MMC_CAP_UHS_SDR12)) && (card->sw_caps.sd3_bus_mode &
@@ -513,6 +513,7 @@ static int sdio_set_bus_speed_mode(struct mmc_card *card)
 			bus_speed = SDIO_SPEED_SDR12;
 			timing = MMC_TIMING_UHS_SDR12;
 			card->sw_caps.uhs_max_dtr = UHS_SDR12_MAX_DTR;
+			card->sd_bus_speed = UHS_SDR12_BUS_SPEED;
 	}
 
 	err = mmc_io_rw_direct(card, 0, 0, SDIO_CCCR_SPEED, 0, &speed);
@@ -583,10 +584,19 @@ static int mmc_sdio_init_card(struct mmc_host *host, u32 ocr,
 {
 	struct mmc_card *card;
 	int err;
+	int retries = 10;
 
 	BUG_ON(!host);
 	WARN_ON(!host->claimed);
 
+try_again:
+	if (!retries) {
+		pr_warning("%s: Skipping voltage switch\n",
+				mmc_hostname(host));
+		ocr &= ~R4_18V_PRESENT;
+		host->ocr &= ~R4_18V_PRESENT;
+	}
+
 	/*
 	 * Inform the card of the voltage
 	 */
@@ -645,14 +655,16 @@ static int mmc_sdio_init_card(struct mmc_host *host, u32 ocr,
 	 * systems that claim 1.8v signalling in fact do not support
 	 * it.
 	 */
-	if ((ocr & R4_18V_PRESENT) &&
-		(host->caps &
-			(MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 |
-			 MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 |
-			 MMC_CAP_UHS_DDR50))) {
-		err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180,
-				true);
-		if (err) {
+	if (!powered_resume && (ocr & R4_18V_PRESENT) && mmc_host_uhs(host)) {
+		err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180);
+		if (err == -EAGAIN) {
+			sdio_reset(host);
+			mmc_go_idle(host);
+			mmc_send_if_cond(host, host->ocr_avail);
+			mmc_remove_card(card);
+			retries--;
+			goto try_again;
+		} else if (err) {
 			ocr &= ~R4_18V_PRESENT;
 			host->ocr &= ~R4_18V_PRESENT;
 		}
@@ -937,10 +949,12 @@ static int mmc_sdio_resume(struct mmc_host *host)
 	mmc_claim_host(host);
 
 	/* No need to reinitialize powered-resumed nonremovable cards */
-	if (mmc_card_is_removable(host) || !mmc_card_keep_power(host))
+	if (mmc_card_is_removable(host) || !mmc_card_keep_power(host)) {
+		sdio_reset(host);
+		mmc_go_idle(host);
 		err = mmc_sdio_init_card(host, host->ocr, host->card,
 					mmc_card_keep_power(host));
-	else if (mmc_card_keep_power(host) && mmc_card_wake_sdio_irq(host)) {
+	} else if (mmc_card_keep_power(host) && mmc_card_wake_sdio_irq(host)) {
 		/* We may have switched to 1-bit mode during suspend */
 		err = sdio_enable_4bit_bus(host->card);
 		if (err > 0) {
@@ -1020,6 +1034,10 @@ static int mmc_sdio_power_restore(struct mmc_host *host)
 		goto out;
 	}
 
+	if (mmc_host_uhs(host))
+		/* to query card if 1.8V signalling is supported */
+		host->ocr |= R4_18V_PRESENT;
+
 	ret = mmc_sdio_init_card(host, host->ocr, host->card,
 				mmc_card_keep_power(host));
 	if (!ret && host->sdio_irqs)
@@ -1085,6 +1103,10 @@ int mmc_attach_sdio(struct mmc_host *host)
 	/*
 	 * Detect and init the card.
 	 */
+	if (mmc_host_uhs(host))
+		/* to query card if 1.8V signalling is supported */
+		host->ocr |= R4_18V_PRESENT;
+
 	err = mmc_sdio_init_card(host, host->ocr, NULL, 0);
 	if (err) {
 		if (err == -EAGAIN) {

drivers/mmc/core/slot-gpio.c

@@ -92,6 +92,20 @@ int mmc_gpio_get_cd(struct mmc_host *host)
 }
 EXPORT_SYMBOL(mmc_gpio_get_cd);
 
+/**
+ * mmc_gpio_request_ro - request a gpio for write-protection
+ * @host: mmc host
+ * @gpio: gpio number requested
+ *
+ * As devm_* managed functions are used in mmc_gpio_request_ro(), client
+ * drivers do not need to explicitly call mmc_gpio_free_ro() for freeing up,
+ * if the requesting and freeing are only needed at probing and unbinding time
+ * for once.  However, if client drivers do something special like runtime
+ * switching for write-protection, they are responsible for calling
+ * mmc_gpio_request_ro() and mmc_gpio_free_ro() as a pair on their own.
+ *
+ * Returns zero on success, else an error.
+ */
 int mmc_gpio_request_ro(struct mmc_host *host, unsigned int gpio)
 {
 	struct mmc_gpio *ctx;
@@ -106,7 +120,8 @@ int mmc_gpio_request_ro(struct mmc_host *host, unsigned int gpio)
 
 	ctx = host->slot.handler_priv;
 
-	ret = gpio_request_one(gpio, GPIOF_DIR_IN, ctx->ro_label);
+	ret = devm_gpio_request_one(&host->class_dev, gpio, GPIOF_DIR_IN,
+				    ctx->ro_label);
 	if (ret < 0)
 		return ret;
 
@@ -116,6 +131,20 @@ int mmc_gpio_request_ro(struct mmc_host *host, unsigned int gpio)
 }
 EXPORT_SYMBOL(mmc_gpio_request_ro);
 
+/**
+ * mmc_gpio_request_cd - request a gpio for card-detection
+ * @host: mmc host
+ * @gpio: gpio number requested
+ *
+ * As devm_* managed functions are used in mmc_gpio_request_cd(), client
+ * drivers do not need to explicitly call mmc_gpio_free_cd() for freeing up,
+ * if the requesting and freeing are only needed at probing and unbinding time
+ * for once.  However, if client drivers do something special like runtime
+ * switching for card-detection, they are responsible for calling
+ * mmc_gpio_request_cd() and mmc_gpio_free_cd() as a pair on their own.
+ *
+ * Returns zero on success, else an error.
+ */
 int mmc_gpio_request_cd(struct mmc_host *host, unsigned int gpio)
 {
 	struct mmc_gpio *ctx;
@@ -128,7 +157,8 @@ int mmc_gpio_request_cd(struct mmc_host *host, unsigned int gpio)
 
 	ctx = host->slot.handler_priv;
 
-	ret = gpio_request_one(gpio, GPIOF_DIR_IN, ctx->cd_label);
+	ret = devm_gpio_request_one(&host->class_dev, gpio, GPIOF_DIR_IN,
+				    ctx->cd_label);
 	if (ret < 0)
 		/*
 		 * don't bother freeing memory. It might still get used by other
@@ -146,7 +176,8 @@ int mmc_gpio_request_cd(struct mmc_host *host, unsigned int gpio)
 		irq = -EINVAL;
 
 	if (irq >= 0) {
-		ret = request_threaded_irq(irq, NULL, mmc_gpio_cd_irqt,
+		ret = devm_request_threaded_irq(&host->class_dev, irq,
+			NULL, mmc_gpio_cd_irqt,
 			IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
 			ctx->cd_label, host);
 		if (ret < 0)
@@ -164,6 +195,13 @@ int mmc_gpio_request_cd(struct mmc_host *host, unsigned int gpio)
 }
 EXPORT_SYMBOL(mmc_gpio_request_cd);
 
+/**
+ * mmc_gpio_free_ro - free the write-protection gpio
+ * @host: mmc host
+ *
+ * It's provided only for cases that client drivers need to manually free
+ * up the write-protection gpio requested by mmc_gpio_request_ro().
+ */
 void mmc_gpio_free_ro(struct mmc_host *host)
 {
 	struct mmc_gpio *ctx = host->slot.handler_priv;
@@ -175,10 +213,17 @@ void mmc_gpio_free_ro(struct mmc_host *host)
 	gpio = ctx->ro_gpio;
 	ctx->ro_gpio = -EINVAL;
 
-	gpio_free(gpio);
+	devm_gpio_free(&host->class_dev, gpio);
 }
 EXPORT_SYMBOL(mmc_gpio_free_ro);
 
+/**
+ * mmc_gpio_free_cd - free the card-detection gpio
+ * @host: mmc host
+ *
+ * It's provided only for cases that client drivers need to manually free
+ * up the card-detection gpio requested by mmc_gpio_request_cd().
+ */
 void mmc_gpio_free_cd(struct mmc_host *host)
 {
 	struct mmc_gpio *ctx = host->slot.handler_priv;
@@ -188,13 +233,13 @@ void mmc_gpio_free_cd(struct mmc_host *host)
 		return;
 
 	if (host->slot.cd_irq >= 0) {
-		free_irq(host->slot.cd_irq, host);
+		devm_free_irq(&host->class_dev, host->slot.cd_irq, host);
 		host->slot.cd_irq = -EINVAL;
 	}
 
 	gpio = ctx->cd_gpio;
 	ctx->cd_gpio = -EINVAL;
 
-	gpio_free(gpio);
+	devm_gpio_free(&host->class_dev, gpio);
 }
 EXPORT_SYMBOL(mmc_gpio_free_cd);

drivers/mmc/host/Kconfig

@@ -238,6 +238,17 @@ config MMC_SDHCI_S3C_DMA
 
 	  YMMV.
 
+config MMC_SDHCI_BCM2835
+	tristate "SDHCI platform support for the BCM2835 SD/MMC Controller"
+	depends on ARCH_BCM2835
+	depends on MMC_SDHCI_PLTFM
+	select MMC_SDHCI_IO_ACCESSORS
+	help
+	  This selects the BCM2835 SD/MMC controller. If you have a BCM2835
+	  platform with SD or MMC devices, say Y or M here.
+
+	  If unsure, say N.
+
 config MMC_OMAP
 	tristate "TI OMAP Multimedia Card Interface support"
 	depends on ARCH_OMAP
@@ -361,6 +372,13 @@ config MMC_DAVINCI
           If you have an DAVINCI board with a Multimedia Card slot,
           say Y or M here.  If unsure, say N.
 
+config MMC_GOLDFISH
+	tristate "goldfish qemu Multimedia Card Interface support"
+	depends on GOLDFISH
+	help
+	  This selects the Goldfish Multimedia card Interface emulation
+	  found on the Goldfish Android virtual device emulation.
+
 config MMC_SPI
 	tristate "MMC/SD/SDIO over SPI"
 	depends on SPI_MASTER && !HIGHMEM && HAS_DMA

drivers/mmc/host/Makefile

@@ -23,6 +23,7 @@ obj-$(CONFIG_MMC_TIFM_SD)	+= tifm_sd.o
 obj-$(CONFIG_MMC_MSM)		+= msm_sdcc.o
 obj-$(CONFIG_MMC_MVSDIO)	+= mvsdio.o
 obj-$(CONFIG_MMC_DAVINCI)       += davinci_mmc.o
+obj-$(CONFIG_MMC_GOLDFISH)	+= android-goldfish.o
 obj-$(CONFIG_MMC_SPI)		+= mmc_spi.o
 ifeq ($(CONFIG_OF),y)
 obj-$(CONFIG_MMC_SPI)		+= of_mmc_spi.o
@@ -58,6 +59,7 @@ obj-$(CONFIG_MMC_SDHCI_DOVE)		+= sdhci-dove.o
 obj-$(CONFIG_MMC_SDHCI_TEGRA)		+= sdhci-tegra.o
 obj-$(CONFIG_MMC_SDHCI_OF_ESDHC)	+= sdhci-of-esdhc.o
 obj-$(CONFIG_MMC_SDHCI_OF_HLWD)		+= sdhci-of-hlwd.o
+obj-$(CONFIG_MMC_SDHCI_BCM2835)		+= sdhci-bcm2835.o
 
 ifeq ($(CONFIG_CB710_DEBUG),y)
 	CFLAGS-cb710-mmc	+= -DDEBUG

drivers/mmc/host/dw_mmc-exynos.c

@@ -175,16 +175,6 @@ static int dw_mci_exynos_setup_bus(struct dw_mci *host,
 		}
 	}
 
-	gpio = of_get_named_gpio(slot_np, "wp-gpios", 0);
-	if (gpio_is_valid(gpio)) {
-		if (devm_gpio_request(host->dev, gpio, "dw-mci-wp"))
-			dev_info(host->dev, "gpio [%d] request failed\n",
-						gpio);
-	} else {
-		dev_info(host->dev, "wp gpio not available");
-		host->pdata->quirks |= DW_MCI_QUIRK_NO_WRITE_PROTECT;
-	}
-
 	if (host->pdata->quirks & DW_MCI_QUIRK_BROKEN_CARD_DETECTION)
 		return 0;
 

drivers/mmc/host/dw_mmc.c

@@ -34,6 +34,7 @@
 #include <linux/regulator/consumer.h>
 #include <linux/workqueue.h>
 #include <linux/of.h>
+#include <linux/of_gpio.h>
 
 #include "dw_mmc.h"
 
@@ -74,6 +75,8 @@ struct idmac_desc {
  * struct dw_mci_slot - MMC slot state
  * @mmc: The mmc_host representing this slot.
  * @host: The MMC controller this slot is using.
+ * @quirks: Slot-level quirks (DW_MCI_SLOT_QUIRK_XXX)
+ * @wp_gpio: If gpio_is_valid() we'll use this to read write protect.
  * @ctype: Card type for this slot.
  * @mrq: mmc_request currently being processed or waiting to be
  *	processed, or NULL when the slot is idle.
@@ -88,6 +91,9 @@ struct dw_mci_slot {
 	struct mmc_host		*mmc;
 	struct dw_mci		*host;
 
+	int			quirks;
+	int			wp_gpio;
+
 	u32			ctype;
 
 	struct mmc_request	*mrq;
@@ -825,10 +831,12 @@ static int dw_mci_get_ro(struct mmc_host *mmc)
 	struct dw_mci_board *brd = slot->host->pdata;
 
 	/* Use platform get_ro function, else try on board write protect */
-	if (brd->quirks & DW_MCI_QUIRK_NO_WRITE_PROTECT)
+	if (slot->quirks & DW_MCI_SLOT_QUIRK_NO_WRITE_PROTECT)
 		read_only = 0;
 	else if (brd->get_ro)
 		read_only = brd->get_ro(slot->id);
+	else if (gpio_is_valid(slot->wp_gpio))
+		read_only = gpio_get_value(slot->wp_gpio);
 	else
 		read_only =
 			mci_readl(slot->host, WRTPRT) & (1 << slot->id) ? 1 : 0;
@@ -1785,6 +1793,30 @@ static struct device_node *dw_mci_of_find_slot_node(struct device *dev, u8 slot)
 	return NULL;
 }
 
+static struct dw_mci_of_slot_quirks {
+	char *quirk;
+	int id;
+} of_slot_quirks[] = {
+	{
+		.quirk	= "disable-wp",
+		.id	= DW_MCI_SLOT_QUIRK_NO_WRITE_PROTECT,
+	},
+};
+
+static int dw_mci_of_get_slot_quirks(struct device *dev, u8 slot)
+{
+	struct device_node *np = dw_mci_of_find_slot_node(dev, slot);
+	int quirks = 0;
+	int idx;
+
+	/* get quirks */
+	for (idx = 0; idx < ARRAY_SIZE(of_slot_quirks); idx++)
+		if (of_get_property(np, of_slot_quirks[idx].quirk, NULL))
+			quirks |= of_slot_quirks[idx].id;
+
+	return quirks;
+}
+
 /* find out bus-width for a given slot */
 static u32 dw_mci_of_get_bus_wd(struct device *dev, u8 slot)
 {
@@ -1799,7 +1831,34 @@ static u32 dw_mci_of_get_bus_wd(struct device *dev, u8 slot)
 			       " as 1\n");
 	return bus_wd;
 }
+
+/* find the write protect gpio for a given slot; or -1 if none specified */
+static int dw_mci_of_get_wp_gpio(struct device *dev, u8 slot)
+{
+	struct device_node *np = dw_mci_of_find_slot_node(dev, slot);
+	int gpio;
+
+	if (!np)
+		return -EINVAL;
+
+	gpio = of_get_named_gpio(np, "wp-gpios", 0);
+
+	/* Having a missing entry is valid; return silently */
+	if (!gpio_is_valid(gpio))
+		return -EINVAL;
+
+	if (devm_gpio_request(dev, gpio, "dw-mci-wp")) {
+		dev_warn(dev, "gpio [%d] request failed\n", gpio);
+		return -EINVAL;
+	}
+
+	return gpio;
+}
 #else /* CONFIG_OF */
+static int dw_mci_of_get_slot_quirks(struct device *dev, u8 slot)
+{
+	return 0;
+}
 static u32 dw_mci_of_get_bus_wd(struct device *dev, u8 slot)
 {
 	return 1;
@@ -1808,6 +1867,10 @@ static struct device_node *dw_mci_of_find_slot_node(struct device *dev, u8 slot)
 {
 	return NULL;
 }
+static int dw_mci_of_get_wp_gpio(struct device *dev, u8 slot)
+{
+	return -EINVAL;
+}
 #endif /* CONFIG_OF */
 
 static int dw_mci_init_slot(struct dw_mci *host, unsigned int id)
@@ -1828,6 +1891,8 @@ static int dw_mci_init_slot(struct dw_mci *host, unsigned int id)
 	slot->host = host;
 	host->slot[id] = slot;
 
+	slot->quirks = dw_mci_of_get_slot_quirks(host->dev, slot->id);
+
 	mmc->ops = &dw_mci_ops;
 	mmc->f_min = DIV_ROUND_UP(host->bus_hz, 510);
 	mmc->f_max = host->bus_hz;
@@ -1923,6 +1988,8 @@ static int dw_mci_init_slot(struct dw_mci *host, unsigned int id)
 	else
 		clear_bit(DW_MMC_CARD_PRESENT, &slot->flags);
 
+	slot->wp_gpio = dw_mci_of_get_wp_gpio(host->dev, slot->id);
+
 	mmc_add_host(mmc);
 
 #if defined(CONFIG_DEBUG_FS)

drivers/mmc/host/mvsdio.c

@@ -21,7 +21,11 @@
 #include <linux/irq.h>
 #include <linux/clk.h>
 #include <linux/gpio.h>
+#include <linux/of_gpio.h>
+#include <linux/of_irq.h>
 #include <linux/mmc/host.h>
+#include <linux/mmc/slot-gpio.h>
+#include <linux/pinctrl/consumer.h>
 
 #include <asm/sizes.h>
 #include <asm/unaligned.h>
@@ -51,8 +55,6 @@ struct mvsd_host {
 	struct mmc_host *mmc;
 	struct device *dev;
 	struct clk *clk;
-	int gpio_card_detect;
-	int gpio_write_protect;
 };
 
 #define mvsd_write(offs, val)	writel(val, iobase + (offs))
@@ -538,13 +540,6 @@ static void mvsd_timeout_timer(unsigned long data)
 		mmc_request_done(host->mmc, mrq);
 }
 
-static irqreturn_t mvsd_card_detect_irq(int irq, void *dev)
-{
-	struct mvsd_host *host = dev;
-	mmc_detect_change(host->mmc, msecs_to_jiffies(100));
-	return IRQ_HANDLED;
-}
-
 static void mvsd_enable_sdio_irq(struct mmc_host *mmc, int enable)
 {
 	struct mvsd_host *host = mmc_priv(mmc);
@@ -564,20 +559,6 @@ static void mvsd_enable_sdio_irq(struct mmc_host *mmc, int enable)
 	spin_unlock_irqrestore(&host->lock, flags);
 }
 
-static int mvsd_get_ro(struct mmc_host *mmc)
-{
-	struct mvsd_host *host = mmc_priv(mmc);
-
-	if (host->gpio_write_protect)
-		return gpio_get_value(host->gpio_write_protect);
-
-	/*
-	 * Board doesn't support read only detection; let the mmc core
-	 * decide what to do.
-	 */
-	return -ENOSYS;
-}
-
 static void mvsd_power_up(struct mvsd_host *host)
 {
 	void __iomem *iobase = host->base;
@@ -674,7 +655,7 @@ static void mvsd_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 
 static const struct mmc_host_ops mvsd_ops = {
 	.request		= mvsd_request,
-	.get_ro			= mvsd_get_ro,
+	.get_ro			= mmc_gpio_get_ro,
 	.set_ios		= mvsd_set_ios,
 	.enable_sdio_irq	= mvsd_enable_sdio_irq,
 };
@@ -703,17 +684,18 @@ mv_conf_mbus_windows(struct mvsd_host *host,
 
 static int __init mvsd_probe(struct platform_device *pdev)
 {
+	struct device_node *np = pdev->dev.of_node;
 	struct mmc_host *mmc = NULL;
 	struct mvsd_host *host = NULL;
-	const struct mvsdio_platform_data *mvsd_data;
 	const struct mbus_dram_target_info *dram;
 	struct resource *r;
 	int ret, irq;
+	int gpio_card_detect, gpio_write_protect;
+	struct pinctrl *pinctrl;
 
 	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	irq = platform_get_irq(pdev, 0);
-	mvsd_data = pdev->dev.platform_data;
-	if (!r || irq < 0 || !mvsd_data)
+	if (!r || irq < 0)
 		return -ENXIO;
 
 	mmc = mmc_alloc_host(sizeof(struct mvsd_host), &pdev->dev);
@@ -725,8 +707,43 @@ static int __init mvsd_probe(struct platform_device *pdev)
 	host = mmc_priv(mmc);
 	host->mmc = mmc;
 	host->dev = &pdev->dev;
+
+	pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
+	if (IS_ERR(pinctrl))
+		dev_warn(&pdev->dev, "no pins associated\n");
+
+	/*
+	 * Some non-DT platforms do not pass a clock, and the clock
+	 * frequency is passed through platform_data. On DT platforms,
+	 * a clock must always be passed, even if there is no gatable
+	 * clock associated to the SDIO interface (it can simply be a
+	 * fixed rate clock).
+	 */
+	host->clk = devm_clk_get(&pdev->dev, NULL);
+	if (!IS_ERR(host->clk))
+		clk_prepare_enable(host->clk);
+
+	if (np) {
+		if (IS_ERR(host->clk)) {
+			dev_err(&pdev->dev, "DT platforms must have a clock associated\n");
+			ret = -EINVAL;
+			goto out;
+		}
+
+		host->base_clock = clk_get_rate(host->clk) / 2;
+		gpio_card_detect = of_get_named_gpio(np, "cd-gpios", 0);
+		gpio_write_protect = of_get_named_gpio(np, "wp-gpios", 0);
+	} else {
+		const struct mvsdio_platform_data *mvsd_data;
+		mvsd_data = pdev->dev.platform_data;
+		if (!mvsd_data) {
+			ret = -ENXIO;
+			goto out;
+		}
 		host->base_clock = mvsd_data->clock / 2;
-	host->clk = ERR_PTR(-EINVAL);
+		gpio_card_detect = mvsd_data->gpio_card_detect;
+		gpio_write_protect = mvsd_data->gpio_write_protect;
+	}
 
 	mmc->ops = &mvsd_ops;
 
@@ -765,43 +782,14 @@ static int __init mvsd_probe(struct platform_device *pdev)
 		goto out;
 	}
 
-	/* Not all platforms can gate the clock, so it is not
-	   an error if the clock does not exists. */
-	host->clk = devm_clk_get(&pdev->dev, NULL);
-	if (!IS_ERR(host->clk))
-		clk_prepare_enable(host->clk);
-
-	if (mvsd_data->gpio_card_detect) {
-		ret = devm_gpio_request_one(&pdev->dev,
-					    mvsd_data->gpio_card_detect,
-					    GPIOF_IN, DRIVER_NAME " cd");
-		if (ret == 0) {
-			irq = gpio_to_irq(mvsd_data->gpio_card_detect);
-			ret = devm_request_irq(&pdev->dev, irq,
-					       mvsd_card_detect_irq,
-					       IRQ_TYPE_EDGE_RISING |
-					       IRQ_TYPE_EDGE_FALLING,
-					       DRIVER_NAME " cd", host);
-			if (ret == 0)
-				host->gpio_card_detect =
-					mvsd_data->gpio_card_detect;
-			else
-				devm_gpio_free(&pdev->dev,
-					       mvsd_data->gpio_card_detect);
-		}
-	}
-	if (!host->gpio_card_detect)
+	if (gpio_is_valid(gpio_card_detect)) {
+		ret = mmc_gpio_request_cd(mmc, gpio_card_detect);
+		if (ret)
+			goto out;
+	} else
 		mmc->caps |= MMC_CAP_NEEDS_POLL;
 
-	if (mvsd_data->gpio_write_protect) {
-		ret = devm_gpio_request_one(&pdev->dev,
-					    mvsd_data->gpio_write_protect,
-					    GPIOF_IN, DRIVER_NAME " wp");
-		if (ret == 0) {
-			host->gpio_write_protect =
-				mvsd_data->gpio_write_protect;
-		}
-	}
+	mmc_gpio_request_ro(mmc, gpio_write_protect);
 
 	setup_timer(&host->timer, mvsd_timeout_timer, (unsigned long)host);
 	platform_set_drvdata(pdev, mmc);
@@ -811,15 +799,17 @@ static int __init mvsd_probe(struct platform_device *pdev)
 
 	pr_notice("%s: %s driver initialized, ",
 			   mmc_hostname(mmc), DRIVER_NAME);
-	if (host->gpio_card_detect)
+	if (!(mmc->caps & MMC_CAP_NEEDS_POLL))
 		printk("using GPIO %d for card detection\n",
-		       host->gpio_card_detect);
+		       gpio_card_detect);
 	else
 		printk("lacking card detect (fall back to polling)\n");
 	return 0;
 
 out:
 	if (mmc) {
+		mmc_gpio_free_cd(mmc);
+		mmc_gpio_free_ro(mmc);
 		if (!IS_ERR(host->clk))
 			clk_disable_unprepare(host->clk);
 		mmc_free_host(mmc);
@@ -834,6 +824,8 @@ static int __exit mvsd_remove(struct platform_device *pdev)
 
 	struct mvsd_host *host = mmc_priv(mmc);
 
+	mmc_gpio_free_cd(mmc);
+	mmc_gpio_free_ro(mmc);
 	mmc_remove_host(mmc);
 	del_timer_sync(&host->timer);
 	mvsd_power_down(host);
@@ -873,12 +865,19 @@ static int mvsd_resume(struct platform_device *dev)
 #define mvsd_resume	NULL
 #endif
 
+static const struct of_device_id mvsdio_dt_ids[] = {
+	{ .compatible = "marvell,orion-sdio" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mvsdio_dt_ids);
+
 static struct platform_driver mvsd_driver = {
 	.remove		= __exit_p(mvsd_remove),
 	.suspend	= mvsd_suspend,
 	.resume		= mvsd_resume,
 	.driver		= {
 		.name	= DRIVER_NAME,
+		.of_match_table = mvsdio_dt_ids,
 	},
 };
 

drivers/mmc/host/mxs-mmc.c

@@ -354,7 +354,7 @@ static void mxs_mmc_adtc(struct mxs_mmc_host *host)
 	struct dma_async_tx_descriptor *desc;
 	struct scatterlist *sgl = data->sg, *sg;
 	unsigned int sg_len = data->sg_len;
-	int i;
+	unsigned int i;
 
 	unsigned short dma_data_dir, timeout;
 	enum dma_transfer_direction slave_dirn;
@@ -804,3 +804,4 @@ module_platform_driver(mxs_mmc_driver);
 MODULE_DESCRIPTION("FREESCALE MXS MMC peripheral");
 MODULE_AUTHOR("Freescale Semiconductor");
 MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:" DRIVER_NAME);

drivers/mmc/host/of_mmc_spi.c

@@ -146,7 +146,7 @@ struct mmc_spi_platform_data *mmc_spi_get_pdata(struct spi_device *spi)
 		oms->pdata.get_ro = of_mmc_spi_get_ro;
 
 	oms->detect_irq = irq_of_parse_and_map(np, 0);
-	if (oms->detect_irq != NO_IRQ) {
+	if (oms->detect_irq != 0) {
 		oms->pdata.init = of_mmc_spi_init;
 		oms->pdata.exit = of_mmc_spi_exit;
 	} else {

drivers/mmc/host/rtsx_pci_sdmmc.c

@@ -1097,11 +1097,6 @@ static int sdmmc_switch_voltage(struct mmc_host *mmc, struct mmc_ios *ios)
 		voltage = OUTPUT_1V8;
 
 	if (voltage == OUTPUT_1V8) {
-		err = rtsx_pci_write_register(pcr,
-				SD30_DRIVE_SEL, 0x07, DRIVER_TYPE_B);
-		if (err < 0)
-			goto out;
-
 		err = sd_wait_voltage_stable_1(host);
 		if (err < 0)
 			goto out;

drivers/mmc/host/sdhci-bcm2835.c

+/*
+ * BCM2835 SDHCI
+ * Copyright (C) 2012 Stephen Warren
+ * Based on U-Boot's MMC driver for the BCM2835 by Oleksandr Tymoshenko & me
+ * Portions of the code there were obviously based on the Linux kernel at:
+ * git://github.com/raspberrypi/linux.git rpi-3.6.y
+ * commit f5b930b "Main bcm2708 linux port" signed-off-by Dom Cobley.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/mmc/host.h>
+#include "sdhci-pltfm.h"
+
+/*
+ * 400KHz is max freq for card ID etc. Use that as min card clock. We need to
+ * know the min to enable static calculation of max BCM2835_SDHCI_WRITE_DELAY.
+ */
+#define MIN_FREQ 400000
+
+/*
+ * The Arasan has a bugette whereby it may lose the content of successive
+ * writes to registers that are within two SD-card clock cycles of each other
+ * (a clock domain crossing problem). It seems, however, that the data
+ * register does not have this problem, which is just as well - otherwise we'd
+ * have to nobble the DMA engine too.
+ *
+ * This should probably be dynamically calculated based on the actual card
+ * frequency. However, this is the longest we'll have to wait, and doesn't
+ * seem to slow access down too much, so the added complexity doesn't seem
+ * worth it for now.
+ *
+ * 1/MIN_FREQ is (max) time per tick of eMMC clock.
+ * 2/MIN_FREQ is time for two ticks.
+ * Multiply by 1000000 to get uS per two ticks.
+ * *1000000 for uSecs.
+ * +1 for hack rounding.
+ */
+#define BCM2835_SDHCI_WRITE_DELAY	(((2 * 1000000) / MIN_FREQ) + 1)
+
+struct bcm2835_sdhci {
+	u32 shadow;
+};
+
+static void bcm2835_sdhci_writel(struct sdhci_host *host, u32 val, int reg)
+{
+	writel(val, host->ioaddr + reg);
+
+	udelay(BCM2835_SDHCI_WRITE_DELAY);
+}
+
+static inline u32 bcm2835_sdhci_readl(struct sdhci_host *host, int reg)
+{
+	u32 val = readl(host->ioaddr + reg);
+
+	if (reg == SDHCI_CAPABILITIES)
+		val |= SDHCI_CAN_VDD_330;
+
+	return val;
+}
+
+static void bcm2835_sdhci_writew(struct sdhci_host *host, u16 val, int reg)
+{
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct bcm2835_sdhci *bcm2835_host = pltfm_host->priv;
+	u32 oldval = (reg == SDHCI_COMMAND) ? bcm2835_host->shadow :
+		bcm2835_sdhci_readl(host, reg & ~3);
+	u32 word_num = (reg >> 1) & 1;
+	u32 word_shift = word_num * 16;
+	u32 mask = 0xffff << word_shift;
+	u32 newval = (oldval & ~mask) | (val << word_shift);
+
+	if (reg == SDHCI_TRANSFER_MODE)
+		bcm2835_host->shadow = newval;
+	else
+		bcm2835_sdhci_writel(host, newval, reg & ~3);
+}
+
+static u16 bcm2835_sdhci_readw(struct sdhci_host *host, int reg)
+{
+	u32 val = bcm2835_sdhci_readl(host, (reg & ~3));
+	u32 word_num = (reg >> 1) & 1;
+	u32 word_shift = word_num * 16;
+	u32 word = (val >> word_shift) & 0xffff;
+
+	return word;
+}
+
+static void bcm2835_sdhci_writeb(struct sdhci_host *host, u8 val, int reg)
+{
+	u32 oldval = bcm2835_sdhci_readl(host, reg & ~3);
+	u32 byte_num = reg & 3;
+	u32 byte_shift = byte_num * 8;
+	u32 mask = 0xff << byte_shift;
+	u32 newval = (oldval & ~mask) | (val << byte_shift);
+
+	bcm2835_sdhci_writel(host, newval, reg & ~3);
+}
+
+static u8 bcm2835_sdhci_readb(struct sdhci_host *host, int reg)
+{
+	u32 val = bcm2835_sdhci_readl(host, (reg & ~3));
+	u32 byte_num = reg & 3;
+	u32 byte_shift = byte_num * 8;
+	u32 byte = (val >> byte_shift) & 0xff;
+
+	return byte;
+}
+
+unsigned int bcm2835_sdhci_get_min_clock(struct sdhci_host *host)
+{
+	return MIN_FREQ;
+}
+
+static struct sdhci_ops bcm2835_sdhci_ops = {
+	.write_l = bcm2835_sdhci_writel,
+	.write_w = bcm2835_sdhci_writew,
+	.write_b = bcm2835_sdhci_writeb,
+	.read_l = bcm2835_sdhci_readl,
+	.read_w = bcm2835_sdhci_readw,
+	.read_b = bcm2835_sdhci_readb,
+	.get_max_clock = sdhci_pltfm_clk_get_max_clock,
+	.get_min_clock = bcm2835_sdhci_get_min_clock,
+};
+
+static struct sdhci_pltfm_data bcm2835_sdhci_pdata = {
+	.quirks = SDHCI_QUIRK_BROKEN_CARD_DETECTION |
+		  SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK,
+	.ops = &bcm2835_sdhci_ops,
+};
+
+static int bcm2835_sdhci_probe(struct platform_device *pdev)
+{
+	struct sdhci_host *host;
+	struct bcm2835_sdhci *bcm2835_host;
+	struct sdhci_pltfm_host *pltfm_host;
+	int ret;
+
+	host = sdhci_pltfm_init(pdev, &bcm2835_sdhci_pdata);
+	if (IS_ERR(host))
+		return PTR_ERR(host);
+
+	bcm2835_host = devm_kzalloc(&pdev->dev, sizeof(*bcm2835_host),
+					GFP_KERNEL);
+	if (!bcm2835_host) {
+		dev_err(mmc_dev(host->mmc),
+			"failed to allocate bcm2835_sdhci\n");
+		return -ENOMEM;
+	}
+
+	pltfm_host = sdhci_priv(host);
+	pltfm_host->priv = bcm2835_host;
+
+	pltfm_host->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(pltfm_host->clk)) {
+		ret = PTR_ERR(pltfm_host->clk);
+		goto err;
+	}
+
+	return sdhci_add_host(host);
+
+err:
+	sdhci_pltfm_free(pdev);
+	return ret;
+}
+
+static int bcm2835_sdhci_remove(struct platform_device *pdev)
+{
+	struct sdhci_host *host = platform_get_drvdata(pdev);
+	int dead = (readl(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff);
+
+	sdhci_remove_host(host, dead);
+	sdhci_pltfm_free(pdev);
+
+	return 0;
+}
+
+static const struct of_device_id bcm2835_sdhci_of_match[] = {
+	{ .compatible = "brcm,bcm2835-sdhci" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, bcm2835_sdhci_of_match);
+
+static struct platform_driver bcm2835_sdhci_driver = {
+	.driver = {
+		.name = "sdhci-bcm2835",
+		.owner = THIS_MODULE,
+		.of_match_table = bcm2835_sdhci_of_match,
+		.pm = SDHCI_PLTFM_PMOPS,
+	},
+	.probe = bcm2835_sdhci_probe,
+	.remove = bcm2835_sdhci_remove,
+};
+module_platform_driver(bcm2835_sdhci_driver);
+
+MODULE_DESCRIPTION("BCM2835 SDHCI driver");
+MODULE_AUTHOR("Stephen Warren");
+MODULE_LICENSE("GPL v2");

drivers/mmc/host/sdhci-pci.c

@@ -935,7 +935,7 @@ static int sdhci_pci_enable_dma(struct sdhci_host *host)
 	return 0;
 }
 
-static int sdhci_pci_8bit_width(struct sdhci_host *host, int width)
+static int sdhci_pci_bus_width(struct sdhci_host *host, int width)
 {
 	u8 ctrl;
 
@@ -977,7 +977,7 @@ static void sdhci_pci_hw_reset(struct sdhci_host *host)
 
 static struct sdhci_ops sdhci_pci_ops = {
 	.enable_dma	= sdhci_pci_enable_dma,
-	.platform_8bit_width	= sdhci_pci_8bit_width,
+	.platform_bus_width	= sdhci_pci_bus_width,
 	.hw_reset		= sdhci_pci_hw_reset,
 };
 

drivers/mmc/host/sdhci-pltfm.c

@@ -36,6 +36,14 @@
 #endif
 #include "sdhci-pltfm.h"
 
+unsigned int sdhci_pltfm_clk_get_max_clock(struct sdhci_host *host)
+{
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+
+	return clk_get_rate(pltfm_host->clk);
+}
+EXPORT_SYMBOL_GPL(sdhci_pltfm_clk_get_max_clock);
+
 static struct sdhci_ops sdhci_pltfm_ops = {
 };
 

drivers/mmc/host/sdhci-pltfm.h

@@ -98,6 +98,8 @@ extern int sdhci_pltfm_register(struct platform_device *pdev,
 				struct sdhci_pltfm_data *pdata);
 extern int sdhci_pltfm_unregister(struct platform_device *pdev);
 
+extern unsigned int sdhci_pltfm_clk_get_max_clock(struct sdhci_host *host);
+
 #ifdef CONFIG_PM
 extern const struct dev_pm_ops sdhci_pltfm_pmops;
 #define SDHCI_PLTFM_PMOPS (&sdhci_pltfm_pmops)

drivers/mmc/host/sdhci-pxav2.c

@@ -111,17 +111,10 @@ static int pxav2_mmc_set_width(struct sdhci_host *host, int width)
 	return 0;
 }
 
-static u32 pxav2_get_max_clock(struct sdhci_host *host)
-{
-	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
-
-	return clk_get_rate(pltfm_host->clk);
-}
-
 static struct sdhci_ops pxav2_sdhci_ops = {
-	.get_max_clock = pxav2_get_max_clock,
+	.get_max_clock = sdhci_pltfm_clk_get_max_clock,
 	.platform_reset_exit = pxav2_set_private_registers,
-	.platform_8bit_width = pxav2_mmc_set_width,
+	.platform_bus_width = pxav2_mmc_set_width,
 };
 
 #ifdef CONFIG_OF

drivers/mmc/host/sdhci-pxav3.c

@@ -32,10 +32,14 @@
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/of_gpio.h>
+#include <linux/pm.h>
+#include <linux/pm_runtime.h>
 
 #include "sdhci.h"
 #include "sdhci-pltfm.h"
 
+#define PXAV3_RPM_DELAY_MS     50
+
 #define SD_CLOCK_BURST_SIZE_SETUP		0x10A
 #define SDCLK_SEL	0x100
 #define SDCLK_DELAY_SHIFT	9
@@ -163,18 +167,11 @@ static int pxav3_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs)
 	return 0;
 }
 
-static u32 pxav3_get_max_clock(struct sdhci_host *host)
-{
-	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
-
-	return clk_get_rate(pltfm_host->clk);
-}
-
 static struct sdhci_ops pxav3_sdhci_ops = {
 	.platform_reset_exit = pxav3_set_private_registers,
 	.set_uhs_signaling = pxav3_set_uhs_signaling,
 	.platform_send_init_74_clocks = pxav3_gen_init_74_clocks,
-	.get_max_clock = pxav3_get_max_clock,
+	.get_max_clock = sdhci_pltfm_clk_get_max_clock,
 };
 
 #ifdef CONFIG_OF
@@ -303,20 +300,37 @@ static int sdhci_pxav3_probe(struct platform_device *pdev)
 
 	sdhci_get_of_property(pdev);
 
+	pm_runtime_set_active(&pdev->dev);
+	pm_runtime_enable(&pdev->dev);
+	pm_runtime_set_autosuspend_delay(&pdev->dev, PXAV3_RPM_DELAY_MS);
+	pm_runtime_use_autosuspend(&pdev->dev);
+	pm_suspend_ignore_children(&pdev->dev, 1);
+	pm_runtime_get_noresume(&pdev->dev);
+
 	ret = sdhci_add_host(host);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to add host\n");
+		pm_runtime_forbid(&pdev->dev);
+		pm_runtime_disable(&pdev->dev);
 		goto err_add_host;
 	}
 
 	platform_set_drvdata(pdev, host);
 
+	if (pdata->pm_caps & MMC_PM_KEEP_POWER) {
+		device_init_wakeup(&pdev->dev, 1);
+		host->mmc->pm_flags |= MMC_PM_WAKE_SDIO_IRQ;
+	} else {
+		device_init_wakeup(&pdev->dev, 0);
+	}
+
+	pm_runtime_put_autosuspend(&pdev->dev);
+
 	return 0;
 
 err_add_host:
 	clk_disable_unprepare(clk);
 	clk_put(clk);
-	mmc_gpio_free_cd(host->mmc);
 err_cd_req:
 err_clk_get:
 	sdhci_pltfm_free(pdev);
@@ -329,16 +343,14 @@ static int sdhci_pxav3_remove(struct platform_device *pdev)
 	struct sdhci_host *host = platform_get_drvdata(pdev);
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct sdhci_pxa *pxa = pltfm_host->priv;
-	struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data;
 
+	pm_runtime_get_sync(&pdev->dev);
 	sdhci_remove_host(host, 1);
+	pm_runtime_disable(&pdev->dev);
 
 	clk_disable_unprepare(pltfm_host->clk);
 	clk_put(pltfm_host->clk);
 
-	if (gpio_is_valid(pdata->ext_cd_gpio))
-		mmc_gpio_free_cd(host->mmc);
-
 	sdhci_pltfm_free(pdev);
 	kfree(pxa);
 
@@ -347,6 +359,83 @@ static int sdhci_pxav3_remove(struct platform_device *pdev)
 	return 0;
 }
 
+#ifdef CONFIG_PM_SLEEP
+static int sdhci_pxav3_suspend(struct device *dev)
+{
+	int ret;
+	struct sdhci_host *host = dev_get_drvdata(dev);
+
+	pm_runtime_get_sync(dev);
+	ret = sdhci_suspend_host(host);
+	pm_runtime_mark_last_busy(dev);
+	pm_runtime_put_autosuspend(dev);
+
+	return ret;
+}
+
+static int sdhci_pxav3_resume(struct device *dev)
+{
+	int ret;
+	struct sdhci_host *host = dev_get_drvdata(dev);
+
+	pm_runtime_get_sync(dev);
+	ret = sdhci_resume_host(host);
+	pm_runtime_mark_last_busy(dev);
+	pm_runtime_put_autosuspend(dev);
+
+	return ret;
+}
+#endif
+
+#ifdef CONFIG_PM_RUNTIME
+static int sdhci_pxav3_runtime_suspend(struct device *dev)
+{
+	struct sdhci_host *host = dev_get_drvdata(dev);
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	unsigned long flags;
+
+	if (pltfm_host->clk) {
+		spin_lock_irqsave(&host->lock, flags);
+		host->runtime_suspended = true;
+		spin_unlock_irqrestore(&host->lock, flags);
+
+		clk_disable_unprepare(pltfm_host->clk);
+	}
+
+	return 0;
+}
+
+static int sdhci_pxav3_runtime_resume(struct device *dev)
+{
+	struct sdhci_host *host = dev_get_drvdata(dev);
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	unsigned long flags;
+
+	if (pltfm_host->clk) {
+		clk_prepare_enable(pltfm_host->clk);
+
+		spin_lock_irqsave(&host->lock, flags);
+		host->runtime_suspended = false;
+		spin_unlock_irqrestore(&host->lock, flags);
+	}
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_PM
+static const struct dev_pm_ops sdhci_pxav3_pmops = {
+	SET_SYSTEM_SLEEP_PM_OPS(sdhci_pxav3_suspend, sdhci_pxav3_resume)
+	SET_RUNTIME_PM_OPS(sdhci_pxav3_runtime_suspend,
+		sdhci_pxav3_runtime_resume, NULL)
+};
+
+#define SDHCI_PXAV3_PMOPS (&sdhci_pxav3_pmops)
+
+#else
+#define SDHCI_PXAV3_PMOPS NULL
+#endif
+
 static struct platform_driver sdhci_pxav3_driver = {
 	.driver		= {
 		.name	= "sdhci-pxav3",
@@ -354,7 +443,7 @@ static struct platform_driver sdhci_pxav3_driver = {
 		.of_match_table = sdhci_pxav3_of_match,
 #endif
 		.owner	= THIS_MODULE,
-		.pm	= SDHCI_PLTFM_PMOPS,
+		.pm	= SDHCI_PXAV3_PMOPS,
 	},
 	.probe		= sdhci_pxav3_probe,
 	.remove		= sdhci_pxav3_remove,

drivers/mmc/host/sdhci-s3c.c

@@ -332,14 +332,14 @@ static void sdhci_cmu_set_clock(struct sdhci_host *host, unsigned int clock)
 }
 
 /**
- * sdhci_s3c_platform_8bit_width - support 8bit buswidth
+ * sdhci_s3c_platform_bus_width - support 8bit buswidth
  * @host: The SDHCI host being queried
  * @width: MMC_BUS_WIDTH_ macro for the bus width being requested
  *
  * We have 8-bit width support but is not a v3 controller.
- * So we add platform_8bit_width() and support 8bit width.
+ * So we add platform_bus_width() and support 8bit width.
  */
-static int sdhci_s3c_platform_8bit_width(struct sdhci_host *host, int width)
+static int sdhci_s3c_platform_bus_width(struct sdhci_host *host, int width)
 {
 	u8 ctrl;
 
@@ -369,7 +369,7 @@ static struct sdhci_ops sdhci_s3c_ops = {
 	.get_max_clock		= sdhci_s3c_get_max_clk,
 	.set_clock		= sdhci_s3c_set_clock,
 	.get_min_clock		= sdhci_s3c_get_min_clock,
-	.platform_8bit_width	= sdhci_s3c_platform_8bit_width,
+	.platform_bus_width	= sdhci_s3c_platform_bus_width,
 };
 
 static void sdhci_s3c_notify_change(struct platform_device *dev, int state)

drivers/mmc/host/sdhci-tegra.c

@@ -27,8 +27,6 @@
 
 #include <asm/gpio.h>
 
-#include <linux/platform_data/mmc-sdhci-tegra.h>
-
 #include "sdhci-pltfm.h"
 
 /* Tegra SDHOST controller vendor register definitions */
@@ -45,8 +43,11 @@ struct sdhci_tegra_soc_data {
 };
 
 struct sdhci_tegra {
-	const struct tegra_sdhci_platform_data *plat;
 	const struct sdhci_tegra_soc_data *soc_data;
+	int cd_gpio;
+	int wp_gpio;
+	int power_gpio;
+	int is_8bit;
 };
 
 static u32 tegra_sdhci_readl(struct sdhci_host *host, int reg)
@@ -108,12 +109,11 @@ static unsigned int tegra_sdhci_get_ro(struct sdhci_host *host)
 {
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct sdhci_tegra *tegra_host = pltfm_host->priv;
-	const struct tegra_sdhci_platform_data *plat = tegra_host->plat;
 
-	if (!gpio_is_valid(plat->wp_gpio))
+	if (!gpio_is_valid(tegra_host->wp_gpio))
 		return -1;
 
-	return gpio_get_value(plat->wp_gpio);
+	return gpio_get_value(tegra_host->wp_gpio);
 }
 
 static irqreturn_t carddetect_irq(int irq, void *data)
@@ -143,15 +143,14 @@ static void tegra_sdhci_reset_exit(struct sdhci_host *host, u8 mask)
 	}
 }
 
-static int tegra_sdhci_8bit(struct sdhci_host *host, int bus_width)
+static int tegra_sdhci_buswidth(struct sdhci_host *host, int bus_width)
 {
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct sdhci_tegra *tegra_host = pltfm_host->priv;
-	const struct tegra_sdhci_platform_data *plat = tegra_host->plat;
 	u32 ctrl;
 
 	ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
-	if (plat->is_8bit && bus_width == MMC_BUS_WIDTH_8) {
+	if (tegra_host->is_8bit && bus_width == MMC_BUS_WIDTH_8) {
 		ctrl &= ~SDHCI_CTRL_4BITBUS;
 		ctrl |= SDHCI_CTRL_8BITBUS;
 	} else {
@@ -170,7 +169,7 @@ static struct sdhci_ops tegra_sdhci_ops = {
 	.read_l     = tegra_sdhci_readl,
 	.read_w     = tegra_sdhci_readw,
 	.write_l    = tegra_sdhci_writel,
-	.platform_8bit_width = tegra_sdhci_8bit,
+	.platform_bus_width = tegra_sdhci_buswidth,
 	.platform_reset_exit = tegra_sdhci_reset_exit,
 };
 
@@ -217,31 +216,19 @@ static const struct of_device_id sdhci_tegra_dt_match[] = {
 };
 MODULE_DEVICE_TABLE(of, sdhci_dt_ids);
 
-static struct tegra_sdhci_platform_data *sdhci_tegra_dt_parse_pdata(
-						struct platform_device *pdev)
+static void sdhci_tegra_parse_dt(struct device *dev,
+					struct sdhci_tegra *tegra_host)
 {
-	struct tegra_sdhci_platform_data *plat;
-	struct device_node *np = pdev->dev.of_node;
+	struct device_node *np = dev->of_node;
 	u32 bus_width;
 
-	if (!np)
-		return NULL;
-
-	plat = devm_kzalloc(&pdev->dev, sizeof(*plat), GFP_KERNEL);
-	if (!plat) {
-		dev_err(&pdev->dev, "Can't allocate platform data\n");
-		return NULL;
-	}
-
-	plat->cd_gpio = of_get_named_gpio(np, "cd-gpios", 0);
-	plat->wp_gpio = of_get_named_gpio(np, "wp-gpios", 0);
-	plat->power_gpio = of_get_named_gpio(np, "power-gpios", 0);
+	tegra_host->cd_gpio = of_get_named_gpio(np, "cd-gpios", 0);
+	tegra_host->wp_gpio = of_get_named_gpio(np, "wp-gpios", 0);
+	tegra_host->power_gpio = of_get_named_gpio(np, "power-gpios", 0);
 
 	if (of_property_read_u32(np, "bus-width", &bus_width) == 0 &&
 	    bus_width == 8)
-		plat->is_8bit = 1;
-
-	return plat;
+		tegra_host->is_8bit = 1;
 }
 
 static int sdhci_tegra_probe(struct platform_device *pdev)
@@ -250,7 +237,6 @@ static int sdhci_tegra_probe(struct platform_device *pdev)
 	const struct sdhci_tegra_soc_data *soc_data;
 	struct sdhci_host *host;
 	struct sdhci_pltfm_host *pltfm_host;
-	struct tegra_sdhci_platform_data *plat;
 	struct sdhci_tegra *tegra_host;
 	struct clk *clk;
 	int rc;
@@ -263,52 +249,40 @@ static int sdhci_tegra_probe(struct platform_device *pdev)
 	host = sdhci_pltfm_init(pdev, soc_data->pdata);
 	if (IS_ERR(host))
 		return PTR_ERR(host);
-
 	pltfm_host = sdhci_priv(host);
 
-	plat = pdev->dev.platform_data;
-
-	if (plat == NULL)
-		plat = sdhci_tegra_dt_parse_pdata(pdev);
-
-	if (plat == NULL) {
-		dev_err(mmc_dev(host->mmc), "missing platform data\n");
-		rc = -ENXIO;
-		goto err_no_plat;
-	}
-
 	tegra_host = devm_kzalloc(&pdev->dev, sizeof(*tegra_host), GFP_KERNEL);
 	if (!tegra_host) {
 		dev_err(mmc_dev(host->mmc), "failed to allocate tegra_host\n");
 		rc = -ENOMEM;
-		goto err_no_plat;
+		goto err_alloc_tegra_host;
 	}
-
-	tegra_host->plat = plat;
 	tegra_host->soc_data = soc_data;
-
 	pltfm_host->priv = tegra_host;
 
-	if (gpio_is_valid(plat->power_gpio)) {
-		rc = gpio_request(plat->power_gpio, "sdhci_power");
+	sdhci_tegra_parse_dt(&pdev->dev, tegra_host);
+
+	if (gpio_is_valid(tegra_host->power_gpio)) {
+		rc = gpio_request(tegra_host->power_gpio, "sdhci_power");
 		if (rc) {
 			dev_err(mmc_dev(host->mmc),
 				"failed to allocate power gpio\n");
 			goto err_power_req;
 		}
-		gpio_direction_output(plat->power_gpio, 1);
+		gpio_direction_output(tegra_host->power_gpio, 1);
 	}
 
-	if (gpio_is_valid(plat->cd_gpio)) {
-		rc = gpio_request(plat->cd_gpio, "sdhci_cd");
+	if (gpio_is_valid(tegra_host->cd_gpio)) {
+		rc = gpio_request(tegra_host->cd_gpio, "sdhci_cd");
 		if (rc) {
 			dev_err(mmc_dev(host->mmc),
 				"failed to allocate cd gpio\n");
 			goto err_cd_req;
 		}
-		gpio_direction_input(plat->cd_gpio);
+		gpio_direction_input(tegra_host->cd_gpio);
 
-		rc = request_irq(gpio_to_irq(plat->cd_gpio), carddetect_irq,
+		rc = request_irq(gpio_to_irq(tegra_host->cd_gpio),
+				 carddetect_irq,
 				 IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
 				 mmc_hostname(host->mmc), host);
 
@@ -319,14 +293,14 @@ static int sdhci_tegra_probe(struct platform_device *pdev)
 
 	}
 
-	if (gpio_is_valid(plat->wp_gpio)) {
-		rc = gpio_request(plat->wp_gpio, "sdhci_wp");
+	if (gpio_is_valid(tegra_host->wp_gpio)) {
+		rc = gpio_request(tegra_host->wp_gpio, "sdhci_wp");
 		if (rc) {
 			dev_err(mmc_dev(host->mmc),
 				"failed to allocate wp gpio\n");
 			goto err_wp_req;
 		}
-		gpio_direction_input(plat->wp_gpio);
+		gpio_direction_input(tegra_host->wp_gpio);
 	}
 
 	clk = clk_get(mmc_dev(host->mmc), NULL);
@@ -338,9 +312,7 @@ static int sdhci_tegra_probe(struct platform_device *pdev)
 	clk_prepare_enable(clk);
 	pltfm_host->clk = clk;
 
-	host->mmc->pm_caps = plat->pm_flags;
-
-	if (plat->is_8bit)
+	if (tegra_host->is_8bit)
 		host->mmc->caps |= MMC_CAP_8_BIT_DATA;
 
 	rc = sdhci_add_host(host);
@@ -353,19 +325,19 @@ static int sdhci_tegra_probe(struct platform_device *pdev)
 	clk_disable_unprepare(pltfm_host->clk);
 	clk_put(pltfm_host->clk);
 err_clk_get:
-	if (gpio_is_valid(plat->wp_gpio))
-		gpio_free(plat->wp_gpio);
+	if (gpio_is_valid(tegra_host->wp_gpio))
+		gpio_free(tegra_host->wp_gpio);
 err_wp_req:
-	if (gpio_is_valid(plat->cd_gpio))
-		free_irq(gpio_to_irq(plat->cd_gpio), host);
+	if (gpio_is_valid(tegra_host->cd_gpio))
+		free_irq(gpio_to_irq(tegra_host->cd_gpio), host);
 err_cd_irq_req:
-	if (gpio_is_valid(plat->cd_gpio))
-		gpio_free(plat->cd_gpio);
+	if (gpio_is_valid(tegra_host->cd_gpio))
+		gpio_free(tegra_host->cd_gpio);
 err_cd_req:
-	if (gpio_is_valid(plat->power_gpio))
-		gpio_free(plat->power_gpio);
+	if (gpio_is_valid(tegra_host->power_gpio))
+		gpio_free(tegra_host->power_gpio);
 err_power_req:
-err_no_plat:
+err_alloc_tegra_host:
 	sdhci_pltfm_free(pdev);
 	return rc;
 }
@@ -375,21 +347,20 @@ static int sdhci_tegra_remove(struct platform_device *pdev)
 	struct sdhci_host *host = platform_get_drvdata(pdev);
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct sdhci_tegra *tegra_host = pltfm_host->priv;
-	const struct tegra_sdhci_platform_data *plat = tegra_host->plat;
 	int dead = (readl(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff);
 
 	sdhci_remove_host(host, dead);
 
-	if (gpio_is_valid(plat->wp_gpio))
-		gpio_free(plat->wp_gpio);
+	if (gpio_is_valid(tegra_host->wp_gpio))
+		gpio_free(tegra_host->wp_gpio);
 
-	if (gpio_is_valid(plat->cd_gpio)) {
-		free_irq(gpio_to_irq(plat->cd_gpio), host);
-		gpio_free(plat->cd_gpio);
+	if (gpio_is_valid(tegra_host->cd_gpio)) {
+		free_irq(gpio_to_irq(tegra_host->cd_gpio), host);
+		gpio_free(tegra_host->cd_gpio);
 	}
 
-	if (gpio_is_valid(plat->power_gpio))
-		gpio_free(plat->power_gpio);
+	if (gpio_is_valid(tegra_host->power_gpio))
+		gpio_free(tegra_host->power_gpio);
 
 	clk_disable_unprepare(pltfm_host->clk);
 	clk_put(pltfm_host->clk);

drivers/mmc/host/sdhci.h

@@ -229,6 +229,18 @@
 
 /* 60-FB reserved */
 
+#define SDHCI_PRESET_FOR_SDR12 0x66
+#define SDHCI_PRESET_FOR_SDR25 0x68
+#define SDHCI_PRESET_FOR_SDR50 0x6A
+#define SDHCI_PRESET_FOR_SDR104        0x6C
+#define SDHCI_PRESET_FOR_DDR50 0x6E
+#define SDHCI_PRESET_DRV_MASK  0xC000
+#define SDHCI_PRESET_DRV_SHIFT  14
+#define SDHCI_PRESET_CLKGEN_SEL_MASK   0x400
+#define SDHCI_PRESET_CLKGEN_SEL_SHIFT	10
+#define SDHCI_PRESET_SDCLK_FREQ_MASK   0x3FF
+#define SDHCI_PRESET_SDCLK_FREQ_SHIFT	0
+
 #define SDHCI_SLOT_INT_STATUS	0xFC
 
 #define SDHCI_HOST_VERSION	0xFE
@@ -269,7 +281,7 @@ struct sdhci_ops {
 	unsigned int	(*get_max_clock)(struct sdhci_host *host);
 	unsigned int	(*get_min_clock)(struct sdhci_host *host);
 	unsigned int	(*get_timeout_clock)(struct sdhci_host *host);
-	int		(*platform_8bit_width)(struct sdhci_host *host,
+	int		(*platform_bus_width)(struct sdhci_host *host,
 					       int width);
 	void (*platform_send_init_74_clocks)(struct sdhci_host *host,
 					     u8 power_mode);

drivers/mmc/host/sh_mobile_sdhi.c

@@ -23,6 +23,7 @@
 #include <linux/slab.h>
 #include <linux/mod_devicetable.h>
 #include <linux/module.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/mmc/host.h>
 #include <linux/mmc/sh_mobile_sdhi.h>
@@ -32,6 +33,16 @@
 
 #include "tmio_mmc.h"
 
+struct sh_mobile_sdhi_of_data {
+	unsigned long tmio_flags;
+};
+
+static const struct sh_mobile_sdhi_of_data sh_mobile_sdhi_of_cfg[] = {
+	{
+		.tmio_flags = TMIO_MMC_HAS_IDLE_WAIT,
+	},
+};
+
 struct sh_mobile_sdhi {
 	struct clk *clk;
 	struct tmio_mmc_data mmc_data;
@@ -117,8 +128,18 @@ static const struct sh_mobile_sdhi_ops sdhi_ops = {
 	.cd_wakeup = sh_mobile_sdhi_cd_wakeup,
 };
 
+static const struct of_device_id sh_mobile_sdhi_of_match[] = {
+	{ .compatible = "renesas,shmobile-sdhi" },
+	{ .compatible = "renesas,sh7372-sdhi" },
+	{ .compatible = "renesas,r8a7740-sdhi", .data = &sh_mobile_sdhi_of_cfg[0], },
+	{},
+};
+MODULE_DEVICE_TABLE(of, sh_mobile_sdhi_of_match);
+
 static int sh_mobile_sdhi_probe(struct platform_device *pdev)
 {
+	const struct of_device_id *of_id =
+		of_match_device(sh_mobile_sdhi_of_match, &pdev->dev);
 	struct sh_mobile_sdhi *priv;
 	struct tmio_mmc_data *mmc_data;
 	struct sh_mobile_sdhi_info *p = pdev->dev.platform_data;
@@ -126,7 +147,7 @@ static int sh_mobile_sdhi_probe(struct platform_device *pdev)
 	int irq, ret, i = 0;
 	bool multiplexed_isr = true;
 
-	priv = kzalloc(sizeof(struct sh_mobile_sdhi), GFP_KERNEL);
+	priv = devm_kzalloc(&pdev->dev, sizeof(struct sh_mobile_sdhi), GFP_KERNEL);
 	if (priv == NULL) {
 		dev_err(&pdev->dev, "kzalloc failed\n");
 		return -ENOMEM;
@@ -135,15 +156,14 @@ static int sh_mobile_sdhi_probe(struct platform_device *pdev)
 	mmc_data = &priv->mmc_data;
 
 	if (p) {
-		p->pdata = mmc_data;
 		if (p->init) {
 			ret = p->init(pdev, &sdhi_ops);
 			if (ret)
-				goto einit;
+				return ret;
 		}
 	}
 
-	priv->clk = clk_get(&pdev->dev, NULL);
+	priv->clk = devm_clk_get(&pdev->dev, NULL);
 	if (IS_ERR(priv->clk)) {
 		ret = PTR_ERR(priv->clk);
 		dev_err(&pdev->dev, "cannot get clock: %d\n", ret);
@@ -153,10 +173,9 @@ static int sh_mobile_sdhi_probe(struct platform_device *pdev)
 	mmc_data->clk_enable = sh_mobile_sdhi_clk_enable;
 	mmc_data->clk_disable = sh_mobile_sdhi_clk_disable;
 	mmc_data->capabilities = MMC_CAP_MMC_HIGHSPEED;
+	mmc_data->write16_hook = sh_mobile_sdhi_write16_hook;
 	if (p) {
 		mmc_data->flags = p->tmio_flags;
-		if (mmc_data->flags & TMIO_MMC_HAS_IDLE_WAIT)
-			mmc_data->write16_hook = sh_mobile_sdhi_write16_hook;
 		mmc_data->ocr_mask = p->tmio_ocr_mask;
 		mmc_data->capabilities |= p->tmio_caps;
 		mmc_data->capabilities2 |= p->tmio_caps2;
@@ -187,6 +206,11 @@ static int sh_mobile_sdhi_probe(struct platform_device *pdev)
 	 */
 	mmc_data->flags |= TMIO_MMC_SDIO_IRQ;
 
+	if (of_id && of_id->data) {
+		const struct sh_mobile_sdhi_of_data *of_data = of_id->data;
+		mmc_data->flags |= of_data->tmio_flags;
+	}
+
 	ret = tmio_mmc_host_probe(&host, pdev, mmc_data);
 	if (ret < 0)
 		goto eprobe;
@@ -199,33 +223,33 @@ static int sh_mobile_sdhi_probe(struct platform_device *pdev)
 	irq = platform_get_irq_byname(pdev, SH_MOBILE_SDHI_IRQ_CARD_DETECT);
 	if (irq >= 0) {
 		multiplexed_isr = false;
-		ret = request_irq(irq, tmio_mmc_card_detect_irq, 0,
+		ret = devm_request_irq(&pdev->dev, irq, tmio_mmc_card_detect_irq, 0,
 				  dev_name(&pdev->dev), host);
 		if (ret)
-			goto eirq_card_detect;
+			goto eirq;
 	}
 
 	irq = platform_get_irq_byname(pdev, SH_MOBILE_SDHI_IRQ_SDIO);
 	if (irq >= 0) {
 		multiplexed_isr = false;
-		ret = request_irq(irq, tmio_mmc_sdio_irq, 0,
+		ret = devm_request_irq(&pdev->dev, irq, tmio_mmc_sdio_irq, 0,
 				  dev_name(&pdev->dev), host);
 		if (ret)
-			goto eirq_sdio;
+			goto eirq;
 	}
 
 	irq = platform_get_irq_byname(pdev, SH_MOBILE_SDHI_IRQ_SDCARD);
 	if (irq >= 0) {
 		multiplexed_isr = false;
-		ret = request_irq(irq, tmio_mmc_sdcard_irq, 0,
+		ret = devm_request_irq(&pdev->dev, irq, tmio_mmc_sdcard_irq, 0,
 				  dev_name(&pdev->dev), host);
 		if (ret)
-			goto eirq_sdcard;
+			goto eirq;
 	} else if (!multiplexed_isr) {
 		dev_err(&pdev->dev,
 			"Principal SD-card IRQ is missing among named interrupts\n");
 		ret = irq;
-		goto eirq_sdcard;
+		goto eirq;
 	}
 
 	if (multiplexed_isr) {
@@ -234,15 +258,15 @@ static int sh_mobile_sdhi_probe(struct platform_device *pdev)
 			if (irq < 0)
 				break;
 			i++;
-			ret = request_irq(irq, tmio_mmc_irq, 0,
+			ret = devm_request_irq(&pdev->dev, irq, tmio_mmc_irq, 0,
 					  dev_name(&pdev->dev), host);
 			if (ret)
-				goto eirq_multiplexed;
+				goto eirq;
 		}
 
 		/* There must be at least one IRQ source */
 		if (!i)
-			goto eirq_multiplexed;
+			goto eirq;
 	}
 
 	dev_info(&pdev->dev, "%s base at 0x%08lx clock rate %u MHz\n",
@@ -252,28 +276,12 @@ static int sh_mobile_sdhi_probe(struct platform_device *pdev)
 
 	return ret;
 
-eirq_multiplexed:
-	while (i--) {
-		irq = platform_get_irq(pdev, i);
-		free_irq(irq, host);
-	}
-eirq_sdcard:
-	irq = platform_get_irq_byname(pdev, SH_MOBILE_SDHI_IRQ_SDIO);
-	if (irq >= 0)
-		free_irq(irq, host);
-eirq_sdio:
-	irq = platform_get_irq_byname(pdev, SH_MOBILE_SDHI_IRQ_CARD_DETECT);
-	if (irq >= 0)
-		free_irq(irq, host);
-eirq_card_detect:
+eirq:
 	tmio_mmc_host_remove(host);
 eprobe:
-	clk_put(priv->clk);
 eclkget:
 	if (p && p->cleanup)
 		p->cleanup(pdev);
-einit:
-	kfree(priv);
 	return ret;
 }
 
@@ -281,29 +289,13 @@ static int sh_mobile_sdhi_remove(struct platform_device *pdev)
 {
 	struct mmc_host *mmc = platform_get_drvdata(pdev);
 	struct tmio_mmc_host *host = mmc_priv(mmc);
-	struct sh_mobile_sdhi *priv = container_of(host->pdata, struct sh_mobile_sdhi, mmc_data);
 	struct sh_mobile_sdhi_info *p = pdev->dev.platform_data;
-	int i = 0, irq;
-
-	if (p)
-		p->pdata = NULL;
 
 	tmio_mmc_host_remove(host);
 
-	while (1) {
-		irq = platform_get_irq(pdev, i++);
-		if (irq < 0)
-			break;
-		free_irq(irq, host);
-	}
-
-	clk_put(priv->clk);
-
 	if (p && p->cleanup)
 		p->cleanup(pdev);
 
-	kfree(priv);
-
 	return 0;
 }
 
@@ -314,12 +306,6 @@ static const struct dev_pm_ops tmio_mmc_dev_pm_ops = {
 	.runtime_resume = tmio_mmc_host_runtime_resume,
 };
 
-static const struct of_device_id sh_mobile_sdhi_of_match[] = {
-	{ .compatible = "renesas,shmobile-sdhi" },
-	{ }
-};
-MODULE_DEVICE_TABLE(of, sh_mobile_sdhi_of_match);
-
 static struct platform_driver sh_mobile_sdhi_driver = {
 	.driver		= {
 		.name	= "sh_mobile_sdhi",

drivers/mmc/host/wmt-sdmmc.c

@@ -1012,7 +1012,7 @@ static const struct dev_pm_ops wmt_mci_pm = {
 
 static struct platform_driver wmt_mci_driver = {
 	.probe = wmt_mci_probe,
-	.remove = __exit_p(wmt_mci_remove),
+	.remove = wmt_mci_remove,
 	.driver = {
 		.name = DRIVER_NAME,
 		.owner = THIS_MODULE,

include/linux/mfd/tmio.h

@@ -64,12 +64,6 @@
  * Some controllers can support SDIO IRQ signalling.
  */
 #define TMIO_MMC_SDIO_IRQ		(1 << 2)
-/*
- * Some platforms can detect card insertion events with controller powered
- * down, using a GPIO IRQ, in which case they have to fill in cd_irq, cd_gpio,
- * and cd_flags fields of struct tmio_mmc_data.
- */
-#define TMIO_MMC_HAS_COLD_CD		(1 << 3)
 /*
  * Some controllers require waiting for the SD bus to become
  * idle before writing to some registers.
@@ -116,18 +110,6 @@ struct tmio_mmc_data {
 	void (*clk_disable)(struct platform_device *pdev);
 };
 
-/*
- * This function is deprecated and will be removed soon. Please, convert your
- * platform to use drivers/mmc/core/cd-gpio.c
- */
-#include <linux/mmc/host.h>
-static inline void tmio_mmc_cd_wakeup(struct tmio_mmc_data *pdata)
-{
-	if (pdata)
-		mmc_detect_change(dev_get_drvdata(pdata->dev),
-				  msecs_to_jiffies(100));
-}
-
 /*
  * data for the NAND controller
  */

include/linux/mmc/card.h

@@ -53,6 +53,9 @@ struct mmc_ext_csd {
 	u8			part_config;
 	u8			cache_ctrl;
 	u8			rst_n_function;
+	u8			max_packed_writes;
+	u8			max_packed_reads;
+	u8			packed_event_en;
 	unsigned int		part_time;		/* Units: ms */
 	unsigned int		sa_timeout;		/* Units: 100ns */
 	unsigned int		generic_cmd6_time;	/* Units: 10ms */
@@ -83,7 +86,7 @@ struct mmc_ext_csd {
 	unsigned int            data_tag_unit_size;     /* DATA TAG UNIT size */
 	unsigned int		boot_ro_lock;		/* ro lock support */
 	bool			boot_ro_lockable;
-	u8			raw_exception_status;	/* 53 */
+	u8			raw_exception_status;	/* 54 */
 	u8			raw_partition_support;	/* 160 */
 	u8			raw_rpmb_size_mult;	/* 168 */
 	u8			raw_erased_mem_count;	/* 181 */
@@ -187,6 +190,18 @@ struct sdio_func_tuple;
 
 #define SDIO_MAX_FUNCS		7
 
+enum mmc_blk_status {
+	MMC_BLK_SUCCESS = 0,
+	MMC_BLK_PARTIAL,
+	MMC_BLK_CMD_ERR,
+	MMC_BLK_RETRY,
+	MMC_BLK_ABORT,
+	MMC_BLK_DATA_ERR,
+	MMC_BLK_ECC_ERR,
+	MMC_BLK_NOMEDIUM,
+	MMC_BLK_NEW_REQUEST,
+};
+
 /* The number of MMC physical partitions.  These consist of:
  * boot partitions (2), general purpose partitions (4) in MMC v4.4.
  */
@@ -295,6 +310,11 @@ static inline void mmc_part_add(struct mmc_card *card, unsigned int size,
 	card->nr_parts++;
 }
 
+static inline bool mmc_large_sector(struct mmc_card *card)
+{
+	return card->ext_csd.data_sector_size == 4096;
+}
+
 /*
  *  The world is not perfect and supplies us with broken mmc/sdio devices.
  *  For at least some of these bugs we need a work-around.

include/linux/mmc/dw_mmc.h

@@ -209,8 +209,10 @@ struct dw_mci_dma_ops {
 #define DW_MCI_QUIRK_HIGHSPEED			BIT(2)
 /* Unreliable card detection */
 #define DW_MCI_QUIRK_BROKEN_CARD_DETECTION	BIT(3)
-/* Write Protect detection not available */
-#define DW_MCI_QUIRK_NO_WRITE_PROTECT		BIT(4)
+
+/* Slot level quirks */
+/* This slot has no write protect */
+#define DW_MCI_SLOT_QUIRK_NO_WRITE_PROTECT	BIT(0)
 
 struct dma_pdata;
 

include/linux/mmc/sdhci.h

@@ -94,6 +94,7 @@ struct sdhci_host {
 #define SDHCI_QUIRK2_HOST_NO_CMD23			(1<<1)
 /* The system physically doesn't support 1.8v, even if the host does */
 #define SDHCI_QUIRK2_NO_1_8_V				(1<<2)
+#define SDHCI_QUIRK2_PRESET_VALUE_BROKEN		(1<<3)
 
 	int irq;		/* Device IRQ */
 	void __iomem *ioaddr;	/* Mapped address */

include/linux/platform_data/mmc-esdhc-imx.h

@@ -39,5 +39,6 @@ struct esdhc_platform_data {
 	unsigned int cd_gpio;
 	enum wp_types wp_type;
 	enum cd_types cd_type;
+	int max_bus_width;
 };
 #endif /* __ASM_ARCH_IMX_ESDHC_H */